FS-1100 FS-1300D: FS-2020D/FS-3920DN/FS-4020DN/ FS-6970DN

OPERATION GUIDE
FS-2020D/FS-3920DN/FS-4020DN/
FS-1100
FS-6970DN
FS-1300D
This Operation Guide is for models FS-2020D, FS-3920DN, FS-4020DN

and FS-6970DN.
Note This Operation Guide contains information that corresponds
to using both the inch and metric versions of these machines.
The inch versions of these machines are shown in the screens in
this guide. If you are using the metric version, use the messages
provided for the inch version as reference only. In the body text,
only the inch messages are given if these versions differ only in
capitalization. When there is even a slight difference in the
message, we have listed the information for the inch version
followed, in brackets, by the corresponding information for the
metric version.
Included Guides
The following guides are included with this machine. Refer to the proper
guide based on your requirements.
Operation Guide (This Guide)

Describes how to load paper, print, replace toner, clean the printer, and
troubleshooting.
Advanced Operation Guide

Explains paper guidelines, how to use the operation panel and possible
connections between the printer and the computer.
Installation Guide
Explains how to install this printer, as well as connecting cables and
loading paper.
Contents
1
Machine Parts ..................................................................... 1-1

Components at the Front of the Printer .......................... 1-2
Components at the Rear of the Printer ............................ 1-3
Operation Panel ................................................................. 1-4
Paper Handling ................................................................... 2-1

General Guidelines ............................................................ 2-2
Selecting the Right Paper ................................................. 2-4
Paper Type ....................................................................... 2-12
Loading Paper .................................................................... 3-1

Loading Paper into the Cassette ...................................... 3-2
Loading Paper into MP (Multi-Purpose) Tray .................. 3-6
Loading Envelopes into the MP Tray
(FS2020D/3920DN/4020DN only) ...................................... 3-8
Connecting and Printing .................................................... 4-1

Connections ....................................................................... 4-2
Changing Network Interface Parameters ........................ 4-4
Printing a Network Interface Status Page ..................... 4-12
Installing the Printer Driver ............................................ 4-13
Printing from Application Software ............................... 4-19
Status Monitor ................................................................. 4-20
Uninstalling Software (Windows PC) ............................. 4-24
Maintenance ........................................................................ 5-1

General Information .......................................................... 5-2
Cleaning the Printer .......................................................... 5-7
Troubleshooting ................................................................. 6-1

General Guidelines ............................................................ 6-2
Print Quality Problems ...................................................... 6-3
Error Messages ................................................................. 6-5
Clearing Paper Jams ....................................................... 6-12
Using the Operation Panel ................................................. 7-1

Understanding the Operation Panel ................................ 7-3
Using the Menu Selection System ................................... 7-8
Report Print ...................................................................... 7-11
USB Memory (USB flash memory selection) ................ 7-17
Job Box ............................................................................ 7-19
Counter (Viewing the counter value) ............................. 7-25
Paper Settings ................................................................. 7-26
Print Settings ................................................................... 7-35
Network (Network settings) ............................................ 7-50
Device Common (Selecting/Setting the common
device) .............................................................................. 7-55
Security ............................................................................ 7-67
Job Accounting (Job Accounting selection/setting) ... 7-75
Admin (Administrator settings) ...................................... 7-81
Adjust/Maintenance (Adjust/Maintenance selection/
setting) ............................................................................. 7-83
Options ................................................................................ 8-1

Expansion Memory Modules ............................................ 8-4
Paper Feeder (PF-310) ....................................................... 8-6

Paper Feeder (PF-430) ....................................................... 8-6
CompactFlash (CF) Card ................................................... 8-7
Other Options .................................................................... 8-9
9
Computer Interface ............................................................. 9-1

General Information ........................................................... 9-2
Network Interface .............................................................. 9-3
10 Appendix ........................................................................... 10-1

Specifications .................................................................. 10-2
Glossary
Index
ii
Legal and Safety

Information
Please read this information before using your machine. This chapter
provides information on the following topics:
Legal Information
License Agreements
Safety Information
Symbols
Installation Precautions
Precautions for Use
About the Operation Guide
Conventions in This Guide
iv
v
xii
xvii
xviii
xx
xxii
xxiii
iii
Legal Information
CAUTION NO LIABILITY IS ASSUMED FOR ANY
DAMAGE CAUSED BY IMPROPER INSTALLATION.
Notice on Software
SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE
PRINTER'S EMULATION MODE. The printer is factory-set to emulate
the PCL. The emulation mode can be changed.
Notice
The information in this guide is subject to change without notification.
Additional pages may be inserted in future editions.
The user is asked to excuse any technical inaccuracies or typographical
errors in the present edition.No responsibility is assumed if accidents
occur while the user is following the instructions in this guide. No
responsibility is assumed for defects in the printer's firmware (contents of
its read-only memory).
This guide, and any copyrightable subject matter sold or provided with or
in connection with the sale of the page printer, are protected by
copyright. All rights are reserved. Copying or other reproduction of all or
part of this guide, or any copyrightable subject matter without the prior
written consent of Kyocera Mita Corporation is prohibited. Any copies
made of all or part of this guide, or any copyrightable subject must
contain the same copyright notice as the material from which the copying
is done.
Regarding Tradenames
PRESCRIBE is a registered trademark of Kyocera Corporation. KPDL is
trademark of Kyocera Corporation.Hewlett-Packard, PCL, and PJL are
registered trademarks of Hewlett-Packard Company. Centronics is a
trade name of Centronics Data Computer Inc. Adobe, Acrobat, Flash,
and PostScript are registered trademarks of Adobe Systems
Incorporated. Macintosh is a registered trademark of Apple Computer,
Inc. Microsoft, Windows, and Windows NT are registered trademarks of
Microsoft Corporation. Microsoft Windows Server is a trademark of
Microsoft Corporation. PowerPC is a trademark of International Business
Machines Corporation. CompactFlash is a trademark of SanDisk
Corporation. ENERGY STAR is a U.S. registered mark. All other brand
and product names are registered trademarks or trademarks of their
respective companies.
This product was developed using the Tornado Real Time Operating
System and Tools from Wind River Systems.
This product contains UFST and MicroType from Monotype Imaging
Inc.
iv
License Agreements
IBM Program License Agreement
THE DEVICE YOU HAVE PURCHASED CONTAINS ONE OR MORE
SOFTWARE PROGRAMS (PROGRAMS) WHICH BELONG TO
INTERNATIONAL BUSINESS MACHINES CORPORATION (IBM).
THIS DOCUMENT DEFINES THE TERMS AND CONDITIONS UNDER
WHICH THE SOFTWARE IS BEING LICENSED TO YOU BY IBM. IF
YOU DO NOT AGREE WITH THE TERMS AND CONDITIONS OF THIS
LICENSE, THEN WITHIN 14 DAYS AFTER YOUR ACQUISITION OF
THE DEVICE YOU MAY RETURN THE DEVICE FOR A FULL
REFUND. IF YOU DO NOT SO RETURN THE DEVICE WITHIN THE 14
DAYS, THEN YOU WILL BE ASSUMED TO HAVE AGREED TO THESE
TERMS AND CONDITIONS.
The Programs are licensed not sold. IBM, or the applicable IBM country
organization, grants you a license for the Programs only in the country
where you acquired the Programs. You obtain no rights other than those
granted you under this license.
The term Programs means the original and all whole or partial copies of
it, including modified copies or portions merged into other programs. IBM
retains title to the Programs. IBM owns, or has licensed from the owner,
copyrights in the Programs.
1. License
Under this license, you may use the Programs only with the device on
which they are installed and transfer possession of the Programs and
the device to another party.
If you transfer the Programs, you must transfer a copy of this license and
any other documentation to the other party. Your license is then
terminated. The other party agrees to these terms and conditions by its
first use of the Program.
You may not:
1. use, copy, modify, merge, or transfer copies of the Program except as
provided in this license;
2. reverse assemble or reverse compile the Program; or
3. sublicense, rent, lease, or assign the Program.
2. Limited Warranty
The Programs are provided AS IS.
THERE ARE NO OTHER WARRANTIES COVERING THE
PROGRAMS (OR CONDITIONS), EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some jurisdictions do not allow the exclusion of implied warranties, so
the above exclusion may not apply to you.
3. Limitation of Remedies
IBM's entire liability under this license is the following;
For any claim (including fundamental breach), in any form, related in any
way to this license, IBM's liability will be for actual damages only and will
be limited to the greater of:
1. the equivalent of U.S. $25,000 in your local currency; or

2. IBM's then generally available license fee for the Program
This limitation will not apply to claims for bodily injury or damages to real
or tangible personal property for which IBM is legally liable.
IBM will not be liable for any lost profits, lost savings, or any incidental
damages or other economic consequential damages, even if IBM, or its
authorized supplier, has been advised of the possibility of such
damages. IBM will not be liable for any damages claimed by you based
on any third party claim. This limitation of remedies also applies to any
developer of Programs supplied to IBM. IBM's and the developer's
limitations of remedies are not cumulative. Such developer is an
intended beneficiary of this Section. Some jurisdictions do not allow
these limitations or exclusions, so they may not apply to you.
4. General
You may terminate your license at any time. IBM may terminate your
license if you fail to comply with the terms and conditions of this license.
In either event, you must destroy all your copies of the Program. You are
responsible for payment of any taxes, including personal property taxes,
resulting from this license. Neither party may bring an action, regardless
of form, more than two years after the cause of action arose. If you
acquired the Program in the United States, this license is governed by
the laws of the State of New York. If you acquired the Program in
Canada, this license is governed by the laws of the Province of Ontario.
Otherwise, this license is governed by the laws of the country in which
you acquired the Program.
Typeface Trademark Acknowledgement

All resident fonts in this printer are licensed from Monotype Imaging Inc.
Helvetica, Palatino and Times are registered trademarks of Linotype-Hell
AG. ITC Avant Garde Gothic, ITC Bookman, ITC ZapfChancery and ITC
Zapf Dingbats are registered trademarks of International Typeface
Corporation.
Monotype Imaging License Agreement

1. Software shall mean the digitally encoded, machine readable,
scalable outline data as encoded in a special format as well as the
UFST Software.
2. You agree to accept a non-exclusive license to use the Software to
reproduce and display weights, styles and versions of letters,
numerals, characters and symbols (Typefaces) solely for your own
customary business or personal purposes at the address stated on
the registration card you return to Monotype Imaging. Under the
terms of this License Agreement, you have the right to use the Fonts
on up to three printers. If you need to have access to the fonts on
more than three printers, you need to acquire a multi-user license
agreement which can be obtained from Monotype Imaging.
Monotype Imaging retains all rights, title and interest to the Software
and Typefaces and no rights are granted to you other than a License
to use the Software on the terms expressly set forth in this
Agreement.
vi
3. To protect proprietary rights of Monotype Imaging, you agree to

maintain the Software and other proprietary information concerning
the Typefaces in strict confidence and to establish reasonable
procedures regulating access to and use of the Software and
Typefaces.
4. You agree not to duplicate or copy the Software or Typefaces, except
that you may make one backup copy. You agree that any such copy
shall contain the same proprietary notices as those appearing on the
original.
5. This License shall continue until the last use of the Software and
Typefaces, unless sooner terminated. This License may be
terminated by Monotype Imaging if you fail to comply with the terms
of this License and such failure is not remedied within thirty (30) days
after notice from Monotype Imaging. When this License expires or is
terminated, you shall either return to Monotype Imaging or destroy all
copies of the Software and Typefaces and documentation as
requested.
6. You agree that you will not modify, alter, disassemble, decrypt,
reverse engineer or decompile the Software.
7. Monotype Imaging warrants that for ninety (90) days after delivery,
the Software will perform in accordance with Monotype Imagingpublished specifications, and the diskette will be free from defects in
material and workmanship. Monotype Imaging does not warrant that
the Software is free from all bugs, errors and omissions.
8. THE PARTIES AGREE THAT ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF
FITNESS
FOR
A
PARTICULAR
PURPOSE
AND
MERCHANTABILITY, ARE EXCLUDED.
9. Your exclusive remedy and the sole liability of Monotype Imaging in
connection with the Software and Typefaces is repair or replacement
of defective parts, upon their return to Monotype Imaging.
10. IN NO EVENT WILL MONOTYPE IMAGING BE LIABLE FOR LOST
PROFITS, LOST DATA, OR ANY OTHER INCIDENTAL OR
CONSEQUENTIAL DAMAGES, OR ANY DAMAGES CAUSED BY
ABUSE OR MISAPPLICATION OF THE SOFTWARE AND
TYPEFACES.
11. Massachusetts U.S.A. law governs this Agreement.
12. You shall not sublicense, sell, lease, or otherwise transfer the
Software and/or Typefaces without the prior written consent of
Monotype Imaging.
13. Use, duplication or disclosure by the Government is subject to
restrictions as set forth in the Rights in Technical Data and Computer
Software clause at FAR 252-227-7013, subdivision (b)(3)(ii) or
subparagraph (c)(1)(ii), as appropriate. Further use, duplication or
disclosure is subject to restrictions applicable to restricted rights
software as set forth in FAR 52.227-19 (c)(2).
14. YOU ACKNOWLEDGE THAT YOU HAVE READ THIS
AGREEMENT, UNDERSTAND IT, AND AGREE TO BE BOUND BY
ITS TERMS AND CONDITIONS. NEITHER PARTY SHALL BE
BOUND BY ANY STATEMENT OR REPRESENTATION NOT
CONTAINED IN THIS AGREEMENT. NO CHANGE IN THIS
AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED BY
PROPERLY AUTHORIZED REPRESENTATIVES OF EACH PARTY.
BY OPENING THIS DISKETTE PACKAGE, YOU AGREE TO
ACCEPT THE TERMS AND CONDITIONS OF THIS AGREEMENT.
vii
GPL
Firmware of this machine is using in part the GPL applied codes
(www.fsf.org/copyleft/gpl.html). Please access "http://
www.kyoceramita.com/gpl" for more information on how to make GPL
applied codes available.
Open SSLeay License

Copyright 1998-2006 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
1
Redistributions of source code must retain the above copyright

notice, this list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
All advertising materials mentioning features or use of this software

must display the following acknowledgment:
"This product includes software developed by the OpenSSL Project
for use in the OpenSSL Toolkit. (http://www.openssl.org/)"
The names "OpenSSL Toolkit" and "OpenSSL Project" must not be

used to endorse or promote products derived from this software
without prior written permission.
For written permission, please contact [email protected].
Products derived from this software may not be called "OpenSSL"

nor may "OpenSSL" appear in their names without prior written
permission of the OpenSSL Project.
Redistributions of any form whatsoever must retain the following

acknowledgment: "This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit (http://
www.openssl.org/)"
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS"

AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR
ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
viii
Original SSLeay License

Copyright 1995-1998 Eric Young ([email protected]) All rights
reserved.
This package is an SSL implementation written by Eric Young
([email protected]). The implementation was written so as to conform
with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the
following conditions are aheared to. The following conditions apply to all
code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code;
not just the SSL code. The SSL documentation included with this
distribution is covered by the same copyright terms except that the holder
is Tim Hudson ([email protected]).
Copyright remains Eric Young's, and as such any Copyright notices in the
code are not to be removed.
If this package is used in a product, Eric Young should be given attribution
as the author of the parts of the library used.
This can be in the form of a textual message at program startup or in
documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
1
Redistributions of source code must retain the copyright notice, this

list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
All advertising materials mentioning features or use of this software

must display the following acknowledgement:
"This product includes cryptographic software written by Eric Young
([email protected])"
The word 'cryptographic' can be left out if the rouines from the library
being used are not cryptographic related :-).
If you include any Windows specific code (or a derivative thereof)

from the apps directory (application code) you must include an
acknowledgement:
"This product includes software written by Tim Hudson
([email protected])"
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
ix
The licence and distribution terms for any publically available version or
derivative of this code cannot be changed, i.e, the code cannot simply be
copied and put under another distribution licence [including the GNU
Publica License.]
Compliance and Conformity

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The use of a non-shielded interface cable with the referenced device
is prohibited.
CAUTION The changes or modifications not expressly approved by

the party responsible for compliance could void the userfs authority to
operate the equipment.
This device complies with Part 15 of FCC Rules and RSS-Gen of IC
Rules.
Operation is subject to the following two conditions; (1) this device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
* The above warning is valid only in the United States of America.
Interface Connectors
IMPORTANT Be sure to power off the printer before connecting or

disconnecting an interface cable. For protection against static
electricity discharge to the printer's internal electronics through the
interface connector(s), cover any interface connector that is not in use
with the protective cap supplied.
Note Use shielded interface cables.
xi
Safety Information
Laser Safety
This printer is certified as a Class 1 laser product under the U.S.
Department of Health and Human Services (DHHS) Radiation
Performance Standard according to Radiation Control for Health and
Safety Act of 1968. This means that the printer does not produce
hazardous laser radiation. Since radiation emitted inside the printer is
completely confined within protective housings and external covers, the
laser beam cannot escape from the printer during any phase of user
operation.
Laser Notice
This printer is certified in the U.S. to conform to the requirements of
DHHS 21 CFR Subchapter for Class I (1) laser products, and elsewhere
is certified as a Class I laser product conforming to the requirements of
IEC 825.
DANGER CLASS 3B LASER RADIATION WHEN OPEN.

AVOID DIRECT EXPOSURE TO BEAM.
CAUTION Use of controls or adjustments or performance
of procedures other than those specified herein may result
in hazardous radiation exposure.
Radio Frequency Transmitter

This machine contains a transmitter module. We, the manufacturer
(Kyocera Mita Corporation) hereby declare that this equipment (page
printer), models mentioned on the cover page are in compliance with the
essential requirements and other relevant provisions of Directive
1999/5/EC.
Radio Tag Technology

In some countries, the radio tag technology used in this equipment to
identify the toner container may be subject to authorization, and the use
of this equipment may consequently be restricted.
xii
Caution Labels
The printer bears any of the following labels.
Laser inside the printer
(Laser radiation warning)
For Europe, Asia, and

other countries
For U.S.A. and

Canada
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S.
Food and Drug Administration implemented regulations for laser
products on August 2, 1976. These regulations apply to laser products
manufactured after August 1, 1976. Compliance is mandatory for
products marketed in the United States. A label indicating compliance
with the CDRH regulations must be attached to laser products marketed
in the United States.
Ozone Concentration
These printers generate ozone gas (O3), which may concentrate in the
place of installation and cause an unpleasant smell. To minimize the
concentration of ozone gas to less than 0.1ppm, we recommend you not
to install the printer in a confined area where ventilation is blocked.
xiii
Safety Instructions Regarding the

Disconnection of Power
Caution: The power plug is the main isolation device! Other switches on
the equipment are only functional switches and are not suitable for
isolating the equipment from the power source.
VORSICHT: Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen
Schalter auf dem Gert sind nur Funktionsschalter und knnen nicht
verwendet werden, um den Stromflu im Gert zu unterbrechen.
DECLARATION OF CONFORMITY
TO
2004/108/EC, 2006/95/EEC, 93/68/EEC and 1999/5/EC
We declare under our sole responsibility that the product to which this
declaration relates is in conformity with the following specifications.
EN55024
EN55022 Class B
EN61000-3-2
EN61000-3-3
EN60950-1
EN60825-1
EN300 330-1
EN300 330-2
Declaration of Conformity (Australia)

Manufacturer: Kyocera Mita Corporation (Head Office)
Manufacturers address: 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka
540-8585, Japan
declares that the product
Product name: Page Printer
Model name: FS-2020D/FS-3920DN/FS-4020DN
Description of devices: This Page Printer Model FS-4020DN is 28ppm
(FS-2020D is the 30ppm, FS-3920DN is the 35ppm); A4 size and utilizes
plain paper; dry toner; etc. The printer can be equipped with several
optional enhancement units, such as a PF-310 paper feeder.
conforms to the following product specifications:
AS/NZS 3548: 1995 (EN 55 022: 1998 Class B)
AS/NZS 4268: 2003
IEC60950-1:2001 (EN 60 950-1: 2001+A11)
The manufacturer and its merchandising companies retain the following
technical documentation in anticipation of the inspection that may be
conducted by the authorities concerned:
Users instruction that conforms to the applicable specifications
Technical drawings
Descriptions of procedures that guarantee conformity
Other technical information
The manufacturer has been employed with ISO9001 scheme. JQA and
BS have attested the manufacturer.
xiv
Kyocera Mita Australia Pty., Ltd.

6-10 Talavera Road, North Ryde, NSW 2113, Australia
Telephone: +61 2-9888-9999
Fax: +61 2-9888-9588
Canadian Department of Communications

Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformit aux normes du ministere

des Communications du Canada
Cet appareil numrique de la classe B est conforme la norme NMB003 du Canada.
EN ISO 7779
Maschinenlrminformations-Verordnung 3. GPSGV, 06.01.2004: Der
hchste Schalldruckpegel betrgt 70 dB (A) oder weniger gem EN
ISO 7779.
Disclaimer
Kyocera Mita will not be liable to customers or any other person or entity
for any loss or damage caused or alleged to be caused directly or
indirectly by equipment sold or furnished by us, including but not limited
to, any interruption of service, loss of business or anticipatory profits, or
consequential damages resulting from the use or operation of the
equipment or software.
Energy Saving Function

This printer comes equipped with a Sleep Mode where printer function
remains in a waiting state but power consumption is still reduced to a
minimum when there is no activity with the printer within a set amount of
time.
Sleep Mode
This printer automatically enters Sleep Mode when approximately 30
minutes (FS-2020D/3920DN/4020DN)/5 minutes (FS-6970DN) have
passed since the printer was last used. The amount of time of no activity
that must pass before Sleep Mode is activated may be lengthened.
Duplex Printing
This printer includes duplex printing as a standard function. For example,
by printing two single-sided originals onto a single sheet of paper as a
duplex printing, it is possible to lower the amount of paper used.
Recycled Paper
This printer supports recycled paper which reduces the load on the
environment. Your sales or service representative can provide
information about recommended paper types.
xv
Energy Star (ENERGY STAR) Program

We have determined as a participating company in the International
Energy Star Program that this product is compliant with the standards
laid out in the International Energy Star Program.
xvi
Symbols
The sections of this guide and parts of the machine marked with symbols
are safety warnings meant to protect the user, other individuals and
surrounding objects, and ensure correct and safe usage of the machine.
The symbols and their meanings are indicated below.
DANGER: Indicates that serious injury or even death will very
possibly result from insufficient attention to or incorrect
compliance with the related points.
WARNING: Indicates that serious injury or even death may
result from insufficient attention to or incorrect compliance with
the related points.
CAUTION: Indicates that personal injury or mechanical
damage may result from insufficient attention to or incorrect
compliance with the related points.
The following symbols indicate that the related section includes safety
warnings. Specific points of attention are indicated inside the symbol.
.... [General warning]
.... [Warning of danger of electrical shock]
.... [Warning of high temperature]
The following symbols indicate that the related section includes
information on prohibited actions. Specifics of the prohibited action are
indicated inside the symbol.
.... [Warning of prohibited action]
.... [Disassembly prohibited]
The following symbols indicate that the related section includes
information on actions which must be performed. Specifics of the
required action are indicated inside the symbol.
.... [Alert of required action]
.... [Remove the power plug from the outlet]
....
[Always connect the machine to an outlet with a ground

connection]
Please contact your service representative to order a replacement if the

safety warnings in this Operation Guide are illegible or if the guide itself
is missing. (fee required)
xvii
Installation Precautions
Environment
Caution
Avoid placing the machine on or in locations which are unstable

or not level. Such locations may cause the machine to fall down
or fall over. This type of situation presents a danger of personal
injury or damage to the machine.
Avoid locations with humidity or dust and dirt. If dust or dirt
become attached to the power plug, clean the plug to avoid the
danger of fire or electrical shock.
Avoid locations near radiators, heaters, or other heat sources, or
locations near flammable items, to avoid the danger of fire.
To keep the machine cool and facilitate changing of parts and
maintenance, allow access space as shown below. Leave
adequate space, especially around the rear cover, to allow air to
be properly ventilated out of the printer.
11-13/16"
(300mm)
11-13/16"
(300mm)
3-15/16"
(100mm)
7-7/8"
(200mm) *
23-5/8"
(600mm)
* 15-3/4" (400mm) FS-3920DN/FS-4020DN: PT-310

FS-6970DN: PT-430.
Other Precautions
Adverse environmental conditions may affect the safe operation and
performance of the machine. Install in an air-conditioned room
(recommended room temperature: around 23C (73.4F), humidity:
around 60% RH), and avoid the following locations when selecting a site
for the machine.
Avoid locations near a window or with exposure to direct sunlight.

Avoid locations with vibrations.
Avoid locations with drastic temperature fluctuations.
Avoid locations with direct exposure to hot or cold air.
Avoid poorly ventilated locations.
During printing, some ozone is released, but the amount does not cause
any ill effect to one's health. If, however, the printer is used over a long
period of time in a poorly ventilated room or when printing an extremely
large number of copies, the smell may become unpleasant. To maintain
the appropriate environment for print work, it is suggested that the room
be properly ventilated.
xviii
Power Supply/Grounding the Machine
Warning
Do not use a power supply with a voltage other than that
specified. Avoid multiple connections in the same outlet. These
types of situations present a danger of fire or electrical shock.
Plug the power cord securely into the outlet. If metallic objects
come in contact with the prongs on the plug, it may cause a fire or
electric shock.
Always connect the machine to an outlet with a ground
connection to avoid the danger of fire or electrical shock in case
of an electric short. If an earth connection is not possible, contact
your service representative.
Other precautions
Connect the power plug to the closest outlet possible to the machine.
The power supply cord is used as the main disconnect device. Ensure
that the socket/outlet is located/installed near the equipment and is
easily accessible.
Handling of plastic bags
Warning
Keep the plastic bags that are used with the machine away from
children. The plastic may cling to their nose and mouth causing
suffocation.
Introduction-xix
Precautions for Use

Cautions when using the machine
Warning
Do not place metallic objects or containers with water (flower
vases, flower pots, cups, etc.) on or near the machine. This
situation presents a danger of fire or electrical shock should they
fall inside.
Do not remove any of the covers from the machine as there is a
danger of electrical shock from high voltage parts inside the
machine.
Do not damage, break or attempt to repair the power cord. Do not
place heavy objects on the cord, pull it, bend it unnecessarily or
cause any other type of damage. These types of situations
present a danger of fire or electrical shock.
Never attempt to repair or disassemble the machine or its parts as
there is a danger of fire, electrical shock or damage to the laser. If
the laser beam escapes, there is a danger of it causing blindness.
If the machine becomes excessively hot, smoke appears from the
machine, there is an odd smell, or any other abnormal situation
occurs, there is a danger of fire or electrical shock. Turn the main
power switch off ({) immediately, be absolutely certain to remove the
power plug from the outlet and then contact your service representative.
If anything harmful (paper clips, water, other fluids, etc.) falls into
the machine, turn the main power switch off ({) immediately.
Next, be absolutely certain to remove the power plug from the
outlet to avoid the danger of fire or electrical shock. Then contact your
service representative.
Do not remove or connect the power plug with wet hands, as
there is a danger of electrical shock.
Always contact your service representative for maintenance or
repair of internal parts.
Caution
Do not pull the power cord when removing it from the outlet. If the
power cord is pulled, the wires may become broken and there is a
danger of fire or electrical shock. (Always grasp the power plug
when removing the power cord from the outlet.)
Always remove the power plug from the outlet when moving the
machine. If the power cord is damaged, there is a danger of fire or
electrical shock.
If the machine will not be used for a short period of time
(overnight, etc.), turn the power switch off (O). If it will not be used
for an extended period of time (vacations, etc.), remove the power
plug from the outlet for safety purposes during the time the machine is
not in use.
Always hold the designated parts only when lifting or moving the
machine.
For safety purposes, always remove the power plug from the
outlet when performing cleaning operations.
Introduction-xx
If dust accumulates within the machine, there is a danger of fire or

other trouble. It is therefore recommended that you consult with
your service representative in regard to cleaning of internal parts.
This is particularly effective if accomplished prior to seasons of
high humidity. Consult with your service representative in regard
to the cost of cleaning the internal parts of the machine.
Other precautions
Do not place heavy objects on the machine or cause other damage to
the machine.
Do not open the upper front cover, turn off the main power switch, or pull
out the power plug during printing.
When lifting or moving the machine, contact your service representative.
Do not touch electrical parts, such as connectors or printed circuit
boards. They could be damaged by static electricity.
Do not attempt to perform any operations not explained in this
handbook.
Use shielded interface cables.
Caution
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
Cautions when Handling Consumables
Caution
Do not attempt to incinerate the Toner Container. Dangerous
sparks may cause burns.
Keep the Toner Container out of the reach of children.
If toner happens to spill from the Toner Container, avoid inhalation
and ingestion, as well as contact with your eyes and skin.
If you do happen to inhale toner, move to a place with fresh

air and gargle thoroughly with a large amount of water. If coughing
develops, contact a physician.
If you do happen to ingest toner, rinse your mouth out with water and
drink 1 or 2 cups of water to dilute the contents of your stomach. If
necessary, contact a physician.
If you do happen to get toner in your eyes, flush them thoroughly
with water. If there is any remaining tenderness, contact a physician.
If toner does happen to get on your skin, wash with soap and water.
Do not attempt to force open or destroy the Toner Container.
Other precautions
After use, always dispose of the Toner Container in accordance with
Federal, State and Local rules and regulations.
Store all consumables in a cool, dark location.
If the machine will not be used for an extended period of time, remove
the paper from the cassette, return it to its original package and reseal it.
Introduction-xxi
About the Operation Guide

This Operation Guide contains the following chapters:
Machine Parts
This chapter explains the names of parts.

