Plastic Road Report

TRANSPORT ENGINEERING
REPORT
ON
Plastic road
SUBMITTED BY,
VINAYAKA M N
1RV10CV403,
Harish v
1rv10cv401.
INTRODUCTION
Plastic use in road construction is not new. Recent studies in this direction have shown
some hope in terms of using plastic-waste in road construction i.e., Plastic roads. Plastic roads
mainly use plastic carry-bags, disposable cups and PET bottles that are collected from garbage
dumps as an important ingredient of the construction material. When mixed with hot bitumen,
plastics melt to form an oily coat over the aggregate and the mixture is laid on the road surface
like a normal tar road.
WHAT IS PLASTIC??
A plastic material is any of a wide range of synthetic or semi-synthetic organic amorphous solids
used in the manufacture of industrial products. Plastics are typically polymers of high molecular mass and
may contain other substances to improve performance and/or reduce costs. Monomers of plastic are either
natural or synthetic organic compounds.
BASIC PROCESSES:
Segregation.
Cleaning process.
Shredding process.
Collection process.
1. SEGRAGATION:
Plastic waste collected from various sources must be separated from other waste. Maximum
thickness of 60 microns.
2. CLEANING PROCESS:
Plastic waste gets cleaned and dried.

3. SHREDDING PROCESS:
It will be shredded or cut into small piece. The different types of plastic wastes are mixed
together
4. COLLECTION PROCESS:
It the plastic waste retaining in 2.36 mm is collected.
THE PLASTIC ROAD FOR SHORT TERM ACCESS:

The plastic road spreads wheel loads over an increased sub grade area, reducing rutting
and disturbance to soils and vegetation (see figure 2). This helps reduce water concentrations,
channeling, erosion, and the potential for damage to fish and wildlife habitat. A geotextile
underlayment (see figure 3) to the plastic road further increases environmental sensitivity by
separating the crossing from soil and allows water to filter through. Geotextile helps spread load,
may increase soil bearing capacity, and facilitates removal of the crossing after use. Removal is
quick and easy compared to that of conventional techniques for crossing soft spots and can aid in
closure and obliteration of the temporary road.
The plastic road is lightweight, portable, reusable, and inexpensive when amortized over
system life. Its length is tailored to site conditions in 10 foot (3 meter) increments. Plastic road
panels and required accessories for 40 linear feet (12 linear meters) of crossing may be
transported in a 3/4 ton pickup and assembled on a typical site by a two-person crew (see figure
4) in approximately 1 hour. This length of plastic road may be moved from site to site by
chaining-to and towing with a pickup truck or logging equipment. Worn or broken PVC pipe
members are easily replaced, facilitating maintenance and reuse of the system. Materials cost
including geotextile and transition mats (see figure 1) for this length of plastic road is
approximately $2000. Adding labor to fabricate increases the cost to approximately $2500.
Materials are readily available through major hardware distributors.
USE OF THE PLASTIC ROAD:

Vehicles negotiating the plastic road should travel at a constant 5 mph (8 kph); sudden
acceleration or deceleration may cause loss of traction, especially if the plastic is wet. The
system has successfully supported 18 wheels on highway (80,000 lbs GVW, or 36,400 kg) log
trucks (and other forest traffic and logging equipment) on straight alignments with grades up to 4
percent with no cross-slope. Steeper grades or the existence of cross-slope or horizontal
curvature may also result in loss of traction. Traction loss may occur between tires and the PVC,
or slippage may occur between the PVC and the soil or geotextile, causing it to work out of the
soil ramp if so installed (see figure 6). In these latter cases a wave may form in the crossing
system which can lead to failure if the system folds over on itself.
PLASTIC ROAD FIELD TESTS:

A PVC pipe mat used and removed at scores of sites on the Osceola Ranger District in
Florida remains serviceable after several hundred log truck passes and other heavy and light
vehicle traffic. A prototype plastic road installation tested by San Dimas Technology and
Development Center has supported over 400 loaded 18-wheel log truck passes at 2 sites. Testing
included several relatively high-speed passes (in excess of 10 mph, or 16 km/h), the negotiation of
several passes with driver and trailer tires only partially on the plastic road, and hard breaking.
Several passes were made with the plastic road located on a dry, hard, rocky sub grade, which
resulted in point-loading and breakage of several 4-inch pipes.
MATERIALS AND TOOLS REQUIRED FOR THE PLASTIC ROAD:

Plastic road fabrication requires the following parts
4-inch PVC Schedule 40, four foot lengths
3-inch PVC Schedule 40, four and three foot lengths
2-inch PVC Schedule 40, four foot lengths
1-inch PVC Schedule 80, ten foot lengths
1-inch PVC Schedule 80, eight inch lengths
3/8-inch diameter quick pins
3/8-inch cable
Cable clips for 3/8-inch cable
3/8-inch washers
To fabricate the plastic road you will need the following tools
Drill press
13/32-inch drill bit
1 3/8-inch drill bit
Power saw (abrasive, table, or radial arm)
Hammer
Pry-bar to fit 13/32-inch hole
Sander
ADVANTAGES:
Use higher percentage of plastic waste. Reduce the need of bitumen by around 10%.
Increase the strength and performance of the road.
Reduce the cost to around Rs. 5000/Km. of single lane road.
Generate jobs for rag pickers.
Develop a technology, which is eco-friendly.
100% improvement in fatigue life of roads.
Reduced penetration and ductility, a higher softening point, less rutting and cold
cracking.
DISADVANTAGES:
Cleaning process
Toxics present in the co-mingled plastic waste would start leaching .
During the road laying process
In the presence of chlorine will definitely release noxious HCL gas .
3.After the road laying
It is opined that the first rain will trigger leaching. As the plastics will merely
form a sticky layer, (mechanical abrasion). The components of the road, once it has been
laid, are not inert.
CONCLUSIONS:
The plastic road is available to aid short term access for vehicles and equipment into the
forest.
This system is lightweight, portable, reusable, inexpensive, & constructed of readily

available materials.
The plastic road reduces rut depth and has provided satisfactory service over sensitive
sites and soils of low bearing capacity.
Testing usage outside these constraints and further development effort to optimize
performance is warranted.
REFERENCE:
www.google.com
www.yahoo.com

Plastic Road Report

Uploaded by

Copyright:

Available Formats

Plastic Road Report

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Plastic Road Report

Uploaded by

Copyright:

Available Formats

What are the basic processes involved in plastic road construction?

What are some advantages of using plastic roads?

TRANSPORT ENGINEERING

Plastic waste gets cleaned and dried.

It the plastic waste retaining in 2.36 mm is collected.

THE PLASTIC ROAD FOR SHORT TERM ACCESS:

USE OF THE PLASTIC ROAD:

PLASTIC ROAD FIELD TESTS:

MATERIALS AND TOOLS REQUIRED FOR THE PLASTIC ROAD:

Increase the strength and performance of the road.

Reduce the cost to around Rs. 5000/Km. of single lane road.

Generate jobs for rag pickers.

Develop a technology, which is eco-friendly.

100% improvement in fatigue life of roads.

This system is lightweight, portable, reusable, inexpensive, & constructed of readily

You might also like