TM 5 3805 261 23 2 PDF

TM 5-3805-261-23-2
TECHNICAL MANUAL
FIELD MAINTENANCE MANUAL

(Includes Unit and Direct Support Maintenance)
FOR
GRADER, ROAD, MOTORIZED, DIESEL ENGINE DRIVEN (DED), HEAVY,

COMMERCIAL CONSTRUCTION EQUIPMENT (CCE)
(NSN 3805-01-150-4795) CATERPILLAR MODEL 130G (EIC: EHF)
TYPE I, NONSECTIONALIZED
(NSN 3805-01-126-7894) CATERPILLAR MODEL 130GNS (EIC: EHN)
(NSN 3805-01-252-0128) CATERPILLAR MODEL 130GNSCE (EIC: EJJ)
TYPE II, SECTIONALIZED

(NSN 3805-01-126-7895) CATERPILLAR MODEL 130GS (EIC: EHP)
(NSN 3805-01-251-8252) CATERPILLAR MODEL 130GSCE (EIC: EJH)
SUPERSEDURE NOTICE - This manual supersedes TM 5-3805-261-20, dated 30 April 1992; TM 53805-261-34, dated 25 April 1989, including all changes; TM 5-3805-259-24, dated 16 April 1988; and
TM 5-3805-263-14&P-1,-2,-3, and -4, dated 14 April 1989.
.
DISTRIBUTION STATEMENT A - Approved for public release; distribution is unlimited.
HEADQUARTERS, DEPARTMENT OF THE ARMY

FEBRUARY 2007
only Left Blank.
This page is blank.
TM 5-3805-261-23-2
WARNING SUMMARY
This warning summary contains general safety warnings and hazardous materials warnings that must be understood and
applied during operation and maintenance of this equipment. Failure to observe these precautions could result in serious injury
or death to personnel. Also included are explanations of safety and hazardous materials icons used within the technical manual.
BIOLOGICAL - abstract symbol bug shows that a material may contain bacteria or viruses that
present a danger to life or health.
CHEMICAL - drops of liquid on hand shows that the material will cause burns or irritation to
human skin or tissue.
EAR PROTECTION - Headphones over ears show that noise level will harm ears.
ELECTRICAL - electrical wire to arm with electricity symbol running through human body
shows that shock hazard is present.
EYE PROTECTION - person with goggles shows that the material will injure the eyes.
FIRE - flame shows that a material may ignite and cause burns.
FLYING PARTICLES - arrows bouncing off face with face shield shows that particles flying
through the air will harm face.
HEAVY PARTS - hand with heavy object on top shows that heavy parts can crush and harm.
TM 5-3805-261-23-2
HEAVY OBJECT - human figure stooping over heavy object shows physical injury potential
from improper lifting technique.
HEAVY PARTS - heavy object on human figure shows that heavy parts present a danger to life or
limb.
HOT AREA - hand over object radiating heat shows that part is hot and can burn.
HYDRAULIC FLUID PRESSURE - hydraulic fluid spraying human figure shows that fluid
escaping under great pressure can cause injury or death to personnel.
POISON - skull and crossbones shows material is poisonous or is a danger to life.
RADIOACTIVE - identifies a material that emits radioactive energy and can injure human tissue
or organs.
SLICK FLOOR - wavy line on floor with legs prone shows that slick floor presents a danger from
falling.
VAPOR - human figure in a cloud shows that material vapors present a danger to life or health.
TM 5-3805-261-23-2
FOR INFORMATION ON FIRST AID, REFER TO FM 4-25.11.
WARNING
CARBON MONOXIDE (EXHAUST GASES) CAN KILL!
Carbon monoxide is a colorless, odorless, deadly poison which, when breathed, deprives the body of oxygen
and causes suffocation. Exposure to air containing carbon monoxide produces symptoms of headache, dizziness, loss of muscular control, apparent drowsiness, and coma. Permanent brain damage or death can result
from severe exposure.
Carbon monoxide occurs in exhaust fumes of internal combustion engines. Carbon monoxide can become dangerously concentrated under conditions of inadequate ventilation. The following precautions must be observed
to ensure safety of personnel when engine is operated.
1.
DO NOT operate engine in enclosed areas.
2.
DO NOT idle engine without adequate ventilation.
3.
DO NOT drive machine with inspection plates or cover plates removed.
4.
BE ALERT for exhaust poisoning symptoms. They are:

Headache
Dizziness
Sleepiness
Loss of muscular control
5.
If you see another person with exhaust poisoning symptoms:

Remove person from area.
Expose to fresh air.
Keep person warm.
Do not permit physical exercise.
Administer Cardiopulmonary Resuscitation (CPR), if necessary.
Notify a medic.
6.
BE AWARE. The field protective mask for Nuclear, Biological, and Chemical (NBC) protection will not protect you
from carbon monoxide poisoning.
The Best Defense Against Carbon Monoxide Poisoning Is Good Ventilation!

c
TM 5-3805-261-23-2
WARNING
BATTERIES
To avoid injury, eye protection and acid-resistant gloves must be worn when working around batteries. Do not
smoke, use open flame, make sparks, or create other ignition sources around batteries. If a battery is giving off
gases, it can explode and cause injury to personnel. Remove all jewelry such as rings, ID tags, watches, and
bracelets. If jewelry or a tool contacts a battery terminal, a direct short will cause instant heating, damage to
equipment, and injury to personnel.
Sulfuric acid contained in batteries can cause serious burns. If battery corrosion or electrolyte makes contact
with skin, eyes or clothing, take immediate action to stop the corrosive burning effects. Failure to follow these
procedures may cause injury or death to personnel.
a.
Eyes. Flush with cold water for no less than 15 minutes and seek medical attention immediately.
b.
Skin. Flush with large amounts of cold water until all acid is removed. Seek medical attention as required.
c.
Internal. If corrosion or electrolyte is ingested, drink large amounts of water or milk. Follow with milk of magnesia,
beaten egg or vegetable oil. Seek medical attention immediately.
d.
Clothing/Equipment. Wash area with large amounts of cold water. Neutralize acid with baking soda or household
ammonia
WARNING
COMPRESSED AIR
Particles blown by compressed air are hazardous. DO NOT exceed 15 psi (103 kPa) nozzle pressure when
drying parts with compressed air. Use a maximum of 30 psi (207 kPa) when cleaning components. DO NOT
direct compressed air against human skin. Failure to follow this warning may result in injury or death. Make
sure air stream is directed away from user and other personnel in the area. To prevent injury, user must wear
protective goggles or face shield.
WARNING
ETHER COLD START SYSTEM
Ether fuel is extremely flammable and toxic. DO NOT smoke and make sure you are in a well-ventilated
area away from heat, open flames, or sparks. Wear eye protection. Avoid contact with skin and eyes and
avoid breathing ether fumes. If fluid enters or fumes irritate the eyes, wash immediately with large quantities
of clean water for 15 minutes. Seek medical attention immediately if ether is inhaled or causes eye irritation.
Failure to follow this warning may cause injury or death to personnel.
d
TM 5-3805-261-23-2
WARNING
FUEL HANDLING
DO NOT smoke or permit any open flame in area of machine while you are servicing fuel system. Be sure hose
nozzle is grounded against filler tube during refueling to prevent static electricity. Failure to follow this warning may cause injury to personnel or damage to equipment.
DO NOT perform fuel system checks, inspections, or maintenance while smoking or near fire, flames or
sparks. Fuel may ignite, causing injury or death to personnel or damage to equipment.
Operating personnel must wear fuel-resistant gloves when handling fuels. If exposed to fuel, promptly wash
exposed skin and change fuel-soaked clothing. Failure to follow this warning may cause injury to personnel.
WARNING
HAZARDOUS WASTE DISPOSAL
When servicing this machine, performing maintenance, or disposing of materials such as engine coolant,
hydraulic fluid, lubricants, battery acids or batteries, and CARC paint, consult your unit/local hazardous
waste disposal center or safety office for local regulatory guidance. If further information is needed, please
contact The Army Environmental Hotline at 1-800-872-3845.
WARNING
HEARING PROTECTION
Your hearing can be PERMANENTLY DAMAGED if you are exposed to constant high noise levels of 85 dB or
greater. Hearing protection is required when operating machine or when working on machine while it is operating.
Failure to wear hearing protection may cause hearing loss.
WARNING
HEAVY PARTS--LESS THAN 40 LB (18 KG)
Use extreme caution when handling heavy parts. Provide adequate support and use assistance during procedure. Failure to follow this warning may cause injury to personnel.
WARNING
HEAVY PARTS--40 LB (18 KG) OR MORE
Use extreme caution when handling heavy parts. Provide adequate support and use assistance during procedure. Ensure that any lifting device used is in good condition and of suitable load capacity. Keep clear of
heavy parts supported only by lifting device. Failure to follow this warning may cause injury or death to personnel.
e
TM 5-3805-261-23-2
WARNING
HYDRAULIC SYSTEM
DO NOT disconnect or remove any hydraulic system line or fitting unless engine is shut down and hydraulic
system pressure has been relieved. Tighten all connections before applying pressure. Escaping hydraulic fluid
under pressure can penetrate the skin, causing injury to personnel.
At operating temperature, hydraulic oil is hot. Allow hydraulic oil to cool before disconnecting any hydraulic
lines. Failure to follow this warning may cause injury to personnel.
WARNING
MACHINE OPERATION
Use caution and maintain three-point contact at all times when mounting or dismounting machine. Do NOT use
steering wheel as a handhold. Failure to follow this warning may cause injury or death to personnel.
BE ALERT for personnel in the area while operating machine. Always check to ensure area is clear of personnel and obstructions before moving. Failure to follow this warning may cause injury or death to personnel.
Use of seat belt while operating machine is mandatory. Fasten belt BEFORE operating machine. Trying to fasten belt during operation creates a hazardous condition. Failure to follow this warning may cause injury or
death to personnel.
DO NOT allow riders on machine. Failure to follow this warning may cause injury or death to personnel.
NEVER leave operator compartment without applying parking brake. Failure to follow this warning may cause
injury or death to personnel.
DO NOT use parking/emergency brake to stop a moving machine under usual conditions. Only if service
brakes fail, apply parking/emergency brake. Failure to follow this warning may cause injury to personnel or
damage to equipment.
Never use starting fluid or spray to aid in starting the engine, other than the on-board ether cold start system.
Failure to follow this warning may cause injury or death to personnel or damage to equipment.
Always use a ground guide when driving machine up or down ramps in preparation for highway or marine
transport. Failure to use a ground guide may cause injury or death to personnel or damage to equipment.
TM 5-3805-261-23-2
WARNING
NBC EXPOSURE
If NBC exposure is suspected, personnel wearing protective equipment must handle all air cleaner media. Consult your NBC Officer or NBC NCO for appropriate handling or disposal procedures.
Refer to FM 3-11.3, Chemical and Biological Contamination Avoidance, FM 3-11.5, NMC Decontamination,
FM 3-3-1, Nuclear Contamination Avoidance.
NBC contaminated filters must be handled using adequate precautions and must be disposed of by trained personnel.
Failure to follow these warnings may cause illness or death to personnel.
WARNING
IF NBC EXPOSURE IS SUSPECTED ALL AIR
FILTER MEDIA WILL BE HANDLED BY PERSONNEL WEARING FULL NBC PROTECTIVE
EQUIPMENT.
SEE
OPERATOR/
MAINTENANCE MANUAL.
7690-01-114-3702
To order this NBC decal use:

National Stock Number (NSN) - 7690-01-114-3702
Part Number (PN) - 12296626
Commercial and Government Entity Code (CAGEC) - 19207
WARNING
PRESSURIZED AIR
DO NOT disconnect any air system lines or fittings unless engine is shut down and air system pressure is
relieved. Failure to follow this warning may cause injury to personnel.
Always wear eye protection when disconnecting air lines. Residual air will be expelled. Failure to follow this
warning may cause eye injury.
TM 5-3805-261-23-2
WARNING
PRESSURIZED COOLING SYSTEM
DO NOT service cooling system unless engine has been allowed to cool down. This is a pressurized cooling
system and escaping steam or hot coolant may cause serious burns.
DO NOT remove cooling system radiator cap when engine is hot. Allow engine to cool down. Loosen cap to
first stop and let any pressure out of cooling system, then remove cap. Failure to follow this warning may cause
serious burns.
Wear effective eye, glove, and skin protection when handling coolants. Failure to do so may cause injury to
personnel.
WARNING
SLAVE STARTING
When slave starting machine:
Use NATO slave cable that does NOT have loose or missing insulation.
DO NOT proceed if suitable cable is not available.
DO NOT use civilian-type jumper cables.
DO NOT allow disabled and booster machines to come in contact with each other at any time during slave
starting.
Failure to follow this warning may cause injury or death to personnel.
WARNING
SOLVENT CLEANING COMPOUND
Solvent cleaning compound MIL-PRF-680 Type III is an environmentally compliant and low toxic material.
However, it may be irritating to the eyes and skin. Use protective gloves and goggles. Use in well-ventilated
areas. Keep away from open flames and other sources of ignition. Failure to do so may cause injury or death
to personnel.
WARNING
TIRES
Operating machine with underinflated or defective tire may lead to tire failure and loss of traction or control.
Failure to follow this warning may cause injury or death to personnel or damage to equipment.
Use a self-inflating chuck and stand at tread side of tire at maximum distance allowed by inflation hose. Failure
to do so may cause injury or death to personnel.
TM 5-3805-261-23-2
WARNING
WORK SAFETY
Lifting cables, chains, hooks, and slings used for lifting machine must be in good condition and of suitable
capacity. Failure to follow this warning may cause injury or death to personnel or damage to equipment.
Improper use of lifting equipment and improper attachment of cables to machine may cause injury to personnel
or damage to equipment. Observe all standard rules of safety.
Hitch and steering movement can reduce clearances suddenly and cause injury to personnel. Always stop
engine BEFORE working in area of hitch link.
Ensure locking pin is installed before working on hitch area (TM 5-3805-261-10). Failure to follow this warning may cause injury to personnel.
Configuration changes to blade cutting edge should NEVER be attempted without first securing the blade by
blocking it so that it is firmly supported. Failure to follow this warning may cause injury to personnel.
If machine is parked indoors, DO NOT run engine unless exhaust fumes are vented to the outside. Failure to
follow this warning may cause injury or death to personnel due to carbon monoxide poisoning.
Lubricating/hydraulic oils, engine coolant, fuel, and other fluids used in the performance of maintenance can
be very slippery. Immediately wipe up any spills. Failure to follow this warning may cause injury to personnel.
i/(J Blank)
TM 5-3805-261-23-2
LIST OF EFFECTIVE PAGES/WORK PACKAGES
Date of issue for original manual is:

Original 28 February 2007
TOTAL NUMBER OF PAGES FOR FRONT AND REAR MATTER IS 19 AND TOTAL NUMBER OF WORK PACKAGES IS 85 CONSISTING OF THE FOLLOWING:
Page/WP
*Change
No.
No.
Cover/(Back Blank)
a to h
A/(B Blank)
i to vi
WP 00267 00 to WP 0352 00
Index-1 to Index-6
Authentication Page
DA Form 2028 Sample
DA Form 2028
Metric Convsersion Chart
Back Cover
* Zero in this column indicates an original page or work package.

