SMART DISTRIBUTION APPLICATIONS &THEIR

INTEGRATION IN A SMART GRID ENVIRONMENT

Presented By:
Bob Uluski
Electric Power Research Institute
July, 2011

Key Smart Distribution Applications

What are the major trends of the day?

What issues need to be resolved?
Where should the industry go from here?

Distribution Voltage Optimization

Major Trend: Many electrical utilities are implementing Conservation
Voltage Reduction for demand and energy reduction

ANSI standards have some

flexibility in the allowable
delivery voltage
Distribution utilities
typically have delivery
voltage in upper portion of
the range
Concept of CVR: Maintain
voltage delivered to the
customer in the lower
portion of the acceptable
range

CVR Benefits Achieved

CVR factor for voltage reduction ranges from 0.65 to 0.7
Reduction of electrical demand ranges from 1.5% to 2.1%
Cheap alternative to conventional generation
Reduction of total demand by 310 MW (eliminate need for
two peak shaving CTs)
No carbon or emission offsets needed

Reduction of energy consumption ranges from 1.3% - 2%

Near unity power factor
Provide demand response capabilities
Decrease sub/feeder overloading
Reduced High and Low voltage complaints
Improve Customer voltage quality (less flicker).
Increase customer end-use appliance life by 15%.
Lower Customer Bills $16.50/yr

Distribution Voltage Optimization

Key issues and challenges
CVR Factors for various
Substations

Major Issue: Not all feeders are created equal

from a CVR perspective Benefit varies with
load type and feeder characteristics

Effectiveness measured by CVR

factor:

27
25
23
21

CVR factor = %
change in load
% change in
voltage

19
17
15
13
11

Average of these results: CVFf = 1.2

CVRf usually ranges between 0.7 and
0.8
Need ability to determine
benefits in advance

9
7
5
3
1

0.0

2.0

4.0

6.0

Distribution Voltage Optimization

Key issues and challenges
Major Issue: Will the CVR benefit last long into the future? Or, will the benefits
diminish in just a few years?

Some emerging load characteristics dont favor CVR

Need better understanding of up and coming appliances to determine if CVR will
provide lasting effects

Distribution Voltage Optimization

Key issues and challenges
Major Issue: What general approach to CVR works best?

Standalone Voltage regulator and LTC controls with line

drop compensation set to end-of-line voltage for CVR
On-Site Voltage Regulator (OVR) for single location
voltage regulation
Rule-based DA control of capacitor banks and voltage
regulators for CVR with/without voltage measurement
feedback from end of line
Auto-Adaptive voltage regulation (e.g. PCS Utilidata
AdatiVolt, Cooper Power Systems IVVC)
Distribution model based Volt-VAR Optimization

Distribution Voltage Optimization

Key issues and challenges
Major Issue: What general approach to CVR works best?

Distribution Voltage Optimization

Major issue: What infrastructure improvements are needed to effectively
implement CVR? Are these infrastructure improvements economically justified

Feeder conditioning needed to flatten voltage profile to

maximize CVR benefits
Addition of fixed and switched capacitor banks
Feeder re-configuration
Feeder phase balancing
Reconductoring
Replacement of electromechanical volt-VAR controllers with
Intelligent Electronic Devices (IEDs)
Addition of two way communication facilities
Addition of end-of-line (EOL) metering

Distribution Voltage Optimization

Major issue: How can AMI assist with effective deployment of CVR? What
critical measurements are needed for effective CVR deployment?

Need to determine critical voltage measurements for CVR

Many utilities currently use AMI or bell weather meters for
voltage feedback
i.e. where are the lowest voltage points at any given time?
AMI appears to be an ideal source for providing voltage feedback

How many measurements are needed?

What locations should be monitored?
How often should measurements be taken?
Do natural fluctuations in individual measurements affect usability of AMI
data

Distribution Voltage Optimization

Where should industry go from here?
Need ability to predict CVR benefits
Excellent work going on at PNNL, NEETRAC, EPRI and other
organizations to model CVR behavior
Work being coordinated through IEEE volt-VAR task force

Must include distribution voltage optimization

(CVR) in distribution planning process
Impact on capacity planning process
Design necessary infrastructure improvements

Vendors and utilities alike need to gain practical

experience with the concept (demonstrations and
full-scale deployments)

Dynamic Volt-VAR Control

Major Trend: Growing need for dynamic voltage control due to
variable output from renewable energy resources.

Dynamic Volt-VAR Control

Major Trend: Growing need for dynamic voltage control due to
variable output from renewable energy resources.

Dynamic Volt/Var Control

Key issue: Need to deal with fluctuations associated with variable
power output to prevent customer complaints, excess wear and tear
on voltage regulators (LTCs), and other anomolies.
Solar PV inverters typically operate at unity power factor
Var control is possible in most applications
Inverters have inherent ability to control vars
No hardware change required
Firmware upgrade only
VA Headroom
Data mining of over 40,000 PV installations in CA
PV inverters typically sized greater than solar panel
20% margin or headroom available in inverters to provide var control
Some form of communication is needed
Vars could be controlled by utility via broadcast commands

Dynamic Volt/Var Control

Key issue: Need to deal with fluctuations associated with variable
power output to prevent customer complaints, excess wear and tear
on voltage regulators (LTCs), and other anomalies.
Utility-Defined Curve Shapes

Simple
Broadcast

Volt/Var
Mode 2 VAR
Support

VARs Generated

Volt/Var
Mode 1
Normal
Regulation

Capacitive

VARs Generated

Q1

Capacitive

Q2

System
Voltage

Q3

V4
V1

V2

V3

Inductive

Q4
Q1

Q2
V1
V2
Inductive

System
Voltage

Dynamic Volt/Var Control

Key issue: Need to deal with fluctuations associated with variable
power output to prevent customer complaints, excess wear and tear
on voltage regulators (LTCs), and other anomalies.

Feeder Medium Voltage Response

1.05

12 kV Voltage

20% PV

1.025

V (pu)

20% PV w/ volt-var control

0.975

0.95

Baseline No PV

0.925

0.9
0

12

Hour

16

20

Dynamic Volt/Var Control

Key issue: Restrictive Clause 4.1.1 in IEEE 1547-2003

The Distributed Energy Resource (DR) shall not actively regulate the voltage
at the Point of Common Connection (PCC). The DR shall not cause the Area
Electric Power System (EPS) service voltage at other Local EPSs to go outside
the requirements of ANSI C84.1-1995, Range A.

addresses the possible impacts of the DR:

Impact of DR operations on voltage-regulating devices, which may
create either a too low, or a too high voltage.
Voltage imbalance due to single-phase DR
Intermittent operations of DR, which may result in unacceptable
voltage fluctuations and excessive operations of voltage-regulating
devices in the Area EPS
Improper regulation during reverse power flow conditions, which may
result in either a too high, or a too low voltage

Dynamic Volt-VAR Control

Where should industry go from here?
Continue IEEE 1547.8 WG activities to develop Recommended
Practice for Establishing Methods and Procedures that Provide
Supplemental Support for Implementation Strategies For
Expanded Use of IEEE Standard 1547
Enhance standard communication protocols (e.g., DNP3) to
support broadcast commands to smart inverters.
Add support for smart inverter controls to DMS suite of
applications

Fault Location Isolation & Service Restoration (FLISR)

Major Trend: Many electrical utilities are implementing FLISR as a
means of implementing a self-healing grid

Nature of the Problem

When a permanent fault occurs, customers on healthy

sections of the feeder may experience a lengthy outage
FAULT
OCCURS

Customer
Reports
Outage

Field
Crews
On-Scene
Travel Time

5 10
minutes

15 30
minutes

Fault
Located

POWER RESTORED
TO CUSTOMERS ON
HEALTHY SECTIONS
OF FEEDER

Fault Investigation
& Patrol Time

Time to Perform
Manual Switching

15 20
minutes

10- 15
minutes

Feeder
Back to
Normal

Repair Time

45 75
minutes

FLISR provides the means to restore service to some

customers before field crews arrive on the scene

Normal Configuration

A Fault Occurs

Flow of Fault Current Triggers

Faulted Circuit Indicators (FCIs)

and trips again (lockout)

FLISR identifies faulted section by comparing FCIs

FLISR opens switches to isolate

the faulted feeder section

FLISR Triggers Upstream Restoration

Downstream restoration of blinking section

Compare load with available capacity

Downstream restoration of blinking section

Compare load with available capacity
Available Capacity
= 2 MW
Pre-fault load
= 1 MW

