MS Maneurop Refigeration Compressors Spec Sheets

MAKING MODERN LIVING POSSIBLE
Maneurop reciprocating compressors

MT/MTZ 50 - 60 Hz - R22 - R407C - R134a - R404A / R507A
REFRIGERATION &
AIR CONDITIONING DIVISION
Selection &
Application guidelines
Contents
MANEUROP RECIPROCATING COMPRESSORS .................................................................................................................................................................................. p 3

COMPRESSOR MODEL DESIGNATION .................................................................................................................................................................................................................. p 4
Code numbers ................................................................................................................................................................................................................................................................................... p 4
Compressor reference .............................................................................................................................................................................................................................................................. p 4
Versions ............................................................................................................................................................................................................................................................................................................... p 4
SPECIFICATIONS ................................................................................................................................................................................................................................................................................................ p 5
Technical specications ........................................................................................................................................................................................................................................................ p 5
Approvals & certicates ......................................................................................................................................................................................................................................................... p 5
Nominal performance for R404A and R22 ......................................................................................................................................................................................... p 6
Nominal performance for R407C and R134a .................................................................................................................................................................................. p 7
OPERATING ENVELOPES ..................................................................................................................................................................................................................................................................... p 8
OUTLINE DRAWINGS ............................................................................................................................................................................................................................................................................ p 10
1 cylinder ...................................................................................................................................................................................................................................................................................................... p 10
2 cylinders .................................................................................................................................................................................................................................................................................................. p 11
4 cylinders .................................................................................................................................................................................................................................................................................................. p 12
ELECTRICAL CONNECTIONS AND WIRING ................................................................................................................................................................................................... p 13
Single phase electrical characteristics ................................................................................................................................................................................................... p 13
Nominal capacitor values and relays ........................................................................................................................................................................................................ p 13
Trickle circuit .......................................................................................................................................................................................................................................................................................... p 13
PSC wiring ................................................................................................................................................................................................................................................................................................... p 13
CSR wiring ................................................................................................................................................................................................................................................................................................... p 13
Suggested wiring diagrams ...................................................................................................................................................................................................................................... p 14
Three phase electrical characteristics ..................................................................................................................................................................................................... p 15
Motor protection and wiring diagrams ............................................................................................................................................................................................... p 15
Soft starters .............................................................................................................................................................................................................................................................................................. p 16
Voltage application range ............................................................................................................................................................................................................................................ p 16
IP rating ........................................................................................................................................................................................................................................................................................................... p 16
REFRIGERANTS AND LUBRICANTS .............................................................................................................................................................................................................................. p 17
General information ..................................................................................................................................................................................................................................................................p 17
SYSTEM DESIGN RECOMMENDATIONS .............................................................................................................................................................................................................. p 19
Piping design ........................................................................................................................................................................................................................................................................................ p 19
Operating limits .............................................................................................................................................................................................................................................................................. p 20
Operating voltage & cycle rate ............................................................................................................................................................................................................................ p 21
Liquid refrigerant control & charge limits ....................................................................................................................................................................................... p 21
SOUND AND VIBRATION MANAGEMENT ....................................................................................................................................................................................................... p 23
Sound ................................................................................................................................................................................................................................................................................................................. p 23
Vibration ....................................................................................................................................................................................................................................................................................................... p 23
INSTALLATION AND SERVICE ................................................................................................................................................................................................................................................ p 24
System cleanliness ..................................................................................................................................................................................................................................................................... p 24
Compressor handling, mounting and connection to the system ..................................................................................................... p 24
System pressure test .............................................................................................................................................................................................................................................................. p 25
Leak detection ................................................................................................................................................................................................................................................................................... p 25
Vacuum pull down - moisture removal ............................................................................................................................................................................................... p 25
Start-up ........................................................................................................................................................................................................................................................................................................... p 26
ORDERING INFORMATION AND PACKAGING ......................................................................................................................................................................................... p 27
Packaging ................................................................................................................................................................................................................................................................................................... p 27
Ordering information ........................................................................................................................................................................................................................................................... p 28
FRCC.PC.004.A4.02
Maneurop reciprocating compressors

Maneurop reciprocating compressors from
Danfoss Commercial Compressors are specially
designed for applications with a wide range of
operating conditions. All components are of high
quality and precision in order to assure a long
product life.
the HFC refrigerants R407C, R134a, R404A, and

R507A, using 160PZ polyester oil as lubricant.
Maneurop MT and MTZ series compressors are of

the hermetic reciprocating type and are designed
for medium and high evaporating temperature
applications.
MT and MTZ compressors have a large internal

free volume that protects against the risk of liquid hammering when liquid refrigerant enters the
compressor.
The compressor design allows for the motor to be

100% suction-gas cooled.
MT and MTZ compressors are fully suction-gas

cooled. This means that no additional compressor
cooling is required and allows the compressors to
be insulated with acoustic jackets, to obtain lower
sound levels, without the risk of compressor overheating.
The positive benets of internal motor protection, high eciency circular valve design and high
torque motors provide for a quality installation.
The MT series is designed for use with the traditional R22 refrigerant, using Danfoss mineral oil
160P as lubricant.
The MT series can also be applied with several R22
based refrigerant blends (substitute refrigerants),
using 160 ABM alkylbenzene as lubricant. The
MTZ series is specically designed for use with
FRCC.PC.004.A4.02
MTZ compressors can be used in new installations

and also to replace Maneurop MTE compressors
in existing installations.
MT and MTZ compressors are available in 22 different models with displacement ranging from
30 to 271 cm3/rev. Seven dierent motor voltage
ranges are available for single and three phase
power supplies at 50 and 60 Hz. Most compressors exist in two versions:
standard version
VE version (oil equalisation + oil sight glass).
Compressor model designation
Code numbers
(for ordering)
Compressor
type
Packaging type
I: single pack
M: industrial pack
(see ordering section)
Polyolester
oil
Oil equalisation port

and threaded sight glass
Motor power
(divide by 12 to convert to HP)
Motor voltage code

(see below)
Available code numbers are listed on pages 28-29
Compressor reference
(indicated on the
compressor nameplate)
Compressor
type
Option code
Oil equalisation port
and sight glass
Polyolester oil
Generation index
Motor power
(divide by 12 to convert to HP)
Motor voltage code

1: 208-230 V / 1 ph / 60 Hz
3: 200-230 V / 3 ph / 60 Hz
4: 400 V / 3 ph / 50 Hz
460 V / 3 ph / 60 Hz
5: 230 V / 1 ph / 50 Hz
6: 230 V / 3 ph / 50 Hz
7: 500 V / 3 ph / 50 Hz
575 V / 3 ph / 60 Hz
9: 380 V / 3 ph / 60 Hz
Displacement code
(see page 5)
Versions
S version
Models
Oil sight glass
VE version
Oil equalisation
connection
Oil sight glass
Oil equalisation
connection
MT/MTZ018-040 (1 cyl.)
threaded
3/8are
MT/MTZ044-081 (2 cyl.)
threaded
3/8are
MT/MTZ100-160 (4 cyl.)
welded
threaded
3/8are
FRCC.PC.004.A4.02
Specications
Technical specications
Compressor
model
Displacement
Cyl.
number
Oil
charge
dm3
Net
weight
kg
0.95
21
MT/MTZ018
JA
30.23
m3/h at
2900 rpm
5.26
MT/MTZ022
JC
38.12
6.63
0.95
21
Code
cm3/rev
MT/MTZ028
JE
48.06
8.36
0.95
23
MT/MTZ032
JF
53.86
9.37
0.95
24
MT/MTZ036
JG
60.47
10.52
0.95
25
MT/MTZ040
JH
67.89
11.81
0.95
26
MT/MTZ044
HJ
76.22
13.26
1.8
35
MT/MTZ045
HJ
76.22
13.26
1.8
37
MT/MTZ050
HK
85.64
14.90
1.8
35
MT/MTZ051
HK
85.64
14.90
1.8
37
MT/MTZ056
HL
96.13
16.73
1.8
37
MT/MTZ057
HL
96.13
16.73
1.8
39
MT/MTZ064
HM
107.71
18.74
1.8
37
MT/MTZ065
HM
107.71
18.74
1.8
39
MT/MTZ072
HN
120.94
21.04
1.8
40
MT/MTZ073
HN
120.94
21.04
1.8
41
MT/MTZ080
HP
135.78
23.63
1.8
40
MT/MTZ081
HP
135.78
23.63
1.8
41
MT/MTZ100
HS
171.26
29.80
3.9
60
MT/MTZ125
HU
215.44
37.49
3.9
64
MT/MTZ144
HV
241.87
42.09
3.9
67
MT/MTZ160
HW
271.55
47.25
3.9
69
Approvals and certicates
Pressure equipment
directive 97/23/EC
Low voltage directive

73/23/EC, 93/68/EC
Available in MT and MTZ
Available in MTZ only
Maneurop MT/MTZ compressors comply with

the following approvals and certicates.
Certicates are listed on the product datasheets:

http://www.danfoss.com/odsg
CE 0062 or CE 0038
(European Directive)
All models
UL
(Underwriters Laboratories)
All 60 Hz models
CCC
(China Compulsory Product Certication)
Depending on the model and motor voltage code.
Gost
certicate (for Russia)
Depending on the model and motor voltage code.
Products
Refrigerating uids
Category PED
Evaluation module
Service temperature - Ts
MT - Service pressure - Ps
MTZ - Service pressure - Ps
MT/ MTZ 18 to 40
Group 2
I
no scope
50c < Ts > -35c
18,4 bar(g)
22,6 bar(g)
MT/ MTZ 44 to 160

Group 2
II
D1
50c < Ts > -35c
18,4 bar(g)
22,6 bar(g)
Products
MT/ MTZ 18 to 40
MT/ MTZ 44 to 160
PED005C
PED005C
Manufacturer's declaration of incorporation

