FL PDF

ENGINE
SECTION
FL
FUEL SYSTEM
FL
CONTENTS
PRECAUTION ............................................... 2
EVAP CANISTER .............................................. 12
PRECAUTIONS ................................................... 2
Exploded View .........................................................12

Removal and Installation .........................................12
Inspection ................................................................13
Precaution for Supplemental Restraint System

(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ................................................................... 2
General Precautions ................................................. 2
PREPARATION ............................................ 3
PREPARATION ................................................... 3
EVAP CANISTER FILTER ................................ 14

Exploded View .........................................................14
EVAP CANISTER VENT CONTROL VALVE ... 15

Exploded View .........................................................15
PERIODIC MAINTENANCE .......................... 4
EVAP CONTROL SYSTEM PRESSURE SENSOR ................................................................... 16
FUEL SYSTEM .................................................... 4
Exploded View .........................................................16

Special Service Tool ................................................. 3

Commercial Service Tools ........................................ 3
Inspection .................................................................. 4
Quick Connector ....................................................... 4
UNIT DISASSEMBLY AND ASSEMBLY ... 17
REMOVAL AND INSTALLATION ................ 5
FUEL LEVEL SENSOR UNIT ........................... 17
FUEL LEVEL SENSOR UNIT, FUEL FILTER

AND FUEL PUMP ASSEMBLY .......................... 5
Exploded View .......................................................... 5
Removal and Installation ........................................... 5
FUEL TANK ......................................................... 9

Exploded View .......................................................... 9
Removal and Installation ........................................... 9
Inspection ................................................................ 11
Disassembly and Assembly .....................................17
SERVICE DATA AND SPECIFICATIONS

(SDS) ............................................................ 19
SERVICE DATA AND SPECIFICATIONS

(SDS) ................................................................. 19
Fuel Tank .................................................................19
Revision: April 2013
FL-1
2014 Versa Sedan
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009267696
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
General Precautions
INFOID:0000000009267697
WARNING:
When replacing fuel line parts, be sure to observe the following.
Put a CAUTION: FLAMMABLE sign in the workshop.
Be sure to work in a well ventilated area and furnish workshop with a CO2 fire extinguisher.
Do not smoke while servicing fuel system. Keep open flames and sparks away from the work area.
CAUTION:
Use gasoline required by the regulations for octane number. Refer to GI-33, "Fuel (Regular Unleaded
Gasoline Recommended) HR16DE".
Before removing fuel line parts, perform the following procedures:
- Put drained fuel in an explosion-proof container and put the lid on securely. Keep the container in
safe area.
- Release fuel pressure from the fuel lines. Refer to EC-133, "Work Procedure".
- Disconnect the battery cable from the negative terminal.
Always replace O-ring and clamps with new ones.
Do not kink or twist tubes when they are being installed.
Do not tighten hose clamps excessively to avoid damaging hoses.
After installing tubes, check there is no fuel leakage at connections in the following steps.
- Apply fuel pressure to fuel lines with turning ignition switch ON (with engine stopped). Then check
for fuel leakage at connections.
- Start engine and rev it up and check for fuel leakage at connections.
Use only a Genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the
MIL may come on.
For servicing EVAPORATIVE EMISSION SYSTEM parts, refer to EC-41, "EVAPORATIVE EMISSION
SYSTEM : System Diagram".
FL-2
2014 Versa Sedan
PREPARATION
< PREPARATION >
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009267698
FL
The actual shapes of Kent-Moore tools may differ from those of special tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV10119900
(J-45722)
Lock ring wrench
Removing and Installing lock ring
E
JPBIA3555ZZ
Commercial Service Tools
INFOID:0000000009267699
Tool name
Description
Power tools
Loosening nuts, screws and bolts
I
PIIB1407E
FL-3
2014 Versa Sedan
FUEL SYSTEM
< PERIODIC MAINTENANCE >
PERIODIC MAINTENANCE
FUEL SYSTEM
Inspection
INFOID:0000000009267700
Inspect fuel lines, fuel filler cap, and fuel tank for improper attachment, leakage, cracks, damage, loose connections, chafing or deterioration.
(A)
: Engine
(B)
: Fuel line
(C)
: Fuel tank
If necessary, repair or replace damaged parts.

