Cititor Stand Alone Interior Sebury Cartele Proximitate Cod Controller

K3
K4
Digital Keypad
www.sebury.com.cn
Use s M anual
K3/K4 user s manual
Contents
Introduction
Introduction
Specifications
Intramural Interface Circuit
Mounting
Wiring
Power UP
Engineer Programming Mode
Changing Master & User Codes
User Operation Mode
Setting Door Relay Strike time
Setting Alarm Signal Output Time
Set Door Open Detection Time
9
9
Resetting to Factory default setting
10
Changing User Password Code
10
Technical Specifications
11
Package Listing
11
Before the installation carefully read the manual
Store 1000 prox cards and user 4 digit codes. Each 4 digit code has
10,000 possible combinations. The unit has one relay with 2 Amp
contacts.
Delete User Card OR Cards
Setting Security Arrangement
The K3/K4 uses the latest microprocessor technology to operate

door strikes and security systems that require a momentary (timed)
or latching dry contact closure.
All programming is done through the keypad. Codes and operating
parameters are stored within the microprocessor and can not be
lost due to power failure.
Specifications
Programmable Functions
Relay latching or momentary
Relay activate independently or together
Change Codes 1 master, 1000 users & prox cards
Door open detection
Programmable Timers
Door relay time 00-99 seconds
Door open detection 00-99 seconds
Alarm time 00-99 minutes
Wiring Connections
Electric lock
www.sebury.com.cn
K3/K4 user s manual
External Push Switch

Magnetic Contacts
Alarm
Keypad:
12 keys
Programming memory:
Non volatile Eeprom memory
IMPORTANT INFORAMTION
There are no user serviceable parts contained within the K3
access control keypad.
K3/K4 user s manual
Intramural Interface Circuit

1. Alarm output interface (See Figure 1)
ALARM
R
Figure 1
2K
GND
2. Electric lock interface (See Figure 2)
NC
If holes are to be drilled before mounting onto a wall, check for

hidden cables and/or pipes before drilling. Use safety goggles
when drilling or hammering in cable clips.
Every effort has been made to provide accurate information,
however slight variations can occur. We also reserve the right to
make changes for product improvement at any time
NO
Figure 2
RELAY
COM
Mounting
NOTE
PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE
ATTEMPTING TO INSTALL THE K3/K4
www.sebury.com.cn
1. Attach the rear plate to a single or double gang electrical box or

secure to the wall firmly with at least three flat head screws.
2. When wiring has been completed, attach the front cover to the
rear plate.
www.sebury.com.cn
K3/K4 user s manual
K3/K4 user s manual
Wiring
The front cover can be permanently secured by using the short

screw supplied K3/K4
Unplug the cable harness and connect the necessary cables,

(See Figure 5). showed as Figure 6
for special power Supply
connections, this power will make controller work stablly .

Tape any wires that are unused. Plug the cable harness , (See
Figure 5) Attach the front cover, (See Figure 3).
K4
K3
Figure 3
Terminal Wire Connector 1 Function
NC
COM
NO
GND
12V
D _ IN
OPEN
ALARM
BELL1
BELL2
J1
SW13
J3
1 2 3
RST
K3
4
www.sebury.com.cn
Printed Circuit Board

Figure 4
K4
10
9
8
7
6
5
4
3
2
1
Bell2
Bell1
ALARM
OPEN
D_IN
12V
GND
NO
COM
NC
Green
White
Grey
Yellow
Brown
Red
Black
Blue
Purple
Orange
Not Connect
Not Connect
Alarm
ToDoor Remote ControlButton Then Negative
To Door Contact Then To Door In
(+) 12Vdc Positive Regulated Power Input
(-) Negative Regulated Power Input
Door Strike Relay N/O
Door Strike Relay COM
Door Strike Relay N/C
Warning!
1N4007 is necessory ,otherwise the controller doesn't work stablly.
GND
Do not plug adapter our transformer into mains until all wiring has
been completed and the front cover secured.
www.sebury.com.cn
K3/K4 user s manual
K3/K4 user s manual
BELL2
BELL1
ALARM
OPEN
D_IN
+12V
GND
NO
COM
NC
Power Up
Power Supply
common power supply connection
Green
White
Grey
Yellow
Brown
Red
Black
Blue
Purple
Orange
GND
+12V
Annunciator
After all wiring is complete and the unit face plate is attached to the
back plate, apply 12Vdc power to the unit. READY LED (the red
LED) lighting on, ACCEPT LED(the yellow LED) flashing at K3.
READY LED(the red LED) lighting on, ACCEPT LED(the red LED)
flashing at K4.
Door Status Inspector
Engineer Programming Mode

