LG 55LW9500 Ch. LB12D

Internal Use Only
North/Latin America
Europe/Africa
Asia/Oceania
http://aic.lgservice.com
http://eic.lgservice.com
http://biz.lgservice.com
LED LCD TV
SERVICE MANUAL
CHASSIS : LB12D
MODEL : 55LW9500
55LW9500-TA
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
P/NO : MFL67007005 (1104-REV00)
Printed in Korea
CONTENTS
CONTENTS .............................................................................................. 2
PRODUCT SAFETY ................................................................................. 3
SPECIFICATION ....................................................................................... 4
ADJUSTMENT INSTRUCTION ................................................................ 8
EXPLODED VIEW .................................................................................. 16
SCHEMATIC CIRCUIT DIAGRAM ..............................................................
Copyright 2011 LG Electronics. Inc. All rights reserved.

Only for training and service purposes
-2-
LGE Internal Use Only
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by
in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during the

servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1 W), keep the resistor 10 mm away from PCB.
Do not use a line Isolation Transformer during this check.

Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
0.5 mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit

Keep wires away from high voltage or high temperature parts.
AC Volt-meter
Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1 M and 5.2 M.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

-3-
To Instruments
exposed
METALLIC PARTS
0.15 uF
Good Earth Ground

such as WATER PIPE,
CONDUIT etc.
1.5 Kohm/10W
When 25A is impressed between Earth and 2nd Ground

for 1 second, Resistance must be less than 0.1
*Base on Adjustment standard
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
3. Test method
This specification is applied to the LCD TV used LB12D

chassis.
1) Performance: LGE TV test method followed

2) Demanded other specification
- Safety : CE, IEC specification
- EMC : CE, IEC
2. Requirement for Test

Each part is tested as below without special appointment.
1) Temperature: 25 C 5 C(77 F 9 F), CST: 40 C 5 C
2) Relative Humidity : 65 % 10 %
3) Power Voltage
: Standard input voltage (AC 100-240 V~, 50/60 Hz)
* Standard Voltage of each products is marked by models.
4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM.
5) The receiver must be operated for about 5 minutes prior to
the adjustment.
4. Model General Specification

No.
1.
Item
Market
Specification
Remarks
ASIA, Oceania, Africa,
DTV & Analog
Middle East(PAL/DVB Market)
* DTV Region : Australia/New Zealand(AU), Singapore(SG), Indonesia(ID),
1) PAL-B/G
* Australia/India : only PAL
Malaysia(MY), Vietnam(VN), South Africa(ZA), Iran(IR)

2.
Broadcasting system
2) PAL-D/K
3) PAL-I/I
3) SECAM-DK, BG, I
4) DVB-T
3.
Receiving system
Analog : Upper Heterodyne
Digital : COFDM, QAM
- Guard Interval(Bitrate_Mbit/s)
DVB-T
1/4, 1/8, 1/16, 1/32
- Modulation : Code Rate

QPSK
: 1/2, 2/3, 3/4, 5/6, 7/8
16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8

64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
4.
Video Input RCA (2EA)
PAL, SECAM, NTSC
5.
Head phone out
Antena, AV1, AV3, Component1,
4 System : PAL, SECAM, NTSC, PAL60

Rear 1EA, AV gender jack 1EA
Component2, RGB, HDMI1, HDMI2,

HDMI3, HDMI4, USB1, USB2
6.
Component Input (2EA)
Y/Cb/Cr, Y/Pb/Pr
7.
RGB Input (1EA)
RGB-PC
Rear 1EA, Gender 1EA

Analog(D-SUB 15PIN)
8.
HDMI Input (4EA)
HDMI1-ARC
PC(HDMI version 1.3) Support HDCP
HDMI2
HDMI3
HDMI4
9.
Audio Input (5EA)
RGB/DVI Audio
L/R Input
Component1,2
AV1,2
10.
SDPIF out (1EA)
SPDIF out
11.
USB (2EA)
EMF, DivX HD, For SVC(download)

JPEG, MP3, DivX HD Plus
-4-
5. Component Video Input (Y, CB/PB, CR/PR)

No.
1.
Specification
Resolution
720x480
H-freq(kHz)
Remark
V-freq(Hz)
15.73
60.00
SDTV,DVD 480i
2.
720x480
15.63
59.94
SDTV,DVD 480i
3.
720x480
31.47
59.94
480p
4.
720x480
31.50
60.00
480p
5.
720x576
15.625
50.00
SDTV,DVD 625 Line
6.
720x576
31.25
50.00
HDTV 576p
7.
1280x720
45.00
50.00
HDTV 720p
8.
1280x720
44.96
59.94
HDTV 720p
9.
1280x720
45.00
60.00
HDTV 720p
10.
1920x1080
31.25
50.00
HDTV 1080i
11.
1920x1080
33.75
60.00
HDTV 1080i
12.
1920x1080
33.72
59.94
HDTV 1080i
13.
1920x1080
56.250
50
HDTV 1080p
14.
1920x1080
67.5
60
HDTV 1080p
6. RGB (PC)
No.
Specification
Resolution
H-freq(kHz)
V-freq(Hz)
Pixel Clock(MHz)
Proposed
Remarks
Input 848*480 60 Hz, 852*480 60 Hz
1.
720*400
31.468
70.08
28.321
2.
640*480
31.469
59.94
25.17
VESA
For only DOS mode
3.
800*600
37.879
60.31
40.00
VESA
4.
1024*768
48.363
60.00
65.00
VESA(XGA)
5.
1360*768
47.72
59.8
84.75
WXGA
6.
1920*1080
66.587
59.93
138.625
WUXGA
-> 640*480 60 Hz Display
FHD model
7. HDMI Input
(1) DTV Mode
No.
Resolution
H-freq(kHz)
V-freq.(Hz)
59.94 /60
Pixel clock(MHz)
1.
720*480
31.469 /31.5
2.
720*576
31.25
50
54
SDTV 576P
3.
1280*720
37.500
50
74.25
HDTV 720P
4.
1280*720
44.96 /45
59.94 /60
74.17/74.25
HDTV 720P
5.
1920*1080
33.72 /33.75
59.94 /60
74.17/74.25
HDTV 1080I
6.
1920*1080
28.125
50.00
74.25
HDTV 1080I
7.
1920*1080
26.97 /27
23.97 /24
74.17/74.25
HDTV 1080P
8.
1920*1080
33.716 /33.75
29.976 /30.00
74.25
HDTV 1080P
9.
1920*1080
56.250
50
148.5
HDTV 1080P
10.
1920*1080
67.43 /67.5
59.94 /60
148.35/148.50
HDTV 1080P

27.00/27.03
Proposed
-5-
Remark
SDTV 480P
(2) PC Mode
No.
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
Proposed
Remark
1.
720*400
31.468
70.08
28.321
2.
640*480
31.469
59.94
25.17
VESA
HDCP
3.
800*600
37.879
60.31
40.00
VESA
HDCP
4.
1024*768
48.363
60.00
65.00
VESA(XGA)
HDCP
5.
1360*768
47.72
59.8
84.75
WXGA
HDCP
6.
1920*1080
67.5
60.00
138.625
WUXGA
HDCP/FHD model
HDCP
9. 3D Mode - HDMI & USB

(1) HDMI Input (V1.4a)
No.
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
Proposed
3D input proposed mode
1920*1080
53.95 / 54
23.98 / 24
148.35/148.5
HDTV 1080P
Frame packing
1280*720
89.9 / 90
59.94/60
148.35/148.5
HDTV 720P
Frame packing
1280*720
75
50
148.5
HDTV 720P
Frame packing
1920*1080
67.5
60
148.5
HDTV 1080P
Side by Side(half), Top and bottom
1920*1080
56.3
50
148.5
HDTV 1080P
Side by Side(half), Top and bottom
1280*720
45
60
74.25
HDTV 720P
Side by Side(half), Top and Bottom
1280*720
37.5
50
74.25
HDTV 720P
1920*1080
33.7
60
74.25
HDTV 1080i
1920*1080
28.1
50
74.25
HDTV 1080i
10
1920*1080
27
24
74.25
HDTV 1080P
11
1920*1080
33.7
30
89.1
HDTV 1080P
(2) HDMI Input(1.3)

No
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
Proposed
1280*720
45.00
60.00
74.25
HDTV 720P
Side by Side, Top & Bottom
1280*720
37.500
50
74.25
HDTV 720P
1920*1080
33.75
60.00
74.25
HDTV 1080I
1920*1080
28.125
50.00
74.25
HDTV 1080I
1920*1080
27.00
24.00
74.25
HDTV 1080P
Side by Side, Top & Bottom, Checkerboard
1920*1080
33.75
30.00
74.25
HDTV 1080P
1920*1080
67.50
60.00
148.5
HDTV 1080P
1920*1080
56.250
50
148.5
HDTV 1080P
Single Frame Sequential


-6-
(3) RF 3D Input(DTV)
No.
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
Proposed
1280*720
37.500
50
74.25
HDTV 720P
1920*1080
28.125
50
74.25
HDTV 1080I
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
Proposed
67.5
60
148.5
HDTV 1080P
(4) RGB-PC Input

No.
1
Resolution
1920*1080
(5) DLNA
No.
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
Proposed
1920*1080
33.75
30
74.25
HDTV 1080P
Side by Side, Top & Bottom,

Checkerboard
(6) USB Input

No.
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
1920*1080
33.75
30.000
74.25
Side by Side
Proposed
HDTV 1080P
Top & Bottom

Checkerboard
(7) DVR
No.
1
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
ALL
Side by Side
Proposed
Top & Bottom
(8) 3D Input mode

No.
Side by Side
Top & Bottom
Checkerboard
Frame Packing
2D to 3D
1
L

-7-
2D to 3D
ADJUSTMENT INSTRUCTION
1. Application Range
(3) Adjustment
1) Adjustment method
- Using RS-232, adjust items in the other shown in
3.1.(3).3)
This specification sheet is applied to all of the LED LCD TV

with LB12D chassis.
2) Adj. protocol
2. Designation
Protocol
1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
2) Adjustment must be done in the correct order.
3) The adjustment must be performed in the circumstance of
25 C 5 C of temperature and 65 % 10 % of relative
humidity if there is no specific designation.
4) The input voltage of the receiver must keep AC 100-240
V~, 50/60 Hz.
5) The receiver must be operated for about 5 minutes prior to
the adjustment when module is in the circumstance of over
15.
Command
aa 00 00
a 00 OK00x
Source change
xb 00 40
b 00 OK40x (Adjust 480i, 1080p Comp1 )
xb 00 60
b 00 OK60x (Adjust 1920*1080 RGB)
Begin adj.
ad 00 10
Return adj. result
OKx (Case of Success)

NGx (Case of Fail)
Read adj. data
Confirm adj.
(main)
(main)
ad 00 20
000000000000000000000000007c007b006dx
(sub)
(Sub)
ad 00 21
000000070000000000000000007c00830077x
ad 00 99
NG 03 00x (Fail)
In case of keeping module is in the circumstance of 0 C, it

should be placed in the circumstance of above 15 C for 2
hours.
NG 03 01x (Fail)
NG 03 02x (Fail)
OK 03 03x (Success)
End adj.
In case of keeping module is in the circumstance of below 20 C, it should be placed in the circumstance of above 15
C for 3 hours.
aa 00 90
a 00 OK90x
Ref.) ADC Adj. RS232C Protocol_Ver1.0

3) Adj. order
- aa 00 00 [Enter ADC adj. mode]
- xb 00 04 [Change input source to Component1 (480i&
1080p)]
- ad 00 10 [Adjust 480i&1080p Comp1]
- xb 00 06 [Change input source to RGB(1024*768)]
- ad 00 10 [Adjust 1920*1080 RGB]
- ad 00 90 End adj.
[Caution]
When still image is displayed for a period of 20 minutes or
longer (especially where W/B scale is strong. Digital pattern
13ch and/or Cross hatch pattern 09ch), there can some
afterimage in the black level area.
3. Automatic Adjustment
3.1. ADC Adjustment
Set ACK
Enter adj. mode
3.2. MAC Address
(1) Overview
ADC adjustment is needed to find the optimum black level
and gain in Analog-to-Digital device and to compensate
RGB deviation.
(1) Equipment & Condition

- Play file: Serial.exe
- MAC Address edit
- Input Start / End MAC address

1) Jig (RS-232C protocol)
2) MSPG-925 Series Pattern Generator(MSPG-925FA,
pattern - 65)
- Resolution : 480i Comp1
1080P Comp1
1920*1080 RGB
- Pattern : Horizontal 100% Color Bar Pattern
- Pattern level : 0.70.1 Vp-p
- Image
(2) Download method

1) Communication Prot connection
PCBA
PC(RS-232C)
RS-232C Po rt
Connect: PCBA Jig-> RS-232C Port== PC-> RS-232C Port

-8-
3.4. LAN PORT INSPECTION(PING TEST)
2) MAC Address Download, Whidevine Download

- Com 1,2,3,4 and 115200(Baud rate)
Connect SET -> LAN port == PC -> LAN Port
SET
PC
(1) Equipment setting

1) Play the LAN Port Test PROGRAM.
2) Input IP set up for an inspection to Test Program.
*IP Number : 12.12.2.2
(2) LAN PORT inspection (PING TEST)
1) Play the LAN Port Test Program.
2) Connect each other LAN Port Jack.
3) Play Test (F9) button and confirm OK Message.
4) Remove LAN CABLE
3.3. LAN
A Each other connection to LAN Port of IP Hub and Jig
(2) LAN inspection solution

A LAN Port connection with PCB
A Network setting at MENU Mode of TV
A Setting automatic IP
A Setting state confirmation
-> If automatic setting is finished, you confirm IP and
MAC Address.
3.5. Model name & Serial number Download

(1) Model name & Serial number D/L
A Press Power on key of service remote control.
(Baud rate : 115200 bps)
A Connect RS232 Signal Cable to RS-232 Jack.
A Write Serial number by use RS-232.
A Must check the serial number at Instart menu.
(2) Method & notice
A. Serial number D/L is using of scan equipment.
B. Setting of scan equipment operated by Manufacturing
Technology Group.
C.Serial number D/L must be conformed when it is
produced in production line, because serial number D/L
is mandatory by D-book 4.0
(3) WIDEVINE key Inspection

- Confirm key input data at the IN START MENU Mode.

-9-
* Manual Download (Model Name and Serial Number)

If the TV set is downloaded by OTA or service man, sometimes
model name or serial number is initialized.(Not always)
It is impossible to download by bar code scan, so It need
Manual download.
a. Press the instart key of ADJ remote control.
b. Go to the menu 6.Model Number D/L like below photo.
c. Input the Factory model name(ex 42LD450-TA) or Serial
number like photo.
4. Manual Adjustment
4.1. ADC Adjustment
4.1.1. Overview
ADC adjustment is needed to find the optimum black level and
gain in Analog-to-Digital device and to compensate RGB
deviation.
4.1.2. Equipment & Condition

(1) Adjust Remote control
(2) 801GF(802B, 802F, 802R) or MSPG925FA Pattern Generator
- Resolution :
480i,720*480(MSPG-925FA -> Model: 209, Pattern: 65) 480i
1080p, 1920*1080(MSPG-925FA -> Model: 225, Pattern:
65) - 1080p
- Pattern : Horizontal 100 % Color Bar Pattern
- Pattern level: 0.7 0.1 Vp-p
- Image
d. Check the model name Instart menu -> Factory name

displayed (ex 42LE7500-TA)
e. Check the Diagnostics(DTV country only) -> Buyer model
displayed (ex 42LE7500-TA)
3.6. WIFI MAC ADDRESS CHECK

a. Using RS232
Transmission
H-freq(kHz)
V-freq.(Hz)
[A][I][][Set ID][][20][Cr]
[O][K][X] or [NG]
(3) Must use standard cable
b. Check the menu on in-start
4.1.3. Adjust method

(1) ADC 480i, 1080p Comp1
1) Check connected condition of Component 1 cable to the
equipment.
2) Give a 480i, 1080p Mode, Horizontal 100% Color Bar
Pattern to Component 1.
(MSPG-925FA -> Model: 209, Pattern: 65) - 480i
(MSPG-925FA -> Model: 225, Pattern: 65) - 1080p
3) Change input mode as Component1 and picture mode
as Standard
4) Press the In-start Key on the ADJ remote control after at
least 1 min of signal reception. Then, select 7. External
ADC -> 1. COMP 1080p on the menu. Press enter key.
The adjustment will start automatically.
5) If ADC calibration is successful, ADC RGB Success is
displayed. If ADC calibration is failure, ADC RGB Fail
is displayed.
6) If ADC calibration is failure, after recheck ADC pattern or
condition retry calibration. Error message refer to 5).
(2) ADC 1920*1080 RGB
1) Check connected condition of Component & RGB cable
to the equipment
2) Give a 1920*1080 Mode, 100 % Horizontal Color Bar
Pattern to RGB port.
(MSPG-925 Series -> model: 225 , pattern: 65 )
3) Change input mode as RGB and picture mode as Standard.
4) Press the In-start key on the ADJ remote control after at
least 1 min of signal reception. Then, select 7. External
ADC -> 1. COMP 1080p on the menu. Press enter key.
The adjustment will start automatically.
5) If ADC calibration is successful, ADC RGB Success is
displayed. If ADC calibration is failure, ADC RGB Fail
is displayed.
6) If ADC calibration is failure, after recheck ADC pattern or
condition retry calibration. Error message refer to 5).
- 10 -
4.2. EDID(The Extended Display Identification

Data)/DDC(Display Data Channel) download
* Physical Add & Checksum(HDMI1/2/3/4)

INPURT
(1) Overview
It is a VESA regulation. A PC or a MNT will display an
optimal resolution through information sharing without any
necessity of user input. It is a realization of Plug and Play.
(2) Equipment
- Adjust remote control
- Since embedded EDID data is used, EDID download JIG,
HDMI cable and D-sub cable are not need.
For HDMI EDID
D-sub to D-sub
DVI-D to HDMI or HDMI to HDMI
FFh(Checksum)
10
00
CB
HDMI 2
20
00
BB
HDMI 3
30
00
AB
HDMI 4
40
00
9B
4.3. White Balance Adjustment

4.3.1 Overview
(1) W/B adj. Objective & How-it-works
(2) Objective: To reduce each Panels W/B deviation
(3) How-it-works : When R/G/B gain in the OSD is at 192, it
means the panel is at its Full Dynamic Range. In order to
prevent saturation of Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is lowered to find
the desired value.
(4) Adjustment condition : normal temperature
1) Surrounding Temperature : 25 C 5 C
2) Warm-up time: About 5 Min
3) Surrounding Humidity : 20 % ~ 80 %
(3)Download method
1) Press Adjust key on the Adjustment remote control then
select 10.EDID D/L, By pressing Enter key, enter EDID
D/L menu.
2) Select [Start] button by pressing Enter key, HDMI1/
HDMI2/ HDMI3/ HDMI4/ RGB are Writing and display
OK or NG
For Analog EDID
9Eh/9Fh(Physical Add)
HDMI 1
4.3.2 Equipment
1) Color Analyzer: CA-210 (LED Module : CH 14)
2) Adjustment Computer(During auto adj., RS-232C protocol is
needed)
3) Adjust Remote control
4) Video Signal Generator MSPG-925F 720p/216-Gray
(Model: 217, Pattern: 78)
-> Only when internal pattern is not available
A Color Analyzer Matrix should be calibrated using CS-1000
(4) EDID DATA

A RGB
0
00
FF
FF
FF
FF
FF
FF
00
1E
6D
01
00
01
01
01
01
10
01
15
01
03
68
10
09
78
0A
EE
91
A3
54
4C
99
26
20
0F
50
54
A1
08
00
71
40
81
C0
81
00
81
80
95
00
30
90
40
A9
C0
40
45
00
A0
5A
50
40
70
36
00
60
3E
1E
53
10
70
00
4C
47
20
B3
00
02
3A
80
00
00
00
1E
66
A0
5A
00
00
00
00
0A
20
20
20
54
56
0A
20
20
18
71
38
21
50
B0
1E
00
00
20
20
20
20
20
2D
40
58
51
00
1B
30
00
FD
00
3A
00
00
00
FC
20
20
20
00
98
4.3.3. Equipment connection MAP

Co lo r Analyzer
2C
HDMI(FHD 3D, HDMI 1.4a, 3D)
RS -232C
Probe
Co m p ut er
RS -232C
RS -232C
Pat t ern Generat o r

Signal Source
* If TV internal pattern is used, not needed
4.3.4. Adj. Command (Protocol)
00
FF
FF
FF
FF
FF
FF
00
1E
6D
01
00
01
01
01
01
10
01
14
01
03
80
10
09
78
0A
EE
91
A3
54
4C
99
26
20
0F
50
54
A1
08
00
71
4F
81
01
01
01
01
01
01
01
30
01
01
01
01
01
01
02
3A
80
18
71
38
2D
40
58
2C
40
45
00
A0
5A
00
00
00
1E
01
1D
00
72
51
D0
1E
20
50
6E
28
55
00
A0
5A
00
00
00
1E
00
00
00
FD
00
3A
60
3E
1E
53
10
00
0A
20
20
20
20
20
20
00
00
00
FC
70
00
4C
47
20
54
56
0A
20
20
20
20
20
20
20
01
D7
80
02
03
37
F1
4E
10
1F
84
13
05
14
03
02
12
20
21
90
22
15
01
26
15
07
50
09
57
07
78
03
0C
00
XX
XX
A0
B8
2D
20
C0
0E
01
40
0A
3C
08
10
18
10
98
10
58
B0
10
38
10
E3
05
03
01
01
1D
80
18
71
1C
16
20
58
C0
2C
25
00
A0
5A
00
00
00
9E
01
1D
00
80
51
D0
1A
D0
20
6E
88
55
00
A0
5A
00
00
00
1A
02
3A
80
18
71
E0
38
2D
40
58
2C
45
00
A0
5A
00
00
00
1E
00
00
00
F0
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
XX

<Command Format>
LEN
CMD
VAL
CS
- LEN: Number of Data Byte to be sent

- CMD: Command
- VAL: FOS Data value
- CS: Checksum of sent data
- A: Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]
- 11 -
(2) Manual adj. method

1) Set TV in Adj. mode using POWER ON.
2) Zero Calibrate the probe of Color Analyzer, then place it
on the center of LCD module within 10 cm of the surface.
3) Press ADJ key -> EZ adjust using adj. R/C -> 7. WhiteBalance then press the cursor to the right (KEY G).
(When KEY(G) is pressed 216 Gray internal pattern will
be displayed)
4) One of R Gain / G Gain / B Gain should be fixed at 192,
and the rest will be lowered to meet the desired value.
5) Adj. is performed in COOL, MEDIUM, WARM 3 modes
of color temperature.
RS-232C Command used during auto-adjustment.
RS-232C COMMAND
Explanation
[CMD
ID
DATA]
wb
00
00
wb
00
10
Gain adj.(internal white pattern)
wb
00
1f
Gain adj. completed
wb
00
20
Offset adj.(internal white pattern)
wb
00
2f
Offset adj. completed
wb
00
ff
End White Balance adj.(Internal pattern disappears)
Begin White Balance adj.
Ex) wb 00 00 -> Begin white balance auto-adj.

wb 00 10 -> Gain adj.
ja 00 ff -> Adj. data
jb 00 c0
...
...
wb 00 1f -> Gain adj. completed
*(wb 00 20(Start), wb 00 2f(end)) -> Off-set adj.
wb 00 ff -> End white balance auto-adj.
A
Adj. Map
ITEM
Cool
Command
Data Range(Hex.)
Cmd 1
Cmd 2
Min
Max
R-Gain
00
C0
G-Gain
00
C0
B-Gain
00
C0
R-Gain
00
C0
G-Gain
00
C0
B-Gain
00
C0
Default
(Decimal)
R-Cut
G-Cut
B-Cut
Medium
A
A
G-Cut
B-Cut
Adj. condition and cautionary items

1) Lighting condition in surrounding area
Surrounding lighting should be lower 10 lux. Try to
isolate adj. area into dark surrounding.
2) Probe location
: Color Analyzer (CA-210) probe should be within 10
cm and perpendicular of the module surface (80 ~
100)
3) Aging time
- After Aging Start, Keep the Power ON status during
5 Minutes.
- In case of LCD, Back-light on should be checked
using no signal or Full-white pattern.
Luminance : 204 Gray

Standard color coordinate and temperature using CS-1000
(over 26 inch)
Mode
R-Gain
00
C0
G-Gain
00
C0
B-Gain
00
C0
Color Coordination
x
Temp
UV
COOL
0.269
0.273
13000 K
0.0000
R-Cut
MEDIUM
0.285
0.293
9300 K
0.0000
G-Cut
WARM
0.313
0.329
6500 K
0.0000
4.3.5. Adj. method
(1) Auto adj. method

1) Set TV in adj. mode using POWER ON key.
2) Zero calibrate probe then place it on the center of the
Display.
3) Connect Cable (RS-232C)
4) Select mode in adj. Program and begin adjustment.
5) When adj. is complete (OK Sign), check adj. status pre
mode. (Warm, Medium, Cool)
6) Remove probe and RS-232C cable to complete adj.
A
If internal pattern is not available, use RF input. In EZ

Adj. menu 7.White Balance, you can select one of 2
Test-pattern: ON, OFF. Default is inner(ON). By selecting
OFF, you can adjust using RF signal in 216 Gray pattern.
4.3.6. Reference (White Balance Adj. coordinate and

color temperature)
R-Cut
Warm
Standard color coordinate and temperature using CA-210

(CH 9)
Mode
Color Coordination
x
Temp
UV
COOL
0.269 0.002
0.273 0.002 13000 K
0.0000
MEDIUM
0.285 0.002
0.293 0.002
9300 K
0.0000
WARM
0.313 0.002
0.329 0.002
6500 K
0.0000
W/B Adj. must begin as start command wb 00 00 , and

finish as end command wb 00 ff, and Adj. offset if need.

- 12 -
4.5. EYE-Q function check
4.3.7. ALELF & EDGE LED White banlance table

- ALELF&EDGE LED module change color coordinate
because of aging time.
- Apply under the color coordinate table, for compensated
aging time.
- ALEF - LGD Only
Aging Time
GP3
(Min.)
Cool
Medium
Step 1) Turn on TV.

Step 2) Press EYE key of Adjustment remote control.
Step 3) Cover the Eye Q II sensor on the front of the using
your hand and wait for 6 seconds.
Step 4) Confirm that R/G/B value is lower than 10 of the Raw
Data (Sensor data, Back light). If after 6 seconds,
R/G/B value is not lower than 10, replace Eye Q II
sensor.
Step 5) Remove your hand from the Eye Q II sensor and wait
for 6 seconds.
Step 6) Confirm that ok pop up. If change is not seen,
replace Eye Q II sensor.
Warm
269
273
285
293
313
329
0-2
282
294
298
314
322
343
3-5
281
292
297
312
321
341
6-9
280
291
296
311
320
340
10-19
279
289
295
309
319
338
20-35
277
284
293
304
317
333
36-49
274
279
290
299
314
328
50-79
271
277
287
297
311
326
80-149
270
274
286
294
310
323
Over 150
269
273
285
293
309
322
4.6. Local Dimming Function Check

Step 1) Turn on TV.
Step 2) At the Local Dimming mode, module Edge Backlight
moving right to left Back light of IOP module moving.
Step 3) Confirm the Local Dimming mode.
Step 4) Press exit key.
4.4. Wireless function check

Step 1) Connect set and Dongle of Wireless to Cable of HDMI
& TTA 20Pin.
Step 2) At OSD of SET, check the message like Fig 3.
Step 3) Detach Cable of Wireless Dongle.
Local Dimming Demo (Edge LED Model)
Connect
Fig.1
Local Dimming Demo (IOP & ALEF Model)
Fig.2
4.7. Magic Motion Remote control test

- Equipment : RF Remote control for test, IR-KEY-Code
Remote control for test
- You must confirm the battery power of RF-Remote control
before test(recommend that change the battery per every lot)
- Sequence (test)
1) if you select the start(Mute) key on the controller, you
can pairing with the TV SET.
2) You can check the cursor on the TV Screen, when select
the OK key on the controller.
3) You must remove the pairing with the TV Set by select
OK Key + Mute key on the controller for 5 seconds.
Fig.3 Connect the Dongle

- 13 -
4.8. 3D function test
4.9. Option selection per country
(Pattern Generator MSHG-600, MSPG-6100[Support HDMI1.4])

* HDMI mode NO. 872 , pattern No.83
(1) Overview
- Option selection is only done for models in NON-AU/-ID/SG/-MY/-VN/-IL/-ZA/-IR
- Applied model: LB12C/D/E Chassis applied Asia/MEA
model
1) Please input 3D test pattern like below (HDMI mode No.

872 , pattern No.83)
(2) Method
1) Press ADJ key on the Adjustment remote control, then
select Country Group Menu
2) Depending on destination, select Country Group Code
12 or Country Group A-ASIA.
3) Press ADJ key on the Adjustment remote control, then
select Area Option.
4) Depending on Area code number, select Default Lang.,
Wi-Fi Frequency, Lang Gr., Teletext Lang Gr., I II Save,
HDEV, MONO, Location.
2) When 3D OSD appear automatically , then select OK
button.
4.10. Tool Option selection

- Method : Press Adj. key on the Adj. Remote Control, then
select Tool option.
Module
Tool 1
Tool 2
Tool 3
Tool 4
Tool 5
Tool 6
Remark
LGD
33035
4811
3327
17593
47701
727
STD B/L: 60
4.11. Ship-out mode check(In-stop)

After final inspection, press IN-STOP key of the Adjustment
remote control and check that the unit goes to Stand-by
mode.
4.12. GND and Internal Pressure check

3) Dont wear a 3D Glasses, Check the picture like below .
4.8.1. IR emitter inspection.

1) Start 3D pattern inspection.
2) If IR emitter signal is correctly received to IR receiver, the
lamp of IR tester turn on
(2) Checkpoint
TEST voltage
- GND: 1.5 KV / min at 100 mA
- SIGNAL: 3 KV / min at 100 mA
TEST time: 1 second
TEST POINT
- GND TEST = POWER CORD GND & SIGNAL CABLE
METAL GND
- Internal Pressure TEST = POWER CORD GND & LIVE
& NEUTRAL
LEAKAGE CURRENT: At 0.5 mArms
<IR Emitter inspection>
<IR Tester Lamp turned off(NG)>
(1) Method
1) GND & Internal Pressure auto-check preparation
- Check that Power Cord is fully inserted to the SET.
(If loose, re-insert)
2) Perform GND & Internal Pressure auto-check
- Unit fully inserted Power cord, Antenna cable and A/V
arrive to the auto-check process.
- Connect D-terminal to AV JACK TESTER
- Auto CONTROLLER(GWS103-4) ON
- Perform GND TEST
- If NG, Buzzer will sound to inform the operator.
- If OK, changeover to I/P check automatically.
(Remove CORD, A/V form AV JACK BOX)
- Perform I/P test
- If NG, Buzzer will sound to inform the operator.
- If OK, Good lamp will lit up and the stopper will allow
the pallet to move on to next process.
<IR Tester Lamp turned on(OK)>

- 14 -
5. Audio
No.
Item
Min.
Typ.
Max.
Unit
1.
Audio practical max
9.0
10.0
12.0
8.5
8.9
9.8
Vrms
10.0
15.0
Output, L/R
(Distortion=10 %
EQ Off
AVL Off
Clear Voice Off
max Output)
2.
Speaker (8
Impedance)
EQ On
AVL On
Clear Voice On
Measurement condition:
1. RF input: Mono, 1 KHz sine wave signal, 100 % Modulation
2. CVBS, Component: 1 KHz sine wave signal 0.5 Vrms
3. RGB PC: 1 KHz sine wave signal 0.7 Vrms
6. USB S/W download(Service only)

1) Put the USB Stick to the USB socket.
2) Automatically detecting update file in USB Stick.
- If your downloaded program version in USB Stick is Low,
it didnt work. But your downloaded version is High, USB
data is automatically detecting.
3) Show the message Copying files from memory.
4) Updating is starting.
5) Updating Completed, The TV will restart automatically.

