MATERIAL SAFETY DATA SHEET

DAUBERT CHEMICAL COMPANY

4700 SOUTH CENTRAL AVENUE
CHICAGO, ILLINOIS 60638
TELEPHONE: (708) 496-7350
FAX: (708) 496-7357

EMERGENCY CONTACT:
CHEMTREC: (800) 424-9300

HMIS HAZARD RATING

HEALTH

FIRE

REACTIVITY

PERSONAL PROTECTION

Date of Review: March 24, 2008

Date of Preparation: July 23, 2003

Revised: May 23, 2012

By: R. Lauterbach

SECTION I: PRODUCT IDENTIFICATION

Product Name:
Chemical Family:

Tectyl 502C Class I (MIL-PRF-16173 Class 1 Grade 2)

Petroleum Based Rust Preventative

SECTION II: HAZARDS IDENTIFICATION

Eye: Can cause eye irritation. Symptoms include stinging, tearing, redness and swelling of eyes.
Skin: Can cause skin irritation. Prolonged or repeated contact may dry the skin. Symptoms may include redness,
burning, drying and cracking of skin, burns and other skin damage. Additional symptoms of skin contact may
include: allergic skin reaction (delayed skin rash which may be followed by blistering, scaling and other skin
effects).
Swallowing: Swallowing small amounts of this material during normal handling is not likely to cause harmful
effects. Swallowing large amounts may be harmful. This material can enter the lungs during swallowing or vomiting
and cause lung inflammation and/or damage.
Inhalation: Breathing of vapor or mist is possible. Breathing small amounts of this material during normal handling
is not likely to cause harmful effects. Breathing large amounts may be harmful.
Symptoms of Exposure: Stomach or intestinal upset (nausea, vomiting, diarrhea), irritation (nose, throat, airways),
central nervous system depression (dizziness, drowsiness, weakness, fatigue, nausea, headache, unconsciousness),
and death.
Target Organ Effects: Overexposure to this material (or its components) has been suggested as a cause of the
following effects in humans and may aggravate pre-existing disorders of these organs: Central nervous system
effects.
Developmental Information: No Data.
Cancer Information: No Data.
Other Health Effects: No Data.
Primary Route(s) of Entry: Inhalation, skin contact.

SECTION III: COMPOSITION/INFORMATION ON INGREDIENTS

Component
Aliphatic Hydrocarbons
(Stoddard Type)
CAS #8052-41-3

Tectyl 502C Class I [3114]

Wt%
32-42

Recommended Exposure Limits (TWA)

OSHA PEL: 100 ppm
ACGIH TLV: 100 ppm

5/23/12

Page 1 of 4

Component
Zinc Soap
CAS #68918-69-4

Wt%
20-30

Recommended Exposure Limits (TWA)

OSHA PEL: None Established
ACGIH TLV: None Established

Petrolatum
CAS #8009-03-8

5-15

OSHA PEL: None Established

ACGIH TLV: None Established

Hydrotreated Heavy
Naphthenic Distillate
CAS #64742-52-5

10-20

OSHA PEL: 5 mg/m3

ACGIH TLV: 5 mg/m3

Petroleum Sulfonate
CAS #78330-12-8

6-11

OSHA PEL: None Established

ACGIH TLV: None Established

SECTION IV: FIRST AID MEASURES

Eyes: If symptoms develop, move individual away from exposure and into fresh air. Flush eyes gently with water
while holding eyelids apart. If symptoms persist or there is any visual difficulty, seek medical attention.
Skin: Remove contaminated clothing. Wash exposed area with soap and water. If symptoms persist, seek medical
attention. Launder clothing before reuse.
Swallowing: DO NOT INDUCE VOMITING. This material is an aspiration hazard. If individual is drowsy or
unconscious, place on left side with the head down. Seek medical attention. If possible, do not leave individual
unattended.
Inhalation: If symptoms develop, immediately move individual away from exposure and into fresh air. Seek
immediate medical attention; keep person warm and quiet. If person is not breathing, begin artificial respiration. If
breathing is difficult, administer oxygen.
Note to Physicians: No Data.

SECTION V: FIRE FIGHTING MEASURES

Flash Point:
106 oF (41.1 oC) PMCC
Explosive Limit: (for component) Lower 1.0
Upper 6.0%
Auto ignition Temperature:
No Data.
Hazardous Products of Combustion: May form carbon dioxide and carbon monoxide, sulfur compounds, various
hydrocarbons.
Fire and Explosion Hazards: Vapors are heavier than air and may travel along the ground or be moved by
ventilation and ignited by heat, pilot lights, other flames and ignition sources at locations distant from material
handling point. Never use welding or cutting torch on or near drum (even empty) because product (even just residue)
can ignite explosively.
Extinguishing media: regular foam, carbon dioxide, dry chemical.
Fire Fighting Instructions: Water may be used to keep fire-exposed containers cool until fire is out. Wear a selfcontained breathing apparatus with a full face piece operated in the positive pressure demand mode with appropriate
turn-out gear and chemical resistant personal protective equipment. Refer to the personal protective equipment
section of this MSDS.

SECTION VI: ACCIDENTAL RELEASE MEASURES

Small Spills: Absorb liquid on vermiculite, floor absorbent or other absorbent material.
Large Spill: Eliminate all ignition sources (flares, flames including pilot lights, electrical sparks). Persons not
wearing protective equipment should be excluded from area of spill until clean-up has been completed. Stop spill at
source. Pump or vacuum transfer spilled product to clean containers for recovery. Absorb unrecoverable product.
Transfer contaminated absorbent, soil and other materials to containers for disposal. Prevent from entering drains,
sewers, streams or other bodies of water. Prevent from spreading. If runoff occurs, notify authorities as required.

Tectyl 502C Class I [3114]

5/23/12

Page 2 of 4

SECTION VII: HANDLING AND STORAGE

Handling: Containers of this material may be hazardous when emptied. Since emptied containers retain product
residues (vapor, liquid, and/or solid), all hazard precautions given in the data sheet must be observed. All five gallon
pails and larger metal containers including tank cars and tank trucks should be grounded and/or bonded when
material is transferred.
Storage: Not Applicable.

SECTION VIII: EXPOSURE CONTROLS/PERSONAL PROTECTION

Eye Protection: Chemical splash goggles in compliance with OSHA regulations are advised; however, OSHA
regulations also permit other type safety glasses. Consult your safety representative.
Skin Protection: Wear resistant gloves such as, neoprene, nitrile rubber. Wear normal work clothing covering
arms and legs.
Respiratory Protections: If workplace exposure limit(s) of product or any component is exceeded, a
NIOSH/MSHA approved air supplied respirator is advised in absence of proper environmental control. OSHA
regulations also permit other NIOSH/MSHA respirators (negative pressure type) under specified conditions (consult
your industrial hygienist). Engineering or administrative controls should be implemented to reduce exposure.
Engineering Controls: Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain
exposure below TLVs).

SECTION IX: PHYSICAL AND CHEMICAL PROPERTIES

Boiling Point:
Vapor Pressure:
Specific Vapor Density:
Specific Gravity:
Liquid Density:
Percent Volatiles (including water):
VOCs:
Evaporation Rate:
Appearance:
State:
Physical Form:
Color:
Odor:
pH:

315 oF (157.2 OC)

2 mmHg
>1.000 @ AIR=1
.88 @ 77 oF
7.16 lbs/gal @ 77 oF (.88 kg/l @ 25 oC)
40 %
2.9 lbs/gal
Slower than ethyl ether
Translucent
Liquid
No Data
Amber
No Data
No Data

SECTION X: STABILITY AND REACTIVITY

Hazardous Polymerization: Product will not undergo hazardous polymerization.
Hazardous Decomposition: May form: carbon dioxide and carbon monoxide, sulfur compounds, various
hydrocarbons.
Chemical Stability: Stable
Incompatibility: Avoid contact with strong oxidizing agents.

SECTION XI: TOXICOLOGICAL INFORMATION

None known

SECTION XII: ECOLOGICAL INFORMATION

None known

Tectyl 502C Class I [3114]

5/23/12

Page 3 of 4

SECTION XIII: DISPOSAL CONSIDERATION

Waste Management Information: Dispose of in accordance with all applicable local, state and federal regulations.

SECTION XIV: TRANSPORT INFORMATION

DOT Information 49 CFR 172.101
DOT Description:
Container/Mode:
NOS Component:
RQ (Reportable Quantity) 49 CFR 172.101:

Combustible liquid, N.O.S., III

Drums/Surface No Exemptions
None
Not Applicable

WHMIS CLASSIFICATION: B3, D2B

***** EXPORT HAZ MAT DESCRIPTON *****
UN1993, FLAMMABLE LIQUIDS N.O.S., (Naphtha Solvent), 3, PGIII
SECTION XV: REGULATORY INFORMATION

All components appear on Canadian DSL and US TSCA lists.

CERCLA RQ 40 CFR 302.4: None
SARA 302 Components 40 CFR Appendix A:

NONE

Section 311/312 Hazard Class 40 CFR 370.2

Immediate (X) Delayed ( )
Fire (X)

Reactive ( )

Sara 313 Components 40 CFR 372.65

Section 313 Component(s)
Zinc Compounds

CAS Number
7440-66-6

Sudden Release of Pressure ( )

Max. %
20-30

International Regulations
Inventory Status
ACOIN (AUSTRALIA) The intentional ingredients of this product are listed.
DSL (CANADA) The intentional ingredients of this product are listed.
EINECS (EUROPE) The intentional ingredients of this product are listed.
ENCS (JAPAN) The intentional ingredients of this product are listed.
State and Local Regulations
California Proposition 65:

NONE

New Jersey RTK Label Information:

Stoddard Solvent

8052-41-3

Pennsylvania RTK Label Information:

Stoddard Solvent

8052-41-3

SECTION XVI: OTHER INFORMATION

The information accumulated herein is believed to be accurate but is not warranted to be whether originating with
the company or not. Recipients are advised to confirm in advance of need that the information is current, applicable,
and suitable to their circumstances.

Tectyl 502C Class I [3114]

5/23/12

Page 4 of 4