1

Open Phase Conditions in Transformers

Analysis and Protection Algorithm
Amir Norouzi
GE Digital Energy
Markham, ON
[email protected]

AbstractThis paper first provides an in-depth analysis of

open phase conditions in three phase power transformers. It
describes why and how, upon loss of a single phase on the
high or primary side of a transformer, voltages and currents
on the low or secondary side greatly depend not only on the
windings configuration but also sometimes on transformers core
construction as well. Some particular cases are discussed in which
detecting a high side open phase is very difficult with current
transformers (CT) only on the low side. Then after examination
of the secondary voltages and currents practical and reliable
algorithms are presented for identification and protection of
high side open phase conditions from the low side of a power
transformer. Digital simulation is used for verification of the
analysis results and the protection algorithms.

I. I NTRODUCTION
Open phase condition frequently occurs in power systems,
particularly in medium voltage distribution networks (such
as 33KV or below) in rural or remote areas where broken
conductor, loose connection or a blown fuse can lead to an
open phase. Some other cases of an open phase may involve
a defective contact of a circuit breaker. This is considered
a series fault with a different fault current calculation and
sequence networks connection than other known shunt faults
such as LG or LLG. In addition, an open phase on one side of
a transformer can be very difficult to detect on the other side
depending on the transformers core and winding configuration
as well as loading level.
In medium voltage distribution systems, industrial plants,
and rural areas and for economic reasons often smaller transformers, such as 5MVA or below, are protected mostly on the
load (low) side with the possibility of only fuses on the high
side usually provided by the local utility. As will be shown,
with an open phase on the high side of a transformer there
are cases that the three phase voltages and currents on the low
side could be fairly balanced, particularly in lower loading
conditions, such that neither overcurrent nor negative sequence
current elements can pick up a fault. In fact in lower loading
conditions, even as high as 50% , the transformer may continue
normal operation for hours and possibly longer with acceptable
balanced voltages and currents on the low side while there
is an open phase on the high side. Only in higher loading
conditions may the protection relays pick up a fault, usually
on negative sequence or sensitive ground overcurrent.
An open phase anomaly can also occur in distributed
generation (DG). Many small DG sites, including landfill,

biogas, solar and wind power generation, are located in rural

or remote areas with high chances of loss of a phase on the
side of the local utility grid. With relay protection only on
the low side of the grid interconnection transformer and with
certain core or winding configurations an open phase on the
grid side may go unnoticed for a while particularly in lower
loading conditions.
It may initially seem that a high side open phase in a
transformer will result in imbalances on the low side with
enough significance that can be detected. Further analytical
investigation will show the amount of imbalances of current
and voltage on the low side depends on the winding configuration as well as sometimes core construction. For instance,
while in a Y - transformer (ungrounded Y) an open phase
will create major unbalance voltages and currents that can be
easily detected, in a Yg - transformer it may be very difficult
to detect an open phase from the low side depending on the
transformer loading.
An open phase on a transformers primary side will create
negative sequence current and voltage as well as ground
overcurrent if it has Yg winding on the same side. These
are the main conditions that can be used to detect a fault
when CTs are only on the secondary side of the transformer.
However, relying on the low side negative sequence or ground
overcurrent for open phase detection in transformers has two
disadvantages. The first relates to the inherent inability of
this method to detect an open phase condition in certain
transformer core and winding configurations and lower loadings, leading to a gap in transformer protective relaying. This
will be discussed in details in the next sections. The second
disadvantage is that a negative sequence or ground overcurrent
responding to an open phase condition on a transformers high
side could be unhelpful or even misleading in identifying the
real cause of the problem, without which the system may not
return to normal operating conditions. The low side protective
relays will not allow the system to be re-energized because
of the persistent high negative sequence or ground currents
which leads to protracted down time with direct and indirect
financial losses.
Therefore even in those transformer configurations that an
open phase creates substantial and detectable imbalances on
the low side finding the true cause of the protection relay
operation can be confusing and tedious, particularly in remote
locations with not an easy access to technical expertise. If the
protection relay can accurately point to the specific cause of

the imbalance conditions, namely that there is an open phase

on the high side, fixing the problem will be a much easier and
faster task which will significantly reduce the down time.
II. T HREE -P HASE T RANSFORMERS - A B RIEF R EVIEW
In analyzing open phase conditions in three-phase transformers we will need a basic understanding of different ways
transformers are built, particularly the core construction. While
in steady-state study of a power system we may only need to
know a transformers parameters, ratings and winding configuration understanding a three-phase transformers response to
an open phase may also require further attention to its physical
construction.

zero. As illustrated in Figure 1 in a three-leg core there is no

return path for 0 and it has to pass through air gap or the tank
with much higher magnetic reluctance than the core. This path
of high reluctance for 0 in a three-leg core requires much
higher amount of zero sequence magnetizing current which
could lead to saturation and excessive heat. This equivalents
to a much lower zero sequence magnetizing reactance in the
parallel branch of the transformer model, typically about 1 pu,
which cannot be necessarily ignored when dealing with fault
current calculations and zero sequence networks. For comparison, the magnetizing reactance of three-phase transformers
for balanced conditions is typically 15 20 pu which can be
easily ignored in the parallel branch of a transformer model.

A. Construction of Three-Phase Transformers

Three-phase transformers are constructed in one of two
ways: either by connecting three single phase transformers
in a three-phase bank or by three sets of windings wrapped
on a common core. A single core three-phase construction
is widely preferred as it is more cost effective, lighter and
smaller. However, in the older single phase bank approach each
unit may be replaced individually in the event of a failure of
that particular unit which is an advantage over common core
construction.
Typically the common core construction is either core type
or shell type as illustrated in Figures 1 to 4. Primary and
secondary windings can be connected as either Y or . Core
type construction consists of legs (or limbs) and yokes. Both
primary and secondary windings of each phase are on the same
leg one on top of the other with the high voltage winding on
the outer side. This winding construction has two advantages:
it makes high voltage insulation easier and it results in less
leakage flux. Yokes are the top and bottom part of the core
that joins the legs together and have no windings.

Fig. 2.

To provide a return path for 0 in unbalanced systems

a fourth and even a fifth leg is added to the core type
transformers as illustrated in Figures 2 and 3. Both four and
five leg core type transformers have similar performance in
dealing with zero sequence flux. Five-leg core helps reduce
the size of the yoke as it will carry less 0 , thus smaller
transformer size. Four and five leg transformers provide low
reluctance path for 0 through the core with low zero sequence
magnetizing current and large magnetizing reactance.

Fig. 3.
Fig. 1.