6) If your TV is turned on, check your updated version and
Tool option. (explain the Tool option, next stage)
* If downloading version is more high than your TV have, TV
can lost all channel data. In this case, you have to channel
recover. if all channel data is cleared, you didnt have a
DTV/ATV test on production line.
* After downloading, have to adjust TOOL OPTION again.
1) Push IN-START key in service remote control.
2) Select Tool Option 1 and push OK key.
3) Punch in the number. (Each model has their number.)

- 15 -
EXPLODED VIEW
IMPORTANT SAFETY NOTICE
A23
A21
A2
510
300
511
560
A22
570
120
A5
A10
200
900
910
231
230
210
221
920
810
220
121
LV1
530
540
521
700
400
710
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by
in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
Copyright
LG Electronics. Inc. All rights reserved.
- 16 -
NAND FLASH MEMORY 8Gbit
16Gbit
Strap Setting
Boot ROM Device Select - (FA4,FAD7,FAD2,FAD1)
+3.3V_Normal
+3.3V_Normal
+3.3V_Normal
IC102-*1
TH58DVG4S0ETA20
IC102
TC58DVG3S0ETA00
NC_1
NC_1
2.7K
NC_2
R107
NC_4
NC_5
16Gbit
0
NC_6
RY/BY
NAND_RBb
RE
NAND_REb
CE
NAND_CEb
R148
NAND_CEb2
16Gbit
0
NC_7
NC_8
C102
4700pF
VCC_1
C101
0.1uF
VSS_1
NC_10
CLE
ALE
NAND_ALE
WE
NAND_WEb
WP
+3.3V_Normal
NC_11
4.7K
OPT
- High : Normal Operation

- Low : Write Protection
R103
Write Protection
NC_12
NC_13
FLASH_WP
47
46
45
44
43
42
41
40
10
39
11
38
12
37
13
NC_9
NAND_CLE
48
NC_3
R149
NAND_8Gbit
NC_14
NC_15
0000:
0010:
0100:
0110:
1000:
1010:
CI_ADDR[4]
0001:
NAND_DATA[7] 0011:
NAND_DATA[2] 0101:
0111:
NAND_DATA[1] 1001:
1011:
1100:
1110:
1101,
36
14
35
15
34
16
33
17
32
18
31
19
30
20
29
21
28
22
27
23
26
24
25
NC_28
NC_2
NC_27
NC_3
NC_26
NC_4
NAND_DATA[0-7]
NC_25
I/O8
I/O7
I/O6
I/O5
NC_5
NAND_DATA[7]
RY/BY2
NAND_DATA[6]
RY/BY1
NAND_DATA[5]
RE
NAND_DATA[4]
CE1
NC_24
PSL
CE2
R151
16Gbit
0
NC_6
NC_23
VCC_1
VCC_2 +3.3V_Normal
VSS_2
C104
NC_22
VSS_1
10uF
10V
NC_7
C103
0.1uF
NC_21
NC_8
CLE
NC_20
I/O4
I/O3
I/O2
I/O1
ALE
NAND_DATA[3]
WE
NAND_DATA[2]
WP
NAND_DATA[1]
NC_9
NAND_DATA[0]
NC_10
NC_19
NC_11
NC_18
NC_12
NC_17
NC_13
NC_16
DEV_NAND_16Gbit
48
47
46
45
44
43
42
41
40
10
39
11
38
12
37
13
36
14
35
15
34
16
33
17
32
18
31
19
30
20
29
21
28
22
27
23
26
24
25
R113
10K
R117
10K
OPT
R122
10K
R127
10K
OPT
R114
10K
OPT
R118
10K
R123
10K
OPT
R128
10K
NC_26
NC_25
NC_24
NC_23
I/O8
ST Micro M25P or compatible Serial Flash

8-bit 512Mbit 512B page SLC NAND Flash devices
8-bit 128, 256Mbit 512B page SLC NAND Flash devices
8-bit 1Gbit 2KB page SLC NAND Flash devices
8-bit 2Gbit, 4Gbit, 8Gbit 2KB page SLC NAND Flash devices
8-bit 16Gbit, 32Gbit 4KB page SLC NAND Flash devices (O)
8-bit 8/16/32Gbit 2KB page MLC NAND Flash devices
8-bit 16/32Gbit 4KB page MLC NAND Flash devices
8-bit 32Gbit 8KB page MLC NAND Flash devices
3B dual IO Serial Flash
BB dual IO Serial Flash
fast Serail Flash > 50Mhz
OneNAND Flash (always 16-bit)
Reserved
1111: Reserved
R154
10K
OPT
R157
10K
OPT
R160
10K
OPT
R164
10K
OPT
R167
10K
OPT
R175
10K
OPT
R170
10K
R177
10K
R181
10K
OPT
R179
10K
OPT
R183
10K
R187
10K
OPT
R192
10K
OPT
NAND_DATA[0]
CI_ADDR[7]
NAND_DATA[6]
CI_ADDR[6]
NAND_CLE
NAND_DATA[4]
I/O7
CI_ADDR[9]
I/O6
CI_ADDR[11]
CI_ADDR[12]
I/O5
CI_ADDR[13]
CI_ADDR[8]
NC_22
NAND ECC (FA3, FA2, FALE)
PSL
NAND_DATA[3]
NAND_DATA[5]
+3.3V_Normal
NC_21
R155
10K
R158
10K
R161
10K
R165
10K
R168
10K
R171
10K
OPT
VCC_2
R119
10K
OPT
R115
10K
R111
10K
OPT
VSS_2
CI_ADDR[3]
NC_20
CI_ADDR[2]
NC_19
NAND_ALE
R112
10K
NC_18
R116
10K
OPT
R120
10K
000 = ECC disabled

001 = ECC 1-bit repair
010 = ECC 4-bit BCH (O)
011 = ECC 8-bit BCH, 27 byte spare
110, 111 = Reservedd
NAND_DATA[0]:
0: System is LITTLE endian (O)
1: System is BIG endian
CI_ADDR[7]:
0: Disable EDID automatic Downloading from Flash (O)
1: Enable EDID automatic Downloading from Flash
I/O2
NAND_DATA[6] :
0: Disable OSC clock output on chip Pin (O)
1: Enable OSC clock output on chip pin.
I/O1
DUAL COMPONENT
NC_17
NC_16
IC102
1ST : EAN61000101
CI_ADDR[6]:
0: Host MIPS run at 500 MHz (O)
1: Host MIPS run at 250 MHz
2ND : T-TH58DVG4S0ETA20
NAND_CLE:
0: Differential Oscillators TVM not bypassed (O)
1: Differential Oscillators TVM bypassed
IC102-*1
R193
10K
R188
10K
NAND_DATA[3]:
0: MIPS will boot from external flash (O)
1: MIPS will boot from ROM
NAND_DATA[4]:
0: 27MHz TVM Crystal Frequency
1: 54MHz TVM Crystal Frequency (O)
+3.3V_Normal
R184
10K
OPT
CI_ADDR[8]:
0: RESETOUTb (in On/Off only) stay asserted until software releases them.
1: Fix amount of delay for de-assertion on RESETOUTb (in On/IOff only)
at end of RESETb pulse (O)
NC_15
NC_14
R182
10K
R180
10K
CI_ADDR[9],CI_ADDR[11],CI_ADDR[12],CI_ADDR[13]
TVM Crystal oscillator bias/gain control
0000: 210uA
0001: 390uA
0010: 570uA
0011: 730uA
0100: 890uA (O)
0111: 1290uA
1000: 1416uA
1111: 2196uA
0101, 0110, 1001, 1010, 1011, 1100, 1101, 1110: Reserved
I/O4
I/O3
R178
10K
OPT
R176
10K
NAND_DATA[5]:
0: FLASH MODE (O)
1: BSC_SLAVE(BBS) MODE
BCM_NVM_256K
IC103-*1
AT24C256C-SSHL-T
NVRAM
A0
A1
R196
10K
IC101
LGE35230(BCM35230KFSBG)
A2
+3.3V_Normal
RGB_DDC_SDA
S
B
D
GND
VCC
WP
SCL
SDA
NON_BCM_CAP
HDMI_RX0-
B4
HDMI_RX0+
+3.3V_Normal
R105
4.7K
HDMI_RX1-
R104 R195
4.7K 4.7K
TXOUT0_L1N
HDMI0_D0N
TXOUT0_L1P
HDMI0_D0P
TXOUT0_L2N
TXOUT0_L2P
B3
HDMI0_D1N
TXCLK_LN
HDMI0_D1P
TXCLK_LP
TXOUT0_L3N
A2
HDMI_RX2-
B2
HDMI_RX2+
HDMI0_D2N
TXOUT0_L3P
HDMI0_D2P
TXOUT0_L4N
AF28
AG27
AG28
AE26
AF26
AH27
AG26
AF25
AE25
TXOUT0_L4P
TXB4P
Q101
TXB4N
BSS83
NAND_DATA[0-7]
TXB3N
TXBCLKN
TXB2P
+3.3V_Normal
TXB1P
TXB1N
TXOUT0_U0N
DDC0_SCL
TXOUT0_U0P
DDC0_SDA
TXOUT0_U1N
TXOUT0_U1P
HDMI0_HTPLG_IN
TXOUT0_U2N
HDMI0_HTPLG_OUT
TXOUT0_U2P
TXCLK_UN
D13
HDMI0_ARC
TXCLK_UP
HDMI0_RESREF
R106
3K
FAD_3
V5
LNB_INT
TXB0P
IRRXDA
R198
10K
TXB0N
TXOUT0_U3N
TXOUT0_U3P
TXOUT0_U4N
AG25
AE24
AD24
AH25
AF24
AE23
AD23
AG24
AF23
AC22
AD22
TXOUT0_U4P
AG23
TXOUT1_L0N
TXOUT1_L0P
TXOUT1_L1N
TXOUT1_L1P
TXOUT1_L2N
TXOUT1_L2P
TXCLK1_LN
TXCLK1_LP
TXOUT1_L3N
TXOUT1_L3P
TXOUT1_L4N
AH23
AE22
AE21
AF22
AH22
AG22
AF21
AG21
AF20
AD21
AC21
TXOUT1_L4P
S
B
D
TXA3N
C119
0.1uF
16V
TXACLKN
TXA2P
AG20
TXOUT1_U0P
TXOUT1_U1N
TXOUT1_U1P
TXOUT1_U2N
TXOUT1_U2P
TXCLK1_UN
TXCLK1_UP
TXOUT1_U3N
TXOUT1_U3P
TXOUT1_U4N
AH20
AD19
AE19
AF19
AH19
AE18
AD18
AG19
AF18
AG18
AF17
TXOUT1_U4P
AB5
FCEB_0
SPARE_ADC2
FCEB_1
FCEB_2
FS_IN1
AC2
NAND_DATA[4]
AC3
NAND_DATA[3]
AD2
NAND_DATA[2]
AD3
NAND_DATA[1]
AE2
NAND_DATA[0]
R169
0
TXA1P
U2
VGA_SDA
VGA_SCL
TXA0P
AF1
AC5
AE6
AG5
FWE
FRD
AG2
AE3
AA5
FRDYB
TXA0N
BBS CONNECT
E2
R121
1.2K
+3.3V_Normal
R126
1.2K
R129
1.2K
BCM_RX
R131
1.2K
Y1
R135
R136
SCL0_3.3V
33
AA3
33
AA2
TXD3N
TXDCLKP
1
TXDCLKN
VCC
C106
4.7uF
TXD2P
TXD2N
SCL
TXD0P
R110
1.5K
H2
SDA2_3.3V
R199
22
H5
SDA
TXD0N
GND
C107
33pF
50V
DVB_S
C108
33pF
50V
DVB_S
C110
33pF
50V
C109
33pF
50V
TXC4N
5V_HDMI_2
TXC3P
FOR HDMI STANDARD
APPLY ONLY WHEN CONNECT TO PULL-UP GPIO
TXCCLKP
TXCCLKN
TXC2P
+3.3V_Normal
TXC2N
FA_3
FA_4
RDB/GPIO
FA_5
TDB/GPIO
FA_6
FA_7
TXC1P
FA_8
BSC_S_SDA
FA_9
R142
OPT
R143
OPT
OPT
R145
22
U5
22
U4
22
W3
22
W1
4.7K
R139
+3.3V_Normal
AG16
BL_PWM/GPIO
R194
2.7K
R108
A_DIM
C105
2.2uF
10V
- Low : Normal Operation

- High : Write Protection
SCL
R190
33
SDA
R191
33
54MHz X-TAL
/CI_CE1
/CI_CE2
X-TAL_1
C113
12pF
FLASH_WP
R185
NAND_WEb
50V
NAND_REb
AON_GPIO_36
TDI/GPIO
TDO
TMS/GPIO
AON_RESETOUTB
TCK/GPIO
CI_ADDR[2-14]
AD5
CI_ADDR[3]
AD4
CI_ADDR[4]
AE4
CI_ADDR[5]
AE5
CI_ADDR[6]
AD6
CI_ADDR[7]
AH3
CI_ADDR[8]
AF4
CI_ADDR[9]
AH4
CI_ADDR[10]
AG4
CI_ADDR[11]
AF5
CI_ADDR[12]
AG3
CI_ADDR[13]
AH2
R125
1K
X101-*2
54MHz
1
CI_ADDR[14]
C114
12pF
50V
54MHz_XTAL_N
1
54MHz
X101
X-TAL_1
R189
1M
OPT
R186
0
CRYSTAL_BCM_Sunny
EAW58812611
SUNNY ELECTRONICS CORPORATION
X-TAL_1
X-TAL_2
X101-*1
54MHz
1
GND_1
54MHz_XTAL_P
GND_2
GND_2
X-TAL_2
CRYSTAL_BCM_Lihom
EAW60763703
LIHOM CO., LTD.
+3.3V_Normal
AH5
R146 10K
R147
1K
R150
1K
R153
1K
R156
1K
R159
1K
R162
1K
R166
1K
AF14
AH14
R163
1K
AD14
AG14
AC16
L/R_SYNC_DINT
DINT/GPIO
L/R_SYNC_DINT
Y3
SOC_RESET
SCL3_3.3V
SDA3_3.3V
CRYSTAL_BCM_KDS
EAW58239604
DAISHINKU CORPORATION.
2
GND_1
NAND_CLE
NAND_RBb
CI_ADDR[2]
X-TAL_2
/PCM_WAIT
G24
R124
1K
OPT
10K
VSS
NAND_ALE
SRST
AH16
Write Protection
WP
AD15
TRSTB
TVM_BYPASS
TXC1N
+3.3V_Normal
VCC
NAND_CEb
AC4
AON_HSYNC
AON_GPIO_37
Y6
AE1
FA_15
AB6
R132
FA_14
AON_VSYNC
OPT
TXC0P
FA_12
FA_13
POWER_CTRL
R144
5V_HDMI_4
FA_11
NMIB
W5
5V_HDMI_3
R130
OPT 2K
BSC_S_SCL
FA_10
4.7K F25
R141
5V_HDMI_1
TXC3N
FA_2
BSCCLKA
+3.3V_Normal
PCM_5V_CTL
DVB_S Option: apply EU Satellite model
TXC4P
FA_0
BSCDATAA
H4
22
AF2
FA_1
H3
SCL2_3.3V
R197
TXD1P
TXD1N
R109
1.5K
RDA
TDA
BCM_TX
SDA0_3.3V
TJC2508-4A
NAND_CEb2
Y2
P101
TXD3P
A8h
GND_2
TXD4P
GND_1
NFWPB
U3
+3.3V_Normal
TXA1N
TXD4N
E1
FS_IN2
AH7
RESETB
RESETOUTB
GPIO_BL_ON
NAND_DATA[5]
AF3
AC18
LT0VCAL_MONITOR
AC1
FCEB_3
TXA2N
TXC0N
NAND_DATA[6]
AG1
FALE
SPARE_ADC1
AB2
SC_ID
NAND_DATA[7]
AB3
FAD_0
FP_IN1
Y5
AB1
FP_IN0
AA4
TXACLKP
4
TXOUT1_U0N
Y4
Q102
BSS83
TXA3P
FAD_2
FAD_1
TXA4P
TXA4N
FAD_5
FAD_4
AH26
V3
E6
TVM_XTALOUT
54MHz_XTAL_N
TXB2N
FAD_7
FAD_6
AB4
V4
HDMI_ARC
NON_BCM_CAP
TVM_XTALIN
AF6
RGB_DDC_SCL
CEC
V2
AG6
54MHz_XTAL_P
+3.3V_Normal
IC103
M24M01-HRMN6TP
NC
C118
0.1uF
16V
TXBCLKP
W2
W4
IC101
TXB3P
4.7K
OPT
AF27
4.7K
AE28
R174
TXOUT0_L0P
R173
TXOUT0_L0N
HDMI0_CLKP
A3
HDMI_RX1+
R101
4.7K
HDMI0_CLKN
A4
4.7K
OPT
C5
HDMI_CLK+
BCM_NVM_1M
R172
HDMI_CLK-
AE27
B5
AVS_VSENSE
AVS_RESETB
J6
W6
AVS_VFB
TMODE
AVS_NDRIVE_1
TESTEN
AVS_PDRIVE_1
For L/R sync GPIO
AG7
AD7
SRST
AF7
AH8
+3.3V_Normal
C111
0.01uF
C112
0.1uF
F7
E7
C6
VDAC_VREG
VDAC_1
VDAC_RBIAS
VDAC_2
D7
DTV/MNT_V_OUT
R140
560
1%
BCM REFRENCE is 562ohm
THE
SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE
SYMBOL MARK OF THE SCHEMETIC.

BCM35230
MAIN & NAND FLASH
2010.09.18
1
POWER 2.5V
+2.5V_BCM35230
AADC_AVDD25
ADAC_AVDD25
+2.5V_BCM35230
CORE 0.9V
+3.3V_Normal
C223
0.01uF
IN
OUT
IN
C253
10uF
10V
C249
10uF
10V
NFM18PS105R0J
C204
6.3V
C256
0.1uF
C258
0.1uF
C261
10uF
10V
C247
22uF
OUT
GND
PHM
R257
1K
S_TUNER
R256
1K
T2_TUNER
R255
1K
R254
1K
OLED
R253
1K
FHD
R252
1K
BCM_FRC/URSA5
R251
1K
FRC2/URSA5
R250
1K
NFM18PS105R0J
C233
6.3V
C221
0.1uF
L209
C263
4.7uF
C267
0.1uF
C271
0.01uF
C280
0.1uF
C274
22uF
+0.9V_CORE
C284
22uF
VAFE2_DVDD
L219
BLM18PG121SN1D
C292
22uF
C288
0.1uF
C285
4.7uF
C299
0.1uF
C296
4.7uF
GND
+2.5V_BCM35230
EPHY_VDD25
+2.5V_BCM35230
+0.9V_CORE
NFM18PS105R0J
C244
6.3V
MODEL_OPT_0
L203
BLM18PG121SN1D
+3.3V_Normal
C251
0.1uF
16V
MODEL_OPT_1
C236
0.1uF
C234
0.1uF
C232
4.7uF
10V
MODEL_OPT_2
USB_AVDD
L214
BLM18PG121SN1D
BLM18PG121SN1D
+0.9V_CORE
+0.9V_CORE
C225
0.22uF
6.3V
L205
BLM18PG121SN1D
+0.9V_CORE
HDMI_AVDD
+0.9V_CORE
L202
BLM18PG121SN1D
C238
IN
4.7uF
10V
PLL_AUD_AVDD
+0.9V_CORE
L210
BLM18PG121SN1D
C259
10uF
10V
C255
0.1uF
C252
4.7uF
10V
C260
4.7uF
C262
10uF
C266
4.7uF
C270
0.1uF
C272
0.01uF
VAFE3_DVDD
C277
4.7uF
C281
0.1uF
GND
PLL_MAIN_AVDD
L217
BLM18PG121SN1D
C297
0.1uF
C294
4.7uF
C290
0.1uF
C287
4.7uF
C248
10uF
10V
OUT
+0.9V_CORE
L215
BLM18PG121SN1D
MODEL_OPT_3
MODEL_OPT_4
+2.5V_BCM35230
VAFE2_VDD25
PLL_VAFE_AVDD
L211
BLM18PG121SN1D
L218
BLM18PG121SN1D
C205
10uF
10V
C203
10uF
10V
NO_PHM
R267
1K
NO_S_TUNNER
R266
1K
NO_T2_TUNER
R265
1K
OPT
R264
1K
LCD
R263
1K
HD
R262
1K
MODEL_OPT_7
NO_FRC/FRC2
R261
1K
NO_FRC/BCM_FRC
R260
1K
+0.9V_CORE
L206
BLM18PG121SN1D
+1.5V_DDR
MODEL_OPT_6
PLL_MIPS_AVDD
+0.9V_CORE
MODEL_OPT_5
C207
4.7uF
10V
C211
0.1uF
C209
4.7uF
10V
C213
0.1uF
C215
0.01uF
C220
0.1uF
C222
0.01uF
C265
4.7uF
+2.5V_BCM35230
+2.5V_BCM35230
VAFE3_VDD25
BCM
internal
FRC
NO_FRC
C254
4.7uF
C250
4.7uF
10V
LG FRC2
external
URSA5
MODEL_OPT_0
MODEL_OPT_1
HIGH
C264
4.7uF
1600
MODEL_OPT_5
T2 Tuner
Support
Not Support
MODEL_OPT_6
S Tuner
Support
Not Support
V7
M10
P10
R10
Disable
T10
U10
V10
close to soc
IC101
C217
16V
0.1uF
Non_CHB
W10
V13
L11
100
R241
+3.3V_Normal
IF_P
NON_BCM_CAP
F26
D26
R211
6.04K
EPHY_TDP
EPHY_TDN
EPHY_RDP
EPHY_RDN
E27
E26
C17
EPHY_VREF
VI_IFP0
EPHY_RDAC
VI_IFM0
EPHY_TDP
EPHY_TDN
AGC_SDM_2
EPHY_RDP
E5
R287
10K
WIFI
R210
4.87K
1%
SIDE_USB_DM
SIDE_USB_DP
SIDE_USB_CTL1
GPIO_1
USB_MONCDR
GPIO_2
USB_RREF
GPIO_3
2K
IF_AGC
0.01uF
R233
1.2K
C16
G28
3D_SYNC
G26
NON_NTP
C227
33pF
50V
W11
R234
1.2K
V14
SDA1_3.3V
L18
SCL1_3.3V
M18
N18
C231
33pF NON_NTP
50V
P18
R18
C2
D1
T18
USB_PORT1DN
W14
USB_PORT1DP
PCI_VIO_0
PCI_VIO_1
D2
USB_PWRFLT_1/GPIO
U18
W15
V18
W13
W18
PCI_VIO_2
V15
USB_PWRON_1/GPIO
B1
J5
USB_PORT2DN
GPIO_4
USB_PORT2DP
GPIO_5
GPIO_6
C4
USB_PWRFLT_2/GPIO
USB_PWRON_2/GPIO
GPIO_7
GPIO_70
PCM_TS_DATA[0-7]
PCM_TS_CLK
PCM_TS_DATA[0]
OPT
0
L5
PCM_TS_DATA[1]
M5
PCM_TS_DATA[2]
L6
PCM_TS_DATA[3]
N3
PCM_TS_DATA[4]
N1
PCM_TS_DATA[5]
N2
PCM_TS_DATA[6]
M3
PCM_TS_DATA[7]
M2
PCM_TS_SYNC
PCM_TS_VAL
F/NIM_EU_CN
R202
TU_TS_CLK
0
FE_TS_DATA[0]
GPIO_72
M4
L4
N4
TCLKA/GPIO
GPIO_73
TDATA_0/GPIO
GPIO_74
TDATA_1/GPIO
GPIO_75
TDATA_2/GPIO
GPIO_76
TDATA_3/GPIO
GPIO_77
TDATA_4/GPIO
GPIO_78
TDATA_5/GPIO
GPIO_79
K5
FE_TS_DATA[3] R205
0 F/NIM_EU_CN
F/NIM_EU_CN
0
0 F/NIM_EU_CN
FE_TS_DATA[4] R206
FE_TS_DATA[5] R207
F/NIM_EU_CN
K1
FE_TS_DATA[6] R208
F/NIM_EU_CN
K3
FE_TS_DATA[7] R209
F/NIM_EU_CN
L1
FE_TS_DATA[1] R203
FE_TS_DATA[2] R204
F/NIM_EU_CN
CHBO_TS_CLK
TU_TS_SYNC
CHBO_TS_SERIAL
TS_VAL_ERR
J2
J3
K2
L3
L2
TDATA_7/GPIO
PCM_MCLKI
PCI_AD05
TVLDA/GPIO
PCI_AD06
PCI_AD07
TCLKD/GPIO
PCI_AD08
TDATD_0/GPIO
PCI_AD09/GPIO
TDATD_1/GPIO
PCI_AD10/GPIO
TDATD_2/GPIO
PCI_AD11/GPIO
TDATD_3/GPIO
PCI_AD12/GPIO
TDATD_4/GPIO
PCI_AD13/GPIO
TDATD_5/GPIO
PCI_AD14/GPIO
TDATD_6/GPIO
PCI_AD15/GPIO
TDATD_7/GPIO
PCI_AD16/GPIO
TSTRTD/GPIO
PCI_AD17/GPIO
TVLDD/GPIO
PCI_AD18/GPIO
T2
PCM_MDI[1]
R3
PCM_MDI[2]
R2
PCM_MDI[3]
P3
PCM_MDI[4]
P2
PCM_MDI[5]
P1
PCM_MDI[6]
R6
N5
PCM_MDI[7]
PCM_MISTRT
PCM_MIVAL_ERR
PCI_AD20/GPIO
P4
PCM_MDI[0]
T4
P5
MPEG_CLK/GPIO
PCI_AD21/GPIO
MPEG_D_0/GPIO
PCI_AD22
MPEG_D_1/GPIO
PCI_AD23
MPEG_D_2/GPIO
PCI_AD24
MPEG_D_3/GPIO
PCI_AD25
MPEG_D_5/GPIO
PCI_CBE00
MPEG_D_6/GPIO
PCI_CBE01/GPIO
MPEG_D_7/GPIO
PCI_CBE02/GPIO
MPEG_SYNC/GPIO
/PCM_IRQA
T5
EPHY_ACTIVITY
T19
AE15
AF15
AG15
R214
AF16
AE16
R215
R281
R282
AG17
R216
U19
EPHY_LINK
22
DTV_ATV_SELECT
22
22
22
+3.3V_Normal
R240
2.7K
V16
V17
Place Cap
Very close to R22 Ball
MODEL_OPT_3
R228
AE17
22
VDAC_AVDD33
MLG1005S22NJT
MCIF_RESET/GPIO
MCIF_SCLK/GPIO
MCIF_SCTL/GPIO
AC15
AB12
AB11
SC_DET/COMP2_DET
AG13
AH13
AF13
TW9910_RESET
AE13
AD12
C224
1uF
25V
OPT
C226
0.1uF
16V
OPT
R218
22
RF_BOOSTER_CTL
AG10
PCM_RST
R220
22
AA28
V28
R28
M28
J28
K23
M22
T22
FRC_RESET
T23
U22
Place Cap
Very close to R22 Ball
PCI_IRDYB/GPIO
PCI_PAR/GPIO
PCI_PERRB/GPIO
MCIF_SDI/GPIO
PCI_REQ1B
MCIF_SDO/GPIO
PCI_SERRB/GPIO
PCI_TRDYB/GPIO
VDDC_5
VSS_5
VDDC_6
VSS_6
VDDC_7
VSS_7
VDDC_8
VSS_8
VDDC_9
VSS_9
VDDC_10
VSS_10
VDDC_11
VSS_11
VDDC_12
VSS_12
VDDC_13
VSS_13
VDDC_14
VSS_14
VDDC_15
VSS_15
VDDC_16
VSS_16
VDDC_17
VSS_17
VDDC_18
VSS_18
VDDC_19
VSS_19
VDDC_20
VSS_20
VDDC_21
VSS_21
VDDC_22
VSS_22
VDDC_23
VSS_23
VDDC_24
VSS_24
VDDC_25
VSS_25
VDDC_26
VSS_26
VDDC_27
VSS_27
VDDC_28
VSS_28
VDDC_29
VSS_29
VDDC_30
VSS_30
VDDC_31
VSS_31
VDDC_32
VSS_32
VDDC_33
VSS_33
VDDC_34
VSS_34
VDDC_35
VSS_35
VDDC_36
VSS_36
VDDC_37
VSS_37
VDDC_38
VSS_38
VDDC_39
VSS_39
VDDC_40
VSS_40
VDDC_41
VSS_41
VDDC_42
VSS_42
VSS_43
Y22
VDDR1_1
VSS_47
VDDR1_2
VSS_48
VDDR1_3
VSS_49
VDDR1_4
VSS_50
VDDR1_5
VSS_51
VDDR1_6
VSS_52
VDDR1_7
VSS_53
VDDR1_8
VSS_54
VDDR1_9
VSS_55
VDDR1_10
VSS_56
VDDR1_11
VSS_57
VDDR1_12
VSS_58
VSS_59
R22
R221
22
BCM_L/DIM
L/DIM0_MOSI
H22
AE8
R222
22
BCM_L/DIM
L/DIM0_SCLK
G23
AB9
AC11
K7
AC8
AB15
AB8
L7
M7
R283
22
N6
COMP1_DET
P6
MODEL_OPT_5
AB7
VSS_62
G15
AE9
AC10
VSS_60
VSS_61
+3.3V_Normal
DD_MREMOTE
VSS_44
VSS_46
DDR_LDO_VDDO
DC_MREMOTE
AD10
AH10
VSS_4
MODEL_OPT_4
AE10
AG12
VSS_3
VDDC_4
VSS_45
C242
0.1uF
DSUB_DET
VSS_2
VDDC_3
L22
URSA_RESET
AV2_CVBS_DET
AF12
AF10
R231-*1
FRC2_RESET
R231
100
CHB_RESET
VDDC_2
POR_VDD
+3.3V_Normal
AE14
VSS_1
L/DIM0_VS
L220
+0.9V_CORE
VDDR3_1
VSS_63
VDDR3_2
VSS_64
VDDR3_3
VSS_65
VDDR3_4
VSS_66
VDDR3_5
VSS_67
VDDR3_6
VSS_68
VDDR3_7
VSS_69
VDDR3_8
VSS_70
VDDR3_9
VSS_71
VDDR3_10
VSS_72
VDDR3_11
VSS_73
VSS_74
AD11
R223
R284
22
22
AE11
R224
22
AD13
AE12
R235
AC12
R225
AC13
AH11
R226
R285
AF11
R227
100
0 OPT
22
22
22
3D_GPIO_0
+3.3V_Normal
MODEL_OPT_6
AA7
Y7
ERROR_OUT
RF_SWITCH_CTL
3D_GPIO_1
3D_GPIO_2
VSS_75
AA6
MODEL_OPT_7
AON_VDDC_1
VSS_76
AON_VDDC_2
VSS_77
AON_POR_VDD
VSS_78
VSS_79
U7
AON_VDDR3
VSS_80
VSS_81
T7
T6
L213
BLM18PG121SN1D
K10
VDDC_1
L10
PWM_DIM
R230
22
BCM_L/DIM
INSTANT_MODE
W19
+1.5V_DDR
MODEL_OPT_1
MODEL_OPT_2
22
AD17
V19
RF_SWITCH_CTL_2
AH17
AG11
PCI_STOPB/GPIO
THE
M_RFModule_RESET
R19
PCI_CBE03
PCI_FRAMEB/GPIO
R4
T1
P19
AC14
PCI_DEVSELB/GPIO
T3
H6
CI_DET
AB14
MPEG_D_4/GPIO
MPEG_DATA_EN/GPIO
U1
N19
MODEL_OPT_0
V6
AD16
M19
M_REMOTE_RX
AB13
TSTRTA/GPIO
PCI_AD19/GPIO
PCM_MDI[0-7]
R280
22
TDATA_6/GPIO
K6
J4
R5
FRC2_RESET
C1
GPIO_71