2 Paper Handling
Explains how choose, handle and load paper.
3
Loading Paper
This chapter explains paper specifications for this printer and how to
load paper into the cassette or MP tray.
4
Connecting and Printing
This chapter explains how to start up the printer, print from your PC, and
use the application software included in the CD-ROM.
5
Maintenance
This chapter explains how to replace the toner container and how to care
for your printer.
6
Using the Operation Panel
Explains how to use the operation panel to configure the printer.

7
Options
Shows the available options.

8
Computer Interface
Describes the possible connections between the printer and your

computer.
9
Troubleshooting
This chapter explains how to handle printer problems that may occur,
such as paper jams.
10
Appendix
This chapter lists the specifications of this printer and explains

environmental standard requirements.
Glossary
A Glossary of terms used is provided here.
Introduction-xxii
Conventions in This Guide

This manual uses the following conventions.
Convention
Description
Italic
Typeface
Used to emphasize a key word,

phrase or reference to additional
information.
Bold
Used to denote buttons on the
software.
Bracket Bold Used to denote operation panel
keys.
Note
Used to provide additional or
useful information about a
function or feature.
Example
Refer to Replacing the Toner Container
on page 4-3.
Select the printer you want to install, and
click Next.
If TCP/IP is set to Off, use U or V to
select On and press [OK].
Note Do not remove the toner
container from the carton until you
are ready to install it in the printer.
Important
Used to provide important

information.
Caution
Cautions are statements that

CAUTION When pulling the paper, pull
suggest mechanical damage as it gently so as not to tear it. Torn pieces
a result of an action.
of paper are difficult to remove and may
IMPORTANT During toner container

replacement, temporarily move storage
media and computer supplies (such as
floppy disks) away from the toner
container. This is to avoid damaging
media by the magnetism of toner.
be easily overlooked, deterring the

paper jam recovery.
Warning
Used to alert users to the

possibility of personal injury.
WARNING If you ship the printer,

remove and pack the developer unit in
a plastic bag and ship them separately
from the printer.
Note The illustrations shown in the user manual are just

examples. Depending on the content either
2020D/3920DN/4020DN or FS-6970DN drawings are used.
Introduction-xxiii
Introduction-xxiv
Machine Parts
This section provides explanations and illustrations for you to

determine the parts and their functions. Try to be familiar with the
names and functions of these parts for correct use and optimal
performance.
Components at the Front of the Printer
Components at the Rear of the Printer
Operation Panel
Machine Parts
1-2
1-3
1-4
1-1
Components at the Front of the Printer

3
7
1
2
3
4
5
6
7
8
8
6
Top Cover
Paper Stopper
Top Tray
Right Cover
Operation Panel
USB Memory Slot
Paper Cassette
MP (Multi-Purpose) Tray
Components at the Left of the Printer and

Internal Components
4
1
2
3
4
1-2
Left Cover
Toner Container
Power Switch
Waste Toner Box
Machine Parts
Components at the Rear of the Printer
1
2
3
4
7
1
2
3
4
5
6
7
Machine Parts
USB Interface Connector

Network Indicators (FS-3920DN/FS-4020DN/FS-6970DN only)
Network Interface Connector (FS-3920DN/FS-4020DN/FS-6970DN
only)
Parallel Interface Connector
Power Cord Connector
Rear Unit
Option Interface Slot (Network/CF card/Hard disk) (FS-2020D/
FS-3920DN/FS-4020DN only)
1-3
Operation Panel
1
2
7
3
6
1
2
3
4
5
6
7
1-4
Indicators
Message Display
Cursor Keys
[GO] Key
[Cancel] Key
[OK] Key
[MENU] Key
Machine Parts
Paper Handling
This chapter explains paper specifications for this printer and how to
load paper into the cassette or MP tray.
General Guidelines
Selecting the Right Paper
Paper Type
Paper Handling
2-2
2-4
2-12
2-1
General Guidelines
The machine is designed to print on standard copier paper, but it can
also accept a variety of other types of paper within the limits specified
below.
Note The manufacturer assumes no liability for problems that
occur when paper not satisfying these requirements is used.
Selection of the right paper is important. Using the wrong paper can
result in paper jams, curling, poor print quality, and paper waste, and in
extreme cases can damage the machine. The guidelines given below
will increase the productivity of your office by ensuring efficient, troublefree printing and reducing wear and tear on the machine.
Paper Availability
Most types of paper are compatible with a variety of machines. Paper
intended for xerographic copiers can also be used with the machine.
There are three general grades of paper: economy, standard, and
premium. The most significant difference between grades is the ease
with which they pass through the machine. This is affected by the
smoothness, size, and moisture content of the paper, and the way in
which the paper is cut. The higher the grade of paper you use, the less
risk there will be of paper jams and other problems, and the higher the
level of quality your printed output will reflect.
Differences between paper from different suppliers can also affect the
machine's performance. A high-quality printer cannot produce highquality results when the wrong paper is used. Low-priced paper is not
economical in the long run if it causes printing problems.
Paper in each grade is available in a range of basis weights (defined
later). The traditional standard weights are 60 to 120 g/m2 (16 to 31.9b).
Paper Specifications
The following table summarizes the basic paper specifications. Details
are given on the following pages:
Item
Specifications
Weight
Cassette: 60 to 120 g/m (16 to 31.9 lb/ream)

MP tray: 60 to 220 g/m (16 to 58.5 lb/ream)
0.086 to 0.110mm (3.4 to 4.3 mils)
0.7 mm (0.0276 inches)
Thickness
Dimensional
Accuracy
Squareness of
Corners
Moisture Content
Direction of Grain
Pulp Content
2-2
900.2
4 to 6%
Long grain
80% or more
Paper Handling
Minimum and Maximum Paper Sizes

The minimum and maximum paper sizes are as follows. For non
standard paper, the MP tray must be used.
For FS-2020D/3920DN/4020DN:
105mm (4-1/8 inches)
356mm (14 inches)
148mm (5-13/16 inches)
356mm (14 inches)
Minimum
Paper Size
148mm (5-13/16 inches)
MP tray
Paper cassette
Minimum
Paper Size
70mm (2-3/4 inches)
Maximum
Paper Size
Maximum
Paper Size
Note The minimum paper sizes of the paper cassette for

FS-2020D is 140mm (5-1/2 inches) x 210mm (8-1/4 inches).
For FS-6970DN:
148mm (5-13/16 inches)
Maximum
Paper Size
297mm (11-3/4 inches)
Paper Handling
450mm (17-3/4 inches)
432mm (17 inches)
Minimum
Paper Size
148mm (5-13/16 inches)
MP tray
Paper cassette
Minimum
Paper Size
70mm (2-3/4 inches)
Maximum
Paper Size
297mm (11-3/4 inches)
2-3
Selecting the Right Paper

This section describes the guidelines for selecting paper.
Condition
Avoid using paper that is bent at the edges, curled, dirty, torn,
embossed, or contaminated with lint, clay, or paper shreds.
Use of paper in these conditions can lead to illegible printing and paper
jams, and can shorten the life of the machine. In particular, avoid using
paper with a surface coating or other surface treatment. Paper should
have as smooth and even a surface as possible.
Composition
Do not use paper that has been coated or surface-treated and contains
plastic or carbon. The heat of fusing can cause such paper to give off
harmful fumes.
Bond paper should contain at least 80% pulp. Not more than 20% of the
total paper content should consist of cotton or other fibers.
Paper Sizes
Cassettes and the MP Tray are available for the paper sizes shown
below. The dimensional tolerances are 0.7mm for the length and width.
The angle at the corners must be 90 0.2.
For FS-2020D/3920DN/4020DN:
MP Tray
Size
Cassette or
MP Tray
Envelope Monarch
Envelope #10
Envelope DL
Envelope #9
Envelope #6
3-7/8 x 7-1/2 inches

4-1/8 x 9-1/2 inches
110 x 220 mm
3-7/8 x 8-7/8 inches
3-5/8 x 6-1/2 inches
Legal
Letter
ISO A4
ISO A5
ISO A6
JIS B6
Hagaki
Ofuku-Hagaki
Youkei 2
Youkei 4
Custom
2-4
Size
8-1/2 x 14 inches
8-1/2 x 11 inches
148 x 297 mm
148 x 210 mm
105 x 148 mm
(FS-2020D: MP Tray
only)
128 x 182 mm
Envelope C5
162 x 229 mm
100 x 148 mm
ISO B5
176 x 250 mm
148 x 200 mm
JIS B5
182 x 257 mm
114 x 162 mm
Executive
7-1/4 x 10-1/2 inches
105 x 235 mm
Oficio II
8-1/2 x 13 inches
Folio
210 x 330 mm
Statement
5-1/2 x 8-1/2 inches
16 kai
197 x 273 mm
Cassette: 140 x 210 mm to 216 x 356 mm (FS-2020D); 105 x 148 mm
to 216 x 356 mm (FS-3920DN and FS-4020DN)MP Tray: 70 x 148
mm to 216 x 356 mm
Paper Handling
For FS-6970DN:
MP Tray
Size
Envelope Monarch
Envelope #10
Envelope DL
Envelope #9
Envelope #6
JIS B6
Hagaki
Ofuku-Hagaki
Youkei 2
Youkei 4
3-7/8 x 7-1/2 inches

4-1/8 x 9-1/2 inches
110 x 220 mm
3-7/8 x 8-7/8 inches
3-5/8 x 6-1/2 inches
128 x 182 mm
100 x 148 mm
148 x 200 mm
114 x 162 mm
105 x 235 mm
Custom
Cassette or
MP Tray
Ledger
Legal
Letter
ISO A3
ISO A4
ISO A5
ISO A6
Envelope C4
Envelope C5
ISO B5
JIS B4
JIS B5
Executive
Oficio II
Folio
Statement
8 kai
16 kai
Cassette: 148 x 210 mm to 297 x 432 mm
MP Tray: 70 x 148 mm to 297 x 450 mm
Size
11 x 17 inches
8-1/2 x 14 inches
8-1/2 x 11 inches
297 x 420 mm
210 x 297 mm
148 x 210 mm
105 x 148 mm
229 x 324 mm
162 x 229 mm
176 x 250 mm
257 x 364 mm
182 x 257 mm
7-1/4 x 10-1/2 inches
8-1/2 x 13 inches
210 x 330 mm
5-1/2 x 8-1/2 inches
273 x 394 mm
197 x 273 mm
Smoothness
The paper should have a smooth, uncoated surface. Paper with a rough
or sandy surface can cause blank spaces in the printed output. Paper
that is too smooth can cause multiple feeding and fogging problems.
(Fogging is a gray background effect.)
Basis weight
Basis weight is the weight of paper expressed in grams per square meter
(g/m). Paper that is too heavy or too light may cause feed errors or
paper jams as well as premature wear of the product. Uneven weight of
paper, namely uneven paper thickness may cause multiple-sheet
feeding or print quality problems such as blurring because of poor toner
fusing.
The recommended basis weight is:
Cassette: 60 to 120 g/m
MP tray: 60 to 220/g/m
PF-310: 60 to 120 g/m
PF-315: 60 to 200 g/m
PF 430: 60 to 120g/m
Paper Handling
2-5
Paper Weight Equivalence Table

The paper weight is listed in pounds (lb) and metric grams per square
meter (g/m). The shaded part indicates the standard weight.
U. S. Bond Weight (lb)
Europe Metric Weight (g/m)
16
60
17
64
20
75
21
80
22
81
24
90
27
100
28
105
32
120
34
128
36
135
39
148
42
157
43
163
47
176
53
199
Thickness
The paper used with the machine should be neither extremely thick nor
extremely thin. If you are having problems with paper jams, multiple
feeds, and faint printing, the paper you are using may be too thin. If you
are having problems with paper jams and blurred printing the paper may
be too thick. The correct thickness is 0.086 to 0.110mm (3.4 to 4.3 mils).
Moisture Content
Moisture content is defined as the percent ratio of moisture to the dry
mass of the paper. Moisture can affect the papers appearance, feed
ability, curl, electrostatic properties, and toner fusing characteristics.
The moisture content of the paper varies with the relative humidity in the
room. When the relative humidity is high and the paper absorbs
moisture, the paper edges expand, becoming wavy in appearance.
When the relative humidity is low and the paper loses moisture, the
edges shrink and tighten, and print contrast may suffer.
Wavy or tight edges can cause jams and alignment anomalies. The
moisture content of the paper should be 4 to 6%.
To ensure correct moisture content, it is important to store the paper in a
controlled environment. Some tips on moisture control are:
2-6
Store paper in a cool, dry location.

Keep the paper in its wrapping as long as possible. Re-wrap paper
that is not in use.
Paper Handling
Store paper in its original carton. Place a pallet etc. under the carton
to separate it from the floor.
After removing paper from storage, let it stand in the same room as
the machine for 48 hours before use.
Avoid leaving paper where it is exposed to heat, sunlight, or damp.
Paper Grain
When paper is manufactured, it is cut into sheets with the grain running
parallel to the length (long grain) or parallel to the width (short grain).
Short grain paper can cause feeding problems in the machine. All paper
used in the machine should be long grain.
Other Paper Properties

Porosity: Indicates the density of paper fiber.
Stiffness: Limp paper may buckle in the machine, resulting in paper
jams.
Curl: Most paper naturally tends to curl one way if left unpacked. When
paper passes through the fixing unit, it curls upward a little. To produce
flat printouts, load the paper so that the upward pressure from the
machine can correct their curling.
Electrostatic discharge: During the printing process the paper is
electrostatically charged to attract the toner. The paper must be able to
release this charge so that printed sheets do not cling together in the
Output Tray.
Whiteness: The contrast of the printed page depends on the whiteness
of the paper. Whiter paper provides a sharper, brighter appearance.
Quality control: Uneven sheet size, corners that are not square, ragged
edges, welded (uncut) sheets, and crushed edges and corners can
cause the machine to malfunction in various ways. A quality paper
supplier should take considerable care to ensure that these problems do
not occur.
Packaging: Paper should be packed in a sturdy carton to protect it from
damage during transport. Quality paper obtained from a reputable
supplier is usually correctly packaged.
Paper Handling
2-7
Special Paper
The following types of special paper can be used:
Paper type to be used
Paper type to be selected
Thin paper (60 to 64 g/m)

Thick paper (90 to 220 g/m)
Colored paper
Recycled paper
Overhead projector transparencies
Cardstock
Envelopes
Label
Vellum
Thick
Color
Recycled
Transparency
Cardstock
Envelope
Labels
Use paper that is sold specifically for use with copiers or printers (heatfusing type). When using transparencies, labels, envelopes, cardstock,
or thick paper, feed the paper from the MP Tray.
Since the composition and quality of special paper vary considerably,
special paper is more likely than white bond paper to give trouble during
printing. No liability will be assumed if moisture and so forth given off
during printing on special paper causes harm to the machine or operator.
Note Before purchasing any type of special paper, test a sample
on the machine and check that printing quality is satisfactory.
Transparency
Transparencies must be fed to the MP Tray. One transparency can be
loaded at a time.
Transparencies must be able to withstand the heat of fusing during the
printing process. The recommended transparency product is 3M PP2500
(Letter, A4).
Transparencies must be placed on the MP tray with the long edge
towards the printer.
MP Tray
When unloading transparencies (e.g., for clearing jams), hold them

carefully by the edges to avoid leaving fingerprints on them.
Labels
Labels must be fed to the MP Tray. One label can be loaded at a time.
The basic rule for printing on adhesive labels is that the adhesive must
never come into contact with any part of the machine. Adhesive paper
sticking to the drum or rollers will damage the machine.
2-8
Paper Handling
Label paper has a structure

comprising of three layers, as
shown in the diagram. The top
Top sheet (white
sheet is printed on. The
bond paper)
adhesive layer consists of
Adhesive
pressure-sensitive adhesives.
The carrier sheet (also called
Carrier sheet
the linear or backing sheet)
holds the labels until used.
Due to the complexity of its
composition, adhesivebacked label paper is particularly likely to give printing problems.
Adhesive label paper must be entirely covered by its top sheet, with no
spaces between the individual labels. Labels with spaces in between are
liable to peel off, causing serious paper jam problems.
Some label paper is manufactured with an extra margin of top sheet
around the edge. Do not remove the extra top sheet from the carrier
sheet until after printing is finished.
Acceptable
Unacceptable
Top sheet
Carrier sheet
The table below lists the specifications for adhesive label paper.
Item
Specification
Weight of top sheet

Composite weight
Thickness of top sheet
Composite thickness
Moisture content
44 to 74g/m (12 to 20 lb/ream)

104 to 151g/m (28 to 40 lb/ream)
0.086 to 0.107mm (3.9 to 4.2 mils)
0.115 to 0.145mm (4.5 to 5.7 mils)
4 to 6% (composite)
Postcards
Up to 10 postcards can be
loaded at a time. Fan the
stack of postcards and align
the edges before loading
them in the MP tray. Make
sure the postcards you are
going to set are not curled.
Feeding curled postcards
may cause paper jams.
Paper Handling
Rough
Edge
Rough
Edge
2-9
Some postcards have rough edges on the back (those are created when
the paper is cut). In this case, put the postcards on a flat place and rub
the edges with, for example, a ruler to smooth them.
Envelopes
Note If you use envelopes quite often, we recommend to use
optional paper feeder EF-310. (FS-3920DN/4020DN only).
Up to 5 envelopes can be loaded at a
time. Envelopes should be fed in the
face-up position, right edge first.
Since the composition of an
envelope is more complex than that
of ordinary paper, it is not always
possible to ensure consistent printing
quality over the entire envelope
surface.
Normally, envelopes have a diagonal
grain direction. Refer to Paper Grain
on page 2-7. This direction can
easily cause wrinkles and creases when envelopes pass through the
printer. Before purchasing envelopes, make a test print to check whether
the printer accepts the envelope.
Do not use envelopes that have an encapsulated liquid adhesive.

Avoid a long printing session for envelopes only. Extended envelope
printing can cause premature printer wear.
If jams occur, try setting less envelopes on the MP tray.
To avoid jams caused by curled envelopes, stack no more than 10
printed envelopes on the output tray.
Thick Paper
Fan the stack of paper and align the edges before loading them in the
MP tray. Align the edges before loading it in the MP tray. Some types of
paper have rough edges on the back (those are created when the paper
is cut). In this case, put the paper on a flat place and rub the edges once
or twice with, for example, a ruler to smooth them. Feeding rough edged
paper may cause paper jams.
Note If the thick paper
jams:
2-10
Load one sheet at

a time.
Hold the paper with
your hands when it
is being fed.
Load the paper in
the MP Tray with
the leading edge
raised up a few millimeters as shown in the illustration.
Paper Handling
Colored Paper
Colored paper should satisfy the same conditions as white bond paper.
Refer to Paper Specifications on page 2-2. In addition, the pigments
used in the paper must be able to withstand the heat of fusing during the
printing process (up to 200C or 392F).
Preprinted Paper
Preprinted paper should satisfy the same conditions as white bond
paper. Refer to Paper Specifications on page 2-2.The preprinted ink
must be able to withstand the heat of fusing during the printing process,
and must not be affected by silicone oil.
Do not use paper with any kind of surface treatment, such as the type of
paper commonly used for calendars.
Recycled paper
Select recycled paper that meets the same specifications as the white
bond paper except for whiteness. Refer to Paper Specifications on
page 2-2.
Note Before purchasing recycled paper, test a sample on the
machine and check that the printing quality is satisfactory.
Paper Handling
2-11
Paper Type
The printer is capable of printing under the optimum setting for the type
of paper being used.
A different paper type setting can be made for each paper source
including the MP tray. Not only can preset paper types be selected, but it
is also possible for you to define and select customized paper types.
Paper type can be changed using the printer driver and the operation
panel. The following types of paper can be used.
Paper source
Paper Weight
Paper Type
MP tray
Paper
Cassette
Range
Display in
Operation Panel
Duplex path
Plain
Yes
Yes
75 to 90g/m2
Normal2
Yes
Transparency
Yes
No
Transparency
Extra Heavy
No
Preprinted
Yes
Yes
75 to 90g/m
Normal2
Yes
Labels
Yes
No
105 to 135g/m2
Heavy1
No
Yes
105g/m2
Normal3
Yes
Bond
Yes
90 to
Recycled
Yes
Yes
75 to 90g/m
Normal2
Yes
Vellum
Yes
No
60 to 64g/m2
Light
No
105g/m2
Normal3
Yes
Rough
Yes
Yes
90 to
Letterhead
Yes
Yes
90 to 105g/m2
Normal3
Yes
Color
Yes
Yes
90 to 105g/m2
Normal3
Yes
90g/m2
Normal2
Yes
Prepunched
Yes
Yes
Envelope
Yes
No
170 to 220g/m2
Heavy3
No
No
Heavy3
No
Cardstock
Yes
75 to
170 to 220g/m
Thick
Yes
No
170 to 220g/m
Heavy3
No
High quality
Yes
Yes
75 to 90g/m2
Normal2
Yes
Yes
90g/m2
Normal2
Yes
Custom 1 (to 8)
Yes: Can be stored

a.
Yes
75 to
No: Cannot be stored
This is a paper type defined and registered by the user. Up to eight types of user settings may be defined. User
can also enable or disable the duplex path when using Custom. For more information, refer to Type Adjust
(Creating custom paper type) on page 7-33.
Select the paper thickness. For details, refer to Paper Weight (Setting
the paper weight) on page 7-33
2-12
Paper thickness
Range of paper weight
Light
Normal 1
Normal 2
Normal 3
Heavy 1
Heavy 2
Heavy 3
Extra Heavy
60 to 64g/m2
64 to 75g/m2
75 to 90g/m2
90 to 105g/m2
105 to 135g/m2
135 to 170g/m2
170 to 220g/m2
Transparencies
Paper Handling
Loading Paper
This chapter explains the procedure for loading paper in the cassette
and the MP tray.
Loading Paper into the Cassette

3-2
Loading Paper into MP (Multi-Purpose) Tray
3-6
Loading Envelopes into the MP Tray (FS-2020D/3920DN/4020DN
only)
3-8
Loading Paper
3-1
Loading Paper into the Cassette

The paper cassette can accommodate A6 (FS-2020D: A5) to A4/Letter
and Legal size paper and can hold approximately 500 sheets.
For FS-6970DN: The paper cassette can accommodate A5 to A3/Letter
and Legal size paper and can hold approximately 250 sheets.
A3
B4
A4R
B5
A4
A5
Pull the paper cassette all the way out of the printer.
For FS-6970DN : Remove the cassette cover.
IMPORTANT When pulling the cassette out of the printer, ensure

it is supported and does not fall out.
Standard paper sizes are marked on the inside of the paper

cassette.
3-2
Loading Paper
Turn the paper size dial so that the size of the paper you are going to
use appears in the paper size window.
Note When the paper size dial is set to OTHER the paper size
must be set into the printer on the operation panel. Refer to the
Custom Paper Size section in the Advanced Operation Guide.
Pull the release lever on the left side guide and slide to the desired
paper size.
If you are going to set paper that is longer than A4, pull out the
extension paper cassettes pushing the lock lever one by one and
adjust them to the desired paper size.
Pull the release lever and slide the paper stopper to the desired
paper size.
When using non-standard size paper, move the paper guides and
paper stopper all the way out, insert the paper, then adjust the paper
guides and paper stopper to the size of the paper. Adjust them so
that they are in light contact with the paper.
Loading Paper
3-3
Fan the paper, then tap it on a level surface to avoid media jams or
skewed printing.
Place the paper in the paper cassette. Ensure the side to be printed
is facing down and the paper is not folded, curled, or damaged.
Note Do not load more paper than will fit under the load limits
on the paper guides.
3-4
Set the stack of paper so that it is under the clips as shown.
Loading Paper
Insert the paper cassette into the slot in the printer. Push it straight in
as far as it will go.
There is a paper gauge on the right side of the front of the paper
cassette to indicate the remaining paper supply. When paper is
exhausted, the pointer will go down to the level of (empty).
Loading Paper
3-5
Loading Paper into MP (Multi-Purpose) Tray

The MP tray can accommodate the various paper sizes and can hold
approximately 100 sheets of paper.
3-6
Fan the media (paper/transparencies), then tap it on a level surface

to avoid media jams or skewed printing.
Pull the MP tray towards you until it stops.
Pull out the subtray.
Adjust the position of the paper guides on the MP tray. Standard

paper sizes are marked on the MP tray. For standard paper sizes,
slide the paper guides to the position marked correspondingly.
Loading Paper
Align the paper with the paper guides and insert as far as it will go.
Note If the paper is considerably curled in one direction, for

example, if the paper is already printed on one side, try to roll
the paper in the opposite direction to counteract the curl.
Printed sheets will then come out flat.
Correct
Incorrect
When loading envelope, place with the envelope flap closed and
keep the printing side face-up. Insert envelope against the guide
with the flap on the front or left side until they stop.
Loading Paper
Set the MP tray paper size on the printer's operation panel. Refer to
the Setting MP Tray Paper Size section in the Advanced Operation
Guide.
3-7
Loading Envelopes into the MP Tray

(FS-2020D/3920DN/4020DN only)
To print on the envelopes, follow the instructions below. If you use
envelopes quite often, we recommend to use optional paper feeder
EF-310. (FS-3920DN/4020DN only)
Open the rear unit.
Press the green buttons to change the thickness of paper.
CAUTION The fuser unit inside the printer is hot. Do not

touch it with your hands as it may result in burn injury.
3
4
Correct
Close the rear unit.

Follow the steps of Loading Paper into MP (Multi-Purpose) Tray on
page 2-6.
When loading envelope, place with the envelope flap closed and
keep the printing side face-up. Insert envelope against the guide
with the flap on the front or left side until they stop.
Correct
Incorrect
3-8
Loading Paper
This chapter explains how to start up the printer, print from your PC, and
use the application software included in the CD-ROM.
Connections
Changing Network Interface Parameters
Printing a Network Interface Status Page
Installing the Printer Driver
Printing from Application Software
Status Monitor
Uninstalling Software (Windows PC)
4-2
4-4
4-12
4-13
4-19
4-20
4-24
4-1
Connections
This section explains how to start up the printer. The figure shown below is
the overviews of connections between the printer and the computer.
Connecting the USB Cable

Follow the steps as below for connecting the USB cable.
Connect the USB cable (not included) to the USB interface

connector at the rear of this machine.
Note Use a USB cable with a rectangular Type A plug and a
square Type B plug. The USB cable should be shielded and
no longer than 5 meters (16 feet) long.
Connect the other end of the USB cable to the computer's USB
interface connector.
Connecting the Network Cable

Follow the steps as below for connecting the network cable.
Connect the shielded network cable (not included) to the computer

and the hub (concentrator).
Remove the cap at the rear of this machine and connect the other
side of the network cable to the network interface connector of the
machine and the hub.
Connecting the Parallel Cable

Follow the steps as below for connecting the parallel cable.
Connect the parallel cable to the parallel interface connector at the

rear of this machine.
Note Use a parallel printer cable that complies with IEEE
1284 standards. For optimum performance, install the printer
close to the PC. The connection cable should be shielded and
no longer than 3 meters (10 feet) long. The cable is solid
separately.
4-2
Connect the other side of the parallel cable to the computers

interface connector at the rear of this machine.
Connecting the Power Cord

Install the printer close to an AC wall outlet. If an extension cord is used, the
total length of the power cord plus extension should be 5 meters (16 feet) or
less.
Note Ensure the printer's power switch is off. Only use the power
cord supplied with the printer.
Connect the power cord to the Power Cord Connector at the rear of
the printer.
2
3
Connect the other end of the power cord to a power outlet.

Press the Power Switch to On ( | ). The printer begins to warm up.
IMPORTANT If you install the starter toner container and switch

on the power, after a moment the message Please
wait(Adding toner) is displayed. When the printer is first
switched on after toner installation, there will be a delay of
approximately 15 minutes before the printer gets ready to print.
Once the [Ready] indicator lights, printer installation is complete.
4-3
Changing Network Interface Parameters

This printer supports TCP/IP, TCP/IP (IPv6), NetWare, AppleTalk, IPP,
SSL Server, IPSec protocols, and Security Level. For more information,
refer to the Advanced Operation Guide.
Note After all network related settings have been done, turn the
machine OFF and ON again. This is mandatory to make the
settings effective.
TCP/IP, TCP/IP (IPv6) settings
Network
>TCP/IP
Off
>TCP/IP (IPv6)
Off
4-4
>
1
2
Press [MENU].
Press Z. Each time you press U or V, the selection changes. Refer

to the explanations below when specifying the settings.
Press U or V repeatedly until Network > appears.
Set this item to On when you connect to a network using TCP/IP.

