E-2

API STANDARD 650

Dynamic analysis methods incorporating fluid-structure and soil-structure interaction are permitted to be used in lieu
of the procedures contained in this Annex with Purchaser approval and provided the design and construction details
are as safe as otherwise provided in this Annex.

E.2 Definitions and Notations

--```,,,``````,`,,,`,,,,,```,`,,-`-`,,`,,`,`,,`---

E.2.1.1
active fault
A fault for which there is an average historic slip rate of 1 mm (0.4 in.) per year or more and geologic evidence of
seismic activity within Holocene times (past 11,000 years).
E.2.1.2
characteristic earthquake
An earthquake assessed for an active fault having a magnitude equal to the best-estimate of the maximum
magnitude capable of occurring on the fault, but not less than the largest magnitude that has occurred historically on
the fault.
E.2.1.3
maximum considered earthquake
MCE
The most severe earthquake ground motion considered in this Annex.
E.2.1.4
mechanically-anchored tank
Tanks that have anchor bolts, straps or other mechanical devices to anchor the tank to the foundation.
E.2.1.5
self-anchored tank
Tanks that use the inherent stability of the self-weight of the tank and the stored product to resist overturning forces.
E.2.1.6
site class
A classification assigned to a site based on the types of soils present and their engineering properties as defined in
this Annex.

E.2.2 Notations
A

Lateral acceleration coefficient, %g

Ac

Convective design response spectrum acceleration parameter, = (2/3) x 0.7 x SDS = 0.47 SDS, %g

Af

Acceleration coefficient for sloshing wave height calculation, %g

Ai

Impulsive design response spectrum acceleration coefficient, %g

Av

Vertical earthquake acceleration parameter = (2/3) x 0.7 x SDS = 0.47 SDS, %g

Cd

Deflection amplification factor, Cd = 2

Ci

Coefficient for determining impulsive period of tank system

WELDED TANKS FOR OIL STORAGE

E-3

Nominal tank diameter, m (ft)

dc

Total thickness (100 ds) of cohesive soil layers in the top 30 m (100 ft)

di

Thickness of any soil layer i (between 0 and 30 m [100 ft])

ds

Total thickness of cohesionless soil layers in the top 30 m (100 ft)

Elastic Modulus of tank material, MPa (lbf/in.2)

Fa

Acceleration-based site coefficient (at 0.2 sec period)

Fc

Allowable longitudinal shell-membrane compression stress, MPa (lbf/in.2)

Fty

Minimum specified yield strength of shell course, MPa (lbf/in.2)

Fv

Velocity-based site coefficient (at 1.0 sec period)

Fy

Minimum specified yield strength of bottom annulus, MPa (lbf/in.2)

Specific gravity

Acceleration due to gravity in consistent units, m/sec2 (ft/sec2)

Ge

Effective specific gravity including vertical seismic effects = G (1 0.4Av)

Maximum design product level, m (ft)

HS

Thickness of soil, m (ft)

Importance factor coefficient set by seismic use group

Anchorage ratio

Coefficient to adjust the spectral acceleration from 5 % to 0.5 % damping = 1.5 unless otherwise specified

Required minimum width of thickened bottom annular ring measured from the inside of the shell m (ft)

Ls

Selected width of annulus (bottom or thickened annular ring) to provide the resisting force for self
anchorage, measured from the inside of the shell m (ft)

ta

Thickness, excluding corrosion allowance, mm (in.) of the bottom annulus under the shell required to
provide the resisting force for self anchorage. The bottom plate for this thickness shall extend radially at
least the distance, L, from the inside of the shell. This term applies for self-anchored tanks only.

Mrw

Ringwall momentPortion of the total overturning moment that acts at the base of the tank shell
perimeter, Nm (ft-lb)

Ms

Slab moment (used for slab and pile cap design), Nm (ft-lb)

Standard penetration resistance, ASTM D1586

Average field standard penetration test for the top 30 m (100 ft)
--```,,,``````,`,,,`,,,,,```,`,,-`-`,,`,,`,`,,`---

E-4

API STANDARD 650

nA

Number of equally-spaced anchors around the tank circumference

Nc

Convective hoop membrane force in tank shell, N/mm (lbf/in.)

Nch

Average standard penetration of cohesionless soil layers for the top 30 m (100 ft)

Nh

Product hydrostatic membrane force, N/mm (lbf/in.)

Ni

Impulsive hoop membrane force in tank shell, N/mm (lbf/in.)

PA

Anchorage attachment design load, N (lbf)

PAB

Anchor design load, N (lbf)

Pf

Overturning bearing force based on the maximum longitudinal shell compression at the base of shell, N/m
(lbf/ft)

PI

Plasticity index, ASTM D4318

Scaling factor from the MCE to the design level spectral accelerations; equals 2/3 for ASCE 7

Force reduction coefficient for strength level design methods

Rwc

Force reduction coefficient for the convective mode using allowable stress design methods

Rwi

Force reduction factor for the impulsive mode using allowable stress design methods

S0

Mapped, maximum considered earthquake, 5 % damped, spectral response acceleration parameter at a

S1

Mapped, maximum considered earthquake, 5 % damped, spectral response acceleration parameter at a

Sa

The 5 % damped, design spectral response acceleration parameter at any period based on mapped,
probabilistic procedures, %g

Sa*

The 5 % damped, design spectral response acceleration parameter at any period based on site-specific
procedures, %g

Sa0*

The 5 % damped, design spectral response acceleration parameter at zero period based on site-specific
procedures, %g

SD1

The design, 5 % damped, spectral response acceleration parameter at one second based on the ASCE 7
methods, equals Q Fv S1, %g

SDS

The design, 5% damped, spectral response acceleration parameter at short periods (T = 0.2 seconds)
based on ASCE 7 methods, equals Q Fa Ss, %g

SP

Design level peak ground acceleration parameter for sites not addressed by ASCE methods. [See EC
Example Problem 2 when using Z factor from earlier editions of API 650 and UBC. Since 475 year
recurrence interval is basis of this peak ground acceleration, Q = 1.0 (no scaling).]

