ELECTRONIC CONTROL UNIT

LRX 2102R ++

GB

Single-phase electronic control unit for the automation of

sliding gates with incorporated radio receiver.
- Mod. LG 2102R ++
- Mod. (LRQ 2102R ++ )
- Mod. (LR 2102R ++ )
- Mod. (LR 2102R ++ / 330 )
- Mod. (LR 2102R ++ / 418 )
- Mod. LRS 2102R ++
- Mod. LRS 2102R ++ SET
- Mod. LRH 2102R ++

: Without radio receiver

: 30.875 Mhz
: 306 Mhz
: 330 Mhz
: 418 Mhz
: 433.92 Mhz
: 433.92 Mhz narrow band
: 868.3 Mhz narrow band

( ) Product intended for those countries where its use is

permitted
TECHNICAL DATA:
- Power supply
: 230 V ac 50-60Hz 1100W max.
- Flashing beacon output
: 230 V ac 500 W max.
- Motor output
: 230 V ac 500 W max.
- Auxiliary power output
: 24 V a/c 3 W max.
- Stop limit and low voltage commands : 24 V cc
- Working temperature
: -10 55 C
- Radio receiver
: see model
- Op. transmitters
: 12-18 Bit or Rolling Code
- Max stored TX codes
: 215 (CODE + CODE PED)
- Box dimensions
: 110x121x47 mm.
- Container
: ABS V-0 (IP54).
TERMINAL BOARD CONNECTIONS:
CN1:
1 : 230 V a/c line input (Phase).
2 : 230 V a/c line input (Neutral).
3 : 230 V a/c flashing line input (Neutral).
4 : 230 V a/c flashing line input (Phase).
5 : Opening motor output.
6 : Common motor output.
7 : Closing motor output.
CN2:
1 : Service power supply output 24 V a/c 3 W.
2 : Service power supply output 24 V a/c 3 W.
3 : Open-close command button input (NA).
4 : Common GND input.
5 : Safety device input (NC).
6 : Opening stop limit input (NC).
7 : Common GND input.
8 : Closing stop limit input (NC).
9 : Earth antenna input.
10: Antenna hot pole input.

FUNCTIONAL DATA:
Step-by-Step Operation:
Using both the radio control (CODE LED illuminated) and the
low voltage push-button station (PUL) to control the gate, the
following operation is obtained:
the first impulse opens the gate until the motor timer reaches
zero or until the opening stop limit is reached, the second
impulse closes the shutter; if an impulse arrives before the
opening stop limit is reached, the control unit stops motion
during both opening and closing. A futher command restarts
motion in the opposite direction.
Automatic closing:
The control unit can close the gate automatically without
sending additional commands.
The selection of this operation mode is described in the Pause
Time programming mode.

Pedestrian Passage:
If selected (PED CODE LED illuminated), using the pedestrian
radio control to control the gate, the following operation is
obtained: the first press is a command for the gate to open for
10 seconds, then the control unit pauses for 10 seconds and
the gate closes again.
Safety device:
The control unit enables power supply and connection for
photoelectric cells and pneumatic buffers (NC).
No action is taken into account during the opening stage and
causes inverted motor action during the closing stage.
If not used, this input must be bridged.
Initial pick-up and Motor Power Adjustment:
The electronic control unit is equipped with initial pick-up and
motor power adjustment functions that are fully managed by
the microprocessor.
The initial pick-up function is used to help the motor in its initial
activation stage, powering it at the maximum level for 2
seconds, even if the motor power adjustment function is
enabled.
The motor power adjustment function is used to ensure the
correct motion of the gate, blocking it in case of obstruction
without causing harm to individuals or their property.
Deceleration:
The motor deceleration function is used to avoid the gates
moving at high speed towards the end of the opening and
closing stages.
Deceleration can be programmed for the desired points (before
the gates are totally open or closed) during Motor Timer
programming.
Flashing Beacon Operation:
The control unit is equipped with output for a 230 V a/c flashing
beacon. The flashing beacon is only activated when the motor
is running.
Operation with TIMER:
The control unit may be connected to a timer instead of using
the open-close command button (PUL).
Example: at 8:00 a.m. the timer closes the contact and the
control unit opens the gate; at 6:00 p.m. the timer opens the
contact and the control unit closes the gate. Between 8:00 a.m.
and 6:00 p.m. at the end of the opening phase, the control unit
disables the flashing beacon, the automatic closing stage and
the radio controls.
PROGRAMMING:
SEL key: selects the type of function to be stored; selection is
indicated by a flashing LED.
By pressing the key repeatedly, you can select the desired
function.
The selection remains active for 10 seconds
(indicated by the flashing LED); after 10 seconds, the control
unit returns to its original status.
SET key: programmes the information according to the type of
function selected previously using the SEL key.
IMPORTANT: The function of the SET key can be replaced
with the radio control, if programmed previously (CODE LED
on).