ref. EC Machines Directives 98/392/CE
Internal free volume
Products
1 cyl. with height = 333 mm (see page 10)
FRCC.PC.004.A4.02
Available motor voltage codes
Volume (litre)
7.2
7.7
2 cyl.
16.5
4 cyl . with height = 519 mm (see page 12)
30.7
32
Specications
Nominal performance data for R404A and R22
R404A
Compressor
model
MTZ018-4*
MTZ022-4*
MTZ028-4*
MTZ032-4*
MTZ036-4*
MTZ040-4*
MTZ044-4
MTZ045-4*
MTZ050-4
MTZ051-4*
MTZ056-4
MTZ057-4*
MTZ064-4
MTZ065-4*
MTZ072-4
MTZ073-4*
MTZ080-4
MTZ081-4*
MTZ100-4*
MTZ125-4*
MTZ144-4*
MTZ160-4*
Refrigeration
50 Hz, EN12900 ratings
50 Hz, ARI ratings
60 Hz, ARI ratings
To = -10 C, Tc = 45C, SC = 0 K, SH = 10 K
To = -6.7 C, Tc = 48.9 C, SC = 0 K, SH = 11.1 K
To = -6.7 C, Tc = 48.9 C, SC = 0 K, SH = 11.1 K
Cooling
capacity
W
Power
input
kW
Current
input
A
C.O.P.
W/W
Cooling
capacity
W
Power
input
kW
Current
input
A
1 900
2 620
3 430
3 980
4 670
5 330
1.21
1.48
1.96
2.16
2.58
2.95
2.73
3.06
4.04
4.25
4.95
5.87
1.58
1.77
1.75
1.84
1.81
1.81
2 070
2 830
3 690
4 260
4 990
5 680
1.31
1.62
2.14
2.37
2.83
3.24
2.86
3.24
4.30
4.56
5.33
6.29
5.40
5.96
5.88
6.15
6.02
5.97
5 150
5 370
6 150
6 260
7 000
6 710
8 130
7 980
9 150
8 920
10 520
10 470
3.16
2.77
3.61
3.22
4.00
3.51
4.54
4.20
4.99
4.69
5.84
5.61
6.37
5.35
6.53
5.95
7.07
6.83
8.30
7.82
8.64
8.95
10.12
10.20
1.63
1.93
1.70
1.94
1.75
1.91
1.79
1.90
1.84
1.90
1.80
1.87
5 530
5 780
6 580
6 700
7 500
7 250
8 700
8 590
9 760
9 570
11 200
11 180
3.43
3.02
3.92
3.50
4.38
3.85
4.96
4.60
5.45
5.11
6.38
6.14
6.66
5.67
6.92
6.33
7.57
7.25
8.84
8.35
9.28
9.50
10.87
10.94
12 280
15 710
18 490
20 310
6.76
8.44
9.78
11.08
12.21
13.79
16.29
18.26
1.82
1.86
1.89
1.83
13 170
16 800
19 690
21 660
7.35
9.21
10.65
12.09
12.94
14.86
17.47
19.64
* 50 Hz, EN12900 data for indicated models are Asercom certied
R22
Compressor
model
MT018-4
MT022-4
MT028-4
MT032-4
MT036-4
MT040-4
MT044-4
MT045-4
MT050-4
MT051-4
MT056-4
MT057-4
MT064-4
MT065-4
MT072-4
MT073-4
MT080-4
MT081-4
MT100-4
MT125-4
MT144-4
MT160-4
Power
input
kW
Current
input
A
E.E.R.
Btu.h/W
2 630
3 600
4 680
5 110
5 900
6 730
1.76
2.05
2.68
2.98
3.33
3.76
2.86
3.27
4.23
4.56
5.09
5.88
5.09
6.00
5.95
5.85
6.04
6.11
5.51
6.53
5.73
6.54
5.85
6.43
5.99
6.37
6.11
6.39
5.99
6.22
7 100
7 110
8 290
8 360
9 310
9 490
10 580
10 540
11 850
11 960
13 400
13 600
4.18
3.85
4.82
4.42
5.44
4.98
6.11
5.67
6.91
6.53
8.03
7.81
6.58
5.85
7.04
6.53
7.80
7.52
8.98
8.31
9.76
9.73
11.35
11.35
5.79
6.30
5.87
6.46
5.84
6.50
5.91
6.35
5.85
6.25
5.70
5.94
6.11
6.22
6.31
6.11
15 480
19 970
23 530
25 570
8.72
11.37
12.99
14.73
12.79
15.41
17.93
20.17
6.06
6.00
6.18
5.92
R404A data are also valid for refrigerant R507A
Refrigeration
Air Conditioning
50 Hz, ARI ratings
60 Hz, ARI ratings
To = -10 C, Tc = 45 C, SC = 0 K, SH = 10 K
To = +7.2C, Tc = 54.4 C, SC = 8.3 K, SH = 11.1 K
To = +7.2C, Tc = 54.4 C, SC = 8.3 K, SH = 11.1 K
Cooling
capacity
W
Power
input
kW
Current
input
A
C.O.P.
W/W
Cooling
capacity
W
Power
input
kW
Current
input
A
1 690
2 490
3 730
3 950
4 810
5 220
1.00
1.29
1.81
2.11
2.35
2.67
2.27
2.55
3.59
3.73
4.30
4.86
1.69
1.94
2.06
1.87
2.04
1.95
3 880
5 360
7 380
8 060
9 270
10 480
1.45
1.89
2.55
2.98
3.37
3.86
2.73
3.31
4.56
4.97
5.77
6.47
9.16
9.69
9.87
9.22
9.38
9.27
5 300
4 860
5 810
5 870
6 830
6 440
7 640
7 750
8 520
8 710
9 720
10 360
2.72
2.46
2.95
2.94
3.44
3.18
3.89
3.64
4.29
4.19
4.84
4.89
6.03
5.02
5.22
5.53
6.21
6.39
7.06
7.03
7.58
8.48
8.24
9.52
1.95
1.98
1.97
2.00
1.99
2.03
1.96
2.13
1.99
2.08
2.01
2.12
11 040
10 520
12 320
12 230
13 770
13 750
15 820
15 730
17 120
18 190
19 530
20 730
3.89
3.53
4.32
4.19
5.04
4.58
5.66
5.27
6.31
6.12
7.13
7.08
7.37
6.37
8.46
7.20
10.27
8.19
9.54
9.16
10.54
10.98
11.58
12.48
11 330
15 260
17 270
19 190
5.79
7.55
8.47
9.49
11.82
12.28
17.06
16.81
1.96
2.02
2.04
2.02
23 400
30 430
34 340
38 270
7.98
10.66
11.95
13.40
14.59
17.37
22.75
22.16
To: Evaporating temperature at dew point (saturated suction temperature)

Tc: Condensing temperature at dew point (saturated discharge temperature)
SC: Subcooling,
SH: Superheat
Cooling
E.E.R.
capacity
Btu.h/W
W
Cooling
E.E.R.
capacity
Btu.h/W
W
Power
input
kW
Current
input
A
E.E.R.
Btu.h/W
4 660
6 440
8 850
9 680
11 130
12 570
1.74
2.27
3.06
3.58
4.05
4.63
2.73
3.31
4.56
4.97
5.77
6.47
9.16
9.69
9.87
9.22
9.38
9.27
9.69
10.17
9.74
9.97
9.32
10.24
9.53
10.18
9.26
10.15
9.36
9.99
13 240
12 890
14 790
14 690
16 530
16 520
18 980
18 850
20 550
21 840
23 440
24 880
4.66
4.32
5.18
5.04
6.05
5.58
6.80
6.32
7.57
7.33
8.55
8.50
7.37
6.42
8.46
7.26
10.27
8.23
9.54
9.33
10.54
10.77
11.58
12.34
9.69
10.18
9.74
9.95
9.32
10.10
9.53
10.18
9.26
10.16
9.36
10.00
10.00
9.74
9.80
9.75
28 080
36 510
41 210
45 930
9.58
12.80
14.35
16.08
14.59
17.37
22.75
22.16
10.00
9.74
9.80
9.75
ARI capacity and power input data are +/- 5%

Asercom: Association of European Refrigeration Compressor and
Controls Manufacturers
ARI: Air Conditioning and Refrigeration Institute
FRCC.PC.004.A4.02
Specications
Nominal performance data for R407C and R134a

R407C
Compressor
model
MTZ018-4*
MTZ022-4*
MTZ028-4*
MTZ032-4*
MTZ036-4*
MTZ040-4*
MTZ044-4
MTZ045-4*
MTZ050-4
MTZ051-4*
MTZ056-4
MTZ057-4*
MTZ064-4
MTZ065-4*
MTZ072-4
MTZ073-4*
MTZ080-4
MTZ081-4*
MTZ100-4*
MTZ125-4*
MTZ144-4*
MTZ160-4*
Air Conditioning
50 Hz, ARI ratings
60 Hz, ARI ratings
To = +5 C, Tc = 50 C, SC = 0 K, SH = 10 K
To = +7.2 C, Tc = 54.4 C, SC = 8.3 K, SH = 11.1 K
To = +7.2 C, Tc = 54.4 C, SC = 8.3 K, SH = 11.1 K
Cooling
capacity
W
Power
input
kW
Current
input
A
C.O.P.
W/W
Cooling
capacity
W
Power
input
kW
Current
input
A
Cooling
E.E.R.
capacity
Btu.h/W
W
Power
input
kW
Current
input
A
E.E.R.
Btu.h/W
3 470
4 550
5 880
6 650
7 510
8 660
1.27
1.71
2.17
2.43
2.93
3.40
2.73
3.27
4.30
4.57
5.58
6.46
2.73
2.67
2.72
2.74
2.56
2.55
3 850
5 020
6 540
7 330
8 280
9 580
1.38
1.86
2.36
2.65
3.21
3.71
2.86
3.47
4.57
4.90
5.99
6.92
9.53
9.23
9.45
9.43
8.82
8.81
5 050
6 280
8 220
8 990
9 990
11 720
1.73
2.26
2.82
3.20
3.90
4.46
2.82
3.45
4.41
4.80
5.78
6.69
9.98
9.48
9.93
9.61
8.74
8.98
8 940
9 130
10 190
10 420
11 700
11 680
13 180
13 360
14 800
15 320
16 750
17 380
3.34
3.12
3.79
3.69
4.32
4.02
4.84
4.61
5.50
5.42
6.29
6.29
6.10
5.84
6.90
6.51
7.85
7.45
8.79
8.35
9.81
9.85
11.02
11.31
2.67
2.93
2.69
2.83
2.71
2.90
2.72
2.90
2.69
2.83
2.66
2.76
9 870
10 100
11 270
11 530
12 940
13 000
14 590
14 850
16 380
17 050
18 530
19 330
3.63
3.38
4.11
4.01
4.69
4.37
5.26
5.02
5.97
5.87
6.83
6.83
6.49
6.18
7.34
6.95
8.36
7.91
9.35
8.91
10.48
10.48
11.83
12.08
9.27
10.21
9.34
9.82
9.42
10.16
9.47
10.10
9.36
9.91
9.25
9.67
12 600
12 730
14 100
14 110
15 920
16 050
17 700
18 080
19 890
20 780
22 520
22 870
4.36
4.25
4.95
4.87
5.66
5.40
6.35
6.14
7.21
7.30
8.24
8.24
6.84
6.34
7.33
7.06
8.41
8.03
9.47
9.01
10.78
10.61
12.35
11.99
9.85
10.23
9.72
9.89
9.60
10.15
9.50
10.05
9.41
9.72
9.33
9.47
20 480
26 880
29 770
34 090
7.38
9.48
10.68
12.40
13.05
15.14
17.55
20.08
2.78
2.84
2.79
2.75
22 700
29 790
33 070
37 820
8.00
10.32
11.59
13.46
13.83
16.28
18.80
21.50
9.69
9.85
9.74
9.59
28 220
35 620
40 900
45 220
9.86
12.83
14.42
16.64
14.22
18.07
19.81
22.46
9.77
9.47
9.68
9.27
* 50 Hz, EN12900 data for indicated models are Asercom certied
R134a
Compressor
model
MTZ018-4
MTZ022-4
MTZ028-4
MTZ032-4
MTZ036-4
MTZ040-4
MTZ044-4
MTZ045-4
MTZ050-4
MTZ051-4
MTZ056-4
MTZ057-4
MTZ064-4
MTZ065-4
MTZ072-4
MTZ073-4
MTZ080-4
MTZ081-4
MTZ100-4
MTZ125-4
MTZ144-4
MTZ160-4
Air Conditioning
50 Hz, ARI ratings
60 Hz, ARI ratings
To = +5 C, Tc = 50 C, SC = 0 K, SH = 10 K
To = +7.2 C, Tc = 54.4 C, SC = 8.3 K, SH = 11.1 K
To = +7.2 C, Tc = 54.4 C, SC = 8.3 K, SH = 11.1 K
Cooling
capacity
W
Power
input
kW
Current
input
A
C.O.P.
W/W
Cooling
capacity
W
Power
input
kW
Current
input
A
2 310
3 000
3 730
4 390
5 340
5 700
0.92
1.11
1.41
1.74
1.97
2.15
2.12
2.42
3.18
3.80
3.88
4.58
2.51
2.70
2.65
2.52
2.71
2.66
2 550
3 350
4 210
4 950
6 000
6 400
0.99
1.20
1.53
1.87
2.13
2.33
2.19
2.51
3.30
3.94
4.09
4.89
8.81
9.56
9.40
9.03
9.60
9.36
6 120
6 090
7 170
7 110
8 040
7 680
9 160
8 960
10 540
10 230
12 080
11 750
2.36
2.06
2.68
2.44
2.99
2.62
3.36
3.02
3.74
3.50
4.31
4.02
5.51
4.56
5.33
5.02
5.61
5.93
6.66
6.53
6.83
7.66
8.03
8.44
2.60
2.96
2.67
2.91
2.69
2.93
2.73
2.96
2.82
2.92
2.80
2.92
6 870
6 850
8 070
8 010
9 070
8 720
10 350
10 160
11 850
11 650
13 580
13 320
2.52
2.22
2.88
2.63
3.21
2.84
3.62
3.26
4.01
3.78
4.64
4.35
5.65
4.73
5.50
5.20
5.83
6.17
6.96
6.81
7.20
7.99
8.45
8.83
13 770
16 980
21 030
23 080
4.89
5.84
7.27
7.98
9.84
10.24
13.11
13.90
2.81
2.91
2.89
2.89
15 530
19 070
23 620
25 860
5.28
6.29
7.83
8.57
10.24
10.80
13.78
14.67
To: Evaporating temperature at dew point (saturated suction temperature)