Four-Leg Core Type Transformer

Five-Leg Core Type Transformer

Three-Leg Core Type Transformer

Core type construction may have 3, 4 or 5 legs with

great impact on zero sequence flux, 0 , and zero sequence
magnetizing current or magnetizing reactance, X0M . In a
balanced power system the three phase fluxes, a , b and
c , are also balanced with a vector sum of zero at the yoke.
However, an unbalanced power system creates zero sequence
flux as the sum of the three phase fluxes, a + b + c , is not

Shell type three-phase transformer design is illustrated in

Figure 4 which is a variation of five-leg core type transformer.
Three phase fluxes have multiple paths within the core. Shell
type transformers provide return path for zero sequence flux
and thus demonstrate a performance similar to four or five leg
core type transformers when exposed to unbalanced system,
i.e. low reluctance path for 0 and small zero sequence
magnetizing current.

Magnitudes of induced voltage, e1 , and flux are linearly

proportional. With a known frequency and winding turns
equation 3 may be reduced to Vrms = Km which is a
simple linear relationship.
Magnitude of the established core flux is solely determined by the magnitude of the applied voltage, its
frequency and winding turns. In other words, if voltage
V1 is applied to winding 1 magnetic flux is established
in the core and similarly if flux passes through winding
1 voltage V1 will be induced in that winding.
We will revisit these observations, particularly the last one,
when discussing open phase conditions in transformers.

Fig. 4.

Shell Type Transformer

B. Fundamental Equation of Magnetic Flux in Transformers

In discussing open phase conditions in transformers we also
need to review the basic concept of the interaction between
magnetic flux and induced voltage in transformers. This will
also help understand transformers response to an open phase.
Figure 5 shows a single phase transformer with V1 =
Vm cos t applied to the primary winding with a total number
of N1 turns with no loads on the secondary winding. Recall
from basic theory of transformer operation that a countervoltage, e1 , will be induced in winding 1 that is almost equal
to V1 provided that we assume magnetic reluctance of the core,
<, and winding resistance, R, are negligible. This means that
magnetization current and voltage drop in winding 1 are very
small which is a reasonable assumption as long as the core
is not saturated and operates within its linear magnetization
curve.
The induced voltage, e1 , will establish a magnetic flux, ,
in the core according to the Faradays law, i.e. e1 = N1 d
dt .
With the assumption of V1 e1 it follows that the flux will
also be sinusoidal and can be obtained as:
Z
1
Vm cos t dt
(1)
=
N1

Vm
2Vrms
=
sin t =
sin t
N1
2f N1

(2)

Therefore
magnetic flux, , is sinusoidal with an amplitude
2Vrms
of m = 2f
N1 . We can write equation 2 in the following
well-known format:
Vrms = 4.44N1 f m

(3)

Equation 3 is the fundamental equation that defines how

voltage and magnetic flux interact in an unloaded transformer.
The assumption is again that the core is not saturated and
windings voltage drop is negligible which are essential to this
equation. The following important observations can be made
from equation 3:
As long as the core is not saturated and its magnetic
reluctance is very small if a sinusoidal voltage is applied
to one of the windings on the core it will establish a
sinusoidal magnetic flux within the core. Considering
that the windings voltage drop is negligible the induced
voltage e1 is equal to the applied voltage V1 .

Fig. 5.

Illustration of V1 , e1 and in an Unloaded Transformer

III. A NALYSIS OF O PEN P HASE C ONDITIONS IN

T HREE -P HASE T RANSFORMERS
Before presenting this analysis of open phase conditions
in three-phase transformers we need to review some basic
assumptions as below:
Open phase conditions or loss of a phase refers to
one phase of the three phases being physically and
unintentionally disconnected on the primary side of a
transformer. This could occur for several reasons such
as a loose cable, a broken conductor, a blown fuse, a
circuit breaker with one defective contact, etc.
Primary and high side terms are used interchangeably.
This is the high voltage side of the transformer which is
generally the grid side.
Secondary and low side terms are used interchangeably.
This is the low voltage side of the transformer which is
generally the load or distributed generation (DG) side.
Open phase is assumed to have occurred on the primary
side of a transformer.
There are no current transformers (CT) or protection
voltage transformers (PT) on the high voltage terminals
of the transformers being discussed.
First in III-A the impact of an open phase on the primary
winding are discussed independently and without considering
any magnetic or electric interaction between high and low side
of the transformer. Then in III-B with the help of the first
part open phase conditions will be examined with complete
consideration of the interaction between the primary and
secondary sides.

A. Primary Side Investigation (Independent From the Low

Side)
Grounded (Yg ) and ungrounded ( or Y ) primary windings
will respond differently to an open phase.
1) Grounded Primary (Yg ): In Figure 6 with phase A open
IA is zero. It is assumed that the utility grid supplying the
high side is strong enough that upon loss of phase A voltages
of the other phases, VB and VC will essentially remain the
same.
Now if the transformer is three-leg core type, as illustrated
in Figure 1, the only return path for A and B is through the
coil of the disconnected phase A. Therefore, A = B C
which is still the same as when phase A was connected to
the transformer (in balanced conditions before the phase loss
A + B + C = 0). This is because from observations of
Section II-B we know magnetic flux of a winding is solely
determined by voltage, frequency and winding turns and here
with all three parameters essentially the same before and after
the open phase conditions B and C will also remain the
same. Hence the same A is passing through winding A which
means the same voltage, VA , will be induced in this winding.
Therefore, in a three-leg transformer with Yg primary windings
the winding with the lost phase will have an induced voltage
equal to the voltage before the open phase occurrence.

still VBC and remains unchanged. However, VBC is evenly

divided between coils A and C . After the loss of phase A
and considering the dot convention the followings are true for
the coil voltages and line currents:
VB = VBC

(5)

1
1
VA = VC = VBC = VBC 6 180
2
2

(6)

IA = 0; IC = IB

(7)

For a D11 configuration, equation 6 will become VA =

VB = 12 VBC with VC = VBC .

Fig. 7.

Primary Winding with Phase A Open

For an ungrounded Y primary in Figure 8 and with the

same assumption that VB and VC are the same before and
after phase A is open we will have the followings for voltages
across each coil and line currents:
VA = 0
VB = VC =
Fig. 6.

(8)
1
VBC
2

(9)

Yg Primary Winding with Phase A Open

IA = 0; IC = IB
However, in other types of transformer cores upon open
phase conditions either a fraction of B and C will pass
through winding A (4-leg, 5-leg, shell type) or there is no flux
linkage between the phases at all (three single phase bank).
In either case there is very little or no voltage induced in the
winding with lost phase.
As illustrated in Figure 6 and regardless of the core type,
upon loss of phase A the ground current at the neutral point
of the transformer is per below equation. We will use this
equation later in the discussions on the open phase condition
in transformers.
IG = 3I0 = IB + IC

(4)

2) Ungrounded Primary ( or Y ): Figure 7 illustrates

a primary winding with phase A open. With an ABC
phase sequence this is D1 configuration, i.e. side lags the
secondary Y side by 30 . The individual phase coils are called
A , B and C . With phase A open the voltage across B is

(10)

Hence the following observations can be made for an

ungrounded primary winding, or Y , when one phase in
open:
In primary the coil with no lost phases will have
the same voltage as before the open phase conditions.
The other two coils will maintain half of their original
voltages. These voltages will have the same magnitude
and phase angle although the new angle is totally different from before the loss of phase. This is regardless
of the physical construction of the transformer, whether
three/four/five legs or three single phase bank. Besides,
the remaining two coils will have currents with equal
magnitude but 180 apart. With these voltages and currents the system will be substantially unbalanced.
In Y primary voltage of the coil with lost phase is
always zero regardless of the physical construction of
the transformer. This is because the other two coils will
always have equal but opposite voltages which means

the magnetic fluxes of the two remaining coils are also

equal and opposite, i.e. B = C . Therefore, in core
and shell type transformers no flux can go through any
paths, including leg A or A , except the path of legs B
and C and part of the yokes that joints these two legs.
This can be observed by examination of Figures 2 to 4.
Similar to winding case, currents of the two remaining
phases of the Y winding will be equal in magnitude but
with opposite direction, i.e. Ic = IB .

Fig. 9.

Fig. 8.

Y Primary Winding with Phase A Open

B. Open Phase Conditions in Transformers

With the discussion and findings of Section III-A we can
now investigate open phase conditions in transformers in
greater details with consideration of magnetic and electrical
interactions within the three-phase transformer. Here
transformers with commonly used configuration, including
Yg -, -Yg , Yg -Yg , - are examined. Ungrounded Y will
also be discussed. The first letter indicates the high side of
the transformer.
1) Yg - Transformers: Yg - transformer is one of the
most commonly used configurations. With Yg on the high side
each coil is subjected to 13 or 57.7% of line voltage which
makes it easier to insulate the primary coils. In distributed
generation (DG) applications with the DG source on the
side the grid cannot contribute to a ground fault on the DG
generator while in case of a ground fault on the grid DG
can contribute to the fault which makes the anti-islanding
protection more practical by sensing the ground current on
the neutral of the Yg . This is a useful characteristic of this
configuration which makes it preferable in DG.
Figure 9 illustrates a Yg - transformer with phase A open
on the high side. Assuming that the high side is strong enough
that VB and VC are almost the same after loss of phase A
(except for additional voltage drop due to larger IB and IC
as will be discussed later) low side coils of b and c will
have the same induced voltage as before loss of phase A. This
is because high side coils of B and C still have the same
voltage, hence the same induced voltage on the corresponding
low side coils. Therefore, upon loss of phase A, voltage in
coil a will be:
Va = Vb Vc

(11)

Open Phase in a Yg - Transformer

Which is the same as when coil a was energized from the

high side coil A (before loss of phase A we had Va + Vb +
Vc = 0).
It is important to notice that, despite discussions on Yg
primary in Section III-A1 and how similar voltage may or
may not be induced on the coil with lost phase depending
on the construction of the transformer, here Va and VA are
always re-generated regardless of transformers construction,
including three single-phase banks. This is because the interaction between the primary and secondary coils is taken into
consideration. In fact re-generation of voltages of the coils
with lost phase is by a different mechanism than what was
discussed in Section III-A1.
In an unloaded Yg - transformer both the high and low
side voltages corresponding to the lost phase is perfectly
re-generated such that effectively no change in three phase
voltage magnitudes and angels is seen on primary and
secondary sides. When loads are added the transformer will
continue to supply the low side loads from all three phases
as before the phase loss with the following important notes:
1) With almost the same line voltages on the low side the
transformer will supply nearly the same power to the
loads.
2) On the high side power is carried only by the remaining
two phases. Therefore, the current on those phases will
be roughly 50% larger than before the loss of phase.
However, since the high side is no longer a three-phase
system new phase angles will be established. The new
IB and IC will be apart considerably different from the
120 of a three-phase balanced system.
3) The high side coil with lost voltage and its corresponding coil on the low side do not carry any power, despite
both coils being energized with almost the same voltage.
Coil a on the low side doesnt carry any current except
a very small current for magnetization and losses. This
is simply because high side coil A doesnt transfer any
power to coil a and this is the only way coil a can
receive power from the primary side. It follows that
power being supplied to the load by phases a, b and
c all come from only two coils on the low and high
sides, particularly power being supplied by phase a is
actually being provided only by coils b and c. We will

Fig. 10.

Single Line Diagram of the Sample Power System

Figure 11 illustrates simulation results for an open phase

condition which occurs at t = 0.1Sec. on phase A when the
transformer is lightly loaded at 60KW. Only low and high
side voltages and currents are shown. Low side voltages and
currents as well as high side voltages are very balanced after
the loss of phase and almost the same power is being supplied
to the load. While IA = 0 after phase A is lost the other two
currents, IB and IC considerably increase to compensate for
the lost phase in order to supply the same power to the load.

Further simulation results show that on the low side II21 and VV21
are about 0.62% which demonstrate a quite balanced system.
Transformer LV Voltages- Vab, Vbc, Vca

Transformer LV Currents- Ia, Ib, Ic

1.05

0.036

pu

pu

0.034
1

0.032

0.95

0.03

Transformer HV Voltages- VAn, VBn, VCn

0.05

0.1

0.15

0.2

Transformer HV Currents- IA, IB, IC

1.05

pu

0.06

pu

see that this is fundamentally different from three-leg

core Yg -Yg transformers where the low side coil with
lost phase carries current and real power because the
re-generated voltage comes from flux interaction, not a
simple voltage build-up. Hence despite the line currents
Ia , Ib and Ic being almost unchanged the current of coils
b and c are roughly 50% larger than before to supply the
additional power to be transferred by line a.
4) As the loads are being added on the low side the
perfect balanced voltages of the unloaded transformer
will start to become more unbalanced with line voltages
and currents being more and more unbalanced. The main
elements impacting the system balance conditions are
leakage flux and voltage drop. With higher currents after
the phase loss come larger leakage flux and voltage
drop. As the high side line currents and also low side
coil currents will become considerably larger roughly
by a factor of 50% two types of voltage drops will
appear: one is voltage drop on the feeders supplying the
transformers primary side which makes the high side
terminal voltages lower than before.The other voltage
drop is due to high and low side active coils carrying
again about 50% more current than before. The coil
voltage drops impact the low side terminal voltages of
the active coils, but the coil corresponding to the lost
phase doesnt carry current and not being impacted by
the internal transformer voltage drops.
To better demonstrate the above characteristics in Yg -
transformers, a digital simulation using MATLABs Simulink
was performed. The transformer has a five-leg core, but we
saw that in Yg - this has no impact on transformers response
to an open phase conditions. Consider the power system of
Figure 10. Two different loading conditions are considered:
a light resistive load of 60KW and a larger load of 600KW
(33%).