SS

Mapped, maximum considered earthquake, 5% damped, spectral response acceleration parameter at

su

Undrained shear strength, ASTM D2166 or ASTM D2850

WELDED TANKS FOR OIL STORAGE

E-5

su

Average undrained shear strength in top 30 m (100 ft)

Thickness of the shell ring under consideration, mm (in.)

ta

Thickness, excluding corrosion allowance, mm (in.) of the bottom annulus under the shell required to
provide the resisting force for self anchorage. The bottom plate for this thickness shall extend radially at
least the distance, L, from the inside of the shell. this term applies for self-anchored tanks only.

tb

Thickness of tank bottom less corrosion allowance, mm (in.)

ts

Thickness of bottom shell course less corrosion allowance, mm (in.)

tu

Equivalent uniform thickness of tank shell, mm (in.)

Natural period of vibration of the tank and contents, seconds

TC

Natural period of the convective (sloshing) mode of behavior of the liquid, seconds

Ti

Natural period of vibration for impulsive mode of behavior, seconds

TL

Regional-dependent transition period for longer period ground motion, seconds

T0

0.2 FvS1 / FaSS

TS

FvS1 / FaSS

Total design base shear, N (lbf)

Vc

Design base shear due to the convective component of the effective sloshing weight, N (lbf)

vs

Average shear wave velocity at large strain levels for the soils beneath the foundation, m/s (ft/s)

vs

Average shear wave velocity in top one 30 m (100 ft), m/s (ft/s)

Vi

Design base shear due to impulsive component from effective weight of tank and contents, N (lbf)

Moisture content (in %), ASTM D2216

wa

Force resisting uplift in annular region, N/m (lbf/ft)

wAB

Calculated design uplift load on anchors per unit circumferential length, N/m (lbf/ft)

Wc

Effective convective (sloshing) portion of the liquid weight, N (lbf)

Weff

Effective weight contributing to seismic response

Wf

Weight of the tank bottom, N (lbf)

Wfd

Total weight of tank foundation, N (lbf)

Wg

Weight of soil directly over tank foundation footing, N (lbf)

Wi

Effective impulsive portion of the liquid weight, N (lbf)

wint

Calculated design uplift load due to product pressure per unit circumferential length, N/m (lbf/ft)
--```,,,``````,`,,,`,,,,,```,`,,-`-`,,`,,`,`,,`---

E-6

API STANDARD 650

Wp

Total weight of the tank contents based on the design specific gravity of the product, N (lbf)

Wr

Total weight of fixed tank roof including framing, knuckles, any permanent attachments and 10 % of the
roof design snow load, N (lbf)

Wrs

Roof load acting on the tank shell including 10 % of the roof design snow load, N (lbf)

wrs

Roof load acting on the shell, including 10 % of the specified snow load N/m (lbf/ft)

Ws

Total weight of tank shell and appurtenances, N (lbf)

WT

Total weight of tank shell, roof, framing, knuckles, product, bottom, attachments, appurtenances,
participating snow load, if specified, and appurtenances, N (lbf)

wt

Tank and roof weight acting at base of shell, N/m (lbf/ft)

Xc

Height from the bottom of the tank shell to the center of action of lateral seismic force related to the
convective liquid force for ringwall moment, m (ft)

Xcs

Height from the bottom of the tank shell to the center of action of lateral seismic force related to the
convective liquid force for the slab moment, m (ft)

Xi

Height from the bottom of the tank shell to the center of action of the lateral seismic force related to the
impulsive liquid force for ringwall moment, m (ft)

Xis

Height from the bottom of the tank shell to the center of action of the lateral seismic force related to the
impulsive liquid force for the slab moment, m (ft)

Xr

Height from the bottom of the tank shell to the roof and roof appurtenances center of gravity, m (ft)

Xs

Height from the bottom of the tank shell to the shells center of gravity, m (ft)

Distance from liquid surface to analysis point, (positive down), m (ft)

yu

Estimated uplift displacement for self-anchored tank, mm (in.)

Maximum longitudinal shell compression stress, MPa (lbf/in.2)

Product hydrostatic hoop stress in the shell, MPa (lbf/in.2)

Hoop stress in the shell due to impulsive and convective forces of the stored liquid, MPa (lbf/in.2)

Total combined hoop stress in the shell, MPa (lbf/in.2)

--```,,,``````,`,,,`,,,,,```,`,,-`-`,,`,,`,`,,`---

Friction coefficient for tank sliding

Density of fluid, kg/m3 (lb/ft3)

E.3 Performance Basis