JPBIA0129ZZ
Quick Connector
INFOID:0000000009267701
CAUTION:
After connecting fuel tube quick connectors, check quick connectors are secure.
Ensure that connector and resin tube do not contact any adjacent parts.
FL-4
2014 Versa Sedan
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION

Exploded View
INFOID:0000000009267702
FL
G
JPBIA4501GB
1.
Lock ring
4.
Fuel tank
2.
Fuel level sensor unit, fuel filter and

fuel pump assembly
3.
Removal and Installation
INFOID:0000000009267703
WARNING:
Be sure to read General Precautions before working on the fuel system. Refer to FL-2, "General Precautions".
REMOVAL
1.
2.
Release the fuel pressure from the fuel lines. Refer to EC-133, "Work Procedure".
Check fuel level with vehicle on a level surface. If the fuel level is 7/8 of the fuel tank (full or nearly full),
draw appropriate amount of fuel from the fuel tank.
Guideline
3.
4.
5.
6.
O-ring
: Draw approximately 10 liters (2-5/8 US gal, 2-1/4 Imp gal) from a full-tank condition.
In the event of malfunction in fuel pump, insert a hose measuring 20 mm (0.79 in) in diameter into the
filler opening to draw approximately 10 liters (2-5/8 US gal, 2-1/4 Imp gal) fuel.
Open fuel filler lid.
Open fuel filler cap and release the pressure inside fuel tank.
Remove the rear seat cushion. Refer to SE-23, "Removal and Installation - Seat Cushion Assembly".
Remove the inspection hole cover.
FL-5
2014 Versa Sedan
7. Disconnect the harness connector (B), fuel feed tube (C) and
EVAP tube (A).
: Front
ALBIA0747ZZ
Remove the quick connector as follows:

Hold the sides of the connector, push in tabs (B) and pull (A)
out the tube.
If the connector and the tube are stuck together, push and pull
several times until they start to move. Then disconnect them
by pulling.
JPBIA0134ZZ
CAUTION:
The tube can be removed when the tabs are completely depressed. Do not twist it more than
necessary.
Do not use any tools to remove the quick connector.
Keep the resin tube away from heat. Be especially careful when welding near the tube.
Prevent acid liquid such as battery electrolyte, etc. from getting on the resin tube.
Do not bend or twist the tube during installation and removal.
Only when the tube is replaced, remove the remaining retainer on the tube or fuel level sensor,
fuel filter, and fuel pump assembly.
When the tube or fuel level sensor, fuel filter, and fuel pump assembly is replaced, also replace
the retainer with a new one (green colored retainer).
To keep the connecting portion clean and to avoid damage and foreign materials, cover them completely with
plastic bags (B) or something similar.
(A)
: Fuel feed hose
(C)
: Fuel tube
JSBIA1295ZZ
8.
Remove the lock ring using Tool (A).

Tool number
: KV10119900 (J-45722)
NOTE:
For reference when installing, put a matching mark on lock ring,
fuel pump assembly and fuel tank.
JPBIA3556ZZ
FL-6
2014 Versa Sedan
9. Remove fuel level sensor unit, fuel filter and fuel pump assembly. Remove and discard the O-ring.
CAUTION:
Do not bend the float arm during removal.
Do not reuse O-ring.
INSPECTION AFTER REMOVAL
FL
Inspect the fuel level sensor, fuel filter, and fuel pump assembly for any defects and foreign materials. Replace
as necessary.
INSTALLATION
Installation is in the reverse order of removal.

Install the fuel level sensor, fuel filter, and fuel pump assembly with
the fuel feed tube (C) facing the front of the vehicle as shown. Use
a new O-ring.
CAUTION:
: Front
(A)
: EVAP tube
(B)
: Harness connector
F
ALBIA0747ZZ
Install the lock ring using Tool (A).