MAIN MENU
The control unit is supplied by the manufacturer with the option
of selecting a number of principal functions.
---------------------- MAIN MENU ----------------LED Reference
1) CODE
2) CODE PED.

LED Off
No code
No code

LED On
Code inserted
Code inserted

3) INB.CMD.AP
Disabled
4) LAMP/CORT.
Flashing
5) T. MOT.
Programmed time 30 sec.
6) T. PAUSA.
No automatic closure

Enabled
Courtesy light
Programmed time
Automatic closure

1) CODE: (Radio control code)

The control unit can store up to 215 radio controls with
different fixed or rolling codes.
Programming.
To programme the transmission code, proceed as follows: use
the SEL key when the CODE LED is flashing and send the
desired code with the relevant radio control; programming has
been completed when the CODE LED remains lit constantly. If
you have stored 215 codes and you repeat the programming
operation, all the programming LEDs will start flashing to
indicate that no more codes can be stored.
Deleting the codes.
To delete all transmission codes stored in the memory,
proceed as follows: press the SEL key and the CODE LED will
start flashing, then press the SET key: the CODE LED will
switch off and the procedure is complete.
Warning that radio control is already stored or not
storable:
The control unit can store up to 215 radio controls with
different fixed or rolling codes. If the user attempts to perform
the programming procedure for a radio control which is already
stored in the memory or is not storable, the CODE LED will
begin to flash rapidly for a few moments to indicate that this
procedure cannot be performed; the unit then returns to the
programming stage once again.
2) CODE PED: (Pedestrian radio control code).
The programming and deleting procedure is the same as the
one illustrated above, but instead referring to the PEDONALE
CODE LED.
3) INB. CMD. AP: (command inhibition during opening and
pause time, if entered)
The command inhibition function during opening and pause
time, if entered, is used when automation includes the loop
detector. During opening or pause time the control unit ignores
the commands given by the loop detector at every passage.
The control unit is supplied with the default setting of the
command inhibition function during opening and pause time
not enabled. To enable the function proceed as follows: use
the SEL key to navigate to INB.CMD.AP when the relevant
LED is flashing, then press the SET key: the INB.CMD.AP LED
lights up and remains constant. Repeat the operation to
restore the previous configuration.
4) LAMP/CORT: (Flashing beacon or courtesy light selection)
The control unit has an output of 230 V a/c 500 W for
connection to a flashing beacon or courtesy light.
The control unit is supplied by the manufacturer with the
flashing beacon function enabled (even when the unit is
paused). To enable the flashing beacon function proceed as
follows: use the SEL button to navigate to LAMP/CORT. when
the corresponding LED is flashing, then press the SET button:
the LAMP/CORT. LED lights up and remains constant.
Repeat the operation to restore the default configuration.
To enable the courtesy light, repeat the operation above, by
pressing the SEL button twice (LAMP/CORT LED flashes
rapidly) instead of once. Repeat the operation to restore the
default configuration.
Flashing beacon function while the unit is paused:
The 230 V a/c output will activate every time automation takes
place, for the duration of the motor timer. If the Pause Time is
stored, the 230 V a/c output will also be active during the
Pause.