Submenu has items including DHCP, IP Address, Subnet Mask,
Gateway and Bonjour.
Set this item to On when you connect to a network using TCP/IP

(IPv6). Submenu has items including RA(Stateless)and
DHCPv6.
TCP/IP
This section describes how to enable the TCP/IP protocol.
>TCP/IP
On
>
>>DHCP
Off
If TCP/IP is set to Off, use U or V to select On and press [OK].
Press Z. Each time you press U or V, the selection changes.
Display the item you want to set and press [OK]. A blinking question
mark (?) appears while you are setting DHCP and Bonjour. A
blinking cursor (_) appears while you are setting IP Address,
Subnet Mask and Gateway.
Press U or V to select On or Off as the setting for DHCP and

Bonjour.
>>IP Address
000.000.000.000
>>Subnet Mask
000.000.000.000
>>Gateway
000.000.000.000
>>Bonjour
Off
>>Subnet Mask
000.000.000.000
For the IP Address, Subnet Mask and Gateway settings, press

U or V to move the blinking cursor to the number you want to
change (000 to 255). Use Y and Z to move the cursor right and left.
Note Check with your network administrator for the network
address settings.
5
6
Press [OK].
Press [MENU]. The display returns to Ready.
4-5
TCP/IP (IPv6)
This section describes how to enable the TCP/IP (IPv6) protocol.
>TCP/IP (IPv6) >

On
>>RA(Stateless)
Off
If TCP/IP (IPv6) is set to Off, use U or V to selecto On and

press [OK].
mark (?) appears while you are setting RA(Stateless) and
DHCPv6.
Press U or V to select On or Off as the setting for

RA(Stateless) and DHCPv6.
>>DHCPv6
Off
>>RA(Stateless)
?Off
>>DHCPv6
?Off
Note Check with your network administrator for the network

address settings.
5
6
Press [OK].
NetWare, AppleTalk, IPP, SSL Server, IPSec and

Security Level settings
Security
4-6
>
1
2
Press [MENU].
Press U or V repeatedly until Security > appears.
Press Z. Each time you press U or V, the selection changes. Refer

to the explanations below when specifying the settings.
ID
_
If you are using NetWare, AppleTalk, IPP, SSL Server or

IPSec to connect to a network, you must enter an administrator ID
and press [OK]. The default setting is the numeric part of your
printer's model name. If you use FS-2020D, enter "2020".
Password
_
If you are using NetWare, AppleTalk, IPP, SSL Server or

IPSec to connect to a network, you must enter an administrator
password and press [OK]. The default setting is the numeric part of
your printer's model name. If you use FS-2020D, enter "2020".
>NetWare
On
>AppleTalk
On
>IPP
Off
>SSL Server
Off
>IPSec
Off
>
Set this item to On when you connect to a network using NetWare.

In submenu, frame mode can be selected from Auto, 802.3,
Ethernet-II, SNAP and 802.2.
AppleTalk must be activated (On) for networking with Macintosh

computers.
Set this item to On when you connect to a network using IPP.
Set this item to On when you connect to a network using SSL

Server. Submenu has items including DES, 3DES, AES, IPP over
SSL and HTTPS.
Set this item to On when you connect to a network using IPSec.
Continued on next page.
4-7
Set the Security Level to High.
>Security Level
High
NetWare
This section explains the procedure for enabling NetWare.
>NetWare
On
>>Frame Type
Auto
>>Frame Type
?Auto
>
Enter the administrator ID and password. Then, if NetWare is set to

Off, use U or V to select On and press [OK].
Press Z.
Press [OK]. A blinking question mark (?) appears. Each time you
press U or V, the selection changes.
4
5
Display the item you want to set and press [OK].
>>Frame Type
?802.3
>>Frame Type
?Ethernet-II
>>Frame Type
?802.2
>>Frame Type
?SNAP
4-8
AppleTalk
This section explains the procedure for enabling AppleTalk.
>AppleTalk
On
>AppleTalk
?On
Enter the administrator ID and password. Then, if AppleTalk is set

to Off, use U or V to select On.
Press [OK]. A blinking question mark (?) appears.
3
4
Press [OK] again.

IPP
This section explains the procedure for enabling IPP.
>IPP
On
>IPP
?On
Enter the administrator ID and password. Then, if IPP is set to Off,

use U or V to select On.
3
4
Press [OK] again.

4-9
SSL Server
This section explains the procedure for enabling SSL Server.
>SSL Server
On
>>DES
Off
Enter the administrator ID and password. Then, if SSL Server is

set to Off, use U or V to select On and press [OK].
mark (?) appears.
4
5
6
Select On or Off using U or V.
>>3DES
Off
>>AES
Off
>>IPP over SSL

Off
>>HTTPS
Off
>>DES
?Off
Press [OK].
IPSec
This section explains the procedure for enabling IPSec.
>IPSec
On
>IPSec
?On
4-10
Enter the administrator ID and password. Then, if IPSec is set to

Off, use U or V to select On.
3
4
Press [OK] again.

Security Level
>Security Level
High
Security Level is primarily a menu used by service personnel for

maintenance work. There is no need for customers to use this menu.
4-11
Printing a Network Interface Status Page

You can print out a status page for the network interface. The network
status page shows the network addresses, and other information under
various network protocols about the network interface.
Adjust/Maintenance
Adjust/Maintenance is used to adjust the print quality and to carry out
printer maintenance.
The options available in Adjust/Maintenance are as follows:
Restart Printer
Service
IMPORTANT Service is primarily a menu used by service

personnel for maintenance work. There is no need for customers to
use this menu.
Adjust/
Maintenance
>
>>Print Network
Status Page ?
4-12
1
2
Press [MENU].
3
4
5
6
Press Z while Adjust/Maintenance > is displayed.
Press U or V repeatedly until Adjust/Maintenance > appears.
Press U or V repeatedly until >Service > appears.

Press Z.
Press U or V repeatedly until >>Print Network Status Page
appears.
Press [OK]. A question mark (?) appears.
8
9
Press [OK]. Processing appears and a status page is printed out.

When printing ends, the display returns to Ready.
Installing the Printer Driver

According to the instructions of the Installation Guide, connect the PC to
the printer and turn on them to install the printer driver. For more
information on printer driver, refer to the KX Driver User Guide in the CDROM.
Installing the Printer Driver on Windows PC

This section explains how to install the printer driver in Windows Vista.
Note To install the printer driver, you must log on with
administrator privilege.
Ensure the printer is plugged in and connected to the computer's

USB or Network port before installing software from the CD-ROM.
Note If a Plug and Play window like that shown at left
appears, click Cancel.
Insert the CD-ROM (Product Library) into the CD-ROM drive. If

AutoPlay screen appears, click Run Setup.exe. The Notice screen
appears.
Note If the installation program fails to launch, use Windows
Explorer to access the CD-ROM and select Setup.exe.
Select View License Agreement to read the information and select

Accept to proceed.
Click Install Software. Installation Method screen appears.

Note In Windows XP, click Install Software to start the
Installation wizard. Click Next to display the Installation
Method screen.
Select Express Mode or Custom Mode as the installation method.
Express Mode: If the printer is connected via USB or a network and

is turned on, the installer detects the printer. Select Express Mode to
perform a standard installation.
4-13
Custom Mode: This option allows you to select items to be installed

as required and to specify the port.
Proceed the section below according to the installation method.
Express Mode
When selecting Express Mode, printer driver and fonts are installed.
After installing with this mode, the other utilities can be added using
Custom Mode.
On Installation Method screen, click Express Mode. The installer

searches the connected printers on Discover Printing System
screen. If no printer is discovered, ensure the printer is plugged in
and connected to the computer's USB or Network port, then check
Refresh to search printers again.
Note If Found New Hardware window appears, click Cancel.
Select the printer you want to install, and click Next.
Confirm the settings and click Install. Printer driver installation

starts.
Note During any point in the installation process, if the
Windows Security warning dialog box appears, click Install
this driver software anyway.
If the Hardware Installation screen appears in Windows XP,
click Continue Anyway.
4-14
Installation Completed screen appears. Click Finish to return to the

main menu.
Custom Mode
When selecting Custom Mode, printer port and utilities are changed
as necessary.
On Installation Method screen, click Custom Mode.
On Driver tab and Utility tab of the Custom Installation screen, select
the printer driver and utilities you want to install, and click Next.
Select the printer you want to install, and click Next.

Note When you want to add or edit the port connected to the
printer, select the printer and Custom Select, then click Next.
Add Standard TCP/IP Printer Port Wizard appears. Follow
the steps in the wizard to add or edit the port.
Confirm the settings and click Install. Printer driver installation

starts.
Note During any point in the installation process, if the
Windows Security warning dialog box appears, click Install
this driver software anyway.
If the Hardware Installation screen appears in Windows XP,
click Continue Anyway.
Installation Completed screen appears. Click Finish to return to the

main menu.
4-15
Installing the Printer Driver on Mac OS

This section explains how to install the printer driver in Mac OS.
1
2
Turn on the printer and the Macintosh.
3
4
Double-click the CD-ROM icon.
Double-click Kyocera OS X x.x.
The printer driver installation program starts up.
Choose Select Destination, Installation Type and then install the

printer driver as directed by the instructions in the installation
software.
Insert the included CD-ROM (Product Library) into the CD-ROM

drive.
Double-click either OS X 10.2 and 10.3 Only or OS X 10.4 or
higher depending on your Mac OS version.
Note In addition to Easy Install, the Installation Type

options include Custom Install, which allows you to specify
the components to be installed.
IMPORTANT In the Authenticate screen, enter the name and

password used to log in to the operating system.
This completes the printer driver installation. Next, specify the print
settings.
If an IP or AppleTalk connection is used, the settings below are
required. If a USB connection is used, the printer is automatically
recognized and connected.
4-16
Open System Preferences and click Print & Fax.
Click the plus symbol (+) to add the installed printer driver.
10 Click the IP icon for an IP connection and then enter the IP address
and printer name. When you click the AppleTalk icon for an
AppleTalk connection, enter the printer name.
11 Select the installed printer driver and click Add.
4-17
12 Select the options available for the printer and click Continue.
13 The selected printer is added. This completes the printer setup

procedure.
4-18
Printing from Application Software

The steps required to print a document created with an application are
explained below. You can select the printing paper size and output
destination.
Note You can also select the various settings by clicking
Properties to open the Properties dialog box.
1
2
Load the paper required into the paper cassette.

From the application File menu, select Print. The Print dialog box
appears.
Click the drop-down list of printer names. All the installed printers are
listed. Click the name of the printer.
Use Number of copies to enter the number of copies required. Up to

999 copies can be printed.For Microsoft Word, we recommend that
you click Options and specify Use printer settings for the Default
tray.
3
4
To start printing, click OK.
4-19
Status Monitor
The Status Monitor monitors the printer status and provides an ongoing
reporting function. It also allows you to specify and modify settings for
printers not included in the KX Driver.
The Status Monitor is installed automatically during KX Driver
installation.
Accessing the Status Monitor

Use either of the methods listed below to launch the Status Monitor.
Launch when printing starts:

When you specify a printer and start a print job, one Status Monitor
is launched for each printer name. If Status Monitor startup is
requested from multiple printers, Status Monitors are launched for
each printer that issues the request.
Launch from the KX Driver properties:
Click Print Settings in Properties dialog box. Select Advanced tab
and click Status Monitor to launch the Status Monitor.
Exiting the Status Monitor

Use either of the methods listed below to exit the Status Monitor.
Exit manually:
Right-click the Status Monitor icon in the taskbar and select Exit in
the menu to exit the Status Monitor.
Exit automatically:
The Status Monitor automatically shuts down after 5 minutes if it is
not being used.
Screen Overview
The screen overview of the Status Monitor is as follows.
Pop-up window
3D View
Status Monitor icon
Pop-up window
If an information notification event occurs, a pop-up window appears.
This window only appears when the 3D View is open on the desktop.
3D View
This shows the status of the monitored printer as a 3D image. You can
choose whether to show or hide the 3D view from the menu displayed
when you right-click the Status Monitor icon.
4-20
If an information notification event occurs, the 3D view and an alert

sound are used to notify you. For information on the sound notification
settings, refer to Status Monitor Settings on page 4-22.
Status Monitor icon

The Status Monitor icon is displayed in the taskbar notification area
when the Status Monitor is running. When you position the cursor over
the icon, the printer name appears.
4-21
Status Monitor Settings

The Status Monitor has two tabs to configure its settings. Use the
Preference option to set up the Status Monitor.
Sound Notification Tab

The Event Notification tab contains the following items.
IMPORTANT To confirm the settings on Sound Notification tab, the

computer requires the sound capabilities such as sound card and
speaker.
Enable Event Notification
Select to enable or disable monitoring the events in Available events.
Sound file
A sound file can be selected if you require an audible notification. Click
Browse to search for the sound file.
Use Text to speech
Select this check box to enter text you would like to hear played for
events. Although a sound file is unnecessary, this function is applicable
for Windows XP and Windows Vista.
To use this function, follow these steps.
1
2
Select Enable Event Notification.
Click Browse to notify the event by sound file.
Select an event or sound file to use with the text to speech function
in Available events.
Note The available file format is WAV.

Select Use Text to speech to speech the text entered in Text to
speech box when an event occurred.
4-22
Click
to confirm the sound or text is played correctly.
Appearance Tab
The Appearance tab is contains the following items.
Enlarge window
Doubles the size of the Status Monitor window.
Always on top
Positions the Status Monitor in front of other active windows.
Transparency
Displays the Status Monitor as a transparent window.
4-23
Uninstalling Software (Windows PC)

The software can be uninstalled (removed) using the CD-ROM (Product
Library) supplied with the printer.
IMPORTANT On Macintosh computers, because the printer settings

are specified using a PPD (PostScript Printer Description) file, the
software cannot be uninstalled using the CD-ROM (Product Library).
1
2
Exit all active software applications.
Following the procedure used to install the printer driver, click

Remove Software. The Kyocera Uninstaller wizard appears.
4
5
Select the software package to remove.
Insert the enclosed CD-ROM (Product Library) into the CD-ROM

drive.
Click Uninstall.
Note In Windows Vista, Remove Driver and Package screen
appears. Select Remove driver and driver package, and
click OK.
The uninstaller starts.
6
7
4-24
When Uninstall complete screen appears, click Next.

Select whether you restart your computer or not, click Finish.
Maintenance
This chapter explains how to replace the toner container and clean the
printer.
General Information
Toner Container Replacement
Cleaning the Printer
Prolonged Non-Use and Moving of the Printer
Maintenance
5-2
5-2
5-7
5-8
5-1
General Information
This chapter describes basic maintenance tasks you can perform for the
printer. You can replace the following component according to the
printer's display:
Toner Kits
Waste Toner Box
Also, the internal parts need periodic cleaning.

Note Information Collection on Memory Chips - The memory chip
attached to the toner container is designed to improve
convenience for the end user; to support the recycling operation of
empty toner containers; and to gather information to support new
product planning and development. The information gathered is
anonymous - it cannot be associated to any specific individual and
the data is intended to be used anonymously.
Toner Container Replacement

Frequency of toner container replacement
The life of the toner containers depends on the amount of toner required
to accomplish your printing jobs. According to ISO/IEC 19798 and
EcoPrint switched off the toner container can print as follows (A4/Letter
paper is assumed): 20,000 pages (FS-4020DN); 15,000 pages
(FS-3920DN/FS-6970DN); 12,000 pages (FS-2020D).
You can print a status page to check how much toner remains in the
toner container. The Toner Gauge in the consumables status section on
the status page shows a progress bar, which roughly represents how
much toner is left in the toner container.
First Toner Container

The toner container packed with the new printer has to fill up the system
when operating the first time. Therefore only 50% of the first toner kits
can be used for printing. The toner container supplied with the printer will
print approximately:
FS-2020D: 6.000 pages
FS-3920DN/FS-6970DN: 7.500 pages
FS-4020DN : 10.000 pages.
Toner Kits
For best results, we recommend that you only use genuine Kyocera
Parts and Supplies. Should any damage be caused by the application of
a toner other than the original. Kyocera Mita toner, then this damage is
excluded from the guarantee.
A new toner kit contains the following items:
Toner Container
Plastic waste bag for old toner container and waste toner box
Waste toner box
Installation Guide
Note Do not remove the toner container from the carton until you
are ready to install it in the printer.
5-2
Maintenance
Understanding Messages Requesting Toner

Container Replacement
The printer displays messages at two stages of toner usage. This
message is automatically alternated with the other printer message
(such as Ready):
When the printer becomes low on toner, the printer displays the
message Toner low as the first caution. Note the replacement is
not always necessary at this stage.
If you ignore the above message and continue printing, the printer
displays the message Replace toner - just before the toner is
used up. The toner container must be replaced immediately. After
the cleaning is finished, however, the message does not
automatically change to Ready. To restart printing, you must press
[GO] and make the printer ready.
In either case, replace the toner container, refer to Replacing the Toner
Container on page 5-3.
Replacing the Toner Container

This section explains how to replace the toner container. When replacing
the toner container, always replace the waste toner box at the same
time. If this box is full, the printer may be damaged or contaminated by
the waste toner that may spill over the box.
CAUTION Do not attempt to incinerate the Toner

Container. Dangerous sparks may cause burns.
IMPORTANT During toner container replacement, temporarily move
storage media and computer supplies (such as floppy disks) away
from the toner container. This is to avoid damaging media by the
magnetism of toner.
IMPORTANT Kyocera Mita Corporation is not liable against any
damages or problems arising from the use of toner containers other than
those designated as original Kyocera toner containers. For optimum
performance, it is also recommended to use only the Kyocera toner
containers which are specifically intended for use in your country or
region. If the toner container for another destinations is installed, the
printer will stop printing.
Note You do not have to turn printer power off before starting
the replacement. Any data that may be processing in the printer
will be deleted if you turn the printer power off.
Maintenance
Open the top cover.
5-3
Push lock lever to the right and pull out the toner container.
Put the old toner container in the plastic bag (contained in the toner
kit) and discard it later according to the local code or regulations for
waste disposal.
4
5
Take the new toner container out of the toner kit.
Remove the label from the toner container.
Set the new toner container in the printer and push down on the top
of the toner container to install it firmly in place as shown at the left.
Close the top cover.
Shake the new toner container at least 10 times as shown in the

figure in order to distribute the toner evenly inside the container.
Proceed to the next section.
5-4
Maintenance
Replacing the Waste Toner Box

When replacing the toner container, the used waste toner box in the
printer should also be replaced with the new one from the new toner
kit. A new waste toner box is included with the toner kit. The printer
will not operate without replacing the waste toner box.
Open the left cover. While holding the waste toner box, press the
lock lever and then gently remove the waste toner box.
Note Remove the waste toner box as gently as possible so as
not to scatter the toner inside. Do not let the opening of the
waste toner box face downward.
Maintenance
Close the cap to the old waste toner box after removing the box from
the printer.
To prevent toner from spilling, put the old waste toner box in the
plastic bag (contained in the toner kit) and discard it later according
to the local code or regulations for waste disposal.
5-5
Open the cap of the new waste toner box.
Insert the new waste toner box as shown at the left. When the box is
set correctly, it will snap into place.
Make sure that the waste toner box is correctly inserted and close
the left cover.
After replacing the toner containers and the waste toner box, clean
the internal parts. For instructions, refer to Cleaning the Printer on
page 5-7.
5-6
Maintenance
Cleaning the Printer

To avoid print quality problems, the interior of the printer must be
cleaned with every toner container replacement.
Maintenance
Open the top cover and MP tray.
Lift the developer unit together with the toner container out of the
printer.
Use a lint free cloth to clean dust and dirt away from the registration
roller (metal).
Insert the developer unit together with the toner container, back into
the machine.
Close the top cover and MP tray.
5-7
Open the left cover. Use a lint free cloth to clean dust and dirt away
from the vents.
Close the left cover.
Use a lint free cloth to clean dust and dirt away from the vent on the
right side of the machine.
Prolonged Non-Use and Moving of the Printer

Prolonged Non-use
If you ever leave the printer unused for a long period of time, remove the
power cord from the wall outlet.
We recommend you consult with your dealer about the additional actions
you should take to avoid possible damage that may occur when the
printer is used next time.
Moving the Printer

When you move the printer:
Move it gently.
Keep it as level as possible to avoid spilling toner inside the printer.
Be sure to consult a service technician before attempting long
distance transportation of the printer.
WARNING If you ship the printer, remove and pack the

developer unit in a plastic bag and ship them separately
from the printer.
5-8
Maintenance
Troubleshooting
This chapter explains how to handle printer problems, understand

messages, and clean paper jams.
General Guidelines
Print Quality Problems
Error Messages
Ready, Data, and Attention Indicators
Clearing Paper Jams
6-2
6-3
6-5
6-11
6-12
If a problem cannot be corrected, contact your service technician.
Troubleshooting
6-1
General Guidelines
The table below provides basic solutions for problems you may
encounter with the printer. We suggest you consult this table to
troubleshoot the problems before calling for service repairs.
Symptom
Check Items
Corrective Actions
Print quality is poor.

Text is missing on the
Windows test page.
Paper is jammed.
Nothing lights on the
operation panel even
when power is turned on
and the fan makes no
noise.
Refer to Print Quality Problems on page 6-3.

This is a problem specific to the Windows OS. It is
not a printer problem. It does not affect print quality.
Refer to Clearing Paper Jams on page 6-12.
Connect both ends of the power cord securely. Try
replacing the power cord. Refer to Installation Guide
for more information.
Refer to the Installation Guide for more information.
Check the power cord is property

plugged into power outlet.
Check the power switch is in the

On ( | ) position.
The printer prints a status Check program files and application
page but data from the
software.
computer is not being
printed.
Check the interface cable.
Vapor is emitted at the

rear of the printer.
Check if the temperature is low near

the location of the printer, or if the
paper that is being used has been
exposed to humidity.
Try printing another file or using another print

command. If the problem occurs with a specific file or
application, check the printer settings for that
application.
Connect both ends of the interface cable securely.
Try replacing the printer cable. Refer to the
Installation Guide for more information.
Depending on the operating environment of the
printer and the condition of the paper, heat
generated during printing can evaporate water
moisture in the printed paper, emitting vapor from the
printer. In this case, printing can be continued
without any problem.
To correct this, increase the temperature in the room,
and use paper that has been stored in a dry place.
Tips
Printer problems may be solved easily by following the tips below. When
you have encountered a problem that following the above guidelines will
not solve, try the following:
6-2
Turn the printer power off and wait for several seconds. Then, turn
on the printer.
Restart the computer you are using to send print jobs to the printer.
Obtain and use the latest version of the printer driver. The latest
versions of printer drivers and utilities are available at:
http://www.kyoceramita.com/download/.
Make sure that the procedures for printing are correctly followed in
the application software. Consult the documentation supplied with
the application software.
Troubleshooting
Print Quality Problems

The tables and diagrams in the following sections define print quality
problems and the corrective action you can conduct to solve the
problems. Some solutions may require cleaning or replacing parts of the
printer.
If the suggested corrective action will not solve the problem, call for
service.
Printed Results
Corrective Action
Completely blank printout
Check the toner container.

Open the top cover and check that the toner container is correctly
installed in the printer. For more information on installing the toner
container, Refer to Toner Container Replacement on page 5-2.
Check that the application software is correctly operated.
Black or white vertical streaks
Check the operation panel for toner.

If the Toner low message is displayed, install a new toner kit. To
replace the toner container, refer to Toner Container Replacement on
page 5-2.
Faint or blurred printing
Check the EcoPrint settings.

When this setting is On, switch it to off on the operation panel.
Make sure the paper type setting is correct the paper being used.
Check the operation panel for toner. If the Toner low message is
displayed, install a new toner kit. To replace the toner container, refer
to Toner Container Replacement on page 5-2.
Troubleshooting
6-3
Printed Results
Corrective Action
Gray background
Check the operation panel.

If the Toner low message is displayed and [Attention] indicator is
flashing, install a new toner kit. To replace toner, refer to Toner
Container Replacement on page 5-2
Check the print density.
Display the print menu from the operation panel and select a lighter
density setting.
Dirt on the top edge or back of the

paper
Clean the parts in the paper paths-such as the paper cassette, etc.
Printing incomplete or out of position
Check that the application software is correctly operated.

Refer to Tips on page 6-2.
6-4
Troubleshooting
Error Messages
The following table lists errors and maintenance messages that you can
be dealt with by yourself.
If Call service or Error.Power off. is displayed, turn off the
printer then turn it back on to see if the printer has recovered. If the
printer has not recovered, turn off the printer, disconnect the power cord,
and contact your service representative or authorized service center.
Some errors cause the alarm to sound. To stop the alarm, press
[Cancel].
Message
Account error ##
Press GO
Add paper MPTray
Call service
F###:
Call service
####:0123456
Corrective Action
This message is displayed when the Job Accounting function is enabled and an attempt to
specify job accounting settings or to register or delete an account fails. To return the printer to
the print-ready status, press [GO].
The paper has run out in the paper source displayed. Supply paper according to the paper
source displayed (paper cassettes, MP tray, or optional paper feeders).This message is
displayed alternately with messages indicating the printer status, such as, Ready, Please
wait, and Processing.
F### represents a controller error (#=0, 1, 2, ...). Call for service. The printer does not
operate when this message is displayed.
#### represents a mechanical error (#=0, 1, 2, ...). Call for service. The printer does not
operate when this message is displayed. The total number of pages printed is also indicated,
e.g. 0123456.
Displayed when data is being canceled.
Canceling data
Cassette #
not loaded
Change envelope
switch position
Check
cassette #
The corresponding paper cassette is not installed. Install the cassette. The cassette number
can be 1 (topmost) to 4 (bottom).
Displayed when the paper type does not match the envelope switch setting.
(FS-2020D/3920DN/4020DN only)
This message is displayed when a paper lift error has occurred in the paper sources
cassette. Pull out the cassette for the paper source displayed (either the paper cassettes or
optional paper feeders) and check if the paper is loaded correctly.
(FS-2020D/3920DN/4020DN only)
The message Call service is displayed when this error occurs repeatedly.
Check waste
toner box
This message warns following two cases. Install the new waste toner box.
The waste toner box is not installed.
The waste toner box is full.
Clean printer
Press GO
Please clean the inside of the printer. Refer to Cleaning the Printer on page 5-7.
This message will be displayed when replacing the toner container after the message
Replace toner Clean printer is displayed. After cleaning the inside of the printer,
press [GO] and the printer will be ready for printing.
The left cover of the printer is open. Close the printer left cover.
Close
left cover
Troubleshooting
6-5
Message
Corrective Action
The rear unit of the printer is open. Close the printer rear unit.
Close
rear unit
The top cover of the printer is open. Close the printer top cover.
Close
top cover
Device busy
Duplex disabled
Press GO
Enter Account
Envelope mode
Error.Power off.
F###
Error.Power off.
F000
Exceeded Max.out
Press GO
This message is displayed when Remove Device was selected while a USB memory was
being used.
The previous screen is displayed again 1 or 2 seconds.
You attempted to print with a paper size and paper type that cannot be used for duplex
printing. Press [GO] to print onto one-side of the paper only.
You can select an alternative paper size and type by pressing the U or V. You can also
press [MENU] and change the tray setting inside the menu, which will automatically cancel
the error and output resumes. At the same time [ATTENTION] indicator will light up and
[READY] indicator will start flashing.
An account code must be entered. This message is displayed if you try to print from the
operation panel (e.g. printing a status page or using the Job Retention function) when the Job
Accounting function is enabled. For more information, refer to Job Accounting (Job
Accounting selection/setting) section in the Advanced Operation Guide.
Displayed when the envelope switches are set to envelope mode.
(FS-2020D/3920DN/4020DN only)
Turn the power switch off and then back on again. If this message still remains, turn the
power switch off, and contact your service representative or authorized service center.
The printer controller and operation panel cannot exchange data. Turn the printer off and
unplug it from the mains power supply. Then contact your service representative or
authorized service center. See the back page of this manual for the relevant phone numbers.
This message is displayed when the Job Accounting function is enabled and an attempt has
been made to exceed the print limit set for each account. To return the printer to the printready status, press [GO].
For more information, refer to Job Accounting (Job Accounting selection/setting) section in
the Advanced Operation Guide.
The hard disk installed in the printer is not formatted, and therefore cannot be read or written.
Format error
Hard disk
Format error
Memory card
Hard disk err ##
Press GO
ID error
6-6
The CF card inserted in the printer is not formatted, and therefore cannot be read or written.
To format a CF card, follow the procedure in Memory Card (Using the memory card) section
in the Advanced Operation Guide.
A hard disk error has occurred. Look at the error code given in place of ## and refer to
Storage Error Codes on page 6-10. To ignore the hard disk error, press [GO].
The user ID entered for a private job is not correct. Check the user ID that you specified on
the printer driver. For more information, refer to Job Box section in the Advanced Operation
Guide.
Troubleshooting
Message
Corrective Action
Illegal Account
Press GO
This message is displayed when the Job Accounting function is enabled and no account is
set for a transmitted print job or the specified account is not registered (the incorrect account
is set). To return the printer to the print-ready status, press [GO].
Install MK
Replace Maintenance Kit which is displayed on the message display. Replacement of the
maintenance kit is necessary at every 300,000 pages of printing and requires professional
servicing. Contact your service technician.
Job not stored
Printing using the Job Box function failed because there was insufficient space available on
the hard disk or RAM disk, or because the RAM disk was disabled when demounting the hard
disk. To print an error report and return the printer to the print-ready status, press [GO].
Press GO
Job restricted
Press GO
KPDL error
##
Press GO
Load Cassette #
(A4)/(PLAIN)
Load MP Tray
(A4)/(PLAIN)
This message is displayed when printing was attempted, despite the Job Account function
being on with Restriction applied as the job limit for each job account.
To return the printer to the print-ready status, press [GO].
Current print processing cannot continue because of occurrence of KPDL error which is
categorized by ##. To print out an error report, display >>Error Report from the menu
system, and select On. Press [GO] to resume printing. You can abandon printing by pressing
[Cancel].
If Auto Error Clear is set to On, printing will be automatically resumed after a preset period of
time.
The paper cassette matching the paper size and paper type of the print job is empty. Load
paper into the paper cassette as displayed in place of #. Printing resumes automatically.
If you want to print from a different paper source, press U or V to select the alternative paper
source, and then press [OK].
When you press [MENU], Paper Settings > appears. Press U or V to select the paper
size and type of the paper source. Press [OK] to display Use alternative? and then
press [OK]. Printing starts using the specified the paper source.
There is no paper cassette installed in the printer that matches the paper size and paper type
of the print job. Set paper in the MP tray. Printing resumes automatically. (Note that feeding
the paper having a paper size which does not match the current paper size from the MP tray
can cause paper jam.)
If you want to print from a different paper source, press U or V to select the alternative paper
source, and then press [OK].
When you press [MENU], Paper Settings > appears. Press U or V to select the paper
size and type of the paper source. Press [OK] to display Use alternative? and then
press [OK]. Printing starts using the specified the paper source.
This message is displayed when Low was selected in Security Level.
Low security
Match envelope
switches
Memory overflow
Press GO
Troubleshooting
Displayed when either of the envelope switches is not pressed. To print on the envelope,
press the both switches. (FS-2020D/3920DN/4020DN only)
The total amount of data received by the printer exceeds the printers internal memory.
Try adding more memory. Press [GO] to resume printing. You can abandon printing by
pressing [Cancel].
time.
6-7
Message
MemoryCard err##
Press GO
MemoryCard err20
Missing
developer unit
No multi copies
Press GO
Corrective Action
A CompactFlash card error has occurred. Look at the error code given in place of ## and
refer to CompactFlash (CF) Card and USB Flash Memory Errors on page 6-10. To ignore the
CompactFlash card error, press [GO].
The CompactFlash card is accidentally inserted and removed from the printers slot during
the printer is on. Turn the power switch off, insert the CompactFlash card, and then turn on
the printer again.
The developer unit is either not installed or incorrectly inserted. Insert the developer unit
securely.
Multiple copies cannot be printed because the RAM disk is disabled or the hard disk is not
installed. There is no available RAM disk or hard disk space. Delete unnecessary files. Press
[GO] to print error report.
Displayed when the installed toner is the original Kyocera product.
Original toner
installed
Paper jam
###############
A paper jam has occurred. The location of the paper jam is indicated in place of the #s. For
details, refer to Clearing Paper Jams on page 6-12.
The selected cassette is being prepared. (FS-2020D/3920DN/4020DN only)
Paper loading
Paper path error
Print overrun
Press GO
RAM disk error##

