Scribd
Upload
132 views2 pages

Mechanical Measurements and Controls Apr2012

This document appears to be an exam for a measurement techniques and data analysis course. It contains 8 questions divided into two sections. The questions cover topics like: 1. Classifying and describing characteristics of measuring instruments. 2. Different types of data correlations, regression analysis, and determining correlation coefficients. 3. Principles and workings of various instruments for measuring temperature, flow, velocity, frequency and other process variables. 4. Control systems, vibration measurement, electromagnetic flow meters, thermistors, humidity measurement and thermal conductivity gauges.

Uploaded by

avinash_k007
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
132 views2 pages

Mechanical Measurements and Controls Apr2012

This document appears to be an exam for a measurement techniques and data analysis course. It contains 8 questions divided into two sections. The questions cover topics like: 1. Classifying and describing characteristics of measuring instruments. 2. Different types of data correlations, regression analysis, and determining correlation coefficients. 3. Principles and workings of various instruments for measuring temperature, flow, velocity, frequency and other process variables. 4. Control systems, vibration measurement, electromagnetic flow meters, thermistors, humidity measurement and thermal conductivity gauges.

Uploaded by

avinash_k007
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Total No.

of Questions : 8]

SEAT No. :

P1836

[Total No. of Pages : 2

[4165] - 504
M.E. (Mechanical) (Heat power Engg.)
MEASUREMENT TECHNIQUES & DATA ANALYSIS

(2008 Course) (Sem. - II)


Time :3 Hours]

[Max. Marks :100

Instructions to the candidates:


1) Answer any 3 questions from each section.
2) Answers to the two sections should be written in separate books.
3) Neat diagrams must be drawn wherever necessary.
4) Figures to the right indicate full marks.
5) Use of logarithmic tables slide rule, Mollier charts, electronic pocket
calculator and steam tables is allowed.
6) Assume suitable data if necessary.

SECTION - I
Q1) a) Explain classification of measuring instruments.
b) Explain static characteristics of an instrument.

[8]
[8]

Q2) a) Explain different types of correlations.

[8]

b) Find the most likely production corresponding to a rain fall 40'' from the
following data.
[8]
Rain fall
Production
Average
30''
500 kg
Standard deviation
5''
100 kg
Co - efficient of correlation = 0.8
Q3) a) What are properties of regression co - efficients?
[6]
b) Obtain the lines of regression from the data given.
[12]
X :
4
5
6
8 11
Y : 12 10 8
7
5
Verify that the co-efficient of correlation is geometric mean of two
co - efficients of regression.

P.T.O.

Q4) a) Explain the working of ultrasonic flow meter stating its merits & demerits.
[8]
b) A copper resistor at 20C is used to indicate the temperature of bearing,
of machine. What resistance should not be exceeded if maximum bearing
temp. is not to exceed 150C. The resistance temperature co-efficient of
copper is 0.00393 /C at 20C.
[8]
SECTION - II
Q5) a) Explain the principle construction and working of temperature measuring
device of a furnace.
[8]
b) A Laser Dopper anemometer employs a He - ne laser , O= 632.8 nm to
measure velocity of flow at a point in a dusty gas. A 160 mm focussing
lens having T = 12 is used to operate LDA in dual beam mode. Find the
velocity of flow if the average Doppler shift in frequency was found to
be 1.62 MHz.
[8]
Q6) a) Explain the working double beam - U - V spectrophotometer.

[8]

b) A disc mounted on the shaft of a machine has 12 pattern points. The


number of flashes projected on the disc by a stroboscope is 6000 per
minute.
[8]
i) Find the speed of the machine if the disc appears stationary and
has a single image of 12 points.
ii) If the disc appears to move forward in the direction of rotation at
10 rpm. Find the speed of the disc.
Q7) a) If r = 0.6, N = 64, find probable error of coefficient of correlation and
determine limits of population. r.
[4]
b) Explain P + I + D controller.

[8]

c) A miniature pitot tube is used to measure the velocity of blood and


differential pressure gauge records a pressure of 1 Torr. Take density of
[4]
blood = 1020 kg/m3 Compute the blood velocity.
Q8) Write short notes on any THREE
a) Vibration Measurement Instrument.
b) Electromagnetic flowmeter.
c) Thermistors.
d) Humidity measurement.
e) Thermal conductivity gauges.

[4165]-504

[18]

You might also like