Scribd
Upload
420 views3 pages

Cisco Skills Integration: 1.6.1.3

Cisco chapter 1 completed skills integration.

Uploaded by

BrandsmaSj
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
420 views3 pages

Cisco Skills Integration: 1.6.1.3

Cisco chapter 1 completed skills integration.

Uploaded by

BrandsmaSj
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

Ch1 - Packet Tracer Skills Integration Instructions

Topology Diagram

Addressing Table
Device

Interface

IP Address

Subnet Mask

Default Gateway

Fa0/0

192.168.1.129

255.255.255.192

N/A

S0/0/0

192.168.1.225

255.255.255.252

N/A

S0/0/1

192.168.1.229

255.255.255.252

N/A

Fa0/0

192.168.1.1

255.255.255.128

N/A

S0/0/0

192.168.1.226

255.255.255.252

N/A

Fa0/0

192.168.1.193

255.255.255.224

N/A

S0/0/1

192.168.1.230

255.255.255.252

N/A

PC1

NIC

192.168.1.126

255.255.255.128

192.168.1.1

PC2

NIC

192.168.1.190

255.255.255.192

192.168.1.129

PC3

NIC

192.168.1.222

255.255.255.224

192.168.1.193

HQ

B1
B2

Objectives

Design and cument an addressing scheme based on requirements.

Select appropriate equipment and cable the devices.

Apply a basic configuration to the devices.

Verify full connectivity between all devices in the topology.

Identify layer 2 and layer 3 addresses used to switch packets.

All contents are Copyright 20072009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 1 of 3

CCNA Exploration
Routing Protocols and Concepts:
Introduction to Routing and Packet Forwarding

Ch1 - Packet Tracer Skills Integration Instructions

Task 1: Design and document an addressing scheme.


Step 1: Design an addressing scheme.
Based on the network requirements shown in the topology, design an appropriate addressing scheme.

Starting with the largest LAN, determine the size of each subnet you will need for the given host
requirement.

After the addresses have been determined for all the LAN subnets, assign the first available
address space to the WAN link between B1 and HQ.

Assign the second available address space to the WAN link between HQ and B2.

(Note: Remember that the interfaces of network devices are also host IP addresses and are included
in the above addressing requirements.)
Step 2: Document the addressing scheme.

Use the blank spaces on the topology to record the network addresses in dotted-decimal/slash
format.

Use the table provided in the printed instructions to document the IP addresses, subnet masks
and default gateway addresses.
For the LANs, assign the first IP address to the router interface. Assign the last IP
address to the PC
For the WAN links, assign the first IP address to HQ.

Task 2: Select equipment and cable devices.


Step 1: Select the necessary equipment.
Select the remaining devices you will need and add them to the working space inside Packet Tracer. Use
the labels as a guide as to where to place th2e devices.
Step 2: Finish cabling the devices.
Cable the networks according to the topology taking care that interfaces match your documentation in
Task 1.

Task 3: Apply a basic configuration.


Step 1: Configure the routers.
Using your documentation, configure the routers with basic configurations including addressing. Use
cisco as the line passwords and class as the secret password. Use 64000 as the clock rate.
Step 2: Configure the PCs.
Using your documentation, configure the PCs with an IP address, subnet mask, and default gateway.

Task 4: Test connectivity and examine the configuration.


Step 1: Test connectivity.
RIP routing has already been configured for you. Therefore, you should have end-to-end connectivity.

Can PC1 ping PC2? ___Yes_____

All contents are Copyright 20072009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 2 of 3

CCNA Exploration
Routing Protocols and Concepts:
Introduction to Routing and Packet Forwarding

Can PC1 ping PC3? ___Yes_____

Can PC3 ping PC2? ___Yes_____

Ch1 - Packet Tracer Skills Integration Instructions

Troubleshoot until pings are successful.


Step 2: Examine the configuration.
Use verification commands to make sure your configurations are complete.

Task 5: Identify layer 2 and layer 3 addresses used to switch packets.


Step 1: Create a simple PDU ping packet

Enter Simulation Mode.

Use the Add Simple PDU button to create a ping from PC1 to PC3.

Change Edit Filters so that only ICMP is simulated.

Step 2: Addresses at PC1


Record the addresses used by PC1 to send the ping packet to B1:
Layer 3 Source: 192.168.1.126_________________________________________
Layer 3 Destination: 192.168.1.222_________________________________________
Layer 2 Source: 0001.9713.0EDB _________________________________________
Layer 2 Destination: 0002.1669.a701 _________________________________________
Step 3: Addresses at B1
Record the addresses used by B1 to switch the ping packet to HQ:
Layer 3 Source: 192.168.1.126_________________________________________
Layer 3 Destination: 192.168.1.222_________________________________________
Layer 2 Source: none_________________________________________
Layer 2 Destination: 08xf_________________________________________
Step 4: Addresses at HQ
Record the addresses used by HQ to switch the ping packet to B2:
Layer 3 Source: 192.168.1.126_________________________________________
Layer 3 Destination: 192.168.1.222_________________________________________
Layer 2 Source: none_________________________________________
Layer 2 Destination: 08xf_________________________________________
Step 5: Addresses at B2
Record the addresses used by B2 to switch the ping packet to PC3:
Layer 3 Source: 192.168.1.126_________________________________________
Layer 3 Destination: 192.168.1.222_________________________________________
Layer 2 Source: 0001 64C5 8501_________________________________________
Layer 2 Destination: 000D BDBB E27C_________________________________________
All contents are Copyright 20072009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 3 of 3

You might also like