Electric Rim Lock
To enter programming mode

Press: * 9999 # within 5 seconds, Ready(the green LED) and
Accept LED illuminated, Open LED flashing.
Electric Door Bolt
Figure 5
Note
Press: # to save changes and exit engineer programming, when all
programming has been completed otherwise changes will not be saved.
Special Power Supply
special power connection
www.sebury.com.cn
Door Status Inspector
GND2
+12V/3A
Figure 6
Annunciator
GND1
Green
White
Grey
Yellow
Brown
Red
Black
Blue
Purple
Orange
+12V/1A
BELL2
BELL1
ALARM
OPEN
D_IN
+12V
GND
NO
COM
NC
Changing Master & User Codes

In engineer programming mode:
To change Master code
Press: 0 new master code # re-enter new master code #
Upon acceptance Open LED illuminates and stops flashing. Press
# after changing the master code, otherwise unit will disregard
the new code and revert back to the factory default code.
Electric Rim Lock

Electric Door Bolt
Note: the master code must be 4-8 digit number.
Adding User Codes & Cards

www.sebury.com.cn
K3/K4 user s manual
K3/K4 user s manual
To Add User cards & codes

Press: 1 read card user identification #
Note: the user identification must be 3 digit number, if adding more
than 1 card, read the next card after inputting the 3 digit code for
the previous card, when you have finished adding all cards press
the # key. 1st card must be 000 up to 999.
Then the K3/K4 control station added a user card it was auto added
a user code with 1234.
through the relay if used as normally opened or 2 ampere if

normally closed. The door relay time can be set from 0 seconds to
a maximum of 99 seconds. The factory default setting is 6 seconds
and can be changed through the keypad.
Press:
new time from 00-99 seconds
Setting Alarm Signal Output Time

Press:
5 new time from 00-99 minutes
Delete User Card or Cards

There are 3 options to delete a user card or cards, in engineering mode.
A.) Press:
b.) Press:
2 read card
0 0 00
c.) Press:
# to delete all user cards

# to delete individual user card
user identification number
to delete individual
user card
Setting Door Open Detection

Press:
6 00
to disable this function (factory setting)
Press:
6 01
to enable this function.
In order for this feature to work, door contacts must be connected.

There are 2 programming functions that work together in this mode.
User Operation Mode
There are 3 different options for user operation mode, card only, card
and password, valid code. The optioned used is common to all users.
Press:
00
valid card only
Press:
01
valid card and password
Press:
02
valid card or passwor
a.)If door not closed after opening, keypad buzzer sounds.

B.)If door forced open, keypad buzzer sounds and sends alarm
signal.
Setting Security Arrangement

There are two levels of keypad security available for the K3/K4.
Setting Door Relay Strike Time
Press:
The door relay output can be operated as either normally opened
enter 4 wrong passwords in succession, the keypad is locked for
or normally closed, a maximum current of 3 ampere can pass
10 minutes.
www.sebury.com.cn
01
to read 10 invalid cards or valid cards, then
www.sebury.com.cn
K3/K4 user s manual
Press:
K3/K4 user s manual
02
alarm signal.
To disable this feature:
Press: 7
00
Technical Specification
to read 10 invalid cards or valid cards, then
enter 4 wrong passwords in succession, the keypad activates and
factory default setting.
Resetting To Factory Default Setting