Press GO
Replace toner
Clean printer
Size error
(Cassette)/(A4)
When one or more optional feeders are installed, this message will appear if any of the paper
feeders or the printer cassette upper than the selected one is not properly closed.
The print job transferred to the printer was too complex to print on a page. Press [GO] to
resume printing. (A page break may be automatically inserted in some places.)
You can abandon printing by pressing [Cancel].
time.
A RAM disk error has occurred. Look at the error code given in place of ## and refer to
Storage Error Codes on page 6-10. To ignore the RAM disk error, press [GO].
Toner has run out in the toner container. Replace the toner container using a new toner kit.
The printer does not operate when this message is displayed.
The paper size of the actual paper on which the print job was printed is shorter than the
intended paper size (the paper size specified in the paper source or specified by the user).
This error is released to restart paper supply either by placing the requested size paper in the
requested paper source or by matching the paper size setting for the paper supply to the
actually printed paper size.
You can also temporarily restart paper supply by pressing [GO]. At the same time
[ATTENTION] indicator will light up and [READY] indicator will start flashing.
Replace the toner container using a new toner kit.
Toner low
Top tray
paper full
6-8
The top tray has become full. You must remove all printed pages from the top tray. When the
printer detects that the top tray is empty again, the printer will continues printing into the top
tray.
Troubleshooting
Message
Corrective Action
Unknown toner
Displayed when the installed toner is not the original Kyocera product. Install original Kyocera
toner. Install the toner container.
installed
Unknown toner
This message is displayed if the installed toner container's regional specification does not
match the printer's.
installed PC
USB memory err##

Press GO
Use alternative?
Cassette 1
Wrong Account
Wrong ID
Wrong Password
Troubleshooting
An error has occurred in the USB memory device. Look at the error code given in place of ##
and refer to CompactFlash (CF) Card and USB Flash Memory Errors on page 6-10. To return
the printer to the print-ready status, press [GO].
When the cassette does not contain any paper that matches the print data (paper size and
type), this message allows you to specify an alternative cassette to use instead. A paper
source number is only displayed when an optional paper feeder is installed. To print from a
different paper source, press U or V to select the alternative paper source, and then press
[OK].
Displayed when an attempt is made to register an account in the Job Accounting menu by
entering an account code that already exists.
The ID or Password entered for the Security, Administrator, or Job Accounting function is not
correct. Check the ID or Password.
For more information,refer to Security section, Admin (Administrator settings) section, and
Job Accounting (Job Accounting selection/setting) section in the Advanced Operation Guide.
The password does not match the password set. Enter the correct password. For more
information, refer to Security section, Admin (Administrator settings) section, and Job
Accounting (Job Accounting selection/setting) section in the Advanced Operation Guide.
6-9
Storage Error Codes

Hard Disk Errors
Code
Meaning
01
Hard disk format error. If this error recurs even if the power has been turned
off and then on, reformat the hard disk.
02
The disk system is not installed. Recheck the requirements for using the
system and the devices.
04
There is no available hard disk space. Delete unnecessary files, etc., in

order to free up space.
05
The specified file does not exist in the hard disk.
06
There is no memory available to the hard disk system. Increase the

available memory.
10
Formatting is not possible because host data is being spooled on the hard
disk. Wait until the hard disk is ready, and then format.
97
The number of permanent code jobs that can be stored reached the limit
value, and no more can be saved. Either delete some unnecessary jobs,
etc., or increase the limit.
98
An unreadable page was found in a job (The job is damaged.).
99
A print job for the specified ID does not exist in the hard disk.
CompactFlash (CF) Card and USB Flash Memory Errors
6-10
Code
Meaning
01
The printer does not support the CF card inserted, or the CF card is broken.
Insert the correct CF card.
For more information, refer to Memory Card (Using the memory card) section
in the Advanced Operation Guide.
02
The CF card is not installed. Recheck the requirements for using the system
and the CF card.
03
The CF card is write protected. Check the CF card's status.
04
There is not enough space in the CF card. Delete unnecessary files or use a
new CF card.
05
The specified file is not on the CF card or the USB flash memory.
06
There is not enough printer memory to support the CF card system. Increase
printer memory.
50
The USB flash memory is write protected, or invalid. Check the USB flash
memorys status.
Troubleshooting
RAM Disk Errors

Code
Meaning
01
Format error. Try turning the power off and on again.
02
RAM disk mode is Off. Turn RAM disk mode On from the operation panel.
04
No disk space. Purge unnecessary files.
05
Specified file is not on disk.
06
Insufficient printer memory to support the RAM disk system. Expand printer
memory.

The following indicators light during normal operation and whenever the
printer needs attention. Depending on the status of lighting, each
indicator has the following meaning:
Indicator
Description
Flashing. Indicates an error that you can resolve. Refer to
Error Messages on page 6-5.
On. Indicates that the printer is ready. The printer prints the
data it receives.
Off. [Cancel] was pressed during Ready is displayed. Data
can be received but will not be printed. To resume printing,
press [Cancel] again.
Printing is cancelling.
Also, indicates when paper jam occurred, toner has run
out, cover is open, and so on.
Flashing. Indicates that a data is being received.
On. Indicates either that data received is being processed
before printing starts, or that data received is being written
to or read from a CompactFlash card, hard disk, RAM disk,
or USB flash memory.
Flashing. Indicates that the printer is ready to print when
Please wait is displayed. Also indicates that the
corresponding paper cassette is not installed. Indicates that
the printer requires maintenance such as adding paper,
cleaning the printer, replacement of maintenance kit,
preparing the toner container, formatting of hard disk and
CF card.
On. Indicates when paper jam occurred, toner has run out,
cover is open, and so on. If the message includes Press
GO, press [GO] to resume printing.
The ID or Password entered for the Security, Administrator,
or Job Accounting function is not correct. Check the ID or
Password, and enter the correct ID or password.
Troubleshooting
6-11
Clearing Paper Jams

If paper jams in the paper transport system, or no paper sheets are fed
at all, the Paper jam message appears and the location of the paper
jam (the component where the paper jam has occurred) is also
indicated. Status Monitor or COMMAND CENTER can indicate the
location of the paper jam (the component where the paper jam has
occurred). Remove the paper jam. After removing the paper jam, the
printer will resume printing.
Possible Paper Jam Locations

The figure below shows the printer's paper paths including the optional
paper feeder. The locations where paper jams might occur are also
shown here, with each location explained in the table below. Paper jams
can occur in more than one component on the paper paths.
Face-up Tray
FS-2020D/3920DN/4020DN:
PT-310
FS-6970DN: PT-430
Paper Feeder
FS-2020D/3920DN/
4020DN: PF-310
FS-6970DN: PF-430
FS-6970DN: PF-430
Paper jam message

Paper jam
MP Tray
Paper jam
EF
Paper jam
Bulk Feeder
6-12
Paper jam
location
A
Description
Reference page
Paper is jammed at the MP tray.

Depending on the installed options
additional error messages for
envelope feeder or bulk paper feeder
might appear [FS-3920DN and
FS-4020DN only]).
page 6-14
page 6-18
page 6-18
Troubleshooting
Paper jam message
Paper jam
location
Description
Reference page
Paper jam
Cassette 1 (to 4)
Paper is jammed at the paper

cassette. The cassette number can be
1 (topmost) to 5 (bottom) [FS-2020D: 1
and 2].
page 6-15
Paper jam
Duplexer
Paper is jammed inside the duplex

section.
page 6-16
Paper jam
Printer
Paper is jammed inside the printer.
page 6-17
Paper jam
Rear Unit
Paper is jammed inside the rear unit.
page 6-18
General Considerations for Clearing Jams

Bear in mind the following considerations when attempting paper jam
removal:
CAUTION When pulling the paper, pull it gently so as not

to tear it. Torn pieces of paper are difficult to remove and
may be easily overlooked, deterring the paper jam recovery.
If paper jams occur frequently, try using a different type of paper,

replace the paper with paper from another ream, or flip the paper
stack over. The printer may have problems if paper jams recur after
the paper is replaced.
Whether or not the jammed pages are reproduced normally after
printing is resumed, depends on the location of the paper jam.
Utilizing Online Help Messages

Online help messages are available in the printers message display to
provide simple instructions for clearing jams. Press ( ) when the paper
jam message has appeared. Then a help message will appear to
facilitate jam clearing in the location.
Troubleshooting
6-13
MP Tray
Paper is jammed at the MP tray. Remove the jammed paper using the
procedure given below.
6-14
Remove the paper jammed at the MP tray.
Open and close the top cover to clear the error.
Troubleshooting
Paper Cassette/Paper Feeder

1
2
Pull out the cassette or optional paper feeder.

Remove any partially fed paper.
Note Check to see if paper is loaded correctly. If not, reload
the paper.
Troubleshooting
Push the cassette back in securely. The printer warms up and

resumes printing.
6-15
Duplexer
Paper is jammed in the duplex section. Remove the jammed paper using
the procedure given below.
CAUTION Do not touch parts in this area, because it may

result in burn injury.
6-16
1
2
Pull the paper cassette all the way out of the printer.
Insert the paper cassette into the slot in the printer. The printer
warms up and resumes printing.
Open the duplexer's cover and remove any jammed paper.
Troubleshooting
Inside the Printer

1
2
Open the top cover and MP tray.
Open the feed cover.
Remove the paper from the printer
Lift the developer unit together with the toner container out of the
printer.
If the jammed paper appears to be pinched by rollers, pull it along

the normal running direction of the paper.
Note If you cannot find a paper jam, try checking inside the
rear of the printer. Refer to Rear Unit on page 6-18.
Troubleshooting
Insert the developer unit together with the toner container, back into
the machine.
Close the top cover and MP tray. The printer warms up and resumes
printing.
6-17
Rear Unit
1
If paper is not completely ejected into the output tray, open the rear
unit.
Open the fuser cover and remove the jammed paper by pulling it out.
Note If you cannot find a paper jam, try checking inside the
rear of the printer.
CAUTION The fuser unit inside the printer is hot. Do not

touch it with your hands as it may result in burn injury.
Remove jammed paper carefully.
Close the rear unit. The printer warms up and resumes printing out.
Envelope Feeder (FS3920DN/4020DN only)

Paper is jammed at the optional envelope feeder. Remove the jammed
paper using the same procedure as for a jam at the MP Tray. Then, open
and close the paper transfer unit. For details, refer to the User's Manual
for the envelope feeder.
Bulk Paper Feeder (FS3920DN/4020DN only)

Paper is jammed at the optional bulk paper feeder. Detach the bulk
paper feeder from the printer by sliding with the rail away from the
printer, holding the bulk paper feeder by both hands. If paper is partially
fed out from the feeder's output slot, pull the paper out by hand.
6-18
Troubleshooting
Using the Operation

Panel
This chapter contains explanations on the following topics:

General Information
Understanding the Operation Panel
Using the Menu Selection System
Report Print
USB Memory (USB flash memory selection)
Job Box
Counter (Viewing the counter value)
Paper Settings
Print Settings
Network (Network settings)
Device Common (Selecting/Setting the common device)
Security
Job Accounting (Job Accounting selection/setting)
Admin (Administrator settings)
Adjust/Maintenance (Adjust/Maintenance selection/setting)
7-2
7-3
7-8
7-11
7-17
7-19
7-25
7-26
7-35
7-50
7-55
7-67
7-75
7-81
7-83
7-1
General Information
This chapter provides the information you need to configure the Ecosys
printer. In general you need to use the operation panel only to make
default settings. You can make most changes to the printer settings
using the printer driver through the application software.
Note Changes to printer settings made using a software
application override changes made using the operation panel.
You can also access the printer's various settings from a remote
location, by using the control panel, the printer driver or other utilities
such as the Status Monitor Utility. Other printer utilities can be installed
using the CD-ROM supplied with the printer.
The chapter describes the operation panel in detail, including its menus
and the procedures for changing various printer settings.
7-2
Understanding the Operation Panel

The operation panel on the top of the printer has a 2-line by 16-character
liquid crystal display (LCD), eight keys, and three indicators (LED).
Indicators
Message Display
MENU Key
Cursor Key
OK Key
Cancel Key
GO Key
Messages that appear on the display and functions of indicators and

keys are explained in this chapter.
7-3
Message Display
The message display on the operation panel shows:
Status information, the ten messages listed below which are

displayed during normal operation.
Error codes, when the printer requires the operators attention; as
explained in the Operation Guide.
Status Information
Message
Meaning
Self test
The printer is performing self-diagnostics after power-up.
Please wait
The printer is warming up and is not ready.

When the printer is switched on for the first time, this message will take several minutes.
Please wait
(Adding toner)
Toner is currently being replenished. This message may be displayed during continuous
printing of a large volume of pages which require a large amount of toner such as with
photographs, etc.
Ready
The printer is ready to print.
Processing
The printer is receiving data to print. This is also shown when the printer is reading a CF
card, USB memory, hard disk, or RAM disk.
Sleeping
The printer is in Auto Sleep. The printer wakes from Auto Sleep whenever a print job is
received. The printer then warms up and goes on-line.
For details on Auto Sleep, refer to Sleep Timer (Sleep timer timeout time) on page 7-64.
Canceling data
Jobs inside the printer are being canceled. To cancel a job, refer to Canceling a Printing
Job on page 7-6.
Error Codes
Refer to the Troubleshooting section in the Operation Guide.
7-4
Indicators in Message Display
Ready

The following indicators light during normal operation and whenever the
printer needs attention. Depending on the status of lighting, each
indicator has the following meaning:
Indicator
Description
Flashing. Indicates an error that you can resolve. Refer to
Troubleshooting section in the Operation Guide.
On. Indicates that the printer is ready. The printer prints the
data it receives.
Off. [Cancel] was pressed during Ready is displayed.
Data can be received but will not be printed. To resume
printing, press [Cancel] again.
Printing is cancelling.
Also, indicates when paper jam occurred, toner has run
out, cover is open, and so on. For details, refer to the
Troubleshooting section in the Operation Guide.
Flashing. Indicates that a data is being received.
On. Indicates either that data received is being processed
before printing starts, or that data received is being written
to or read from a CompactFlash card, hard disk, RAM disk,
or USB flash memory.
Flashing. Indicates that the printer is ready to print when
Please wait is displayed. Also indicates that the
corresponding paper cassette is not installed.
Indicates that the printer requires maintenance such as
adding paper, cleaning the printer, replacement of
maintenance kit, preparing the toner container, formatting
of hard disk and CF card.
On. Indicates when paper jam occurred, toner has run out,
cover is open, and so on. If the message includes Press
GO, press [GO] to resume printing.
The ID or Password entered for the Security, Administrator,
or Job Accounting function is not correct. Check the ID or
Password, and enter the correct ID or password.
7-5
Keys
The operation panel keys are used to configure the printer operation.
Note that certain keys have a secondary function.
GO Key
Use this key to:
Recover from certain errors.

Recover from Auto Sleep mode.
Cancel Key
This key is used to:
Cancel a printing job.

Stop the alarm sound.
Reset numeric values or cancel a setting procedure while using
menu system.
Canceling a Printing Job
While the printer displays Processing, press [Cancel].

Print Cancel? appears on the message display followed by the
job name currently in progress.
Press U or V to display the desired job and [OK].

Canceling data appears on the message display and printing
stops after the current page is printed.
MENU Key
[MENU] lets you enter the menu system to change the setup and
printing environment of the printer.
Pressing this key during a menu selection will terminate the selection
and return the printer to the normal operation.
7-6
Cursor Keys
The four cursor keys are used in the menu system to access an item or
enter numeric values. Use U and V to change menus, and Y and Z to
move to the sub menu.
The cursor key with the question mark ( ) may be pressed when the
paper jam message has appeared on the message display. A help
message will then appear to facilitate jam clearing in the location.
When Use alternative? is shown in the message display, use the U
and V key to select the paper source.
OK Key
This key is used to:
Finalize settings of numeric values and other selections.

Set the paper source when Use alternative? is shown in the
message display.
7-7
Using the Menu Selection System

Menu Selection System
This section explains how to use the menu selection system. [MENU] on
the operation panel allows you to use the menu to configure the printer
settings to your specific needs. Settings can be made when Ready,
Please wait, Sleeping or Processing is indicated on the printer
message display.
Note Settings that are received from application software and the
printer driver will take priority over settings made in the operation
panel.
Entering the Mode Selection Menu

Press [MENU] when Ready, Please wait, Sleeping or
Processing is indicated on the printer message display.
The mode selection menu is displayed.
IMPORTANT Job Box is displayed in the selection menu when

the hard disk or RAM Disk is installed. For more information, refer
to Job Box on page 7-19 or RAM Disk Mode (Using the RAM
disk) on page 7-58.
7-8
Selecting a Menu
The mode selection menu is hierarchical. Press U or V to display the
desired menu.
Paper Settings >
If the selected menu has a sub-menu, > is displayed after the menu.
Press Z to move to the sub-menu or Y to go back.
Indicates that there is a sub-menu
>Type Adjust
CUSTOM 1
Indicates that this is
the sub-menu
>
> is displayed before the sub-menu.

Press Z to move to another sub-menu or Y to go back.
Indicates that there is

another sub-menu
>>Paper Weight
Normal 1
>> is displayed before the second sub-menu.
Indicates that this is the second sub-menu
Setting a Menu
Select the desired menu and press [OK] to set or change the
configuration.
Press U or V to display the desired item and [OK] to finalize the value
or selections set.
Cancelling Menu Selection

If you press [MENU] when a menu is selected, the message display
returns to Ready.
7-9
Setting a Mode Selection Menu

This section explains the setting procedures used for each menu item in
the mode selection menu.
Report Print
>
While the printer displays Ready, Please wait, Sleeping and

Processing, press [MENU]. The mode selection menu is
displayed. (For example : Report Print)
Each time you press U or V, the selection changes.
Report Print
USB Memory
Job Box
Counter
Paper Settings
Print Settings
Network
Device Common
Security
Job Accounting
Admin
Adjust/Maintenance
Note If you use the mode first selected when the printer is turned
on, Report Print is displayed. For the second and subsequent
times, the last menu option you selected the previous time is
displayed.
7-10
Report Print
The printer prints the report. Report Print includes the following items:
Report Print
>
Print Menu Map

Print Status Page
Print Fonts List
Print Hard Disk File List
Print RAM Disk File List
Print Mem. Card File List
1
2
Press [MENU].
Press U or V repeatedly until Report Print > appears.
Note that menus shown in the list may vary depending on which optional
units installed in the printer.
Print Menu Map

The printer prints a full list of the menu selection system menu map.
>Print
Menu Map ?
1
2
Press Z while Report Print > is displayed.
Press [OK]. The message Processing appears and the printer

prints a Menu Map.
>Print Menu Map appears. In other displays, press U or V

repeatedly until the map appears.
7-11
Menu Map Sample
Menu Map
Printer
Firmware version
7-12
Print Status Page

You can check the printer's current status, including available memory
space and option settings by printing a status page.
>Print
Status Page ?
1
2
3
4

Press U or V repeatedly until >Print Status Page appears.
Press [OK] again. The message Processing appears and the
printer prints a status page.
For a sample status page and its full description, refer to the next section
Understanding the Status Page.
Understanding the Status Page

The numbers in the following diagram refer the items explained below
the diagram. The items and values on the status page may vary
depending on the printers firmware version.
Status Page
Printer
Firmware version
Paper Settings
Group Settings
Interface Block
Memory
Print Settings
Device Common Settings

Emulation
Option Status
7
Counters
Network
Toner Gauge
7-13
Firmware Version
This item shows the version and release date of the printer firmware.
Printer Settings Information

This item shows various printer settings for hardware-related items:
MP tray paper size and type

Paper cassette size and type
Sleep time
Formfeed timeout time
Installed Options
This item shows the options installed in the printer:
Hard disk
Memory card (CompactFlash card)
Network Status
This item shows the IP address, subnet mask address, and default
gateway address for the network interface card in the printer.
Interface Information
This information shows the settings for all interfaces installed in the
printer.
Memory
This item shows:
Standard memory in the printer

Option memory slot status in megabytes
Total memory in the printer
Current status of the RAM disk
Emulation
This item shows all available emulations of the printer. The PCL 6
emulation is set as default when the printer is shipped from the
factory. The emulations are:
PCL 6
KPDL
Line Printer
IBM Proprinter
DIABLO 630
EPSON LQ-850
KC-GL (FS-6970DN only)
Page Information
This item shows the page related items:
Total printed page count

Total page count of each paper size
Consumable Status
This item shows the approximate level of remaining toner. When the
value is 100, the toner container is full. The closer to 0, the smaller
the amount of remaining toner.
7-14
Print Fonts List

To help you decide in selecting a font, you can printout lists of the
internal fonts or the optional fonts.
>Print
Fonts List ?
1
2
3

printer prints a list of fonts with a sample and font ID (number) for
each of them.
Press U or V repeatedly until >Print Fonts List appears.

Print Hard Disk File List

This allows you to print a list of the files on the hard disk.
This menu is displayed only when the optional hard disk is installed on
the printer.
IMPORTANT This is only displayed when the printer has a hard disk
installed and the disk is correctly formatted.
1
2
>Print Hard Disk
File List ?

Press U or V repeatedly until >Print Hard Disk File List
appears.

printer prints a list of files stored in a hard disk.
Print RAM Disk File List

This allows you to print a list of the files on the RAM disk.
IMPORTANT This is displayed when RAM disk mode is enabled.
1
2
>Print RAM Disk
File List ?

Press U or V repeatedly until >Print RAM Disk File List
appears.

printer prints a list of files stored in a RAM disk.
7-15
Print Mem. Card File List

This allows you to print a list of the files on a CompactFlash (memory)
card.
IMPORTANT This message will be displayed only when the

CompactFlash card is installed in the printer and properly
formatted.
1
2
>Print Mem. Card
File List ?
7-16

Press U or V repeatedly until >Print Mem. Card File List
appears.

printer prints a list of files stored in a CompactFlash card.
USB Memory (USB flash memory selection)

This specifies the settings for removing the USB flash memory and
printing USB flash memory content.
IMPORTANT This message is displayed only when the USB host

block is set to Unblock. For more information, refer toI/F Block
(Interface (external device) block setting) on page 7-68.
The options available in USB flash memory are as follows:
USB Memory
>
Print File (Printing a file)

Copies (Number of copies)
Paper Source (Selecting the paper feed source)
Remove Device (Removing the USB flash memory)
Print File List (Printing a list of the files on a USB flash memory)
1
2
Press [MENU].
Press U or V repeatedly until USB Memory > appears.
Note that menus shown in the list may vary depending on which
optional units installed in the printer.
Print File (Printing a file)

You can use this to specify printing for files in the USB flash memory.
1
2
3
4
/
/00:Folder 1
Press Z while USB Memory > is displayed.

>Print File appears. In other displays, press U or V repeatedly
until the map appears.
Press [OK] again. The folder or file appears.
(For example : Folder 1)
Each time you press U or V, the next folder or file appears in
succession.
To view lower-level folders or files, press Z.
(For example : Folder 2)
/00:Folder 1
/01:Folder 2
To view folders or files on still lower levels, press Z.

(For example : File 3)
/.../01:Folder 2
02:File 3
IMPORTANT The Print File menu option is only displayed

when there is a PDF, XPS or TIFF file in the USB memory. Note
also that up to 3 levels of folders or files are displayed. It might
take some time before the folder or file name appears, depending
on the size of the USB flash memory or the number of files.
You can move between the folder levels by pressing U and V or Y
and Z.
/.../01:Folder 2
?
02:File 3
Copies

(For example : File 3)
Press [OK] again. Copies appears.
001
7-17

Sets the number of copies printed of the specified file in USB flash
memory.
IMPORTANT To use this feature, an optional hard disk must be

installed in the printer or the RAM disk must be set to On.
Copies
While Copies in step 5 above is displayed, press U and V or Y

and Z to display the number of copies. (E.g.: 10)
Press [OK]. Paper Source and a question mark (?) appears.
010
Paper Source
? Cassette 1

Sets the paper used for printing the specified file in USB flash memory.
Paper Source
? Cassette 2
While Paper Source in step 2 above is displayed, press U and V

or Y and Z repeatedly until the paper source appears.
(For example : Cassette 2)
Note that menus shown in the list may vary depending on which
optional units installed in the printer.
Press [OK]. The message Processing appears and the printer

prints a file stored in a USB memory.
Remove Device (Removing the USB flash memory)

Specifies the setting for USB flash memory removal.
>Remove Device ?
1
2
3
Press [OK] again. Menu display ends and the USB flash memory
device can be removed.
Press U or V repeatedly until >Remove Device appears.

Print File List (Printing a list of the files on a USB

flash memory)
This allows you to print a list of the files on a USB flash memory device.
>Print
File List ?
7-18
1
2
3

printer prints a list of files stored in a USB flash memory.
Press U or V repeatedly until >Print File List appears.