Tool number
: KV10119900 (J-45722)
NOTE:
For reference when installing, align the matching marks on lock
ring, fuel pump assembly and fuel tank.
Connect the quick connector as follows:

- Check the connection for damage or any foreign materials.
- Align the connector with the tube, then insert the connector straight
into the tube until a click is heard.
After the tube is connected, make sure the connection is secure by
performing the following checks:
- Pull (A) the tube and the connector to make sure they are securely
connected.
JPBIA3556ZZ
M
JPBIA0140ZZ
FL-7
2014 Versa Sedan
- Visually confirm that the two retainer tabs are connected to the
quick connector.
PBIC0199E
FL-8
2014 Versa Sedan
FUEL TANK
FUEL TANK
Exploded View
INFOID:0000000009267704
FL
I
JPBIA3365GB
1.
Fuel tank
2.
Fuel tank mounting band (RH)
3.
Fuel tank mounting band (LH)
4.
Clamp
5.
Fuel filler hose
6.
Fuel filler tube
7.
Grommet
8.
Fuel filler cap
9.
Clamp
10. Vent hose
INFOID:0000000009267705
WARNING:
Be sure to read General Precautions before working on the fuel system. Refer to FL-2, "General Precautions".
REMOVAL
1.
2.
Release the fuel pressure from the fuel lines. Refer to EC-133, "Work Procedure".
Check fuel level with vehicle on a level surface. If the fuel level is 7/8 of the fuel tank (full or nearly full),
draw appropriate amount of fuel from the fuel tank.
Guideline
3.
4.
5.
6.
: Draw approximately 10 liters (2-5/8 US gal, 2-1/4 imp gal) from a full-tank condition.
In the event of malfunction in fuel pump, insert a hose measuring 20mm (0.79 in) in diameter into the
filler opening to draw approximately 10 liters (2-5/8 US gal, 2-1/4 Imp gal) fuel.
Open fuel filler lid.
Open fuel filler cap and release the pressure inside fuel tank.
Remove the rear seat cushion. Refer to SE-23, "Removal and Installation - Seat Cushion Assembly".
Remove the inspection hole cover.
FL-9
2014 Versa Sedan
FUEL TANK
7. Disconnect the harness connector (B), fuel feed tube (C) and
EVAP tube (A).
: Front
ALBIA0747ZZ
Remove the quick connector as follows:

Hold the sides of the connector, push in tabs (B) and pull (A)
out the tube.
If the connector and the tube are stuck together, push and pull
several times until they start to move. Then disconnect them
by pulling.
JPBIA0134ZZ
CAUTION:
The tube can be removed when the tabs are completely depressed. Do not twist it more than
necessary.
Do not use any tools to remove the quick connector.
Keep the resin tube away from heat. Be especially careful when welding near the tube.
Prevent acid liquid such as battery electrolyte, etc. from getting on the resin tube.
Do not bend or twist the tube during installation and removal.
Only when the tube is replaced, remove the remaining retainer on the tube or fuel level sensor,
fuel filter, and fuel pump assembly.
When the tube or fuel level sensor, fuel filter, and fuel pump assembly is replaced, also replace
the retainer with a new one (green colored retainer).
To keep the connecting portion clean and to avoid damage and foreign materials, cover them completely with
plastic bags (B) or something similar.
(A)
: Fuel feed hose
(C)
: Fuel tube
JSBIA1295ZZ
8. Remove center muffler and main muffler. Refer to EX-5, "Exploded View".
9. Disconnect the LH rear park brake cable brackets. Refer to PB-6, "Exploded View".
10. Remove the rear floor insulator located above center and main mufflers.
FL-10
2014 Versa Sedan
FUEL TANK
11. Disconnect fuel filler hose at fuel filler tube side.
A
(1)
: Fuel filler tube
(2)
: Fuel filler hose
(3)
: Vent hose
FL
12. Disconnect vent hose from fuel tank side.

C
JPBIA3423ZZ
13. Support the center part of fuel tank (1) using a suitable jack (A).
G
JPBIA3424ZZ
14. Remove fuel tank mounting bands (LH/RH).

15. Lower transmission jack carefully to remove fuel tank while holding it by hand.
CAUTION:
Fuel tank may be in an unstable condition because of the shape of fuel tank bottom. Be sure to
hold tank securely.
INSTALLATION
Fuel Filler Hose

Insert fuel filler hose to the length below.
Fuel filler hose

The other hose
: 35 mm (1.38 in)
: 25 mm (0.98 in)
Be sure hose clamp is not placed on swelled area of fuel filler tube.
Install fuel filler hose to fuel tank, paying attention to install mark.
Tighten fuel filler hose clamp so that the remaining length of screw thread becomes to the following.
Fuel tank side hose clamp
Fuel filler tube side hose clamp
: 7 - 11 mm (0.28 - 0.43 in)

: 8 - 12mm (0.31 - 0.47 in)
EVAP Hose
1.
2.
Check connections for damage or foreign material.