A/(B Blank)
TM 5-3805-261-23-2
TECHNICAL MANUAL
TM 5-3805-261-23-2
HEADQUARTERS
DEPARTMENT OF THE ARMY
Washington, D.C., 28 February 2007
TECHNICAL MANUAL
FIELD MAINTENANCE MANUAL
(Includes Unit and Direct Support Maintenance)
FOR
GRADER, ROAD MOTORIZED, DIESEL ENGINE DRIVEN (DED),
HEAVY, COMMERCIAL CONSTRUCTION EQUIPMENT (CCE)
(NSN 3805-01-150-4795) CATERPILLAR MODEL 130G
TYPE I, NONSECTIONALIZED
(NSN 3805-01-126-7894) CATERPILLAR MODEL 130GNS
(NSN 3805-01-252-0128) CATERPILLAR MODEL 130GNSCE
TYPE II, SECTIONALIZED
(NSN 3805-01-126-7895) CATERPILLAR MODEL 130GS
(NSN 3805-01-251-8252) CATERPILLAR MODEL 130GSCE
REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS
You can help improve this publication. If you find any mistakes or if you know of a way to improve the procedures,
please let us know. Submit your DA Form 2028 (Recommended Changes to Equipment Technical Publications),
through the Internet, on the Army Electronic Product Support (AEPS) website. The Internet address is https://
aeps.ria.army.mil/. The DA Form 2028 is located under the Public Applications section in the AEPS Public Home
Page. Fill out the form and click on SUBMIT. Using this form on the AEPS will enable us to respond quicker to your
comments and better manage the DA Form 2028 program. You may also mail, fax or e-mail your letter or DA Form
2028 direct to: AMSTA-LC-LMIT/TECH PUBS, TACOM-RI, 1 Rock Island Arsenal, Rock Island, IL 61299-7630.
The e-mail address is: [email protected]. The fax number is DSN 793-0726 or
Commerical (309) 782-0726.
SUPERSEDURE NOTICE - This manual supersedes TM 5-3805-261-20, dated 30 April 1992; TM 53805-261-34, dated 25 April 1989, including all changes; TM5-3805-259-24, dated 16 April 1988; and
TM 5-3805-263-14&P-1, -2, -3, and -4, dated 14 April 1989.
.
DISTRIBUTION STATEMENT A - Approved for public release; distribution is unlimited.
TM 5-3805-261-23-2
Table of Contents
Page
Number
VOLUME II
CHAPTER 4 DIRECT SUPPORT FIELD MAINTENANCE INSTRUCTIONS
Engine
WP 0267 00
WP 0268 00
WP 0269 00
WP 0270 00
WP 0271 00
WP 0272 00
WP 0273 00
WP 0274 00
WP 0275 00
WP 0276 00
WP 0277 00
Engine Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Mounting and Trunnion Replacement . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Front Covers Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Block Head Assembly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . .
Hub Driver Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flywheel and Flywheel Housing Replacement . . . . . . . . . . . . . . . . . . . . . . . . .
Rocker Arm Assembly Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valves Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pan and Oil Pan Plates Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump And Lines Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0267 00-1
0268 00-1
0269 00-1
0270 00-1
0271 00-1
0272 00-1
0273 00-1
0274 00-1
0275 00-1
0276 00-1
0277 00-1
Fuel System
WP 0278 00
WP 0279 00
WP 0280 00
WP 0281 00
WP 0282 00
WP 0283 00
Fuel Injection Nozzles Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278 00-1

Fuel Injection Pump Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0279 00-1
Fuel Injection Pump Mounting Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . 0280 00-1
Fuel Transfer Pump Maintenance (Models 130G, 130GSCE, and 130GNSCE) 0281 00-1
Governor Controls Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0282 00-1
Turbocharger Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0283 00-1
Electrical Ssytem
WP 0284 00
WP 0285 00
WP 0286 00
WP 0287 00
WP 0288 00
WP 0289 00
WP 0290 00
WP 0291 00
WP 0292 00
WP 0293 00
Electronic Monitoring System (EMS) Panel Repair . . . . . . . . . . . . . . . . . . . . .

Rear Signal Light and Backup Alarm Wiring Harness Replacement . . . . . . . .
Main Wiring Harness Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Blackout Light Wiring Harness Replacement . . . . . . . . . . . . . . . . . . . . .
Front Blackout Light Wiring Harness Replacement . . . . . . . . . . . . . . . . . . . . .
Rear Blackout Light Wiring Harness Replacement . . . . . . . . . . . . . . . . . . . . .
Supplemental Steering Main Wiring Harness Replacement . . . . . . . . . . . . . . .
Electronic Monitoring System (EMS) Main Wiring Harness Replacement . . .
Cab Main Wiring Harness Replacement (CCE Machine). . . . . . . . . . . . . . . . .
Rear Wiper Wiring Harness Replacement (CCE Machine) . . . . . . . . . . . . . . .
0284 00-1
0285 00-1
0286 00-1
0287 00-1
0288 00-1
0289 00-1
0290 00-1
0291 00-1
0292 00-1
0293 00-1
Transmission, Adapter, and Differential Replacement . . . . . . . . . . . . . . . . . . .

Engine-to-Transmission Adapter Replacement. . . . . . . . . . . . . . . . . . . . . . . . .
Transmission Control Relief Valve Maintenance . . . . . . . . . . . . . . . . . . . . . . .
Transmission Oil Pump Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission Oil Cooler Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission Oil Filler and Oil Level Gauge Replacement . . . . . . . . . . . . . . .
0294 00-1
0295 00-1
0296 00-1
0297 00-1
0298 00-1
0299 00-1
Transmission
WP 0294 00
WP 0295 00
WP 0296 00
WP 0297 00
WP 0298 00
WP 0299 00
ii
TM 5-3805-261-23-2
Table of Contents - Continued

Page
Number
Front Axle
WP 0300 00
WP 0301 00
WP 0302 00
WP 0303 00
WP 0304 00
Front Axle Assembly Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Steering Arms and Tie Rod Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Spindle, Bearings, and Seals Replacement . . . . . . . . . . . . . . . . . . . . . .
Leaning Wheel Mechanism Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leaning Wheel Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0300 00-1
0301 00-1
0302 00-1
0303 00-1
0304 00-1
Differential Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential Lock Control Valve Replacement . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Axles Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Sprockets Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Final Drive Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tandem Drive Housing Assembly Maintenance. . . . . . . . . . . . . . . . . . . . . . . .
Tandem Drive Chain Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . .
0305 00-1
0306 00-1
0307 00-1
0308 00-1
0309 00-1
0310 00-1
0311 00-1
Parking Brake Actuator and Release Valve Repair. . . . . . . . . . . . . . . . . . . . . .

Service Brakes Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Brake and Wheel Spindle Housing Assembly Replacement . . . . . . . .
Remote Steer Air Valves Replacement (Type II Machine). . . . . . . . . . . . . . . .
Air Brake Valve Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Compressor Assembly Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Compressor Lines and Fittings Replacement . . . . . . . . . . . . . . . . . . . . . . .
0312 00-1
0313 00-1
0314 00-1
0315 00-1
0316 00-1
0317 00-1
0318 00-1
Steering Control Pump Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Steering Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering Valve Maintenance (Dual Valve Design) . . . . . . . . . . . . . . . . . . . . . .
Steering Valve Maintenance (Single Valve Design). . . . . . . . . . . . . . . . . . . . .
Combination Valve Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0319 00-1
0320 00-1
0321 00-1
0322 00-1
0323 00-1
Rear Axle
WP 0305 00
WP 0306 00
WP 0307 00
WP 0308 00
WP 0309 00
WP 0310 00
WP 0311 00
Brakes
WP 0312 00
WP 0313 00
WP 0314 00
WP 0315 00
WP 0316 00
WP 0317 00
WP 0318 00
Steering
WP 0319 00
WP 0320 00
WP 0321 00
WP 0322 00
WP 0323 00
Frame and Articulation Systems

WP 0324 00 Frame Separation and Connection Replacement (CCE and Type I Machines) 0324 00-1
WP 0325 00 Articulation Hitch Bearing Replacement (CCE and Type I Machines) . . . . . . 0325 00-1
WP 0326 00 Articulation Hitch Bearing Replacement (Type II Machine) . . . . . . . . . . . . . . 0326 00-1
Body, Cab, Hood, and Hull
WP 0327 00 ROPS Replacement (CCE Machine). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0327 00-1
WP 0328 00 Operators Panel Console Base Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . 0328 00-1
Hydraulic Ssystem
WP 0329 00
WP 0330 00
WP 0331 00
WP 0332 00
WP 0333 00
WP 0334 00
WP 0335 00
WP 0336 00
Hydraulic Pump Assembly and Mounting Replacement . . . . . . . . . . . . . . . . .

Hydraulic Pump Assembly Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circle Drive Motor Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Control Valves Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Centershift Cylinder Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blade Tip Cylinder Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blade Lift Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Articulation Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iii
0329 00-1
0330 00-1
0331 00-1
0332 00-1
0333 00-1
0334 00-1
0335 00-1
0336 00-1
TM 5-3805-261-23-2
Table of Contents - Continued

Page
Number
Hydraulic Ssystem - Continued
WP 0337 00 Sideshift Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0337 00-1
WP 0338 00 Scarifier Cylinder Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0338 00-1
WP 0339 00 Hydraulic Tank and Mounting Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . 0339 00-1
Earth Moving Equipment Components
WP 0340 00
WP 0341 00
WP 0342 00
WP 0343 00
WP 0344 00
WP 0345 00
Blade Lift Bar Assembly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Blade Lift Arm Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drawbar Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blade Brackets Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circle Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circle Drive Swivel Assembly Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0340 00-1
0341 00-1
0342 00-1
0343 00-1
0344 00-1
0345 00-1
CHAPTER 5 SUPPORTING INFORMATION

WP 0346 00
WP 0347 00
WP 0348 00
WP 0349 00
WP 0350 00
WP 0351 00
WP 0352 00
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0346 00-1

Maintenance Allocation Chart (MAC) Introduction . . . . . . . . . . . . . . . . . . . . . 0347 00-1
Maintenance Allocation Chart (MAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0348 00-1
Expendable and Durable Items List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0349 00-1
Illustrated List of Manufactured Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0350 00-1
Torque Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0351 00-1
Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0352 00-1
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index-1
iv
TM 5-3805-261-23-2
HOW TO USE THIS MANUAL

NOTE
If at any time you are unsure how to use this manual or you cannot locate the information you need, notify
your supervisor.
INTRODUCTION
1.
This manual is designed to help you perform troubleshooting and maintenance on the 130G Series Grader.
2.
This manual is divided into chapters and written in work package format:
3.
4.
a.
Chapters divide the manual into major categories of information (e.g., General Information, Equipment
Description, and Theory of Operation; Troubleshooting Procedures; Unit Field Maintenance Instructions; Direct
Support Field Maintenance Instructions; and Supporting Information).
b.
Each Chapter is divided into work packages, which are identified by a 6-digit number (e.g., 0001 00, 0002 00, etc.)
located on the upper right-hand corner of each page. The work package page number (e.g., 0001 00-1, 0001 00-2,
etc.) is located centered at the bottom of each page.
c.
If a Change Package is issued to this manual, added work packages use the 5th and 6th digits of their number to
indicate new material. For instance, work packages inserted between WP 0001 00 and WP 0002 00 are numbered
WP 0001 01, WP 0001 02, etc.
Due to the size of this manual, it is separated into two volumes:

a.
The first volume (TM 5-3805-261-23-1) consists of Chapters 1 through 3 (through WP 0266 00).
b.
The second volume (TM 5-3805-261-23-2) contains Chapter 4.
c.
Both volumes have Chapter 5, Supporting Information, for reference purposes.
Scan through this manual to become familiar with its organization and contents before attempting to operate or maintain
the equipment.
CONTENTS OF THIS MANUAL

1.
A Warning Summary is located at the beginning of this manual. Become familiar with these warnings before operating or
performing troubleshooting or maintenance on the grader.
2.
A Table of Contents, located in the front of the manual, lists all chapters and work packages in the publication.
a.
The Table of Contents also provides Reporting Errors and Recommending Improvements information and DA
Form 2028 addresses, for the submittal of corrections to this manual.
b.
If you cannot find what you are looking for in the Table of Contents, refer to the alphabetical Index at the back of
the manual.
3.
Chapter 1, General Information, Equipment Description, and Theory of Information, provides general information on the
manual and the equipment.
4.
Chapter 2 covers Troubleshooting Procedures. WP 0005 00 contains a Troubleshooting Symptom Index. If the machine
malfunctions, this index should always be consulted to locate the appropriate troubleshooting procedure. Chapter 2 also
includes STE/ICE-R testing of selected machine systems.
5.
Chapter 3 covers Unit Field Maintenance Instructions. Major areas covered are Preventive Maintenance Checks and
Services (PMCS), Service Upon Receipt, as well as instruction on maintaining components at Unit Field Maintenance
level.
6.
Chapter 4 covers Direct Support Field Maintenance Instructions.
7.
Chapter 5 includes Supporting Information: References, Maintenance Allocation Chart (MAC) Introduction; MAC;
Expendable and Durable Items List; Tool Identification List; Illustrated List of Manufactured Items; Torque Limits; and
Schematic Diagrams.
v
TM 5-3805-261-23-2
FEATURES OF THIS MANUAL

1.
WARNINGs, CAUTIONs, NOTEs, subject headings, and other important information are highlighted in BOLD print as a
visual aid.
WARNING
A WARNING indicates a hazard which may result in injury or death.
CAUTION
A CAUTION is a reminder of safety practices or directs attention to usage practices that may result in
damage to equipment.
NOTE
A NOTE is a statement containing information that will make the procedures easier to perform.
2.
Statements and words of particular interest may be printed in CAPITAL LETTERS to create emphasis.
3.
Within a procedural step, reference may be made to another work package in this manual or to another manual. These
references indicate where you should look for more complete information.
If you are told: Refer to General Maintenance Instructions (WP 0020 00) go to Work Package 0020 00 in
this manual for instructions on general maintenance.
4.
Illustrations are placed after, and as close to, the procedural steps to which they apply. Callouts placed on the art may be
text or numbers, or both; whichever method is easier for the soldier.
5.
Numbers located at lower right corner of art (e.g., 397-001; 397-002, etc.) are art control numbers and are used for
tracking purposes only. Disregard these numbers.
6.
Dashed leader lines used in the Lubrication Chart (WP 0022 00) and in the PMCS illustrations (WP 0023 00) indicate that
called out lubrication points are located on both sides of the equipment.
7.
Unless otherwise indicated, technical instructions include metric units as well as standard units. For your reference, a
Metric Conversion Chart is located on the inside back cover of the manual.
vi
TM 5-3805-261-23-2
CHAPTER 4
DIRECT SUPPORT FIELD
MAINTENANCE INSTRUCTIONS
TM 5-3805-261-23-2
ENGINE REPLACEMENT
0267 00
THIS WORK PACKAGE COVERS

Removal, Cleaning and Inspection, Installation
INITIAL SETUP
Maintenance Level
Equipment Conditions - Continued
Direct Support
Engine off (TM 5-3805-261-10)
Tools and Special Tools
Battery cables disconnected (WP 0125 00)
Tool kit, general mechanics (Item 89, WP 0348 00)

Shop equipment, field maintenance (Item 74, WP
0348 00)
Articulation anti-pivot pin installed (TM 5-3805261-10)

Engine oil drained (WP 0024 00)
Leveler, load (Item 42, WP 0348 00)
Coolant drained (WP 0065 00)
Stand, engine (Item 85, WP 0348 00)
Radiator inlet and outlet tubes removed (WP 0057

00)
Wrench, torque (Item 96, WP 0348 00)

Lifting device, 2,300-lb capacity
Engine compartment dash plate removed (WP 0183

00)
Materials/Parts
Cap set, protective (Item 7, WP 0349 00)
Supplemental steering motor

removed (WP 0091 00)
Rag, wiping (Item 35, WP 0349 00)

Tag, marker (Item 44, WP 0349 00)
(with
pump)
Air pressure relieved (TM 5-3805-261-10)
Lockwasher (19)
Fuel tank removed (WP 0044 00)
Packing, preformed (2)
Air cleaner body removed (WP 0038 00)
Pin, cotter
Heater hoses disconnected from engine (WP 0211

00)
Personnel Required
Two
Air compressor line to air dryer disconnected (WP

0164 00)
References
WP 0020 00
Transmission oil cooler lines disconnected (WP

0298 00)
Equipment Conditions
Machine parked on level ground (TM 5-3805-26110)
Turbocharger lines and hoses removed (WP 0039

00)
Parking/emergency brake applied (TM 5-3805-26110)
Exhaust muffler and pipe removed (WP 0051 00)
Implements lowered to ground (TM 5-3805-26110)
0267 00-1
Fuel pressure switch removed (WP 0115 00)

Hydraulic pump drive removed (WP 0232 00)
TM 5-3805-261-23-2
ENGINE REPLACEMENT - CONTINUED
0267 00
REMOVAL
1.
Close fuel shutoff valve (2) on fuel tank (1).
2
397-1274
2.
Remove nut (5) from solenoid (3).
NOTE
Tag wire, cable, and harness assemblies
before disconnecting to aid in installation.
3.
Disconnect wire assembly (4) at terminal from solenoid (3).
4.
Remove nut (8) and lockwasher (7). Discard lockwasher.
5.
Disconnect wire assembly (6) and cable assemblies (9

and 10) from battery terminal of solenoid (3).
6.
Remove nut (11) and lockwasher (12). Discard lockwasher.
7.
8.
Disconnect cable assembly (13) from starting motor

(17) and slave receptacle. Remove and discard lockwasher (14).
Disconnect cable assemblies (15 and 16) from starting
motor (17).
0267 00-2
6 7 8
17
16 15 14
10
13 12
11
397-2304
TM 5-3805-261-23-2
0267 00
REMOVAL - CONTINUED
9.
Remove bolt (27), washer (28), and clip (29).
CAUTION
Cap hose and tube ends and plug open ports to prevent contamination.
NOTE
Tag hose and tube assemblies before disconnecting to aid in installation.
10.
Disconnect fuel supply hose assembly (30).
11.
Disconnect fuel return hose assembly (26).
12.
Remove and discard cotter pin (18) from pin (20).
13.
Remove pin (20).
14.
Separate linkage assembly (19) from lever of governor control assembly (21).
15.
Support governor control assembly (21).
16.
Remove three bolts (22), washers (23), and clips (24 and 25).
17.
Position governor control assembly (21) to side.
18
19
20
21
30
26
29
0267 00-3
28 27
22
23
24
22
23
25
397-1267
TM 5-3805-261-23-2
0267 00
REMOVAL - CONTINUED
18.
Remove nut (33), washer (32), and clip (31).
19.
Remove bolt (34) and washer (35).
20.
Disconnect wire assembly (36) at terminal.
21.
Remove fuel line bolt (37), washer (38), and clip (39).
39
31
32
38 37
36 35
34
0267 00-4
33
397-1268
TM 5-3805-261-23-2
0267 00
REMOVAL - CONTINUED
22.
Disconnect hose assemblies (43 and 45) from air compressor (44) and air compressor governor (46).
23.
Remove bolt (52), washer (40), and clip (41) from

supplemental steering motor mounting bracket (42).
24.
25.
Disconnect four wire assemblies (48) at terminals

from coolant temperature switch (49).
40
41
42
43
44
52
46
51
48 49
50
47
45
397-1269
26.
Disconnect tube assemblies (53 and 54).
27.
Disconnect hose (57) and clip from sampling valve assembly (55) from engine oil cooler (56).
28.
29.
53
54
63
61
55,56
62
60
59
58
0267 00-5
57
397-1270
TM 5-3805-261-23-2
0267 00
REMOVAL - CONTINUED
30.
Remove 4 screws (70) and washers (69) from engine oil pressure switches (68).
66
64
67
73
65
72
68
71
70
69
397-1271
WARNING
NOTE
Engine weighs 1,500 lb (680 kg).
31.
32.
33.
With assistance, attach sling to both lifting eyes mounted on each end of cylinder head and take up slack.
Remove 12 bolts (67) and lockwashers (66). Discard lockwashers.
Remove four bolts (73) and lockwashers (72) from trunnion on bottom-front left and right sides of engine and separate.
Discard lockwashers.
0267 00-6
TM 5-3805-261-23-2
0267 00
REMOVAL - CONTINUED
WARNING
Do not allow engine to swing. Failure to follow this warning may cause injury to personnel.
CAUTION
Clear all hose, cable, wires and other detached assemblies from engine area before lifting engine from
frame.
Lift engine slowly, always checking to be sure cables and hoses are not caught on anything. Watch for
any hoses, lines, and wires that may still be connected.
34.
Remove engine.
35.
Support on engine stand or blocking.
36.
Remove sling.
37.
Remove shim(s) (71) from front of frame, left and right sides. Tie shim(s) together and tag for identification.
NOTE
Record the number of threads on bolts that extend above nuts before removing.
38.
Remove two bolts (64) and nuts (65) from bottom-rear of engine, left and right sides.
CLEANING AND INSPECTION

Clean and inspect all parts in accordance with WP 0020 00.
INSTALLATION
1.
Install two nuts (65) and bolts (64) in rear engine mounts, left and right sides of engine.
2.
Position shim(s) (71) in same location as removed to front of frame, left and right sides.
3.
Attach sling.
4.
Position engine and lower slowly.
5.
Align flywheel with engine coupling gear. If flywheel and coupling to not engage, turn crankshaft hub mounting bolt at
front of engine. This will turn flywheel, allowing gear teeth to engage.
6.
Inspect shim(s) (71) for proper alignment.
7.
Remove sling.
8.
Install four new lockwashers (72) and bolts (73) loosely in trunnion and frame on left and right sides of bottom-front of
engine.
0267 00-7
TM 5-3805-261-23-2
0267 00
INSTALLATION - CONTINUED
9.
Install 2 of 12 new lockwashers (66) and bolt (67) in two top mounting holes in engine-to-transmission adapter, securing
adapter to engine.
10.
11.
12.
Align engine.
After proper alignment has been made, tighten four bolts (73) to 150 lb-ft (203 Nm).
Install four washers (69) and screws (70).
66
64
73
65
72
68
71
70
0267 00-8
69
397-1271
67
TM 5-3805-261-23-2
0267 00
NOTE
Route engine wiring harness between engine block and oil gauge tube.
13.
Install clip (63), washer (62), and bolt (61).
14.
15.
Connect oil sampling valve tube assemblies (53 and 54).
53
54
63
61
55,56
62
60
59
58
0267 00-9
57
397-1270
TM 5-3805-261-23-2
0267 00
NOTE
16.
17.
18.
19.
20.
Bring wire assemblies behind coolant tube for transmission oil cooler, located behind air compressor.
Connect three wire assemblies (48) on coolant temper40 41
ature switches (49).
42
43
44
Install clip (42), washer (40), and bolt (52) to supplemental steering motor mounting bracket (41).
52
Connect hose assembly (45) to air compressor governor (46).
Connect hose assembly (43) to air compressor (44).
51
46
48 49
50
47
45
0267 00-10
397-1269
TM 5-3805-261-23-2
0267 00
21.
22.
23.
24.
Install 10 of 12 new lockwashers (66) and bolts (67).

Position wire assembly (36).
Install washer (37) and bolt (36).
NOTE
25.
Secure cables to backside of engine front cover.

Install clip (31), washer (32), and nut (33).
67
66
39
38
37
0267 00-11
36
33
35
32
34
31
397-2504
TM 5-3805-261-23-2
0267 00
26.
Position governor control assembly (21).
27.
Position three washers (23) and bolts (22).
NOTE
Secure hose, cables, and governor control housing to engine front cover.
28.
Install clips (24 and 25), three washers (23), and bolts (22).
29.
Position linkage assembly (19) on lever of governor control assembly (21).
30.
Install pin (20) and new cotter pin (18).
31.
Connect fuel transfer pump hose assembly (30).
32.
Connect fuel injection pump hose assembly (26).
33.
Install clip (29), washer (28), and bolt (27) securing three starting motor cables.
18
19
20
21
30
26
29
0267 00-12
28 27
22
23
24
22
23
25
397-1267
TM 5-3805-261-23-2
0267 00
34.
Install cable assemblies (15 and 16), new lockwasher

(14), cable assembly (13), new lockwasher (12), and
nut (11) to starting motor (17). Tighten nut to 22 lb-ft
(30 Nm).
35.
Install cable assemblies (9 and 10), wire assembly (6),

new lockwasher (7), and nut (8) to solenoid battery
terminal. Tighten nut to 22 lb-ft (30 Nm).
36.
Install wire assembly (4) at terminal and nut (5) on

S terminal of solenoid (3).
6 7
8
9
10
17
37.
13 12
16 15 14
11
397-2304
Open fuel shutoff valve (2) on fuel tank (1) to turn fuel
on.
2
397-1274
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
Install hydraulic pump drive (WP 0232 00).

Install fuel pressure switch (WP 0115 00).
Install exhaust muffler and pipe (WP 0051 00).
Install turbocharger lines and hoses (WP 0039 00).
Connect transmission oil cooler line (WP 0298 00).
Connect compressor line to air dryer (WP 0164 00).
Connect heater hoses to engine (WP 0211 00).
Install air cleaner body (WP 0038 00).
Install fuel tank (WP 0044 00).
Install supplemental steering motor (with pump) (WP 0091 00).
Install engine compartment dash plate (WP 0183 00).
Install radiator inlet and outlet tubes (WP 0057 00).
Refill radiator to proper level (WP 0065 00).
Refill engine oil crankcase to proper level (WP 0024 00).
Install battery cables (WP 0024 00).
Remove articulation anti-pivot pin (TM 5-3805-261-10).
Turn disconnect switch to ON position and start engine (TM 5-3805-261-10).
Check for leaks.
Stop engine.
END OF WORK PACKAGE

0267 00-13/(-14 Blank)
TM 5-3805-261-23-2
ENGINE MOUNTING AND TRUNNION REPLACEMENT
0268 00

Removal, Disassembly, Cleaning and Inspection, Assembly, Installation
INITIAL SETUP
Maintenance Level
Direct Support