Tc: Condensing temperature at dew point (saturated discharge temperature)
SC: Subcooling,
SH: Superheat
FRCC.PC.004.A4.02
Cooling
E.E.R.
capacity
Btu.h/W
W
Power
input
kW
Current
input
A
E.E.R.
Btu.h/W
3 280
4 350
5 640
6 130
7 170
8 160
1.22
1.54
2.04
2.39
2.75
3.08
2.09
2.56
3.37
3.89
4.20
4.72
9.20
9.63
9.43
8.76
8.91
9.03
9.29
10.53
9.57
10.39
9.63
10.47
9.77
10.63
10.09
10.52
10.00
10.44
8 740
8 820
10 090
10 110
11 130
11 380
13 260
13 000
14 640
14 640
16 550
16 490
3.14
2.84
3.60
3.29
3.95
3.82
4.68
4.20
5.19
4.81
5.99
5.47
5.47
4.70
5.36
5.33
5.92
6.37
7.11
6.77
7.59
7.88
8.79
8.68
9.51
10.59
9.57
10.48
9.62
10.16
9.67
10.56
9.64
10.39
9.42
10.29
10.04
10.35
10.30
10.29
18 730
23 110
28 390
31 520
6.50
7.71
9.81
10.91
10.11
11.09
14.28
15.54
9.84
10.23
9.87
9.86
ARI capacity and power input data are +/- 5%

Asercom: Association of European Refrigeration Compressor and
Controls Manufacturers
ARI: Air Conditioning and Refrigeration Institute
Operating envelopes
MT - R22
MTZ - R407C at DEW point

Condensing temperature (C)
70
65
60
S.H. = 11.1 K
55
S.H. = 30 K
50
45
40
35
30
-30
-25
-20
-5
-10
0
Evaporating temperature (C)
-15
10
15
20
MTZ - R134a
Condensing temperature (C)
80
75
70
S.H. = 11.1 K
65
60
S.H. = 30 K
55
50
45
40
35
-20
-15
-10
-5
0
5
10
Evaporating temperature (C)
15
20
25
MTZ - R404A / R507A
FRCC.PC.004.A4.02
Operating envelopes
Zeotropic refrigerant
mixtures
Refrigerant mixtures can be either zeotropic or

azeotropic.
An azeotropic mixture (like R502 or R507A) behaves like a pure refrigerant. During a phase transition (from vapour to liquid or from liquid to vapour) thecomposition of vapour and liquid stays
the same.
In a zeotropic mixture (like R407C) on the other

hand the composition of vapour and liquid changes during the phase transition. When the eect of
this phase transition is very small, the mixture is
often called a near-azeotropic mixture. R404A is
such a near-azeotropic mixture.
The composition change causes phase shift and
temperature glide.
Phase shift
In system components where both vapour and

liquid phase are present (evaporator, condenser,
liquid receiver), the liquid phase and vapour
phase do not have the same composition. In
fact both phases form two dierent refrigerants.
Therefore zeotropic refrigerants need some spe-
cial attention. Zeotropic refrigerants must always

be charged in liquid phase. Flooded evaporators
and suction accumulators should not be applied
in systems with zeotropic refrigerants. This also
applies to near-azeotropic mixtures.
Temperature glide
During the evaporating process and the condensing process at constant pressure, the refrigerant
temperature will decrease in the condenser and
rise in the evaporator. Therefore when speaking
about evaporating and condensing temperatures, it is important to indicate whether this is a
dew point temperature or a mean point value. In
the gure below, the dotted lines are lines of constant temperature.
Points C and D are mean point values. These are

temperatures which correspond more or less with
the average temperature during the evaporating
and condensing process. For the same R407C cycle, mean point temperatures are typically about
2 to 3C lower than dew point temperatures. According to Asercom recommendations, Danfoss
Commercial Compressors uses dew point temperatures for selection tables and application envelopes etc.
They do not correspond to the lines of constant

pressure.
Points A and B are dew point values. These are
temperatures on the saturated vapour line.
To obtain exact capacity data at mean point temperatures, the mean point temperatures must be
converted to dew point temperatures with help
of refrigerant data tables from the refrigerant
manufacturer.
Dew temperature and Mean

temperature for R407C
FRCC.PC.004.A4.02
Outline drawings
1 cylinder
224
Suction rotolock
11/4
LP gauge
port 1/4
(schrader)
333 (1) (3)
356 (2)
263
oil equalisation
(VE models only)
Discharge rotolock
1
98
68
68
25
82
Mounting hole for PTC crankcase heater

118
109
33
35
Silent bloc
Threaded oil
sight glass
Suction: 142 (1) / 147 (2) (3)

Discharge: 142 (1) / 142 (2) (3)
Bolt HM8-40
39
68
15
23
141
123
31.75
17
159
17
(1) MT/MTZ 18-1/3/4/5/6, 22 & 28-3/4/5/6/7/9

(2) MT/MTZ 28-1, 32 & 36, 40-1/3/4/6
(3) MT/MTZ 22-1
Terminal box
Spade connectors
1/4" AMP-AWE
21 mm
Earth M4-12
Knock-out 21 mm
IP rating: 55 (with cable gland)

Rotolock connections size
Suction
Discharge
MT/MTZ 018 - 022 (3/4/5/6) 028 (3/4/5/6)
MT/MTZ022 (1) - 028 (1) 032 - 036 - 040
10
Pipe sizing
Suction
Discharge
Rotolock valve
Suction
Discharge
1/2
3/8
V06
V01
11/4
5/8
1/2
V09
V06
FRCC.PC.004.A4.02
Outline drawings
2 cylinders
288
Suction rotolock
1"3/4
Schrader 1/4"
413
Discharge rotolock
1"1/4
252
Oil equalisation
3/8"
265
Mounting hole for

PTC crankcase heater
117(1)
98(2)
74
68
Threaded oil sight glass
20
156
60
Suction 179
Discharge 176
98 (1) / 82(2)
Silent bloc
Bolt HM8-40
171
145
21
38
15
23
125
31.75
8
1) MT/MTZ 44-6, 5 0 - 56/64-1/6, 72-6, 80-3/6, 81-3
2) MT/MTZ 44-1/3/4/7/9, 45/51/57/ 65/73 -3/4, 50-3/4/5/7/9,
56-3/4/7/9, 64/72-3/4/9, 80-4/9,81-4
96
196 (1) / 188 (2)
Terminal box for model (1)
Terminal box for model (2)
Screw
10-32 UNF x 9.5
Spade connectors
1/4" AMP-AWE
Knock-out
25.5 mm
21 mm
Earth M4-12
Earth M4-12
Knock-out 21 mm
Knock-out 29 mm

Suction
Discharge
FRCC.PC.004.A4.02
Pipe sizing
Suction
Discharge
Rotolock valve
Suction
Discharge
MT/MTZ044 - 045 - 050 - 051 056 - 057 - 064 - 065 - 072 - 073
13/4
11/4
7/8
3/4
V07
V04
MT/MTZ080 - 081
13/4
11/4
11/8
3/4
V02
V04
11
Outline drawings
4 cylinders
352
210
Schrader 1/4 "
518 (1)
538 (2)
Suction rotolock
1"3/4
Discharge rotolock
1"1/4
117
Oil equalisation
3/8"
Threaded oil
sight glass
209
233
155
125
95
99
98
232
Mounting hole for
PTC crankcase heater
15
246
Silent bloc
15
205
155
15
1) MT/MTZ 144-160 3/4/6/7/9

2) MT/MTZ 100-125 3/4/6/7/9
246
Terminal box
Screw
10-32 UNF x 9.5
Knock-out
25.5 mm
Earth M4-12
Knock-out 29 mm

Suction
Discharge
MT/MTZ100 - 125 - 144 - 160
12
13/4
11/4
Pipe sizing
Suction
Discharge
11/8
3/4
Rotolock valve
Suction
Discharge
V02
V04
FRCC.PC.004.A4.02
Electrical connections and wiring

LRA - Locked Rotor
Current (A)
Single phase electrical

characteristics
Motor Code
MCC - Maximum Continuous

Current (A)
Winding
run
start
40
13
10
1.36
4.82
1.80
4.70
MT/MTZ022
49.3
41
17
15
1.25
2.49
1.78
4.74
MT/MTZ028
81
51
25
20
0.74
1.85
1.16
3.24
MT/MTZ032
84
70
26.5
20
0.64
2.85
0.90
4.30
MT/MTZ036
84
60
30
22
0.64
2.85
0.89
4.35
MT/MTZ040
99
34
0.53
2.00
MT/MTZ044
97
31
0.45
1.90
MT/MTZ050
114
92
36
29
0.37
1.79
0.52
2.65
MT/MTZ056
136
42.5
0.32
1.61
MT/MTZ064
143
46
0.32
2.10
PSC/CSR*
Models
50 Hz
60 Hz
Trickle circuit
start
51
CSR only
Run capacitors (1)