Align the matching side connection part with the center of shaft, and insert connector straight until a "click"
sound is heard.
Inspection
INFOID:0000000009267706
INSPECTION AFTER INSTALLATION

Use the following procedure to check for fuel leakage.
1. Turn ignition switch ON (with engine stopped), and check connections for leakage by applying fuel pressure to fuel piping.
2. Start engine and rev it up and check there are no fuel leakage at the fuel system tube and hose connections.
FL-11
2014 Versa Sedan
EVAP CANISTER
EVAP CANISTER
Exploded View
INFOID:0000000009267707
ALBIA0750ZZ
1.
EVAP control system pressure sensor 2.
O-ring
3.
EVAP canister
4.
Hose clamp
5.
EVAP canister purge hose
6.
EVAP vent line
7.
O-ring
8.
EVAP canister vent control valve
9.

hose
A.
Mount to vehicle bracket
INFOID:0000000009267708
NOTE:
The EVAP canister vent control valve and EVAP canister system pressure sensor can be removed without
removing the EVAP canister.
REMOVAL
1.
2.
3.
4.
5.
Remove the EVAP canister protector cover.

Disconnect the harness connectors from the EVAP control system pressure sensor and the EVAP canister vent control valve.
Disconnect the EVAP canister purge hose, the EVAP vent line, and the EVAP canister vent control valve
hose.
Remove the EVAP canister bolt.
Remove the EVAP canister from the vehicle.
INSTALLATION
CAUTION:
FL-12
2014 Versa Sedan
EVAP CANISTER
Do not reuse O-rings.
A
Inspection
INFOID:0000000009267709
Check EVAP canister as follows:

1. Block port (B).
2. Blow air into port (A) and check that it flows freely out of port (C).
3. Release blocked port (B).
4. Apply vacuum pressure to port (B) and check that vacuum pressure exists at the ports (A) and (C).
5. Block port (A) and (B).
6. Apply pressure to port (C) and check that there is no leakage.
FL
D
PBIB1212E
FL-13
2014 Versa Sedan
EVAP CANISTER FILTER

EVAP CANISTER FILTER

Exploded View
INFOID:0000000009267710
ALBIA0751ZZ
1.
EVAP canister vent control valve hose
2.
Canister drain hose
3.
EVAP canister filter
Front
INFOID:0000000009267711
REMOVAL
1.
2.
3.
4.

Disconnect EVAP canister vent control valve hose from EVAP canister filter.
Disconnect canister drain hose from EVAP canister filter.
Remove the bolt and the EVAP canister filter.
INSTALLATION
FL-14
2014 Versa Sedan
EVAP CANISTER VENT CONTROL VALVE

EVAP CANISTER VENT CONTROL VALVE
Exploded View
INFOID:0000000009267712
FL
G
ALBIA0752ZZ
1.
EVAP canister
4.
EVAP canister vent control valve hose
2.
O-ring
3.
INFOID:0000000009267713
NOTE:
The EVAP canister vent control valve can be removed without removing the EVAP canister.
REMOVAL
1.
2.
3.
4.
5.

Disconnect EVAP canister vent control valve hose from EVAP canister.
Disconnect the harness connector from the EVAP canister vent control valve.
Turn EVAP canister vent control valve counterclockwise.
(A)
: Lock
(B)
: Unlock
Remove the EVAP canister vent control valve and O-ring.

CAUTION:
N
PBIB3091E
INSTALLATION

CAUTION:
FL-15
2014 Versa Sedan
EVAP CONTROL SYSTEM PRESSURE SENSOR

EVAP CONTROL SYSTEM PRESSURE SENSOR

Exploded View
INFOID:0000000009267714
ALBIA0753ZZ
1.
EVAP control system pressure sensor 2.
O-ring
3.
EVAP canister
INFOID:0000000009267715
NOTE:
The EVAP canister system pressure sensor can be removed without removing the EVAP canister.
REMOVAL
1.
2.
3.
4.