R213
V11
4.7K
R232-*1
SIDE_USB_CTL2
CHBO_TS_SYNC
A16
U11
+3.3V_Normal
C3
SIDE_USB_OCD2
CHBO_TS_VAL_ERR
T11
C229
0.1uF
4.7K
R232
URSA_RESET
WIFI_DM
WIFI_DP
FE_TS_DATA[0-7]
closed to soc
L19
R286
10K
WIFI
R201
R11
IF_N
+3.3V_Normal
B16
C216
E1
SIDE_USB_OCD1
P11
BLM18PG121SN1D
A15
F5
C201
100pF
OPT
N11
L201
D15
AGC_SDM_1
EPHY_RDN
GPIO_0
+3.3V_Normal
B17
M11
VDDR_AGC
F27
F28
R212
C218
1K
100
0.1uF R242
16V
C293
0.1uF
C291
4.7uF
IC101
N10
Enable
L216
BLM18PG121SN1D
+3.3V_Normal
LCD
1333
HDMI_AVDD33
+3.3V_Normal
C283
0.1uF
V12
PHM
USB_AVDD33
L212
BLM18PG121SN1D
NON_BCM_CAP
OLED
DDR speed
C298
0.1uF
POWER 3.3V
HD
MODEL_OPT_4
MODEL_OPT_7
C268
0.1uF
+3.3V_Normal
+0.9V_CORE
MODEL_OPT_3
C295
4.7uF
C282
0.1uF
PLL_VAFE_AVDD25
C257
0.1uF
LOW
FHD
MODEL_OPT_2
C279
4.7uF
L207
BLM18PG121SN1D
L204
BLM18PG121SN1D
MODEL OPTION
C269
0.1uF
AON_VDDR10_1
VSS_82
AON_VDDR10_2
VSS_83
K11
K12
C289
0.1uF
C286
4.7uF
L12
M12
N12
P12
R12
T12
U12
W12
K13
L13
IC101
M13
N13
AADC_AVDD25
P13
NON_BCM_CAP
R13
F19
T13
F20
AADC_AVDD25
ADAC_AVDD25
AADC_AVSS
U13
D25
W16
D24
K14
E24
L14
EPHY_VDD25
G22
ADACA_AVDD25
ADACA_AVSS
ADACC_AVDD25
ADACC_AVSS
ADACD_AVDD25
ADACD_AVSS
G21
F22
M14
F24
N14
E25
P14
F23
EPHY_BVDD25
EPHY_AVSS
EPHY_AVDD25
R14
HDMI_AVDD
T14
U14
HDMI_AVDD33
D5
K15
D4
L15
+2.5V_BCM35230
F6
HDMI0_AVDD
HDMI0_AVSS_1
HDMI0_AVDD33
HDMI0_AVSS_2
G6
M15
AE20
N15
AD20
P15
AC20
R15
+2.5V_BCM35230
AB20
T15
AB22
LT0VDD25_1
LT0VSS_1
LT0VDD25_2
LT0VSS_2
LT0VDD25_3
LT0VSS_3
LT0VDD25_4
LT0VSS_4
U15
LT0VSS_5
C275
0.1uF
OPT
K16
L16
LT0VSS_6
AB21
AB19
AC19
AB18
AB17
AC17
LT0VSS_7
M16
USB_AVDD
N16
P16
D14
USB_AVDD33
E4
R16
D3
VDAC_AVDD33
T16
SPDIF_IN_AVDD25
SPDIF_IN_AVSS
F15
G7
USB_AVDD
USB_AVSS_1
USB_AVDD33
USB_AVSS_2
G8
U16
D6
VAFE2_DVDD
K17
E17
Place as close as possible to the pad
C212
390pF
50V
P17
VAFE3_DVDD
R17
C214
390pF
50V
D16
D17
D8
use only for A0/B0 chip
K19
AB16
C210-*1
220pF
50V
BCM_A0/B0
R7
M6
AB23
P7
W7
J7
VAFE2_AVDD25_2 VAFE2_VSS_3
VAFE2_VSS_4
VAFE2_VSS_5
D9
W17
G14
VAFE2_VSS_1
VAFE2_DVDD25
U17
H7
G20
VAFE2_DVDD
VAFE3_VDD25
T17
K18
VDAC_AVSS
D18
M17
N17
G9
VDAC_AVDD33
VAFE2_VDD25
L17
C208
390pF
50V
E8
C210
390pF
50V
BCM_C0
F9
E9
F8
PLL_AUD_AVDD
PLL_MAIN_AVDD
G25
PLL_MIPS_AVDD
K4
PLL_VAFE_AVDD
AD25
D11
PLL_VAFE_AVDD25
D12
+0.9V_CORE
VAFE3_DVDD
VAFE2_VSS_6
E18
G18
G17
F18
G16
F16
VAFE3_AVDD25_2
G13
VAFE3_DVDD25
VAFE3_VSS_2
POR_VDD25
VAFE3_VSS_3
VAFE3_VSS_4
VAFE3_VSS_5
PLL_AUD_AVDD
G12
F12
G11
G10
F10
VAFE3_VSS_6
PLL_MAIN_AVDD
PLL_MIPS_AVDD
PLL_MIPS_AVSS
PLL_VAFE_AVDD
PLL_VAFE_AVDD25
AD26
N7
AE7
AB10
AC6
G19
AC7
TVM_OSC_AVDD
AC23
C202
390pF
50V
C206
390pF
50V
C273
0.1uF
C276 +3.3V_Normal
U6
0.01uF
OPT
TVM_OSC_AVSS
AUX_AVDD33
AA22
C278
0.1uF
J23
J22
K22
J25
N22
N23
M25
P22
R25
V22
W22
W23
V25
AA25
VSS_84
BCM35230
MAIN POWER
50
DSUB_R+
INCM_R
C320
0.1uF
C321
0.1uF
R311
36
IC101
DSUB_G+
C327
0.1uF
INCM_G
C328
0.1uF
NON_BCM_CAP
B6
R317
36
A6
C7
A7
DSUB_B+
C322
0.1uF
B7
INCM_B
C323
0.1uF
C8
VI_R
VI_INCM_R
VI_G
BCM35230_with_CAP_220pF
VI_INCM_G
VI_B
VI_INCM_B
R312
36
DSUB_HSYNC
DSUB_VSYNC
IC101-*1
LGE35230
C13
A13
HSYNC_IN
VSYNC_IN
COMP1_Y
0.1uF
C9
C330
0.1uF
A9
C331
0.1uF
B9
C332
0.1uF
B8
C333
0.1uF
C11
C334
0.1uF
A10
C335
0.1uF
B10
C336
0.1uF
C10
C329
COMP1_Pr
COMP1_Pb
B6
BCM_CAP
A6
VI_PR1
C7
VI_PB1
A7
VI_INCM_COMP1
VI_SC_R1
Near P801
Run Along DSUB_R Trace
Near P801
Run Along DSUB_G Trace
B7
INCM_R
C8
INCM_G
C13
VI_SC_B1
A13
Run Along DSUB_B Trace
Near P801
F13
VI_FB_1/GPIO
VI_FS1
A12
SC_R/COMP2_Pr
C12
SC_G/COMP2_Y
B12
SC_B/COMP2_Pb
B11
VI_SC_R2
Near JK1101
Run Along COMP_Y_IN,COMP_Pr_IN,COMP_Pb_IN Trace
Near JK1104
Run Along AV2_CVBS Trace
VI_G
VI_INCM_G
VI_B
Near TU2101/2
TU2201/2/3
Run Along TUNER_CVBS_IF_P Trace
HSYNC_IN
C9
INCM_VID_COMP1
A9
B9
INCM_VID_AV2
B8
VI_Y1
VI_PR1
VI_PB1
VI_INCM_COMP1
VI_SC_G2
VI_SC_B2
VI_INCM_SC2
VI_FB_2/GPIO
Near
VI_FS2
INCM_TUNER
INCM_VID_AV1
Run Along COMP_Y_IN,COMP_Pr_IN,COMP_Pb_IN/SC R,G,B Trace
JK1103
JK2501
C11
A10
Run Along AV1_CVBS Trace
Near JK1102
E12
E14
VI_INCM_R
VSYNC_IN
INCM_B
D10
SC_FB
VI_R
VI_INCM_B
VI_SC_G1
VI_INCM_SC1
INCM_VID_COMP1
R310
0
VIDEO INCM
VI_Y1
B10
C10
VI_SC_R1
VI_SC_G1
VI_SC_B1
VI_INCM_SC1
INCM_VID_SC/COMP2
D10
E15
INCM_VID_SC/COMP2
F17
R318
0
AV2_CVBS_IN
C303
0.1uF
INCM_VID_AV2
C304
0.1uF
E16
INCM_VID_SC
E11
10
INCM_TUNER
R306
75
1%
OPT
C317
0.1uF
C318
0.1uF
C325
0.1uF
C326
0.1uF
A18
C19
R316
36
A19
B19
C20
B20
C12
VI_C1_2
B12
C319
E10
F11
0.1uF
R305
240
OPT
VI_CVBS2
VI_FS2
E15
VI_CVBS3
F17
VI_INCM_CVBS3
E16
VI_CVBS4
F14
VI_INCM_LC1_1
VI_C1_2
VI_INCM_LC1_2
B18
VI_SIF1_2
A18
C19
A19
R319
10K
OPT
C20
R320
12K
OPT
E19
B20
VI_CVBS1
VI_INCM_CVBS1
VI_CVBS2
VI_INCM_CVBS2
VI_CVBS3
VI_INCM_CVBS3
VI_CVBS4
VI_INCM_CVBS4
0.1uF
R315
120
OPT
VI_C1_1
C18
VI_INCM_SIF1_1
+2.5V_BCM35230
C324
VI_L1
VI_SIF1_1
B19
INCM_SIF
VI_FB_2/GPIO
VI_INCM_CVBS2
VI_INCM_SIF1_2
R314
12K
VI_SC_B2
VI_INCM_SC2
E14
E19
D19
VI_SC_G2
E12
VI_INCM_CVBS1
E11
R313
10K
VI_SC_R2
VI_CVBS1
VI_INCM_CVBS4
+2.5V_BCM35230
R304
36
TU_SIF
VI_FS1
A12
VI_INCM_LC1_1
VI_INCM_LC1_2
B18
VI_FB_1/GPIO
VI_C1_1
C18
NON_EU
R325
0
EU
R325-*1
INCM_VID_AV1
F14
VI_L1
B11
R303
36 TU_CVBS
AV1_CVBS_IN
SC_CVBS_IN
F13
D19
E10
F11
VI_SIF1_1
VI_INCM_SIF1_1
VI_SIF1_2
VI_INCM_SIF1_2
IC101
NON_BCM_CAP
B15
C15
+3.3V_Normal
SPDIF_INC_P
I2SSCK_OUTA/GPIO
SPDIF_INC_N
I2SWS_OUTA/GPIO
I2SSD_OUTA0/GPIO
C14
B14
R301
1.2K
R302
1.2K
SPDIF_IND_P
I2SSOSCK_OUTA/GPIO
SPDIF_IND_N
I2SSD_OUTA1/GPIO
M_REMOTE_TX
F4
G5
SDA3_3.3V
I2SSCK_IN/GPIO
I2SWS_IN
I2SSD_IN/GPIO
C301
33pF
50V
C302
33pF
50V
PC_L_IN
C305
1uF 10V
C25
C306
1uF 10V
B24
INCM_AUD_PC
C307
1uF 10V
A24
I2SWS_OUTC/GPIO
C308
1uF 10V
E22
AV1_R_IN
C309
1uF 10V
E23
INCM_AUD_AV1
C310
1uF 10V
D23
AV2_L_IN
C311
1uF 10V
C24
AV2_R_IN
C312
1uF 10V
C23
INCM_AUD_AV2
C313
1uF 10V
B23
SC/COMP2_L_IN
C314
1uF 10V
E21
SC/COMP2_R_IN
C315
1uF 10V
D21
INCM_AUD_SC/COMP2
C316
1uF 10V
D22
AADC_LINE_R1
I2SWS_OUTD/GPIO
I2SSD_OUTD/GPIO
AADC_LINE_R3
E3
F3
AUD_SCK
100
TU_RESET_SUB
AUD_LRCK
AUD_LRCH
AUD_MASTER_CLK
C337
22pF
OPT
C338
22pF
OPT
C339
22pF
OPT
C340
33pF
OPT
HP_DET
AV1_CVBS_DET
TU_RESET
G3
G1
H1
SC_RE1
SC_RE2
AUDIO INCM
/RST_HUB
S2_RESET
AUDMUTE_1
AADC_LINE_L4
ADAC_AL_N
R321
Route Between AV1_L_IN & AV1_R_IN Trace
R322
Route Between SC/COMP2_L_IN & SC/COMP2_R_IN Trace
Near JK1104
R323
Route Between AV2_L_IN & AV2_R_IN Trace
Near JK801
R324
Route Between PC_L_IN & PC_R_IN Trace
Near JK1102
AADC_LINE_R4
ADAC_AL_P
C27
D28
ADAC_AR_N
D27
ADAC_AR_P
AADC_LINE_R5
C26
ADAC_CL_N
A27
ADAC_CL_P
AADC_LINE_L6
B27
AADC_LINE_R6
ADAC_CR_N
AADC_INCM6
ADAC_CR_P
Near
E13
C28
AADC_LINE_L5
SPDIF_OUT
AG8
A21
B21
F2
B13
AUDMUTE_0/GPIO
AADC_INCM3
AADC_INCM5
C21
AD9
SPDIF_OUTA/GPIO
AADC_LINE_L3
F21
E20
100
AD8
100
AADC_LINE_R2
AADC_INCM4
D20
R329
AADC_LINE_L2 I2SSOSCK_OUTD/GPIO
B22
A22
100
AC9
G2
I2SSCK_OUTD/GPIO
AADC_INCM2
C22
R328
I2SSOSCK_OUTC/GPIO
AADC_LINE_L1
AADC_INCM1
AV1_L_IN
PHONE JACK
R327
AG9
E2
I2SSCK_OUTC/GPIO
I2SSD_OUTC/GPIO
PC_R_IN
R326
AF9
I2SSD_OUTA2/GPIO
G4
SCL3_3.3V
AF8
B28
JK1103
JK2501
INCM_AUD_AV1
INCM_AUD_SC/COMP2
INCM_AUD_AV2
HP_LOUT_N
HP_LOUT_P
INCM_AUD_PC
HP_ROUT_N
HP_ROUT_P
SCART1_Lout_N
Near TU2101/2
TU2201/2/3
Route Along With TUNER_SIF_IF_N
INCM_SIF
SCART1_Lout_P
SCART1_Rout_N
SCART1_Rout_P
B25
AADC_LINE_L7
ADAC_DL_N
AADC_LINE_R7
ADAC_DL_P
AADC_INCM7
A25
A26
ADAC_DR_N
B26
ADAC_DR_P
THE

BCM35230
MAIN AUDIO/VIDEO
50
DUAL COMPONENT
IC401,IC402
IC401-*1
IC402-*1
1ST : EAN61667501, 2ND : EAN61570701

1ST : T-K4B2G1646B_HCK0, 2ND : T-H5TQ2G63BFR-PBC
DDR STRAP
DDR_DQ[0]
DDR_DQ[1]
DDR_DQ[2]
DDR_DQ[3]
DDR_DQ[4]
R401
4.7K
R403
4.7K
DDR_1333
R407
4.7K
R405
4.7K
R409
4.7K
OPT
+1.5V_DDR
+1.5V_DDR
NFM18PS105R0J
NFM18PS105R0J
C410
6.3V
JEDEC Types : DDR_DQ[0:4]

00001 : DDR3-1333H (CasL=9)
10101 : DDR3-1600K (CasL=11) (O)
C403
2.2uF
DDR_1333
C405
10uF
C407
2.2uF
IN
C432
6.3V
C417
470pF
OUT
C423
10uF
C421
2.2uF
C425
10uF
IN
GND
DDR_DQ[10]
+1.5V_DDR
DDR_DQ[9]
DDR_DQ[7]
DDR_DQ[8]
IN
DDR_DQ[5]
R432
4.7K
OPT
R404
4.7K
OPT
R406
4.7K
OPT
R408
4.7K
R410
4.7K
OPT
+1.5V_DDR
NFM18PS105R0J
C402
6.3V
+1.5V_DDR
DDR_DQ[6]
R402
4.7K
OPT
OUT
GND
NFM18PS105R0J
C433
6.3V
C412
1uF
OUT
IN
GND
C453
1uF
6.3V
Bus Width : DDR_DQ[10]

0 - 16b
1 - 32b (O)
Chip Width : DDR_DQ[8]
0 - 8b
1 - 16b (O)
Chip Size : DDR_DQ[6:5]
00 - 4Gbit
01 - 2Gbit (O)
10 - 1Gbit
11 - 512Mbit
C454
1uF
6.3V
C426
1uF
OUT
GND
C455
1uF
6.3V
+1.5V_DDR
+1.5V_DDR
+1.5V_DDR
IC401
K4B2G1646C
IC402
K4B2G1646C
R416
4.99K
1%
R422
4.99K
1%
R430
4.7K
OPT
R429
82
DDR_RESETb
P7
DDR_AA1
P3
DDR_AA2
DDR_DQ[0-7]
DDR_DQ[8-15]
DDR_DQ[16-23]
DDR_DQ[24-31]
U26
DDR_DQ[1]
R26
DDR_DQ[2]
U27
DDR_DQ[3]
R27
DDR_DQ[4]
V27
DDR_DQ[5]
P26
DDR_DQ[6]
U25
DDR_DQ[7]
P27
DDR_DQ[8]
R24
DDR_DQ[9]
N24
DDR_DQ[10]
T25
DDR_DQ[11]
M23
DDR_DQ[12]
R23
DDR_DQ[13]
N25
DDR_DQ[14]
T24
DDR_DQ[15]
N26
DDR_DQ[16]
L26
DDR_DQ[17]
H27
DDR_DQ[18]
L27
DDR_DQ[19]
J26
DDR_DQ[20]
M27
DDR_DQ[21]
G27
DDR_DQ[22]
M26
DDR_DQ[23]
H26
DDR_DQ[24]
L23
DDR_DQ[25]
H25
DDR_DQ[26]
L24
DDR_DQ[27]
J24
DDR_DQ[28]
M24
DDR_DQ[29]
H23
DDR_DQ[30]
L25
DDR_DQ[31]
H24
DDR_ADA_0
DDR_DQA_1
DDR_ADA_1
DDR_DQA_2
DDR_ADA_2
DDR_DQA_3
DDR_ADA_3
Y23
Y26
DDR_ADA_4
DDR_DQA_6
DDR_ADA_5
DDR_DQA_7
DDR_ADA_6
Y24
AC26
DDR_DQA_8
DDR_ADA_ALT_4
DDR_DQA_10
DDR_ADA_ALT_5
DDR_DQA_11
DDR_ADA_ALT_6
DDR_ADA_7
DDR_DQA_14
DDR_ADA_8
DDR_DQA_15
DDR_ADA_9
DDR_DQA_16
DDR_ADA_10
DDR_DQA_17
DDR_ADA_11
DDR_DQA_18
DDR_ADA_12
DDR_DQA_19
DDR_ADA_13
Y25
DDR_BAA_1
DDR_DQA_24
DDR_BAA_2
AA27
AC27
AA26
DDR_RASA_N
DDR_DQA_27
DDR_CASA_N
DDR_DQA_28
AD27
DDR_DQA_30
DDR_DM[0]
T26
DDR_DM[1]
P25
DDR_DM[2]
J27
DDR_DM[3]
K24
U24
W28
DDR_QS0b
DDR_QS1
DDR_QS1b
DDR_QS2
DDR_QS2b
DDR_QS3
DDR_QS3b
T28
P23
W26 R411
DDR_ZQ
P24
DDR01_CLK
DDR_AA11
DDR01_CLKb
M3
K9
R414
DDR_RASb
DDR_CASb
DDR_BAA2
DDR_WEb
DDR_RASb
DDR_RESETb
K1
J3
K3
L3
VDD_2
VDD_3
A12/BC
VDD_4
DDR_QS0b
DDR_QS1
DDR_QS1b
DDR_DM[0]
DDR_DM[1]
DDR_DQ[0-7]
240
VDD_8
DDR_DQ[8-15]
B7
VDDQ_2
CK
VDDQ_3
CKE
VDDQ_4
VDDQ_5
CS
VDDQ_6
ODT
VDDQ_7
RAS
VDDQ_8
CAS
VDDQ_9
D3
E3
DDR_DQ[1]
F7
DDR_DQ[2]
F2
DDR_DQ[3]
F8
DDR_DQ[4]
H3
DDR_DQ[5]
H8
DDR_DQ[6]
G2
DDR_DQ[7]
H7
DDR_DQSA_P_3
DDR_DQSA_N_3
DDR_DQ[12]
C2
DDR_DQ[9]
A7
DDR_DQ[10]
A2
DDR_1333_NANYA
VSS_1
DQSU
VSS_2
VSS_3
DML
VSS_4
DMU
VSS_5
VSS_6
DQL0
VSS_7
DQL1
VSS_8
DQL2
VSS_9
DQL3
VSS_10
DQL4
VSS_11
P7
P3
N2
P8
P2
R8
R2
T8
R3
L7
R7
N7
T3
A0
A3
VREFDQ
P2
A5
A6
L8
ZQ
T8
A8
A9
VDD_1
A10/AP
VDD_2
A11
VDD_3
A12
VDD_4
NC_6
VDD_5
VDD_6
NC_5
VDD_7
BA0
VDD_9
VDD_8
K9
J3
K3
L3
D9
L7
G7
CK
N7
K8
T3
VDDQ_2
CK
VDDQ_3
VDDQ_4
VDDQ_5
CS
VDDQ_6
ODT
VDDQ_7
RAS
VDDQ_8
RESET
NC_4
F3
DQSL
A8
J7
K7
C9
K9
D2
E9
L2
F1
K1
H2
J3
H9
K3
J9
DQSU
DML
DMU
F2
F8
H3
H8
G2
H7
VSS_1
VSS_2
VSS_4
VSS_5
VSS_6
E3
F7
DQL0
VSS_7
DQL1
VSS_8
DQL2
VSS_9
DQL3
VSS_10
DQL4
VSS_11
DQL5
VSS_12
C8
C2
A7
A2
B8
A3
VDD_2
VDD_3
A12
VDD_4
VDD_5
VDD_6
NC_5
VDD_7
BA0
VDD_9
VDD_8
B2
R3
D9
L7
G7
R7
K2
N7
K8
T3
N9
VDDQ_2
VDDQ_3
CKE
VDDQ_4
VDDQ_5
VDDQ_6
ODT
VDDQ_7
RAS
VDDQ_8
CAS
VDDQ_9
DQSL
A9
C7
B3
B7
DQSU
E1
G8
E7
J2
D3
J7
K7
C9
K9
L2
F1
K1
H2
J3
H9
K3
L3
M1
E3
M9
F7
P1
F2
P9
F8
T1
H3
T9
H8
DQU1
VSSQ_3
DQU2
VSSQ_4
DQU3
VSSQ_5
DQU4
VSSQ_6
DQU5
VSSQ_7
DQU6
VSSQ_8
DQU7
VSSQ_9
B9
J9
VSS_1
VSS_2
VSS_4
VSS_5
VSS_6
VSS_7
DQL1
VSS_8
DQL2
VSS_9
DQL3
VSS_10
DQL4
VSS_11
C3
D8
C8
E2
C2
E8
A7
F9
A2
G1
B8
A3
THE
A11
VDD_3
A12
VDD_4
NC_6
VDD_5
VDD_6
NC_5
VDD_7
BA0
VDD_9
VDD_8
D9
G7
K2
K8
N1
N9
VDDQ_2
CK
VDDQ_3
CKE
VDDQ_4
VDDQ_5
CS
VDDQ_6
ODT
VDDQ_7
RAS
VDDQ_8
CAS
VDDQ_9
R9
C7
A8
C1
C9
DQSU
G8
E7
J2
F1
H2
H9
J9
D3
DML
DMU
M1
E3
M9
F7
P1
F2
P9
F8
T1
H3
T9
H8
VSS_12
G2
H7
VSS_1
VSS_2
VSS_4
VSS_5
VSS_7
DQL1
VSS_8
VSS_9
DQL3
VSS_10
DQL4
VSS_11
DQL5
VSS_12
VSSQ_1
VSSQ_2
DQU1
VSSQ_3
DQU2
VSSQ_4
DQU3
VSSQ_5
DQU4
VSSQ_6
DQU5
VSSQ_7
DQU6
VSSQ_8
DQU7
VSSQ_9
B9
D7
D1
C3
D8
C8
E2
C2
E8
A7
F9
A2
G1
B8
G9
A3
A3
H1
VREFDQ
A10/AP
VDD_2
A11
VDD_3
A12/BC
VDD_4
A13
VDD_5
VDD_6
NC_5
DDR_BAA0
A8
DDR23_CLK
N8
M3
C1
DDR23_CLKb
C9
BA0
E9
F1
R419
56
1%
C419
1000pF
H2
H9
K9
DDR_CKE
R420
DDR_RASb
DDR_CASb
10K
K1
J3
K3
L3
J9
DDR_RESETb
CK
VDDQ_2
CK
VDDQ_3
CKE
VDDQ_4
VDDQ_5
CS
VDDQ_6
ODT
VDDQ_7
RAS
VDDQ_8
CAS
VDDQ_9
WE
RESET
L9
DDR_QS2
DDR_QS3
B3
DDR_QS3b
DQSL
G8
DDR_DM[2]
DDR_DQ[16-23]
DDR_DM[3]
VSSQ_2
VSS_1
DQSU
VSS_2
VSS_3
E7
D3
M1
DDR_DQ[16]
E3
M9
DDR_DQ[17]
F7
P1
DDR_DQ[18]
F2
P9
DDR_DQ[19]
F8
T1
DDR_DQ[20]
H3
T9
DDR_DQ[21]
H8
DDR_DQ[22]
G2
DDR_DQ[23]
H7
DML
VSS_4
DMU
VSS_5
VSS_6
DQL0
VSS_7
DQL1
VSS_8
DQL2
VSS_9
DQL3
VSS_10
DQL4
VSS_11
DQL5
VSS_12
DQU1
VSSQ_3
DQU2
VSSQ_4
DQU3
VSSQ_5
VSSQ_6
DQU5
VSSQ_7
DQU6
VSSQ_8
VSSQ_9
D7
D1
DDR_DQ[30]
C3
D8
DDR_DQ[29]
C8
E2
DDR_DQ[28]
C2
E8
DDR_DQ[25]
A7
F9
DDR_DQ[26]
A2
DDR_DQ[31]
B8
G1
G9
DDR_DQ[27]
N1
DDR_AA11
N9
DDR_AA3
R1
DDR_AA7
A1
DDR_AA0
A8
DDR_AA1
C1
DDR_BAA0
C9
DDR_BAA2
D2
DDR_BAA1
E9
DDR_AA10
F1
DDR_AA12
A3
DDR23_AA6
DDR01_AA6
L9
T7
A9
VDD_2
A12
VDD_4
VDD_5
VDD_6
VSSQ_3
VSSQ_4
DQU3
VSSQ_5
DQU4
VSSQ_6
VSSQ_7
DQU6
VSSQ_8
DQU7
VSSQ_9
VDD_7
VDD_8
BA0
T1
B9
N2
P8
VDDQ_1
VDDQ_2
P2
R8
D1
R2
D8
R3
T8
L7
E2
R7
E8
T3
N7
CK
VDDQ_3
K3
VDDQ_4
VDDQ_5
L2
J3
CS
VDDQ_6
ODT
VDDQ_7
RAS
VDDQ_8
CAS
VDDQ_9
F9
M7
G1
M2
G9
M3
N8
NC_2
NC_3
NC_4
F3
DQSL
C1
C9
D2
E9
F1
H9
J9
L1
L9
T7
NC_7
E1
G8
J2
M1
M9
P1
D3
P9
T1
T9
F7
F8
H3
H8
G2
H7
B1
VSSQ_1
DQU0
VSSQ_2
DQU1
VSSQ_3
DQU2
VSSQ_4
DQU3
VSSQ_5
DQU4
VSSQ_6
DQU5
VSSQ_7
DQU6
VSSQ_8
DQU7
VSSQ_9
B9
D1
D8
E2
E8
F9
G1
G9
VSS_1
DQSU
VSS_2
DML
VSS_4
DMU
VSS_5
DQL0
VSS_7
DQL1
VSS_8
VSS_3
VSS_6
E3
F2
DQL2
VSS_9
DQL3
VSS_10
DQL4
VSS_11
DQL5
VSS_12
C2
A7
A2
B8
A3
56
C452
0.1uF
DDR_CASb
R426
56
DDR_RASb
R427
56
C441
1uF
A6
L8
ZQ
B2
VDD_1
A10/AP
VDD_2
A11
VDD_3
A12/BC
VDD_4
VDD_5
VDD_6
NC_5
VDD_7
BA0
VDD_9
VDD_8
J3
G7
K2
K8
N1
N9
R1
R9
A1
VDDQ_2
CK
VDDQ_3
CKE
VDDQ_4
VDDQ_5
CS
VDDQ_6
ODT
VDDQ_7
RAS
VDDQ_8
CAS
VDDQ_9
A8
C1
C9
D2
E9
F1
H2
H9
R2
R3
L7
R7
N7
T3
NC_2
J9
L9
T7
DQSU
F7
F2
F8
H3
H8
G2
H7
VSS_1
VSS_2
VSS_3
DML
VSS_4
VSS_5
VSS_6
DQL0
VSS_7
DQL1
VSS_8
DQL2
VSS_9
DQL3
VSS_10
DQL4
VSS_11
DQL5
C2
A7
A2
B8
E1
G8
J2
J8
M1
M9
P1
P9
T1
T9
VSS_12
A8
B2
A9
VDD_1
A10/AP
VDD_2
A11
VDD_3
A12/BC
VDD_4
A13
VDD_5
VDD_6
VDD_7
VDD_8
M2
BA0
K7
K9
K1
K3
L3
VDDQ_2
VDDQ_3
CKE
VDDQ_4
CS
VDDQ_6
ODT
VDDQ_7
VDDQ_5
RAS
VDDQ_8
CAS
VDDQ_9
VSSQ_1
VSSQ_2
DQU1
VSSQ_3
DQU2
VSSQ_4
DQU3
VSSQ_5
DQU4
VSSQ_6
DQU5
VSSQ_7
DQU6
VSSQ_8
DQU7
VSSQ_9
N1
N9
R1
R9
RESET
NC_2
NC_3
NC_4
F3
DQSL
A8
C1
C9
D2
E9
F1
H2
H9
J1
NC_1
J9
L1
L9
T7
NC_6
A9
C7
B7
DQSU
VSS_1
DQSU
VSS_2
VSS_3
E7
D3
DML
VSS_4
DMU
VSS_5
VSS_6
E3
F7
F2
F8
H3
H8
G2
DQL0
VSS_7
DQL1
VSS_8
DQL2
VSS_9
DQL3
VSS_10
DQL4
VSS_11
DQL5
VSS_12
B9
D1
D8
E2
E8
F9
G1
G9
C8
C2
A7
A2
B8
A3
E1
G8
J2
J8
M1
M9
P1
P9
T1
T9
B1
VSSQ_1
D7
C3
B3
DQL6
DQL7
B1
DQU0
K8
A1
CK
CK
T2
G3
K2
VDD_9
VDDQ_1
L2
J3
D9
G7
BA1
J7
H7
DQL7
C8
B3
DQL6
D7
L8
ZQ
A7
DQSL
A9
E7
D3
A5
A6
L1
NC_6
C7
DQSU
H1
VREFDQ
A4
NC_5
DQSL
B7
A2
A3
M7
N8
M8
VREFCA
A1
WE
J1
NC_1
DQSL
R8
A0
BA2
VDDQ_1
F3
P8
M3
WE
G3
D9
BA1
CK
N2
T8
A8
A9
P7
P2
A7
DDR_1600_SS
N3
DQU0
VSSQ_2
DQU1
VSSQ_3
DQU2
VSSQ_4
DQU3
VSSQ_5
DQU4
VSSQ_6
DQU5
VSSQ_7
DQU6
VSSQ_8
DQU7
VSSQ_9
B9
D1
D8
E2
E8
F9
G1
G9
B3
E1
G8
J2
J8
M1
M9
P1
P9
T1
T9
B1
VSSQ_1
D7
C3
AR406
DQL6
DQL7
C8
1uF
A9
DQSU
E7
J8
0.1uF
56
C440
P3
H1
VREFDQ
A5
J7
A3
C7
B7
A3
A4
BA2
H2
J1
NC_1
RESET
VREFCA
A2
A13
C3
WE
T2
L9
B3
A0
DMU
A8
0.1uF
IC402-*1
K4B2G1646C-HCK0
M8
A1
E3
CK
CKE
K1
DDR_1600_SS
BA1
A1
AR405
IC401-*1
K4B2G1646C-HCK0
T9
N9
VDD_9
0.1uF
C451
P9
K2
R9
C409
56
P1
NC_3
R1
AR404
0.1uF
1uF
M9
P3
VSSQ_2
C439
M1
NC_4
N1
0.1uF
J8
B2
K8
C450
C408
J2
D9
G7
56
G8
RESET
VDD_3
AR403
E1
T2
A10/AP
0.1uF
B3
L8
A11
C406
DDR01_AA5
ZQ
VDD_1
56
DDR01_AA4
DDR_AA14
L3
A7
AR402
DDR23_AA5
L1
A4
A8
0.1uF
DDR23_AA4
J9
A5
A6
1uF
C404
C411
H9
P7
DQU2
DQU5
C438
DDR_WEb
H2
B1
VSSQ_1
DQU1
OPT
56
DDR_AA9
DQL6
DQU0
AR401
R9
N3
DQL7
DDR_DQ[24]
B9
K8
A9
DQSU
B1
VSSQ_1
56
DDR_AA2
DQSL
B7
J8
DDR_DQ[24-31]
56
R425
NC_6
C7
E1
J2
NC_2
NC_4
F3
G3
R424
DDR_AA14
K2
J1
NC_1
T2
NC_3
DDR_AA14
DDR_AA13
G7
DDR_AA8
VDDQ_1
L1
T7
D9
BA1
L2
+1.5V_DDR
R431
4.7K
OPT
+1.5V_DDR
VDD_9
BA2
K7
R418
56
1%
D2
VDD_7
VDD_8
J7
VSS_12
DQU0
DQU7
VDD_1
M2
C437
100pF
B2
A9
M7
DDR_CKE
K3
T7
DQL6
DQL7
DQU0
A3
A8
DDR_VREFA
240
1%
A7
R1
R9
ZQ
R421
K9
DQSL
DQL2
B1
K7
K9
G3
VSS_6
DQL0
DDR_DQ[11]
A6
N1
N9
C436
0.01uF
L8
K1
J7
L1
NC_7
VSS_3
J8
B8
A5
VREFCA
BA2
D2
E9
A9
E1
DDR_DQ[15]
T3
VREFDQ
A4
C442
100pF
R428
82
A1
NC_5
J1
NC_2
NC_4
DQSU
DDR_AA13
N7
A3
H1
A2
M2
L3
NC_1
DQSL
K8
R7
A2
R423
4.99K
1%
L2
M7
R1
A1
VDDQ_1
CK
DDR_AA12
L7
C435
0.01uF
M8
A0
NC_6
BA2
F3
B7
N7
T3
N8
NC_3
A9
R7
M3
RESET
B3
R3
L7
BA1
T2
G3
DQL6
D7
VDD_1
DQSL
DQL0
DQL5
T8
B2
VDD_2
L9
T7
R8
R2
A9
L1
NC_7
DQL7
D1
G9
DML
ZQ
A10/AP
D2
E9
P2
L8
A8
J1
NC_2
VSS_3
DMU
J8
H7
VSSQ_2
DQSU
A6
N2
P8
WE
NC_1
F3
A8
C1
VREFDQ
A7
M2
N8
P3
H1
A5
A1
CK
CS
A3
DDR_1600_NANYA
N3
P7
A4
R1
R9
VREFCA
A2
M7
M3
VDDQ_1
CK
A0
A1
N1
BA1
NC_3
B1
DQU0

A10/AP
A11
NC_4
G2
VSSQ_1
D7
VDD_1
L9
DQL6
DQL7
C3
R2
T8
A8
A9
R8
DQSL
VSS_3
E7
D3
ZQ
A7
RESET
G3
P8
L8
T7
NC_7
C7
DQSU
A6
N2
P2
A5
T2
L1
DQSL
B7
VREFDQ
WE
J1
NC_2
NC_3
A3
BA2
L3
NC_1
T2
P3
H1
M8
N3
P7
A4
M2
C1
VDDQ_9
VREFCA
A2
M7
R1
R9
A0
A1
NC_6
N1
N9
A1
CKE
CAS
R7
K2
N8
WE
G3
R3
M3
VDDQ_1
L2
K1
B2
BA1
J7
R8
R2
A7
BA2
K7
N2
P8
A4
M2
M3
P3
H1
M8
N3
P7
A2
M7
N8
VREFCA
A1
K2
DQL6
DQU4
R3
M8
VREFCA
K7
DDR_1600_NANYA
DDR_1333_NANYA
M8
N3
DDR_AA11
DDR_QS2b
DQSU
D7
C8
IC402-*3
NT5CB128M16BP-DI
DDR_AA10
G7
NC_6
DQL7
C3
IC402-*2
NT5CB128M16BP-CG
D9
A9
DQL5
T8
DDR_AA9
DDR_1333_SS
A1
J1
NC_2
NC_4
DQSL
R2
DDR_AA7
DDR_WEb
NC_1
E7
DDR_DQ[13]
IC401-*3
NT5CB128M16BP-DI
+1.5V_DDR
DQSL
DDR_DQ[14]
K25
DDR23_AA6
DDR_BAA2
C7
DDR_DQ[0]
DDR_DQ[8]
DDR_DQSA_N_2
240
R8
DDR_BAA1
WE
G3
P2
A0
A1
CK
F3
P8
DDR23_AA4
VDD_9
VDDQ_1
RESET
N2
DDR_AA3
DDR_VREFA
BA1
DDR_DQSA_P_2
IC401-*2
NT5CB128M16BP-CG
VDD_7
NC_3
1%
DDR_DQSA_P_1
VDD_5
VDD_6
T2
P3
DDR_AA8
A11
L2
10K
R415
1%
A10/AP
BA0
P7
DDR_AA1
B2
VDD_1
BA2
+1.5V_DDR
DDR_DQSA_N_1
K26
N8
ZQ
A9
M2
N3
DDR_AA0
R417
4.99K
1%
DDR23_AA5
A8
A13
DDR_CKE
R413
56
1%
C401
1000pF
K27
K28
T3
K7
R412
56
1%
DDR_RESETb
DDR_RST_N
DDR_DQSA_N_0
N7
C416
0.01uF
L8
A7
J7
DDR_VREFA
AA23
DDR_DQSA_P_0
DDR_AA10
DDR23_CLKb
U23
T27
DDR_BAA2
DDR23_CLK
N27
DDR_VREFA
DDR_QS0
DDR_BAA1
DDR_AA8
DDR01_CLKb
N28
DDR_DMA_3
DDR_AA7
DDR01_CLK
DDR_CKA01_N
DDR_CKA23_N
R7
A6
NC_5
DDR_CKE
W27
DDR_CKA23_P
L7
VREFDQ
A5
M7
DDR_QS0
DDR_CKEA
DDR_DMA_2
R3
H1
A4
DDR_WEb
DDR_WEA_N
DDR_DMA_1
T8
A3
DDR_CASb
V26
DDR_DMA_0
DDR_AA12
DDR_BAA1
W25
DDR_CKA01_P
DDR01_AA6
DDR_BAA0
W24
DDR_DQA_31
DDR_DM[0-3]
DDR_AA11
DDR_AA14
AB28
DDR_DQA_29
DDR_AA10
DDR01_AA5
DDR_AA13
V24
DDR_DQA_26
DDR01_AA4
DDR_AA12
AA24
DDR_DQA_25
R2
C415
0.01uF
DDR_AA2
A2
DDR_AA9
Y27
DDR_BAA_0
DDR_DQA_23
DDR_AA8
DDR_BAA0
DDR_ADA_14
DDR_DQA_22
DDR_AA7
M8
VREFCA
A1
DDR23_AA6
AD28
DDR_DQA_21
DDR_AA2
DDR_AA3
DDR23_AA5
AC24
AB25
DDR_DQA_13
DDR01_AA6
A0
DDR23_AA4
AC25
DDR_DQA_12
DDR_AA1
R8
DDR_AA13
AB24
DDR_DQA_9
P2
DDR01_AA5
DDR_AA9
AB26
DDR_DQA_5
DDR_DQA_20
DDR_AA0
AB27
DDR_DQA_4
P8
DDR01_AA4
V23
DDR_DQA_0
N2
DDR_AA3
NON_BCM_CAP
DDR_DQ[0]
DDR_1333_SS
N3
DDR_AA0
IC101
DQU0
VSSQ_2
DQU1
VSSQ_3
DQU2
VSSQ_4
DQU3
VSSQ_5
DQU4
VSSQ_6
DQU5
VSSQ_7
DQU6
VSSQ_8
DQU7
VSSQ_9
B9
D1
D8
E2
E8
F9
G1
G9
BCM35230
MAIN DDR
50
FLMD0
NEC MICOM
GND
47K
R639
MICOM_DOWNLOAD
0
+3.5V_ST
MICOM_RESET
22
R617
22
32.768KHz
NEC_ISP_Tx
R642
10Mhz Crystal
+3.5V_ST
4.7M
OPT
NEC_ISP_Rx
47K
R615
WIRELESS_PWR_EN
X602
WIRELESS_DET
C607
15pF
15pF
C606
+3.5V_ST
P601
12505WS-12A00
MICOM_RESET
X601
10MHz
For Debug
R641
OPT
C603
50V
13pF
R637
C602
50V
13pF
10K
+3.5V_ST
OCD1A
REGC
P121/X1/OCD0A
P122/X2/EXCLK/OCD0B
FLMD0
P123/XT1
P124/XT2/EXCLKS
RESET
P40
P41
P120/INTP0/EXLVI
46
45
44
43
42
41
40
39
38
37
+3.5V_ST
SCL2_3.3V
SDA2_3.3V
P60/SCL0
36
P140/PCL/INTP6
P61/SDA0
35
P00/TI000
P62/EXSCL0
34
P01/TI010/TO00
P63
33
P130
32
P20/ANI0
31
ANI1/P21
30
ANI2/P22
22
P33/TI51/TO51/INTP4
P75
HDMI_CEC
POWER_ON/OFF2_1
IC601
P74
AMP_MUTE
R632
22
29
ANI3/P23
28
ANI4/P24
R619
P71/KR1
10
27
ANI5/P25
P70/KR0
11
26
ANI6/P26
P32/INTP3/OCD1B
12
25
ANI7/P27
MODEL1_OPT_1
EEPROM_SCL
R633
22
22
VSS
SDA
OCD1B
R616
R649
EDID_WP
C
Q601
2SC3052
OPT
POWER_ON/OFF1
MICOM_DOWNLOAD
SIDE_HP_MUTE
KEY2
KEY1
OPT
EEPROM_SDA
13
22
S/T_SCL
24
SCL
23
INV_CTL
NC/E2
22
WC
10K
MODEL1_OPT_3
21
R648
MODEL1_OPT_2
20
NEC_MICOM
SCART_MUTE
P72/KR2
SOC_RESET
NC/E1
RL_ON
P73/KR3
MODEL1_OPT_0
VCC
uPD78F0514
19
IC602
15
R601
47K
NC/E0
270K
OPT
22
R631
M24C16-WMN6T
20K
1/16W
1%
22
EEPROM_SDA
+3.5V_ST
R630
EEPROM_SCL
EEPROM for Micom
R647
R629
18
NEC_ISP_Rx
NEC_ISP_Tx
14
10K
R626 4.7K
10K
R610
R628 4.7K
R607
1/16W
1%
C605
C604
0.1uF
R645
10K
16
R606
13
C608
0.1uF
16V
SW1
JTP-1127WEM
R646
20K
12
22
FLMD0
17
22
0.1uF
R621
11
R643
GND
+3.5V_ST
10
R644
VSS
47
OCD1B
48
VDD
11YEAR_TOOL
(11 SENSOR)
MODEL_OPT_1
11
I2C_LED
PWM_LED
MODEL_OPT_2
30
TOUCH_KEY
TACT_KEY
MODEL_OPT_3
31
PDP/3D
LCD/OLED
LCD
PDP
OLED
3D
AVSS
AVREF
P12/SO10
P13/TXD6
P14/RXD6
P15/TOH0
+3.5V_ST
C609 1uF
10YEAR_TOOL
(10 SENSOR)
P10/SCK10/TXD0
LOW
P11/SL10/RXD0
HIGH
MODEL_OPT_0
P16/TOH1/INTP5
MICOM MODEL OPTION
PIN NO.
P30/INTP1
MODEL OPTION
PIN NAME
P17/TI50/TO50
P31/INTP2/OCD1A
R627
4.7K
+3.5V_ST
10K
OPT
I2C LED
R622
10K
MODEL1_OPT_1
22
MODEL_OPT_3
+3.5V_ST
MODEL1_OPT_2
THE

NEC_TXD
NEC_RXD
NEC_ISP_Tx
1
POWER_ON/OFF2_2
NEC_ISP_Rx
IR
LED_R/BUZZ
MODEL_OPT_2
R636
4.7K
LED_B/LG_LOGO
R640
HIGH
POWER_DET
TBD
OCD1A
LOW_SMALL
S/T_SDA
LOW
MODEL_OPT_1
R638
MODEL1_OPT_3
PWM_LED
R623
10K
100
100
LCD/OLED
R612
10K
R602
R603
MODEL1_OPT_0
11YEAR_TOOL
R625
10K
100
100
10YEAR_TOOL
R624
10K
PDP/3D
R611
10K
PANEL_CTL
INSTANT_MODE
R604
R605
TACT_KEY
R614
10K
AMP_RESET_N
TOUCH_KEY
R613
10K
+3.5V_ST
BCM35230
MICOM
50
DUAL COMPONENT
D707,D708
D710,D711
1ST : 0DD184009AA
D713
1ST : T-BAT54_SUZHO, 2ND : 0DSON00138A
2ND : 0DSIH00028A
BODY_SHIELD
5V_HDMI_1
BODY_SHIELD
5V_HDMI_4
GND
HDMI_HPD_4
HDMI_HPD_1
20
20
HP_DET
R737
0
5V
R730
3.6K
OPT
GND
17
DDC_DATA
VR703
10V
OPT
OPT
C714
0.1uF
16V
OPT
18
17
GND
DDC_DATA
16
DDC_SCL_1
15
CEC_REMOTE
13
CKCK-_HDMI1
ARC
CK_GND
11
10
CK+
CK+_HDMI1
D0-
R775
C730
0.1uF
150
D0-_HDMI1
D0_GND
R776
63.4
D0+
12
HDMI_ARC
EAG62611201
12
11
10
9
8
7
D0+_HDMI1
D1-
D1-_HDMI1
D1_GND
D1+
D1+_HDMI1
D2-
D2-_HDMI1
D2_GND
D2+
VR707
10V
OPT
OPT
C717
0.1uF
16V
OPT
R729
1K
OPT
* HDMI CEC
DDC_CLK
DDC_SCL_4
NC
14
CE_REMOTE
13
R735
3.6K
OPT
15
ARC
EAG62611201
5V
DDC_CLK
14
R727
0
DDC_SDA_4
DDC_SDA_1
16
VR708
10V
OPT
HP_DET
19
D2+_HDMI1
CE_REMOTE
CEC_REMOTE
+3.3V_Normal
CK-
+3.3V_HDMI
+3.5V_ST
CK-_HDMI4
CK_GND
L701
BLM18PG121SN1D
CK+
CK+_HDMI4
D0D0-_HDMI4
R754
27K
D0_GND
C720
0.1uF
16V
18
R728
1K
OPT
D0+
C719
10uF
C718
10uF
D0+_HDMI4
D1D1-_HDMI4
D
B
S
19
VR706
10V
OPT
D713
D1_GND
BAT54_SUZHO
R741
120K
Q710
BSS83
D1+
D1+_HDMI4
D2-
CEC_REMOTE
D2-_HDMI4
HDMI_CEC
D2_GND
D2+
D2+_HDMI4
RSD-105156-100
JK703
JK704
RSD-105156-100
HDMI1
HDMI4
+3.3V_HDMI
CK+
CK+_HDMI2
D0-
+5V_Normal
5V_HDMI_3
D2-_HDMI2
HDMI_HPD_3
HP_DET
R731
0
5V
GND
DDC_DATA
R739
3.6K
OPT
VR702
10V
OPT
OPT
C716
0.1uF
16V
OPT
VR705
10V
OPT
R726
1K
OPT
D0+_HDMI3
D1-_HDMI3
D1+_HDMI3
VCC33_1
HDMI_RX2+
HDMI_RX1+
HDMI_RX2-
HDMI_RX1-
HDMI_RX0+
HDMI_RX0-
HDMI_CLK+
HDMI_CLK-
CK-_HDMI1
CK+_HDMI1
D0-_HDMI1
D0+_HDMI1
D1-_HDMI1
TPWR_CI2CA
TX2P
TX2N
TX1P
TX1N
TX0P
TX0N
TXCP
TXCN
VCC33_3
R0XCN
R0XCP
55
56
57
58
59
60
61
62
63
64
65
66
67
SCL3_3.3V
+5V_Normal
R706
C710
0
1uF
10V
5V_HDMI_4
R717
10
46
R3PWR5V
RSVD_1
10
45
CBUS_HPD3
R2XCN
11
44
DSCL3
HDMI_HPD_4
C705
DDC_SCL_4
R2XCP
12
43
DSDA3
R2X0N
13
42
R2PWR5V
R2X0P
14
41
R2X1N
15
40
CBUS_HPD2
DSCL2
R2X1P
16
39
R2X2N
17
38
SBVCC
R2X2P
18
37
MICOM_VCC33
1uF
DDC_SDA_4
1/16W
R711
1K
5V_HDMI_3
1%
R718
10
HDMI_HPD_3
C702
1uF
DDC_SCL_3
DSDA2
1/16W
R705
1K
1%
DDC_SDA_3
C708
1uF
R1PWR5V
CBUS_HPD1
DSCL1
DSDA1
R0PWR5V
DSCL0
DSDA0
D0_GND
CBUS_HPD0
D0-_HDMI3
RSVD_2
D0-
VCC33_2
CK+_HDMI3
R3X2P
CK+
R3X2N
CK-_HDMI3
CK_GND
R3X1P
CK5V_HDMI_2
R712
10
C709
D0+
1uF
D0+_HDMI3
D1-
1/16W
R707
1K
1%
D1-_HDMI3
D1_GND
5V_HDMI_1
D1+
R708
10
D1+_HDMI3
D2D2-_HDMI3
D2_GND
C704
1uF
D2+
JK702
RSD-105156-100
HDMI3
1/16W
R703
1K
1%
HDMI_HPD_2
D2+_HDMI3
DDC_SCL_2
47
DSDA4
DDC_SDA_2
3
2
DSCL4
DDC_SCL_1
48
IC701
SII9287B
HDMI_HPD_1
6
5
R1X2P
DDC_SDA_1
R1X2N
D2+_HDMI4
R4PWR5V
D2-_HDMI4
D2+_HDMI3
CEC_REMOTE
49
D1+_HDMI4
11
10
NC
CE_REMOTE
R3X1N
EAG62611201
12
DDC_SCL_3
CEC_A
R1X1P
D1-_HDMI4
13
D2-_HDMI3
CEC_D
50
D0+_HDMI4
14
DDC_CLK
51
R3X0P
15
CK+_HDMI3
D0-_HDMI3
DDC_SDA_3
16
SDA1_3.3V
R779
33
36
CK-_HDMI3
20
SCL1_3.3V
OPT R781 33
SDA3_3.3V
35
BODY_SHIELD
INT
34
HDMI3
CSDA
52
R1X1N
33
D2+_HDMI2
CSCL
53
R1X0P
32
D2-_HDMI2
54
31
D1+_HDMI2
5V_HDMI_3
OPT R780 33
R778
33
R1X0N
30
D1-_HDMI2
THERMAL
73
29
D0+_HDMI2
28
EDID Pull-up
R1XCP
27
D0-_HDMI2
HDMI2
R1XCN
26
CK-_HDMI2
25
HDMI2
DDC_SCL_3
68
DDC_SCL_4
24
D2+_HDMI2
R777
4.7K
DDC_SDA_4
DDC_SDA_3
D2+
23
D2_GND
R724
4.7K
R0X0N
R721
4.7K
4.7K
R0X0P
R716
69
R714
4.7K
22
D1+_HDMI2
D2-
70
D1+
JK701
17
D1+_HDMI1
D711
R0X1N
D708
D1-_HDMI2
21
D0+_HDMI2
D1D1_GND
R0X1P
D0+
R0X2N
D0_GND
RSD-105156-100
18
D2-_HDMI1
+5V_Normal
5V_HDMI_4
D0-_HDMI2
CK+_HDMI2
19
D2+_HDMI1
C
CEC_REMOTE
CK-_HDMI2
CK_GND
D0-_HDMI4
CE_REMOTE
CK-
R3X0N
DDC_SCL_2
CK+_HDMI4
DDC_SCL_1
NC
R0X2P
DDC_SDA_2
DDC_SCL_2
DDC_CLK
71
DDC_SDA_1
20
4.7K
DDC_SDA_2
R3XCP
R723
4.7K
CK-_HDMI4
R720
4.7K
[EP]GND
R715
72
11
10
R713
4.7K
19
EAG62611201
12
C715
0.1uF
16V
OPT
HDMI S/W OUTPUT
HDMI1
C712
0.1uF
16V
R3XCN
13
OPT
C703
0.1uF
16V
C713
0.1uF
16V
A1
14
VR701
10V
OPT
A2
15
DDC_DATA
R740
3.6K
OPT
C701
10uF
10V
C711
0.1uF
16V
16
GND
A1
17
A2
18
R725
0
5V
C706
10uF
10V
C707
10uF
10V
D710
D707
R736
1K
OPT
19
VR704
10V
OPT
HDMI_HPD_2
20
HP_DET
A2
5V_HDMI_2
A1
A2
BODY_SHIELD
A1
+5V_Normal
5V_HDMI_2
+5V_Normal
5V_HDMI_1
HDMI4
THE

BCM35230
HDMI
31
RGB/ PC AUDIO/ SPDIF/ EARPHONE/ RS232C

DUAL COMPONENT
EARPHON JACK
+5V_Normal
RGB PC
D810
KDS184
A2
D804,D805,D806
D807,D808,D813
D814
1ST : EAH39491601, 2ND : EAH33945901
D810
1ST : 0DD184009AA, 2ND : 0DSIH00028A
Q801
1ST : 0TRIY80001A, 2ND : 0TR387500AA
IC805
1ST : EAN61151201, 2ND : EAN61130001
C
A1
JK803
KJA-PH-0-0177
+3.3V_Normal
+5V_Normal
IC801
74F08D
D0A
DSUB_VSYNC
22
R801
22
R802
D0B
14
13
12
A0
D3B
A1
Q0
DSUB_HSYNC
D3A
A2
R850
D1A
OPT
R851 0
D1B
11
10
D2B
R852 0
D2A
OPT
R853 0
OPT
VCC
HP_DET
DETECT
1K
HP_LOUT
R821
WP
EDID_WP
R848
SCL
HP_ROUT
22
RGB_DDC_SCL
R847
SDA
EAG61030001
22
RGB_DDC_SDA
C809
18pF
50V
OPT
GND
2.7K
Q3
GND
Q1
R817
10K
R815
2.7K
2.7K
AT24C02BN-SH-T
VCC
GND
R822
R814
IC802
R825
OPT
0
SPK_R+_HOTEL
C810
18pF
50V
R826
OPT
0
SPK_R-_HOTEL
Q2
R807
10K
OPT
D804
30V
C807
22pF
50V
R808
10K
OPT
D805
30V
C808
22pF
50V
D809
5.6V
OPT
+3.3V_Normal
EARPHONE AMP
D811
L803
120-ohm
BLM18PG121SN1D
5.6V
OPT
LPF READEY
(For H/P Noise Improvement)
DSUB_DET
INR+
C819
1uF
10V
INR-
HP_ROUT_N
EN
10
EAN60724701
6
G0
R827
4.7K
VDD
SGND
IC804
TPA6132A2
R842
4.7K
C
CPP
PGND
Q801
2SC3052
C826
2.2uF
10V
R844
1K
SIDE_HP_MUTE
CPN
L805
BG2012B080TF
R869
0
R828
OPT
OPT
R843
0
HP_ROUT
C823
2.2uF
10V
15
10
11
HPVDD
R837
100K
OPT
C825
2.2uF
10V
C829
0.22uF
10V
16
5
10
4
9
3
8
2
7
1
16
15
14
14
13
13
12
12
11
11
Closed to JACK
12
ESD_CERADIODE
+3.3V_Normal
13
D812-*1
5.6V
R824
OPT
D812
5.6V
HP_ROUT_P
R820
R823
4.7K
ESD_COMMON
ESD_COMMON
D807
30V
5.6V
L808
D807-*1
C832
47pF
50V
ESD_CERADIODE
BLM15BD121SN1
R813
75
INL+
C818
1uF
10V
HP_LOUT_P
1K
DSUB_R+
INL-
C817
1uF
10V
14
HPVSS
HP_LOUT_N
R819
10K
15
G1
+3.3V_Normal
ESD_COMMON
D806
30V
16
OUTR
5.6V
L807
D806-*1
C831
47pF
50V
R811
75
ESD_CERADIODE
DSUB_G+
C816
1uF
10V
HP_LOUT
C828
0.22uF
10V
C821
1uF
10V
Close to the IC
BLM15BD121SN1
L804
BG2012B080TF
R868
0
ESD_COMMON
D808
30V
OUTL
5.6V
C830
47pF
50V
R812
75
C824
0.1uF
16V
C822
10uF
10V
L806
D808-*1
DSUB_B+
ESD_CERADIODE
BLM15BD121SN1
RS232C
JK804
10
SLIM-15F-D-2
5
9
0
R838
4
IR_OUT
IR_OUT
PC AUDIO
100
R804
470K
C804
560pF
50V
C801
560pF
50V
C812
C1+
0.1uF
C813
V+
0.1uF
C814
0.1uF
C1R867
22
PC_R_IN
D802
AMOTECH
5.6V
ESD_COMMON
C2+
16
15
14
13
12
11
VCC
GND
DOUT1
30V
ESD_COMMON
PC_L_IN
D813
D814-*1
ESD_COMMON
MAX3232CDR
R866
22
D801
DETECT
AMOTECH
5.6V
ESD_COMMON
R
R834
2
D814
6
30V
1
5.6V
ESD_CERADIODE
IC803
D813-*1
JP810
5.6V
ESD_CERADIODE
4
3
7
100
GND
+3.5V_ST
JK801
KJA-PH-0-0177
5
8
JP809
R833
SPG09-DB-009
JK805
RIN1
+3.5V_ST
R805
470K
C805
560pF
50V
C802
560pF
50V
C2-
0.1uF
C815
V-
DOUT2
R803
0
SPDIF_OUT
D803
30V
OPT
C803
0.1uF
16V
THE

R860
4.7K
R861
OPT
OPT
4.7K
DIN2
R862
0
ROUT2
BCM_RX
R863
0
EAN41348201
VIN
VCC
GND
NEC_RXD
Fiber Optic
R806
2.7K
RIN2
10
DIN1
R864
0
BCM_TX
R865
0
NEC_TXD
4
SHIELD
SPDIF OUT
JK802
2F11TC1-EM52-4F
+3.3V_Normal
ROUT1
BCM35230
COMMON JACK
2010.10.21
8
58
DUAL COMPONENT
Q901,Q902,Q903
Q904,Q905,Q906
1ST : 0TRIY80001A
D903,D904
D905,D906
1ST : EAH42720601, 2ND : EAH60994401
2ND : 0TR387500AA
+3.5V_ST
IR & KEY
IR_15P
IR_12P
R933
100
EEPROM_SCL
R920
10K
1%
R919
10K
1%
Q901
2SC3052
C
B
E
R908
47K
D901
5.6V
AMOTECH
GND
KEY1
KEY2
5
L901
BLM18PG121SN1D
3.5V
C902
0.1uF
16V
OPT
R902
0
C904
0.1uF
16V
OPT
C905
1000pF
50V
R928
1.5K
GND
LED_B/LG_LOGO
LED_B/LOGO
OPT
IR
COMMERCIAL
C911
100pF
50V
+3.3V_Normal
L902
BLM18PG121SN1D
+3.5V_ST
D907
5.6V
AMOTECH
COMMERCIAL
C
3.3V
11
C912
0.1uF
16V
ESD_ATSC
R917
47K
R913 COMMERCIAL
10K
IR_OUT
GND
10
+3.5V_ST
R911
47K
R906 COMMERCIAL_EU
22
Q903
2SC3052
COMMERCIAL_EU
+3.5V_ST
R909
3.3K
OPT
B
Q902
2SC3052
D906
CDS3C05HDMI1
5.6V
C903
0.1uF
+3.5V_ST
R905
47K
R904
10K
EEPROM_SDA
D902
5.6V
AMOTECH
KEY2
C901
0.1uF
IR
R934
100
EEPROM_SDA
R916
100
+3.5V_ST
EEPROM_SCL
KEY1
R903
47K
P901
12507WR-15L
D905
CDS3C05HDMI1
5.6V
R915
100
+3.5V_ST
P902
12507WR-12L
C913
0.1uF
16V
ESD_ATSC
R929
LED_R/BUZZ
LED_R/BUZZ
12
10
11
12
1.5K
13
GND
13
B
E
COMMERCIAL_EU
R921
47K
S/T_SCL
R935
100
S/T_SCL
14
B
Q905 E
2SC3052
COMMERCIAL
COMMERCIAL
D903
CDS3C05HDMI1
5.6V
ST_SDA
15
16
COMMERCIAL_US
R910
0
S/T_SDA
R936
100
.
D904
CDS3C05HDMI1
5.6V
WIRELESS
R907
22
+3.5V_ST
IR_PASS
WIRELESS
Q904
2SC3052
WIRELESS
Zener Diode is
close to wafer
+3.5V_ST
R912
47K
WIRELESS
R914
10K
R918
47K
WIRELESS
B
E
WIRELESS
R922
47K
C
B
Q906
2SC3052
WIRELESS
THE