(A) F
PSC: Permanent Split Capacitor

CSR: Capacitor Start Run
(1) Run capacitors: 440 volts
(2) Start capacitors: 330 Volts
run
MT/MTZ018
Nominal capacitor values

and relays
Winding resistance ()
( 7 % at 20 C)
Start capacitors (2)
(C) F
(B) F
MT/MTZ018 JA-5
20
10
100
MT/MTZ022 JC-5
20
10
100
MT/MTZ028 JE-5
20
10
100
MT/MTZ032 JF-5
25
10
135
MT/MTZ036 JG-5
25
10
135
MT/MTZ050 HK-5
30
15
135
MT/MTZ018 JA-1
15
10
100
MT/MTZ022 JC-1
30
15
100
MT/MTZ028 JE-1
25
25
135
MT/MTZ032 JF-1
25
20
100
MT/MTZ036 JG-1
25
20
100
MT/MTZ040 JH-1
35
20
100
MT/MTZ044 HJ-1
30
15
135
MT/MTZ050 HK-1
30
15
135
MT/MTZ056 HL-1
35
20
200
MT/MTZ064 HM-1
30
25
235
The trickle circuit provides the facility of heating

the compressor crankcase by feeding a small current to the auxiliary winding and the run capacitor (See the drawings page 14.)
By using PSC or CSR starting systems, compressor models MT / MTZ 018 - 022 can be operated
Start relay
3ARR3J4A4
/RVA6AMKL
3ARR3J4A4
/RVA6AMKL
without crankcase heaters as the heater function

is provided by the trickle circuit.
For the larger single phase compressor models
MT / MTZ 028 - 064, the use of the PTC crankcase
heater is recommended.
PSC wiring
PSC wiring may be used for refrigerant circuits

with capillary tubes or expansion valves with
bleed ports. Pressure equalisation must be en-
sured before start-up because of the low starting

torque characteristics of this system.
CSR wiring
CSR wiring provides additional motor torque at

start-up, by the use of a start capacitor in combination with the run capacitor. This system can be
used for refrigerant circuits with capillary tubes or
expansion valves. The start capacitor is only connected during the starting operation, a potential
relay is used to disconnect it after the start sequence.
bimetallic protector, which senses the main and

start winding currents, and also the winding temperature. Once the protector has tripped, it may
take up to two to four hours to reset and restart
the compressor.
Check that power supply corresponds to
compressor characteristics (refer to compressor
nameplate).
The single phase compressor motors are internally protected by a temperature/current sensing
FRCC.PC.004.A4.02
13
Suggested wiring diagrams
Single phase - PSC wiring

with trickle circuit
230 V
IOL
A&C
C
S
R
220 k - 1 W
Motor protector
Run capacitors
Common
Start winding (auxiliary)
Run winding (main)
A F
Single phase - CSR wiring

with trickle circuit
C F
Thermostat
IOL
230 V
Start relay
5
IOL
A&C
B
C
S
R
220 k - 1 W
Motor protector
Run capacitors
Start capacitor
Common
Run winding (main)
IOL
2
A F
B F
C F
Thermostat
15 k - 1 W
Single phase - CSR wiring

without trickle circuit
230 V
Start Relay
C
IOL
Motor protector
A+C
Run capacitors
B
Start capacitor
C
Common
S
R
Run winding (main)
Capacitors A and C can be replaced by
a single capacitor of size A + C
Thermostat
IOL
CF
Run capacitor
AF
Run capacitor
BF
Start capacitor
14
15 k -1 w
FRCC.PC.004.A4.02
Three phase electrical

characteristics
LRA - Locked Rotor
Current (A)
MCC - Maximum
Continuous Current (A)
Winding resistance ()
( 7 % at 20 C)
Motor Code
MT/MTZ018
38
20
2.49
10.24
MT/MTZ022
38
16
30
22.5
11
8.5
2.49
10.24
3.38
6.58
MT/MTZ028
57
23
41
32
16
7.5
11.5
8.5
1.37
7.11
3.38
4.80
MT/MTZ032
60
25
44
22
35
18
13
5.5
1.27
6.15
1.27
8.90
4.20
MT/MTZ036
74
30
74
26
35
17
17
9.5
1.16
5.57
1.16
8.60
4.10
MT/MTZ040
98
38
74
22
10
18
0.95
4.56
0.95
MT/MTZ044
115
42
77
44
78
22
9.5
16
8.5
13
0.74
3.80
1.13
5.83
1.68
MT/MTZ045
115
48.5
17
9.5
0.69
3.22
MT/MTZ050
115
42
77
44
78
25
12
19
10
13.5
0.72
3.80
1.39
5.83
1.68
MT/MTZ051
120
48.5
22
11.5
0.69
3.60
MT/MTZ056
130
60
105
50
72
26
12
23
11
15
0.57
2.41
0.76
3.86
1.64
MT/MTZ057
130
64
24
12
0.55
2.39
MT/MTZ064
137
67
124
72
29
15
25
17.5
0.57
2.41
0.76
1.64
MT/MTZ065
135
64
28
14
0.55
2.39
MT/MTZ072
135
80
143
100
30
15.5
27
18.5
0.55
1.90
0.56
1.32
MT/MTZ073
155
80
32
17
0.48
1.90
MT/MTZ080
140
80
132
102
36
18
29
22.5
0.48
1.90
0.56
1.30
MT/MTZ081
140
80
36
19
0.48
1.90
MT/MTZ100
157
90
126
62
110
43
22
35
17
26
0.50
1.85
0.67
3.10
1.26
MT/MTZ 125
210
105
170
75
150
54
27
43
22
30
0.38
1.57
0.43
2.51
0.84
MT/MTZ 144
259
115
208
90
165
64
30
51
25
40
0.27
1.19
0.37
2.00
0.72
MT/MTZ 160
259
140
208
99
165
70
36
51
29
46
0.27
1.10
0.37
1.76
1.10
Motor protection and

suggested wiring diagrams
Suggested wiring diagram

with pump-down cycle and
safety lock-out relay
The 3-phase compressors are protected by an internal motor protector, connected to the neutral
point of the star connected stator windings, the
protector cuts out all 3-phases simultaneously.
Note: once the overload protector has tripped it

may take up to 3 hours to reset and restart the
compressor.
For all 3-phase compressors, a PTC crankcase
heater is required.
CONTROL CIRCUIT
L1
L3
L2
Q1
F1
F1
KM
KA
Control device ................................................ TH

Optional short cycle timer (3 min) ..... 180 s
Control relay .................................................... KA
Liquid Solenoid valve ............................... LLSV
Compressor contactor ................................ KM
Safety lock out relay ...................................... KS
Pump-down control & LP switch ............... LP
H.P. switch ........................................................ HP
Fused disconnect .......................................... Q1
Fuses ................................................................... F1
Compressor motor .......................................... M
Discharge gas thermostat ....................... DGT
KM
KA
KS
KA
A1
T1
T2
A3
KS
180 s
HP
T3
A2
TH
LP
KS
M
DGT
KM
FRCC.PC.004.A4.02
KA
LLSV
KS
15
Wiring diagram without
pump-down cycle
CONTROL CIRCUIT
L1
L3
L2
Q1
Control device ................................................ TH

Optional short cycle timer (3 min) ..... 180 s
Control relay .................................................... KA
Compressor contactor ................................ KM
Safety lock out relay ...................................... KS
High pressure switch .................................... HP
Low pressure switch ....................................... LP
Fused disconnect .......................................... Q1
Fuses ................................................................... F1
Compressor motor .......................................... M
Discharge gas thermostat ....................... DGT
F1
F1
KM
KA
KA
KS
KA
A1
T2
T1
A3
HP
180 s
A2
T3
LP
KS
TH
M
DGT
KM
Soft starters
KS
KA
Starting current of Maneurop 3-phase compressors can be reduced by using a soft starter. Two
dierent versions are available: CI-tronicTM soft
starters type MCI (recommended) and soft start
kits with statoric resistors type SCR. The starting
current can be reduced by up to 50% depending on the compressor model and the type of
soft starter. Also mechanical stresses that occur
at starting are reduced which increases the life of
the internal components.
For details of the CI-tronicTM MCI soft starters,

please refer to literature DKACT.PD.C50.
For details of the SCR soft start kits, please contact
Danfoss.
The number of starts should be limited to 6 per
hour. HP/LP pressure equalisation is required before starting.
Voltage application range

Motor Code
1
3
4
5
6
7
9
IP rating
Nominal voltage
Voltage application range
208-230 V / 1 ph / 60 Hz
187 - 253 V
200-230 V / 3 ph / 60 Hz
180 - 253 V
380-400 V / 3 ph / 50 Hz
340 - 440 V
460 V / 3 ph / 60 Hz
414 - 506 V
230 V / 1 ph / 50 Hz
207 - 253 V
230 V / 3 ph / 50 Hz
207 - 253 V
500 V / 3 ph / 50 Hz
450 - 550 V
575 V / 3 ph / 60 Hz
517 - 632 V
380 V / 3 ph / 60 Hz
342 - 418 V
The compressor terminal boxes IP rating according to CEI 529 are shown on the outline drawings
section.
The IP ratings are only valid when correctly sized

cable glands of the same IP rating are applied.
IP
1st numeral, level of protection against contact and foreign objects

5 complete protection against contact and against harmful dust deposits
2nd numeral, level of protection against water
4 protection against water splashing from any direction
5 protection against jets of water from any direction
16
FRCC.PC.004.A4.02
Refrigerants and lubricants
General information
When choosing a refrigerant, dierent aspects

must be taken into consideration:
Legislation (now and in the future)
Safety
Application envelope in relation to expected
running conditions
Compressor capacity and eciency
Compressor manufacturer recommendations
& guidelines
Refrigerant
Type
Lubricant
type
Compressor
type
Additional points could inuence the nal

choice:
Environmental considerations
Standardisation of refrigerants and lubricants
Refrigerant cost
Refrigerant availability
The table below gives an overview of the dierent
refrigerant - lubricant - compressor combinations
for Maneurop MT & MTZ compressors.
Danfoss lubricant
Application
R22
HCFC
Mineral
MT
White oil, 160P
Medium / High temperature
R407C
HFC
Polyolester
MTZ
Polyolester oil 160PZ
R134a
HFC
Polyolester
MTZ
R404A
HFC
Polyolester
MTZ
Medium temperature
R507A
HFC
Polyolester
MTZ
Medium temperature
Alkylbenzene
(ABM)
MT
Alkylbenzene oil 160 ABM

Note: Initial mineral oil charge has
to be replaced by 160 ABM oil.
Transitional
refrigerants,
R22 based
Hydrocarbons
Danfoss does not authorise the use of hydrocarbons in Maneurop MT/MTZ compressors
The Montreal protocol states that CFC refrigerants

such as R12 and R502 may no longer be applied in
new installations in the signatory members countries.
Therefore capacity and other data for these

refrigerants are not published in this document.
Maneurop MT compressors however are suitable
for use with these refrigerants and can still be
used as replacements in existing installations.
R22
R22 is an HCFC refrigerant and is still a wide use

today. It has a low ODP (Ozone Depletion Potential) and therefore it will be phased out in the future. Check local legislation. Always use mineral
white oil 160P.
The Maneurop MT compressor is dedicated for

R22 and is supplied with an initial mineral oil
charge.
R407C
Refrigerant R407C is an HFC refrigerant with similar thermodynamic properties to those of R22.
Always use the Maneurop MTZ compressors with

Danfoss 160PZ polyolester oil, which is supplied
with the MTZ compressor for R407C applications.
R407C has zero ozone depletion potential

(ODP=0). Many installers and OEMs consider
R407C to be the standard alternative for R22.
R407C is a zeotropic mixture and has a temperature glide of about 6 K. For more specic information about zeotropic refrigerants; refer to section
"zeotropic refrigerant mixtures". R407C must be
charged in the liquid phase.
FRCC.PC.004.A4.02
Maneurop MT compressors should never be

used with R407C, even when the mineral oil is replaced with polyolester oil.
17
Refrigerants and lubricants
R134a
Refrigerant R134a is an HFC refrigerant with thermodynamic properties comparable to those of

the CFC refrigerant R12. R134a has zero ozone
depletion potential (ODP = 0) and is commonly
accepted as the best R12 alternative. For applications with high evaporating and high condensing
temperatures, R134a is the ideal choice. R134a is a
pure refrigerant and has zero temperature glide.
For R134a applications always use the Maneurop