Disconnect EVAP canister purge hose from EVAP canister.
Disconnect EVAP control system pressure sensor.
Remove EVAP control system pressure sensor and O-ring.
CAUTION:
INSTALLATION
CAUTION:
FL-16
2014 Versa Sedan
FUEL LEVEL SENSOR UNIT

< UNIT DISASSEMBLY AND ASSEMBLY >
UNIT DISASSEMBLY AND ASSEMBLY

Disassembly and Assembly
INFOID:0000000009267716
FL
Fuel Level Sender Unit

C
ALBIA0748ZZ
1.
Harness connectors
4.
Float arm assembly
2.
Level sending unit module
3.
Fuel temperature sensor
Disassembly
NOTE:
Before disassembly, note the proper placement of the wires to the correct terminals and correct wire routing to
the terminals.
1. Disconnect the red, white, and double black wire connectors.
FL-17
2014 Versa Sedan

< UNIT DISASSEMBLY AND ASSEMBLY >
Press the tabs on the terminals to release the locking tabs.
ALBIA0669ZZ
2.
Release the two clips and remove the fuel temperature sensor
from the pump assembly.
ALBIA0670ZZ
3.
Release the tab (A) and slide the level sending unit module and
float arm assembly up (B) to remove.
ALBIA0749ZZ
Assembly
Assembly is in the reverse order of disassembly.
NOTE:
Ensure proper placement of the wires to the correct terminals and correct wire routing to the terminals.
After connecting terminals, ensure they are securely locked and can not be pulled out.
When installing the level sending unit, push down until the tab is locked into place.
FL-18
2014 Versa Sedan
SERVICE DATA AND SPECIFICATIONS (SDS)

< SERVICE DATA AND SPECIFICATIONS (SDS)

Fuel Tank
INFOID:0000000009267717
FL
STANDARD AND LIMIT

C
Fuel tank capacity

Fuel recommendation
Approx. 41.0
(10-7/8 US gal, 9 Imp gal)
Refer to GI-33, "Fuel (Regular Unleaded Gasoline Recommended)

HR16DE".
FL-19
2014 Versa Sedan

FL PDF

Uploaded by

Copyright:

Available Formats

FL PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FL PDF

Uploaded by

Copyright:

Available Formats

ENGINE

EVAP CANISTER .............................................. 12

Exploded View .........................................................12

Precaution for Supplemental Restraint System

EVAP CANISTER FILTER ................................ 14

EVAP CANISTER VENT CONTROL VALVE ... 15

PERIODIC MAINTENANCE .......................... 4

EVAP CONTROL SYSTEM PRESSURE SENSOR ................................................................... 16

FUEL SYSTEM .................................................... 4

Exploded View .........................................................16

Special Service Tool ................................................. 3

UNIT DISASSEMBLY AND ASSEMBLY ... 17

REMOVAL AND INSTALLATION ................ 5

FUEL LEVEL SENSOR UNIT ........................... 17

FUEL LEVEL SENSOR UNIT, FUEL FILTER

FUEL TANK ......................................................... 9

Disassembly and Assembly .....................................17

SERVICE DATA AND SPECIFICATIONS

SERVICE DATA AND SPECIFICATIONS

Revision: April 2013

2014 Versa Sedan

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

2014 Versa Sedan

Removing and Installing lock ring

Commercial Service Tools

Loosening nuts, screws and bolts

Revision: April 2013

2014 Versa Sedan

If necessary, repair or replace damaged parts.

Revision: April 2013

2014 Versa Sedan

REMOVAL AND INSTALLATION

Fuel level sensor unit, fuel filter and

Removal and Installation

Revision: April 2013

2014 Versa Sedan

Remove the quick connector as follows:

: Fuel feed hose

Remove the lock ring using Tool (A).

Revision: April 2013

2014 Versa Sedan

INSPECTION AFTER REMOVAL

Installation is in the reverse order of removal.

Install the lock ring using Tool (A).

Connect the quick connector as follows:

Revision: April 2013

2014 Versa Sedan

Revision: April 2013

2014 Versa Sedan

Fuel tank mounting band (RH)

Fuel tank mounting band (LH)

Fuel filler hose

Fuel filler tube

Fuel filler cap

10. Vent hose

Removal and Installation

Revision: April 2013

2014 Versa Sedan

Remove the quick connector as follows: