Scribd Logo
Upload

Welcome to Scribd!

  • 163 views

    122E

    Uploaded by

    Ahmed Ali Mahmoud
    The Type 122E is an explosion proof I/P converter designed to integrate with pneumatic valve positioners. It converts a 4-20mA electrical signal to a proportional 3-15 psig pneumatic output to control actuator pressure and valve position. It uses proven moving coil and nozzle technology with integrated flow regulation. It is compact and rugged for industrial applications like pulp/paper and chemical plants. It has IP66 weatherproofing and ATEX certification for hazardous areas.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    122E

    Uploaded by

    Ahmed Ali Mahmoud
    163 views4 pages
    The Type 122E is an explosion proof I/P converter designed to integrate with pneumatic valve positioners. It converts a 4-20mA electrical signal to a proportional 3-15 psig pneumatic output to control actuator pressure and valve position. It uses proven moving coil and nozzle technology with integrated flow regulation. It is compact and rugged for industrial applications like pulp/paper and chemical plants. It has IP66 weatherproofing and ATEX certification for hazardous areas.

    Original Description:

    manual

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The Type 122E is an explosion proof I/P converter designed to integrate with pneumatic valve positioners. It converts a 4-20mA electrical signal to a proportional 3-15 psig pneumatic output to control actuator pressure and valve position. It uses proven moving coil and nozzle technology with integrated flow regulation. It is compact and rugged for industrial applications like pulp/paper and chemical plants. It has IP66 weatherproofing and ATEX certification for hazardous areas.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    163 views4 pages

    122E

    Uploaded by

    Ahmed Ali Mahmoud
    The Type 122E is an explosion proof I/P converter designed to integrate with pneumatic valve positioners. It converts a 4-20mA electrical signal to a proportional 3-15 psig pneumatic output to control actuator pressure and valve position. It uses proven moving coil and nozzle technology with integrated flow regulation. It is compact and rugged for industrial applications like pulp/paper and chemical plants. It has IP66 weatherproofing and ATEX certification for hazardous areas.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 4

    TYPE 122E

    Explosion Proof I/P

    The Type 122E Explosion Proof I/P converter


    designed for positioner integration, which can
    typically convert a pneumatic positioner to
    operate as an electro-pneumatic positioner
    using proven moving coil and flapper/nozzle
    technology, with a built in flow regulator to
    minimize supply pressure effects.
    Low Cost OEM I/P
    Valve Positioner Pilot
    Compact and Rugged
    Specific Application Customising
    Wide Supply Range Available
    ATEX Certified
    IP66

    TYPICAL APPLICATIONS

    Functional Symbol

    Industry:

    Any industry requiring higher


    flows or pressures, i.e Pulp and
    Paper,
    Water
    treatment,
    Chemical and Power Plant

    4-20mA Signal
    Process
    valve

    I/P
    Air supply
    Positioner

    Solution:

    Accurate control of the position of


    motion control valves via an actuator
    with accurate positioner control

    Type 122E

    Watson Smith Instrumentation

    Technical Data
    Pneumatic
    Output Pressure

    3-15psig;

    Air Supply

    Oil free, dry air, filtered to <5 microns;


    20-150 psig (1.4 10bar)

    Air Consumption

    <1.5 nl/min typical

    Response Time
    Linearity
    Hysteresis

    </=650msecs from 10 to 90% or


    </=350ms from 90 to 10% of output pressure into a 5cc load)
    +/-0.5% of span
    +/-0.3% of span

    Temperature Effect

    Typically less than 0.2% span/deg C between -40C to +85C

    Supply Sensitivity

    Less than+/- 0.15% of span for supply pressure change

    Connections

    Customised to suit customers requirements

    Electrical
    Electrical Signal

    4-20mA (two wire);

    Loop Resistance

    <250 Ohm

    Failure Mode

    Signal falls to below 1.7psig (0.12 bar) in <2sec, when input signal fails

    Insulation Resistance

    >100M Ohm at 850Vdc, electrical terminals to case

    Connections

    Clamping screw connector terminals.

    -ve control signal connection

    +ve control signal

    connection

    Physical
    Operating Temperature

    -40C to +85C

    Weatherproofing

    IP66

    Vibration

    Output pressure changes less than 2% for 2g sine 20-100Hz,

    Electromagnetic
    Compatibility

    Compliant with EC requirements


    EN 50081-1:1994 (Emissions) and EN50082 2:1995 (Immunity)

    Material of Construction

    Aluminium housing with nitrile diaphragms, customer specific enclosures available

    Mounting Position

    Any orientation (re-calibration may be required)

    Type 122E

    Watson Smith Instrumentation

    MOUNTING POSITION

    PNEUMATIC INSTALLATION

    INTRINISICALLY SAFE SYSTEM INSTALLATION

    Dwg No. 96-133E

    HAZARDOUS AREA CERTIFICATION


    The Type 122E is supplied certified for use in Explosion Proof, Intrinsically Safe and Type nL applications, to ATEX requirements.

    Norgren Ltd.,
    Cross Chancellor Street,
    Leeds, LS6 2RT. England.
    Telephone: +44 (0) 113 245 7587
    Fax: +44 (0) 113 246 5735
    Email: [email protected]

    ds122E_c_04/07
    Controlled Doc. No. 2007-036a

    All instruments are tested on the Watson Smith Automatic Testing System and an individual test certificate is provided
    at no extra charge. Each unit is tested for linearity, hysteresis, total error, air consumption, response time and supply
    sensitivity.
    Our policy is one of continuous research and development. We therefore reserve the right to amend without
    notice the specifications given in this document. Customers are responsible for ensuring that the product is
    used only for the purpose for which it is intended. In case of doubt Norgren will be pleased to advise.

    Type 122E

    Watson Smith Instrumentation

    Thank you for reading this data sheet.


    For pricing or for further information, please contact us at our UK Office, using the details
    below.

    UK Office
    Keison Products,
    P.O. Box 2124, Chelmsford, Essex, CM1 3UP, England.
    Tel: +44 (0)1245 600560
    Fax: +44 (0)1245 808399
    Email: [email protected]
    Please note - Product designs and specifications are subject to change without notice. The user is responsible for determining the
    suitability of this product.

    You might also like