MTZ compressor with Danfoss 160PZ polyolester
oil which is supplied with the MTZ compressor.
Refrigerant R404A is an HFC refrigerant with thermodynamic properties comparable to those of

the CFC refrigerant R502. R404A has zero ozone
depletion potential (ODP = 0) and is commonly
accepted as one of the best R502 alternatives.
R404A is especially suitable for low evaporating
temperature applications but it can also be applied to medium evaporating temperature applications. R404A is a mixture and has a very small
temperature glide, and therefore must be charged
in its liquid phase, but for most other aspects this
small glide can be neglected. Because of the small
glide, R404A is often called a near-azeotropic mix-
ture. For more information refer to section zeotropic refrigerant mixtures. For low evaporating
temperature applications down to -45C, Maneurop NTZ compressors should be used. Refer to
the NTZ selection and application guidelines. For
medium temperature R404A applications, always
use the Maneurop MTZ compressor with 160PZ
polyolester oil which is supplied with the MTZ
compressor.
Refrigerant R507A is an HFC refrigerant with thermodynamic properties comparable to those of

the CFC refrigerant R502 and virtually equal to
those of R404A. R507A has no ozone depletion
potential (ODP = 0) and is commonly accepted as
one of the best R502 alternatives. As with R404A,
R507A is particularly suitable for low evaporating temperature applications but it can also be
used for medium evaporating temperature applications. R507A is an azeotropic mixture with
no temperature glide. For low evaporating tem-
perature applications down to -45C, Maneurop

NTZ compressor should be used. Refer to the NTZ
selection and application guidelines. For medium
temperature R507A applications, always use the
Maneurop MTZ compressor and Maneurop
160PZ polyolester oil which is supplied with the
MTZ compressor.
R22 based transitional

refrigerants
A wide variety of R22 based transitional refrigerants exist (also called service refrigerants or dropin blends). These were developed as temporary
R12 or R502 alternatives. Some examples are
R401A, R401B, R409A and R409B as R12 alternatives and R402A, R402B, R403A and R403B as R502
alternatives. Because of the R22 component, they

all have a (low) ozone depletion potential. Maneurop MT compressors can be applied with these
transitional refrigerants. The initial mineral oil
charge must be replaced by Maneurop160 ABM
alkylbenzene oil.
Hydrocarbons
Hydrocarbons such as propane, isobutane etc. are

extremely ammable. Danfoss does not authorise
the use of hydrocarbons with Maneurop MT or
MTZ compressors in any way, even with a reduced

refrigerant charge.
R404A
R507A
18

used for R134a, even when the mineral oil is replaced by polyolester oil.
Maneurop MT compressors should never be used

for R404A, even with the mineral oil replaced by
polyolester oil.

used for R507A, even with the mineral oil replaced
by polyolester oil.
FRCC.PC.004.A4.02
System design recommendations
Piping design
Oil in a refrigeration circuit is required to lubricate moving parts in the compressor. During
normal system operation small oil quantities
will continuously leave the compressor, with the
discharge gas. With good system piping design
this oil will return to the compressor. As long as
the amount of oil circulating through the system
is small it will contribute to good system operation and improved heat transfer eciency. However, too large amounts of oil in the system will
have a negative eect on condenser and evaporator eciency. If, in a poorly designed system,
the amount of oil returning to the compressor

is lower than the amount of oil leaving the compressor, the compressor will become starved of
oil and the condenser, evaporator and/or refrigerant lines will become lled with oil. In such situations, additional oil charge will only correct the
compressor oil level for a limited period of time
and increase the amount of surplus oil in the rest
of the system.
Horizontal suction line sections shall have a slope

of 0.5% in the direction of refrigerant ow (5 mm
per meter). The cross-section of horizontal suction
lines shall be such that the resulting gas velocity is
at least 4 m/s. In vertical risers, a gas velocity of 8
to 12 m/s is required to ensure proper oil return. A
U-trap is required at the foot of each vertical riser.
If the riser is higher than 4 m, additional U-traps
are required for each additional 4 meters. The
length of each U-trap must be as short as possible
to avoid the accumulation of excessive quantities
of oil (see gure below).
will cause higher noise levels and result in higher

suction line pressure drops which will have a negative eect on the system capacity.
Suction lines
Only correct piping design can ensure a good oil

balance in the system.
For compressors mounted in parallel, the common suction riser should be designed as a double
riser. Also refer to the News bulletin "Mounting
instructions for installation of Maneurop compressors in parallel " and " Parallel application
guidelines".
Gas velocities higher than 12 m/s will not contribute to signicantly better oil return. However they
Note that the suction rotolock valves, which can
be ordered from Danfoss as accessories, are designed for average pipe sizes, selected for systems running at nominal conditions.
Discharge line
FRCC.PC.004.A4.02
The pipe sizes selected for specic systems may

dier from these recommended sizes.
It is recommended that the suction lines are insulated to limit suction gas superheat.
When the condenser is mounted above the compressor, a loop above the condenser and a U-trap
close to the compressor are required to prevent
liquid draining from the condenser into the discharge line during standstill.
19
Oil charge and oil separator
In most installations the initial compressor oil

charge will be sucient. In installations with line
runs exceeding 20 m, or with many oil traps or an
oil separator, additional oil may be required. In in-
stallations with the risk of slow oil return such as

in multiple evaporator or multiple condenser installations, an oil separator is recommended. Also
refer to page 26.
Filter driers
For new installations with MTZ compressors

Danfoss recommends using the Danfoss DML
100%-molecular sieve, solid core lter drier. Molecular sieve lter driers with loose beads from
third party suppliers shall be avoided.
lter driers containing activated alumina are recommended.
For servicing of existing installations where acid

formation is present the Danfoss DCL solid core
The drier is to be oversized rather than undersized. When selecting a drier, always take into
account its capacity (water content capacity), the
system refrigerating capacity and the system refrigerant charge.
Operating limits
High pressure
A high pressure safety switch is required to stop

the compressor, should the discharge pressure
exceed the values shown in the table below. The
high pressure switch can be set to lower values
depending on the application and ambient conditions. The HP switch must either be in a lock-
Low pressure
A low pressure safety switch is recommended to

avoid compressor operation at too lower suction
pressures.
Low ambient temperature

operation
20
out circuit, or be a manual reset device to prevent

compressor cycling around the high pressure limit. When a discharge valve is used, the HP switch
must be connected to the service valve gauge
port, which cannot be isolated.
MT
R22
MTZ
R407C
MTZ
R134a
MTZ
R404A / R507A
Test pressure low side
bar (g)
25
25
25
25
Working pressure range high side
bar (g)
10.9 - 27.7
12.5 - 29.4
7.9 - 22.6
13.2 - 27.7
Working pressure range low side
bar (g)
1.0 - 7.0
1.4 - 6.6
0.6 - 4.7
1.0 - 7.2
Relief valve opening pressure dierence
bar (g)
30
30
30
30
Relief valve closing pressure dierence
bar (g)
At low ambient temperatures, the condensing temperature and condensing pressure in air
cooled condensers will decrease.
discharge line is required and special care should

be taken when designing the discharge line.)
Reduce air ow to condensers.
This low pressure may be insucient to supply

enough liquid refrigerant to the evaporator. As
a result the evaporator temperature will strongly
decrease with the risk of frosting. At compressor
start-up, the compressor can pull a deep vacuum
and it can be switched o by the low pressure protection. Depending on the low pressure switch
setting and delay timer short cycling can occur. To
avoid these problems, several solutions are possible, based on reducing condenser capacity:
Indoor location of condensers
Liquid ooding of condensers (note: this solution
requires extra refrigerant charge, which can introduce other problems. A non-return valve in the
Other problems can also occur when the compressor is operating at low ambient temperature.
During shut down periods, liquid refrigerant can
migrate to a cold compressor.
For such conditions a belt-type crankcase heater
is strongly recommended.
Note that with 100% suction gas cooled motors,
Maneurop compressors can be externally insulated.
Refer to section "Liquid refrigerant migration &
charge limits" for more details.
FRCC.PC.004.A4.02
Operating voltage and cycle

rate
Operating voltage range
The operating voltage limits are shown in the table on page 4. The voltage applied to the motor
terminals must always be within these table limits. The maximum allowable voltage unbalance
for 3-phase compressors is 2%. Voltage unbalance
% voltage unbalance:
causes high current draw on one or more phases,

which in turn leads to overheating and possible
motor damage.
Voltage unbalance is given by the formula:
|Vavg - V1-2 |+|Vavg - V1-3 |+|Vavg - V2-3 |

2 xVavg
x 100
Vavg = Mean voltage of phases 1, 2 and 3

V1-2 = Voltage between phases 1 and 2
V1-3 = Voltage between phases 1 and 3

V2-3 = Voltage between phases 2 and 3.
Cycle rate limit
There may be no more than 12 starts per hour

(6 when a soft start accessory is used). A higher
number reduces the service life of the motorcompressor unit. If necessary, use an anti-shortcycle timer in the control circuit.
A time-out of six minutes is recommended. The

system must be designed in such a way to guarantee a minimum compressor running time in
order to provide proper oil return and sucient
motor cooling after starting.
Note that the oil return rate varies as a function of
the system design.
Liquid refrigerant control

and charge limit
Refrigeration compressors are basically designed

as gas compressors. Depending on the compressor design and operating conditions, most compressors can also handle a limited amount of
liquid refrigerant. Maneurop MT and MTZ compressors have a large internal volume and can
therefore handle relatively large amounts of liquid refrigerant without major problems. However
even when a compressor can handle liquid refrigerant, this will not be favourable to its service life.
Liquid refrigerant can dilute the oil, wash oil out

of bearings and result in high oil carry over, resulting in loss of oil from the sump. Good system design can limit the amount of liquid refrigerant in
the compressor, which will have a positive eect
on the compressor service life.
During system standstill and after pressure

equalisation, refrigerant will condense in the
coldest part of the system. The compressor can
easily be the coldest spot, for example when it is
placed outside in low ambient temperatures. After a while, the full system refrigerant charge can
condense in the compressor crankcase. A large
amount will dissolve in the compressor oil until
the oil is completely saturated with refrigerant. If
other system components are located at a higher level, this process can be even faster because
gravity will assist the liquid refrigerant to ow
back to the compressor. When the compressor is
started, the pressure in the crankcase decreases
rapidly.
At lower pressures the oil holds less refrigerant,

and as a result part of the refrigerant will violently
evaporate from the oil, causing the oil to foam.
This process is often called boiling.
During normal and stable system operation,

refrigerant will leave the evaporator in a superheated condition and enter the compressor as a
superheated vapour.
evaporator can contain an amount of liquid refrigerant due to dierent reasons:

wrong dimensioning, wrong setting or malfunction of expansion device
evaporator fan failure or blocked air lters.
In these situations, liquid refrigerant will continuously enter the compressor.
O-cycle migration
Liquid oodback during

operation
Normal superheat values at compressor suction

are 5 to 30 K. However the refrigerant leaving the
FRCC.PC.004.A4.02
Liquid refrigerant can enter a compressor in

dierent ways, with dierent eects on the
compressor.
The negative eects from migration on the compressor are:

oil dilution by liquid refrigerant
oil foam, transported by refrigerant gas and discharged into the system, causing loss of oil and in
extreme situations risk for oil slugging
in extreme situations with high system refrigerant charge, liquid slugging could occur (liquid entering the compressor cylinders).
21

The negative eects from continuous liquid
oodback are:
permanent oil dilution
in extreme situations with high system refrigerant charge and large amounts of oodback, liquid
slugging could occur.
Liquid oodback at change

over cycles in reversible heat
pumps
In heat pumps, change over from cooling to heating cycles, defrost and low load short cycles may
lead to liquid refrigerant oodback or saturated
refrigerant return conditions.
The negative eects are:

oil dilution
in extreme situations with high system refrigerant charge and large amounts of oodback, liquid
slugging could appear.
Liquid oodback and zeotropic refrigerants
Liquid oodback in systems working with a

zeotropic refrigerant such as R407C introduces
additional negative eects. A part of the
refrigerant leaves the evaporator in liquid phase
and this liquid has a dierent composition than
the vapour.
This new refrigerant composition may result in

dierent compressor operating pressures and
temperatures.
Crankcase heater
A crankcase heater protects against the o-cycle

migration of refrigerant and proves eective if
oil temperature is maintained 10 K above the
saturated LP temperature of the refrigerant. Tests
must thereby be conducted to ensure that the
appro-priate oil temperature is maintained under
all ambient conditions. A PTC crankcase heater is
recommended on all stand-alone compressors
and split systems. PTC crankcase heaters are selfregulating.
Belt crankcase heaters are not self-regulating.