To revert all settings to the factory default values then the Non
Volatile Memory (Eeprom) must be reset.
Reset Non Volatile Memory by switching of the power and placing
the jumper connector onto the pins 1 & 2 as per figure 4. After
switching power on remove jumper, the K3/K4 will give a beep and
is now reset to factory default values.
DC Supply Voltage
Current Consumption
Door Relay
Alarm output load
Tamper Protection
Codes
Low voltage input 12 10% Vdc unregulated

100mA @ quiescent
2Amp 12Vdc
150mA pull current
Negative loop, normally closed
1 Master, 1000 cards and 1000 codes .
K3(12 keys, 3 LED status indicators)
Keypad
K4(12 keys, 2 LED status indicators)
EM or EM compatible
Card Types
Induction Distance
5-10cm
Electric lock
Remote door control
Wiring Connections
Door open detection
External Alarm
Memory
Non volatile Eeprom memory
Operating Temperature -20 to 60
Keypad Housing
ABS+PC
K3(90mm
60mm
27mm)
Dimensions
K4(120mm
50mm
27mm)
Weight
100g
Changing User Password Code

Package Listing
The factory default setting for each user password code 1234, this can
be modified so that each user has a unique individual 4 digit code.
Press: * read user card user passoword
# re-enter new password #
new password
Using Password Code to release the door

Press: user passoword #
10
www.sebury.com.cn
Name
Digital Keypad
User Manual
Cable
Model no.
K3/K4
Security Screws
3mm
Screwdriver
Pastern Stopper
Self Tapping Screws
Diode
10Pin
12mm
6mm 27 mm
3.5mm 27 mm
1N4007
Quantity
1
1
1
1
1
4
4
1
Remark
Used for front case

and back case
(spare)
Used for fixing
Used for fixing
Used for lock
www.sebury.com.cn
11

Cititor Stand Alone Interior Sebury Cartele Proximitate Cod Controller

Uploaded by

Copyright:

Available Formats

Cititor Stand Alone Interior Sebury Cartele Proximitate Cod Controller

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cititor Stand Alone Interior Sebury Cartele Proximitate Cod Controller

Uploaded by

Copyright:

Available Formats

K3

K3/K4 user s manual

Intramural Interface Circuit

Engineer Programming Mode

Changing Master & User Codes

User Operation Mode

Setting Door Relay Strike time

Setting Alarm Signal Output Time

Set Door Open Detection Time

Resetting to Factory default setting

Changing User Password Code

Before the installation carefully read the manual

Delete User Card OR Cards

Setting Security Arrangement

The K3/K4 uses the latest microprocessor technology to operate

K3/K4 user s manual

External Push Switch

K3/K4 user s manual

Intramural Interface Circuit

2. Electric lock interface (See Figure 2)

If holes are to be drilled before mounting onto a wall, check for

1. Attach the rear plate to a single or double gang electrical box or

K3/K4 user s manual

K3/K4 user s manual

The front cover can be permanently secured by using the short

Unplug the cable harness and connect the necessary cables,

for special power Supply

connections, this power will make controller work stablly .

Terminal Wire Connector 1 Function

Printed Circuit Board

K3/K4 user s manual

K3/K4 user s manual

common power supply connection

External Push Switch

Door Status Inspector

Engineer Programming Mode

To enter programming mode

Electric Door Bolt

special power connection

Door Status Inspector

External Push Switch

Changing Master & User Codes

Electric Rim Lock

Note: the master code must be 4-8 digit number.

Adding User Codes & Cards

K3/K4 user s manual

K3/K4 user s manual

To Add User cards & codes

through the relay if used as normally opened or 2 ampere if

new time from 00-99 seconds

Setting Alarm Signal Output Time

5 new time from 00-99 minutes

Delete User Card or Cards

# to delete all user cards

user identification number

Setting Door Open Detection

to disable this function (factory setting)

to enable this function.