WIRELESS
BCM35230
IR/KEY
50
WIRELESS READY MODEL

DUAL COMPONENT
D1001,D1002
1ST : EAH42720601
Q1001
1ST : EBK61012601, 2ND : 0TRDI80002A
Q1002
1ST : EBK60752501, 2ND : EBK61011501
2ND : EAH60994401
JK1001
KJA-PH-3-0168
Wireless power
WIRELESS
VCC(24V/20V/17V)_1
VCC(24V/20V/17V)_2
VCC(24V/20V/17V)_3
VCC(24V/20V/17V)_4
VCC(24V/20V/17V)_1
+24V
VCC(24V/20V/17V)_1
DETECT
+3.3V_Normal
R1002
22K
INTERRUPT
C1002
2.2uF
WIRELESS
WIRELESS
R1008
10K
WIRELESS
G
Q1002
R1003
2.2K
WIRELESS_PWR_EN
R1001
10K
B
L1001
AO3407A
WIRELESS
WIRELESS
R1007
WIRELESS
RESET
1K
GND_2
WIRELESS
I2C_SCL
WIRELESS_DET
MLB-201209-0120P-N2
GND_1
WIRELESS_SCL
I2C_SDA
WIRELESS_SDA
Q1001
MMBT3904(NXP)
WIRELESS
WIRELESS
GND_3
C1004
10uF
35V
UART_RX
WIRELESS
UART_TX
GND_4
IR
IR_PASS
GND_6
5.6V
5.6V
WIRELESS
D1002
CDS3C05HDMI1
WIRELESS
D1001
CDS3C05HDMI1
GND_5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
SHIELD
Wireless I2C connection with I2C_1

Address : 0X20
WIRELESS_SCL
WIRELESS_SDA
R1005
33
WIRELESS
R1006
33
SCL2_3.3V
SDA2_3.3V
WIRELESS
THE

BCM35230
WIRELESS
10
50
CVBS 1 PHONE JACK

CVBS2 REAR JACK
+3.3V_Normal
AV2
R1141
22
R1112
2.7K
AV2_R_IN
D1109
AMOTECH
5.6V
AV2
R1113
1K
AV1_CVBS_DET
C1118
560pF
50V
AV2
R1116
470K
AV2
AV2
R1142
22
D1105
5.6V
AV2_L_IN
JK1102
KJA-PH-1-0177
5
M5_GND
M4
D1110
AMOTECH
5.6V
AV2
JK1104
R1136
10
1
6
ZD1115
5.1V
M3_DETECT
ZD1116
5.1V
M1
R1109
75
1%
C1119
560pF
50V
AV2
R1117
470K
AV2
PPJ233-01
AV1_CVBS_IN
C1123
560pF
50V
AV2
AV2_JACK
C1106
47pF
50V
5C
[RD]E-LUG
4C
[RD]O-SPRING
3C
[RD]CONTACT
AV2
R1140
10
AV2
M6
JACK_PACK
JK1105
R1143
22
4B
[WH]C-LUG
3A
[YL]CONTACT
4A
[YL]O-SPRING
5A
[YL]E-LUG
AV2
PPJ238-01
C1124
560pF
50V
AV2
ZD1101
5.1V
AV2
AV2_CVBS_IN
C1120
47pF
50V
AV2
R1118
75
ZD1102
5.1V
AV1_L_IN
R1110
D1107
5.6V
C1109
560pF
50V
C1107
560pF
50V
470K
6C
[RD1]E-LUG
5C
[RD1]O-SPRING
4C
[RD1]CONTACT
5B
[WH1]O-SPRING
+3.3V_Normal
R1128
2.7K
AV2
AV2_CVBS_DET
R1144
22
4A
[YL1]CONTACT
5A
[YL1]O-SPRING
6A
[YL1]E-LUG
6H
[RD2]E-LUG
5H
[RD2]O-SPRING_2
AV2
5.6V
AV1_R_IN
R1111
470K
D1108
5.6V
C1108
560pF
50V
C1110
560pF
50V
R1129
1K
AV2
D1111
4H
[RD2]CONTACT
5G
[WH2]O-SPRING
5F
[RD2]O-SPRING_1
7F
[RD2]E-LUG-S
5E
[BL2]O-SPRING
7E
[BL2]E-LUG-S
4D
[GN2]CONTACT
5D
[GN2]O-SPRING
6D
[GN2]E-LUG
COMP2 REAR JACK
C1113
560pF
50V
COMP2
BLM18PG121SN1D
L1104
5.6V
COMP2
COMP2
R1123
D1113
COMPONENT 1 PHONE JACK
5.6V
COMP2
COMP2
C1114
560pF
50V
470K
COMP2
COMP2
COMP2
R1105
2.7K
ZD1103
5.1V
ZD1104
5.1V
R1120
0
COMP1_DET
COMP2
D1101
5.6V
JK1101
KJA-PH-1-0177
5
4
COMP2
ZD1106
5.1V
M5_GND
R1137
10
M4
M3_DETECT
M1
M6
ZD1110
5.1V
C1115
27pF
50V
COMP2_Pb
R1106
75
C1102
47pF
50V
1%
COMP2
COMP2
C1125
47pF
50V
ZD1107
5.1V
ZD1108
5.1V
L1107
CM2012FR27KT
R1135
10
COMP2_Y
ZD1112
5.1V
SC_G/COMP2_Y
COMP_EU
C1117
C1117-*1
27pF
47pF
50V
50V
COMP_EU
COMP_NON_EU
COMP2
R1126
75
COMP2
+3.3V_Normal
2.7K
C1130-*1
47pF
50V
FOR EMI
1K
R1130
SC_DET/COMP2_DET
COMP2
D1114
L1112
CM2012FR27KT
COMP1_Pr
ZD1114
5.1V
50V
COMP_EU
COMP2
R1127
C1126
27pF
50V
1%
R1139
10
ZD1113
5.1V
COMP_NON_EU
C1130
27pF
L1111
CM2012FR27KT
C1103
27pF
50V
R1107
75
COMP_NON_EU
COMP2_Y
COMP1_Pb
ZD1111
5.1V
C1129
27pF
50V
C1116
27pF
50V
L1107-*1
CM2012FR10KT
R1121
0
COMP2
R1138
10
SC_B/COMP2_Pb
COMP2_Pb
COMP2
L1110
CM2012FR10KT
C1128
27pF
50V
L1108
CM2012FR27KT
R1134
10
COMP1_Y
ZD1117
5.1V
SC_R/COMP2_Pr
COMP2_Pr
COMP2
COMP2
R1125
75
ZD1105
5.1V
SC/COMP2_L_IN
L1109
CM2012FR27KT
COMP2_Pr
COMP2
R1114
1K
COMP2
R1132
22
R1133
10
COMP2
R1124
75
C1121
560pF
50V
COMP2
COMP2
C1122
560pF
50V
COMP2
R1119
0
SC/COMP2_R_IN
COMP2
COMP2
R1122
470K
D1112
+3.3V_Normal
COMP2
R1131
22
BLM18PG121SN1D
L1103
R1108
75
C1104
27pF
50V
COMP2
5.6V
C1127
27pF
50V
1%
FOR EMI
THE

BCM35230
COMP/AV
11
50
USB_WIFI
DUAL COMPONENT
D1201,D1202
D1203,D1204
D1205,D1206
+5V_USB
L1202 WIFI 120-ohm
1ST : EAH42720601
2ND : EAH60994401
MLB-201209-0120P-N2
C1234
0.1uF
16V
WIFI
C1233
0.1uF
16V
WIFI
P1201
For EMI
12507WR-04L
WIFI
C1232
100uF
16V
WIFI
VDD
Close to BCM IC
R1232
WIFI_DM
DM
WIFI
R1233
WIFI_DP
DP
WIFI
GND
D1202
CDS3C05HDMI1
5.6V
WIFI_ESD
D1201
CDS3C05HDMI1
5.6V
WIFI_ESD
4
5
USB / DVR Ready
+3.3V_Normal
IC1204
AP2191DSG
L1205
MLB-201209-0120P-N2
USBDP_DN[1]
1
C1218
0.1uF
OPT
23
VDD33_2
R1215
100K OPT
22
SDA/SMBDATA/NON_REM[1]
R1214
100K OPT
IC1202
USB2512B-AEZG
WIFI
D1207
RCLAMP0502BA
OPT
USB_DP1
NC_6
R1216
WIFI
C1216
100K OPT
C1219
10uF
10V
1 GND
OUT_2 7
2 IN_1
OUT_1 6
3 IN_2
FLG 5
WIFI
C1217
4.7uF
R1220
4.7K
OPT
4 EN
EAN61849601
USB_CTL2
C1223
0.1uF
R1222
2.7K
NON_WIFI
R1228
0
R1229
0
R1209
100K WIFI
C1230
100uF
16V
NC 8
/USB_OCD2
SIDE_USB_CTL2
SIDE_USB_OCD2
NON_WIFI
0.1uF
+3.3V_USB
+5V_USB
AP2191DSG
3AU04S-305-ZC-(LG)
JK1202
R1208
100K WIFI
NC_5
OCS_N[2]
VDD33_1
PRTPWR[2]/BC_EN[2]
SIDE_USB_DP
USB_DM2
USB_DP2
D1204
CDS3C05HDMI1
5.6V
D1206
CDS3C05HDMI1
5.6V
NON_WIFI
R1226
0
R1227
0
NON_WIFI
WIFI_DM
WIFI_DP
/USB_OCD2
1uF
10V
WIFI
USB_CTL2
CRFILT
WIFI
C1214
0.1uF
SIDE_USB_DM
NON_WIFI
IC1203
USB DOWN STREAM
C1212
R1225
+3.3V_Normal
D1208
RCLAMP0502BA
OPT
19
/USB_OCD1
NON_WIFI
R1224
0
USB_CTL1
D1205
CDS3C05HDMI1
5.6V
D1203
CDS3C05HDMI1
5.6V
L1204
MLB-201209-0120P-N2
NC_4
VDDA33_2
SIDE_USB_OCD1
USB_DM1
+3.3V_USB
NC_7
18
20
17
16
NC_3
15
NC_8
14
21
13
R1207
100K WIFI
NC_2
SIDE_USB_CTL1
NON_WIFI
120-ohm
THE
/USB_OCD1
R1231
4
R1213
100K
OPT
SCL/SMBCLK/CFG_SEL[0]
USB_CTL1
USB
HS_IND/CFG_SEL[1]
C1224
0.1uF
R1223
2.7K
/RST_HUB
24
NC_1
4 EN
EAN61849601
NON_WIFI
R1230
0
5
RESET_N
25
C1208
0.1uF
WIFI
10uF
10V
100K
WIFI
R1206
SUSP_IND/LOCAL_PWR/NON_REM[0]
VDDA33_3
29
USBDP_UP
PLLFILT
USBDM_UP
30
31
28
C1211 WIFI
15pF
C1213 WIFI
15pF
32
33
34
VDD33_3
RBIAS
35
26
0.1uF R1212
100K
WIFI
OPT
12
C1207
0.1uF
WIFI
VBUS_DET
OCS_N[1]
C1206
0.1uF
WIFI
3 IN_2
FLG 5
C1215
27
USBDM_DN[2]
VDDA33_1
2 IN_1
OUT_1 6
+3.3V_USB
USBDP_DN[2]
PRTPWR[1]/BC_EN[1]
C1205
0.1uF
WIFI
10
C1204
1uF
10V
WIFI
THERMAL
37
11
USB_DM2
USB_DP2
TEST
USB_DP1
36
[EP]VSS
USB_DM1
+3.3V_USB
XTALOUT
XTALIN/CLKIN
WIFI
X1201
24MHz
WIFI
USBDM_DN[1]
SIDE_USB_DM
WIFI
C1209
1uF
10V
C1210
0.1uF
WIFI
+3.3V_USB
OUT_2 7
+5V_USB
R1221
4.7K
OPT
1 GND
3AU04S-305-ZC-(LG)
JK1201
WIFI
R1205
1M 1%
1/16W 1%
WIFI
R1204
12K
+3.3V_Normal
L1203
BLM18PG121SN1D
C1231
100uF
16V
USB DOWN STREAM
SIDE_USB_DP
120-ohm
C1220
NC 8
BCM35230
USB + WIFI
12
TI solution M_REMOTE OPTION

+3.3V_Normal
+3.3V_Normal
P1302
12507WR-12L
L1303
M_REMOTE
1
10
11
12
120-ohm
M_REMOTE
3.3V
GND
RX
R1321
M_REMOTE
R1315
100
M_REMOTE_RX
TX
M_REMOTE
R1316
100
RESET
M_REMOTE
R1317
100
DC
M_REMOTE
R1318
100
2.7K
M_REMOTE
R1322
2.7K
M_REMOTE
R1323
2.7K
M_REMOTE
M_REMOTE_TX
M_RFModule_RESET
DC_MREMOTE
DD
M_REMOTE
R1319
100
DD_MREMOTE
GND
GPIO_0
M_REMOTE
R1320
22
GPIO_1
M_REMOTE
R1324
22
GPIO_2
M_REMOTE
R1325
22
3D_SYNC
M_REMOTE
R1326
22
3D_GPIO_0
3D_GPIO_1
3D_GPIO_2
3D_SYNC_RF
13
.
ALL M_REMOTE OPTION
THE

BCM35230
M_REMOCON
13
50
Ethernet Block
DUAL COMPONENT
D1401,D1402
D1403,D1404
D1405,D1406
1ST : EAH42720601
2ND : EAH60994401
+2.5V_BCM35230
L1401
MLB-201209-0120P-N2
JK1401
XRJH-01A-4-DA7-180-LG(B)
10
11
D1
D2
D3
D4
C1401
0.1uF
16V
R1
R2
EPHY_TDP
R3
EPHY_TDN
R4
EPHY_RDP
R5
EPHY_RDN
R6
R7
D1401
D1402
5.5V
LAN_ESD
5.5V
LAN_ESD
D1404
5.5V
LAN_ESD
D1406
5.5V
LAN_ESD
R8
R9
R10[GND]
+3.3V_Normal
R11
YL_C
EPHY_ACTIVITY
YL_A
R1401
240
R1402
240
GN_C
EPHY_LINK
GN_A
12
D1403
D1405
5V
LAN_ESD
5V
LAN_ESD
SHIELD
THE

BCM35230
ETHERNET
14
50
FHD120Hz LVDS output(51pin+41Pin)

P1501
P1502
FI-RE51S-HFK-A
FI-RE41S-HFK-A
LVDS_41P
R1504
33
FRC2
3D_SYNC_RF
LVDS_SEL
LVDS_41P
C1504
2.2uF
50V
2
3
3
4
R1506
33
FRC2
R1507
33
FRC2
R1508
33
FRC2
SDA2_3.3V
+3.3V_Normal
4
5
SCL2_3.3V
R1513
FRC_RESET
7
8
3.3K
LVDS_SEL_HIGH
7
8
R1514
10K
LVDS_SEL_LOW
9
10
REVERSE MARK
R1516
33
SHARP_OPT
PANEL_CTL
11
10
TXC0N
11
TXC0P
12
TXA0N
12
TXC1N
13
TXA0P
13
TXC1P
14
TXA1N
14
TXC2N
15
TXA1P
15
TXC2P
16
TXA2N
16
17
TXA2P
17
TXCCLKN
18
TXCCLKP
18
19
TXACLKN
19
20
TXACLKP
20
TXC3N
21
TXC3P
TXA3N
22
TXC4N
23
TXA3P
23
TXC4P
24
TXA4N
24
25
TXA4P
25
21
22
26
BIT_SEL
27
26
TXD0N
27
TXD0P
28
TXD1N
29
TXD1P
TXB1N
30
TXD2N
TXB1P
31
TXD2P
32
TXB2N
32
33
TXB2P
33
TXDCLKN
34
TXDCLKP
28
TXB0N
29
TXB0P
30
31
R1512
10K
BIT_SEL_LOW
34
35
TXBCLKN
35
36
TXBCLKP
36
TXD3N
37
TXD3P
37
38
TXB3N
38
TXD4N
39
TXB3P
39
TXD4P
40
TXB4N
40
41
TXB4P
41
42
42
43
44
45
46
PANEL_VCC
47
48
L1501
49
MLB-201209-0120P-N2
NON_SHARP_60INCH
50
51
52
C1501
10uF
25V
OPT
C1502
1000pF
50V
C1503
0.1uF
16V
THE
BCM35230
LVDS
2010.11.03
15
50
[Local Dimming Block]
P1601
12507WR-08L
L/Dim Wafer
1
L/DIM0_SCLK
L/DIM0_MOSI
R1601
33
SCL2_3.3V
LPB_42/47/55
7
R1602
33
SDA2_3.3V
LPB_42/47/55
8
L/DIM0_VS
THE
BCM35230
L_DIMMING
16
50
+3.3V_Normal
DUAL COMPONENT
C1834
1000pF
50V
2ND : 0TR387500AA
50V
1ST : 0TRIY80001A
C1837
L1803
BLM18PG121SN1D
AUD_MASTER_CLK
+24V_AMP
22000pF
Q1801
AMP_RESET_N
OPT
R1851
3.3
DVDD_PLL
LF
10K
PVDD1_1
PVDD1_2
PVDD1_3
OUT1A_1
OUT1A_2
BST1A
/RESET
AD
PGND1A
37
38
39
40
41
42
43
33
BST1B
32
VDR1
DVDD
29
VDR2
P1801-*1
TJC2508-4A
SPK_R+
C1868
1uF
25V
C1854
22000pF
50V
SPK_WAFER_STRIGHT
SPK_WAFER_ANGLE
24
OUT2A_1
23
OUT2A_2
25
22
26
12
21
11
20
C1858
1uF
25V
SPK_R-
SDA
19
4.7K
P1801
C1856
1uF
25V
BCK
18
R1832
12
R1840
SPK_L-
PGND2A
17
SPEAKER_L
C1878
0.1uF
50V
NRS6045T100MMGK
SPK_L+
27
16
R1824
12
4.7K
C1871
0.47uF
50V
SMAW250-H04R
10
15
C1877
0.1uF
50V
R1839
C1853
22000pF
50V
WCK
C1815
33pF
50V
L1810
10.0uH
NRS6045T100MMGK
C1864
390pF
50V
D1806
1N4148W
100V
OPT
BST2A
28
PVDD2_3
PVDD2_2
PVDD2_1
OUT2B_2
BST2B
PGND2B
SPK_R+
100 C1807
1000pF
50V
+24V_AMP
D1807
1N4148W
100V
OPT
R1825
12
R1833
12
C1844
C1840
0.1uF
50V
C1838
35V
D1808
1N4148W
100V
OPT
22000pF
C1866
390pF
50V
R1826
12
C1872
0.47uF
50V
L1807
10.0uH
C1850
10uF
L1806
10.0uH
NRS6045T100MMGK
C1865
390pF
50V
0.1uF
50V
NRS6045T100MMGK
R1830
12
C1879
R1841
0.1uF
50V
4.7K
C1880
R1842
0.1uF
50V
4.7K
SPEAKER_R
50V
AMP_MUTE_HOTEL
R1803
0
R1834
12
SPK_L-
GND_2
OUT2B_1
Q1801
2SC3052
PGND1B
VCC_5
MONITOR2
34
30
MONITOR1
R1801
OUT1B_1
31
R1816
AMP_MUTE
35
R1802
10K
OUT1B_2
DGND
SCL
NTP
C1811
33pF
50V
IC1802
NTP-7400L
13
100
NTP
R1808
+3.5V_ST
THERMAL
49
36
AUD_SCK
SCL3_3.3V
R1823
12
L1811
10.0uH
AUD_LRCK
100
SPK_L+
GND_1
C1826
0.1uF
16V
SDATA
R1807
OPT
C1881
0.01uF
50V
D1805
1N4148W
100V
OPT
DGND_PLL
AUD_LRCH
SDA3_3.3V
44
45
AVDD_PLL
3.3K
46
47
AGND_PLL
14
R1815
OPT
C1820
10uF
10V
C1848
10uF
35V
C1863
390pF
50V
MONITOR0
100pF
50V
C1846
0.1uF
50V
C1842
0.1uF
50V
C1825
0.1uF
16V
/FAULT
C1804
C1806
1000pF
50V
OPT
C1819
10uF
10V
C1814
0.1uF
16V
48
OPT
C1810
10uF
10V
C1802
0.1uF
50V
C1801
0.1uF
50V
GND_IO
16V
CLK_I
0.1uF
L1801
MLB-201209-0120P-N2
C1883
10uF
10V
[EP]
C1832
VDD_IO
+24V_AMP
+24V
SPK_RSUB_MUTE
OPT
+3.3V_Normal
WOOFER
C1833
1000pF
50V
WOOFER
WOOFER
R1818
50V
3.3K
GND_IO
AD
/RESET
BST1A
PGND1A
OUT1A_2
OUT1A_1
PVDD1_3
PVDD1_2
PVDD1_1
46
45
44
43
42
41
40
39
38
37
VCC_5
30
GND_2
29
VDR2
28
BST2A
10
27
PGND2A
SUB_MUTE
THE
WOOFER
IC1801
NTP-7400L
25
OUT2A_1
13
D1802
1N4148W
100V
OPT
WOOFER
R1819
12
WOOFER
C1859
390pF
50V
WOOFER
C1860
390pF
50V
WOOFER
R1820
12
WOOFER
R1831
12
L1808
10.0uH
WOOFER
NRS6045T100MMGK
L1809
10.0uH
WOOFER
R1828
12
WOOFER
C1869
0.47uF
50V
WOOFER
C1873
0.1uF
50V
WOOFER
C1874
0.1uF
50V
WOOFER
NRS6045T100MMGK
WOOFER
R1835
4.7K
WOOFER_L
WOOFER
R1836
4.7K
SPK_WOOFER_L-
WOOFER
C1851
22000pF
50V
P1802
SMAW250-05
WOOFER
WOOFER
C1855
1uF
25V
WOOFER
C1857
1uF
25V
SPK_WOOFER_R-
SPK_WOOFER_R+
WOOFER
C1867
1uF
25V
WOOFER
C1852
22000pF
50V
SPK_WOOFER_L-
SPK_WOOFER_L+
24
12
23
SDA
22
OUT2A_2
21
26
20
11
17
BCK
100 WOOFER
C1829
1000pF
50V
WOOFER
C1836
22000pF
50V
PVDD2_3
PVDD2_2
PVDD2_1
OUT2B_2
OUT2B_1
PGND2B
BST2B
MONITOR2
MONITOR1
SPK_WOOFER_R+
SCL
NTP_WOOFER
NTP_WOOFER
C1813
33pF
50V
WOOFER
R1817

VDR1
31
AUD_SCK
C1809
33pF
50V
32
DGND
WCK
SCL3_3.3V
BST1B
AUD_LRCH
WOOFER
R1812
100
33
THERMAL
49
4
5
AUD_LRCK
WOOFER
R1811
100
PGND1B
GND_1
SDATA
SDA3_3.3V
OUT1B_1
DGND_PLL
DVDD
SPK_WOOFER_L+
34
OPT
C1882
0.01uF
50V
D1801
1N4148W
100V
OPT
35
DVDD_PLL
16
C1823
0.1uF
16V
WOOFER
C1847
10uF
35V
OUT1B_2
15
WOOFER
WOOFER
C1845
0.1uF
50V
WOOFER
C1841
0.1uF
50V
36
AVDD_PLL
LF
OPT
C1817
10uF
10V
CLK_I
AGND_PLL
R1814
47
WOOFER
C1822
0.1uF
16V
MONITOR0
100pF
50V
OPT
C1816
10uF
10V
/FAULT
WOOFER
C1803
WOOFER
C1812
0.1uF
16V
OPT
C1808
10uF
10V
WOOFER
C1805
1000pF
50V
WOOFER
14
16V
C1884
10uF
10V
OPT
R1852
3.3
VDD_IO
0.1uF
WOOFER
[EP]
WOOFER
C1831
+24V_AMP
48
AUD_MASTER_CLK
22000pF
10K
19
BLM18PG121SN1D
AMP_RESET_N
C1835
WOOFER
L1802
18
WOOFER AMP.
+24V_AMP
WOOFER
C1839
WOOFER
C1843
0.1uF
50V
0.1uF
50V
D1803
1N4148W
100V
OPT
WOOFER
C1849
10uF
35V
D1804
1N4148W
100V
OPT
WOOFER
R1821
12
WOOFER
R1829
12
WOOFER
C1861
390pF
50V
WOOFER
C1862
390pF
50V
WOOFER
R1822
12
L1804
10.0uH
WOOFER
WOOFER
C1870
0.47uF
50V
NRS6045T100MMGK
L1805
10.0uH
NRS6045T100MMGK
WOOFER
R1827
12
WOOFER
C1875
WOOFER
R1837
0.1uF
50V
4.7K
WOOFER
C1876
WOOFER
R1838
0.1uF
50V
4.7K
WOOFER_R
WOOFER
SPK_WOOFER_R-
BCM35230
AUDIO[NEO]
18
50
DUAL COMPONENT
PCM_MDI[0-7]
BCM INT Demod
R1909
22 OPT
PCM_MDI[1]
R1910
22 OPT
PCM_MDI[2]
AR1903
22 OPT
1ST : 0TRIY80001A
Q1902
1ST : EBK60752501, 2ND : EBK61011501
IC1904
1ST : 0ISTLPH062A, 2ND : EAN40055001
2ND : 0TR387500AA
CI_MDI[0-7]
Close to BCM35230
PCM_MDI[0]
Q1901
CI_MDI[0]
CI_MDI[1]
CI_MDI[2]
PCM_MDI[3]
CI_MDI[3]
PCM_MDI[4]
CI_MDI[4]
+5V_CI_ON
CI_MDI[5]
PCM_MDI[5]
PCM_MDI[6]
R1915
22 OPT
CI_MDI[6]
PCM_MDI[7]
R1916
22 OPT
CI_MDI[7]
C1904
0.1uF
CI
FE_TS_DATA[0-7]
FE_TS_DATA[0]
R1901
FE_TS_DATA[1]
R1902
FE_TS_DATA[2]
22
22
C1905
10uF
10V
CI
R1932
10K
CI
R1933
10K
OPT
CI_DATA[0-7]
P1901
10067972-000LF CI
+5V_CI_ON
R1937
/CI_CD1
CI
FE_TS_DATA[4]
CI_TS_DATA[3]
R1903
22
CI
R1904
22
CI
R1905
22
CI
FE_TS_DATA[5]
R1906
22
CI
FE_TS_DATA[6]
FE_TS_DATA[7]
R1907
22
CI
R1908
22
CI
R1971
10K
CI
R1976
/PCM_IORD
/PCM_IOWR
R1972
10K
CI
GND
DAT3
CI_DATA[3]
37
DAT4
CI_DATA[4]
TS_OUT4
38
CI_TS_DATA[5]
CI_TS_DATA[6]
CI_TS_DATA[7]
22 CI
22 CI
R1974
CI_MDI[0-7]
Close to BCM35230
BCM INT Demod
R1917
22 OPT
R1918
22 OPT
PCM_MISTRT
PCM_MIVAL_ERR
R1919
PCM_MCLKI
CI_MISTRT
CI_MIVAL_ERR
22 OPT
CI_MCLKI
NIM_VAL_ERR
R1920
22
CI
R1921
22
CI
R1922
22
CI
NIM_TS_CLK
R1927
PCM_RST
CARD_EN2
42
ADDR10
CI
R1962
VS1
43
/O_EN
R1963
22
IORD
44
10
ADDR11
CI
CI
R1957
IOWR
45
11
ADDR10
CI
R1958
22
22
CI_ADDR[8]
/PCM_OE
PCM_ADDR[11]
CI
R1959
CI
R1960
22
PCM_ADDR[13]
ADDR14
CI
R1961
22
CI_ADDR[14]
CI_MDI[2]
TS_IN2
49
15
/WR_EN
CI_MDI[3]
TS_IN3
50
16
/IRQA
0
OPT
51
17
VPP
52
18
VPP
R1967
53
19
TS_IN_VAL
54
20
TS_IN_CLK
CI_MDI[6]
TS_IN6
55
21
ADDR12
TS_IN7
56
22
ADDR7
TS_OUT_CLK
57
23
ADDR6
CI_TS_DATA[2]
/CI_CD2
R1944
TS_IN4
TS_IN5
CI_MDI[7]
CI_TS_DATA[0]
0.1uF
CI
C1910
R1968
10K
CI
PCM_ADDR[13]
R1975
10K
CI
R1964
CI
22
22 CI
/PCM_WE
/PCM_IRQA
OPT
CI R1947
22
PCM_ADDR[12]
CI R1948
CI R1949
22
PCM_ADDR[7]
22
CI R1950
CI R1951
22
CI_ADDR[6]
CI_ADDR[5]
22
PCM_ADDR[4]
CI R1952
CI R1953
22
PCM_ADDR[3]
22
PCM_ADDR[2]
CI R1954
CI R1955
22
CI_ADDR[1]
22
CI_ADDR[0]
CI_RESET
58
24
ADDR5
CI_WAIT
59
25
ADDR4
60
26
ADDR3
61
27
ADDR2
62
28
ADDR1
TS_OUT_SYN
63
29
ADDR0
TS_OUT0
64
30
DAT0
CI_DATA[0]
TS_OUT1
65
31
DAT1
CI_DATA[1]
TS_OUT2
R1938 CI 62 /CI_DET2
GND
66
32
DAT2
67
33
/IO_BIT
68
34
GND
69
CI_ADDR[8]
CI_ADDR[14]
C1913
0.1uF
16V
CI
R1934 10K OPT INPACK

REG
R1935 0 CI
TS_OUT_VAL
G2
+5V_CI_ON
PCM_ADDR[9]
ADDR8
VCC
PCM_ADDR[11]
PCM_ADDR[9]
ADDR13
VCC
R1973
10K
CI
CI_ADDR[10]
14
CI_TS_DATA[1]
PCM_TS_DATA[2]
CI_ADDR[10]
12
R1936
CI_TS_DATA[0-7]
+5V_CI_ON
22
22
13
CI_TS_SYNC
100 CI
CI_DATA[7]
CI R1956
48
CI_TS_DATA[1]
AR1901
/CARD_EN1
46
CI_TS_DATA[0]
Close to CI Slot
47
CI_TS_VAL
PCM_TS_DATA[0]
PCM_TS_DATA[1]
41
TS_IN1
CI TS INPUT
PCM_TS_DATA[0-7]
CI_DATA[6]
TS_OUT7
TS_IN0
22 CI
22 CI
R1928
DAT6
DAT6
CI_MDI[1]
CI_TS_CLK
/PCM_WAIT
5
6
CI_MDI[0]
CI_MDI[5]
R1930
10K
OPT
CI_DATA[5]
39
40
22
CI_MDI[4]
R1929
10K
OPT
DAT5
TS_OUT5
TS_OUT6
TS_IN_SYN
+5V_CI_ON
R1977
10K
OPT
Close to Tuner
NIM_TS_SYNC
/PCM_CE1
35
36
CI_TS_DATA[4]
FE_TS_DATA[3]
R1946
10K
OPT
GND
62 /CI_DET1
CI TS_OUT3
CI
PCM_ADDR[12]
PCM_ADDR[7]
CI_ADDR[6]
CI_ADDR[5]
PCM_ADDR[4]
PCM_ADDR[3]
PCM_ADDR[2]
CI_ADDR[1]
CI_ADDR[0]
+5V_CI_ON
CI_DATA[2]
R1945
10K
OPT
G1
CI_TS_DATA[2]
PCM_TS_DATA[3]
CI_TS_DATA[3]
PCM_TS_DATA[4]
AR1902
100 CI
CI_TS_DATA[4]
PCM_TS_DATA[5]
CI_TS_DATA[5]
CI_MIVAL_ERR
PCM_TS_DATA[6]
CI_TS_DATA[6]
CI_MCLKI
CI_TS_DATA[7]
CI_MISTRT
PCM_TS_DATA[7]
Close to CI Slot
100 CI
R1925
100 CI
CI_TS_CLK
CI_TS_VAL
OE
L
L
H
CI_TS_SYNC
C1916
12pF
50V
OPT
CI TS OUTPUT
DIR
L
H
X
CI_DATA
OUTPUT
INPUT
Z
NAND_DATA
INPUT
OUTPUT
Z
/CI_EN1
R1926
CI POWER ENABLE CONTROL