Control must be applied to energise the belt
heater once the compressor has been stopped
and then to de-energise it while the compressor
is running. The belt heater must be energised 12
hours before restarting the compressor following
an extended down period.
Under extreme conditions such as very low ambient temperature a belt type crankcase heater
could be used in addition to the PTC heater, although this is not a preferred solution for 1 and 2
cylinder compressors. The belt crankcase heater
must be positioned on the compressor shell as
close as possible to the oil sump to ensure good
heat transfer to the oil.
Liquid line solenoid valve &
pump-down
Suction accumulator
If the crankcase heater is not able to maintain the

oil temperature at 10 K above the saturated LP
temperature of the refrigerant during o cycles
or if repetitive oodback is present a the Liquid
Line Solenoid Valve (LLSV) + pump-down cycle is
required, eventually in conjunction with a suction
accumulator.
In refrigeration applications, the Liquid Line Solenoid Valve (LLSV) is highly recommended. During
the o-cycle, the LLSV isolates the liquid charge
in the condenser side, thus preventing against
refrigerant transfer or excessive migration of refrigerant into the compressor. Furthermore, when
using a LLSV in conjunction with a pump-down
cycle, the quantity of refrigerant in the low-pressure side of the system will be reduced.
A suction accumulator oers considerable protection against refrigerant oodback at start-up,

during operation or after the defrost operation.
This device also helps to protect against o-cycle
migration by means of providing additional internal free volume to the low pressure side of the
system.
recommendations. As a general rule, Danfoss

recommends to size the accumulator for at least
50% of the total system charge. Tests however
must be conducted to determine the optimal
size.
A pump-down cycle design is required when

evaporators are tted with electric defrost heaters.
A suction accumulator shall not be used in systems with zeotropic refrigerant mixtures.
The suction accumulator must be selected in

accordance with the accumulator manufacturer
22
FRCC.PC.004.A4.02
Sound and vibration management
Sound
Running compressors cause sound and vibration.

Both phenomena are closely related.
Sound produced by a compressor is transmitted
in every direction by the ambient air, the mounting feet, the pipework and the refrigerant in the
pipework.
The easiest way to reduce the sound transmitted
through ambient air is to t a Danfoss acoustic
hood accessory.
Sound power level at 50 Hz

dB(A)
Because Maneurop compressors are 100% suction gas cooled, and require no body cooling,
they can be insulated. Values for the sound reduction achieved with acoustic hoods are shown
also in the table on the right. For inside mounted
compressors, sound insulation of the plantroom
is an alternative to sound insulation of the compressor.
Sound transmitted by mounting feet, pipework
and refrigerant should be treated the same way
as for vibration. Please refer to the next section.
Sound power level at 60 Hz
dB(A)
without hood
with hood*
without hood
with hood*
MTZ018
73
65
73
66
MTZ022
74
68
77
71
MTZ028
71
64
73
66
MTZ032
71
64
73
66
MTZ036
70
64
76
69
MTZ040
70
65
72
67
MTZ044
80
74
82
76
MTZ045
80
74
82
76
MTZ050
83
76
84
78
MTZ051
83
76
84
78
MTZ056
81
74
81
74
MTZ057
81
74
81
74
MTZ064
80
74
84
78
MTZ065
80
74
84
78
MTZ072
79
72
82
75
MTZ073
79
72
82
75
MTZ080
79
73
84
78
MTZ081
79
73
84
78
MTZ100
85
79
87
81
MTZ125
84
78
86
80
MTZ144
83
77
86
80
MTZ160
83
77
86
80
Acoustic hood
accessory
7755001
7755002
7755003
Sound power level for MTZ with R404A, motor code 4

Te = -10C, TC = 45C
* Sound data with hood are valid for the Danfoss acoustic hood accessory.
As rst approach, use these gures with -3 dBA reduction for MT models applied with R22.
Vibration
The mounting grommets delivered with the compressor should always be used. They reduce the
vibration transmitted by the compressor mounting feet to the base frame.
The base on which the compressor is mounted
should be suciently rigid and of adequate mass
to ensure the full eectiveness of the mounting
grommets.
The compressor should never be directly mounted to the base frame without the grommets, otherwise high vibration transmission would occur
and the compressor service life reduced. Suction
and discharge lines must have adequate exibility in 3 planes. Eventually vibration absorbers may
be required.
FRCC.PC.004.A4.02
Care must be taken to avoid tubing having resonant frequencies close to those of the compressor
frequency.
Vibration is also transmitted by the refrigerant
gas. Maneurop compressors have built in mufers to reduce this vibration.
To further reduce vibration an extra muer can
be installed.
Note: Maneurop MT & MTZ compressors have
been designed and qualied for stationary equipment used in A/C and Refrigeration applications.
Danfoss doesnt warrant these compressors for
use in mobile applications, such as trucks, railways, subways, etc...
23
Installation and service
System cleanliness
System contamination is one of the main factors

aecting equipment reliability and compressor
service life.
Therefore it is important to ensure system cleanliness when manufacturing a refrigeration system.
During the manufacturing process, system contamination can be caused by:
Brazing and welding oxides
Filings and particles from removing burrs from
pipe-work
Brazing ux
Moisture and air.
Clean all parts before brazing and always purge

nitrogen or CO2 through the pipes during brazing
to prevent oxidation. If ux is used, take every
precaution to prevent leakage into the piping. Do
not drill holes (e.g. for schrder valves) in parts of
the installation that are already completed, when
lings and burrs can not be removed. Carefully
follow the instructions below regarding brazing,
mounting, leak detection, pressure test and
moisture removal. All installation and service
work shall only be done by qualied personnel
respecting all procedures and using tools
(charging systems, tubes, vacuum pump, etc.)
dedicated for the refrigerant that will be used.
Only use clean and dehydrated refrigeration grade

copper tubes and silver alloy brazing material.
Compressor handling,
mounting and connection to
the system
Compressor handling
Compressor mounting
Maneurop MT and MTZ compressors are provided with a lifting lug. This lug should always be
used to lift the compressor. Once the compressor
is installed, the compressor lifting lug should nev-
er be used to lift the complete installation.
Mount the compressor on a horizontal plane with

a maximum slope of 3 degrees. All compressors
are supplied with three or four rubber mounting
grommets, each complete with metal sleeves and
nuts and bolts. Refer to the outline drawings on
page 10 to 12.
These grommets largely attenuate the compressor vibration transmitted to the base frame. The
compressor must always be mounted with these
grommets. Refer to the table below for torque
values.
Keep the compressor in an upright position during handling.
Designation
Cable screw of T connector in electrical box
Recommended torque (Nm)

screw 10/32 - UNF x 3
1"
80
1"1/4
90
Rotolock valves and solder sleeves
Mounting grommet bolts

Oil sight glass
Oil equalisation connection
Compressor connection to the

system
24
1"3/4
110
1 - 2 - 4 cylinder
15
50
1 - 2 - 4 cylinder
30
New compressors have a protective nitrogen

holding charge. The suction and discharge caps
should only be removed just before connecting
the compressor to the installation to avoid air and
moisture entering the compressor.
mounted. When all brazing is nished and when

the total system is ready, the compressor caps
can be removed and the compressor can be connected to the system with a minimum exposure
to ambient air.
Whenever possible the compressor must be the

last component to be integrated in the system. It
is advisable to braze the solder sleeves or service
valves to the pipework before the compressor is
If this procedure is not possible, the sleeves or

valves may be brazed to the pipes when mounted
on the compressor.
FRCC.PC.004.A4.02

In this situation nitrogen or CO2 must be purged
through the compressor via the schrader valve to
prevent air and moisture ingress. Purging must
start when the caps are removed and proceeded
during the brazing process.
When rotolock valves are used on the compressor,
they shall be closed immediately after mounting,
thus keeping the compressor isolated from atmosphere or from a not yet dehydrated system.
System pressure test
It is recommended that an inert gas such as nitrogen be used for pressure testing. Dry air may
also be used but care should be taken since it can
form an inammable mixture with the compressor oil. When performing a system pressure test,
the maximum allowed pressure for the dierent
components should not be exceeded.
For MT/MTZ compressors the maximum test pressures are shown in the table beside.
Leak detection
Whenever possible (if valves are present) the

compressor must be kept isolated from the
system. Perform a leak detection using the nal
refrigerant. Pressurise with nitrogen or another
neutral gas and use a leak detector for the applied
refrigerant. Any spectrometric detection system
using helium can also be applied.
Eventual leaks shall be repaired respecting the
instructions written above. It is not recommended
to use other gasses such as oxygen, dry air or
acetylene as these gasses can form an inammable
Vacuum pull-down moisture

removal
Moisture obstructs the proper functioning of the

compressor and the refrigeration system.
Air and moisture reduce service life and increase
condensing pressure, and cause excessively high
discharge temperatures, which can destroy the
FRCC.PC.004.A4.02
Note: When the compressor is built into a pack

or rack conguration which is not installed immediately on its nal location, a vacuum pulldown and moisture removal must be performed
to this pack (rack) as if it were a complete system
(see below). The pack must be charged with nitrogen or CO2 and open tubes must be blocked with
caps or plugs.
1-2-4 cylinder
compressors
Maximum compressor test pressure,
low side
25 bar(g)
Maximum compressor test pressure,

high side
30 bar(g)
Do not exceed 30 bar pressure dierence between high pressure side and low pressure side of
the compressor because this will open the internal compressor relief valve.
mixture. Never use CFC or HCFC refrigerants for

leak detection of HFC systems.
Note 1: Leak detection with refrigerant may not
be allowed in some countries. Check local regulations.
Note 2: Leak detecting additives shall not be used
as they may aect the lubricant properties.
Warranty may be voided if leak detecting additives have been used.
lubricating properties of the oil. Air and moisture

also increase the risk of acid formation, giving
rise to copper platting. All these phenomena can
cause mechanical and electrical compressor failure.
25