Flashing Beacon Operation:

The 230 V a/c output will
activate every time automation takes place, for the duration of
the motor timer.
Courtesy Light Operation: The 230 V a/c output will activate
for 3 minutes every time an opening command is given.
5) MOTOR TIME and DECELERATION: (Programming a motor
operation time of max. 4 minutes)

The control unit is supplied by the manufacturer with a default

motor operation time of 30 seconds, without deceleration.
To modify the motor operation time, proceed as follows when
the gate is closed: use the SEL key to navigate to T. MOT.
when the corresponding LED is flashing, then press the SET
key briefly and the Motor will begin its opening cycle; when the
initial point of deceleration is reached press the SET key again
and the motor will decelerate until the desired position is
reached. Press the SET key to complete the opening cycle.
The T. MOT. LED will start flashing rapidly; now repeat the
programming operation relating to the motor timer and
deceleration for the closing cycle. To deactivate the
deceleration function during programming, once the opening
and closing cycle is completed, press the SET key twice in
succession instead of just once.
During programming the radio control key on the control unit
can be used instead of the SET key, if stored previously.
6) T. PAUSA: (Programming the aut. closing time - 4 min. max.)
The control unit is supplied by the manufacturer without an
automatic closing procedure. To enable the automatic closing
function proceed as follows: use the SEL key to navigate to T.
PAUSA when the corresponding LED is flashing, then press
the SET key and wait for the required pause time, then press
the SET key again briefly; the automatic closing time is stored
and the T. PAUSA LED remains lit constantly.
To restore the initial configuration (without automatic closing)
navigate to T.PAUSA when the corresponding LED is flashing
then press the SET key twice within 2 seconds; the LED
switches off and the operation is complete.
During programming the radio control key on the control unit
can be used instead of the SET key, if stored previously.

EXTENDED MENU 1
The control unit is supplied by the manufacturer with only the
option of directly selecting the functions listed in the main
menu.
To enable the functions listed in extended menu 1, proceed as
follows: press the SET button and hold for 5 seconds; the T.
MOT. and T. PAUSA LEDs will flash alternately and the user
has 30 seconds within which to select the functions of
extended menu 1 using the SEL and SET buttons. When this
time has elapsed the control unit returns to the main menu.
---------------------- EXTENDED MENU 1 ----------------LED Reference
LED Off
LED On
A) CODE
Remote PGM = OFF
Remote PGM = ON
B) CODE PED.
Step-by-Step
Automatic Operation
C) INB.CMD.A
Pressure Maintenance = OFF
Press. Mainten. =
ON
D) LAMP/CORT
Electronic Brake= OFF
Electronic Brake =
ON
E) T. MOT.
Flashing beacon ON/OFF
F) T. PAUSA.
Flashing beacon ON/OFF

A) CODE
(Remote programming of radio control):
The control unit allows the transmission code to be
programmed by remote, without using the SEL key.
To programme the transmission code from remote proceed as
follows: send the radio control code continuously for more than
10 seconds and the control unit will enter the programming
mode as described above for the CODE LED in the main
menu.