Job Box
Job box implements the Job Retention function and Job Storage function
that are available from the printer driver. The settings are specified from
the printer driver. Refer to KX Printer Driver User Guide for the driver
settings.
In either job mode, when printing a document, the print data is
transferred from the computer to the printer then stored on the printers
hard disk. Since copies of the document are printed using the stored
data, printing is performed faster with less computer spooling time and
less network traffic.
IMPORTANT To use the Job Box, an optional hard disk must be

installed in the printer.
The RAM disk may also be used in the Proof-and-Hold and Private
Print modes.
Job Retention
Job Retention has four modes as summarized below. These modes are
selected from the printer driver through the application software:
Quick Copy
Proof-and-Hold
Private Print
Stored Job
Primary function
To later print
additional copies
To proof the first copy

before printing
multiple copies
To hold the document

in printer to prevent
unauthorized access
To electronically store
documents such as
fax cover pages
Start storing by
Printer driver
Printer driver
Printer driver
Printer driver
On terminating print
setting from
application software
Prints simultaneously
Prints one copy

simultaneously
Does not print
Does not print
Retrieved by
Operation panel
Operation panel
Operation panel
Operation panel
Default number of
copies printed at
retrieval
Same as storing
(can be changed)
One less
(can be changed)
Same as storing
(can be changed)
One
(can be changed)
Maximum number of
jobs stored *
32, expandable to 50
32, expandable to 50
Depends on the hard

disk capacity
Depends on the hard

disk capacity
PIN security
No
No
Yes
Yes (if necessary)
Data after printing
Stored
Stored
Deleted
Stored
Data at power off
Deleted
Deleted
Deleted
Stored
Hard disk
Necessary
Unnecessary
(RAM disk may also
be used)
Unnecessary
(RAM disk may also
be used)
Necessary
*.
Jobs in excess will cause the earlier ones to be deleted.
7-19
Job Storage
Job storage stores print jobs either temporarily or permanently, as you
click an appropriate radio button on the printer driver when printing from
a computer.
There are two types of code job:
Permanent (permanently saved) code jobs
Temporary (temporarily saved) code jobs
If there is insufficient space on the hard disk, existing temporary code jobs
are deleted, starting from the oldest files. Permanent jobs are not
automatically deleted in this way. To print, select the printer driver.
Note Refer to the KX Printer Driver User Guide for the driver
settings and print (save) procedures.
The options available in Job Box are as follows:
Using Quick Copy/Proof-and-Hold
Quick Copy (User Name) (Selecting the User)
(User Name) (Data Name) (Selecting the data)
(Data Name) Copies (number of copies) (Number of copies / deleted)
Printing a Private Print/Stored Job
Private/Stored (User Name) (Selecting the User)
(User Name) (Data Name) (Selecting the data)
(Data Name) ID (number of copies) (Input passwords)
(Data Name) Copies (number of copies) (Number of copies / deleted)
Job Box Configuration (Job Box Configuration)
Job Box
>
1
2
Press [MENU].
Press U or V repeatedly until Job Box > appears.
Note that menus shown in the list may vary depending on which optional
units installed in the printer.
Quick Copy (Using Quick Copy)

This mode enables you to print the requested number of copies of a job,
simultaneously storing the job on the hard disk/RAM disk. When
additional copies are required, you can reprint the required number of
copies from the printer operation panel. To print a job as a quick copy job,
refer to KX Printer Driver User Guide.
The default number of print jobs that can be stored on the hard disk is 32.
This value can be increased to up to 50 from the Job Box Configuration
menu. For details, refer to Changing the Maximum Number of Quick Copy
on page 7-24. When the number of jobs reaches the limit, the oldest job
will be overwritten by the new one.
When the printer is turned off, all stored jobs will be deleted.
settings.
7-20
Printing Additional Copies using Quick Copy
1
2
>Quick Copy
?Harold
>Quick Copy
?Arlen
>Arlen
?Report
>Report
Copies
Press Z while Job Box > is displayed.

Press U or V repeatedly until >Quick Copy appears. The name
entered in the printer driver (Harold, in this example) also appears.
Press [OK]. A blinking question mark (?) appears before the user
name.
Press U or V to display the desired user name, Arlen, in this

example.
Press [OK]. The job name entered in the printer driver (Report, in
this example) appear with a blinking question mark (?) before the
letters.
6
7
Press U or V to scroll to the desired job title.
Press [OK] to finalize the copy count. The printer prints the specified
number of copies for the job.
001
Press [OK]. The number of copies to be printed can be set. To

increase the copy count, press U; to decrease the copy count, press
V.
Deleting a Quick Copy Job
>Report
Copies
>Report
Delete
Follow steps 1 through 6 in the above section to let the title of the job
to be deleted displayed.
When the title of the job to be deleted is displayed, e.g. Report,

press [OK]. The cursor (_) below the copy count starts to blink.
Press V repeatedly until Delete appears below the title.
Press [OK]. The message Processing appears and the stored

quick copy job is deleted.
001
Using Proof-and-Hold
When you print multiple copies, this mode first prints one copy so that
you can proof it before continuing to print the remaining copies. Since
you can proof the printouts before printing the remaining copies,
wastage of paper can be reduced.
The printer prints one copy and, at the same time, saves the print job on
the hard disk/RAM disk. You can also change the number of copies
when resuming printing from the operation panel.
When the printer is turned off, all stored jobs will be deleted.
settings.
7-21
Printing Remaining Copies of a Proof-and-Hold Job
1
2
>Quick Copy
?Harold
>Quick Copy
?Arlen
>Arlen
?Report
>Report
Copies

Press U or V repeatedly until >Quick Copy appears. The name
entered in the printer driver (Harold, in this example) also appears.
name.
Press U or V to display the desired user name, Arlen, in this

example.
Press [OK]. The job name entered in the printer driver (Report, in
this example) appear with a blinking question mark (?) before the
letters.
6
7
Press U or V to scroll to the desired job title.
001
Press [OK]. The number of copies to be printed can be set. To

increase the copy count, press U; to decrease the copy count, press
V.
Deleting a Proof-and-Hold Job
>Report
Copies
>Report
Delete
7-22
Follow steps 1 through 6 in the above section to let the title of the job
to be deleted displayed.
When the title of the job to be deleted is displayed, e.g. Report,

press [OK]. The cursor (_) below the copy count starts to blink.
Press V repeatedly until Delete appears below the title.
Press [OK]. The message Processing appears and the stored job
is deleted.
001
Private/Stored (Printing a Private Print/Stored Job)

In private printing, you can specify that a job is not printed until you
release the job from the operation panel. When sending the job from the
application software, specify a 4-digit access code in the printer driver.
The job is released for printing by entering the access code on the
operation panel ensuring confidentiality of the print job.
In the stored job mode, access codes are not mandatory, but can be set
on the printer driver if printing with PIN security is required. Then, the
access code must be entered on the operation panel to print a stored
job. Print data will be stored in the hard disk/RAM disk after printing.
Refer to KX Printer Driver User Guide for the driver settings.
Releasing a Private/Stored Job
1
2
>Private/Stored
?Harold
>Arlen
?Agenda
>Agenda
ID

Press U or V repeatedly until >Private/Stored appears. The
name entered in the printer driver (Harold, in this example) also
appears.
name.
Press U or V to display the desired user name (Arlen, in this

example).
Press [OK]. The user name and the job name (Agenda, in this
example) entered in the printer driver appear with a blinking question
mark (?).
6
7
Press U or V to display the desired job title.
0000
Press [OK]. The ID input line appears. Enter the four-digit access
code entered in the printer driver and press [OK].
To enter the ID, press Y or Z to move the cursor to the number to be
changed and then enter the correct number by pressing U or V.
Note If you entered the wrong ID, ID error appears. Check the
ID or Password, and enter the correct ID.
>Agenda
Copies
You can set the number of copies to be printed. To increase the copy
count, press U; to decrease the copy count, press V.
001
7-23
Deleting a Private/Stored Job

You can individually delete stored jobs by performing the following
procedure. Jobs saved using Private Print will be automatically deleted if
you turn the power off after printing, but jobs saved using Stored Job will
not be deleted automatically.
>Agenda
Copies
1
2
Follow steps 1 through 6 in the above section.
Press V repeatedly until Delete appears for the number of copies.
Press [OK]. The private job is deleted.
001
>Agenda
Delete
When the title of the job to be printed is displayed (Agenda, in this

example), press [OK]. Enter the four-digit access code entered in
the printer driver and press [OK].
Job Box Configuration

This allows you to change the number of print jobs that can be stored on
the hard disk and disk capacity allocated to each function.
Changing the Maximum Number of Quick Copy

This changes maximum number of Quick Copy from 0 to 50. The default
is 32.
>Job Box
>
Configuration
>>Quick Copy
1
2
3
4
Press Z.
Press [OK]. A blinking cursor (_) appears.
Press U or V to increase or decrease the value at the blinking

cursor. The value can be set between 0 and 50. Use Y and Z to
move the cursor right and left.
7
8
When the desired maximum number of jobs is set, press [OK].
Press U or V repeatedly until >Job Box Configuration >

appears.
Press U or V repeatedly until >>Quick Copy appears.
32
>>Quick Copy
32
7-24
Counter (Viewing the counter value)

This only displays the total number of pages printed. You cannot change
the displayed number.
Counter
>
>Printed Pages
0002000
1
2
Press [MENU].
Press Z. >Printed Pages appears as he total number of pages

printed. (E.g.: 2000)
Press U or V repeatedly until Counter > appears.
7-25
Paper Settings
This sets the paper size and type for the MP tray and cassettes from
which paper is supplied.
The options available in Paper Settings are as follows:
Paper Settings >
7-26
MP Tray Size (Setting MP tray paper size)

MP Tray Type (Setting the MP tray paper type)
Cassette (1 to 4) Size (Setting the cassette paper size)
Cassette (1 to 4) Type (Setting the cassette paper type)
Type Adjust (Creating custom paper type)
Reset Type Adjust (Resetting the custom paper type)
1
2
Press [MENU].
Press U or V repeatedly until Paper Settings > appears.
MP Tray Size (Setting MP tray paper size)

When you use the MP tray, you should set the MP tray size to the paper
size that is used to format the job to print. If the sizes do not match,
printing will not be performed on the correct size paper.
The default setting is Letter size for the U.S. and Canada and A4 for
other countries. For more information about the paper sizes that you can
feed from the MP tray, refer to Paper Specifications on page 2-2.
Note Feeding the paper having a paper size which does not
match the current paper size from the MP tray can cause paper
jam.
>MP Tray Size

? A4
1
2
3
Press Z while Paper Settings > is displayed.
Press U or V to display the desired paper size. The message

display toggles through the following paper sizes:
5
6
Press U or V repeatedly until >MP Tray Size appears.

For FS-2020D/3920DN/4020DN
For FS-6970DN
Env. Monarch
Envelope #10
Envelope #9
Envelope #6
Envelope DL
Envelope C5
A6
B6
A5
B5
ISO B5
A4
Executive
Letter
Legal
Custom
Oficio II
Statement
Folio
Youkei 2
Youkei 4
16K
Hagaki
OufukuHagaki
Env. Monarch
Envelope #10
Envelope #9
Envelope #6
Envelope DL
Envelope C5
A6
B6
A5-R
B5
ISO B5
A4-R
A4
Executive
Letter-R
Letter
Legal
A3
B4
Ledger
Custom
Envelope C4
Oficio II
Statement
Folio
Youkei 2
Youkei 4
8K
16K
Hagaki
OufukuHagaki
Press [OK].
7-27
MP Tray Type (Setting the MP tray paper type)

You can use this to set the paper type that can be supplied from the MP
tray. The default setting is PLAIN.
For more information about paper types that you can feed from the MP
tray, refer to Paper Specifications on page 2-2.
>MP Tray Type

? PLAIN
1
2
3
Press U or V to display the desired paper type. The message

display toggles through the following paper types:
Press U or V repeatedly until >MP Tray Type appears.

PLAIN
TRANSPARENCY
PREPRINTED
LABELS
BOND
RECYCLED
VELLUM
ROUGH
LETTERHEAD
COLOR
PREPUNCHED
ENVELOPE
CARDSTOCK
THICK
HIGH QUALITY
CUSTOM 1 (to 8)
Note You can define any paper type and store that definition
in the printer. For more information, refer to Type Adjust
5
6
7-28
Press [OK].
Cassette (1 to 5) Size (Setting the cassette paper size)

To set the standard sizes A5, A4, B5, A3 (FS-6970DN only), Letter, and
Legal size for the paper cassette, load the paper and turn the paper size
dial so that the size of the paper you are going to use appears in the
paper size window. To load a non-standard paper size (sizes other than
A5, A4, B5, A3 (FS-6970DN only) and Letter) into a paper cassette, refer
to the custom paper sizes listed on page 7-30.
If the PF-310 optional paper feeder is installed, use the same procedure
to load paper into the paper feeder cassettes.
Pull the cassette out of the printer and set the paper size using the
paper size dial.
Adjust the position of the width guides located on the left and right
sides of the cassette. Press the release button on the left guide and
slide the guides to the paper size required, and load the paper into
the cassette.
7-29
Custom Paper Size

If you use a non-standard size paper, load the paper and select the
paper size dial to OTHER (refer to the Loading Paper section in the
Operation Guide).
Setting the Paper Size from the Operation Panel

Use the operation panel to set the size of paper loaded in the cassette
on the printer. This menu appears if the size dial for the cassette is set to
Other.
1
2

Press U or V repeatedly until >Cassette Size > appears.
If optional paper feeders are added, Cassette1 Size will appear
for the standard paper cassette and Cassette2 Size, Cassette3
Size (FS-3920DN/FS-4020DN/FS-6970DN), Cassette4 Size
(FS-3920DN/FS-4020DN//FS-6970DN) and Cassette5 Size (FS6970DN) will appear for the optional paper feeders.
>Cassette Size >

? Custom
Press U or V to display the desired paper size. The message

display toggles through the following paper sizes:
For FS-2020D/3920DN/4020DN
For FS-6970DN
Envelope C5
A6 (FS-3920DN/FS-4020DN only)
A5
B5
ISO B5
A4
Executive
Letter
Legal
Custom
Oficio II
Folio
16K
Envelope C5
A5-R
A5 (Cassette 1 only)
B5
ISO B5
A4-R
A4
Executive
Letter-R
Letter
Legal
A3
B4
Ledger
Custom
Enfvelope C4
Oficio II
Folio
16K
When the desired paper size is displayed, press [OK]. The paper
size is set for the paper cassette.
If you selected Custom in step 4, be sure to set the unit of
measurement and the dimensions of the paper as described in the
following sections.
Select the units of measurement as described in the next section.
7-30
Unit (Selecting the unit of measurement)
1
2
>>Unit
? mm
Press Z.
Press U or V repeatedly until >>Unit appears. The unit of
measurement can be selected between millimeters and inches. The
current unit of measurement is displayed (the default setting is mm).
4
5
Select mm or inch using U or V.

Press [OK].
Set the dimensions of the paper as described in the next section.
Entering the Width and Length

Enter the paper size for X Dimension and Y Dimension as shown in
the figure.
For FS-2020D/3920DN/4020DN
>>X Dimension
216 mm
X Dimension
148 to 297mm
(5-13/16 to 11-3/4 inches)
210 to 432mm
(8-1/4 to 17 inches)
X Dimension
140 to 216mm
(5-1/2 to 8-1/2 inches)
Y Dimension
Y Dimension
210 to 356mm
(8-1/4 to 14 inches)
For FS-6970DN
When the unit of measurement is set, press V.

>>X Dimension appears (the paper width setting).
Press U or V to increase or decrease the value of the figure where

the cursor is blinking and display the desired width.
Acceptable paper widths are 140 to 216 mm (5-1/2 to 8-1/2 inches).
4
5
Display the paper width and press [OK].
6
7
Display the paper length, press [OK].
When the width is set, press V. >>Y Dimension appears (the

paper length setting). Set the desired length in the same way as the
width.
Acceptable paper lengths are:
For FS-2020D/3920DN/4020DN: 210 to 356 mm (8-1/4 to 14
inches).
For FS-6970DN: 210 to 432 mm (8-1/4 to 17 inches).
7-31
Cassette (1 to 5) Type (Setting the cassette paper

type)
By setting a paper type (plain, recycled, etc.) for the paper cassette, you
can automatically select the paper in the paper cassette according to the
paper type you command on the printer driver. The default setting is
plain paper for all paper cassettes.
If the PF-310 optional paper feeder is installed, use the same procedure
to setting the cassette paper type.
For more information about paper types that you can feed from the paper
cassette, refer to Paper Specifications on page 2-2.
1
2

Press U or V repeatedly until >Cassette Type appears.
If optional paper feeders are added, Cassette 1 Type will appear
for the standard paper cassette and Cassette 2 Type, Cassette
3 Type (FS-3920DN/FS-4020DN/FS-6970DN), Cassette 4
Type (FS-3920DN/FS-4020DN/FS-6970DN) and Cassette 5
Type (FS-6970DN) will appear for the optionalpaper feeders.
>Cassette Type
? PLAIN
To change paper type, press [OK]. A blinking question mark (?)

appears.
Press U or V to display the desired paper type. The message

display toggles through the following paper types:
PLAIN
PREPRINTED
BOND
RECYCLED
ROUGH
LETTERHEAD
COLOR
PREPUNCHED
HIGH QUALITY
CUSTOM 1 (to 8)
Note You can define any paper type and store that definition
in the printer. For more information, refer to Type Adjust
5
6
7-32
Press [OK].
Type Adjust (Creating custom paper type)

The following describes the procedure used to set a user-defined paper
type for the printer. Eight custom user settings may be registered. After
having been set, any of these may be called up when setting the paper
type for a paper source.
The paper weight and duplex path can be set (refer to Paper Weight
(Setting the paper weight) on page 7-33, and Duplex Path (Setting the
duplex path) on page 7-34) after selecting the paper type to be
customized as follows. For how to reset the customized settings, refer to
Reset Type Adjust (Resetting the custom paper type) on page 7-34.
>Type Adjust
?PLAIN
>
1
2
3
Press U or V to display the desired paper type. The display

changes as shown below.
Press U or V repeatedly until >Type Adjust > appears.

PLAIN
TRANSPARENCY
PREPRINTED
LABELS
BOND
RECYCLED
VELLUM
ROUGH
LETTERHEAD
COLOR
PREPUNCHED
ENVELOPE
CARDSTOCK
THICK
HIGH QUALITY
CUSTOM 1 (to 8)
5
6
Press [OK].
Press Z and proceed to the next step Paper Weight (Setting the
paper weight).
Paper Weight (Setting the paper weight)

You can set the paper thickness for your custom paper type to be
customized. The default setting is Normal 2.
>>Paper Weight
? Normal 2
Display the custom paper type (refer to Type Adjust (Creating

custom paper type) on page 7-33) and press Z.
2
3
Press U or V repeatedly until >>Paper Weight appears.

7-33
Press U or V to display the desired paper thickness. The display

changes as shown below. For details of the default setting for each
paper type, refer to Paper Type on page 2-12.
Light
Normal 1
Normal 2
Normal 3
Heavy 1
Heavy 2
Heavy 3
Extra Heavy
5
6
Press [OK].
Duplex Path (Setting the duplex path)
>>Duplex Path
? Enable
Display the custom paper type (refer to Type Adjust (Creating

custom paper type) on page 7-33) and press Z.
2
3
Press U or V repeatedly until >>Duplex Path appears.
Select Enable or Disable using U or V. For details of the default

setting for each paper type, refer to Paper Specifications on page 22.
5
6
Press [OK].
The custom paper type setting is completed.
Reset Type Adjust (Resetting the custom paper type)

Reset all the custom paper type that was set in Type Adjust (Creating
custom paper type) on page 7-33.
>Reset Type
Adjust ?
7-34
1
2
3
Press [OK] again. All customized paper types will be reset to the
default. The display returns to Ready.
Press U or V repeatedly until >Reset Type Adjust appears.

Print Settings
These settings specify printing parameters such as the print quality used
for printing (Normal or Fine), the gloss mode (Low or High), the number
of copies, reduced printing and the page orientation.
The options available in Print Quality are as follows:
Print Settings >

Paper Feed Mode (Setting the paper feed source)
Duplex (Duplex Printing)
Paper Output (Selecting the output stack)
Override A4/LT (Overriding difference between A4 and Letter)
Emulation (Setting the emulation)
Font Select (Selecting the default font)
Code Set (Setting the code set)
Print Quality (Setting print quality)
Page Set (Setting pagination)
1
2
Press [MENU].
Press U or V repeatedly until Print Settings > appears.

You can select the paper source, from which the printer feeds paper as
the default. If an optional paper feeder(s) is installed, it is also available
for the default paper source.
>Paper Source
? Cassette 1
1
2
3
Press Z while Print Settings > is displayed.
Press U or V to display the desired paper feed source. The

message display toggles through the following paper feed sources,
depending on the installed optional paper feeders (from the top most
paper cassette to the bottom paper cassette):
Press U or V repeatedly until >Paper Source appears.

To change the current paper feed source, press [OK]. A blinking
question mark (?) appears.
MP tray
Cassette 1
Cassette 2
Cassette 3 (FS-3920DN/FS-4020DN/FS-6970DN only)
Cassette 4 (FS-3920DN/FS-4020DN/FS-6970DN only)
EF (FS-3920DN/FS-4020DN only)
Bulk feeder (FS-3920DN/FS-4020DN only)
Cassettes 2, 3, 4 and 5 are available for selection when the
optional paper feeders are installed.
5
6
Press [OK].
7-35
Paper Feed Mode (Setting the paper feed source)

This mode specifies how the paper should be fed once the paper feed
source and paper type have been chosen. If Auto is selected, the printer
searches for a paper feed source that matches the paper size and type,
and paper is then delivered from that source. If Fixed is selected and
there is no matching paper feed source, handling proceeds as specified
by Paper Mismatch for Error Handling. For details on paper
feeding when Fixed is selected, refer to Paper Mismatch (Detection
settings for paper size/type errors when the paper source is fixed) on
page 7-62. The default setting is Auto. To change the settings, follow
the steps described below.
>Paper Feed Mode

? Auto
1
2
3
4
5
6
Press U or V until Auto or Fixed appears.
Press U or V repeatedly until >Paper Feed Mode appears.

Press [OK].
When the Paper Runs Out During Printing

When Paper Feed Mode is set to Fixed, if the paper in the cassette
runs out during printing, Load Cassette 1 is displayed and the printer
stands by. In this event, either replenish the paper in the empty cassette
or use the procedure below to print from another paper source.
While Load Cassette 1 is displayed, press U or V repeatedly

until Use alternative? appears.
Press U or V repeatedly until the desired paper source and size

appears.
Each time you press U or V, another paper cassette or the paper
size that can currently be fed from the MP tray appears.
7-36
Press [OK]. Printing continues.
Duplex (Duplex printing)

Using the duplexer, you can automatically print on both sides of the
paper. The duplexer is mounted underneath the printer.
Duplex printing is available for the following paper types:
PLAIN
PREPRINTED
BOND
RECYCLED
ROUGH
LETTERHEAD
COLOR
PREPUNCHED
HIGH QUALITY
CUSTOM 1 (to 8)
Activating the duplexer is done by selecting either short edge or long
edge binding mode.
Note Duplex printing can be also performed from the MP tray. If
the paper to be fed from the MP tray does not match the paper size
and paper type of the current paper feed source cassette, a paper
jam may occur.
Binding Modes
Binding refers to the manner in which printed pages of paper are joined
together (by gluing, stitching, etc.) in book form. The two possible types
of binding are: long-edge binding, in which pages are joined together
along their long edge; and short-edge binding, in which they are joined
together along their short edge. In selecting a binding type, you must
also consider the orientation of the printed page. You can use long-edge
or short-edge binding with either landscape or portrait printing.
Depending on the binding type and print orientation, the duplexer
provides four types of binding. These are: (1) portrait, long-edge, (2)
portrait, short edge, (3) landscape, long-edge, and (4) landscape, shortedge. The figure below shows these binding methods.
(1)
(2)
Portrait,
long-edge
Portrait,
short-edge
Landscape,
short-edge
(3)
Landscape,
long-edge
>Duplex
? Off
1
2
3
(4)

Press U or V repeatedly until >Duplex appears.
7-37
Press U or V to display the desired binding mode. The message

display toggles through the following:
Off (default)
Short edge bind
Long edge bind
5
6
Press [OK].
Paper Output (Selecting the output stack)

The Paper Output menu on the operation panel allows you to select
either the face-down tray or the faceup tray option for the output stack.
Note This menu can be used for FS-3920DN and FS-4020DN.
>Paper Output
Top tray FaceDn
>Paper Output
?Top tray FaceDn
1
2
To change the output stack, press [OK]. A blinking question mark (?)
appears.
Press U or V to select output stack - Top tray FaceDn or

RearTray FaceUp.
5
6
When the desired output stack is displayed, press [OK].
Press U or V repeatedly until >Paper Output appears.
Override A4/LT (Overriding difference between A4

and Letter)
When the Override A4/LT is turned On using the operation panel, the
printer ignores the difference between A4 and Letter paper sizes.
Printing is performed without an error message even if the actual paper
size in the current cassette differs from the paper size formatting the job.
By default, this feature is On.
>Override A4/LT
? On
1
2
3
4
5
6
Press U or V repeatedly until >Override A4/LT appears.

Press [OK].
Emulation (Setting the emulation)

You can change the emulation mode. Use the procedure below to select
the mode.
1
7-38
>Emulation
? PCL 6
Press U or V repeatedly until >Emulation > appears on the

message display. One of the emulation modes appears, indicating
the emulation currently in use.
Press U or V repeatedly until the desired emulation mode is

displayed.
PCL 6
KC-GL (FS-6970DN only)
KPDL
KPDL (AUTO)(default)
Line Printer
IBM Proprinter
DIABLO 630
EPSON LQ-850
5
6
Press [OK].
Alternative Emulation for KPDL Emulation

KPDL is Kyoceras implementation of the PostScript language. The
KPDL (AUTO) emulation enables the printer to automatically change the
emulation mode according to the data received when printing.
In addition to KPDL (AUTO) emulation, you can use the operation panel
to set another emulation mode that is used very often. The default
setting is PCL 6.
1
2
>Emulation
? PCL 6
>Emulation
? KPDL (AUTO)
Press [MENU].
Press U or V repeatedly until >Emulation > appears on the
message display.
Press U or V repeatedly until KPDL (AUTO) appears.
5
6
Press [OK].
7
8
Press Z. When >>Alt. Emulation is displayed, press U or V.

The names of alternative emulations appear - PCL 6, Line
Printer, IBM Proprinter, DIABLO 630, KC-GL (FS-6970DN
only) or EPSON LQ-850.
Press U or V repeatedly until the desired alternative emulation
appears.
9 Press [OK].
10 Press [MENU]. The display returns to Ready.
7-39
Error Report (Printing KPDL errors)

The printer can print error descriptions when printing error occurs during
KPDL emulation. The default is On the printer prints KPDL errors.
>Emulation
? PCL 6
>Emulation
>
? KPDL (AUTO)
>>Error Report
? On
1
2
3
Select KPDL or KPDL (AUTO) using U or V. Press [OK].
5
6
7
Press Z. >>Error Report appears.
Press U or V repeatedly until >Emulation > appears.


Select On or Off using U or V. Press [OK].
Selecting KC-GL Pen Width (FS-6970DN only)

The KC-GL emulation mode enables you to set the pen widths in dots,
for pen numbers 1 to 8.
>Emulation
? PCL 6
>Emulation
KC-GL
>
>>Pen(1) Width
?
01 dot(s)
1
2
3
Select KC-GL using U or V.
Press Z. >>Pen(1) Width appears. Press U or V repeatedly

until the desired pen number of 1 to 8 is displayed.
Press [OK]. A blinking question mark (?) appears at the last digit.

cursor. Use Y and Z to move the cursor right and left.
Press [OK].
Press U or V repeatedly until >Emulation > appears.

Procced to next subsection to select the KC-GL page size.
Selecting KC-GL Page Set

The KC-GL emulation mode also enables you to set the KC-GL page
size.
1
2
7-40
Press Y while >>Pen(X) Width is displayed.

Press U or V repeatedly until >>KC-GL Page Set appears.
>>KC-GL Page Set

? [SPSZ]
Press U or V repeatedly until the desired page size (A2, A1, A0, B3,
B2, B1, B0, and SPSZ) is displayed. When selecting SPSZ, printing
will be done with the paper size specified by the PRESCRIBE SPSZ
command.
5
6
Press [OK].
Font Select (Selecting the default font)

You can select the default font. The default font can be one of the
internal fonts or a font that is downloaded to the printer memory or stored
on CompactFlash card, or hard disk.
In this menu, you can also set the type and pitch for Courier and Letter
Gothic; as well as to print a font list.
>Font Select
Internal
>
>> I000
1
2
To select an internal font, make sure that Internal is displayed

and press Z. The display changes. If Internal is not displayed, press
[OK], then press U or V until it appears.
Press U or V repeatedly until >Font Select > appears.
To select an optional font, press [OK] while >Font Select > is

displayed. Press U or V repeatedly until Option appears and then
press [OK]. Press Z next to display the font selection shown above.
You can perform this operation only when optional fonts are installed
in the printer.
The letter before the number indicates the location of the font, as
shown below.
I: Internal font
S: Soft (downloaded) font
M: Fonts in optional CompactFlash card
H: Fonts in RAM disk or optional hard disk
>>?I000
Press U or V repeatedly until the desired font number appears. For

font numbers of the internal fonts, refer to Print Fonts List on page 715.
6
7
When the desired font is displayed, press [OK].