0.04

0.02

0.95

0.05

0.1
Time (Sec)

0.15

0.2

0.05

0.1
Time (Sec)

0.15

0.2

Fig. 11. Simulation Results for a Yg - Transformer After Loss of Phase

A- Load=60KW

Figure 12 illustrates simulation results for the same system

and conditions but the transformer is loaded at 600KW or
33% of its rated power. Here we can see the impact of greater
currents and the associated higher voltage drops and leakage
flux on the system voltages. Although the transformer still
supplies close to 33% of its rated power to the load after the
loss of one phase the high side currents of the two remaining
phases are more than 50% of the rated current. The simulation
results show that on the low side II21 and VV21 are about 5.9%,
much greater than the previous lightly loaded conditions, but
still not a highly unbalanced system. After loss of phase the
transformer still delivers 96.4% of the power it was delivering
before the fault.
Figure 13 illustrates individual coil currents on the low
() side. As discussed earlier although coil a is energized it
doesnt carry any current (except for the magnetizing current
and losses) and power after loss of phase. All three phases on
the low side receive power from only the two remaining coils.
The protection elements that may seem to be applicable
to open phase conditions on the transformers low side are
mainly negative sequence voltage or current as well as ground
overcurrent. From the above discussions and example we see
that in a Yg - transformer negative sequence quantities are
quite low and may not necessarily be relied on for open phase
conditions. The other protection element, ground overcurrent,
is meant to be used for ground faults on the grid side of
the transformer and hence is usually set somewhat below
the ground fault level which is most of the time considerably higher than the transformers rated phase current. From
equation 4 we know that the ground current of the Yg is
IG = IB + IC upon loss of phase A. However, this is
not a conventional three-phase system with current vectors
120 apart. Assuming that upon loss of a phase the high side
currents
will rise about 50%, ground current, IG , is roughly

3 times the phase current, and that the ground overcurrent

is set 50% higher than the transformers full load current we

can estimate that if transformers pre-fault current is up to
about 60% of its rated current ground overcurrent element will
not pick any fault. This is why this protection element is not
reliable either in dealing with open phase conditions. Even if
ground overcurrent detects a fault there is little indication that
the fault is actually due to an open phase and not a ground
fault.
Transformer LV Voltages Vab, Vbc, Vca

Transformer LV Currents- Ia, Ib, Ic

1.1

0.4

pu

pu

1
0.3

0.9

0.8

0.2

Transformer HV Voltages- VAn, VBn, VCn

Transformer HV Currents- IA, IB, IC

1.1
0.6

pu

pu

0.9

0.8

0.4

0.2

0.05

0.1
Time (Sec)

0.15

0.2

0.05

0.1
Time (Sec)

0.15

0.2

Fig. 12. Simulation Results for a Yg - Transformer After Loss of Phase

A- Load=600KW

Coil Currents- Secondary Side

0.35

0.3

pu

0.2

0.1

specific conclusions applicable to open phase conditions in

any type of transformer construction and configuration and
series fault calculations dont provide such analytical tool.
Besides, fault calculation methods are not necessarily capable
of handling those cases that closely depend on the physical
construction of the transformer such as Yg -Yg .
2) Transformers with Ungrounded Primary ( or Y ):
Transformers with or ungrounded Y primary demonstrate
similar characteristics upon loss of a phase regardless of the
secondary configuration or core construction. These characteristics are obtained and discussed in this section. We will
see that same protection principle can be applied to such
transformers as -Yg , -Y , -, Y -, Y -Yg and Y -Y .
What is common among all such transformers with ungrounded primary winding is that upon loss of a single phase
there will be substantial voltage unbalance on both primary
and secondary side of the transformer. As discussed in III-A2
only half of the phase-phase voltage will appear on two of the
primary coils. Therefore, with considerable voltage and current
drops protection elements such as undervoltage or negative
sequence current will pick up a fault on the primary side.
An example is illustrated in Figure 14 where a -Yg
transformer has an open phase A on the high side. With an
ungrounded primary winding, as discussed in III-A2, only
half of the line voltage will be established across the two
coils associated with the lost phase on the high side, i.e. coils
A and C . See equations 6. Therefore, in the corresponding
secondary coils of a and c a voltage equal to half the
pre-fault voltage will be induced. While here, unlike Yg -
transformers, there is no voltage re-generation and existing
protection elements will detect a fault finding the actual cause
of the fault can be a challenge as none of these elements firmly
suggest an open phase condition on the high side.
To further investigate such cases of open phase we can
use the following well-known equations to obtain sequence
currents, I1 and I2 , on the high side of the transformer in
Figure 14 (I0 = 0), where a = 16 120 :
1
(IA + aIB + a2 IC )
(12)
3
1
I2 = (IA + a2 IB + aIC )
3
We observed that IA = 0 and IC = IB . Substituting in
the above equations we will have:
I1 =

0.05

0.1
Time (Sec)

0.15

0.2

Fig. 13.
Coil Currents on the Secondary Side After Loss of Phase ALoad=600KW

A note on open phase fault calculations: Open phase

is considered a series fault in power systems. Similar to
the shunt faults such as LG or LLG sequence network
connections for series faults have also been developed to
calculate system currents and voltages upon such faults,
although series fault calculations are less well-known than
shunt faults. For instance see [3], [6] and [7] for discussions
and examples of such fault calculations. Although fault
currents and voltages can be calculated by open phase
sequence network modeling it wont provide the insight and
systematic examination as how and why certain voltage and
currents are seen upon loss of a phase in a transformer. To
develop a protection algorithm we need to be able to establish

IA = 0

I2
= 16 180
I1

(13)

Similarly for open phase on other phases we have:

IB = 0
IC = 0

I2
= 16 60
I1

(14)

I2
= 16 60
I1

(15)

The above equations are always true for a or ungrounded

Y primary transformer regardless of the core construction and
secondary configuration, whether it is Yg , Y , or . We now

-Yg Transformer with Phase A Open on the High Side

When converting sequence voltages and currents from one

side of a transformer to the other side the positive sequence
values get a phase angle shift in the same direction of the
transformers vector group while negative sequence values get
a phase angle shift in the opposite direction. For example, if
the primary side of a transformer lags the secondary side by
30 then I1P ri. will also lag I1Sec. by 30 while I2P ri. lags
I2Sec. by 30 or leads it by 30 . Hence, for this transformer
I2P ri.
I2Sec.