The control unit is supplied by the manufacturer with remote

programming of the transmission code not enabled; to enable
the function proceed as follows: check that the extended menu
1 is enabled (the T. MOT. and T. PAUSA LEDs start flashing
alternatively), use the SEL key to navigate to the CODE when
the corresponding LED is flashing and press the SET key: the
CODE is enabled and programming is complete. Repeat the
operation to restore the previous configuration.
B) PED. CODE. (Step-by-Step / Automatic Operation):
The control unit is supplied by the manufacturer with the
Automatic operation function disabled. To enable the function
proceed as follows: check that the extended menu 1 is enabled
(the T. MOT. and T. PAUSA LEDs start flashing alternatively),
use the SEL key to navigate to PED. CODE when the
corresponding LED is flashing and press the SET key: the
PED. CODE LED lights up and programming is complete.
By using both the radio control and the low voltage pushbutton station to control the shutter, the following operation
may be obtained: the first press opens the shutter until the
programmed motor time elapses while the second press
closes it; if a button is pressed before the programmed motor
time has elapsed, the control unit inverts the motion, whether
during the opening or closing process. Repeat the operation to
restore the previous configuration.
C) INB. CMD. AP (Maintaining Hydraulic Motor Pressure):
The control unit is supplied by the manufacturer with the
hydraulic motor pressure maintenance disabled. To enable the
function proceed as follows: check that the extended menu 1 is
enabled (the T. MOT. and T. PAUSA LEDs start flashing
alternatively), use the SEL key to navigate to INB. CMD. AP.
when the corresponding LED is flashing and press the SET
key: the INB. CMD. AP. LED lights up and programming is
complete. In this way the control unit will send a closing
command to the motor every 2 hours for 2 seconds. Repeat
the operation to restore the previous configuration.
D) LAMP/CORT (Electronic Brake):
The control unit is supplied by the manufacturer with the
electronic brake function disabled. To enable the function
proceed as follows: check that the extended menu 1 is enabled
(the T. MOT. and T. PAUSA LEDs start flashing alternatively),
use the SEL key to navigate to LAMP/CORT. when the
corresponding LED is flashing and press the SET key: the
LAMP/CORT. switches on and programming is complete. The
control unit reduces the forward motion of the gate due to
inertia in the presence of a stop or inversion command. Repeat
the operation to restore the previous configuration.

EXTENDED MENU 2
The control unit is supplied by the manufacturer with only the
option of directly selecting the functions listed in the main
menu.
To enable the functions listed in extended menu 2, proceed as
follows: access extended menu 1 (as described in the relevant
paragraph), then press the SET button again and hold for 5
seconds; the T. MOT. and T. PAUSA LEDs will flash
simultaneously and the user has 30 seconds within which to
select the functions of extended menu 2 using the SEL and
SET buttons. When this time has elapsed the control unit
returns to the main menu.
EXTENDED MENU 2
LED status
A) CODE
3) PED. CODE
C) INB.CMD.AP
D) LAMP/CORT
E) T. MOT.

LED off
LED on
1 sec. inversion time
0.5 sec. inversion time
Soft Start = OFF
Soft Start = ON
User present CH = OFF
User present CH = ON
Input PUL = PUL
Input PUL = D.S.
Simultaneous flashing beacon ON/OFF

F) T. PAUSA.

Simultaneous flashing beacon ON/OFF

A) CODE (Inversion Time Selection 1 s / 0.5 s ):

The control unit is supplied by the manufacturer with the time
taken to invert the rotation movement of the motor set at about
1 second; to increase the inversion speed to about 0.5 second,
proceed as follows: check that extended menu 2 is enabled (T.
MOT. and T. PAUSA LEDs start flashing simultaneously), use
the SEL button to navigate to the CODE LED when flashing
and press the SET button: the CODE LED remains
permanently lit and programming is complete. Repeat the
operation to restore the previous configuration.
B) PED. CODE ( Soft Start ) :
The control unit is supplied by the manufacturer with the Soft
Start operation mode disabled. To enable the function proceed
as follows: check that extended menu 2 is enabled (T. MOT.
and T. PAUSA LEDs flash simultaneously), use the SEL
button to navigate to the CODE PED LED when flashing and
press the SET button: the CODE PED LED remains
permanently lit and programming is complete. This means that
at every start of movement, the control unit will govern the way
the motor starts, bringing the power in gradually, from
minimum to maximum in the first 2 seconds of operation.
Repeat the operation to restore the previous configuration.
C) INB. CMD. AP (User present during closure operation) :
The control unit is supplied by the manufacturer with the user
present during closure function disabled. To enable the
function proceed as follows: make sure that extended menu 2
is enabled (the T. MOT. and T. PAUSA LEDs flash
simultaneously), use the SEL button to navigate to INB. CMD.
AP. when the corresponding LED is flashing and press the
SET button: the INB. CMD. AP. switches on and programming
is complete. The control unit will now operate in User Present
mode during the closure phase. Repeat the operation to
restore the previous configuration.
D) LAMP/CORT (Selecting Input PUL = PUL / D.S. ):
The control unit is supplied by the manufacturer with Input PUL
= PUL, i.e. with the operation mode for the normal connection
of the command button (NO). If you wish to define Input PUL =
D.S., i.e. with the operating mode for the connection of a safety
device (NC) (intervention during the opening stage causes the
opening gate to stop immediately, followed directly by a brief
inversion of the direction of travel), proceed as follows: check
that extended menu 2 is enabled (T. MOT. and T. PAUSA
LEDs start flashing simultaneously), press the SEL button until
the LAMP/CORT LED flashes and press the SET button: the
LAMP/CORT LED remains permanently lit and programming is
complete.
Warning: connect any safety device only after
programming Input PUL = D.S. If necessary, it is possible
to restore the previous configuration, taking care to
disconnect the safety device first.
RESET:
To restore the default configuration, press the SEL and SET
keys simultaneously, all RED LEDs will light up and then
switch off.
DIAGNOSTICS:
Command input test:
The control unit is fitted with an LED for every low voltage
command input so that the status may be monitored
immediately.
Operation principle: LED on = input closed, LED off = input
open.