+3.3V_CI
IC1903
74LVC245A
22 CI
20
CI
CI_DATA[0-7]
OE
B0
B1
CI_DATA[2]
B2
B3
CI_DATA[3]
R1980
CI_DATA[4]
AR1905
B4
100 CI
B5
CI
CI_DATA[7]
R1970
22
18
22 CI
NAND_REb
NAND_DATA[0-7]
OPT
CI
C1906
0.1uF
16V
17
16
15
14
13
12
11
10
R1943
22K
CI
A0
NAND_DATA[0]
A1
NAND_DATA[1]
A2
NAND_DATA[2]
A3
NAND_DATA[3]
A4
NAND_DATA[4]
R1940
10K
OPT
A5
NAND_DATA[5]
A6
NAND_DATA[6]
A7
NAND_DATA[7]
R1942
4.7K
B7
C1912
0.1uF
16V
PCM_5V_CTL
C1909
4.7uF
16V
OPT
CI
C1914
0.1uF
16V
CI
R1969
10K
CI
R1987
2.2K
CI
C
Q1901
2SC3052
CI
CI
B6
CI_DATA[6]
+3.3V_CI
19
R1931
DIR
100 CI
CI_DATA[5]
+5V_CI_ON
AR1904 100 CI
CI_DATA[0]
CI_DATA[1]
L1902
BLM18PG121SN1D
Q1902
AO3407A
CI
VCC
+3.3V_CI
+5V_CI_ON
+5V_Normal
0.1uF
C1903
16V
OPT
220 CI
R1924
PCM_TS_SYNC
R1923
PCM_TS_CLK
PCM_TS_VAL
GND
NAND F/M Data
IC1901
CI 74LVC125APW
1OE
/CI_CE1
1A
NAND_REb
/PCM_OE
CI 9
1Y
2OE
2A
NAND_WEb
14
13
12
11
10
VCC
C1901
0.1uFOPT
16V
/CI_CE2
1A
/CI_CE1
4A
NAND_WEb
4Y
CI 45
/PCM_IOWR
1B
/CI_CE2
1Y
/CI_EN1
3OE
2A
/CI_EN1
CI 15
2Y
3A
2B
/PCM_WE
NAND_REb
GND
3Y
3,3V_CI POWER
IC1902
74AHC08PW
4OE
CI
14
13
12
11
10
VCC
+3.3V_CI
OPT
C1902
0.1uF
16V
OPT
4B
NAND_RBb
C1915
0.1uF
16V
IC1905
74LVC245A
4A
VCC
/CI_EN1
4Y
CI_ADDR[1]
R1986
22
CI
OE
B0
PCM_ADDR[2]
B1
3B
NAND_CLE
PCM_ADDR[3]
B2
PCM_ADDR[4]
CI 44
/PCM_IORD
/PCM_CE1
CI 7
2Y
3A
B3
PCM_ADDR[7]
B4
GND
PCM_ADDR[9]
3Y
CI_ADDR[0]
B5
PCM_ADDR[11]
B6
PCM_ADDR[12]
B7
PCM_ADDR[13]
CI
20
19
18
17
16
15
14
13
12
11
10
+3.3V_Normal
R1985
10K
CI
+3.3V_CI
DIR
L1901
BLM18PG121SN1D
A0
CI_ADDR[2]
A1
CI_ADDR[3]
CI
A2
CI_ADDR[4]
CI
A3
CI_ADDR[7]
CI C1908
0.1uF
C1907
0.1uF
A4
CI_ADDR[9]
A5
CI_ADDR[11]
A6
CI_ADDR[12]
A7
CI_ADDR[13]
GND
CI DETECT
+3.3V_CI
+3.3V_CI
R1939 R1941
10K
10K
CI
CI
CI CONTROL INTERFACE
GND
VCC
CI
/CI_CD2
/CI_CD1
+3.3V_CI
IC1904
74LVC1G32GW
OPT
C1911
0.1uF
16V
GND
CI
R1966
10K
CI
R1965
CI_DET
47
THE

BCM35230
CI
2010.11.11
19
58
DUAL COMPONENT
H/NIM & F/NIM & T/C/S2 Combo Tuner
OPTION TABLE
IC2204
H/NIM
H/NIM
(EU)
(AU,Latin)
Non_DVB_S
H/NIM
(Brazil,Taiwan)
Non_DVB_S
Non_DVB_S
BOOSTER
BOOSTER
Non_DVB_S
H/NIM
H/NIM
H/NIM
F/NIM_T2
F/NIM_T/C
Non_DVB_S
Non_DVB_S
F/NIM
BOOSTER
BOOSTER
F/NIM_Brazil
(Brazil)
DVB-T/C/S2
(Eu,Aisa)
Non_DVB_S
DVB_S
F/NIM
F/NIM
DVB_S: use DVB-T/C/S2 combo Tuner
BOOSTER
F/NIM: use F/NIM and DVB-T/C/S2 combo Tuner
BOOSTER
SCART
+5V_TU
SCART: use Scart Jack

RF_SW_CTL
RF_SW_CTL
SCART
SCART
SCART
EU_F/NIM
RF_SW_CTL
CN : use China F/NIM
CN
TC_S_F/NIM
ERROR & VALID PIN
BOOSTER: use BOOSTER_CTL
BOOSTER
L2201
RF_SW_CTL: use RF_SWITCH_CTL
EU_F/NIM
TC_S_F/NIM
1ST:T-AP2114H(EAN61573601) / 2ND:T-TJ3940S (EAN61573501)
NON_DVB_S: use H/NIM and F/NIM
H/NIM: use H/NIM
F/NIM
F/NIM
BOOSTER
F/NIM_CN
(China)
CN_F/NIM_BR
CN_F/NIM_BR
<EU, China, Brazil,S2>
R2263
0
BLM18PG121SN1D
TC_S_F/NIM: use EU_DVB-T/C F/NIM
TC_S_F/NIM
DVB_T2/CN_F/NIM_BR
CN_F/NIM_BR: use F/NIM(China, BRZIL)

EU_F/NIM: use EU_F/NIM
BOOSTER
R2231
0
RF_SWITCH_CTL
3
4
5
6
7
8
9
10
11
12
13
NC_1
+B1[5V]
RF_AGC
MOPLL_AS
SCL
SDA
NC_2
SIF
NC_3
10
VIDEO
11
GND
12
+B2[1.2V]
13
NC_1
BST_CNTL
+B1[5V]
NC_2[RF_AGC]
NC_3
SCLT
SDAT
NC_4
SIF
NC_5
10
VIDEO
11
GND
12
+B2[1.2V]
13
L2205
1uH
close to
NON_DVB_S
C2222
C2225
100pF
0.1uF
16V
50V
+3.3V_S2_TU
NON_DVB_S NON_DVB_S
NC_1
14
14
+B3[3.3V]
14
TUNER
NC_3
R2206
S2_TU[3.3V]
DVB_S
R2277
NC_4
C2201
0.1uF
16V
OPT
C2284
100pF
50V
DVB_S
C2285
0.1uF
16V
DVB_S
16
17
18
RESET
15
IF_AGC_CNTL
16
DIF_1[N]
17
DIF_2[P]
18
19
19
20
SHIELD
21
22
TAIWAN_BR_V
LATIN_TUNER_H
AU_ASIA_H/NIM_H
TU2201-*1
TDTR-T056F
TU2201-*2
TDVJ-H031F
TU2201-*3
TDTJ-S101D
23
RESET
15
+B4[2.5V]
16
SCL
17
SDA
18
ERR
19
SYNC
20
VALID
21
MCL
22
D0
23
GND
RF_BOOSTER_CTL
C2204
100pF
50V
DVB_S
T_1.8V
TU_SIF
R2268
0
TU_TS_CLK
0.1uF
16V
SCL0_3.3V
R2230
4.7K
DVB_S
Q2201
C MMBT3906(NXP)
DVB_S
R2243
0
NON_DVB_S
R2250
1K
OPT
R2252
220
TU_CVBS
B
Q2204
R2251 MMBT3906(NXP)
C
+1.25V_TU (EU)
+5V_TU
+1.23V_TU (CN)
R2255
200
SCART
R2254
200
SCART
R2247
0
SCART
+3.3V_TU
Max 1.5A
close to TUNER
T_CVBS
+1.25V_TU
+3.3V_TU
IC2208
AP2132MP-2.5TRG1
CN
TD_1.2V
C2205
100pF
50V
10uF
+3.3V_TU
C2220
1000pF
50V CN
C2218
4700pF
50V CN
C2210
0.1uF
16V
CN
C2214
100uF
16V
T_3.3V
R2229
100
CN
C2217
10uF
C2227
100pF
50V
R2233
100K
B
TU_RESET
C2231
0.1uF
16V
C2238
0.1uF
16V
T_TU_RESET
+2.5V_TU
C2213
0.1uF EU_F/NIM
16V
close to Tuner
F/NIM
R2204
0
TD_SCL
TD_SDA
H/NIM
R2293
0
R2292H/NIM
0
C2291
0.1uF
OPT
C2289
IF_AGC
2
EN
OPTION:SCART
10uF
16V
+5V_Normal
R2
GND
7
ADJ
R2213
11K
1%
R2214
11K
1%
R1
VOUT
VIN
4
2A
R2214-*1
10K
5
NC
VCTRL
1/16W
1%
CN
EAN61387601
R2215
22
C2290
10uF
16V
SCL1_3.3V
F/NIM
R2205
0
T/C/S2_ERROR
R2212
20K
1%
PG
R2210
10K
POWER_ON/OFF2_1
Q2205
MMBT3906(NXP)
C
SCART
EU_F/NIM
0
R2240
H/NIM
0
R2241
NC_6
+1.25V_TU
[EP]
ATV_OUT
E
C2215
NIM_TS_CLK
R2253
220
OPT 0
R2248
0
1K
OPT
GND_1
NIM_TS_SYNC
T_SIF
NC_5
NIM_VAL_ERR
TU_TS_SYNC
DVB_S
R2249
R2291
75
OPT
R2266
0
R2267
0
+5V_TU
SDA0_3.3V
C2219 C2221
C2202 C2211
62pF
62pF
20pF
20pF
50V
50V
50V
NON_DVB_S50V
NON_DVB_S NON_DVB_S
NON_DVB_S
C2208
0.1uF
16V
DVB_S
TS_VAL_ERR
DVB_TC/TCS_F/NIM
Tuner to CI Slot
R2237
82
C2235
DVB_S
L2210
270nH NON_DVB_S
+1.8V_TU
R2269
0
OUT_Y
TS_VAL_ERR
R2234
470
DVB_S
L2210-*1
DVB_S
0
C2286
10uF
6.3V
DVB_S close to TUNER
L2206
270nH NON_DVB_S
TU_SDA
BOOSTER
DVB_TC/TCS_F/NIM
TU_SCL
C2271
0.1uF
16V
OPT
close to TUNER
L2206-*1
DVB_S
0
close to TUNER
VCC
BOOSTER
0
16V
15
R2246
10K
+5V_TU
NC_2
16V
+B3[3.3V]
Q2203
2SC3052
C2234
0.01uF
50V
BOOSTER
+5V_TU
IN_A
NON_CN
ANT_PWR
2.2K
BOOSTER
B
C
TU2203
TDFQ-G031D
DVB_TC/TCS_F/NIM
EU_F/NIM_DVB_TCS_V
TU2202
TDFR-G156D
close to TUNER
IN_B
+3.3V_TU
THERMAL
EU_F/NIM_DVB_TC_V
TU2201
TDTJ-S131D
TU_TS_VAL
TU_TS_ERR
R2211
OPT 10K
AU_ASIA_TUNER_V
R2258
0
MMBT3906(NXP)
R2235
C2203
0.1uF
16V
RF_SW_CTL
10K
BOOSTER
Q2202
R2209
0 RF_SW_CTL
IC2203
NL17SZ08DFT2G
BOOSTER
R2242
close to TUNER
R2216
22
OPT
C2292
1uF
SDA1_3.3V
close to IF line
C2237
18pF
50V
OPT
T/C/S2_SYNC
C2241
18pF
50V
OPT
Vout=0.6*(1+R1/R2)
T/C/S2_VALID
IF_N
T/C/S2_MCL
IF_P
T/C/S2_D0
AR2200 47
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
RF_S/W_CTL
ANT_PWR[OPT]
BST_CNTL
SIF
GND
RESET
DIF_2[P]
19
SHIELD
IF_AGC
29
DIF_1[N]
17
DIF_2
18
19
25
D3
26
D4
27
D5
28
D6
29
30
31
SHIELD
D7
30
31
32
SHIELD
EU_F/NIM_DVB_T2_V
TU2202-*1
TDFR-G256D
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
31
30
CN_HORIZONTAL_ALTOBEAM
CN_VERTICAL_ALTOBEAM
TU2202-*2
TDFR-C256D
NC_1
BST_CNTL
+B1[5V]
NC_2[RF_AGC]
NC_3
SCLT
SDAT
NC_4
SIF
NC_5
10
VIDEO
11
GND
12
+B2[1.2V]
13
+B3[3.3V]
14
RESET
15
+B4[2.5V]
16
SCL
17
SDA
18
ERR
19
SYNC
20
VALID
21
MCL
22
D0
23
D1
24
D2
25
D3
26
D4
27
D5
28
D6
29
D7
31
30
CN_VERTIAL_LG3911
TU2202-*3
TDFR-C236D
RF_S/W_CNTL
BST_CNTL
+B1[+5V]
NC[RF_AGC]
NC_1
SCLT
SDAT
NC_2
SIF
NC_3
10
VIDEO
11
GND
12
+B2[1.2V]
13
+B3[3.3V]
14
RESET
15
NC_4
16
SCL
17
SDA
18
ERR
19
SYNC
20
VALID
21
MCL
22
D0
23
D1
24
D2
25
D3
26
D4
27
D5
28
D6
29
D7
31
30
CN_HORIZONTAL_LG3911
TU2202-*4
TDFR-C056D
RF_S/W_CNTL
BST_CNTL
+B1[+5V]
NC[RF_AGC]
NC_1
SCLT
SDAT
NC_2
SIF
NC_3
10
VIDEO
11
GND
12
+B2[1.2V]
13
+B3[3.3V]
14
RESET
15
NC_4
16
SCL
17
SDA
18
ERR
19
SYNC
20
VALID
21
MCL
22
D0
23
D1
24
D2
25
D3
26
D4
27
D5
28
D6
29
D7
31
30
TU2202-*5
TDFR-C036D
RF_S/W_CNTL
BST_CNTL
+B1[+5V]
NC[RF_AGC]
NC_1
SCLT
SDAT
NC_2
SIF
NC_3
10
VIDEO
11
GND
12
+B2[1.2V]
13
+B3[3.3V]
14
RESET
15
NC_4
16
SCL
17
SDA
18
ERR
19
SYNC
20
VALID
21
MCL
22
D0
23
D1
24
D2
25
D3
26
D4
27
D5
28
D6
29
D7
31
30
33
DVB_TCS_H
TU2203-*1
TDFQ-G001D
RF_S/W_CNTL
BST_CNTL
2
3
+B1[+5V]
4
NC[RF_AGC]
NC_1
SCLT
7
8
SDAT
9
NC_2
10
SIF
11
NC_3
12
13
VIDEO
14
GND
15
+B2[1.2V]
16
17
+B3[3.3V]
18
RESET
19
NC_4
20
SCL
21
22
SDA
23
ERR
24
SYNC
25
VALID
26
MCL
27
28
D0
29
D1
30
D2
31
D3
32
33
D4
34
D5
35
D6
36
D7
37
38
NC_1
SHIELD
TU_TS_CLK
EU_F/NIM
T/C/S2_D3
AR2200-*1
0
CN
IC2204
AR2200-*2
33
DVB_S
AP2114H-2.5TRG1
VIN
T/C/S2_D4
AR2201
47
T/C/S2_D5
OPT
FE_TS_DATA[1]
FE_TS_DATA[0]
T/C/S2_D6
FE_TS_DATA[3]
SHIELD
SHIELD
+1.25V_TU
C2223
100pF
50V
DVB_S
DVB_S
S2_RESET
S2_3.3V
S2_F22 R2202
51
35
S2_SCL 5%DVB_S
DVB_S
S2_TU[3.3V]
TU_SCL
TU_SDA
36
T_1.8V
T_SIF
R2283
37
GND_1
FE_TS_DATA[6]
T_TU_RESET
38
NC_6
AR2201-*2
33
DVB_S
Max 217mA
+1.8V_TU
EU_F/NIM
+3.3V_TU
IC2202
AZ1117BH-1.8TRE1
R2226
47
EU_F/NIM
DVB_S
GND_2
AR2202-*2
33
DVB_S
S2_RESET
R2284
AR2202-*1
0
CN
+3.3V_TU
FE_TS_DATA[7]
R2226-*1
0
R2226-*2
33
CN
DVB_S
IN
DVB_S
OUT
R2298
1
DVB_S
ADJ/GND
Close to the tuner

C2224
100pF
50V
DVB_S
S2_LNB
TD_SCL
C2228
0.1uF
16V
DVB_S
+3.3V_S2_LNB
L2204
MLB-201209-0120P-N2
+3.3V_S2_DE
TD_1.2V
T_3.3
C2287
10uF
10V
DVB_S
C2232
10uF
10V
DVB_S
OPT
C2242
0.1uF
DVB_S
T/C/S2_SYNC
C2245
10uF
10V
DVB_S
+3.3V_S2_DE
DVB_S
+3.3V_S2_TU
39
T/C/S2_VALID
Close to Tuner #38 pin
T/C/S2_D0
C2243
10uF
10V
DVB_S
C2246
0.1uF
DVB_S
L2203
MLB-201209-0120P-N2
Surge protectioin
T/C/S2_MCL
C2248
0.1uF
DVB_S
L2202
MLB-201209-0120P-N2
C2288
0.1uF
16V
DVB_S
TD_SDA
T/C/S2_ERROR
C2279
0.1uF
16V
EU_F/NIM
C2276
10uF
10V
EU_F/NIM
FE_TS_DATA[5]
FE_TS_DATA[4]
DVB_S
S2_SDA
NC_5
T_CVBS
AR2202
47
C2226
C2230
0.1uF
10uF
16V
10V
DVB_S
DVB_S
+3.3V_S2_LNB
R2208
2.2K
DVB_S
C2207
0.1uF
DVB_S
R2203
100
LNB_TX
1/16W
NC_4
AR2201-*1
0
CN
R2270
1
EU_F/NIM
GND
C2268
0.1uF
16V
EU_F/NIM
L2209
BLM18PG121SN1D
120-ohm
34
NC_3
VOUT
FE_TS_DATA[2]
T/C/S2_D7
S2_1.25V
3
1
NC_2
T/C/S2_D1
T/C/S2_D2
T/C/S2_D3
SHIELD
T/C/S2_D4
T/C/S2_D5
T/C/S2_D6
T/C/S2_D7
S2_1.25V
S2_RESET
S2_3.3V
C2206
1000pF
50V
DVB_S
C2209
33pF
OPT
C2212
33pF
DVB_S
D2201
3.0SMCJ20A(suzhougrande)
DVB_S
R2207
2.2K
DVB_S
6432
C2247
0.1uF
16V
DVB_S
C2244
10uF
10V
DVB_S
DVB_S
LNB_OUT
S2_F22
S2_SCL
+5V_Normal
S2_SDA
GND_2
+5V_TU
+3.3V_Normal
+3.3V_TU
CHBO_TS_CLK
S2_LNB
39
SHIELD
T/C/S2_D2
DIF_2[P]
18
19
SHIELD
D2
+2.5V_TU
+3.3V_TU
FE_TS_DATA[0-7]
TU_TS_VAL
RESET
16
DIF_1
17
28
+B3[3.3V]
15
IF_AGC_CNTL
16
DIF_1[N]
+B2[1.2V]
14
RESET
15
IF_AGC_CNTL
TU_TS_ERR
TU_TS_SYNC
GND
13
3.3V
14
27
VIDEO
12
1.2V
13
+B3[3.3V]
26
NC_3
11
GND
12
+B2[1.26V]
T/C/S2_D1
SIF
10
VIDEO
11
NC_2
NC
10
VIDEO
SDA
SIF
NC_4
24
SCL
NC(IF_TP)
25
MOPLL_AS
SDA
NC_3
RF_AGC
SCL
SDA
D1
+B1[5V]
AS
SCL
24
NC_1
NC[RF_AGC]
NC_2
ANT_PWR
+B
NC_1[RF_AGC]
BST_CNTL
+B[5V]
SHIELD
SHIELD
CHBO_TS_SERIAL
L2208
MLB-201209-0120P-N2
CHBO_TS_SYNC
CHBO_TS_VAL_ERR
TU_RESET_SUB
L2207
MLB-201209-0120P-N2
C2258
22uF
16V
C2252
0.1uF
16V
C2260
22uF
16V
C2262
0.1uF
16V
RF_SWITCH_CTL_2
C2216
22uF
16V
CN
C2249
0.1uF
16V
C2255
22uF
16V
C2259
0.1uF
16V
C2261
0.1uF
16V
TW9910_RESET
THE

BCM35230
TUNER SINGLE
22
DVB-S2 LNB Part Allegro

(Option:LNB)
D2301
LNB SMAB34
2A
D2304
SMAB34
40V
3A
40V
LNB
C2307
0.01uF
50V
LNB
C2302
1uF
50V
LNB
C2324
68uF
35V
LNB
+12V_LNB
C2305
68uF
35V
LNB
LNB
L2301
33UH
SP-7850_33
close to Boost pin(#1)
DCDC_GND
C2312
0.1uF
50V
C2311
10uF
25V
LNB
2.4A
DCDC_GND and A_GND are connected

DCDC_GND and A_GND are connected in pin#27
PCB_GND and A_GND are connected
close to VIN pin(#25)
LNB
DCDC_GND
D2302
US1M(suzhou)
DCDC_GND
A_GND
LNB_OUT
NC_1
TDO
EXTM
NC_9
BFI
BFO
22
23
VIN
24
LX
25
BFC
IC2301
A8290SETTR-T
18
NC_6
LNB
17
NC_5
16
NC_4
R2313
0
R2314
0
NC_3
LNB
LNB
15
14
A_GND
+3.3V_Normal
IRQ
GND
13
7
8
TDI
NC_7
19
NC_2
LNB_TX
20
12
A_GND
SCL
LNB
TCAP
11
22000pF
ADD
C2306
NC_8
THERMAL
29
10
LNB
21
VCP
SDA
BOOST
C2304 0.1uF
26
LNB
A_GND
27
A_GND
28
A_GND
GNDLX
Ouput trace widths should be sized to conduct at least 2A
C2301
0.22uF
25V
Input trace widths should be sized to conduct at least 3A
VREG
LNB
D2303
SMAB34
40V
LNB
C2303
0.1uF
50V
[EP]
1000V
LNB
DCDC_GND
A_GND
4.7K
LNB
LNB
R2303 0
C2310
OPT
LNB
27pF
R2302 33
OPT
C2309
27pF
LNB
R2301 33
LNB
C2308
0.22uF
R2304
A_GND
Max 1.3A
+12V_LNB
+12V
L2302
BLM18PG121SN1D
LNB
THE
LNB_INT
SCL1_3.3V
SDA1_3.3V
A_GND
BCM35230
LNB
2010.11.02
23
57
DUAL COMPONENT
Full Scart(18 Pin Gender)
Q2502,Q2503
Q2504,Q2506
Q2507,Q2508
1ST : 0TRIY80001A
Q2501
1ST : EBK61012701, 2ND : EBK58172301
Q2505
1ST : 0TRIH80004A, 2ND : EBK61012501, 3RD : 0TR102009AM
D2513
1ST : T-BAT54_SUZHO, 2ND : 0DSON00138A
2ND : 0TR387500AA
+5V_Normal
+3.3V_Normal
IN CASE OF SMALL= 15V

+12V
R2514
10K
EU
CLOSE TO JUNCTION
EU
L2506
R2525
SC_DET/COMP2_DET
EU
1K
EU
EU
E
MMBT3906(NXP)
Q2501
D2511
5.6V
470
EU
R2545
10K
EU
C2526
0.1uF
50V
EU
C2525
0.1uF
50V
R2536
DTV_ATV_SELECT
B
C
EU
C2511
R2577
10
R2522
SHIELD
C2536
47pF
50V
EU
EU
0.1uF
EU
CLOSE TO SOC
18
D2502
5.5V
EU
COM_GND
17
SYNC_IN
JP2502
SYNC_OUT
JP2503
EU
EU
C2515
100uF
16V
16
R_OUT
JP2505
EU
R2535
180
EU
R2579
10K
SYNC_GND
14
JP2504
Rg
+3.3V_Normal
15
RGB_IO
Rf
R2513
EU
R2581
1K
13
12
R_GND
OPT
D2503
30V
EU
R2506
75
1%
D2504
5.5V
EU
R2507
75
1%
EU
11
EU
R2578
10K
C
B
JP2506
G_OUT
10
G_GND
0 EU
VCC
EU
R2533
390
Gain=1+Rf/Rg
75
JP2501
SELECT
EU
C2524
47uF
16V
0
EU
19
AV_DET
IC2502
NLASB3157DFT2G
EU
R2537
47K
EU
R2538
15K
EU
B1
ATV_OUT
GND
L2507
120-ohm
B0
DTV/MNT_V_OUT
+3.3V_Normal
C2532
180pF
50V
OPT
EU
R2580
10K
EU
R2504
75
1%
R2532
390
SC_CVBS_IN
D2501
5.5V
EU
EU
Q2502
2SC3052
EU
Q2509
2SC3052
Selece = Low
EU
Q2510
2SC3052
L2507-*1
0
C2534
180pF
50V
OPT
R2551
75
1%
EU
DVT_OUT
Selece = High ==> A = B1

SC_FB
C
BLM18PG121SN1D
NON_DTV_OUT
CLOSE TO SOC
==> A = B0
E
R2515
COMP2_Pr
ID
JP2507
B_OUT
JP2508
8
7
AUDIO_L_IN
6
B_GND
0 EU
JP2509
R2516
5
AUDIO_GND
D2505
5.5V
EU
4
AUDIO_L_OUT
JP2510
COMP2_Y
EU
R2508
75
D2513
30V
1%
AUDIO_R_IN
REC_8
JP2511
0 EU
AUDIO_R_OUT
R2517
EU
R2539
9.1K
COMP2_Pb
D2506
5.5V
EU
JP2512
EU
R2509
75
1%
EU
SC_ID
OPT
D2512
30V
CLOSE TO JUNCTION
DA1R018H91E
JK2501
1/16W
1%
EU
R2542
1K
1%
C2528
1uF
10V
EU
C2537
1uF
25V
EU
10K/1K to match ADC Full-Scale range

22 EU
(1% of accruacy)
R2530
EU
SC/COMP2_L_IN
EU
R2510
470K
C2509
560pF
50V
EU
C2516
100pF
50V
EU
C2538
1uF
25V
D2507
5.6V
OPT
D2508
5.6V
OPT
22 EU
R2531
CLOSE TO SOC
SC/COMP2_R_IN
EU
EU
R2511
470K
CLOSE TO JACK
TP2501
C2510
560pF
50V
EU
CLOSE TO JUNCTION
INCM_VID_SC
C2517
100pF
50V
EU
C2533
0.1uF
16V
R2549
36
BLM18PG121SN1D
L2508
D2509
5.6V
OPT
DTV/MNT_L_OUT
EU
EU
C2518
1000pF
50V
EU
C2522
4700pF
BLM18PG121SN1D
L2509
D2510
5.6V
OPT
AUD_OUT
1K
R2519
OUT1
DTV/MNT_L_OUT
AUD_OUT
C2513
10uF
C2535
16V
AUD_OUT 6800pF
SCART1_Lout_N
L2501
5.6K
SCART1_Lout_P
C2520
33pF
AUD_OUT
IN1AUD_OUT
R2528
10K IN1+
VCC
IN2+
SCART1_Rout_P
5.6K
SCART1_Rout_N
AUD_OUT
5.6K
R2572
14
+12V
[SCART PIN 8]
[SCART AUDIO MUTE]

OUT4
13
12
11
10
IN4OPT
R2558
10K
OPT
R2552
4.7K
IN4+
+3.5V_ST
C
OPT
Q2508
2SC3052
R2570
AUD_OUT
C2501
0.1uF
50V
AUD_OUT
AUDIO_R
AUD_OUT
AUD_OUT
33K
R2526
50V
AUD_OUT
R2534
IC2501
LM324D
R2573
AUD_OUT
+12V
HOTEL_OPT
AUD_OUT >> EU/CHINA_HOTEL_OPT

5.6K
DTV/MNT_R_OUT
EU
C2523
4700pF
EU
C2519
1000pF
50V
EU
AUD_OUT
33K
R2527
R2571
AUD_OUT
R2529
10K
OUT2
AUD_OUT
R2518
1K
AUD_OUT
AUD_OUT C2521
33pF
DTV/MNT_R_OUT
C2514
10uF
CLOSE TO soc
THE

16V
AUD_OUT
AUD_OUT
R2524
IN2-
6800pF
OPT
R2561
12K
C
VEE/GND
DTV/MNT_L_OUT
EU
Q2503
2SC3052
IN3+
IN3-
EU
RT1P141C-T112
Q2505
EU
R2543
2K
R2548
10K
EU
SC_RE1
OPT
R2556
1K
REC_8
B
OPT
Q2507
E 2SC3052
SCART_MUTE
OUT3
DTV/MNT_R_OUT
EU
Q2504
2SC3052
1
2
EU
R2544
2K
C
OPT
Q2506
2SC3052
SC_RE2
OPT
R2557
1K
50V
BCM35230
SCART
25
NON CHB
TS Output
CHBO_TS_SERIAL
CHBO_TS_CLK
CHBO_TS_VAL_ERR
CHBO_TS_SYNC
CHB_RESET
THE

BCM35230
NON CHB
28
50
DUAL COMPONENT
China Hotel Option
Q2901
1ST : EBK61012601
2ND : 0TRDI80002A
+24V_AMP
P2901
12505WS-09A00
CN_HOTEL
R2904 0
CN_HOTEL
C2901
0.1uF
CN_HOTEL
AUDIO_R
+3.3V_Normal
4
CN_HOTEL
R2902
10K
CN_HOTEL
AMP_RESET_N
R2901 200
AMP_MUTE_HOTEL
CN_HOTEL
AMP_MUTE_HOTEL
C
R2903 0
Q2901
MMBT3904(NXP)
CN_HOTEL
E
SPK_R+_HOTEL
SPK_R-_HOTEL
9
10
THE
BCM35230
CHINA HOTEL
29
3D_SYNC
L_VS
THE