6
I1Sec. = I1P ri. 60 as I1P ri. and I2P ri will transfer to the
secondary side with the same ratio but opposite phase angle
shifts.
I
We can now establish the following values for I21Sec. , as in
Sec.
Table A, that apply to negative and positive sequence currents
on the low side of a transformer with an ungrounded primary
winding of or Y upon loss of a single phase on the high
side. This is regardless of the core construction and secondary
winding configuration. It also applies to DG cases where there
is a generation source on the low side exporting power to the
grid. All we need to know is the phase angle shift of low side in
relation to the high side. In each case high side equations 13,
14 and 15 are re-written for the low side with appropriate
phase angle shift.
Table A: II12 Values on the Transformers Low side
with an Open Phase on the Ungrounded High side
Case
A Open
B Open
C Open

Pri. and Sec. in phase

1 180
16 60
16 60

Pri. lags Sec. by30

1 120
16 120
16 0

Pri. leads Sec. by30

1 120
16 0
6
1 120

3) Yg -Yg Transformers: So far weve seen that, regardless of the core construction, in Yg - transformers the lost
phase is always re-generated while in transformers with
or Y primary the lost phase is never re-generated. In Yg -Yg
transformers the core construction has a major impact on the
transformers response to an open phase. Depending on the
core type a Yg -Yg transformer may or may not re-generate the
lost phase, making it a special case when dealing with open
phase conditions in transformers, although it is less commonly
used than Yg - transformers. Figure 16 illustrates a Yg -Yg
transformer with phase A open on the high side.
Transformer LV Voltages- Van, Vbn, Vcn

Transformer HV Voltages- VAB, VBC, VCA

0.8

0.8
pu

Fig. 14.

using Table A it can be quickly established if there is an open

phase on the high side and further determine which phase is
actually lost. Values of Table A can be applied in any loading
conditions, including when the transformer is loaded at a very
small percentage of its rated power.
To demonstrate an open phase condition in a transformer
with ungrounded primary a digital simulation is carried out
on the sample single line diagram of the Figure 10 where the
transformer is -Yg with a pre-fault load of 100KW. Phase
B is lost at t = 0.1Sec. Primary and secondary voltages
as well II12 as measured on the low side are illustrated in
Figure 15. As expected two voltages on the primary and hence
two corresponding voltages on the secondary drop to half of
their pre-fault values. This will result in similar drop in the
currents which is a significant unbalance condition. Low side
positive and negative sequence currents have equal magnitudes
with a phase displacement of 120 in accordance with Table
A.
Replacing -Yg transformer of the above example with
other types of ungrounded primary configurations, namely
-Y , -, Y -, Y -Yg and Y -Y , will produce the same
results as far as the transformer voltages and II21 values.
Hence, same principle is applicable to all these transformers
regardless of physical construction of the transformer.

pu

need to obtain the corresponding I1 and I2 relationships on

the secondary side where the CTs are located. This is only a
matter of phase angle shift of the sequence currents.

0.6

0.6

0.4

0.4

I2/I1- Magnitiude

I2/I1- Phase Angle

1
-40
-60
degrees

Table A shows the common phase angle shifts in transformers. Examples of a transformer with primary and secondary
in phase are - (D1-D1) or Y -Y . For other special phase
angle shifts the corresponding II21 can be further determined
with similar exercise. Since phase sequence of the power
system (ABC or ACB) also impacts the vector rotation of
a transformer phase angle shift must be carefully determined
before using the above equations. In any case, with a or
ungrounded Y primary and upon loss of a single phase positive
and negative sequence currents will have equal magnitudes,
i.e. |I2 | = |I1 | both on primary and secondary sides. By

0.5

-80
-100
-120

0.05

0.1
Time (Sec)

0.15

0.2

0.05

0.1
Time (Sec)

0.15

0.2

Fig. 15. Simulation Results for a -Yg Transformer After Loss of Phase
B- Load=100KW

In Section III-A1 we saw how the lost voltage is re-

Transformer LV Voltages- Van, Vbn, Vcn

Transformer LV Currents- Ia, Ib, Ic

1.05

0.036

0.034
pu

This voltage re-generation in Yg -Yg is of course specific to

three-leg core type transformers. When the core has four or
five legs or when the transformer bank consists of three single
phase transformers no voltage re-generation takes place as we
saw earlier. The same principle applies to Yg -Y transformers
in regard to three-leg or other types of construction, although
practically Yg -Y is not a commonly used configuration.
There is another aspect to the process of voltage regeneration in Yg -Yg transformers that makes it yet more
different from Yg - transformers. We saw that in Yg -
transformers as the load increases transformer voltages drop
and also become more unbalanced due to the increased leakage
flux as well as additional voltage drops inside and outside of
the transformer. In Yg -Yg transformers increased leakage flux
has more considerable impact on the re-generated voltage as
the induced voltage comes directly from the flux. So far we
have assumed that the magnetic fluxes of the two remaining
coils entirely pass through the coil with the lost phase to induce
the same voltage as before the loss of phase. See Figure 1 for
a reminder. While this might be true for no or very small load
conditions the fact is that not all the fluxes can pass through
the third leg because in real world the core is not ideal and

0.032

0.95

0.03

Transformer HV Voltages- VAn, VBn, VCn

Transformer HV Currents- IA, IB, IC

1.05
0.06

pu

Yg -Yg Transformer With an Open Phase

pu

Fig. 16.

some portion of the fluxes will go through a path outside of

the core such as air or tank. This portion of the flux is called
leakage flux. The higher the transformer load, i.e. the higher
the flux within each coil, the higher the leakage flux which
means less of the coil fluxes, B and C , will pass through the
third leg with lost phase as a bigger portion of them circulate
outside of the core. This will result in less induced voltage in
the coil of the third leg. Therefore, with larger loads we expect
to see larger voltage drop on the lost phase than a similar Yg -
transformer would have produced.
In summary the important aspects of voltage re-generation
in a Yg -Yg transformer upon loss of a phase on the high side
are:
1) Only in three-leg core type Yg -Yg transformers is the
voltage of the lost phase re-generated. In transformers
with four or five leg cores or a bank of three single phase
transformers there is no voltage re-generation.
2) The voltage of the lost phase is re-generated by the
flux that goes through the coil on the third leg in
accordance with equation 3. Energy is transferred to the
high side coil with the lost phase by magnetic fluxes of
the two remaining phases which is then transferred to the
low side coil. This is different from Yg - transformers
where the voltage is re-generated on the low side due to
electrical interaction between the coils and then induced
back to the primary coil with both coils associated with
the lost phase not carrying any current or power.
3) As the transformer load increases there will be larger
voltage drop on the coils with lost phase due to leakage
fluxes of the primary coils. This means that not all the
fluxes can go through the third leg which then results in
less induced voltage in the coil with lost phase.
To demonstrate characteristics of three-leg Yg -Yg transformers in loss of phase conditions digital simulation was
performed on the sample power system of Figure 10. Two
different loads are considered. Figure 17 illustrates the results
for 60KW load and Figure 18 is for a transformer load of
600KW. Phase A is lost at t = 0.1Sec.

pu

generated internally in a Yg winding when the transformer

has a three-leg core because the magnetic flux of the two
remaining phases will have no other path within the core
than the third leg with the lost phase. In Yg - transformers
the source of voltage re-generation is voltage build-up across
the low side coil with lost phase due to simple electrical
interaction between the three low side coils, which in turn
induces a voltage on the corresponding primary coil as discussed in III-B1. No flux interaction and therefore no energy
transfer between primary and secondary sides is engaged in
this process of voltage re-generation, hence no power from the
low side coil with lost phase as we saw in III-B1. However,
in three-leg Yg -Yg transformers it is the flux build-up in
the third leg that first induces a voltage across the primary
coil with lost phase which then induces a voltage on the
corresponding low side coil. In this process flux interaction
is the source of voltage re-generation and therefore energy
(power) is transferred from the high side coil with lost phase
to its corresponding low side coil and hence all three coils
of the secondary side will carry power as before open phase
condition occurred. This is an unusual case where one of
the transformers primary coils receives power not electrically
from its feeder but rather magnetically from the core.