Selecting Regular or Dark Courier/Letter Gothic

Courier or Letter Gothic font thickness can be selected as Regular or
Dark. In the procedure below, it is assumed that Courier is selected. The
procedure is the same for Letter Gothic.
>Font Select
Internal
>
1
2

7-41
>>Courier
Regular
>>Courier
?Regular
3
4
Make sure that Internal is displayed and press Z.
6
7
8
Select Regular or Dark using U or V.
Press U or V repeatedly until >>Courier appears. If you are

selecting the thickness of the Letter Gothic font, choose >>Letter
Gothic here instead.
Press [OK].
Changing the Default Font Size

You can change the size of the default font. If you selected a proportional
font, the character size can also be changed.
>Font Select
Internal
>
>>Size
012.00 point(s)
1
2
3
4

cursor. The font size can be set between 4 and 999.75 points, in
0.25-point increments. Use Z or Y to move the cursor right and left.
7
8
When the desired size is displayed, press [OK].
Press U or V repeatedly until >>Size appears.
>>Size
012.00 point(s)
7-42
Character Pitch
You can set the character pitch for fixed fonts.
>Font Select
Internal
>
>>Pitch
1
2
3
4

cursor. The character pitch can be set 0.44 and 99.99 characters per
inch, in 0.01 character-per-inch increments. Use Z or Y to move the
cursor right and left.
7
8
Press U or V repeatedly until >>Pitch appears.
10.00 cpi
>>Pitch
10.00 cpi
Code Set (Setting the code set)

You can change the character code set. Available character code sets
vary depending on the current font. (The default is IBM PC-8.)
>Code Set
IBM PC-8
>Code Set
?IBM PC-8
1
2
4
5
6
Press U or V until the desired character code set appears.
Press U or V repeatedly until >Code Set appears.
Press [OK].
7-43
Print Quality (Setting print quality)

In Print Quality menus, you can set the KIR mode, EcoPrint mode, and
other settings.
The options available in Print Quality are as follows:
>Print Quality >
KIR Mode (Selecting the KIR mode)

EcoPrint Mode (Selecting the EcoPrint mode)
Resolution (Selecting the Print Resolution)
Print Density (Selecting the Print Density)
1
2

Press U or V repeatedly until >Print Quality > appears.
KIR Mode (Selecting the KIR mode)

This printer incorporates the KIR (Kyocera Image Refinement)
smoothing function. KIR users the software to enhance resolution,
resulting in high quality printing at resolution of 600 dpi and 300 dpi. The
default is On. KIR has no effect on the printing speed.
with KIR Off
with KIR On (default)
Note Set the print density to 03 when setting the KIR mode. For
details on the print density, refer to Print Density (Selecting the
print density) on page 7-45.
>>KIR Mode
? On
7-44
1
2
3
Press Z while >Print Quality > is displayed.
4
5
6
Press U or V repeatedly until >>KIR Mode appears.

Press [OK].
EcoPrint Mode (Selecting the EcoPrint mode)

By enabling EcoPrint mode, you can minimize the amount of toner used
during printing. Because images printed in this mode may be slightly
coarser than those printed in standard resolution, you should use
EcoPrint for test prints or other situations where high-quality prints are
not required.
EcoPrint setting is
Off (default)
EcoPrint setting is
On
Use the procedure below to select EcoPrint mode. The default setting is
Off.
>>EcoPrint Mode
? Off
1
2
3
4
5
6
Press U or V repeatedly until >>EcoPrint Mode appears.

Press [OK].
Resolution (Selecting the print resolution)

You can set the default print resolution in four ways: 300dpi, 600dpi, Fast
1200 mode and Fine 1200 mode. The clarity of printed characters and
graphics becomes sharper in this order.
>>Resolution
? Fast 1200 mode
1
2
3
Select Fine 1200 mode, Fast 1200 mode, 600 dpi or 300
dpi using the U or V.
5
6
Press [OK].
Press U or V repeatedly until >>Resolution appears.

Print Density (Selecting the print density)

The print density can be adjusted in five steps: from 01 (light) to 05
(dark). The default setting is 03.
>>Print Density
? 03
1
2
3

Press U or V repeatedly until >>Print Density appears.
7-45
Select the print density from five steps from 01 (light) to 05 (dark)
using the U or V.
5
6
Press [OK].
Page Set (Setting pagination)

In Page Set menus, you can set the number of copies, page orientation,
and other settings regarding pagination.
The options available in Page Set are as follows:
>Page Set
>

Orientation (Print orientation)
LF Action (Linefeed)
CR Action (Carriage-Return)
Wide A4 (Wide A4 pitch)
1
2

Press U or V repeatedly until >Page Set
> appears.

You can set the number of copies of each page to be printed.
>>Copies
1
2
3
Press Z while >Page Set > is displayed.
Press U or V to increase or decrease, respectively, the value at the

blinking cursor. The number of copies can be set between 1 and
999. Use Y and Z to move the cursor right and left.
5
6
Press U or V repeatedly until >>Copies appears.

001
Zoom (Reduce print)

You can print with the reduced size. This menu is used to set the source
paper size and the paper size to use after reduction.
Note Printed results when making reductions differ from
equivalent size printing. Sometimes the line width of characters
may not be consistent or lines may appear in figures or image
patterns. Also, thin lines may not be reproduced on the reduced
print.
In the reduction mode, printed barcodes may not be read.
7-46
Bring up the Zoom menu. The following

display will appear.
Source size indicator:
This is the paper size before reduction.
This must be the same as the paper size
set for print data from the computer.
Target size indicator:
This is the paper size after reduction.
This must be the same as the paper size
set for the paper cassette.
>>Zoom
[CS]->[CS]
Target size
indicator
Source size indicator
The display will show the messages given in the following table.
Source size indicator
Target size indicator
[CS]
Current cassette size
[CS]
[CS]98%
[LG]
Legal size (8-1/2 14 inches)
[LG]
[LG]98%
[LT]
Letter size (8-1/2 11 inches)
[LT]
[A4]
[LT]98%
[LD]
Ledger size
(11 17 inches)
[LD]
[LD]98%
[O2]
[O2]
[FO]
[FO]
[8K]
[8K]
[16K]
[16K]
[A5]
(148 210 mm)
[A5]
[A5]98%
[B5]
(182 257 mm)
[B5]
[A5]
[B5]98%
[A4]
(210 297 mm)
[A4]
[LT]
[B5]
[A5]
[A4]98%
[B4]
(257 364 mm)
[B4]
[B5]
[A4]
[B4]98%
[A3]
(297 420 mm)
[A3]
[A4]
[B4]
[A3]98%
7-47
>>Zoom
[CS]->[CS]
>>Zoom
[CS]->[CS]
2
3
Press U or V repeatedly until >>Zoom appears.
Press U or V to select source size. The both sizes change

simultaneously.
5
6
Press Z to move the cursor to the target size.
7
8
Press [OK].
Press [OK]. A blinking cursor (_) appears under the source size.
To make a reduced print, press U or V to select the target size.
Orientation (Print orientation)

You can select portrait (upright) or landscape (sideways) page
orientation.
Portrait Orientation
>>Orientation
? Portrait
7-48
Landscape Orientation
1
2
3
4
5
6
Select Portrait or Landscape using U or V.
Press U or V repeatedly until >>Orientation appears.

Press [OK].
LF Action (Linefeed)
This procedure instructs the printer what to do when it receives a
linefeed code (0AH).
>>LF Action
? LF only
LF only: Linefeed is performed (Default).

CR and LF: A linefeed and carriage return are performed.
Ignore LF: The linefeed is ignored.
1
2
3
4
5
6
Press U or V repeatedly until the desired linefeed action appears.
Press U or V repeatedly until >>LF Action appears.

When the desired action is displayed, press [OK].

CR Action (Carriage-Return)
This procedure instructs the printer what to do when it receives a
carriage return code (0DH).
>>CR Action
? CR only
CR only: A carriage-return is performed (Default).

CR and LF: A linefeed and carriage return are performed.
Ignore CR: The carriage-return is ignored.
1
2
3
4
5
6
Press U or V repeatedly until the desired carriage-return appears.
Press U or V repeatedly until >>CR Action appears.

When the desired action is displayed, press [OK].

Wide A4 (Wide A4 pitch)

Turn this to On to increase the maximum number of characters that can
be printed in a line for an A4 page (78 characters at 10 pitch) and Letter
size page (80 characters at 10 pitch). This setting is only effective in PCL
6 emulation.
>>Wide A4
? Off
1
2
3
4
5
6
Press U or V repeatedly until >>Wide A4 appears.

Press [OK].
7-49
Network (Network settings)

This printer supports TCP/IP and TCP/IP (IPv6) protocols.
IP is an abbreviation for Internet Protocol. This printer routinely uses the
TCP/IP (IPv4) protocol, but provides a separate setting for the nextgeneration IP, IPv6.
TCP/IP (IPv4) uses 32-bit IP addresses, but the rapid growth in the
number of Internet users has resulted in a shortage of IP addresses.
IPv6 was developed to expand the range of available IP addresses by
using 128-bit IP addresses.
The options available in the Network settings are as follows:
TCP/IP (IPv4 settings)

TCP/IP (IPv6) (IPv6 settings)
Note Check with your network administrator when selecting the
network setting.
After all network related settings have been done, turn the
machine OFF and ON again. This is mandatory to make the
settings effective.
Network
>
1
2
Press [MENU].
Press U or V repeatedly until Network > appears.
TCP/IP (IPv4 settings)

This selects the settings for TCP/IP (IPv4).
The TCP/IP system refers to the Internet system, which has a 5-layer
structure consisting of the interface layer, link layer, network (IP) layer,
transport (TCP/UDP) layer and application layer.
The interface layer is a key layer in the TCP/IP system that provides an
abstracted interface that is not dependent on the link (communication
line: frame relay or Ethernet, etc.) to the IP module (IP layer). This
means that the IP module can use this abstracted interface (which is not
dependent on the link type) to exchange IP packets back and forth with
the link layer.
The options available in the TCP/IP (IPv4) settings are as follows:
DHCP (DHCP setting)

IP Address (IP address setting)
Subnet Mask (Subnet mask setting)
Gateway (Gateway setting)
Bonjour (Bonjour setting)
IMPORTANT The DHCP, IP address, subnet mask, gateway and

Bonjour menu options for TCP/IP are displayed when TCP/IP is
enabled.
>TCP/IP
? Off
7-50
1
2
3
Press Z while Network > is displayed.

Press U or V repeatedly until >TCP/IP > appears.
4
5

Select On and press [OK]. The display changes to the settings
shown below.
DHCP (DHCP setting)

DHCP (Dynamic Host Configuration Protocol) is the protocol that
assigns the information required to establish a network connection when
a host attempts to connect to the network (Internet). This information
includes the IP address of the local node and the default router (the
router in the host's own network system) and the DNS (Domain Name
System) server. DHCP is an extension of the BOOTP (Bootstrap) startup
protocol.
>>DHCP
? Off
1
2
3
Press Z while >TCP/IP On > is displayed.
4
5
6
Press U or V repeatedly until >>DHCP appears.

Press [OK].
IP Address (IP address setting)

An IP address is the address of a network device such as a computer
and is included in IP packets as needed for the sending and receiving of
Internet data (IP packets). (IP addresses can be either destination
addresses or source addresses.)
Specifically, an IP address is a bit string consisting of a host address (or
host section) that identifies a computer (host) connected to the Internet
and a network address (or network section) that identifies the network to
which that computer belongs (or more specifically, the computer's
network interface). Bit strings (IP addresses) that are unique throughout
the entire Internet system are allocated to each computer or interface.
The IP addresses currently used on the Internet (IPv4) have a fixed
length of 32 bits.
Note When you enter the IP address, be sure to set the DHCP
setting to Off.
>>IP Address
000.000.000.000
1
2
3

blinking cursor. You can set any value between 000 and 255. Use Y
and Z to move the cursor right and left.
5
6
Display the desired IP address and press [OK].
Press U or V repeatedly until >>IP Address appears.

7-51
Subnet Mask (Subnet mask setting)

The subnet mask is a way of augmenting the network address section of
an IP address.
A subnet mask represents all network address sections as 1 and all host
address sections as 0. The number of bits in the prefix indicates the
length of the network address. The term "prefix" refers to something
added to the beginning and, in this context, indicates the first section of
the IP address.
When an IP address is written, the length of the network address can
indicated by the prefix length after a forward slash (/). For example, "24"
in the address "133.210.2.0/24". In this way, "133.210.2.0/24" denotes
the IP address "133.210.2.0" with a 24-bit prefix (network section).
This new network address section (originally part of the host address)
made possible by the subnet mask is referred to as the subnet address.
Note When you enter the subnet mask, be sure to set the DHCP
setting to Off.
>>Subnet Mask
000.000.000.000
1
2
3

5
6
Display the desired subnet mask and press [OK].
Press U or V repeatedly until >>Subnet Mask appears.

Gateway (Gateway setting)

Gateway generally refers to a protocol conversion device used to allow
networks with differing protocol systems to interconnect.
For example, a "Gateway" device is required to connect a different
closed network (using its own protocols) to the open Internet (using
TCP/IP).
By installing a gateway, the communications protocols and data display
modes on different networks can be made compatible.
On TCP/IP networks, the term gateway is used to refer to routers.
Note Before you input the gateway, be sure to set the DHCP
setting to Off.
>>Gateway
000.000.000.000
7-52
1
2
3

5
6
Display the desired gateway and press [OK].
Press U or V repeatedly until >>Gateway appears.

Bonjour (Bonjour setting)

Bonjour, also known as zero-configuration networking, is a service that
automatically detects computers, devices and services on an IP network.
Bonjour, because an industry-standard IP protocol is used, allows
devices to automatically recognize each other without an IP address
being specified or DNS server being set.
Bonjour also sends and receives network packets by UDP port 5353. If a
firewall is enabled, the user must check that UDP port 5353 is left open
so that Bonjour will run correctly. Some firewalls are set up so as to
reject only certain Bonjour packets. If Bonjour does not run stably, check
the firewall settings and ensure that Bonjour is registered on the
exceptions list and that Bonjour packets are accepted. If you install
Bonjour on Windows XP Service Pack 2 or later, the Windows firewall
will be set up correctly for Bonjour.
>>Bonjour
? Off
1
2
3
4
5
6
Press U or V repeatedly until >>Bonjour appears.

Press [OK].
TCP/IP (IPv6) (IPv6 settings)

This selects the settings for TCP/IP (IPv6).
TCP/IP (IPv6) is based on the current Internet protocol, TCP/IP (IPv4).
IPv6 is the next-generation Internet protocol and expands the available
address space, which resolves the problem of the lack of addresses
under IPv4, while also introducing other improvements such as
additional security functionality and the capacity to prioritize data
transmission.
The options available in the TCP/IP (IPv6) settings are as follows:
RA(Stateless) (RA (Stateless) setting)

DHCPv6 (DHCPv6 setting)
IMPORTANT The RA (Stateless) and DHCPv6 menu options for

TCP/IP (IPv6) are displayed when TCP/IP (IPv6) is enabled.
>TCP/IP (IPv6)
? Off
1
2
3
Press Z while Network > is displayed.
4
5
Press U or V repeatedly until >TCP/IP (IPv6) > appears.

Select On and press [OK].The display changes to the settings

shown below.
7-53
RA(Stateless) (RA (Stateless) setting)

The IPv6 router communicates (transmits) information such as the global
address prefix using ICMPv6. This information is the Router
Advertisement (RA).
ICMPv6 stands for Internet Control Message Protocol, and is a IPv6
standard defined in the RFC 2463 "Internet Control Message Protocol
(ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification".
>>RA(Stateless)
? Off
1
2
3
Press Z while >TCP/IP (IPv6) On > is displayed.
4
5
6
Press U or V repeatedly until >>RA(Stateless) appears.

Press [OK].
DHCPv6 (DHCPv6 setting)

DHCPv6 is the next-generation of the Internet's Dynamic Host
Configuration Protocol and supports IPv6. It extends the BOOTP startup
protocol that defines the protocols used for transferring configuration
information to hosts on the network.
DHCPv6 permits the DHCP server to use its expanded functionality to
send configuration parameters to an IPv6 node. Because the network
addresses that can be used are allocated automatically, the IPv6 node
management workload is reduced in systems where the administrator
has to exercise close control over IP address allocation.
>>DHCPv6
? Off
7-54
1
2
3
Press Z while >TCP/IP (IPv6) On > is displayed.
4
5
6
Press U or V repeatedly until >>DHCPv6 appears.

Press [OK].
Device Common (Selecting/Setting the

common device)
Selects/sets all the functions in this printer.
The options available in Device Common are as follows:
MSG Language (Selecting the message language)

Buzzer (Alarm (Buzzer) setting)
RAM Disk Mode (Using the RAM disk)
Hard Disk (Using the optional hard disk)
Memory Card (Using the memory card)
Error Handling (Error detection setting)
Timer (Timer setting)
Note The Hard Disk and Memory Card menu are only
displayed when a hard disk and CF card are installed in the

printer.
Device Common
>
1
2
Press [MENU].
Press U or V repeatedly until Device Common > appears.
MSG Language (Selecting the message language)

You can select the language of the message display by following the
procedure given below. You can optionally download messages in other
languages. Contact your service technician for information.
1
2
>MSG Language
? English
Press Z while Device Common > is displayed.

Press U or V repeatedly until >MSG Language appears. The
default message language is English.
To change the language, press [OK]. A blinking question mark (?)

appears.
Press U or V. The display cycles through the available selection in

the following order:
English
Franais
Deutsch
Italiano
Nederlands
Espaol
Portugus
5
6
Press [OK].
7-55
Buzzer (Alarm (Buzzer) setting)

This function uses tones to notify the user of printer operations and the
printer status. This setting is useful, for example, when the printer is
located some distance from the user.
The options available in Buzzer are as follows:
>Buzzer
>
Key Confirm. (Key confirmation tone setting)

Job End (Job completed tone setting)
Ready (Preparation completed tone setting)
Error (Error tone setting)
1
2

Press U or V repeatedly until >Buzzer > appears.
Key Confirm. (Key confirmation tone setting)

When On is selected in this setting, a tone sounds each time a key is
used. The default setting is On.
>>Key Confirm.
? On
1
2
3
Press Z while >Buzzer > is displayed.
4
5
6
Press U or V repeatedly until >>Key Confirm. appears.

Press [OK].
Job End (Job completed tone setting)

When On is selected in this setting, a tone sounds when printing ends.
The default setting is Off.
>>Job End
? Off
7-56
1
2
3
4
5
6
Press U or V repeatedly until >>Job End appears.

Press [OK].
Ready (Preparation completed tone setting)

When On is selected in this setting, a tone sounds when print preparation
has been completed. The default setting is Off.
>>Ready
? Off
1
2
3
4
5
6
Press U or V repeatedly until >>Ready appears.

Press [OK].
Error (Error tone setting)

When On is selected in this setting, a tone sounds when a problem such
as running out of paper or a paper jam occurs during printing. The
default setting is On.
>>Error
? On
1
2
3
4
5
6
Press U or V repeatedly until >>Error appears.

Press [OK].
7-57
RAM Disk Mode (Using the RAM disk)

The RAM disk is a memory space shared within the printer memory that
can temporarily store print jobs. The stored print job can then be used to
print multiple copies of the job reducing the total amount of time required
to print the whole job. It acts similar to the hard disk except that the data
is effective only when the printer is powered up.
To use the RAM disk, activate and enter the desired size of the RAM disk
in the manner described below. The maximum RAM disk size can be
calculated as follows:
When the RAM disk is activated = The maximum RAM disk size is 4MB
(when no options are attached)
When the optional memory is installed = The maximum RAM disk size is
1/2 of the total optional memory installed
To activate RAM disk in the printer's memory, first you must set the RAM
disk mode to On and set the desired data size for the RAM disk as
described in the following section. This allows you to perform the
following operations on the RAM disk.
Note The printer supports three types of storage device; CF card,
optional hard disk, and RAM disk. The CF card and optional hard
disk are installed into the dedicated slots of the printer. The RAM
disk is an allocated part of the printers memory.
IMPORTANT The RAM disk can not be used when an optional hard
disk is installed.
The RAM disk stores data only temporarily. When the printer is reset
or turned off, the stored data will be erased.
The RAM disk allows some Job Box functions to be used.
The RAM disk is allocated from the printer memory available to users.
If the size of the RAM disk is set too large, the printing speed may
decrease or the memory may become insufficient.
>RAM Disk Mode

? Off
7-58
1
2
3
4
5
6
Press U or V repeatedly until >RAM Disk Mode > appears.

Press [OK].
RAM Disk Size (Setting the RAM disk size)

Use this procedure to set the amount of memory used for the RAM disk.
IMPORTANT The RAM Disk Size menu option only appears when
RAM Disk Mode is set to On.
>>RAM Disk Size

119MByte
1
2
Press Z while >RAM Disk Mode On > is displayed.

Press [OK]. The message display shows a blinking cursor (_). Press
U or V to display the desired size. Definable RAM disk size is 001
to 512. Use Y and Z to move the cursor right and left.
This range varies depending on the total memory size of the printer.
The setting exceeding this range is automatically adjusted to the
maximum RAM disk size.
3
4
When the desired RAM disk size is displayed, press [OK].

Press [MENU]. The display returns to Ready. Turn the printer off
and then on again. The selected RAM disk size is activated after the
printer is restarted.
Hard Disk (Using the optional hard disk)

Installing the optional hard disk into the printer allows you to perform the
following operations on the hard disk.
Format (Formatting hard disk)
When an optional hard disk is inserted into the printer for the first time, it
must be formatted before use.
the printer.
Note The Hard Disk menu options are only displayed when a
hard disk is installed in the printer. If the optional hard disk is
installed in the printer, the Job Box will be available.
>Hard Disk
>
1
2

Press U or V repeatedly until >Hard Disk > appears.
7-59
Format (Formatting hard disk)

A new hard disk must be formatted before it can be used in the printer.
Formatting allows data to be written to the hard disk.
the printer.
Note Formatting will destroy any existing data on a storage device
including a used CF card.
Formatting of the hard disk must be executed from the printer.
>>Format ?
1
2
3
Press Z while >Hard Disk > is displayed.
Press [OK].
>>Format appears.
Processing appears and formatting of the hard disk starts. When

the formatting is successfully completed, the display returns to
Ready.
Memory Card (Using the CF card)

The printer is equipped with a slot for a CF card (memory card). By
inserting a CF card into the printer, the following operations become
available.
Format (Formatting CF card)
For details about the handling of the CF card, refer to CompactFlash

(CF) Card on page 8-7.
Note The Memory Card menu options are only displayed when
a CF card is installed in the printer.
>Memory Card
7-60
>
1
2

Press U or V repeatedly until >Memory Card > appears.
Format (Formatting CF card)

A new CF card must be formatted before it can be used in the printer.
Formatting allows data to be written to the CF card.
Note Format is only displayed when a CF card is installed in the
printer and protection is disabled.
Formatting will destroy any existing data on a storage device
including a used CF card.
Formatting of the CF card must be executed from the printer.
When a new CF card is inserted in the printer's slot, Format error
Memory card will appear on the message display.
>>Format ?
1
2
3
Press Z while >Memory Card > is displayed.
Press [OK].
>>Format appears.
Processing appears and formatting of the CF card starts. When

the formatting is successfully completed, the display returns to
Ready.
Error Handling (Error detection setting)

This specifies the settings for the detection methods used for duplex
printing errors and for paper size and paper type errors when the paper
source is fixed.
The options available in Error Handling are as follows:
>Error Handling>
Duplex (Duplex printing error detection setting)

Paper Mismatch (Detection settings for paper size/type errors when
the paper source is fixed)
1
2

Press U or V repeatedly until >Error Handling > appears.
7-61
Duplex (Duplex printing error detection setting)

If the error detection setting for duplex printing has been turned On, and
you attempt to print onto a paper size and paper type that cannot be
used for duplex printing, the Duplex disabled Press GO error
message will be displayed and printing will stop. The default settings is
Off.
On
Off
>>Duplex
? Off
To print onto one-side of the paper only when this

message is displayed, press [GO].
Press [Cancel] to cancel the printing itself.
To print onto one-side of the paper.
1
2
3
Press Z while >Error Handling > is displayed.
4
5
6
Press U or V repeatedly until >>Duplex appears.

Press [OK].
Paper Mismatch (Detection settings for paper size/type errors

when the paper source is fixed)
This interrupts printing by indicating Paper Mismatch when the paper
sizes and/or types do not match between a print job and a paper source.
This can be disabled if you want to continue printing even if the paper
size or type you specified is different from the fixed paper source. The
default setting is On.
Note This setting does not relate to the Size Error. The Size
Error will be indicated when the Paper Size Dial and the actual
paper size do not match. For details on Size Error, refer to Error
Message of Troubleshooting.
>>Paper Mismatch
? On
7-62
1
2
3
Press Z while >Error Handling > is displayed.

On: stops printing and an error message appears
Off: continues printing
5
6
Press [OK].
Press U or V repeatedly until >>Paper Mismatch appears.

Timer (Timer setting)

This specifies timer-related settings such as the automatic form-feed
timeout and the timeout settings for Auto Sleep.
The options available in Timer are as follows:
>Timer
>
Form Feed Time Out (Automatic form feed timeout setting)

Sleep Timer (Sleep timer timeout time)
Auto Error Clear (Auto error clear setting)
Error Clear Timer (Setting the error clear time)
Auto Panel Reset (Auto panel reset settings)
Panel Reset Timer (Setting the panel reset timer)
Auto Sleep (Setting the sleep timer)
1
2

Press U or V repeatedly until >Timer > appears.
Form Feed Time Out (Automatic form feed timeout setting)

If the printer receives no data for a certain period, it will time out and
release the current interface. It prints whatever data it has in its buffer
and feeds out the page. The default form feed timeout time is 30
seconds.
>>Form Feed
Time Out 030sec.
1
2
3
Press Z while >Timer > is displayed.

cursor and set the desired time. The timeout time can be between 5
and 495 seconds, in 5-second increments. Use Y and Z to move
the cursor right and left.
5
6
Press [OK].
Press U or V repeatedly until >>Form Feed Time Out appears.

7-63
Sleep Timer (Sleep timer timeout time)

You can adjust the length of time the printer waits before entering Auto
Sleep in the absence of data.
The printer reverts to normal operation mode when the printer receives a
print job, the operation panel is operated, or one of the exterior covers is
opened. The default time is 30 minutes (FS-2020D/3920DN/4020DN)/5
minutes (FS-6970DN).
Note Calibration is automatically executed before the printer
reverts to normal operation mode.
>>Sleep Timer
030 min.
7-64
1
2
3

cursor and set the desired time. The timer can be set between 1 and
240 minutes. Use Y and Z to move the cursor right and left.
5
6
Press [OK].
Press U or V repeatedly until >>Sleep Timer appears.

To change the timeout time, press [OK]. A blinking cursor (_)
appears.
Auto Error Clear (Auto error clear setting)

If an error that still allows you to continue printing occurs, the next
received data is automatically printed after a set period of time elapses.
For example, if the printer is shared over a network as a network printer
and one person causes one of the above errors, after the set period of
time elapses, the data sent from the next person is printed. The default
setting is Off (Auto Error Clear disabled).
The auto clear errors are:
Memory overflow Press GO

Print overrun Press GO
KPDL error
## Press GO
Hard disk err ## Press GO
RAM disk error## Press GO
MemoryCard err## Press GO
Illegal Account Press GO
Exceeded Max.out Press GO
Job restricted Press GO
Account error ## Press GO
Duplex disabled Press GO
Job not stored Press GO
No multi copies Press GO
USB memory err## Press GO
For setting the auto error clear recovery time, refer to the next section
Error Clear Timer (Setting the error clear time).
>>Auto Error
Clear ? Off
1
2
3
4
5
6
Press U or V repeatedly until >>Auto Error Clear appears.

Press [OK].
Error Clear Timer (Setting the error clear time)

If Auto Error Clear is set to On and a non-fatal error (an error that
allows printing to continue) occurs, this setting specifies the time until the
error is recovered and printing resumes. The default time is 30 seconds.
>>Error Clear
Timer
030sec.
1
2
3

cursor and set the desired time. The time must be set between 5 and
495 seconds, in 5-second increments. You can use Y and Z to
move the cursor right and left.
5
6
Press [OK].
Press U or V repeatedly until >>Error Clear Timer appears.

7-65
Auto Panel Reset (Auto panel reset settings)

The Auto Panel Reset function automatically restores the default
settings if the panel is not used for a set time. The default setting is On.
For setting the time until the panel is reset, refer to the next section
Panel Reset Timer (Setting the panel reset timer).
>>Auto Panel
Reset ? On
1
2
3
4
5
6
Press U or V repeatedly until >>Auto Panel Reset appears.