To eliminate these factors, a vacuum pull-down
according to the following procedure is recommended:
c Whenever possible (if valves are present) the
compressor must be kept isolated from the system.
d After the leak detection, the system must be
pulled-down under a vacuum of 500 microns
(0.67 mbar). A two stage vacuum pump shall be
used with a capacity appropriate to the system
volume. It is recommended to use connection
lines with a large diameter and to connect these
to the service valves and not to the schrader
connection to avoid too high pressure losses.
e When the vacuum level of 500 micron is
reached, the system must be isolated from the
vacuum pump. Wait 30 minutes during which
the system pressure should not rise. When the
pressure rapidly increases, the system is not leak
tight.
A new leak detection must be performed and the

vacuum pull-down procedure should be restarted from step 1. When the pressure slowly increases, this indicates the presence of moisture. In this
case step 2 and 3 should be repeated.
f Connect the compressor to the system by
opening the valves. Repeat step 2 and 3.
g Break the vacuum with nitrogen or the nal
refrigerant.
h Repeat step 2 and 3 on the total system.
At commissioning, system moisture content may
be up to 100 ppm. During operation the lter drier must reduce this to a level < 20 ppm.
Start-up
Before initial start-up or after a prolonged shut

down period, energise the crankcase heater (if
tted) 12 hours prior to start-up, or turn on power

for single phase compressors with trickle circuit.
Refrigerant charging
Zeotropic and near-azeotropic refrigerant

mixtures such as R407C and R404A must always
be charged in the liquid phase. For the initial
charge, the compressor must not run and service
valves must be closed. Charge refrigerant as
close as possible to the nominal system charge
before starting the compressor. Then slowly
add refrigerant in the liquid phase, on the low
pressure side as far away as possible from the
running compressor.
The refrigerant charge quantity must be suitable

for both winter and summer operation. Refer also
to section Protection against ooded starts and
liquid oodback for information about refrigerant charge limits.
The oil charge must be checked before commissioning (1/4 to 3/4 of the oil sight glass). Check the
oil level again after a minimum of 2 hours operation at nominal conditions. In most installations
the initial compressor oil charge will be sucient.
In installations with line runs exceeding 20 m or
with many oil traps or an oil separator, additional
oil may be required. Normally the quantity of oil
added should be no more than 2% of the total
refrigerant charge (this percentage does not take
into account oil contained in accessories such
as oil separators or oil traps). If this amount has

already been added and the oil level in the compressor keeps decreasing, the oil return in the installation is insucient. Refer also to section "Piping design".
The optimum suction gas superheat is 8 K. A

lower superheat value will contribute to better
system performance (higher mass ow and more
ecient use of evaporator surface). Low superheat values however increase the riskof unwanted
liquid oodback to the compressor.
The maximum allowable superheat is about 30 K.

Higher values can be accepted but in these cases,
tests have to be performed to check that the maximum discharge temperature of 130C will not be
exceeded. Note that high superheat values decrease the compressor application envelope and
system performance.
Oil charge and oil level
Suction gas superheat
Warning : Do not use a megohmmeter or apply

power to the compressor while it is under vacuum, as this may cause motor winding damage.
Never run the compressor under vacuum as it
may cause compressor motor burn-out.
Warning: when a liquid line solenoid valve is used,

the vacuum in the low pressure side must be
broken before applying power to the system.
In installations where slow oil return is likely such

as in multiple evaporator or multiple condenser
installations, an oil separator is recommended.
Refer to the table on page 17 to select the correct
oil.
For very low superheat values an electronically

controlled expansion valve is recommended.
26
FRCC.PC.004.A4.02
Ordering information and packaging
Packaging
Single pack
4 cylinders
2 cylinders
1 cylinder
Model
Dimensions
(mm)
Gross
weight
(kg)
Multipack
Nbr
Dimensions
(mm)
Gross
weight
(kg)
Industrial pack
Static
stacking
Nbr
Dimensions
(mm)
Gross
weight
(kg)
MT/MTZ 018
23
197
278
MT/MTZ 022
23
197
278
l: 330
w: 295
h: 385
MT/MTZ 028
MT/MTZ 032
25
8
26
l: 1150
w: 800
h: 510
213
4
12
221
l: 1150
w: 800
h: 500
302
4
314
MT/MTZ 036
27
229
326
MT/MTZ 040
27
229
326
MT/MTZ 044-050
37
232
224
MT/MTZ 045-051
39
244
236
MT/MTZ 056-064
MT/MTZ 057-065
l: 395
w: 365
h: 455
39
6
41
l: 1150
w: 800
h: 600
244
4
256
l: 1150
w: 800
h: 600
236
4
248
MT/MTZ 072-080
42
262
254
MT/MTZ 073-081
43
268
260
MT/MTZ 100
70
291
381
MT/MTZ 125
MT/MTZ 144
MT/MTZ 160
l: 570
w: 400
h: 670
73
4
76
78
l: 1150
w: 800
h: 820
303
4
315
323
l: 1150
w: 800
h: 710
399
4
417
429
Single pack:
One compressor in a cardboard box.

In some publications this packaging may be indicated as individual packaging.
Multipack:
A full pallet of compressors, each individually packed in a cardboard box. Mainly dedicated to wholesalers and Danfoss
distribution centers.
Industrial pack:
A full pallet of unpacked compressors. Mainly dedicated to OEM customers.

In some publications this packaging may be indicated as Multiple packaging.
Nbr:
Number of compressor in a pack
FRCC.PC.004.A4.02
Static
stacking
27
R22
MT compressors in industrial pack
Compressor
model
Design1)
1
208-230/1/60
3
200-230/3/60
S
MT18-3M
VE
MT18-1VM
MT18-3VM
S
MT22-1M
MT22-3M
MT022
VE
MT22-1VM
MT22-3VM
S
MT28-1M
MT28-3M
MT028
VE
MT28-1VM
MT28-3VM
S
MT32-3M
MT032
VE
MT32-1VM
MT32-3VM
S
MT36-3M
MT036
VE
MT36-1VM
MT36-3VM
S
MT40-1M
MT40-3M
MT040
VE
MT40-1VM
MT40-3VM
S
MT44-1M
MT44-3M
MT044
VE
MT44-1VM
MT44-3VM
S
MT045
VE
MT45-3VM
S
MT50-3M
MT050
VE
MT50-1VM
MT50-3VM
S
MT51-3M
MT051
VE
MT51-3VM
S
MT56-3M
MT056
VE
MT56-1VM
MT56-3VM
S
MT057
VE
MT57-3VM
S
MT64-3M
MT064
VE
MT64-1VM
MT64-3VM
S
MT65-3M
MT065
VE
MT65-3VM
S
MT72-3M
MT072
VE
MT72-3VM
S
MT73-3M
MT073
VE
MT73-3VM
S
MT080
VE
MT80-3VM
S
MT081
VE
MT81-3VM
Sv
MT100-3M
MT100
VE
MT100-3VM
Sv
MT125-3M
MT125
VE
MT125-3VM
Sv
MT144-3M
MT144
VE
MT144-3VM
Sv
MT160-3M
MT160
VE
MT160-3VM
1
) S = Single compressor, no oil sight glass, no oil equalisation connection
SV = Single compressor, welded oil sight glass, no oil equalisation connection
VE = Single compressor, threaded oil sight glass, 3/8" oil equalisation connection
MT018
28
Code no.
4
460/3/60
400/3/50
230/1/50
380/3/60
MT18-4M
MT18-4VM
MT22-4M
MT22-4VM
MT28-4M
MT28-4VM
MT32-4M
MT32-4VM
MT36-4M
MT36-4VM
MT40-4M
MT40-4VM
MT44-4M
MT44-4VM
MT45-4M
MT45-4VM
MT50-4M
MT50-4VM
MT51-4M
MT51-4VM
MT56-4M
MT56-4VM
MT57-4M
MT57-4VM
MT64-4M
MT64-4VM
MT65-4M
MT65-4VM
MT72-4M
MT72-4VM
MT73-4M
MT73-4VM
MT80-4M
MT80-4VM
MT81-4M
MT81-4VM
MT100-4M
MT100-4VM
MT125-4M
MT125-4VM
MT144-4M
MT144-4VM
MT160-4M
MT160-4VM
MT18-5M
MT18-5VM
MT22-5M
MT22-5VM
MT28-5M
MT28-5VM
MT32-5M
MT32-5VM
MT36-5M
MT36-5VM
MT50-5VM
-
MT22-9VM
MT28-9VM
MT32-9VM
MT36-9VM
MT44-9M
MT44-9VM
MT50-9M
MT50-9VM
MT56-9M
MT56-9VM
MT64-9M
MT64-9VM
MT72-9M
MT72-9VM
MT80-9M
MT80-9VM
MT100-9M
MT100-9VM
MT125-9VM
MT125-9VM
MT144-9M
MT144-9VM
MT160-9M
MT160-9VM
FRCC.PC.004.A4.02
R22
MT compressors in single pack
Compressor
model
MT018
MT022
MT028
MT032
MT036
MT040
MT044
MT045
MT050
MT051
MT056
MT057
MT064
MT065
MT072
MT073
MT080
MT081
MT100
MT125
MT144
MT160
Design1)
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
208-230/1/60
200-230/3/60
460/3/60
400/3/50
MT18-1VI
MT22-1VI
MT28-1VI
MT32-1VI
MT36-1VI
MT40-1VI
MT44-1VI
MT50-1VI
MT56-1VI
MT64-1VI
-
MT18-3VI
MT22-3VI
MT28-3VI
MT32-3VI
MT36-3VI
MT40-3VI
MT44-3VI
MT45-3VI
MT50-3VI
MT51-3VI
MT56-3VI
MT57-3VI
MT64-3VI
MT65-3VI
MT72-3VI
MT73-3VI
MT80-3VI
MT81-3VI
MT100-3VI
MT125-3VI
MT144-3VI
MT160-3VI
MT18-4VI
MT22-4VI
MT28-4VI
MT32-4VI
MT36-4VI
MT40-4VI
MT44-4VI
MT45-4VI
MT50-4VI
MT51-4VI
MT56-4VI
MT57-4VI
MT64-4VI
MT65-4VI
MT72-4VI
MT73-4VI
MT80-4VI
MT81-4VI
MT100-4VI
MT125-4VI
MT144-4VI
MT160-4VI
Code no.
5
230/1/50
230/3/50
575/3/60
500/3/50
380/3/60
MT18-5VI
MT22-5VI
MT28-5VI
MT32-5VI
MT36-5VI
MT50-5VI
-
MT22-6VI
MT28-6VI
MT32-6VI
MT36-6VI
MT40-6VI
MT44-6VI
MT50-6VI
MT56-6VI
MT64-6VI
MT72-6VI
MT80-6VI
MT100-6VI
MT125-6VI
MT144-6VI
MT160-6VI
MT44-7VI
MT50-7VI
MT56-7VI
MT100-7VI
MT125-7VI
MT144-7VI
MT160-7VI
MT22-9VI
MT28-9VI
MT32-9VI
MT36-9VI
MT44-9VI
MT50-9VI
MT56-9VI
MT64-9VI
MT72-9VI
MT80-9VI
MT100-9VI
MT125-9VI
MT144-9VI
MT160-9VI
) VE = Single compressor, threaded oil sight glass, 3/8" oil equalisation connection
FRCC.PC.004.A4.02
29
MTZ compressors in industrial pack
Compressor
model
Design1)
1
208-230/1/60
3
200-230/3/60
MTZ18-1M
MTZ18-3M
MTZ18-1VM
MTZ18-3VM
MTZ22-1M
MTZ22-3M
MTZ022
MTZ22-1VM
MTZ22-3VM
MTZ28-1M
MTZ28-3M
MTZ028
MTZ28-1VM
MTZ28-3VM
MTZ32-1M
MTZ32-3M
MTZ032
MTZ32-1VM
MTZ32-3VM
MTZ36-1M
MTZ36-3M
MTZ036
MTZ36-1VM
MTZ36-3VM
MTZ40-1M
MTZ40-3M
MTZ040
MTZ40-1VM
MTZ40-3VM
MTZ44-3M
MTZ044
MTZ44-1VM
MTZ44-3VM
MTZ045
MTZ45-3VM
MTZ50-3M
MTZ050
MTZ50-1VM
MTZ50-3VM
MTZ051
MTZ51-3VM
MTZ56-3M
MTZ056
MTZ56-1VM
MTZ56-3VM
MTZ057
MTZ57-3VM
MTZ64-3M
MTZ064
MTZ64-1VM
MTZ64-3VM
MTZ065
MTZ65-3VM
MTZ72-3M
MTZ072
MTZ72-3VM
MTZ073
MTZ73-3VM
MTZ080
MTZ80-3VM
MTZ081
MTZ81-3VM
MTZ100-3M
MTZ100
MTZ100-3VM
MTZ125-3M
MTZ125
MTZ125-3VM
MTZ144-3M
MTZ144
MTZ144-3VM
MTZ160-3M
MTZ160
VE
MTZ160-3VM
1
) S = Single compressor, no oil sight glass, no oil equalisation connection
Sv = Single compressor, welded oil sight glass, no oil equalisation connection
VE = Single compressor, threaded oil sight glass, 3/8" oil equalisation connection
MTZ018
30
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
S
VE
Sv
VE
Sv
VE
Sv
VE
Sv
R404A / R507A / R134a / R407C

