The 560CMU02 communication unit is one of the CMU modules
of the RTU560 product line. The essential tasks are: Managing and controlling of the I/O modules via the interface to the serial I/O bus. Reading Process events from the input modules. Send commands to the output modules. Communicating with control systems and local HMI systems via the serial interfaces (RS232) and the Ethernet 10/100BaseT interfaces. Communication with Sub-RTUs, IEDs or multimeter devices via the interfaces (RS485) and the Ethernet interfaces. Managing the time base for the RTU560 station and synchronizing the I/O modules. Handling the dialog between RTU560 and Web-Browser via the LAN interfaces. Within the RTU560 racks the board occupies one slot. The communication unit is able to handle Ethernet-, UART- and non UART character based communication protocols.
SPB
Figure 1: Block diagram 560CMU02
Characteristics The two microprocessors are the essential hardware parts of the module, which share themselves in the tasks: MPU: 32 Bit Main Processing Unit SLC: 8 Bit Serial Line Controller One task of the SLC is to work as master for the SPB I/O bus (serial peripheral bus). In addition the SLC is the time base for the I/O modules and does the periodical time synchronization of the I/O modules. Depending on the configuration also serial protocols can be handled via the SLC. The MPU is responsible for the other tasks. The MPU handles the absolute time and date for the RTU. The real time clock 560RTC0x can be used for the time reference or the time may be set and synchronized from the central system via the serial lines or via the Ethernet LAN interface. RTU560 synchronizes it-
self to the time references supplied by 560RTC0x. The time information of the 560RTC0x is provided to the 560CMU02on the backplane of the sub-rack. System relevant configuration files are stored in the non-volatile flash memory card in order to guarantee a valid system configuration after Power on Reset (PoR). The communication unit provides the following interfaces: Communication Port 1 and 2 (CP1 & CP2): serial interfaces according RS232C or RS485 with RJ45 connectors. Ethernet Interface 1 and 2 (E1 & E2) Ethernet interface 10/100BaseT with RJ45 connector. The SPB I/O bus is directly connected to the backplane connector.
2 | 1KGT 150 717 V003 1 - Communication Unit 560CMU02
Technical data
Signaling by LEDs
In addition to the RTU500 series general technical data, the following applies:
ERR (red)
ON: RTU in error state
Flashing: RTU in warning state For more details see RTU500 series Function Description
Main Processing Unit MPU
CPU
Tx (green) (incorporating an Intel 586TMclass 32 bit processor)
RAM
Transmit data on serial communica-
ELAN520 @ 133 MHz
Serial Line Controller SLC
80C251
RAM
32 kByte
Dual ported RAM
16 kByte
Rx (green)
Receive data on serial communication
ports CP
64 MByte
CPU
tion ports CP
A (green)
Activity on Ethernet interface E
L (green)
Link up on Ethernet interface E
Mechanical layout Dimensions
160 mm x 100 mm, 3HE euro card
format 4R (20 mm) front panel
CompactFlash card
Housing type
Printed circuit board
Connector
CompactFlash card slot
Mounting
for mounting in RTU560 racks
Type
CF-Typ I (36,4 mm 42,8 mm 3,3
Weight
0.3 kg
mm) Capacity
128 MByte
Connection type RTU560 backplane connector
48 pole type F DIN 41612
Serial interfaces CP1 and CP2
Connector
RJ45
Immunity test
Type
RS232C or RS485
Electrostatic discharge
8 kV air (level 3) / 4 kV contact (level 2)
IEC 61000-4-2
Performance criteria A
Radiated Radio-Frequency Electro-
10 V/m (level 3)
magnetic Field
Performance criteria A
RS232C: Bit rate Signal lines
Level
50 bit/s - 38.4 kbit/s
GND
E2/102
TxD
D1/103
RxD
D2/104
IEC 61000-4-3 Electrical Fast Transient / Burst
2 kV (level 3)
IEC 61000-4-4
Performance criteria A
RTS
S2/105
CTS
M2/106
Surge
2 kV (level 3)
DTR
S1.2/108
IEC 61000-4-5
Performance criteria A
DCD
M5/109
Conducted Disturbances, induced by
10 V (level 3)
Radio-Frequency Fields
Performance criteria A
typical: 6V
IEC 61000-4-6
RS485: Bit rate
50 bit/s - 38.4 kbit/s
Level
typical: 6V
Environmental conditions Nominal operating temperature range:
Ethernet interface E1 and E2
-25C... 70C
EN 60068-2-1, -2-2, -2-14
Connector
RJ45
Type
IEEE 802.3, 10/100BaseT
Relative humidity
5 ... 95 %
EN 60068-2-30
(non condensing)
Current consumption for power supplied via RTU560 backplane
Ordering information
5 V DC
560CMU02 R0002
1080 mA
1KGT012600R0002
24 V DC
Communication Unit 560CMU02 - 1KGT 150 717 V003 1 | 3
ABB AG Power Systems Division P.O. Box 10 03 51 68128 Mannheim, Germany
Note: The specifications, data, design or other information contained in this document (the Brochure) - together: the Information - shall only be for information purposes and shall in no respect be binding. The Brochure does not claim to be exhaustive. Technical data in the Information are only approximate figures. We re-
www.abb.com/substationautomation
serve the right at any time to make technical changes or modify the contents of this document without prior notice. The user shall be solely responsible for the use of any application example or information described within this document. The described examples and solutions are examples only and do not represent any comprehensive or complete solution. The user shall determine at its sole discretion, or as the case may be, customize, program or add value to the ABB products including software by creating solutions for the end customer and to assess whether and to what extent the products are suitable and need to be adjusted or customized. This product is designed to be connected to and to communicate information and data via a network interface. It is the users sole responsibility to provide and continuously ensure a secure connection between the product and users or end customers network or any other network (as the case may be). The user shall establish and maintain any appropriate measures (such as but not limited to the installation of firewalls, application of authentication measures, encryption of data, installation of anti-virus programs, etc) to protect the product, the network, its system and the interface against any kind of security breaches, unauthorized access, interference, intrusion, leakage and/or theft of data or information. ABB AG is not liable for any damages and/or losses related to such security breaches, any unauthorized access, interference, intrusion, leakage and/or theft of data or information. ABB AG shall be under no warranty whatsoever whether express or implied and assumes no responsibility for the information contained in this document or for any errors that may appear in this document. ABB AG's liability under or in connection with this Brochure or the files included within the Brochure, irrespective of the legal ground towards any person or entity, to which the Brochure has been made available, in view of any damages including costs or losses shall be excluded. In particular ABB AG shall in no event be liable for any indirect, consequential or special damages, such as but not limited to loss of profit, loss of production, loss of revenue, loss of data, loss of use, loss of earnings, cost of capital or cost connected with an interruption of business or operation, third party claims. The exclusion of liability shall not apply in the case of intention or gross negligence. The present declaration shall be governed by and construed in accordance with the laws of Switzerland under exclusion of its conflict of laws rules and of the Vienna Convention on the International Sale of Goods (CISG). ABB AG reserves all rights in particular copyrights and other intellectual property rights. Any reproduction, disclosure to third parties or utilization of its contents in whole or in part - is not permitted without the prior written consent of ABB AG. Copyright ABB 2014 All rights reserved
4 | 1KGT 150 717 V003 1 - Communication Unit 560CMU02