Press [OK].
Panel Reset Timer (Setting the panel reset timer)

When Auto Panel Reset is set to On, this sets the time until the panel is
automatically reset after the user stops using the panel. The default time
is 90 seconds.
>>Panel Reset
Timer
090sec.
1
2
3

cursor and set the desired time. The time must be set between 005
and 495 seconds, in 5-second increments. Use Y and Z to move
the cursor right and left.
5
6
Press [OK].
Press U or V repeatedly until >>Panel Reset Timer appears.

Press [OK]. The message display shows a blinking cursor (_).
Auto Sleep (Setting the sleep timer)

The printer has a sleep timer that is used to conserve power when the
printer is not printing, processing, or receiving data. The default setting is
On.
>>Auto Sleep
? On
7-66
1
2
3
4
5
6
Press U or V repeatedly until >>Auto Sleep appears.

To turn off the sleep timer, press [OK]. A blinking question mark (?)
appears.
Press [OK]. The sleep timer is turned off.

Security
The security functions can be set up to protect printer operation and the
print data.
The options available in Security are as follows:
Security
>
ID (Administrator ID input)
Password (Administrator password input)
I/F Block (Interface (external device) block setting)
NetWare (NetWare setting)
AppleTalk (AppleTalk setting)
IPP (IPP setting)
SSL Server (SSL Server setting)
IPSec (IPSec setting)
Security Level (Security level setting)
1
2
Press [MENU].
Press U or V repeatedly until Security > appears.
To use the Security function, you must enter an administrator ID. For
information on how to set the administrator ID, refer to Admin
(Administrator settings) on page 7-81.
ID
_
1
2
Press Z while Security > is displayed.

blinking cursor. Enter the specified ID. Use Y and Z to move the
cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
Press [OK]. Proceed to the next step Password (Administrator

Password input).
The message display shows ID and a blinking cursor (_).
7-67
Password (Administrator Password input)

To set up the Security functions, you must enter an administrator ID and
administrator password. For information on how to set the administrator
password, refer to Admin (Administrator settings) on page 7-81.
Password
_
When you entered the ID in the previous step (ID (Administrator ID

input)), the message display shows Password (Administrator
password input) and a blinking cursor (_).

blinking cursor. Enter the specified password. Use Y and Z to move
the cursor right and left. Enter a password consisting of between 0
and 16 numbers.
Note If you enter an incorrect administrator ID or password,
the message Wrong ID or Wrong Password appears and
the input screen then reappears. Re-enter the password
correctly.
Press [OK]. The Security screen appears.
I/F Block (Interface (external device) block setting)

You can use this to lock and thereby protect the interface. The options
available in Interface Block are as follows:
>I/F Block
>
USB Host (USB memory slot setting)

USB Device (USB interface setting)
Parallel I/F (Parallel interface)
Option I/F (Network interface card setting)
After entering the administrator ID and password, press U or V

repeatedly until >I/F Block > appears.
USB Host (USB memory slot setting)

This locks and protects the USB memory slot (USB host). The default
setting is Unblock.
>>USB Host
? Unblock
7-68
1
2
Press Z while >I/F Block > is displayed. >>USB Host appears.
3
4
5
Select Block or Unblock using U or V.
Press [OK].
USB Device (USB interface setting)

This locks and protects the USB interface. The default setting is
Unblock.
>>USB Device
? Unblock
Press Z while >I/F Block > is displayed. >>USB Device

appears.
3
4
5

Press [OK].
Parallel I/F (Parallel interface setting)

This locks and protects the parallel interface. The default setting is
Unblock.
>>Parallel I/F
? Unblock
Press Z while >I/F Block > is displayed. >>Parallel I/F

appears.
3
4
5

Press [OK].
Option I/F (Network interface card setting)

This locks and protects the network interface card (NIC). The default
setting is Unblock.
Note Option I/F is displayed only when the optional network
interface is installed on the printer.
>>Option I/F
? Unblock
Press Z while >I/F Block > is displayed. >>Option I/F

appears.
3
4
5

Press [OK].
7-69
NetWare (NetWare setting)

NetWare is a PC-based network operating system specifically for
servers.
NetWare is a client-server system that operates by installing the
NetWare OS on the server and dedicated client modules (NetWare
clients) on the client machines (running MS-DOS, OS/2, Windows, etc.).
The basic network layer protocol used is NetWare's own IPX
(Internetwork Packet eXchange)/SPX (Sequenced Packet eXchange),
but the system also supports TCP/IP.
The feature of the NetWare OS is that it is specifically for servers, unlike
general-purpose operating systems such as Windows NT and UNIX.
Only the minimum required for server operation can be performed from
the NetWare OS console on the server. Server and file management is
basically carried out using management tools from the clients. Also, all
drivers and protocol stacks are in the form of modules called NetWare
Loadable Modules (NLMs), and the ability of NLMs to load and unload
flexibly and dynamically is a major advantage of this system.
The default setting is On.
Note Check with your network administrator when selecting
network settings.
>NetWare
>
>NetWare
? On
>

repeatedly until >NetWare > appears.
3
4
5

Press [OK].
Frame Type (Frame type setting)

Sets the NetWare frame type. Frame is a term referring to a set of data
that flows through the network. The default setting is Auto.
>>Frame Type
? Auto
Press Z while >NetWare On > is displayed. >>Frame Type

appears.
Press U or V until the desired frame type appears and then press
[OK]. The message display toggles through the following types:
4
5
7-70
Auto
802.3
Ethernet-II
802.2
SNAP
Press [OK].
AppleTalk (AppleTalk setting)

AppleTalk is a communications protocol used primarily on Macintosh
computers and also refers to the Mac OS network functions.
AppleTalk assigns 24-bit network addresses (a 16-bit network section
and an 8-bit node address) that are used to identify devices (computers,
printers, etc.) on the network.
When the power is turned on, a broadcast signal is sent out onto the
network and the addresses and machine names are automatically
assigned.
The default setting is On.
network settings.
>AppleTalk
>AppleTalk
? On

repeatedly until >AppleTalk appears.
3
4
5

Press [OK].
IPP (IPP setting)

IPP (Internet Printing Protocol) is a standard that uses TCP/IP networks
such as the Internet to enable print jobs to be sent between remote
computers and printers.
IPP is an extension of the HTTP protocol used to view websites and
enables printing to be carried out via routers on printers in remote
locations. It also supports the HTTP authentication mechanisms along
with SSL server and client authentication as well as encryption.
network settings.
>IPP
>IPP
? Off

repeatedly until >IPP appears.
3
4
5

Press [OK].
7-71
SSL Server (SSL Server setting)

SSL (Secure Sockets Layer) refers to a protocol used to encrypt
information sent and received over a network. SSL can currently be used
to encrypt data such as the WWW or FTP files widely used on the
Internet so that privacy-related information, credit card numbers,
corporate secrets and other confidential information can be sent and
received safely.
SSL servers use this protocol to authenticate servers and clients.
network settings.
>SSL Server
>SSL Server
? Off

repeatedly until >SSL Server appears.
3
4
5

Press [OK].
DES (SSL Server DES setting)

DES (Data Encryption Standard) is a typical symmetric-key
cryptographic algorithm that divides data in to 64-bit blocks and then
encrypts each block using a 56-bit key.
Note Symmetric-key cryptography, because it uses the same key
for both encryption and decryption, uses the same key in both
directions when encrypted data is exchanged. Accordingly, to
prevent the key from being divulged, key transfer and storage must
be very strictly managed.
>>DES
? Off
7-72
1
2
Press Z while >SSL Server On > is displayed. >>DES appears.
3
4
5
Press [OK].
3DES (SSL Server 3DES setting)

3DES (Triple Data Encryption Standard) is a high level of encryption in
which DES encryption is repeated threefold.
>>3DES
? Off
1
2
Press Z while >SSL Server On > is displayed. >>3DES appears.
3
4
5
Press [OK].
AES (SSL Server AES setting)

AES (Advanced Encryption Standard) was developed to replace DES as
the standard encryption as the safety of DES has declined. AES is a
block encryption system that uses 128-bit blocks and an SPN structure
(a typical structure for repeated encryption) with three selectable key
lengths of 128, 192 and 256 bits.
>>AES
? Off
1
2
Press Z while >SSL Server On > is displayed. >>AES appears.
3
4
5
Press [OK].
IPP over SSL (SSL Server IPP over SSL setting)

IPP over SSL is an encryption function that uses SSL for
communications between users and servers in network printing. To use
IPP over SSL, both server and client must support the protocol.
>>IPP over SSL

? Off
Press Z while >SSL Server On > is displayed. >>IPP over SSL

appears.
3
4
5

Press [OK].
7-73
HTTPS (SSL Server HTTPS setting)

HTTPS (Hyper Text Transfer Protocol Secure) is a protocol that adds
SSL data encryption, message authentication and a digital signature
function to the HTTP protocol used for data transfer between WWW
servers and clients.
S-HTTP is a similar protocol, but HTTPS differs in that it uses SSL.
>>HTTPS
? Off
Press Z while >SSL Server On > is displayed. >>HTTPS

appears.
3
4
5

Press [OK].
IPSec (IPSec setting)

IPSec (IP Security Protocol) is a security protocol adopted as the
standard by the IETF for authentication and encryption in the third
network layer (IP layer).
It can be used with both IPv4 and IPv6.
Note IPv4 uses 32-bit IP addresses and IPv6 uses 128-bit IP
addresses.
network settings.
>IPSec
>IPSec
? Off

repeatedly until >IPSec appears.
3
4
5

Press [OK].
Press [Menu]. The display returns to Ready.
Security Level (Security level setting)

Security Level is primarily a menu used by service personnel for
maintenance work. There is no need for customers to use this menu.
7-74
Job Accounting (Job Accounting

selection/setting)
Job Accounting is a function that allows the number of pages used to be
managed by each department to be managed through the use of entered
account IDs.
Job accounting on this machine offers the following features:
Support for up to 100 departments
Department codes up to 8 digits long from 1 to 99999999
Collective print management for the same department code
Totaling of the number of pages used for each department
Specifiable limits (1 to 9,999,999) on the number of pages used
Resetting of the number of pages used for individual departments
The options available in Job Accounting are as follows:
Select Account (Department-specific settings)
Add Account (Department Registration)
Delete Account (Department Removal)
Print Job Accounting List (Job Accounting list output)
IMPORTANT Select Account and Delete Account are only

displayed if one or more department codes have been registered.
Also, Add Account is not displayed if the number of registered
accounts has already reached the permitted maximum.
Job Accounting >
1
2
Press [MENU].
Press U or V repeatedly until Job Accounting > appears.
To set up Job Accounting, you must enter an administrator ID. For
information on how to set the administrator ID, refer to Admin
(Administrator settings) on page -81.
ID
_
1
2
Press Z while Job Accounting > is displayed.

numbers.
Note If you enter an incorrect administrator ID, the Wrong ID

message appears and the input screen then reappears. Reenter the ID correctly.

Password input).
7-75

To set up Job Accounting, you must enter an administrator ID and
administrator password. For information on how to set the administrator
password, refer to Admin (Administrator settings) on page -81.
Password
_
After entering the ID in the previous step (ID (Administrator ID


and 16 numbers.
Note If you enter an incorrect administrator ID or password,
the message Wrong ID or Wrong Password appears and
the input screen then reappears. Re-enter the ID or password
correctly.
Press [OK]. The Job Accounting selection/setting screen reappears.

This allows you to turn the Job Accounting function On and Off. The
default setting is Off.
>Job Accounting
? Off

repeatedly until >Job Accounting appears.
3
4
5

Press [OK].
Job Accounting enabled

If department administration is enabled, an account ID entry screen
appears each time you retrieve a status page or list.
Enter Account
_
A blinking cursor (_) appears in the account ID entry screen.

blinking cursor. Enter the specified account ID. Use Y and Z to
move the cursor right and left. Enter an account ID consisting of
between 1 and 8 numbers.
Note If you enter an incorrect account ID, the input screen
reappears. Re-enter the account ID correctly.
7-76
Press [OK]. The account is confirmed and printing begins.
Select Account (Department-specific settings)

This specifies the functions used for managing individual account IDs.
The options available in Select Account are as follows:
>Select Account>
?00000000
Counter (Account-specific counter management)

Restriction (Print restriction selection)
Maximum Output (Maximum print output setting)
Reset Counter (Counter reset)
1
2
3
Each time you press U or V, the next registered account ID in the

sequence appears.
Display the desired account ID and press [OK]. Press Z, the display
changes to the individual department setting screen.
Press U or V repeatedly until >Select Account> appears.

Counter (Account-specific counter management)

Displays the total number of pages printed for the currently selected
account.
IMPORTANT You can only view the counter. You cannot change it.
>>Counter
0000100
Set the account ID and then press U or V repeatedly until

>>Counter appears. (E.g.: 100)
The counter shows a number between 0000000 and 9999999.
Restriction (Print restriction selection)

Sets restricted functionality for all printing on the currently selected
account. You can use the restrictions to prohibit printing by individual
departments or to limit the number of pages they can print.
>>Restriction
? Off

>>Restriction appears.
Press U or V repeatedly to select the desired restriction. The

displayed restrictions are as follows:
4
5
Off (no restrictions)

Counter Limit (to limit the number of pages)
Reject Usage (to prohibit printing)
Press [OK]. The restriction is set.

7-77
Maximum Output (Maximum print output setting)

Limits the number of pages for all printing on the currently selected
account.
>>Maximum Output
0000001

>>Maximum Output appears.

blinking cursor. Set the desired number of pages. You can set a
number between 0000001 and 9999999 as the number of pages.
Use Y and Z to move the cursor right and left.
4
5
Press [OK].
Reset Counter (Counter reset)

Resets the counter (pages used) for the currently selected account.
>>Reset Counter?
7-78
Set the account ID and then press U or V repeatedly until >>Reset

Counter appears.
3
4
Press [OK] again. The counter is reset.

Add Account (Department registration)

This allows you to add a new account for which printing is permitted.
IMPORTANT Because account IDs are managed as numeric strings,

"1" and "001" are handled as different accounts. Also, once Job
Accounting is enabled, no jobs are printed unless information is
attached showing the accounts from which the jobs are being printed.
>Add Account
_
1
2
3

blinking cursor. Set the desired account ID. You can set a number
between 1 and 8 digits. Use Y and Z to move the cursor right and
left.
Press U or V repeatedly until >Add Account appears.

Note If you enter an existing account ID, Wrong Account is

displayed and the input screen reappears. Re-enter the new
account ID.
5
6
Press [OK]. Account registration ends.

Delete Account (Department removal)

You can use this to delete a registered account.
IMPORTANT Because account IDs are managed as numeric strings,

"1" and "001" are handled as different accounts. Also, once Job
Accounting is enabled, no jobs are printed unless information is
attached showing the accounts from which the jobs are being printed.
>Delete Account
?001
1
2
3
Each time you press U or V, the next registered account ID in the

sequence appears.
Display the desired account ID and press [OK]. The account ID is

deleted.
Press U or V repeatedly until >Delete Account appears.

(E.g.: 001)
7-79
Print Job Accounting List (Job Accounting list

output)
This enables you to print the total number of pages for all accounts as a
Job Accounting list.
1
2
>Print Job
Accounting List?
7-80

Press U or V repeatedly until >Print Job Accounting List
appears.
When you press [OK] again, Processing appears and printing

begins.
Admin (Administrator settings)

The Administrator setting is a function that identifies a user who can use
the printer and manage other users.
When using the Security and Job Accounting functions, the administrator
ID and password set here are authenticated, and settings can be
specified after they are properly authenticated.
The options available in Admin are as follows:
Admin
>
Password (Administrator password input)
Change ID (Administrator ID change)
Change Password (Administrator password change)
1
2
Press [MENU].
Press U or V repeatedly until Admin > appears.
You can use this to set the administrator ID. The default setting is the
numeric part of your printer's model name. If you use FS-2020D, enter
"2020".
ID
_
1
2
Press Z while Admin > is displayed.

numbers.

Password input).

You can use this to set the administrator password. The default setting is
the numeric part of your printer's model name. If you use FS-2020D,
enter "2020".
Password
_
When you entered the ID in the previous step (ID (Administrator ID


and 16 numbers.
Note If you enter the incorrect administrator ID or password,
the Wrong ID or Wrong Password message appears and
the input screen then reappears. Re-enter the ID or password
correctly.
7-81
>Change ID
00000001
Once you enter the correct ID and password, the Admin (change)
screen appears. (E.g.: Where the administrator ID is 00000001)
Each time you press U or V, the following settings to be changed
appear in succession.
Change ID
Change Password
Change ID (Administrator ID change)

You can use this to change the administrator ID.
>Change ID
001
>Change ID
_
OK?
002
In step 3 in Password (Administrator Password input) above, press

U or V while the Admin (Change) screen is displayed until
>Change ID appears. (E.g.: Where the administrator ID is 001)
When you press [OK], a blinking cursor (_) appears.

blinking cursor. Enter the ID to be changed. Use Y and Z to move
the cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
Press [OK]. A confirmation screen appears. (E.g.: Where the

administrator ID is changed to 002)
5
6
Press [OK]. The new administrator ID is confirmed.

Change Password (Administrator Password change)

You can use this to change the administrator password.
>Change Password
****************
In step 3 in Password (Administrator Password input) above, press

U or V while the Admin (Change) screen is displayed until
>Change Password appears.
IMPORTANT The administrator password is not displayed.
>Change Password
_
OK?
010
7-82

blinking cursor. Enter the password to be changed. Use Y and Z to
move the cursor right and left. Enter a password consisting of
between 0 and 16 numbers.
Press [OK]. A confirmation screen appears. (E.g.: Where the

administrator password is changed to 010)
5
6
Press [OK]. The new administrator password is confirmed.

Adjust/Maintenance (Adjust/Maintenance
selection/setting)
Adjust/Maintenance is used to adjust the print quality and to carry out
printer maintenance.
The options available in Adjust/Maintenance are as follows:
Restart Printer
Service (for maintenance)

use this menu.
Adjust/
Maintenance
>
1
2
Press [MENU].
Press U or V repeatedly until Adjust/Maintenance > appears.
Restart Printer
The procedure described below resets the printers temporary
conditions, such as the current page orientation, font, etc., set by
commands to their default values. Downloaded fonts and macros are
deleted from the printers memory.
>Restart
Printer ?
1
2
3
Press [OK] again. Self test appears while the printer is resetting
itself, followed by Ready.
Press U or V repeatedly until >Restart Printer appears.

7-83
Service (for maintenance)

The options available in Service are as follows:
Print Status Page (Printing the service status page)

Print Network Status Page (Printing the network status page)
Print Test Page (Printing the test page)
Developer (Initializing the developer unit)
DRUM-CTRL (Setting the automatic drum surface refreshing)
Drum (Setting the drum refleshing mode)

use this menu.
>Service
>
1
2

Press U or V repeatedly until >Service > appears.
Print Status Page (Printing the service status page)

The service status page contains printer settings information that is more
detailed than the standard status page and is therefore mostly for service
purposes. However, there is a great deal of information on the service
status page that may be useful to you.
>>Print
Status Page ?
1
2
3
Press Z while >Service > is displayed.
Press [OK] again. Processing appears and a service status page

is printed out.
Press U or V repeatedly until >>Print Status Page appears.

Print Network Status Page (Printing the network status page)

The network status page contains detailed information on the network
settings. This is primarily used for maintenance by service personnel, but
it contains information that may also be useful to you.
1
2
>>Print Network
Status Page ?

Press U or V repeatedly until >>Print Network Status Page
appears.
Press [OK] again. Processing appears and a network status page

is printed out.
Print Test Page (Printing the test page)

The test page is printed to check the effectiveness of printer
adjustments. This is primarily used for maintenance by service
personnel, but it contains information that may also be useful to you.
7-84
>>Print
Test Page ?
1
2
3
Press [OK] again. Processing appears and a test page is printed

out.
Press U or V repeatedly until >>Print Test Page appears.

Developer (Initializing the developer unit)

The replaced developer can be automatically fill up the toner using this
menu when a toner container is installed and the printer is turned on.
This is primarily used for maintenance by service personnel.
DRUM-CTRL (Setting the automatic drum surface refreshing)

The drum surface can be refreshed automatically at a predetermined
period of time using this menu, regardless of the status detected by the
temperature/humidity sensor. This is primarily used for maintenance by
service personnel.
Drum (Setting the drum refleshing mode)

This sets the refresh mode for the drum. When the printing quality
declines, refreshing the drum can restore the printing quality. This is
primarily used for maintenance by service personnel.
7-85
7-86
Options
This chapter explains the options for this printer.
General Information
Expansion Memory Modules
Paper Feeder (PF-310)
CompactFlash (CF) Card
Other Options
Options
8-2
8-4
8-6
8-6
8-7
8-9
8-1
General Information
The printers have the following options available to satisfy your printing
requirements. For instructions on installing individual options, refer to the
documentation included with the option. Some options are explained in
the following sections.
Note Install the memory module before installing the optional
paper feeder (PF-310).
FS-2020D/3920DN/4020DN
Envelope Feeder EF-310 (for

FS-3920DN/FS-4020DN)
Faceup Output Tray PT-310

(for FS-3920DN/FS-4020DN)
Expansion Memory (DIMM

64/128/256/512 MB)
Network Interface Card

IB-31 (for FS-2020D)
Hard Disk
HD-5A
CompactFlash
USB Flash Memory
Bulk Paper Feeder PF-315

(for FS-3920DN/FS-4020DN)
-2
Paper Feeder PF-310

FS-2020D x 1
FS-3920DN/FS-4020DN x 3
Options
Note Install the memory module before installing the optional

paper feeder (PF-430).
FS-6970DN
Faceup Output Tray

PT-430
Expansion Memory (DIMM

128/256/512 MB)
Hard Disk
HD-5A
CompactFlash
USB Flash Memory
Paper Feeder
PF-430 x 4
Options
8-3
Expansion Memory Modules

To expand the printer memory for more complex print jobs and faster
print speed, you can plug in optional memory module (dual in line
memory module) in the memory slot provided on the printer main
controller board. You can select additional memory module from 128,
256 or 512MB. The maximum memory size is 544MB.
Note The expansion memory should only be installed by your
service technician. We shall not be liable for any damages caused
by improper installation of expansion memory.
Precautions for handling the memory module

To protect electronic parts, discharge static electricity from your body by
touching a water pipe (faucet) or other large metal object before handling
the memory module. Or, wear an antistatic wrist strap, if possible, when
you install the memory module.
Always hold the main controller board or a memory module by its edges
as shown below to avoid damaging electronic parts.
Correct
8-4
Incorrect
Options
Installing the Memory Module

1
2
Turn off the printer and disconnect the power cord and printer cable.
Remove the screw and open the inner cover.
4
5
Remove the memory module from its package.
After you finish installing the memory module, secure the inner cover
with screws removed in step 3, and close the right cover.
Remove the right cover.
Aligning the cutouts of the memory module with the matching keys of
the socket, carefully plug the memory module into the memory
socket until it clicks in place. Then, push down the memory module
to secure.
Removing a Memory Module

To remove a memory module, remove the right cover and the memory
slot cover from the printer. Then, carefully push out the two socket
clamps. Ease the memory module out of the socket to remove.
Verifying the expanded memory

To verify that the memory module is working properly, test it by printing a
status page.
Options
8-5

The PF-310 paper feeder allows you to add three (FS-2020D: one) more
paper cassettes to the bottom of the printer for continuous feeding of a
large volume of paper. Each paper cassette can hold up to
approximately 500 sheets of ISO A4, ISO A5, JIS B5, letter, and legal
size (80g/m2) paper. This feeder is attached at the bottom of the printer
as shown on below.
FS-2020D
FS-3920DN/FS04020DN

The PF-430 paper feeder allows you to add four more paper cassettes to
the bottom of the printer for continuous feeding of a large volume of
paper. Each paper cassette can hold up to approximately 250 sheets of
ISO A4, ISO A5, JIS B5, letter, and legal size (80g/m2) paper. This
feeder is attached at the bottom of the printer as shown on below.
FS-6970DN
8-6
Options
CompactFlash (CF) Card

The printer is equipped with a slot for a CF card with the maximum size
of 256MB. A CF card is useful for storing fonts, macros, and overlays.
Turn off the printer and disconnect the power cord and printer cable.
CAUTION Before inserting a CF card in the printer, make

sure that the printer is switched off.
Options
Remove the screws and the option interface slot cover.
Install the CompactFlash card into the slot.
Secure the option interface slot cover with screws removed in step 2.
8-7
Faceup Output Tray (FS-3920DN/4020DN: PT-310; FS6970DN: PT-430)

Use the faceup output tray when you wish paper to be stacked with the
printed side facing up (reverse order).
To install the faceup output tray, perform the following procedures:
Install the paper stopper according to the size of paper to be used.
Install the faceup output tray on the rear of the printer.
IB-31 Network Interface Cards (For FS-2020D)

Along with the standard for the network interface on the printer, the
network interface card supports TCP/IP, IPX/SPX, NetBEUI and
AppleTalk protocols, so that the printer can be used on network
environments including Windows, Macintosh, UNIX, NetWare, etc. The
network interface card must be installed in the option interface slot. For
details, refer to IB-31 Installation Guide.
8-8
Options
Other Options
PF-315 Bulk Paper Feeder (for FS-3920DN/FS4020DN)
Holds approximately 2,000 sheets of 76 to 216 mm x 148 to 305 mm size
paper. This bulk paper feeder can be attached to the front of the printer
after the MP tray has been removed.
EF-310 Envelope Feeder (for FS-3920DN/FS-4020DN)

Holds more envelopes at a time than the MP tray. This envelope feeder
can be attached to the front of the printer after the MP tray has been
removed.
HD-5A Hard Disk

If a hard disk is installed in the printer, received data can be rasterized
and stored on this hard disk. This enables to use the Job Box functions.
For details, refer to Job Box on page 7-19.
USB Flash Memory

See your dealer for purchasing information of this optional device that
are best suited for use with this printer.
Options
8-9
8-10
Options
Computer Interface
This chapter contains explanations on the following topics:

General Information
Parallel Interface
USB Interface
Network Interface
Computer Interface
9-2
9-2
9-2
9-3
9-1
General Information
This chapter explains the connector specifications of parallel, USB, and
network interfaces.
Parallel Interface
The printer provides high-speed data transmission on a parallel
interface.
Note Use a parallel interface cable that complies with the IEEE
1284 standard.
USB Interface
This printer supports the Hi-Speed USB. USB (Universal Serial Bus)
interface specifications are as follows.
Specifications
Basic specification
Complies with the Universal Serial Bus Specification Revision 2.0.
Connectors
Printer: B-type receptacle (female) with upstream port
Cable: B-type plug (male)
Cable
Use a shielded cable that complies with USB 2.0 (Hi-Speed USB) and
not longer than 5 meters (16 feet).
Transfer Mode
High speed (480 Mbps maximum)
Full-Speed (12 Mbps maximum)
Power Control
Self-power device
Interface Signals
USB Connector Pin Assignment
9-2
Pin
Signal
Description
Vbus
Power supply (+5 V)
D-
Data transmission
D+
Data transmission
GND
Signal ground
Shell
Shield
Computer Interface
Network Interface
Features
Automatic IP address resolution
This feature is compatible with the DHCP/DHCPv6 protocol and allows
the printer to automatically receive IP addresses from the
DHCP/DHCPv6 server.
Management using Web browsers

HTTP pages are incorporated in to the interface, so that a web browser
can be used to monitor and change a range of settings. The settings can
be password-protected.
Support for a range of protocols

The SMTP, POP3, SSL, SNMP, IPv6 and Notables over TCP/IP
protocols are supported for easier printer management and more robust
security.
Support for IEEE 802.1x

The interface supports EAP-TLS and PEAP authentication.
Supports IPv6
Supports IPv6, which is based on IPv4 with improvements, such as
increased manageable address space, additional security functions and
priority based data transmission.
Supports IPSec
Supports IPSec, the security protocol that authenticates and encrypts in
the network layer (IP layer).
Specifications
Connector
10 Base-T/100 Base-TX
Operating Systems
Windows 2000/XP/Vista/Server2003, MacOS 10.x
Network protocols
IPv6: HTTP, LPD, FTP, IPP, RawPort, ICMPv6, LLTD, SNTP,