Materials/Parts
Detergent (Item 11, WP 0349 00)
Engine off (TM 5-3805-261-10)
Battery disconnect switch in OFF position (TM 53805-261-10)
References
WP 0020 00
Hub drive removed (WP 0271 00)
REMOVAL
1.
Remove two screws (1), washers (2), and plates (3) from top-front of engine.
2.
Remove two screws (6), washers (5), and plate (4) from top-rear of engine.
1 2
397-1275
0268 00-1
TM 5-3805-261-23-2
ENGINE MOUNTING AND TRUNNION REPLACEMENT - CONTINUED
0268 00
REMOVAL - CONTINUED
3.
Remove two bolts (8) and bracket (7) from bottomrear of engine.
4.
Remove dowel (9) from bracket (7).
5.
Remove two bolts (12) and bracket (11) from bottomrear of engine.
6.
Remove dowel (10) from bracket (11).
12
12
11 10
9
8
397-1276
7.
Remove six bolts (16), washers (17), and support (18) from bottom-front of engine.
CAUTION
Use care when removing and installing trunnion to prevent damage to crankshaft front seal.
8.
Remove three bolts (13), trunnion (15), and preformed

packing (14) as an assembly. Discard preformed packing.
13
18
14
17
15
16
0268 00-2
397-1277
TM 5-3805-261-23-2
0268 00
DISASSEMBLY
NOTE
Do not disassemble trunnion assembly unless preformed packing is worn or defective.
9.
15
Remove trunnion (15) and preformed packing (20)

from support (19). Discard preformed packing.
20
19
397-1278

ASSEMBLY
NOTE
If trunnion preformed packing was replaced, go to step 1. If preformed packing was not replaced, go to step
2.
1.
Install new preformed packing (20) in support (19). Preformed packing must be recessed 0.040 to 0.080 in. (1.02 to 2.03
mm) from back edge of support.
2.
Lubricate inner surface of preformed packing (20) with 3 percent detergent solution to facilitate trunnion (15) installation.
3.
Install trunnion (15) in support (19).
INSTALLATION
1.
Install new preformed packing (14), trunnion (15), and three bolts (13).
2.
Install support (18), six washers (17), and bolts (16).
3.
Install dowel (10) on bracket (11).
4.
Install bracket (11) and two bolts (12) on bottom-rear of engine.
5.
Install dowel (9) on bracket (7).
6.
Install bracket (7) and two bolts (8) on bottom-rear of engine.
0268 00-3
TM 5-3805-261-23-2
0268 00
7.
Install plate (4), two washers (5), and screws (6) on top-rear of engine.
8.
Install two plates (3), washers (2), and screws (1) on top-front of engine.
1 2
397-1275
9.
Install hub drive (WP 0271 00).
END OF WORK PACKAGE
0268 00-4
TM 5-3805-261-23-2
ENGINE FRONT COVERS REPLACEMENT
0269 00

INITIAL SETUP
Maintenance Level
References
WP 0020 00
Direct Support


0348 00)
Materials/Parts
Engine off (TM 5-3805-261-10)
Gasket cement (Item 16, WP 0349 00)

Engine mounting and trunnion removed (WP 0268

00)
Gasket (2)
Water pump removed (WP 0060 00)
Packing, preformed
Air compressor removed (WP 0317 00)
REMOVAL
1.
Remove two bolts (3), washers (2), and cover (1).
2.
Remove preformed packing (4) from cover (1). Discard preformed packing.
1
4
397-1280
0269 00-1
TM 5-3805-261-23-2
ENGINE FRONT COVERS REPLACEMENT - CONTINUED
0269 00
REMOVAL - CONTINUED
NOTE
Mark all bolts to ensure that they are installed in their original positions during installation.
3.
Remove six nuts (12) and washers (13).
4.
Remove cover (11) and gasket (10). Discard gasket.
5.
Remove 21 bolts (9), nuts (6), and washers (5).
6.
Remove cover (8) and gasket (7). Discard gasket.
13
12
11
10
397-1281

INSTALLATION
NOTE
1.
Position new gasket on timing gear plate and cut gasket even with bottom face of cylinder block before
installing.
Gasket cement is applied to bottom of gasket where it contacts oil pan plate gasket.
Apply gasket cement to bottom of new gasket (7) and install new gasket.
NOTE
Position timing gear cover on timing gear plate.
2.
Install timing gear cover (8).
3.
Install 21 bolts (9), washers (5), and nuts (6). Tighten nuts to 14 to 20 lb-ft (19 to 27 Nm).
0269 00-2
TM 5-3805-261-23-2
ENGINE FRONT COVERS REPLACEMENT - CONTINUED
0269 00
4.
Install new preformed packing (4), cover (1), two

washers (2), and bolts (3).
1
4
397-1280
5.
6.
7.
Install air compressor (WP 0317 00).

Install water pump (WP 0060 00).
Install engine mounting and trunnion (WP 0268 00).
END OF WORK PACKAGE
0269 00-3/(-4 Blank)
TM 5-3805-261-23-2
CYLINDER BLOCK HEAD ASSEMBLY MAINTENANCE
0270 00

INITIAL SETUP
References
Maintenance Level
WP 0020 00
Direct Support
WP 0235 00
WP 0274 00

0348 00)
Sling (Item 78, WP 0348 00)


Lifting device, 150-lb capacity
Engine off (TM 5-3805-261-10)

Materials/Parts
Detergent (Item 11, WP 0349 00)
Hood removed (WP 0181 00)

Air cleaner body removed (WP 0038 00)
Oil, lubricating (Item 27, 28, or 29, WP 0349 00)
Turbocharger air lines removed (WP 0039 00)

Temperature regulator (thermostat) removed (WP

0059 00)
Gasket (4)
Coolant switch removed (WP 0114 00)
Packing, preformed
Ether aid switch removed (WP 0114 00)
Plug (12)
Supplemental steering pump motor removed (WP

0091 00)
Seal (16)
Rocker arm assembly removed (WP 0273 00)
Personnel Required
Exhaust manifold removed (WP 0277 00)

Fuel injector nozzles removed (WP 0278 00)
Two
REMOVAL
CAUTION
Cap all hose and tube ends to prevent contamination.
NOTE
Tag all hose and tube assemblies before disconnecting to aid in installation.
0270 00-1
TM 5-3805-261-23-2
CYLINDER BLOCK HEAD ASSEMBLY MAINTENANCE - CONTINUED
0270 00
REMOVAL - CONTINUED
1.
Remove tube (1) from tube assembly (12) and atomizer (2) on top-left side of engine.
2.
Remove atomizer (2) from cylinder head (11).
3.
Disconnect tube assembly (3).
4.
Remove elbow (4).
5.
Disconnect tube assembly (8).
6.
Remove connector (9) and bushing (10).
7.
Loosen two clamps (6) on left side of engine.
8.
Remove hose (7) from pipe (5).
1
2 3 4
12
10 9
11
8
7
397-1299
9.
Remove bolts (18 and 19) and two bolts (17) from
front-left side of engine.
10.
Separate elbow (22) from cylinder block head (11) and

water pump (20).
11.
Remove and discard gaskets (16 and 21).
12.
Remove five screws (15), 14 bolts (14), and washers

(13) from top of cylinder block head (11).
14
15
13
16
17
18
11
22
21
20
WARNING
0270 00-2
19
397-1300
TM 5-3805-261-23-2
0270 00
REMOVAL - CONTINUED
NOTE
Cylinder block head assembly weighs 129 lb (59 kg).
13.
Attach sling to plates (23 and 25).
14.
Remove cylinder block head assembly (24) from block (28), using sling.
23
24
34
25
30
33
26
29
31
32
27
28
397-1301
CAUTION
Do not set machined surfaces of cylinder block head assembly on an abrasive surface. Concrete and abrasive
metal surfaces can scratch and cause damage to the cylinder block head assembly.
15.
Detach sling from plates (23 and 25). Do not remove plates.
16.
Remove gasket (26), plate (34), preformed packing (33), gasket (32), preformed packing (29), four seals (30), and 12
seals (31) from top of engine. Discard gaskets, preformed packings, and seals.
0270 00-3
TM 5-3805-261-23-2
0270 00
DISASSEMBLY
1.
Remove four bolts (35), washers (36), cover (37), and

gasket (38). Discard gasket.
32
23
33
34
35
36
NOTE
37
38
Plates can remain installed on cylinder

block head assembly to facilitate installation.
39
40
2.
Remove four screws (32), washers (40), and plates (23

and 25).
3.
Remove three plugs (39).
25
41
NOTE
To remove plugs, drill hole through plug
and pry out.
40
32
397-1302
4.
Remove and discard four plugs (33 and 34) and eight
plugs (41).
ASSEMBLY
1.
Reduce temperature of eight new plugs (41) and four new plugs (33 and 34) and install using driver and hammer.
2.
Install three plugs (39).
3.
Install plates (23 and 25), four washers (40), and screws (32).
4.
Install new gasket (38), cover (37), four washers (36), and bolts (35).
0270 00-4
TM 5-3805-261-23-2
0270 00
INSTALLATION
1.
Position 12 new seals (31), four new seals (30), and new preformed packing (29) on spacer plate (27).
2.
Install new gasket (32), new preformed packing (33), plate (34), and new gasket (26) over spacer plate (27) on dowels in
block.
3.
Attach sling.
4.
Position cylinder block head assembly (24) over engine using sling, align with dowels in block (28), and install.
23
24
34
25
30
33
26
29
31
32
27
28
397-1301
0270 00-5
TM 5-3805-261-23-2
0270 00
5.
Install 14 washers (13) and bolts (14), and five screws