0.04

0.02

0.95

0.05

0.1
Time (Sec)

0.15

0.2

0.05

0.1
Time (Sec)

0.15

0.2

Fig. 17. Simulation Results for a Three-leg Yg -Yg Transformer After Loss
of Phase A- Load=60KW

10

Transformer LV Voltages- Van, Vbn, Vcn

Transformer LV Currents- Ia, Ib, Ic

0.4

1
0.3

0.8
0.6

pu

pu

Comparing simulation results for Yg -Yg transformer with

that of the Yg - in Section III-B1 we can see that for
similar loads Yg -Yg transformer demonstrates considerably
more unbalance conditions after loss of a phase. While for
the Yg - transformer II12 and VV12 were 0.62% for a 60KW
load and 5.9% for a 600KW load, here simulation results
show that II21 and VV21 are 3.8% for the 60KW load and 30.4%
for the 600KW load which are significantly higher than the
corresponding values in the case of the Yg - transformer.

0.2

0.4
0.1
0.2
0

Transformer HV Voltages- VAn, VBn, VCn

Transformer HV Currents- IA, IB, IC

0.4

Transformer LV Currents- Ia, Ib, Ic

pu

0.3

0.8

0.4

0.35

0.6

pu

Transformer LV Voltages- Van, Vbn, Vcn

1.1

0.2

0.4

pu

pu

0.9

0.1

0.3

0.2

0.8
0

0.25

0.7
0.6

0.05

0.1
Time (Sec)

0.15

0.2

0.05

0.1
Time (Sec)

0.15

0.2

0.2

Transformer HV Voltages- VAn, VBn, VCn

Fig. 19. Simulation Results for a Five-leg Yg -Yg Transformer After Loss
of Phase A- Load=600KW

Transformer HV Currents- IA, IB, IC

1.1
0.6

pu

pu

0.9

A. Yg - Transformers

0.4

0.8
0.2
0.7
0.6

0.05

0.1
Time (Sec)

0.15

0.2

0.05

0.1
Time (Sec)

0.15

0.2

Fig. 18. Simulation Results for a Three-leg Yg -Yg Transformer After Loss
of Phase A- Load=600KW

Figure 19 illustrates simulation results for the same system

but with a five-leg Yg -Yg transformer. Since there is no
voltage re-generation for the coil with lost phase, voltage
on the corresponding primary and secondary coils completely
collapse. Unlike three-core Yg -Yg or Yg - transformers that
continue to supply power to all three phases on the secondary
here five-core Yg -Yg transformer delivers 23 of the original
power on two of the phases. There is no increase in transformer
currents while low and high side currents and voltages of
the remaining phases are essentially unchanged. Low side
system is completely unbalanced with basic voltage or current
protection elements detecting a fault.

As discussed in Section III-B1 low side voltages or currents

may not be always helpful in detecting a fault upon loss of
a phase particularly in lower loading levels. After open phase
condition the high side currents are highly unbalanced with
one phase having no current and therefore negative and zero
sequence components are involved in the high side currents.
If we are to construct the high side currents from the low side
CTs we need to have these primary components available.
Of particular importance is the primary side zero sequence
current, I0Y , which is not actually available on the low side
as all zero sequence components are circulating inside the
winding. However, using the neutral CT of the Yg side of the
transformer can solve the issue of I0Y . In most installations
this neutral CT is available to detect ground faults on the high
side. The neutral CT has voltage insulation level much lower
than the phase CTs and hence should be a low cost CT.

IV. P ROTECTION A LGORITHMS FOR O PEN P HASE

C ONDITIONS IN T RANSFORMERS
We saw that generally a transformers response to an open
phase on the high side can be categorized as one of the three
cases we discussed: 1) Yg - transformers in which lost phase
is always re-generated, 2) transformers with or ungrounded
Y primaries in which the lost voltage is never re-generated,
and 3) Yg -Yg transformers that the response depends on the
core construction. The examination of these cases has provided
some key characteristics and aspects of each category that can
be used to develop new protection algorithms specific to open
phase conditions in transformers. The assumption is that there
are no phase CTs or PTs on the high side of the transformer.
We now examine each category for a protection algorithm.

Fig. 20.

Yg - Transformer with D1 Secondary Winding

Figure 20 illustrates a Yg - transformer with winding configured as D1 where it lags the Y side by 30
if system sequence is ABC. With transformers ratio being
V nom.
n = | VAB
| the current ratio is: IIba
= IIcb
= IIac
= n3 .
A
B
C
abnom.
Using mathematical characteristics of fractions we will have:

11

n
3I0
n
Iba + Icb + Iac
=
=
(16)
IA + IB + IC
IG
3
3
Where I0 is the circulating zero sequence current inside
winding and IG is the measured ground current by the
high side neutral current transformer. Therefore I0 can be
calculated in the following equation:
1
n
(17)
I0 = I0Y = nIG
3
3 3
In Figure 20 we have the following set of equations for the
low side currents of the transformer:

Fig. 21.

Yg - Transformer with D11 Secondary Winding

The following set of equations applies to the side currents,

where I0 is from the neutral CT as per equation 17.

Ia = Iba Iac
Ib = Icb Iba
Ic = Iac Icb

(18)

Ia = Ica Iab

Iba + Iac + Icb = 3I0

Ib = Iab Ibc

Ia + Ib + Ic = 0
In the above set of equations Ia , Ib and Ic are available from
the low side phase CTs and I0 is available from equation 17
which comes from the neutral CT of the Yg side. We can now
solve the set of equations in (18) to obtain Iba , Icb and Iac .
By doing so the coil currents of the winding are:
1
(Ia Ib ) + I0
3
1
Icb = (Ib Ic ) + I0
(19)
3
1
Iac = (Ic Ia ) + I0
3
Then high side currents of the transformer are obtained by
V nom.
simply applying the transformer ratio, n = | VAB
|, to the
abnom.
currents which leads us to the following set of equations:
Iba =