Code no.
4
460/3/60
400/3/50
230/1/50
380/3/60
MTZ18-4M
MTZ18-4VM
MTZ22-4M
MTZ22-4VM
MTZ28-4M
MTZ28-4VM
MTZ32-4M
MTZ32-4VM
MTZ36-4M
MTZ36-4VM
MTZ40-4M
MTZ40-4VM
MTZ44-4M
MTZ44-4VM
MTZ45-4M
MTZ45-4VM
MTZ50-4M
MTZ50-4VM
MTZ51-4M
MTZ51-4VM
MTZ56-4M
MTZ56-4VM
MTZ57-4M
MTZ57-4VM
MTZ64-4M
MTZ64-4VM
MTZ65-4M
MTZ65-4VM
MTZ72-4M
MTZ72-4VM
MTZ73-4M
MTZ73-4VM
MTZ80-4M
MTZ80-4VM
MTZ81-4M
MTZ81-4VM
MTZ100-4M
MTZ100-4VM
MTZ125-4M
MTZ125-4VM
MTZ144-4M
MTZ144-4VM
MTZ160-4M
MTZ160-4VM
MTZ18-5M
MTZ18-5VM
MTZ22-5M
MTZ22-5VM
MTZ28-5M
MTZ28-5VM
MTZ32-5M
MTZ32-5VM
MTZ36-5M
MTZ36-5VM
MTZ50-5VM
-
MTZ22-9VM
MTZ28-9VM
MTZ32-9VM
MTZ36-9VM
MTZ44-9M
MTZ44-9VM
MTZ50-9M
MTZ50-9VM
MTZ56-9M
MTZ56-9VM
MTZ64-9M
MTZ64-9VM
MTZ72-9M
MTZ72-9VM
MTZ80-9M
MTZ80-9VM
MTZ100-9M
MTZ100-9VM
MTZ125-9M
MTZ125-9VM
MTZ144-9M
MTZ144-9VM
MTZ160-9M
MTZ160-9VM
FRCC.PC.004.A4.02
R404A / R507A / R134a / R407C
MTZ compressors in single pack
Compressor
model
MTZ018
MTZ022
MTZ028
MTZ032
MTZ036
MTZ040
MTZ044
MTZ045
MTZ050
MTZ051
MTZ056
MTZ057
MTZ064
MTZ065
MTZ072
MTZ073
MTZ080
MTZ081
MTZ100
MTZ125
MTZ144
MTZ160
Design1)
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
VE
208-230/1/60
200-230/3/60
460/3/60
400/3/50
MTZ18-1VI
MTZ22-1VI
MTZ28-1VI
MTZ32-1VI
MTZ36-1VI
MTZ40-1VI
MTZ44-1VI
MTZ50-1VI
MTZ56-1VI
MTZ64-1VI
-
MTZ18-3VI
MTZ22-3VI
MTZ28-3VI
MTZ32-3VI
MTZ36-3VI
MTZ40-3VI
MTZ44-3VI
MTZ45-3VI
MTZ50-3VI
MTZ51-3VI
MTZ56-3VI
MTZ57-3VI
MTZ64-3VI
MTZ65-3VI
MTZ72-3VI
MTZ73-3VI
MTZ80-3VI
MTZ81-3VI
MTZ100-3VI
MTZ125-3VI
MTZ144-3VI
MTZ160-3VI
MTZ18-4VI
MTZ22-4VI
MTZ28-4VI
MTZ32-4VI
MTZ36-4VI
MTZ40-4VI
MTZ44-4VI
MTZ45-4VI
MTZ50-4VI
MTZ51-4VI
MTZ56-4VI
MTZ57-4VI
MTZ64-4VI
MTZ65-4VI
MTZ72-4VI
MTZ73-4VI
MTZ80-4VI
MTZ81-4VI
MTZ100-4VI
MTZ125-4VI
MTZ144-4VI
MTZ160-4VI
Code no.
5
230/1/50
230/3/50
575/3/60
500/3/50
380/3/60
MTZ18-5VI
MTZ22-5VI
MTZ28-5VI
MTZ32-5VI
MTZ36-5VI
MTZ50-5VI
-
MTZ22-6VI
MTZ28-6VI
MTZ32-6VI
MTZ36-6VI
MTZ40-6VI
MTZ44-6VI
MTZ50-6VI
MTZ56-6VI
MTZ64-6VI
MTZ72-6VI
MTZ80-6VI
MTZ100-6VI
MTZ125-6VI
MTZ144-6VI
MTZ160-6VI
MTZ32-7VI
MTZ36-7VI
MTZ44-7VI
MTZ50-7VI
MTZ56-7VI
MTZ100-7VI
MTZ125-7VI
MTZ144-7VI
MTZ160-7VI
MTZ22-9VI
MTZ28-9VI
MTZ32-9VI
MTZ36-9VI
MTZ44-9VI
MTZ50-9VI
MTZ56-9VI
MTZ64-9VI
MTZ72-9VI
MTZ80-9VI
MTZ100-9VI
MTZ125-9VI
MTZ144-9VI
MTZ160-9VI
) VE = Single compressor, threaded oil sight glass, 3/8" oil equalisation connection
FRCC.PC.004.A4.02
31
The Danfoss product range for the

refrigeration and air conditioning industry
Danfoss Refrigeration & Air Conditioning
is a worldwide manufacturer with a leading
position in industrial, commercial and
supermarket refrigeration as well as air
conditioning and climate solutions.
We focus on our core business of making

quality products, components and systems
that enhance performance and reduce total
life cycle costs the key to major savings.
Controls for
Commercial Refrigeration
Controls for
Industrial Refrigeration
Electronic Controls &

Sensors
Industrial Automation
Household Compressors
Commercial Compressors
Sub-Assemblies
Thermostats
Brazed plate
heat exchanger
We are oering a single source for one of the widest ranges of innovative refrigeration and air
conditioning components and systems in the world. And, we back technical
solutions with business solution to help your company reduce costs,
streamline processes and achieve your business goals.
Danfoss A/S www.danfoss.com
Danfoss Commercial Compressors http://cc.danfoss.com

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on
order provided that such alterations can be made without subsequential changes being necessary in specications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
FRCC.PC.004.A4.02 October 2008 - replace FRCC.PC.004.A3.02 Sept 2006
Produced by Danfoss CC- DSS - 10/2008

MS Maneurop Refigeration Compressors Spec Sheets

Uploaded by

Copyright:

Available Formats

MS Maneurop Refigeration Compressors Spec Sheets

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MS Maneurop Refigeration Compressors Spec Sheets

Uploaded by

Copyright:

Available Formats

MAKING MODERN LIVING POSSIBLE

Maneurop reciprocating compressors

MANEUROP RECIPROCATING COMPRESSORS .................................................................................................................................................................................. p 3

Maneurop reciprocating compressors

the HFC refrigerants R407C, R134a, R404A, and

Maneurop MT and MTZ series compressors are of

MT and MTZ compressors have a large internal

The compressor design allows for the motor to be

MT and MTZ compressors are fully suction-gas

MTZ compressors can be used in new installations

Compressor model designation

Oil equalisation port

Motor voltage code

Available code numbers are listed on pages 28-29

Motor voltage code

Oil sight glass

Approvals and certicates

Low voltage directive

Available in MT and MTZ

Available in MTZ only

Maneurop MT/MTZ compressors comply with

Certicates are listed on the product datasheets:

Depending on the model and motor voltage code.

Depending on the model and motor voltage code.

MT/ MTZ 44 to 160

MT/ MTZ 44 to 160

Manufacturer's declaration of incorporation

Internal free volume

Available motor voltage codes

1 cyl. with height = 356 mm (see page 10)

4 cyl . with height = 519 mm (see page 12)

4 cyl. with height = 540 mm (see page 12)

Nominal performance data for R404A and R22

50 Hz, ARI ratings

60 Hz, ARI ratings

To = -6.7 C, Tc = 48.9 C, SC = 0 K, SH = 11.1 K

To = -6.7 C, Tc = 48.9 C, SC = 0 K, SH = 11.1 K

* 50 Hz, EN12900 data for indicated models are Asercom certied

R404A data are also valid for refrigerant R507A

50 Hz, EN12900 ratings

50 Hz, ARI ratings

60 Hz, ARI ratings

To = +7.2C, Tc = 54.4 C, SC = 8.3 K, SH = 11.1 K

To = +7.2C, Tc = 54.4 C, SC = 8.3 K, SH = 11.1 K

To: Evaporating temperature at dew point (saturated suction temperature)

ARI capacity and power input data are +/- 5%

Nominal performance data for R407C and R134a

50 Hz, ARI ratings

60 Hz, ARI ratings

To = +7.2 C, Tc = 54.4 C, SC = 8.3 K, SH = 11.1 K

To = +7.2 C, Tc = 54.4 C, SC = 8.3 K, SH = 11.1 K

* 50 Hz, EN12900 data for indicated models are Asercom certied

50 Hz, ARI ratings

60 Hz, ARI ratings

To = +7.2 C, Tc = 54.4 C, SC = 8.3 K, SH = 11.1 K

To = +7.2 C, Tc = 54.4 C, SC = 8.3 K, SH = 11.1 K

To: Evaporating temperature at dew point (saturated suction temperature)

ARI capacity and power input data are +/- 5%

MTZ - R407C at DEW point

MTZ - R404A / R507A