DHCPv6, SMTP, POP3, DNS, SNMPv1/v2c/v3, WSD
IPv4: HTTP, HTTPS, LPD, FTP, IPP, RawPort, ICMP, DHCP, SMTP,
POP3, SNTP, DNS, WINS, NetBIOS over TCP/IP, SNMPv1/v2c/v3,
Apple Bonjour Compatible, IPPS, LLTD, WSD
Etc.: IPX/SPX, NetWare (NDS/Bindery), AppleTalk, NetBEUI
Security Protocols
SSL/TLS (HTTPS, IPPS), SNMPv3, EAP-TLS, PEAP, AH, ESP
Operation Environment
10 to 35 C (50 to 95 F), 20-80% RH (condensation-free)
Computer Interface
9-3
EMI Countermeasures
VCCI Class B, FCC Class B (U.S.), CE (Europe)
IMPORTANT When IPv6 functions are used, the devices used on the
network (routers, PCs, etc) must support IPv6.
9-4
Computer Interface
10 Appendix
This section lists the following information of this printer.
Specifications
Environmental Standard Requirements
Appendix
10-2
10-4
10-1
Specifications
Note These specifications are subject to change without notice.
Description
Item
FS-2020D
FS-3920DN
FS-4020DN
FS-6970DN
Type
Desktop
Printing Method
Semiconductor laser and electrophotography
Paper
Weight
Cassette
60 to 120 g/m
MP Tray
60 to 220 g/m
Paper
Type
Cassette
Plain, Preprinted, Bond, Recycled, Rough, Letterhead, Color (Colour), Prepunched, High
Quality, and Custom (1 to 8)
MP
Plain, Transparency, Preprinted, Labels, Bond, Recycled, Rough, Vellum, Letterhead, Color
Tray/Manu (Colour), Prepunched, Envelope, Cardstock, Thick paper, High Quality, and Custom (1 to 8)
al Feed
Paper
Size
Cassette
A4, A5, JIS B5,

Letter, Legal, Folio,
Oficio II, Statement,
ISO B5, Envelope
C5, Executive, 16 kai,
Custom (140 210 to
216 356mm)
MP Tray
A4, JIS B5, A5, Folio, Legal, Letter, Oficio II, Statement, Executive,
A6, JIS B6, ISO B5, Envelope C5, Envelope #10, Envelope #9,
Envelope #6, Envelope Monarch, Envelope DL, Hagaki, OfukuHagaki, 16K, Yokei 2, Yokei 4, Custom (70 148 to 216 356mm)
A4, A5, JIS B5, A6, Letter, Legal, Folio, Oficio

II, Statement, ISO B5, Envelope C5,
Executive, 16 kai, Custom (105 148 to 216
356mm)
Ledger, Legal, Letter, A3,

A4, B4, A5, JIS B5, A5,
A6, Folio, Oficio II,
Statement, Envelope C4,
Envelope C5, ISO B5,
Executive, 8 kai, 16 kai,
Custom (148 210 to
297 432mm
Ledger, Legal, Letter, A3,
A4, B4, A5, JIS B5, A5,
A6, Folio, Oficio II,
Envelope Monarch,
Envelope #10, Envelope
DL, Statement, Envelope
C4, Envelope C5, ISO
B5, Executive, Envelope
#9, Envelope #6, Hagaki,
Ofuku-Hagaki, 8 kai, 16
kai, Yokei 2, Yokei 4,
Custom (70 148 to 297
450mm)
Magnification ratio
25 to 400%, 1% increments
Printing
Speed
A6: 21 ppm*
A6: 22 ppm
A6: 23 ppm
A4: 35 ppm
A5: 21 ppm
A5: 22 ppm
A5: 23 ppm
A5: 35 ppm
A4: 35 ppm
A4: 40 ppm
A4: 45 ppm
A3: 17 ppm
Letter: 37 ppm
Letter: 42 ppm
Letter: 47 ppm
Legal: 28 ppm
Legal: 33 ppm
Legal: 38 ppm
A4: 17.5 ppm
A4: 24.5 ppm
A4: 32.5 ppm
A4: 24.5 ppm
Letter: 18.5 ppm
Letter: 26 ppm
Letter: 34 ppm
A5-R: 16 ppm
Simplex
Duplex
A3: 10.5 ppm
10-2
Appendix
Description
Item
FS-2020D
FS-3920DN
FS-4020DN
FS-6970DN
First Print Time (A4,

feed from Cassette)
9 seconds or less
10.5 seconds or less
9 seconds or less when

EcoFuser is Off and the
printer is in Ready status.
24 seconds or less when
EcoFuser is On or the
printer is in sleep mode
Warm-up Power on
Time
Sleep
(22C/71.6
F,
60%RH)
17 seconds or less
17 seconds or less
17 seconds or less
15 seconds or less
15 seconds or less
15 seconds or less
15 seconds or less
Paper
Capacity
Cassette
500 sheets (80 g/m)
250 sheets (80 g/m)
MP Tray
100 sheets (80 g/m)
100 sheets (80 g/m)
Top Tray
250 sheets (80 g/m)
500 sheets (80 g/m)
Face-up
Tray
PT-310: 250 sheets (80 g/m)
Output
Tray
Capacity
250 sheets (80 g/m)
Continuous printing
1 to 999 sheets
Resolution
Fine 1200 mode, Fast 1200 mode, 600 dpi, 300 dpi
Operating
Environment
Temperature
10 to 32.5C/50 to 90.5F
Humidity
15 to 80 %
Altitude
2,500 m/8,202 ft maximum
Brightness 1,500 lux maximum

Controller
PowerPC 440/533
MHz
Supported OS
Windows 2000 Service Pack 2 or later, Windows Server 2003, Windows XP, Windows Vista,
Mac OS X 10.x
Interface
Standard
Parallel: 1
(IEEE1284)
Hi-Speed USB: 1
Full-speed USB: 1
(USB flash memory
slot)
KUIO/W slot
Option
IB-31: 10/100BASETX
PowerPC 440/600
MHz
PowerPC 440/667
MHz
Parallel: 1 (IEEE1284)
Hi-Speed USB: 1
Network: 1(10BASE-T/100BASE-TX)
Full-speed USB: 1 (USB flash memory slot)
KUIO/W slot
PDL
PRESCRIBE
Emulation
PCL 6, KPDL, KPDL (AUTO), Line Printer, IBM Proprinter, DIABLO

630, EPSON LQ-850
Memory
Standard
PowerPC 440/600 MHz
PCL 6, KPDL, KPDL

(AUTO), Line Printer, IBM
Proprinter, DIABLO 630,
EPSON LQ-850, KC-GL
128MB
Maximum 1152MB
Appendix
10-3
Description
Item
FS-2020D
FS-3920DN
FS-4020DN
FS-6970DN
Dimension (W x D x H) 382 394 285 mm 382 394 320 mm

15 1/16 15 1/2 11 15 1/16 15 1/2 12 5/8"
1/4"
469 395 285 mm

18 1/2 15 9/16 11 1/4"
Weight (without toner

container)
16.2 kg/35.7 lb
19.5 kg/43 lb
Power Requirements
120 V AC, 60 Hz, 7.6 120 V AC, 60 Hz, 7.7 120 V AC, 60 Hz,
A/ 220 to 240 V AC, A/ 220 to 240 V AC, 7.7 A/ 220 to 240 V
50/60 Hz, 4.1 A
50/60 Hz, 4.2 A
AC,
16.8 kg/37 lb
220 to 240 V AC, 50/60

Hz, 3.9 A
50/60 Hz, 4.3 A

Power
Maximum 947 W
Consumpti
(U.S.A./Canada),
on
1004 W (European
countries)
964 W
(U.S.A./Canada),
1022 W (European
countries)
970 W
(U.S.A./Canada),
1029 W (European
countries)
During
printing
543 W
(U.S.A./Canada), 560
W (European
countries)
658 W
W (European
countries)
682 W
516 W
W (European
countries)
During
standby
9.1 W
(U.S.A./Canada), 9.2
W (European
countries) when
EcoFuser is On.
9.4 W
W (European
countries) when
EcoFuser is On.
9.4 W
W (European
countries) when
EcoFuser is On.
9.6 W when EcoFuser is

On
69 W
(U.S.A./Canada), 68
W (European
countries) when
EcoFuser is Off.
76 W when EcoFuser 80 W
is Off.
(U.S.A./Canada), 79
W (European
countries) when
EcoFuser is Off.
67 W when EcoFuser is
Off.
5.5 W
(U.S.A./Canada),
5.7 W (European
countries)
5.5 W
(U.S.A./Canada),
5.9 W (European
countries)
Sleep
mode
Power off 0 W
Options
*.
976 W
Expanded memory,
Paper Feeder (500sheet x 1), Hard disk
(HD-5A)
6.3 W
(U.S.A./Canada),
6.4 W (European
countries)
0W
Expanded memory, Paper Feeder (500-sheet Expanded memory,
x 3), Hard disk (HD-5A)
Paper Feeder (250-sheet
x 4), Hard disk (HD-5A)
Only applicable to feeding from MP tray.
Environmental Standard Requirements

This machine conforms to the following environmental standard
requirements.
Time for switching to Sleep mode (default):

15 minutes (FS-2020D/3920DN/4020DN)/5 minutes (FS-6970DN)
Duplex Printing: Standard Equipment
Durable paper for feeding: Paper made of 100% recycled paper
Note Contact your Dealer or Service Representative for
recommended paper types.
10-4
Appendix
Glossary
Additional memory
An additional memory (optional) is used for increasing the memory
capacity of this machine. For DIMM that can be used in this machine,
contact your service technician.
AppleTalk
AppleTalk offers file sharing and printer sharing and it also enables you
to utilize application software that is on another computer on the same
AppleTalk network.
Default Gateway
This indicates the device, such as a computer or router, that serves as
the entrance/exit (gateway) for accessing computers outside of the
network that you are on. When no specific gateway is designated for a
destination IP address, data is sent to the host that is designated as the
Default Gateway.
DHCP (Dynamic Host Configuration Protocol)

This is a protocol that automatically resolves the IP address, Subnet
Mask and Gateway address on a TCP/IP network. Use of DHCP
minimizes the load of network administration, especially on network
environments with a large number of client computers where it is not
specifically necessary to assign a separate IP address to each client,
including printers.
dpi (dots per inch)

This indicates the number of dots printed per inch (25.4mm) as a unit for
expressing resolution.
EcoPrint
This is a printing mode that reduces toner consumption. Pages printed in
the EcoPrint mode are lighter than pages printed in the normal mode.
Emulation
This refers to emulation of other manufacturers' printers. The printer
emulates operation of the following printers: PCL 6, KPDL, KPDL
(AUTO), Line Printer, IBM Proprinter, DIABLO 630 and EPSON LQ-850.
Form Feed Timeout

While data is being sent to a printer, some pauses may occur. At this
time, the printer waits for the next data without making a page break.
Form feed timeout is a function to wait only a preset amount of time
before it executes an automatic page break. After the waiting period
begins, once the designated amount of time is exceeded, the printer will
automatically process the currently received data and print it out. If the
machine has received no print data for the last page, the printer ends
processing of that job without outputting paper.
11-1
IEEE1284
This is a standard used when connecting a printer to a computer, and
was established by the Institute of Electrical and Electronic Engineers in
1994.
IP Address (Internet Protocol Address)

The Internet Protocol address is a unique number that represents a
specific computer in a network. The format of an IP Address is four
numbers separated by dots, e.g. 192.168.110.171. Each number should
be a decimal between 0 and 255.
KPDL
KPDL is Kyocera's implementation of the PostScript page description
language Level3.
MP tray
This tray is used instead of the cassette when printing on envelopes,
postcards, transparency sheets, and labels.
NetBEUI (NetBIOS Extended User Interface)

An enhanced version of the NetBIOS protocol, it enables the utilization
of more advanced functions on small-scale networks than do other
protocols such as TCP/IP, etc.
Outline font
With outline fonts, character outlines are represented with numerical
expressions and fonts can be enlarged or reduced in different ways by
changing the numeric values of those expressions. Printing remains
clear even if you enlarge fonts, since the characters are defined with
outlines represented with numerical expressions. You can specify the
font size in steps of 0.25 points up to 999.75 points.
Parallel interface
With this interface, data transfer between the printer and the computer
takes place in 8-bit chunks. The printer can perform IEEE1284
compatible bi-directional communications.
PostScript
This is a page description language developed by Adobe Systems, Inc. It
enables flexible font functions and highly-functional graphics, allowing
higher quality printing.
PPM (prints per minute)

This indicates the number of printouts made in one minute.
Printer driver
The printer driver makes it possible for you to print data created using
application software. The printer driver for the printer is contained on the
CD-ROM supplied with the printer. Install the printer driver on the
computer connected to the printer.
11-2
Sleep mode
This mode is provided to save power. It is activated when the machine is
not used for a preset period of time. In this mode, power is reduced to
the minimum. The default setting can be changed.
Status page
This lists machine conditions, such as the machine's memory, the total
number of prints and paper source settings. You can print the status
page from the operation panel.
Subnet Mask
This is a 32-bit numerical value that defines which bits of the IP address
specify the network address and which specify the host address.
TCP/IP (Transmission Control Protocol/Internet Protocol)

TCP/IP is a suite of protocols designed to define the way computers and
other devices communicate with each other over a network.
USB (Universal Serial Bus)

An interface standard for low to middle speed serial interfaces. This
printer supports Hi-Speed USB. The maximum transfer rate is 480 Mbps
and the maximum cable length is 5 meters (16 feet).
11-3
11-4
Index
Numerics
3D view
status monitor .........................................................4-20
3DES setting
SSL server ..............................................................7-73
A
Accessing the status monitor ......................................... 4-20
Additional memory .........................................................11-1
Adhesive label ................................................................. 2-9
Administrator ID .......................................... 7-67, 7-75, 7-81
Change ................................................................... 7-82
Administrator Password .............................. 7-68, 7-76, 7-81
Change ................................................................... 7-82
AES setting
SSL server ..............................................................7-73
Alarm (Buzzer) ............................................................... 7-56
Alternative emulation for KPDL ...................................... 7-39
Appearance tab
status monitor setting .............................................4-23
AppleTalk .......................................................................7-71
Automatic Cassette Selection ........................................7-36
B
Bulk paper feeder
clearing paper jams ................................................6-18
C
Cancel key
operation panel ......................................................... 1-4
Document processor ................................................6-3

Clearing paper jams
bulk paper feeder ....................................................6-18
duplexer ..................................................................6-16
envelope feeder ......................................................6-18
inside the printer .....................................................6-17
MP tray ...................................................................6-14
paper cassette ........................................................6-15
paper feeder ...........................................................6-15
rear unit ..................................................................6-18
Code set
Setting ....................................................................7-43
Common device
Selecting or setting .................................................7-55
CompactFlash card ..........................................................8-7
Components
at the front of the printer ...........................................1-2
at the left of the printer and internal ..........................1-2
at the rear of the printer ............................................1-3
Connection
network cable ...........................................................4-2
parallel cable .............................................................4-2
power cord ................................................................4-3
USB cable .................................................................4-2
Counter
Printed pages ..........................................................7-25
Cursor keys
operation panel .........................................................1-4
Custom mode
installation method ..................................................4-15
D
DES setting
SSL server ..............................................................7-72
DIMM ........................................................................8-2, 8-3
Canceling a Printing Job ..................................................7-6
dpi ..................................................................................11-1
Carriage return code ......................................................7-49
Duplex path
Setting ....................................................................7-34
Cassette
Basis weight .............................................................2-5
loading paper ............................................................ 3-2
Paper size ............................................................... 7-29
Paper type ..............................................................7-32
CF card ............................................................................ 8-7
option .................................................................8-2, 8-3
Changing default font size .............................................7-42
Changing network interface parameters .......................... 4-4
Character pitch ..............................................................7-43
Cleaning
printer ....................................................................... 5-7
Duplex Printing ..............................................................7-37

Binding modes ........................................................7-37
Error detection ........................................................7-62
Duplexer
E
Emulation
on the status page ..................................................7-14
Setting ....................................................................7-38
Envelope feeder
Index-1
clearing paper jams .................................................6-18
SSL server ............................................................. 7-73
Environmental standard requirements ...........................10-4
IPSec (IP Security Protocol) .......................................... 7-74
Error Detection
Duplex printing ........................................................7-62
Paper mismatch ......................................................7-62
Setting .....................................................................7-61
J
Job Accounting .............................................................. 7-76
Error messages
of hard disk .............................................................6-10
of memory card .......................................................6-10
of RAM disk .............................................................6-11
tabled, with corrective actions ...................................6-5
Job Box ......................................................................... 7-19

Configuration .......................................................... 7-24
Private Print/Stored Job ......................................... 7-23
Proof-and-Hold ....................................................... 7-21
Quick Copy ............................................................ 7-20
Exiting the status monitor ...............................................4-20
Job Retention ................................................................ 7-19
Expansion memory module

option ................................................................ 8-2, 8-3
Job Storage ................................................................... 7-20
Express mode
installation method ..................................................4-14
F
First container
toner container ..........................................................5-2
Font select
Selecting default font ..............................................7-41
Keys
Basic operation ........................................................ 7-6
Cancel ...................................................................... 7-6
Cursor keys .............................................................. 7-7
GO ........................................................................... 7-6
MENU ...................................................................... 7-6
OK ............................................................................ 7-7
KPDL Errors .................................................................. 7-40
General problems
troubleshooting .........................................................6-2
Label ............................................................................... 2-8
GO key
operation panel .........................................................1-4
Left cover
components ............................................................. 1-2
Linefeed code ................................................................ 7-49
Hard disk ................................................................ 7-59, 8-9
Loading paper
cassette .................................................................... 3-2
MP tray ..................................................................... 3-6
HTTPS setting
SSL server ..............................................................7-74
Loading thick paper and envelopes

MP tray ..................................................................... 3-8
Indicators
operation panel .........................................................1-4
Machine parts .................................................................. 1-1
Inside the printer

Installation method
custom mode ..........................................................4-15
express mode .........................................................4-14
Maintenance
Toner container replacement, cleaning .................... 5-1
Memory
Installing ................................................................... 8-5
on the status page .................................................. 7-14
Installing CF card .............................................................8-7
Memory card
Using CF card ........................................................ 7-60
Installing memory module ................................................8-5
Memory module handling ................................................ 8-4
Installing the printer driver ..............................................4-13

Mac OS ...................................................................4-16
Windows PC ...........................................................4-13
MENU key
operation panel ........................................................ 1-4
IPP (Internet Printing Protocol) ......................................7-71
Menu Selection System .................................................. 7-8
IPP over SSL setting
Message Display
Index-2
Menu Map sample ......................................................... 7-12
Indicators .................................................................. 7-5

Status information .....................................................7-4
Operation Panel
diagram .....................................................................7-3
Message display
Online help messages ............................................ 6-13
operation panel ......................................................... 1-4
Operation panel
components ..............................................................1-2
indicators, keys .........................................................1-4
Message Language ....................................................... 7-55
Option
Bulk paper feeder .....................................................8-2
CompactFlash ....................................................8-2, 8-3
Document finisher .....................................................5-7
Envelope feeder .......................................................8-2
expansion memory module ................................8-2, 8-3
Faceup output tray .............................................8-2, 8-3
Hard disk ...........................................................8-2, 8-3
Network interface card ..............................................8-2
Paper feeder ......................................................8-2, 8-3
paper feeder .............................................................8-2
USB flash memory .............................................8-2, 8-3
Mode Selection Menu ...................................................... 7-8

Moving printer .................................................................. 5-8
MP tray .......................................................................... 11-2
Basis weight .............................................................2-5
components .............................................................. 1-2
loading envelopes .....................................................3-8
loading paper ............................................................ 3-6
loading thick paper ................................................... 3-8
minimum and maximum paper sizes ........................ 2-3
Paper size ............................................................... 7-27
Paper type .....................................................2-12, 7-28
N
Names
Operation panel ........................................................1-4
Option interface slot

components ..............................................................1-3
Original platen
Cleaning ...................................................................6-2
Other paper properties .....................................................2-7
Outline font ....................................................................11-2
NetWare .........................................................................7-70
Override A4/Letter .........................................................7-38
NetWare, AppleTalk, IPP and SSL Server settings

Network interface parameters .................................. 4-6
Network
TCP/IP (IPv4) .........................................................7-50
TCP/IP (IPv6) .........................................................7-53
Network cable
connection ................................................................4-2
Network indicators
components .............................................................. 1-3
Network Interface .............................................................9-3
Setting Network interface card (NIC) ...................... 7-69
Network interface connector
components .............................................................. 1-3
Network interface parameters
AppleTalk ............................................... 4-9, 4-10, 4-11
IPP ............................................................................ 4-9
NetWare .................................................................... 4-8
SSL Server ............................................................. 4-10
TCP/IP ......................................................................4-5
TCP/IP (IPv6) ...........................................................4-6
Network interface status page
printing ....................................................................4-12
Number of copies
USB flash memory .................................................. 7-18
O
OK key
operation panel ......................................................... 1-4
Online help messages
for clearing paper jams ........................................... 6-13
Page Set
Carriage-return .......................................................7-49
Linefeed ..................................................................7-49
Number of copies ...................................................7-46
Print orientation .......................................................7-48
Setting ....................................................................7-46
Wide A4 pitch .........................................................7-49
Paper
Availability .................................................................2-2
Colored ...................................................................2-11
composition ..............................................................2-4
Condition ..................................................................2-4
Envelope .................................................................2-10
Guidelines .................................................................2-4
Minimum and maximum sizes ..................................2-3
Moisture content .......................................................2-6
Postcard ...................................................................2-9
Preprinted ...............................................................2-11
Recycled .................................................................2-11
smoothness ..............................................................2-5
Thick .......................................................................2-10
thickness ...................................................................2-6
Transparency ............................................................2-8
Paper cassette
components ..............................................................1-2
minimum and maximum page sizes .........................2-3
Paper type ..............................................................2-12
Paper Feed Source ........................................................7-35
Paper feeder ....................................................................8-6
Index-3

option ........................................................................8-2
Paper grain .......................................................................2-7
Paper Size
Custom ....................................................................7-30
Printing KPDL error report ............................................. 7-40

Prolonged non-use .......................................................... 5-8
Paper sizes ......................................................................2-4
RAM Disk ...................................................................... 7-58
Paper specifications .........................................................2-2
Rear unit
clearing paper jams ................................................ 6-18
components ............................................................. 1-3
Paper stopper
components ..............................................................1-2
Paper Type
Custom ....................................................................7-33
Paper weight ....................................................................2-6
Parallel cable
connection .................................................................4-2
Parallel interface
Setting parallel interface .........................................7-69
Parallel interface connector
components ..............................................................1-3
PF-310 ..................................................................... 8-2, 8-6
Removing memory module ............................................. 8-5

Removing USB flash memory ....................................... 7-18
Replacement
toner container .................................................. 5-2, 5-3
waste toner box ........................................................ 5-5
Replacing toner container ............................................... 5-3
Replacing waste toner box .............................................. 5-5
Resetting custom paper type ........................................ 7-34
Restart Printer ............................................................... 7-83
PF-430 .............................................................................8-6
Right cover
components ............................................................. 1-2
Pop-up window
status monitor .........................................................4-20
Possible paper jam locations .........................................6-12

Power cord
connection .................................................................4-3
Power cord connector
components ..............................................................1-3
Power switch
components ..............................................................1-2
Print
Fonts list ..................................................................7-15
Hard disk file list ......................................................7-15
Job Accounting List .................................................7-80
Memory card file list ................................................7-16
Menu map ...............................................................7-11
Network Status Page ..............................................7-84
RAM disk file list ......................................................7-15
Status page ................................................... 7-13, 7-84
Print file
USB flash memory ..................................................7-17
Print Quality
EcoPrint mode ........................................................7-45
KIR mode ................................................................7-44
Print density ............................................................7-45
Setting .....................................................................7-44
Print quality problems
troubleshooting .........................................................6-3
Print restriction selection ................................................7-77
Printing a list of files
USB flash memory ..................................................7-18
Screen overview
pop-up window,3D view,status monitor icon .......... 4-20
Security level ................................................................. 7-74
Selecting paper feed source
USB flash memory ................................................. 7-18
Selecting regular or dark ............................................... 7-41
Service (for maintenance) ............................................. 7-84
Size dial ......................................................................... 7-30
Sleep mode ................................................................... 11-3
Sound notification tab
status monitor setting ............................................. 4-22
Special paper .................................................................. 2-8
Specifications ................................................................ 10-2
Environmental specifications ................................. 10-4
Network interface ..................................................... 9-3
USB interface ........................................................... 9-2
SSL (Secure Sockets Layer) Server ............................. 7-72
Status monitor
3D view .................................................................. 4-20
access .................................................................... 4-20
exit ......................................................................... 4-20
pop-up window ....................................................... 4-20
status monitor icon ................................................. 4-21
Status monitor icon
status monitor ........................................................ 4-21
Printing a network interface status page ........................4-12
Status monitor settings

sound notification tab,appearance tab ................... 4-22
Printing from application software ..................................4-19
Status page sample ...................................................... 7-13
Index-4
Storage error codes

hard disk,memory card,USB flash memory ............6-10
Waste toner box

components ..............................................................1-2
TCP/IP, TCP/IP (IPv6) settings

network interface parameters ................................... 4-4
Timer
Auto error clear ....................................................... 7-65
Auto panel reset ..................................................... 7-66
Auto sleep ............................................................... 7-66
Automatic form feed timeout ................................... 7-63
Error clear time ....................................................... 7-65
Panel reset ............................................................. 7-66
Sleep ......................................................................7-64
Tips .................................................................................. 6-2
Toner container
components .............................................................. 1-2
how to replace ..........................................................5-3
replacement .............................................................. 5-2
Toner kit
toner container, plastic waste bag, waste toner box,installation guide ................................................. 5-2
Top cover
components .............................................................. 1-2
Top tray
components .............................................................. 1-2
Transparency ...................................................................2-8
Troubleshooting ............................................................... 6-1
general problems ...................................................... 6-2
print quality problems ...............................................6-3
Turning on the power ....................................................... 4-3
U
Uninstalling software ......................................................4-24
Unit of measurement
Selecting .................................................................7-31
USB cable
connection ................................................................4-2
USB Interface .................................................................. 9-2
USB interface .................................................................7-69
USB interface connector
components .............................................................. 1-3
USB Memory .................................................................7-17
USB memory slot ...........................................................7-68
components .............................................................. 1-2
V
Verifying expanded memory ............................................8-5
Viewing counter value .................................................... 7-25
Index-5
Index-6
<Memo>
<Memo>
We recommend the use of our own brand supplies.

We will not be liable for any damage caused by the use of third party supplies in this machine.
E1
452+%9
First Edition 2009.05

FS-1100 FS-1300D: FS-2020D/FS-3920DN/FS-4020DN/ FS-6970DN

Uploaded by

Copyright:

Available Formats

FS-1100 FS-1300D: FS-2020D/FS-3920DN/FS-4020DN/ FS-6970DN

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FS-1100 FS-1300D: FS-2020D/FS-3920DN/FS-4020DN/ FS-6970DN

Uploaded by

Copyright:

Available Formats

OPERATION GUIDE

This Operation Guide is for models FS-2020D, FS-3920DN, FS-4020DN

Operation Guide (This Guide)

Advanced Operation Guide

Machine Parts ..................................................................... 1-1

Paper Handling ................................................................... 2-1

Loading Paper .................................................................... 3-1

Connecting and Printing .................................................... 4-1

Maintenance ........................................................................ 5-1

Troubleshooting ................................................................. 6-1

Using the Operation Panel ................................................. 7-1

Options ................................................................................ 8-1

Paper Feeder (PF-310) ....................................................... 8-6

Computer Interface ............................................................. 9-1

10 Appendix ........................................................................... 10-1

Legal and Safety

1. the equivalent of U.S. $25,000 in your local currency; or

Typeface Trademark Acknowledgement

Monotype Imaging License Agreement

3. To protect proprietary rights of Monotype Imaging, you agree to

Open SSLeay License

Redistributions of source code must retain the above copyright

Redistributions in binary form must reproduce the above copyright

All advertising materials mentioning features or use of this software

The names "OpenSSL Toolkit" and "OpenSSL Project" must not be

Products derived from this software may not be called "OpenSSL"

Redistributions of any form whatsoever must retain the following

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS"

Original SSLeay License

Redistributions of source code must retain the copyright notice, this

Redistributions in binary form must reproduce the above copyright

All advertising materials mentioning features or use of this software

If you include any Windows specific code (or a derivative thereof)

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY

Compliance and Conformity

Reorient or relocate the receiving antenna.

CAUTION The changes or modifications not expressly approved by

IMPORTANT Be sure to power off the printer before connecting or

DANGER CLASS 3B LASER RADIATION WHEN OPEN.

Radio Frequency Transmitter

Radio Tag Technology

For Europe, Asia, and

For U.S.A. and

Safety Instructions Regarding the

Declaration of Conformity (Australia)

Kyocera Mita Australia Pty., Ltd.

Canadian Department of Communications

Avis de conformit aux normes du ministere

Energy Saving Function

Energy Star (ENERGY STAR) Program

[Always connect the machine to an outlet with a ground

Please contact your service representative to order a replacement if the

Avoid placing the machine on or in locations which are unstable

* 15-3/4" (400mm) FS-3920DN/FS-4020DN: PT-310

Avoid locations near a window or with exposure to direct sunlight.

Power Supply/Grounding the Machine

Handling of plastic bags

Precautions for Use

If dust accumulates within the machine, there is a danger of fire or