3
Iba
n

3
IB =
Icb
(20)
n
3
IC =
Iac
n
Equations 19 and 20 provide primary side currents in a
Yg - transformer in any conditions and loading level as
long as there is no internal fault to the transformer. While
external faults dont violate these equations an internal fault
in the transformer can make the equations invalid. In our
application of open phase condition by using these equations
we can identify an open phase by observing that one of the
phase currents of the high side is zero. Considering the CTs
inaccuracy we may declare an open phase when one of the
currents obtained from equation 20 is much below the other
two phases while currents on the low side of the transformer
appear to be highly balanced.
One other way of connecting three coils in a winding is
illustrated in Figure 21. In this configuration side leads the
Y side by 30 if system sequence is ABC and is called D11.
IA =

Ic = Ibc Ica

(21)

Iab + Ica + Ibc = 3I0

Ia + Ib + Ic = 0
Solving (21) for Iab , Ibc and Ica we obtain:
1
(Ib Ia ) + I0
3
1
Ibc = (Ic Ib ) + I0
3
1
Ica = (Ia Ic ) + I0
3
Iab =

(22)

The high side currents are then:

3
Ica
n
3
Iab
IB =
n

3
IC =
Ibc
n
IA =

(23)

Equations 22 and 23 provide high side currents of a Yg -

transformer with winding configuration of Figure 21. Again,
these equations are true for any transformer conditions, except
for transformers internal faults, that can be used to identify
an open phase on the primary side of the transformer when
one of the phase currents are calculated as being zero or close
to zero in comparison to the other two phases.
The equations and algorithm presented here are applicable
to any transformer physical construction or any transformer
loading conditions and also in DG cases where there is a
generating source on the low side exporting power to the grid.
In DG applications the flow of power will be opposite to when
there is only load on the low side and the direction of all
primary and secondary currents in Figures 20 and 21 will
reverse. However, by maintaining the same CT connections
as in the non-DG cases discussed here all equations presented
in this Section are directly applicable to DG as well.

12

Figure 22 illustrates simulation results for the same system

of Section III-B1 with 60KW load on the transformer. Recall
from Figure 11 that due to the very small load on the
transformer the low side voltages and currents were highly
balanced after open phase condition. Figure 22 shows primary
side currents, IA , IB and IC , both as measured from the high
side and calculated from the low side using equations 19 and
20. Based on the high side calculated currents the protection
algorithm can identify an open phase on phase A on the high
side.
In addition to the inherent CT inaccuracies there are two
other sources of inaccuracies for the calculated high side
currents, although not expected to have considerable impact.
First is the fact that, as described in III-B1, the low side
coil with lost phase carry a small current for magnetization
and core losses. This current will result in the calculation to
provide a very small current for the lost phase on the primary
side as may be recognizable in Figure 22. The second one
is the transformers magnetizing and core losses current as
supplied by the high side grid. This current, which is modeled
as the parallel branch in the transformer equivalent circuit, will
not be considered in the calculations of primary currents.

of core construction and low side winding configuration as

long as the primary side is or Y . Hence Table A provides a
practical, reliable and simple tool for identification and protection of open phase conditions in these types of transformers.
All values in Table A are true for DG cases and it is directly
applicable to DG where there is a power generating source on
the low side exporting to the grid.
Another method to identify an open phase in transformers
with ungrounded primary winding is to calculate the high side
currents from the low side CTs, similar to the concept used in
Yg - transformers. However, since no zero sequence current is
flowing from the primary to the secondary side the calculations
will be much less complicated. Note that, where the low side
is a Yg configuration, there could be zero sequence current on
the low side which will induce an I0 inside the winding.

Transformer LV Currents- Ia, Ib, Ic

80

Amp.

Fig. 23.

Currents in a -Yg Transformer with D1 Primary

75

Calculation of the high side line currents from the low

side CTs for a -Yg transformer is provided as an example
with the transformer illustrated in Figure 23. The following
set of equations apply to the currents in Figure 23, where
V nom.
transformers ratio is n = | VAB
|.
ab

70
Transformer Measured HV Currents- IA, IB, IC

Amp.

6
4

nom.

1
ICA = Ic
n 3
1
IBC = Ib
n 3
1
IAB = Ia
n 3

0
Transformer Calculated HV Currents- IA, IB, IC
6
4
2
0

0.05

0.1
Time (Sec)

0.15

(24)

0.2

Fig. 22. Simulation Results for Measured and Calculated Primary Currents
in a Yg - Transformer After Loss of Phase A- Load=60KW

With ICA , IBC and IAB obtained from (24) we can now
calculate the primary side line currents per below:
IA = IAB ICA

B. Transformers with Ungrounded Primary ( or Y )

As discussed in Section III-B2 transformers with ungrounded primary winding will have major unbalance conditions upon loss of a phase such that voltage or current
protection elements on the low side will detect a fault. However, those protection elements do not necessarily provide the
actual cause of the fault without which the down time for
investigation and finding the open phase on the primary side
could be further extended.
One algorithm to identify an open phase condition in such
transformers was developed in III-B2 where values of II21 on
the low side for various open phase conditions are provided in
Table A. These values are consistent and applicable regardless

IB = IBC IAB

(25)

IC = ICA IBC
The above set of equations are true whether or not there is
zero sequence current on the low side (Yg ), for instance in case
of an unbalance load. This is because any I0 on the low side
will be considered in the high side coils by equation 24,
although I0 will be cancelled out in line currents by (25).
Figure 24 illustrates simulation results for the same system
in Section III-B2 with an unbalanced total load of 100KW.
Note that the unbalanced load creates zero sequence current
on the low side which will be circulating inside the winding
coils. The calculated primary side currents identify that phase
A is open.

13

The coils may also be connected in a different way

as shown in Figure 25 which will create a phase angle
shift opposite to the previous example. The following set of
equations applies to the transformer currents:
1
ICB = Ic
n 3
1
IBA = Ib
n 3
1
IAC = Ia
n 3

(26)
Fig. 25.

The primary side line currents can then be calculated as

below, which will identify an open phase condition when one
of the currents is calculated as zero.

IA = IAC IBA
IB = IBA ICB

(27)

IC = ICB IAC

Transformer LV Currents- Ia, Ib, Ic

Transformer LV Sequence Currents- I1, I2, I0

160

160

120
Amp.

Amp.

120
80

80
40

40

4
Amp.

Transformer Calculated HV Currents- IA, IB, IC

6

Amp.

Transformer Measured HV Currents- IA, IB, IC

6

0.05

0.1
Time (Sec)

0.15

0.2

0.05

0.1
Time (Sec)

0.15

0.2

Fig. 24. Simulation Results for Measured and Calculated Primary Currents
in a -Yg Transformer After Loss of Phase A- Unbalanced Load=100KW

With similar exercise primary side currents can be calculated from the low side CTs in other less commonly used
transformers such as Y -Yg or - which are not presented
here to stay focused on the commonly used transformers. This
method of calculating the high side current is also true and
applicable in DG cases with direct use of the above equations.
In summary, there are two reliable and effective methods
for identification and protection of open phase conditions in
transformers with or ungrounded Y primary winding: the
method of II21 values of the low side and the method of high
side current calculation. These methods may be combined
as a single algorithm to provide a robust and effective way
to identify an open phase condition in transformers with
ungrounded primary.