Capability exists, so
Available Capacity
= 2 MW
Pre-fault load
= 1 MW

FLISR closes switch to restore service

Via alternate supply line

Now FLISR checks for capacity to

Transfer last downstream section
Available Capacity =
1.5 MW
Pre-fault load
= 2 MW

In this case capacity does not exist so

downstream section is not restored
Available Capacity =
1.5 MW
Pre-fault load
= 2 MW

Major Issue: Lack of capacity

on backup supply circuits

FLISR: Key issues and challenges

Major Issue: Lack of capacity on backup supply circuits
Available Capacity =
2.5 MW
Pre-fault load
= 2 MW

Can offload red substation by transferring

load to another substation, applying
demand response, using CVR,
discharging energy storage, reduce
amount of fast charging, etc

These actions free enough capacity to

pick up last remaining section, so
Available Capacity =
2.5 MW
Pre-fault load
= 2 MW

Can offload red substation by transferring

load to another substation, applying
demand response, using CVR,
discharging energy storage, reduce
amount of fast charging, etc

Can pick up the last downstream section

Can offload red substation by transferring

load to another substation, applying
demand response, using CVR,
discharging energy storage, reduce
amount of fast charging, etc

Time Line Without and With FLISR

Fault
Occurs

member
Reports
Outage
Fault Investigation
& Patrol Time

Travel Time

Without
FLISR
5 10
minutes

member
Reports
Outage

1 to 5
minutes

15 30
minutes

POWER RESTORED
ON
HEALTHY SECTIONS
OF FEEDER

Feeder
Back to
Normal

Field
Crews
On-Scene
Patrol
Time

5 - 10
minutes

Repair Time

1-4
Hours

Repair Time

1-4
Hours

10 - 15
minutes

45 75
minutes

Travel Time

5 10
minutes

Time to Perform
Manual Switching

15 20
minutes

15 30
minutes

POWER RESTORED
ON
HEALTHY SECTIONS
OF FEEDER
FAULT
OCCURS

Feeder
Back to
Normal

Fault
Located

With
FLISR

FLISR with large distributed generation present

Major Issue: Impact of high DG presence on FLISR Operation

FLISR with large distributed generation present

Major Issue: Impact of high DG presence on FLISR Operation

Same fault occurs

Flow of Fault Current Triggers

Faulted Circuit Indicators (FCIs)

Circuit breaker opens

FLISR analyzes FCIs incorrectly identifies

faulted segment

Need directional FCI or short

circuit model to avoid this
situation

Fault Location Isolation & Service Restoration

Where should industry go from here?
Incorporate energy storage and possible microgrid
in FLISR operation
Develop planning & design criteria for effective
FLISR implementation
Availability of backup sources with sufficient capacity
Protection system that adapts to feeder reconfiguration
Design necessary infrastructure improvements

Optimal Network Reconfiguration

Goal: Identify changes in feeder
configuration that would improve overall
distribution feeder performance and
reliability
optimize topology for steady state
operations

Selectable Operating Objective

Minimal power and energy losses

Maximum reliability
Best load balance
Best voltage profiles
Weighted combination of the above

Optimal Network Reconfiguration

Goal: Identify changes in feeder
configuration that would improve overall
distribution feeder performance and
reliability
optimize topology for steady state
operations

Selectable Operating Objective

Minimal power and energy losses

Maximum reliability
Best load balance
Best voltage profiles
Weighted combination of the above
Load
Transfer
Occurs

Conclusions

Advanced distribution applications will play a growing role in managing

distribution system operation for improved efficiency, reliability, and performance

Utilities must have the necessary skills to deal with these new systems:

New planning tools and capabilities are needed for smart distribution systems

Training/certification of operators
New procedures and business processes
Maintenance of hi tech systems
Growing engineering support in the DSO

Account for advanced control capabilities,

Model impact of DER
Real and reactive power forecasting
Make sure software supplier vendors are in sync with the needs of planning engineers

AMI will certainly play a key role in maximizing the benefits

improved accuracy and lower operating margins
Still some significant issues that need to be addressed such as data throughput and
security

Questions and Discussion

Bob Uluski
Electric Power Research Institute
102 Stevens Drive
Fort Washington, PA 19034
[email protected]
(215) 317-9105