BCM35230
NON URSA
36
50
M1-*3

THE
SMD GASKET 6.5T
M2-*6
M23
MDS62110213
M1
MDS61887710
GASKET_9.5T
M12-*6
MDS61887710
GASKET_9.5T
M11-*6
MDS61887710
GASKET_9.5T
M10-*6
MDS62110209
GASKET_8.5T
M12-*5
MDS62110209
GASKET_8.5T
M11-*5
MDS62110209
GASKET_8.5T
M10-*5
MDS62110209
GASKET_8.5T
M9-*5
MDS62110205
GASKET_7.5T
M12-*4
MDS62110205
GASKET_7.5T
M11-*4
MDS62110205
GASKET_7.5T
M10-*4
M9-*4
MDS62110205
GASKET_7.5T
M8-*4
MDS62110205
GASKET_7.5T
M7-*4
MDS62110205
GASKET_7.5T
M6-*4
MDS62110205
GASKET_7.5T
M5-*4
MDS62110205
GASKET_7.5T
M4-*4
MDS62110205
GASKET_7.5T
M3-*4
MDS62110205
GASKET_7.5T
M2-*4
MDS62110205
GASKET_7.5T
M1-*4
MDS62110208
GASKET_4.5T
M12
MDS62110208
GASKET_4.5T
M11
MDS62110208
GASKET_4.5T
M10
MDS62110208
GASKET_4.5T
M9
MDS62110208
GASKET_4.5T
M8
MDS62110208
GASKET_4.5T
M7
MDS62110208
GASKET_4.5T
M6
MDS62110208
GASKET_4.5T
M5
MDS62110208
GASKET_4.5T
M4
MDS62110208
GASKET_4.5T
M3
MDS62110208
GASKET_4.5T
M2
GASKET_4.5T
MDS62110208
MDS62110205
GASKET_7.5T
SMD GASKET 9.5T
MDS61887710
GASKET_9.5T
MDS62110209
GASKET_8.5T
M8-*5
MDS62110209
GASKET_8.5T
M7-*5
MDS62110209
GASKET_8.5T
M6-*5
MDS62110209
GASKET_8.5T
M5-*5
MDS62110209
GASKET_8.5T
M4-*5
MDS62110209
GASKET_8.5T
M3-*5
MDS62110209
GASKET_8.5T
M2-*5
MDS62110209
GASKET_8.5T
M1-*5
MDS62110210
GASKET_5.0T
M12-*1
MDS62110210
GASKET_5.0T
M11-*1
MDS62110210
GASKET_5.0T
M10-*1
MDS62110210
GASKET_5.0T
M9-*1
MDS62110210
GASKET_5.0T
M8-*1
MDS62110210
GASKET_5.0T
M7-*1
MDS62110210
GASKET_5.0T
M6-*1
MDS62110210
GASKET_5.0T
M5-*1
MDS62110210
GASKET_5.0T
M4-*1
MDS62110210
GASKET_5.0T
M3-*1
MDS62110210
GASKET_5.0T
M2-*1
SMD GASKET 8.5T
M9-*6
MDS61887710
GASKET_9.5T
M8-*6
MDS61887710
GASKET_9.5T
M7-*6
MDS61887710
GASKET_9.5T
M6-*6
MDS61887710
GASKET_9.5T
M5-*6
MDS61887710
GASKET_9.5T
M22
GASKET3.5T_HEATSINK
M4-*6
MDS61887710
GASKET_9.5T
M3-*6
MDS61887710
GASKET_9.5T
MDS62110213
GASKET3.5T_HEATSINK
M21
MDS62110213
GASKET3.5T_HEATSINK
M20
SMD GASKET 5.5T
MDS61887710
GASKET_9.5T
M1-*6
MDS62110204
GASKET_5.5T
M12-*2
MDS62110204
GASKET_5.5T
M11-*2
MDS62110204
GASKET_5.5T
M10-*2
MDS62110204
GASKET_5.5T
M9-*2
MDS62110204
GASKET_5.5T
M8-*2
MDS62110204
GASKET_5.5T
M7-*2
MDS62110204
GASKET_5.5T
M6-*2
MDS62110204
GASKET_5.5T
M5-*2
MDS62110204
GASKET_5.5T
M4-*2
MDS62110204
GASKET_5.5T
M3-*2
MDS62110204
GASKET_5.5T
M2-*2
M1-*1
MDS62110210
GASKET_5.0T
SMD GASKET 4.5T
MDS62110213
M1-*2
MDS62110204
GASKET_5.5T
SMD GASKET 5.0T
GASKET3.5T_HEATSINK
MDS62110206
GASKET_6.5T
M12-*3
MDS62110206
GASKET_6.5T
M11-*3
MDS62110206
GASKET_6.5T
M10-*3
MDS62110206
GASKET_6.5T
M9-*3
MDS62110206
GASKET_6.5T
M8-*3
MDS62110206
GASKET_6.5T
M7-*3
MDS62110206
GASKET_6.5T
M6-*3
MDS62110206
GASKET_6.5T
M5-*3
MDS62110206
GASKET_6.5T
M4-*3
MDS62110206
GASKET_6.5T
M3-*3
MDS62110206
GASKET_6.5T
M2-*3
MDS62110206
GASKET_6.5T
SMD GASKET
SMD GASKET 7.5T
BCM35230
SMD GASKET
2010. 09. 18
56
56
M13-*2
THE

M14-*5
MDS62110209
GASKET_8.5T
M15-*5
SMD GASKET 5.5T
MDS62110209
GASKET_8.5T
M14-*1
MDS62110205
GASKET_7.5T
M15-*4
MDS62110205
GASKET_7.5T
M14-*4
MDS62110205
GASKET_7.5T
M13-*4
MDS62110210
GASKET_5.0T
M15-*1
MDS62110210
GASKET_5.0T
SMD GASKET 5.0T
MDS62110209
GASKET_8.5T
M13-*1
MDS62110210
GASKET_5.0T
M13
MDS61887710
GASKET_9.5T
M15-*6
MDS61887710
GASKET_9.5T
M14-*6
MDS61887710
GASKET_9.5T
SMD GASKET 6.5T
M13-*6
MDS62110206
GASKET_6.5T
M15-*3
MDS62110206
GASKET_6.5T
M14-*3
MDS62110206
GASKET_6.5T
M13-*3
MDS62110208
GASKET_4.5T
M15
MDS62110208
GASKET_4.5T
M14
GASKET_4.5T
MDS62110208
SMD GASKET 4.5T
M13-*5
MDS62110204
GASKET_5.5T
M15-*2
MDS62110204
GASKET_5.5T
M14-*2
MDS62110204
GASKET_5.5T
SMD GASKET (UNDER THE TUNER)
SMD GASKET 9.5T
SMD GASKET 7.5T
SMD GASKET 8.5T
BCM35230
TUNER SMD GASKET
2010. 09. 18
57
57
+12V
DUAL COMPONENT
FROM LIPS & POWER B/D

+3.5V_ST
RT1P141C-T112
Q501,Q504,
Q505,Q506
1ST : 0TRIY80001A
Q502
1ST : 0TRIH80004A, 2ND : EBK61012501, 3RD : 0TR102009AM
Q507
1ST : EBK60752501, 2ND : EBK61011501
IC502,IC503
1ST : EAN61151001, 2ND : EAN60670101
2ND : 0TR387500AA
PANEL_POWER
L511
TYP 1450mA
12V_PANEL
MLB-201209-0120P-N2
Q502
GND
15
16
GND/V-sync
12V
17
18
INV ON
12V
19
20
A.DIM
21
22
P.DIM1
23
24
Err OUT
12V
GND/P.DIM2
POWER_16_URSA_SCAN
R574
0
L/DIM0_VS
POWER_16_GND
P501
PANEL_CTL
POWER_20_A_DIM
R531
0
POWER_20_PWM_DIM
R538
0
ERROR_OUT_24
PWM_DIM
ERROR_OUT_PULL_UP
R523
4.7K
PWM_DIM_22
+3.5V_ST
+3.3V_Normal
R546
1K
ERROR_OUT
R551
10K
C
R543
PWM_DIM
R540 0
NON_OPC/NON_IOP
6.8K
OPT
R527 0
INV_CTL
0
R522
10K
OPT
IC503
NCP803SN293
VCC
PG
VCC
PD_+20V
R510-*4
5.6K
1%
PIN No
ESD
C520
0.1uF
16V
PD_24V
R510
8.2K
1%
PD_+18.5V
R511-*3
1.21K
1%
PD_24V
R511
1.5K
1%
LGD
AUO
SHARP
INV_ON
INV_ON
CMO(09)
NCP803SN293
C581
GND
0.1uF
16V
PD_+18.5_20_24V
R519
100
RESET
PD_+18.5_20_24V
18
INV_ON
A-DIM
20
V4:VBR-A
V5:NC
NC
22
PWM_DIM PWM_DIM
Err_out
LED:GND
24
PD_+18.5_20_24V
IC502
VCC
PD_+20V
R511-*4
1.3K
1%
POWER_ON/OFF1
EN
A-DIM
INV_ON
IC505
TPS54425PWPR
14
C502
10uF
16V
OPT
C501
10uF
16V
L502
Max 7350 mA
R562
0
VBST
1/10W
5%
C511
0.1uF
50V
Placed on SMD-TOP
SW2
SW1
PGND2
C505
10uF
16V
PGND1
13
15
VIN1
C535
0.1uF
50V
OPT
THERMAL
+12V
C504
100pF
50V
S_3
S_2
S_1
12
10
Placed on SMD-TOP
VREG5
R2
C512
1uF
25V
SS
R530
33K
1%
R521
0
GND
C507
1000pF
50V R506
330
PGD
LDRV
C522
22uF
10V
BP5
R578
C513
0.1uF
16V
S_2
S_1
EN
R514
OPT
C523
22uF
10V
OPT
C524
47uF
10V
+2.5V_BCM35230
C525
10uF
10V
IC504
AP2132MP-2.5TRG1
3A
LX_1
EN
POWER_ON/OFF2_1
FB
R564 12K
COMP
C557
2200pF
C595
22pF
50V
OPT
C559
0.1uF
16V
C570
22uF
16V
C568
22uF
10V
R1
C565
100pF
50V
OPT
10K
R2
POWER_ON/OFF2_2
+3.3V_Normal
Vout=0.8*(1+R1/R2)
C518
22uF
10V
Switching freq: 500K
+5V_USB+WIFI
MAX 1.9A
+12V
+5V_USB
IC506
MP8706EN-C247-LF-Z
+2.5V_BCM35230
Max 960 mA
IN
SW_1
1
POWER_ON/OFF2_1
OPT
R528
10K
PG
2
EN
AON7200
Q508
C527
10uF
0.9V_CORE_FB
+5V_Normal
6.3V
C533
0.1uF
OPT
C521
10uF
25V
8
GND
7
ADJ
6
R544
18K R2
1%
2A
SW_2
C526
0.1uF
R545
56K R1
1%
R539
22
VOUT
VIN
GND
[EP]
+3.5V_ST
R505
6.8K
1% R1
L513
4.7
S_3
L516
3.6uH
LX_2
R566
10K
CIC21J501NE
R536
10K
R507
10K OPT
VDD
Vout=0.8*(1+R1/R2)
1uH
R525
330
1%
C514
3300pF
50V
R509
100K
PG
R1
AGND
C546
10uF
16V
L505
+5V_Normal
NR8040T3R6N
BOOT
PGND
R534
10K
VFB
1%
4A
11
L514
BLM18PG121SN1D
VIN
2
MAX 1A
IC507
AOZ1073AIL-3
+3.3V_Normal
THERMAL
R2
MAX 2.8A
C517
22uF
10V
120-ohm
L506
SW
4.7
50V
220pF
+3.3V_Normal
TEST
COMP
C516
4.7uF
10V
C509
R577
C515
0.47uF
25V
C510
0.01uF
50V
11
FB
R504
2K
HDRV
C591
0.1uF
16V
L508
2uH
EP_GND
10
THERMAL
0.9V_CORE_FB
C594
22uF
10V
Vout=0.8*(1+R1/R2)
+0.9V_CORE
ENABLE
R593
3.9K
1%
+5V_Normal
R503
IC501
TPS40192DRCR
C593
560pF
50V
R592
1K
1%
GND
VO
Q503
AON7430
1K
GND
PWM_DIM
PWM_DIM
C537
0.1uF
OPT
R572
10K
[EP]PGND
VIN2
SS
Err_out Err_out
+3.3V_NORMAL
L507
BLM18PG121SN1D
+0.9V_CORE_BCM35230
POWER_ON/OFF2_2
R595
4.3K
1%
1.5A
R591
10K
+12V
C503
10uF
16V
R1
FB
CHECK PWR/MODULE PIN MAP

15V-->3.6V
20V-->3.5V
24V-->3.48V
12V-->3.58V
ST_3.5V-->3.5V
+12V
BLM18PG121SN1D
OUT
C590
10uF
10V
GND
not to RESET at 8kV ESD

PD_+18.5V
R510-*3
4.7K
1%
POWER_DET
PD_+18.5_20_24V
R516
100K
+24V
ERROR_OUT
<OS MODULE PIN MAP>
R520
100
RESET
IN
R537
R541
0
POWER_24_ERROR_OUT
C580
0.1uF
16V
PD_+12V
R513
1.21K
1%
R524
+3.5V_ST
100
+1.5V_DDR
[EP]
BLM18PG121SN1D
POWER_24_INV_CTL
POWER_24_GND
R517
100K
IC508
AP7173-SPG-13 HF(DIODES)
L517
R552
10K
OPT
POWER_24_PWM_DIM
ERROR_OUT_24
Max 800mA
+3.5V_ST
R547
10K
Q504
2SC3052
Power_DET
+1.5V_DDR
OPT
A_DIM
POWER_22_PWM_DIM
R526 0
PD_+3.5V
R515
0
5%
1/8W
2K
POWER_22_A_DIM
R535
0
PD_+12V
R512
2.7K
1%
R557
22K
Q505
2SC3052
A_DIM
R529
0
POWER_20_ERROR_OUT
+3.5V_ST
Q506
2SC3052
+3.3V_Normal
#16/#20/#23
LD - GND OR USE
LE(N.L.D.) - OPEN
LE(L.D.) - USE
+12V
R553
47K
B
A_DIM
A_DIM_20
25
POWER_18_A_DIM
R533
PWM_DIM_22
SMAW200-H24S2
OPT
R554
10K
POWER_18_INV_CTL
INV_CTL_18
INV_CTL_18
A_DIM_20
SLIM_32~55
C506
0.1uF
50V
R532
100
L_VS
R573
0
POWER_16_BCM_SCAN
1/8W
2K
PANEL_DISCHARGE_REG
R576
3.5V
14
GND
C563
0.1uF
50V
1%
12
13
R570
51K
10
11
1%
GND
R555
22K
PANEL_DISCHARGE_REG
R575
3.5V
3.5V
+12V
OS Module OPT
C519
0.1uF
50V
R571
3.6K
GND
1%
GND
C560
OPT 1uF
25V
BST
3A
C528
1uF
50V
VCC
OPT
C529
100pF
50V
R1
R542
10K
FB
EN/SYNC
POWER_ON/OFF2_1
R548
10K
EAN31346002
1%
C552
10uF
25V
R549
33K
GND
GND
L504
MLB-201209-0120P-N2
C530
100pF
50V
OPT
C532
22uF
10V
C534
0.1uF
16V
C536
0.1uF
16V
1%
24V
3.5V
C508
0.1uF
16V
L501
MLB-201209-0120P-N2
24V
R550
6.2K
L503
MLB-201209-0120P-N2
R558
R559
10K
1.8K
12V_PANEL12V_PANEL
+3.5V_ST
PWR ON 1
24V
3
Q507
AO3407A
+24V
THERMAL
2
Q501
2SC3052
PANEL_VCC
C551
0.1uF
50V
C550
0.01uF
50V
5V_PANEL
R558-*1
22K
NORMAL_26~55
P502
FW20020-24S
5V_PANEL
R559-*1
2.7K
R502
10K
RL_ON
R518
0
R508
4.7K
R2
5
NC
VCTRL
EAN61387601
C538
47uF
10V
C539
10uF
6.3V
L509
3.6uH
NR8040T3R6N
R501
12K
1%
Vout=(1+R1/R2)*0.8
R2
Vout=0.591*(1+R1/R2) Switching
freq: 600K
C531
1uF
OPT
Vout=0.6*(1+R1/R2)
THE

Vout=0.8*(1+R1/R2)
BCM35230
POWER
58
3D Encoding Format

3D Format Processing
Full Resolution Support
BD Disk
BD Player
3D Video I/F
Source
L : 1920x1080p/30Hz
R : 1920x1080p/30Hz
(L-R)
Encoding
L : MPEG-4 AVC
R : MPEG-4 MVC
RL
R
R
R
Decoding
L : 1920x1080p/30Hz
R : 1920x1080p/30Hz
Glasses
Passive Type Display
L
L
3D Ready TV
Active Type Display
HDMI 1.3 Tx
L : 1920x1080p/30Hz
R : 1920x1080p/30Hz
HDMI 1.4 Tx
L : 1920x1080p/60Hz
R : 1920x1080p/60Hz

3DTV System
Passive Type
RF
Component
RGB
USB
DTV Main
Board
URSA5
120P
DTV
SoC
BD Player
FRC
2D to 3D
LVDS
LCD
120Hz panel
HDMI 1.3/
HDMI 1.4
Active Type
RF
Component
RGB
USB
BD Player
DTV Main
board
DTV
SoC
HDMI 1.3/
HDMI 1.4

FRC Sub board
LG1131A LG1121 LG5811

(2D to 3D)
(FRC2)
(XTR
T-con)
LCD
240Hz Panel
Mini
LVDS
3D with Active glasses

DLP, PDP
Double refresh rate LCD

Data doubling
L close
R open
L open
R close
L close
3D Sync signal
R close
LCD
Black insertion
L open
R close
R open
L open
L open
R close
L close
R open
L open
R close
3D Sync signal
Big Crosstalk because of driving system

L open
R close
L close
R open
L open
R close
The duration without crosstalk can be made
Backlight blinking and Shutter glasses
3D sync
Backlight
signal
LEFT OPEN
OFF
ON
RIGHT OPEN
OFF
ON
Dont need to control open time in Glasses

Backlight Scanning and Glasses
3D sync
LEFT OPEN
RIGHT OPEN
Backlight
Scanning signal
Dont need to control open time in Glasses
GP3 Backend block diagram (SG)
+3.3VD
Vol.
Vol.Regulator
Regulator
(TPS51200)
(TPS51200)
DDR0_A[12:0]/
BA[2:0]/CLK/CKE
+0.75V_VTT0
XTAL_IN
DDR3
DDR3 SDRAM
SDRAM
-- 1Gbit
1Gbit(x16)
(x16)
Vol.
Vol.Regulator
Regulator
(TPS51200)
(TPS51200)
+0.75V_VTT1
- -800MHz
800MHz
XTAL_OUT
DDR1_A[12:0]/
BA[2:0]/CLK/CKE
LG1121
VLCD_POWER
P_VCOM/
VCOMLFB/
VCOMRFB
PMIC
PMIC
(TPS65168)
(TPS65168)
(0x42)
(0x42)
I2C_SCL
2Dto3D
(0x8E)
X-Tal
(24.75Mhz)
SPI_DI
DDR1_DATA[15:0]
SPI_DO/CK/CS
(0x1C, direct
0xB2, in-direct)
DPM/FLK
VLCD_POWER
+1.0VD
DDR0_DATA[15:0]
+1.5V1
DC-DC
DC-DCConverter
Converter
(AOZ1072AI)
(AOZ1072AI)
+1.5V1
R_VS, M2_SCLK/MOSI
- -800MHz
800MHz
+1.5V0
FRC_RESET
DDR3
DDR3 SDRAM
SDRAM
-- 1Gbit
1Gbit(x16)
(x16)
3D_SYNC_OUT
DC-DC
DC-DCConverter
Converter +1.5V0
(AOZ1072AI)
(AOZ1072AI)
VLCD_POWER
(+12V)
+3.3VD
I2C_SDA
51Pin LVDS Input
DC-DC
DC-DCConverter
Converter
(AOZ1072AI)
(AOZ1072AI)
I2C_SCL
I2C_SDA
SPI
SPIFLASH
FLASH
(4Mbit)
(4Mbit)
Dual-link LVDS(@74.25MHz)
I2C_SCL
FRC_RESET
I2C_SDA
3D_SYNC_OUT
VLCD_POWER
VCC_LCM/VDD_LCM/
VGH/VGL/HVDD/VCORE
+1.0V
Octa-link LVDS
DC-DC
DC-DCConverter
Converter
(AOZ1024DI)
(AOZ1024DI)
VCOMLOUT/
VCOMROUT
I2C_SCL
I2C_SDA
Dual-link HF mini-LVDS
(@297MHz)
XTR
T-Con
(0x72)
I2C_TCON_SCL
I2C_TCON_SDA
VLCD_POWER
EEPROM
EEPROM
(64kbit)
(64kbit)
+3.3VD
Dual-link HF mini-LVDS
(@297MHz)
+3.3VD
+2.5V
VCC_LCM/VDD_LCM/
HVDD
GMA[18:15],
GMA[9:5]
I2C_SCL
P-GAMMA
P-GAMMA
IC
IC
P_VCOM
I2C_SDA (MAX9668B)
(MAX9668B)
(0xE8)
(0xE8)
DC-DC
DC-DCConverter
Converter
(AOZ1072AI)
(AOZ1072AI)
LDO
LDORegulator
Regulator
(AP2132MP)
(AP2132MP)
VCC_LCM/VDD_LCM/
HVDD
GMA[14:10],
GMA[4:1]
I2C_SCL
P-GAMMA
P-GAMMA
IC
IC
I2C_SDA (MAX9668B)
(MAX9668B)
(0xEA)
(0xEA)
Z_OUT
80P mini-LVDS Output

RIGHT
80P mini-LVDS Output

LEFT
GP3 Backend block diagram (PG)

BCM35230
XTAL_IN
XTAL_OUT
DDR3
DDR3 SDRAM
SDRAM
-- 1Gbit
1Gbit (x16)
(x16)
-- 800MHz
800MHz
DDR1_A[12:0]/
BA[2:0]/CLK/CKE
DDR1_DATA[15:0]
URSA5
(0xB4)
SPI_DI
+12VD
DC-DC
DC-DC Converter
Converter
(AOZ1072AI)
(AOZ1072AI)
LVDS data from

Main IC
( BCM35230 )
X-Tal
(24.75Mhz)
SPI_DO/CK/CS
SPI
SPI FLASH
FLASH
(4Mbit)
(4Mbit)
0X98
0X98
+3.3V_FRC
Quad-link LVDS(@74.25MHz)
+3.3VD
+12VD
DC-DC
DC-DC Converter
Converter
(AOZ1072AI)
(AOZ1072AI)
+1.5V
+1.26V_FRC
LDO
LDO Regulator
Regulator
(AP7173-SPG-13)
(AP7173-SPG-13)
51Pin LVDS output

41Pin LVDS output
Repair Guide for BCM Chassis

Model : **LW77/9500-TA, **LW57/6500-TA, **LV5500-TA
Contents
0. ALEF & Edge LED, Overview models
1. Tool Option Information
2. Area Option Information
3. Main PCB for BroadBand
4. Formatter PCB for BroadBand
5. Block Diagram
6. Inner Connection
7. Repair Process (Troubleshooting)
JAN. 13th, 2011
LG Electronics/ LCD TV
By M.R.VIJAYSHANKAR

LED - ALEF
Benefit:MoreClearMoreReal
Feature
ALEFType
LocalDimming
ALEFLED`
Bestpicturequality+thinTV
Slimmerdepth
betterpicturequality
Local Localdimmingdepictsmore
Dimming deepblack.
DBEF
Prism sheets
Diffuser plate
BLU
structure
Light Blocking Pattern

Guiding Layer
Reflecting coating w/patterns
PCB
Local
Dimming

LED Array is on the back of Module
Model
XXLW9500-TA
47inch : H(24) * V(10) = 240Block
55inch : H(24) * V(12) = 288Block
XXLW7700-TA
42inch : H(12) * V(4) = 48Block
47inch : H(12) * V(5) = 60Block
55inch : H(16) * V(6) = 96Block
LED - Edge
Benefit:MoreClearMoreReal
Feature
EdgeType
w/LocalDimming
LED Array
BLU
structure
EdgeLED Bestpicturequality+thinTV
Local Localdimmingdepictsmore
Dimming deepblack.
Model
Upper
Metal
Cover
XXLV5500-TA
XXLW6500-TA
XXLW5700-TA
LED Array is on the side of Module
Local
Dimming

32inch : H(2) * V(5) = 10Block

37inch : H(2) * V(5) = 10Block
42inch : H(2) * V(8) = 16Block
47inch : H(2) * V(8) = 16Block
55inch : H(2) * V(8) = 16Block

MODEL
TOOL 1
TOOL 2
TOOL 3
TOOL 4
TOOL 5
TOOL 6
Etc.
47LW9500-TA
33112
4811
3327
35003
47695
696
STD B/L : 65
55LW9500-TA
33115
4811
3327
35003
47695
694
STD B/L : 55
47LW7700-TA
33080
4811
3327
51387
14925
662
STD B/L : 55
55LW7700-TA
33083
4811
3327
51387
14925
8855
STD B/L : 60
PWM : Max_10%
TOOL 1
Setting
Inch
47 / 55
Tool
LW95 / LW77
TOOL 3
Setting
TOOL 5
EMF(JPEG, MP3)
WiFi
Divx
WiFi Builtin
Setting
1
1/0
STD Backlight
USB Count
65/55/70/70
2
LGD
DivX Plus
Skype
LVDS Bit
10 Bit
DLNA
Motion Remocon
BuiltIn
TOOL 2
Setting
Digital Eye
Channel Browser
Audio P/W Volt
24V
Headphone
Set ID
Speaker Watt.
10W
Wireless Ready
Mirror Mode
Max Pwm
DVR Ready
Orange Service
3D THX
THX
NetCast Service
THX Media
Director
CNETV
Picture Wizard
ISF
11
Audio ADC Index
11
LocalDim Menu
Module Ver.
TOOL 4
Local Dimming
PSU Power
Digital Demod
Analog Demod
V6
Setting
DVB_BCM
LGT10
Energy Star
OFF
HDMI Switch IC
SIL
Audio Amp.
NTP2AMP
Scart Count
None
Backlight Tyype
ALEF_LED/
ALEF_LGD
Display Port

3D Display Type
3D
2D To 3D
ON
App Store
Panel Error Out

Scanning B/L
USB Hub Count
Setting
Maker
Video ADC Index
TOOL 6
USB Swap
1/1/0/0
0
Default
0
OFF
ON/OFF

MODEL
TOOL 1
TOOL 2
TOOL 3
TOOL 4
TOOL 5
TOOL 6
Etc.
42LW6500-TA
33030
4811
3327
17593
47701
727
STD B/L : 60
47LW6500-TA
33032
4811
3327
17593
47701
726
STD B/L : 55
55LW6500-TA
33035
4811
3327
17593
47701
727
STD B/L : 60
42LW5700-TA
33190
4811
3327
17593
14933
727
STD B/L : 60
47LW5700-TA
33192
4811
3327
17593
14933
726
STD B/L : 55
32LV5500-TA
32996
715
3327
17594
8789
663
STD B/L : 60
32LV5500-TA
(CMI)
35044
715
3327
17594
8917
665
37LV5500-TA
32997
715
3327
17594
8789
663
37LV5500-TA
(AUO)
37093
715
3327
17594
8917
665
42LV5500-TA
32998
715
3327
17592
8789
662
42LV5500-TA
(AUO)
37094
715
3327
17592
8917
665
47LV5500-TA
33000
715
3327
17592
8789
663
STD B/L : 60
55LV5500-TA
33003
715
3327
17592
8789
664
STD B/L : 65
55LV5500-TA
(AUO)
37099
715
3327
17592
8917
665

STD B/L : 55
2. Area Option Information

3. Main PCB for Broadband

Main Features
Main Board (LW9500 & LW7700)
2
7
Main processor, DDR Memory, Flash Memory
Voltage (5V/3.3V/0.9V)
Voltage (2.5V/1.5V)
Voltage (1.25V)
HDMI switch (4:1)
Audio AMP (Main)
Audio AMP (Woofer)
USB switch (2:1)
NEC MICOM
6
1
8
3
9


Cables

A
To Woofer
To Power Board
To Speaker
Not Use
To Formatter Board
To inner WiFi Assy (Only LW9500)
To IR + Soft Touch Assy
To Motion Remocon Receiver (RF Module)

4. Formatter PCB for Broadband

Main Features & Cables (LW9500 & LW7700)
4
B

2D to 3D IC
XTR IC
P-GAMMA IC
VOLTAGE
To Main Board (LVDS Cable)
To LED Driver Board (Master)
To LCD Module (LVDS 240Hz Cable)
To LCD Module (LVDS 240Hz Cable)
To LED Driver Board (Slave)
4
E
FRC, DDR Memory

Main Features

1
Main processor, DDR Memory, Flash Memory
Voltage (5V/3.3V/0.9V)
Voltage (2.5V/1.5V)
Voltage (1.25V)
HDMI switch (4:1)
Audio AMP (Main)
NEC MICOM
URSA5 EXTERNAL FRC
2
6
3
5


Cables

A
To Power Board (Local Dimming)
To Power Board
To Speaker
To Module 41P
To Module 51P
To IR + Soft Touch Assy

5. Block Diagram (SG LW95/77, LV55)

SYSTEM
DDR3 X 16 X 2
(2Gb)
NAND
Flash(8Gb)
SYSTEM EEPROM X 1
(1Mb)
DIF(+/-)
RF
TUNER
(DVB-T)
CVBS(M)
SIF
DVR ready
USB1
USB2
DVB-T
Demod
CVBS
AUDIO
51P
USB hub (only LW9500)

USB
HUB IC
LVDS.
T-con
(FRCII)
Mini
LVDS
USB
WiFi
(built in)
Only LW9500
HDMI1
HDMI2
HDMI3
Side
(HDCP
HDMI
HUB IC
HDMI
S/W
I2S Out
EEPROM)
Audio
AMP
(Woofer)
HDMI4
H/P
L/R Out
A/V2
CVBS
COMP1
COMP
PC-RGB
PC-AUDIO
Bottom
side
OPTIC
I2C
I2C
Sub Micom
(sanyo)
Wireless Ready
L/R In
Ethernet
UART
M-Remote
Module
(built in)
Only LW9500/7700
A/V1
RS-232C
RGB,H/V
Only LW9500/7700
BCM
35230
SPDIF OUT
LAN
Audio
AMP
Rear
5. Block Diagram (LW65/57)