Currents in a -Yg Transformer with D11 Primary

C. Yg -Yg Transformers
Although Yg -Yg transformers demonstrate different characteristics in open phase conditions depending on the core type
the principle of calculating the high side currents from the
low side CTs provides a general method for identification
and protection of open phase conditions in Yg -Yg transformers
regardless of the physical construction.
Figure 26 illustrates a Yg -Yg transformer with one phase
open. Positive and negative sequence currents of the transformers primary and secondary are still governed by the
transformer ratio in the new unbalanced system after loss of
V nom.
| we will have :
a phase. If n = | VAB
ab
nom.

I1Sec.
I2
= Sec. = n
(28)
I1P ri.
I2P ri.
However, the above is not necessarily true for the zero sequence currents in three-leg core transformers. Zero sequence
magnetizing current and core losses in three-leg cores are
significantly larger than that of a positive sequence model.
Therefore, the parallel branch in the transformers zero sequence model has more considerable impact, i.e. the current
in the parallel branch may not be totally ignored. Hence I0 of
the two sides will have a ratio different than n. Furthermore,
upon loss of a phase in a three-leg transformer, the primary
side has only two phases with very high I0 (IG = IB + IC ).
However, a large portion of this zero sequence current flows in
the parallel branch for zero sequence magnetization and core
loss and a small portion will be induced in the secondary side.
The secondary side is still a three-phase system with much
smaller I0 , although not necessarily highly balanced depending
on the load size. Therefore each side will have a different I0
that can freely circulate in each grounded side.

Fig. 26.

Currents in a Yg -Yg Transformer

The reliable source of the high side zero sequence current,

I0P ri. , is again the neutral CT on the primary side of the

14

transformer. If the high side ground current is IG , as measured

by the neutral CT in Figure 26, then we have:
1
(29)
I0P ri. = IG
3
With I1Sec. and I2Sec. calculated from the low side CT
measurements, I1P ri. and I2P ri. are then obtained from (28).
With I0P ri. from (29) all symmetrical components of the
primary currents are now available and IA , IB , and IC can
be easily computed. Note that there is no phase shift between
primary and secondary sides of the transformer.
The above method for identification and protection of open
phase conditions is valid regardless of the transformer physical
construction, although Yg -Yg transformers will have different
responses to loss of a phase depending on the core type. Using
the equations provided in this section the primary side currents
are calculated and an open phase will be detected. Besides, it
is directly applicable to DG where a power generation source
on the secondary side exports power to the grid.
Figure 27 illustrates simulation results for the same system
of Figure 10 with a three-leg core Yg -Yg transformer. It
is assumed that the transformers zero sequence no load
magnetizing current is 1pu with a corresponding core losses of
20KW . Before the loss of phase A at t = 0.1Sec. transformer
is loaded at 120KW .
Transformer LV Currents- Ia, Ib, Ic

Transformer Measured HV Currents- IA, IB, IC

15

160

Amp.

Amp.

10
140

120

HV and LV Zero Sequence Currents

Transformer Calculated HV Currents- IA, IB, IC

15

Amp.

Amp.

10
5

0.05

0.1
Time (Sec)

0.15

0.2

Open phase conditions in three-phase transformers present a

challenge for power system operation and protection, particularly in distribution networks. With more Distributed Generation deployed the challenge can become more complicated.
Proper and effective identification and protection methods
help improve the power system reliability and performance.
This paper discussed that how and why standard or traditional protection elements cannot always detect an open phase
in transformers, particularly in lower loadings. Three major
transformer configurations were identified with each group
responding differently to loss of a phase. In fact different
electrical or magnetic mechanisms are at work in each of the
three transformer groups upon loss of a single phase. While in
transformers with ungrounded primary winding there will be
substantial unbalance conditions with one phase open on the
high side in transformers with Yg primary the system may still
be fairly balanced on the low side. For each group of transformers a method was developed for effective identification of
the lost phase and therefore protection of the transformer upon
open phase conditions. Hence a protection algorithm can be
established to address open phase conditions in each group of
transformers. The presented methods are universally applicable
to DG cases as well where a power generating source on the
low side of the transformer exports power to the grid. Digital
simulation was performed for several types of transformers to
illustrate a transformers response to an open phase as well
as to demonstrate the operation of the protection methods
presented in this paper.
R EFERENCES

10

V. C ONCLUSION

0.05

0.1
Time (Sec)

0.15

0.2

[1] A.E. Fitzgerald, C. Kingsley Jr. and S.D. Umans, Electric Machinery,
4th ed. McGraw-Hill, 1983.
[2] Stephen J. Chapman, Electric Machinery Fundamentals, 4th ed.
McGraw-Hill, 2005.
[3] J. Lewis Blackburn, Thomas J. Domin, Protective Relaying- Principles
and Applications, 3rd ed. CRC Press, 2006.
[4] John Horak and Gerald F. Johnson, A Practical Guide for Detecting
Single-Phasing on a Three-Phase Power System, Western Protective
Relay Conference, 2002.
[5] Jialong Wang and Raluca Lascu, Zero Sequence Circuit of Three-legged
Core Type Transformers. (Basler Electric)
[6] E. L Harder, Sequence Network Connections for Unbalanced Load and
Fault Conditions, The Electric Journal, December 1937.
[7] Paul M. Anderson, Analysis of Faulted Power Systems, IEEE Press,
1995.

Fig. 27. Simulation Results for Measured and Calculated Primary Currents
in a Three-leg core Yg -Yg Transformer After Loss of Phase A- Load=120KW

After open phase condition the low side is fairly balanced

I
with I12Sec. = 7.4%. Note to the zero sequence currents that
Sec.
are not governed by the transformer ratio with I0P ri. = 5.49A
and I0Sec. = 9.65A. Regardless of the core type the method
will accurately calculate the high side currents from the low
side and neutral CTs, although in four/five leg core type or
bank of three single phase transformers the low side will not
be balanced with one phase completely lost. Besides, in those
types of transformers the turn ratio is actually applicable to
I0P ri. and I0Sec. . Here the magnetization and core loss currents
in the parallel branch of the transformers zero sequence model
are not different from positive or negative sequence models.

Amir Norouzi received his B.Sc degree from Tehran Polytechnic in 1996
and his M.Sc from the University of New Brunswick, NB, in 2003 both in
electrical engineering. He has over 13 years of experience in power system
engineering including substations, industrial applications, power generation
and distribution. He joined GE Digital Energy in Markham, Ontario, in 2011
as a technical application engineer, focusing on providing system solutions in
protection and control.
Presented at MIPSYCON 2013
Previously Presented at 2012 WPRC and Georgia Tech 2013.