NOTES FOR THE INSTALLER

The control unit was designed for installation with other
components (motor, gate, safety devices) in order to form a
finished product (machine) in compliance with the Machines
Directive.
The safety of the final installation site and adherence to all
current legislation is the responsibility of the individual
assembling the various parts to construct a complete closure
device.
We advise that you also take note of the following
recommendations:

Before shutter automation, it is necessary to check the

product is in good condition and that it complies with EN
12604 and the Machines Directive.

The wiring of external electrical components must comply

with EN 60204-1 as amended in section 5.2.7 of EN
12453. Power supply leads and connection cables must
be secured through the use of cable clamps, which are
supplied with the product.

The motor reducer used to move the shutter must comply

with section 5.2.7. of EN 12453.

If present, the keypad for manual control must be mounted

in such a way that the user is not placed in a dangerous
situation, in compliance with point 5.2.8 of EN 12453.
The control unit is not equipped with a 230 V a/c electric
line sectioning device. The installer is responsible for
installing a sectioning device in the system. An omnipolar
switch with overheating category III must be installed.
The sectioning device must be positioned so that it is
protected against accidental closure, in compliance with
section 5.2.9 of standard EN 12453.

In compliance with section 5.4.2 of EN 12453 it is

recommended that motor reducers fitted with an

electromechanical unlocking device are used, so that the
shutter can be moved manually if necessary.

In

compliance

with

section

5.4.3

of

EN

12453,

electromechanical unlocking systems or similar devices

should be used as these enable the shutter to stop safely
at its stop limit.
Power supply and motor connection cables which are
suitable for use in conjunction with the pg9 cable clamps
provided must have an external diameter with a
measurement between 4.5 and 7 mm. The internal
conductor wires must have a nominal cross-section of
0.75 mm. If a channel is not used, we recommend that
cables in H05RR-F material are used.

Once installation is complete, all the checks listed in EN

12453 EN 12445 must be performed so as to ensure

that closure occurs in compliance with all stipulations.

For the radio receiver to operate correctly when two or

more control units are used, we recommend that you
install the devices at least 3 metres away from each
other.

FOR THE USER - IMPORTANT

- The device should not be used by children or by individuals

with reduced physical or psychological abilities unless
supervision is provided or instruction given on how to operate
it.
- Do not let children play with the device; keep radio controls
out of their reach.
- CAUTION: Keep this instruction manual in a safe place and
adhere to the important safety instructions contained within it.
Non-adherence to these instructions may lead to property
damage and serious accidents.
- Examine the system frequently to check for any signs of
damage. Do not use the device if it needs to be repaired.

Warning
All operations which require the casing to be opened (such as
wire connection, programming, etc.) must be carried out during
installation, by skilled staff only.
For any other procedure which requires the casing to be
opened again (programming, repairs or site modifications),
please contact the technical assistance service.

SEAV s.r.l. hereby declares that the below products:

Electronic Control Unit:

LG 2102R ++ - LRS 2102R ++
LRS 2102R ++ SET - LRH 2102R ++
comply with the requirements of Directives
R&TTE
99/5/EC, EMC 2004/108/EC, LVD 2006/95/EC.

Rev. 1.2 dated 01/04/09