SYSTEM
DDR3 X 16 X 2
(2Gb)
NAND
Flash(8Gb)
SYSTEM EEPROM X 1
(1Mb)
DIF(+/-)
RF
TUNER
(DVB-T)
CVBS(M)
SIF
DVB-T
Demod
CVBS
AUDIO
51P
USB1
CAM,
DVR
Ready
USB2
HDMI1
HDMI2
HDMI3
LVDS.
USB
41P
Side
HDMI
HUB IC
(HDCP
HDMI
S/W
LG7303A
I2S Out
Audio
AMP
EEPROM)
HDMI4
H/P
L/R Out
A/V1
CVBS
COMP1
COMP
PC-RGB
PC-AUDIO
Rear
RGB,H/V
BCM
35230
I2C
I2C
Sub Micom
(NEC)
Wireless Ready
L/R In
OPTIC
SPDIF OUT
LAN
Ethernet
UART
RS-232C
5. Block Diagram
Jack Interface
BCM35230
COMP2_R/G/B
[VI_SC_R1],[VI_SC_G1],[VI_SC_B1]
SPDIF
[SPDIF_OUT]
COMP1
COMP_Y
[COMP1_Y]
DSUB_R / G / B
[DSUB_R+/G+/B+]
COMP_PB
[COMP1_Pb]
DSUB_ V / HSYNC
[DSUB_V/H SYNC]
EDID EEPROM
AT24C02BN-10SU-1.8
RGB_DDC_SCL
RGB_DDC_SDA
COMP_PR
[COMP1_Pr]
[RGB_DDC_SCL]
[RGB_DDC_SDA]
[COMP1_DET]
COMP DET
[BSC_S_SCL]
[BSC_S_SDA]
[EDID_WP]
MICOM
RGB DET
AV1
[DSUB_DET] // GPIO
[PC_L_IN]
[AV1_R_IN]
[PC_R_IN]
[AV1_L_IN]
PC L,R
[AV1_CVBS_IN]
CVBS
[AV1_CVBS_DET]
HDMI2
HDMI3
AV DET
AV2
HDMI1
[AV1_R_IN]
HDMI
HUB IC
HDMI4

[HDMI0_-/+]
[AV1_L_IN]
[AV1_CVBS_IN]
[AV1_CVBS_DET]
R
L
CVBS
AV DET
Appendix. Block Diagram for Edge/ALEF Backlight

[ All in one main PCB for XXLW950T/W/S/G,XXLW770T/W/S/G ALEF LED Backlight]
FHD@60Hz
Dual-Link LVDS
Main SoC
(BCM)
2D-3D
(LGSIC)
FHD@60Hz
Dual-Link LVDS
FRC-II
(LG1121)
FHD@240Hz
Octa-Link LVDS
XTR T-Con
(LGSIC)
FHD@240Hz
Quad-Link
HF mini-LVDS
8
3D_Sync
SPI/Vsync
LED
LED BLU
BLU control
control
Vsync
RF Emitter
Active Type Display
m
om
c
RF sync t info
- V orma
-F
* For more information about 3D system, refer to the page 1 ~6

6. Interconnection - 1
47/55LW9500
2
[PCBs]
3
8
11
[Cables]
10
Main to Formatter
Main PCB
Formatter PCB
PSU
LED Driver
Soft Touch + IR
Motion Receiver (RF Module)
WiFi
Woofer
Speaker
11
Power to LED Driver
Main to PSU
Main to WiFi
Main to Woofer
Main to IR+Soft Touch
10
Formatter to LCD Module
Main to Speaker
Power to LED Driver
11
LED Driver to LCD Module

Main to Motion Receiver (RF Module)
47/55LW7700
[PCBs]
Main PCB
Formatter PCB
PSU
Control Button
IR
Motion Receiver (RF Module)
Woofer
Speaker
3
7
6
9
[Cables]
10
Main to Formatter
Power to LED Driver
Main to PSU
Main to Control Button
Main to Motion Receiver (RF Module)
Main to Woofer
Main to IR
10
Formatter to LCD Module
Main to Speaker
Power to LED Driver

6. Interconnection 1 sub PCB
47/55LW9500
Soft Touch + IR Key PCB

RF MOTION ASSY
SPK unit
Soft Touch
IR Key PCB
RF MOTION ASSY
WIFI ASSY
WIFI ASSY
To Main
6. Interconnection 2 sub PCB
IR PCB
47/55LW7700
Control Key PCB
SPK unit
IR Key PCB
Control key
RF MOTION ASSY
RF MOTION ASSY
To Main
XXLW6500-TA
XXLW5700-TA
[PCBs]
3
6
1
Main PCB
Power Board
Soft touch + IR Key PCB
[Cables]
T-con Driver
3

Main / PSU cable
Main / Module LVDS cable

41&51PIN
LED driver / PSU
15Pin (IR+Touch) Cable
SPK Cable
Local Dimming Cable
6.Interconnection - 4
[PCBs]
32/37LV5500-TA
Main PCB
Power Board

(LW570 only IR Assy)
LED Driver 1
2
2
[Cables]
T-con Driver
3

Main / PSU cable

41&51PIN
LED driver / PSU
SPK Cable
Local Dimming Cable
[PCBs]
42/47LV5500-TA
3
6
1
Main PCB
Power Board

(LV570 only IR Assy)
[Cables]
T-con Driver
3
Same interconnection LW or LV serise

in the 42/47
Main / PSU cable

41&51PIN
LED driver / PSU
SPK Cable
Local Dimming Cable
Interconnection sub PCB( LV/LW55/57/65 serise )
IR & Soft touch Key PCB

(LV/LW570 only IR Assy)
SPK unit
Control key
(LV/LW570)
LV/LW57 Serise
IR & Soft touch
Key PCB
(LV/LW570
only IR Assy)
LW65 serise
LV/LW55 Serise
LV/LW57 Serise
To Main
Contents of LCD TV Standard Repair Process

No.
Error symptom (High category)
Error symptom (Mid category)
Page
No video/Normal audio
No video/No audio
A. Video error
Video error, video lag/stop, fail tunning
3, 4
Color error
Vertical/Horizontal bar, residual image,

light spot, external device color error
No power
Off when on, off while viewing, power auto

on/off
No audio/Normal video
Wrecked audio/discontinuation/noise
10
10
No response in remote controller, key error,

recording error, memory error
11
External device recognition error
12
B. Power error
7
8
Remarks
C. Audio error
D. Function error
11
12
E. Noise
Circuit noise, mechanical noise
13
13
F. Exterior error
Exterior defect
14
First of all, Check whether there is SVC Bulletin in GCSC System for these model.
Standard Repair Process
Error
symptom
LCD TV
A. Video error
Established
date
No video/ Normal audio
Revised date
2010. 12 .14
1/14
First of all, Check whether all of cables between board is inserted properly or not.
(Main B/D Power B/D, LVDS Cable,Speaker Cable,IR B/D Cable,,,)
A1
No video
Normal audio
Normal
audio
A4
Check Back Light

On with naked eye
N
Move to No
video/No audio
On
Check Power
Board
12v,3.5v etc.
A2
Replace T-con
Board or module
And Adjust VCOM
A28
Repair Power
Board or parts
Check Power Board 24v output
Normal
voltage
Normal
voltage
Replace Inverter
or module
End
N
Repair Power
Board or parts
Precaution
A7 & A3
Always check & record S/W Version and White

Balance value before replacing the Main Board

Replace Main Board
Re-enter White Balance value
LCD TV
Error
symptom
A. Video error
Established
date
No video/ No audio
Revised date
2010. 12 .14
2/14
A4
No Video/
No audio
Check various
voltages of Power
Board ( 3.5V,12V,20V
or 24V)
Normal
voltage?
Check and
replace
MAIN B/D
End
Replace Power
Board and repair
parts

Error
symptom
LCD TV
A6
Check RF Signal level
Normal
Signal?
A. Picture Problem
Established
date
Picture broken/ Freezing
Revised date
Check whether other equipments have problem or not.

(By connecting RF Cable at other equipment)
DVD Player ,Set-Top-Box, Different maker TV etc`
MenuSetup Booster
A7
Check RF Cable
Connection
1. Reconnection
2. Install Booster
Normal
Picture?
Check
S/W Version
SVC
Bulletin?
N
N
3/14
. By using Digital signal level meter

. By using Diagnostics menu on OSD
( Menu Set up Support Signal Test )
- Signal strength (Normal : over 50%)
- Signal Quality (Normal: over 50%)
Normal
Picture?
2010. 12 .14
S/W Upgrade
Normal
Picture?
Close
N
Check
Tuner soldering
Contact with signal distributor

or broadcaster (Cable or Air)
Normal
Picture?
Booster menu
OnOff: Check
OffOn: Check
N
Replace
Main B/D
Y
Close
Close

Error
symptom
LCD TV
A6
Check RF Signal level
Normal
Signal?
N
A. Picture Problem (DVB-S/S2)
Established
date
Tuning fail, Picture broken/ Freezing
Revised date
2011. 01 .24
4/14
Check RF signal cable (DVB satellite signal or not)

Check whether other equipments have problem or not.
(By connecting RF Cable at other equipment)
Set-Top-Box, Different maker TV etc
Check satellite setting.

- Check LNB frequency.
Y
- Check satellite
- Check Satellite connection
(DiSEqC, motor, etc)
A7
Y
Normal
setting?
Check
S/W Version
SVC
Bulletin?
Check
Tuner soldering
Replace
Main B/D
S/W Upgrade
Contact with
signal distributor
or broadcaster
(Cable or Air)
Change satellite setting

(match with installed ANT)
Normal
Picture?
Y
Normal
Picture?
N
Close
Close
Y
Close

LCD TV
Error
symptom
A8
Check color by input
-External Input
-COMPONENT
-RGB
-HDMI/DVI
A. Video error
Established
date
Color error
Revised date
2010. 12 .14
5/14
A10/ A11
Color
error?
N
Check
and replace
Link Cable
(LVDS) and
contact
condition
Y
Color
error?
Color
error?
Replace Main B/D
N
End
Check error
color input
mode
A12
Check Test pattern
Replace module
External Input/
Component
error
Check
external
device and
cable
External device Y
/Cable
normal
Replace Main B/D
N
Request repair
for external
device/cable
N
RGB/
HDMI/DVI
error

Check external
device and
cable
External device Y
/Cable
normal
Replace Main B/D
LCD TV
Error
symptom
A. Video error
Established
date
Vertical / Horizontal bar, residual image,

light spot, external device color error
Revised date
2010. 12 .14
6/14
Vertical/Horizontal bar, residual image, light spot
Replace
Module
A8
A10/ A11
Check color condition by input

-External Input
-Component
-RGB
-HDMI/DVI
Screen Y
normal?
Check external
device
connection
condition
Screen N
normal?
A28
Request repair
for external
device
Replace
module
A12
Y
Normal?
Check and
replace Link
Cable
End
Screen
normal?
Replace Main B/D

(adjust VCOM)
For LGD panel
Replace Main
B/D
End
For other panel
Check Test pattern
External device screen error-Color error

Check S/W Version
Check N
version
Y
External
Input
error
Component
error
S/W Upgrade
Normal
screen?
Check screen
condition by
input
-External Input
-Component
-RGB
-HDMI/DVI
RGB
error
Y
HDMI/
DVI
End
Connect other external

device and cable
(Check normal operation of
External Input, Component,
RGB and HDMI/DVI by
connecting Jig, pattern
Generator ,Set-top Box etc.
Connect other external

device and cable
(Check normal operation of
External Input, Component,
RGB and HDMI/DVI by
connecting Jig, pattern
Generator ,Set-top Box etc.
N
Screen
normal?
Replace
Main B/D
Y
Request repair for
external device
Y
Screen
normal?
Replace
Main B/D
LCD TV
Error
symptom
B. Power error
Established
date
No power
Revised date
A17
Check
Power LED
. Stand-By: Red
. Operating: white
2010. 12 .14
7/14
A19
DC Power on
by pressing Power Key
On Remote control
Power LED
On?
N
Normal N
operation?
Check Power
On High
OK?
Replace
Power
B/D
Check Power cord

was inserted properly
Replace Main B/D
A4
Measure voltage of each output of Power B/D
N
Normal?
Y
Y
Close
Check ST-BY 3.5V
Normal
Y
voltage?
A18
Normal
voltage?
Replace Main B/D
N
Replace Power B/D
Replace Power
B/D

LCD TV
Error
symptom
B. Power error
Established
date
Off when on, off while viewing, power auto on/off
Revised date
2010. 12 .14
8/14
Check outlet
A22
Check A/C cord
Error?
Check Power Off

Mode
CPU
Abnormal
Normal?
Replace Main B/D
End
N
Check for all 3- phase
power out
Abnormal
1
A19
Fix A/C cord & Outlet

and check each 3
phase out
(If Power Off mode

is not displayed)
Check Power B/D
voltage
Caution
Check and fix exterior
of Power B/D Part
* Please refer to the all cases which

can be displayed on power off mode.

Replace Power B/D
Status
Normal
voltage?
Replace Main B/D
N
Replace Power B/D
Power off List

"POWEROFF_REMOTEKEY"
"POWEROFF_OFFTIMER"
"POWEROFF_SLEEPTIMER"
"POWEROFF_INSTOP"
"POWEROFF_AUTOOFF"
Normal "POWEROFF_ONTIMER"
"POWEROFF_RS232C"
"POWEROFF_RESREC"
"POWEROFF_RECEND"
"POWEROFF_SWDOWN"
"POWEROFF_UNKNOWN"
"POWEROFF_ABNORMAL1"
Abnormal
"POWEROFF_CPUABNORMAL"
Explanation
Power off by REMOTE CONTROL
Power off by OFF TIMER
Power off by SLEEP TIMER
Power off by INSTOP KEY
Power off by AUTO OFF
Power off by ON TIMER
Power off by RS232C
Power off by Reservated Record
Power off by End of Recording
Power off by S/W Download
Power off by unknown status except listed case
Power off by abnormal status except CPU trouble
Power off by CPU Abnormal
LCD TV
Error
symptom
C. Audio error
Established
date
No audio/ Normal video
Revised date
A24
No audio
Screen normal
Check user
menu >
Speaker off
2010. 12 .14
9/14
A25
N
Off
Check audio B+
24V of Power
Board
Normal
voltage
Cancel OFF
Check
Speaker
disconnection
Replace Power Board and repair parts
N
Disconnection
Replace MAIN Board
End
Y
Replace Speaker

LCD TV
Error
symptom
C. Audio error
Established
date
Wrecked audio/ discontinuation/noise
Revised date
2010. 12 .14
10/14
abnormal audio/discontinuation/noise is same after Check input signal compared to No audio

A25
Check input
signal
-RF
-External Input
signal
Wrecked audio/
Discontinuation/
Noise for
all audio
Signal
normal?
Check and replace

speaker and
connector
Check audio
B+ Voltage (24V)
Y
Wrecked audio/
Discontinuation/
Noise only
for D-TV
Normal
voltage?
Replace Main B/D

N
Wrecked audio/
Discontinuation/
Noise only
for Analog
(When RF signal is not
received)
Request repair to external
cable/ANT provider
(In case of
External Input
signal error)
Check and fix
external device
Replace Power B/D
Replace Main B/D
Wrecked audio/
Discontinuation/
Noise only
for External Input
Connect and check
other external
device
Normal
audio?
End
Y
Check and fix external device

10
Error
symptom
LCD TV
D. General Function Problem
Established
date
Remote control & Local switch checking
Revised date
2010. 12 .14
11/14
1. Remote control(R/C) operating error

A27
Check R/C itself
Operation
Normal Y
operating?
A27
Check & Repair

Cable connection
Connector solder
N
Check R/C Operating
When turn off light
in room
If R/C operate,
Explain the customer
cause is interference
from light in room.
Normal
operating?
A27
Check B+
3.5V
On Main B/D
A4
Close
Check & Replace

Baterry of R/C
Normal
operating?
Replace
Main B/D
Normal
Voltage?
Check IR
Output signal
Check 3.5v on Power B/D

Replace Power B/D or
Replace Main B/D
(Power B/D dont have problem)
Normal
Signal?
N
Repair/Replace
IR B/D
Close
N
Replace R/C

11
LCD TV
Check
input
signal
Error
symptom
Y
Signal
input?
N
Established
date
External device recognition error
Revised date
Check technical
information
- Fix information
- S/W Version
Check and fix

external device/cable

D. Function error
Technical
information?
External Input and

Component
Recognition error
2010. 12 .14
12/14
Replace Main B/D
Fix in
accordance
with technical
information
12
RGB,HDMI/
DVI, Optical
Recognition error
Replace Main B/D
LCD TV
Identify
nose
type
Error
symptom
Circuit
noise
Mechanical
noise
E. Noise
Established
date
Circuit noise, mechanical noise
Revised date
Check
location of
noise
13/14
Replace PSU(with LED driver)

OR
Replace LED driver
Check location
of noise
Mechanical noise is a natural

phenomenon, and apply the 1st level
description. When the customer does not
agree, apply the process by stage.
Describe the basis of the description
in Part related to nose in the Owners
Manual.

2010. 12 .14
OR
OR
13
When the nose is severe, replace the module

(For models with fix information, upgrade the
S/W or provide the description)
If there is a Tak Tak noise from the
cabinet, refer to the KMS fix information and
then proceed as shown in the solution manual
(For models without any fix information,
provide the description)
LCD TV
F. Exterior defect
Error
symptom
Zoom part with

exterior damage
Exterior defect
Module
damage
Replace module
Established
date
Revised date
2010. 12 .14
14/14
Adjust VCOM
A28
Cabinet
damage
Remote
controller
damage
Stand
dent

Replace cabinet
Replace remote controller
Replace stand
14
Contents of LCD TV Standard Repair Process Detail Technical Manual

No.
Error symptom
Content
Page
Check LCD back light with naked eye
A1
LED driver B+ 24V measuring method
A2
Check White Balance value
A3
Power Board voltage measuring method
A4
TUNER input signal strength checking method
A6
LCD-TV Version checking method
A7
LCD TV connection diagram
A8
10
Tuner Checking Part
A9
11
Check Link Cable (LVDS) reconnection

condition
A10
A11
12
Adjustment Test pattern - ADJ Key
A12
13
LCD TV connection diagram
A8
Check Link Cable (LVDS) reconnection

condition
A10
A11
15
A12
16
Exchange T-Con Board (1)
A-1/5
Exchange T-Con Board (2)
A-2/5
Exchange LED driver Board (PSU)
A-3/5
Exchange Module itself (1)
A-4/5
Exchange Module itself (2)
A-5/5
Remarks
A. Video error_ No video/Normal audio
6
A. Video error_ No video/Video lag/stop
A. Video error_Color error
14
17
18
19
A. Video error_Vertical/Horizontal bar,

residual image, light spot
<Appendix>
Defected Type caused by T-Con/
Inverter/ Module
20

A10 : LVDS
A11 : Driver bd
Continue to the next page

Contents of LCD TV Standard Repair Process Detail Technical Manual

Continued from previous page
No.
Error symptom
Content
Page
21
Check front display LED
A17
22
Check power input Voltage & ST-BY 5V
A18
Checking method when power is ON
A19
POWER BOARD voltage measuring method
A4
23
B. Power error_No power
24
Remarks
25
26
B. Power error_Off when on, off while

viewing
POWER OFF MODE checking method
A22
27
B. Power error_Off when on, off while

viewing
POWER BOARD PIN voltage checking

method
A19
Checking method in menu when there is no

audio
A24
Voltage and speaker checking method when

there is no audio
A25
28
C. Audio error_No audio/Normal video
29
30
C. Audio error_Wrecked
audio/discontinuation
Voltage and speaker checking method in

case of audio error
A25
31
D. Function error_ No response in

remote controller, key error
Remote controller operation checking

method
A27
32
D. VCOM Adjustment
Sequence of the Vcom adjustment
A28

Standard Repair Process Detail Technical Manual

LCD TV
Error
symptom
A. Video error_No video/Normal audio
Content
Check LCD back light with naked eye
<XXLW950X MODELS>
Established
date
Revised
date
2010. 12 .14
A1
<XXLW770X MODELS>
After turning on the power and disassembling the case, check with the naked eye,
whether you can see light from module
A1

LCD TV
Error
symptom
Content
LED driver B+ 24V measuring method
Established
date
Revised
date
2010. 12 .14
A2
Check the DC 24V, 12V, 3.5V and Inverter on

ALEF LED
P202
Edge LED

P203
1~5
24V
1~5
24V
6~10
GND
6~10
GND
11
Error
11
Error
12
Inverter ON
12
Inverter ON
13
A-dim
13
A-dim
14
P-dim
14
P-dim
A2

LCD TV
Error
symptom
Content
Check White Balance value
Established
2010. 12 .14
date
Revised
date
A3
<ALL MODELS>
Entry method
method
Entry
1.
1. Press
Press the
the ADJ
ADJ button
button on
on the
the remote
remote controller
controller for
for adjustment.
adjustment.
2.
2. Enter
Enter into
into White
White Balance
Balance of
of item
item 6.
7.
3.
3. After
After recording
recording the
the R,
R, G,
G, B
B (GAIN,
(GAIN, Cut)
Cut) value
value of
of Color
Color Temp
Temp
(Cool/Medium/Warm),
re-enter
the
value
after
replacing
(Cool/Medium/Warm), re-enter the value after replacing the
the MAIN
MAIN BOARD.
BOARD.
A3

LCD TV
Error
symptom
A. Video error_No video/ Audio
Content
Power Board voltage measuring method
ALEF LED
Established
2010. 12 .14
date
Revised
date
A4
Check the DC 24V, 12V, 3.5V.

24 Pin (Power Board Main Board) -
SMAW200-H24S (YEONHO)
Edge LED
Power on
20V (24V)
20V (24V)
20V (24V)
GND
GND
GND
GND
3.5V
10
3.5V
11
3.5V
12
3.5V
13
GND
14
GND
15
GND
16
GND
17
12V
18
Inverter On/off
19
12V
20
Lamp : A-Dim
LED : N.C
21
12V
22
PWM Dim #1
24
Error-out
23

N.C
Lamp SCANNING Model
: PWM Dim #2
A4

LCD TV
Error
symptom
A. Video error_Video error, video lag/stop
Content
TUNER input signal strength checking method
Established
2010. 12 .14
date
Revised
date
A6
<ALL MODELS>
MENU - Set up support - signal test

- select channel
When the signal is strong, use the

attenuator (-10dB, -15dB, -20dB etc.)

A6

LCD TV
Error
symptom
Content
LCD-TV Version checking method
<ALL MODELS>
Established
2010. 12 .14
date
Revised
date
A7
1. Checking method for remote controller for adjustment
Version
Press the IN-START with the

remote controller for adjustment
A7

LCD TV
Error
symptom
A. Video error _Vertical/Horizontal bar,

residual image, light spot
Content
LCD TV connection diagram (1)
Established
2010. 12 .14
date
Revised
date
A8
**LW95**, **LW77**, **LV55**, **LW65**, **LW57**
As the part connecting to the external input, check

the screen condition by signal
A8

LCD TV
Error
symptom
Content
TUNER checking part
Established
2010. 12 .14
date
Revised
date
A9
<ALL MODELS>
Checking method:
1. Check the signal strength or check whether the screen is normal when the external device is connected.
2. After measuring each voltage from power supply, finally replace the MAIN BOARD.

A9

LCD TV
Error
symptom
Content
Check Link Cable (LVDS) reconnection condition
Established
2010. 12 .14
date
Revised
date
A10
<ALL MODELS>
Check the contact condition of the Link Cable, especially dust or mis insertion.
A10

LCD TV
Error
symptom
Content

Check Link Cable reconnection condition
Established
2010. 12 .14
date
Revised
date
A11
<ALL MODELS>
Check the contact condition of the Link Cable, especially dust or mis insertion.
A11

LCD TV
Error
symptom
Content
Established
2010. 12 .14
date
Revised
date
A12
You can view 6 types of patterns using the ADJ Key

Checking item : 1. Defective pixel 2. Residual image 3. MODULE error (ADD-BAR,SCAN BAR..)
4.Video error (Classification of MODULE or Main-B/D!)
A12
Appendix : Exchange T-Con Board (1)
Solder defect, CNT Broken
T-Con
T-Con
Defect,
Defect,
CNT
CNT
Broken
Broken
Solder
defect,CNT
CNTBroken
Broken
T-Con
Defect,
Abnormal Power Section
Solder defect, Short/Crack


A - 1/5

Appendix : Exchange T-Con Board (2)
GRADATION
Fuse Open, Abnormal power section
Abnormal Display
Noise
GRADATION
A - 2/5
Appendix : Exchange PSU(LED driver)
No Light
Dim Light
Dim Light
Dim Light
No picture/Sound Ok
A - 3/5
Appendix : Exchange the Module (1)
Panel Mura, Light leakage
Crosstalk
Panel Mura, Light leakage
Press damage
Press damage
Crosstalk
Un-repairable Cases
In this case please exchange the module.
Press damage
A - 4/5
Appendix : Exchange the Module (2)
Vertical Block
Source TAB IC Defect
Horizontal Block
Gate TAB IC Defect
Vertical Line
Horizontal
Gate
TAB ICBlock
Defect
Gate TAB IC Defect
Vertical Block
Horizontal line
Gate TAB IC Defect
Gate TAB IC Defect
Un-repairable Cases
In this case please exchange the module.
Horizontal Block
Gate TAB IC Defect
Gate TAB IC Defect
A - 5/5

LCD TV
Error
symptom
B. Power error _No power
Content
Check front display LED
Established
2010. 12 .14
date
Revised
date
A17
Front LED control :

Menu Option Power Indicator
Standby light ON
ST-BY condition: Red

Power ON condition: white

A17

LCD TV
Error
symptom
Content
Established
2010. 12 .14
date
Revised
date

Check power input voltage and ST-BY 5V
A18
For 10 models, there is no voltage out for st-by purpose.

When st-by, only 3.5V is normally on.
ALEF LED
Check the DC 20V/24V, 12V, 3.5V.

Edge LED
Power on
20V (24V)
20V (24V)
20V (24V)
GND
GND
GND
GND
3.5V
10
3.5V
11
3.5V
12
3.5V
13
GND
14
GND
15
GND
16
GND
17
12V
18
Inverter On/off
19
12V
20
Lamp : A-Dim
LED : N.C
21
12V
22
PWM Dim #1
24
Error-out
23

N.C
Lamp SCANNING Model
: PWM Dim #2
A18

LCD TV
Error
symptom
Content
Established
2010. 12 .14
date
Revised
date

Checking method when power is ON
ALEF LED
A19
Check power on pin is high

Edge LED
Power on
20V (24V)
20V (24V)
20V (24V)
GND
GND
GND
GND
3.5V
10
3.5V
11
3.5V
12
3.5V
13
GND
14
GND
15
GND
16
GND
17
12V
18
Inverter On/off
19
12V
20
Lamp : A-Dim
LED : N.C
21
12V
22
PWM Dim #1
24
Error-out
23

N.C
Lamp SCANNING Model
: PWM Dim #2
A19

LCD TV
Error
symptom
B. Power error _Off when on, off whiling viewing Established 2010. 12 .14
date
Content
POWER OFF MODE checking method
Revised
date
A22
<ALL MODELS>
Entry method
1. Press the IN-START button of the remote
controller for adjustment
2. Check the entry into adjustment item 3
A22

LCD TV
Error
symptom
Content
Checking method in menu when there is no audio
Established
2010. 12 .14
date
Revised
date
A24
<ALL MODELS>
Checking method
1. Press the MENU button on the remote controller
2. Select the AUDIO function of the Menu
3. Select TV Speaker from Off to On

A24

LCD TV
Error
symptom
Content
Voltage and speaker checking method

when there is no audio
<ALL MODELS>
Established
date
Revised
date
2010. 12 .14
A25

Power on
20V (24V)
20V (24V)
20V (24V)
GND
GND
GND
GND
3.5V
10
3.5V
11
3.5V
12
3.5V
13
GND
14
GND
15
GND
16
GND
17
12V
18
Inverter On/off
19
12V
20
Lamp : A-Dim
LED : N.C
21
12V
22
PWM Dim #1
24
Error-out
23
N.C
Lamp SCANNING
Model
: PWM Dim #2
Checking order when there is no audio

Check the contact condition of or 24V connector of Main Board
Measure the 24V input voltage supplied from Power Board
(If there is no input voltage, remove and check the connector)
Connect the tester RX1 to the speaker terminal and if you hear the Chik Chik sound when you touch the
GND and output terminal, the speaker is normal.
A25

Error
D. Function error_ No response in remote controller,
symptom
key error
LCD TV
Content
Remote controller operation checking method
Established
2010. 12 .14
date
Revised
date
A27
<ALL MODELS>
1
2
3
4
5
6
7
8
9
P8200
SCL
SDA
GND
KEY1
KEY2
St 3.5V
GND
LED_B/logo_PWM
IR
10
GND
11
3.3V_Normal
12
LED_R/BUZZ
13
GND
14
ST_SCL
15
ST_SDA
Checking order
1, 2. Check IR cable condition between IR & Main board.
3.
Check the st-by 3.3V on the terminal 6.
4. When checking the Pre-Amp when the power is in ON condition, it is normal when the
Analog Tester needle moves slowly, and defective when it does not move at all.
A27

LCD TV
Error
symptom
D. VCOM Adjustment
Content
Sequence of the Vcom adjustment
Established
2010. 12 .14
date
Revised
date
A28
1. Case
LCD module change
T-Con board change
2. Equipment
Service Remote controller
3. Adjust sequence
Press the adj key
select V-COM
As pushing the right or the left button on the remote controller, And find the V-COM value Which is no or
minimized the Flicker.
(If there is no flicker at default value, Press the exit key and finish the VCOM adjustment.)
Push the OK key to store the value. Then the message Saving OK is pop.
Press the exit key to finish V-COM adjustment.

A28

LG 55LW9500 Ch. LB12D

Uploaded by

Copyright:

Available Formats

LG 55LW9500 Ch. LB12D

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LG 55LW9500 Ch. LB12D

Uploaded by

Copyright:

Available Formats

What are the main sections covered in the manual?

What are the main sections covered in the manual?

What safety precautions should be taken when servicing the TV?

What safety precautions should be taken when servicing the TV?

Internal Use Only

P/NO : MFL67007005 (1104-REV00)

Copyright 2011 LG Electronics. Inc. All rights reserved.

LGE Internal Use Only

Leakage Current Hot Check (See below Figure)

An isolation Transformer should always be used during the

Do not use a line Isolation Transformer during this check.

Leakage Current Hot Check circuit

Before returning the receiver to the customer,

Leakage Current Cold Check(Antenna Cold Check)

Copyright 2011 LG Electronics. Inc. All rights reserved.

Good Earth Ground

When 25A is impressed between Earth and 2nd Ground

LGE Internal Use Only

This specification is applied to the LCD TV used LB12D

1) Performance: LGE TV test method followed

2. Requirement for Test

4. Model General Specification

ASIA, Oceania, Africa,

DTV & Analog

Middle East(PAL/DVB Market)

* DTV Region : Australia/New Zealand(AU), Singapore(SG), Indonesia(ID),

* Australia/India : only PAL

Malaysia(MY), Vietnam(VN), South Africa(ZA), Iran(IR)

Analog : Upper Heterodyne

Digital : COFDM, QAM

- Modulation : Code Rate

: 1/2, 2/3, 3/4, 5/6, 7/8

16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8

Video Input RCA (2EA)

PAL, SECAM, NTSC

Head phone out

Antena, AV1, AV3, Component1,

4 System : PAL, SECAM, NTSC, PAL60

Component2, RGB, HDMI1, HDMI2,

Component Input (2EA)

RGB Input (1EA)

Rear 1EA, Gender 1EA

HDMI Input (4EA)

PC(HDMI version 1.3) Support HDCP

Audio Input (5EA)

SDPIF out (1EA)

EMF, DivX HD, For SVC(download)

Copyright 2011 LG Electronics. Inc. All rights reserved.

JPEG, MP3, DivX HD Plus

LGE Internal Use Only

5. Component Video Input (Y, CB/PB, CR/PR)

SDTV,DVD 625 Line

Input 848*480 60 Hz, 852*480 60 Hz

For only DOS mode

-> 640*480 60 Hz Display

Copyright 2011 LG Electronics. Inc. All rights reserved.

LGE Internal Use Only

9. 3D Mode - HDMI & USB

3D input proposed mode

Side by Side(half), Top and bottom

Input 848480 60 Hz, 852480 60 Hz