(15) loosely on cylinder head (11). Lubricate threads
on five screws with oil.
6.
Install rocker arm assembly (WP 0273 00).
7.
Tighten cylinder block head (11) bolts A through R in

letter sequence to 115 lb-ft (156 Nm).
8.
Tighten bolts A through R to 185 lb-ft (291 Nm).
9.
Tighten bolts A through R again in letter sequence to

185 lb-ft (251 Nm).
10.
Tighten bolts S through W in letter sequence to 32 lb-ft (43 Nm).
11.
Adjust valves (WP 0274 00).
12.
Position new gaskets (16 and 21) and elbow (22) on

left-front of engine.
13.
Install two bolts (17) and bolts (18 and 19).
397-1303
11
14
15
13
16
17
18
11
22
21
20
0270 00-6
19
397-1300
TM 5-3805-261-23-2
0270 00
14.
Position two clamps (6) on hose (7), slide hose (7) on

pipe (5), and tighten two clamps (6).
15.
Install bushing (10), connector (9), and tube assembly

(8).
16.
Install elbow (4) and connect hose assembly (3).
17.
Install atomizer (2) to top-left of cylinder block head

(11).
18.
Install tube (1) on tube assembly (12) and atomizer

(2).
1
2 3 4
12
11
10 9
8
7
397-1299
19.
Remove sling.
20.
Install fuel injector nozzles (WP 0278 00).
21.
Install exhaust manifold (WP 0277 00).
22.
Install rocker arm assembly (WP 0273 00).
23.
Install supplemental steering pump motor (WP 0091 00).
24.
Install ether aid switch (WP 0114 00).
25.
Install coolant switch (WP 0114 00).
26.
Install temperature (thermostat) regulator (WP 0059 00).
27.
Install turbocharger air lines (WP 0039 00).
28.
Install air cleaner body (WP 0038 00).
29.
Install hood (WP 0181 00).
END OF WORK PACKAGE
0270 00-7/(-8 Blank)
TM 5-3805-261-23-2
HUB DRIVER REPLACEMENT
0271 00

INITIAL SETUP
References
WP 0020 00
Maintenance Level
Direct Support
Engine off (TM 5-3805-261-10)
Engine removed (WP 0267 00)

0348 00)
Puller (Item 54, WP 0348 00)
Materials/Parts
REMOVAL
1.
Loosen bolt (3) at front of engine. Do not remove.
2.
Use puller to loosen hub (1) from crankshaft.
3.
Remove bolt (3), washer (2), and hub (1).
397-1304

0271 00-1
TM 5-3805-261-23-2
HUB DRIVER REPLACEMENT - CONTINUED
0271 00
INSTALLATION
1.
Position hub (1) on crankshaft.
2.
Install washer (2) and bolt (3). Tighten bolt to 230 lbft (312 Nm). Tap with hammer. Retighten bolt to 230
lb-ft (312 Nm).
397-1304
3.
Install engine (WP 0267 00).
END OF WORK PACKAGE
0271 00-2
TM 5-3805-261-23-2
FLYWHEEL AND FLYWHEEL HOUSING REPLACEMENT
0272 00

INITIAL SETUP
References
Maintenance Level
Direct Support
WP 0020 00


0348 00)
Bracket, lifting (Item 10, WP 0348 00)
Bracket, link (2) (Item 18, WP 0348 00)

1/2-13NC guide bolt (2)
Engine off (TM 5-3805-261-10)
5/8-18NF guide bolt (2)


Materials/Parts
Gasket cement (Item 16, WP 0349 00)

Starting motor removed (WP 0067 00)
Gasket
Oil pan and plate removed (WP 0275 00)
0272 00-1
TM 5-3805-261-23-2
FLYWHEEL AND FLYWHEEL HOUSING REPLACEMENT - CONTINUED
0272 00
REMOVAL
1.
Remove plugs (1 and 4) from rear of engine.
2.
Using scriber, matchmark flywheel assembly (2) and crankshaft at same location.
3.
Install two link brackets and 3/8-16-2B bolt on flywheel assembly (2).
WARNING
NOTE
Flywheel assembly weighs 120 lb (54 kg).
4.
Attach sling to link brackets.
5.
Install 5/8-18NF guide bolts.
6.
Remove seven screws (3).
7.
Remove two screws (3).
8.
Use sling to remove flywheel assembly (2).
9.
Remove sling and link bracket.
3/8-16-2B BOLT
3
397-1305
0272 00-2
TM 5-3805-261-23-2
0272 00
REMOVAL - CONTINUED
10.
Install two link brackets and 3/8-16-2B bolts on flywheel housing (6).
WARNING
NOTE
Flywheel housing weighs 86 lb (40 kg).
11.
12.
Remove 13 bolts (7).
13.
Remove flywheel housing (6), using sling.
14.
Remove gasket (5) and discard.
15.
Remove sling, two 3/8-16-2B bolts, and link brackets.
5
6

0272 00-3
397-1306
3/8-16-2B BOLT
TM 5-3805-261-23-2
0272 00
INSTALLATION
1.
Apply gasket cement to gasket (5).
2.
Position new gasket (5) on rear of engine block.
3.
Install two link brackets and 3/8-16-2B bolts on flywheel housing (6).
4.
5.
Install two 1/2-13NC guide bolts.
6.
Position flywheel housing (6) on 1/2-13NC guide

bolts, using sling.
7.
Install 11 of 13 bolts (7).
8.
Remove two 1/2-13NC guide bolts.
9.
Install remaining two of 13 bolts (7).
5
6
397-1306
3/8-16-2B BOLT
6
7
397-1307
1/2-13NC GUIDE BOLTS
0272 00-4
TM 5-3805-261-23-2
0272 00
10.
Tighten 13 bolts (7), in sequence, to 75 lb-ft (102

Nm).
11.
Trim new gasket (5) even with bottom of cylinder

block and flywheel housing (6).
12.
Remove sling, two 3/8-16-2B bolts, and link brackets.
7
397-1308
13.
Install two 5/8-18NF guide bolts in end of crankshaft.
14.
Install link brackets and 3/8-16-2B bolt on flywheel

assembly (2).
15.
16.
Position flywheel assembly (2) over end of crankshaft,

using sling.
17.
Align matchmarks on flywheel assembly (2) and

crankshaft.
18.
Position flywheel assembly (2) on two 5/8-18NF

guide bolts, using sling.
3/8-15-2B BOLT
LINK
BRACKET
5/8-18NF
GUIDE BOLTS
2
397-1309
19.
Install seven of nine screws (3).
20.
Remove two 5/8-18NF guide bolts.
21.
Install remaining two screws (3).
22.
Install plugs (1 and 4).
23.
Remove sling, 3/8-16-2B bolt, and link brackets.
5
(HIDDEN) 4
24.
25.
26.
27.
Install oil pan and plate (WP 0275 00).

Apply gasket cement to bottom of gasket (5), where gasket contacts oil pan plate.
Install starting motor (WP 0067 00).
END OF WORK PACKAGE

0272 00-5/(-6 Blank)
397-1310
TM 5-3805-261-23-2
ROCKER ARM ASSEMBLY MAINTENANCE
0273 00

Removal, Cleaning and Inspection, Installation, Adjustment
INITIAL SETUP
Maintenance Level
Materials/Parts - Continued
Plug (2)
Direct Support
Ring, retaining

0348 00)
Washer, spring tension (2)

References
WP 0020 00
WP 0067 00
Gear, engine turning (Item 28, WP 0348 00)
Housing, gear shaft (Item 31, WP 0348 00)

3/8-16NC bolt
Magnet
Materials/Parts
Antiseize compound, (Item 6, WP 0349 00)
Engine off (TM 5-3805-261-10)
Oil, lubricating (Item 26, 27, or 30 WP 0349 00)

Packing, preformed
Valve cover removed (WP 0031 00)
0273 00-1
TM 5-3805-261-23-2
ROCKER ARM ASSEMBLY MAINTENANCE - CONTINUED
0273 00
REMOVAL
NOTE
Remove parts only as necessary to replace damaged parts.
1.
Remove four bolts (1) and washers (2) from top of cylinder head (4).
2.
Lift valve mechanism assembly (3) straight up to remove.
NOTE
1
2
ID each push rod and tappet during

removal, to facilitate installation.
3.
Remove eight push rods (6).
4.
Use magnet to remove eight tappets (5).
5.
Remove retaining ring (9), washer (10), spring tension

washer (11), and washer (12). Discard spring tension
washer and retaining ring.
6
5
4
397-1311A
6.
Remove rocker arm assembly (14) from shaft (7).
7.
Remove nut (8) and screw (13) from rocker arm

assembly (14).
8.
Remove bracket (16).
9.
Remove pin (15) from bracket (16).
10.
Remove rocker arm (18).
11.
Remove nut (19) and screw (17) from rocker arm

assembly (18).
7
19
18
17 16
0273 00-2
15
14
13 12
8
11
10 9
397-1312
TM 5-3805-261-23-2
0273 00
REMOVAL - CONTINUED
12.
Remove washer (21), spring (22), and washer (23).
13.
Remove rocker arm assembly (25).
14.
Remove nut (20) and screw (24) from rocker arm (25).
15.
16.
17.
18.
7
30
20
29
28
19.
20.
21.
22.
23.
24.
25.
27
26 25
24
23
22
397-1314
21
7
41
40
31
39
38
37
36
35
34
33
397-1316
32
0273 00-3
TM 5-3805-261-23-2
0273 00
REMOVAL - CONTINUED
26.
27.
28.
29.
Remove bracket assembly (48).
30.
Remove preformed packing (55) from bracket (48)

and discard.
42
43 44
45
46
47
48
31.
Remove shaft (56) from bracket (48).
32.
33.
57
56
55
54
53
34.
52
49
51
397-1317
50
Remove washer (45), spring tension washer (44), washer (43), and ring (42) from shaft (7). Discard spring tension
washer.
NOTE
To remove plugs, drill and pry out.
35.
58
Remove two plugs (58) from shaft (7) and discard.
58
397-1318

1.
2.

Inspect for damaged or bent push rods.
0273 00-4
TM 5-3805-261-23-2
0273 00
INSTALLATION
1.
Install two new plugs (58) in ends of shaft (7). Tap in with hammer until flush with ends of shaft.
2.
Install ring (42), washer (43), new spring tension washer (44), and washer (45) on shaft (7).
3.
Install screw (47) and new locknut (46) on rocker arm (57). Hand-tighten locknut.
4.
Install rocker arm assembly (57) on shaft (7).
NOTE
Align bracket with large hole on end.
5.
Position bracket (48) on shaft (7).
6.
Install shaft (56) in bracket (48). Shaft must extend 0.378 in. (9.60 mm) out of bracket.
7.
Install new preformed packing (55) in bracket (48).
8.
Install screw (52) and new locknut (54) on rocker arm (53). Hand-tighten locknut.
9.
Install rocker arm assembly (53).
10.
Install washer (51), spring (50), and washer (49) on shaft (7).
11.
Install screw (39) and new nut (41) on rocker arm

(40). Hand-tighten nut.
12.
13.
Install pin (37) in bracket (38); pin must extend 0.23

in. (5.8 mm) out of bracket.
14.
Install bracket (38).
15.
Install screw (35) and nut (31) on rocker arm (36).

Hand-tighten nut.
16.
17.
Install washer (34), spring (33), and washer (32).
7
41
40
31
39
38
37
36
35
34
33
397-1316
32
0273 00-5
TM 5-3805-261-23-2
0273 00
18.
Install screw (28) and nut (30) on rocker arm (29). Hand-tighten nut.
19.
20.
Install pin (26) in bracket (27).
NOTE
Pin must extend 0.23 in. (5.8 mm) out of
bracket.
21.
Install bracket assembly (27).
22.

Hand-tighten nut.
23.
24.
Install washer (23), spring (22), and washer (21).
25.

Hand-tighten nut.
26.
Install rocker arm assembly (18) on shaft (7).
30
20
29
28
27
26 25
24
23
22
397-1314
21
NOTE
Pin must extend 0.23 in. (5.8 mm) out of
bracket.
27.
Install pin (15) in bracket (16).
28.
29.

Hand-tighten nut.
30.
31.
Install washer (12), spring tension washer (11), washer

(10), and new retaining ring (9) on shaft (7).
0273 00-6
19
18
17 16
15
14
13 12
8
11
10 9
397-1312
TM 5-3805-261-23-2
0273 00
NOTE
Install push rods and tappets in original positions.
Install flat end of tappets first and ball end of push rods to mate with tappets.
32.
Lubricate eight tappets (5) and push rods (6) with oil and install in cylinder head (4) in original positions.
33.
Cover threads of one bolt (1) with tape to protect preformed packing (55) in bracket (48).
34.
Install washer (2) and bolt (1) with taped threads

through bolt hole in bracket (48). Remove tape.
35.
Install three washers (2) and bolts (1) through brackets

(16, 27, and 38).
36.
Apply antiseize compound to threads of four bolts (1).
37.
Install valve mechanism assembly (3), bolts (1), and

washers (2) on cylinder head (4) as an assembly.
48
38
27
55
(HIDDEN)
1
2
16
3
6
5
4
397-1311A
CAUTION
Adjusting screws must be loose and seated on push rods before installing bolts.
38.
Tighten four bolts (1) in sequence to 115 lb-ft (156

Nm).
39.
Tighten four bolts (1) in sequence to 185 lb-ft (251

Nm).
40.
Repeat tightening four bolts (1) in sequence to 185 lbft (251 Nm).
397-1320
0273 00-7
TM 5-3805-261-23-2
0273 00
ADJUSTMENT
NOTE
The following step is for locating number one cylinder Top Center (TC).
1.
Remove starting motor (59) on right side of engine (WP 0067 00).
2.
Install engine turning gear on starting motor mounting flange.
NOTE
In the following steps, the engine is viewed from the flywheel end.
3.
Turn engine clockwise 30 degrees, using engine turning gear to remove timing gear play.
4.
Remove plug (60).
5.
Turn engine counterclockwise, using engine turning

gear and ratchet. Look through hole where plug (60)
was removed for threaded hole in flywheel where 3/816NC bolt can be installed. If hole is passed, repeat
step 3.
59
60
0273 00-8
397-1321
TM 5-3805-261-23-2
0273 00
ADJUSTMENT - CONTINUED
NOTE
Number one cylinder must be at compression stroke for proper valve adjustment.
6.
Check number one cylinder for compression stroke. Intake and exhaust valves must be closed. This can be checked by
visually inspecting the valves and by movement in both rocker arms. If exhaust valve is open, remove 3/8-16NC bolt
and turn engine 360 degrees.
7.
Adjust intake valves for cylinders 1 and 2. Turn adjusting screws (13) in arms (18 and 29) until a clearance of 0.012 to
0.018 in. (0.30 to 0.46 mm) is obtained. Secure screws (13) with nuts (8).
8.
Adjust exhaust valves for cylinders 1 and 3. Turn adjusting screws (13) in arms (14 and 34) until a clearance of 0.022 to
0.028 in. (0.56 to 0.71 mm) is obtained between arms (14 and 34) and push rods (6). Secure screws (13) with nuts (8).
NOTE
Remove 3/8-16NC bolt from flywheel before turning engine.
9.
Turn engine counterclockwise 360 degrees. Verify

that number 4 cylinder is at TC position.
10.
Install 3/8-16NC bolt in flywheel.
11.
Adjust intake valves for cylinders 3 and 4 by turning

screws in arms (37 and 56). Repeat adjustment procedures in step 7.
12.
Adjust exhaust valves for cylinders 2 and 4 by turning

screws in arms (25 and 51). Repeat adjustment procedures in step 8.
13.
Tighten eight nuts (8). Hold adjusting screws and

tighten eight nuts to 22 lb-ft (30 Nm).
56
51
37
34
29
25
8
13
18
14
6
5
397-1322
14.
Remove engine turning gear.
15.
Remove 3/8-16NC bolt from flywheel housing.
16.
Install valve cover (WP 0031 00).
END OF WORK PACKAGE

0273 00-9/(-10 Blank)
TM 5-3805-261-23-2
VALVES MAINTENANCE
0274 00

Removal, Disassembly, Cleaning and Inspection, Testing, Repair, Assembly, Installation, Testing
INITIAL SETUP
Maintenance Level
Direct Support
References

0348 00)
Bushing driver, valve (Item 19, WP 0348 00)
WP 0020 00
Compressor, valve spring (Item 20, WP 0348 00)

Extractor, valve group (Item 25, WP 0348 00)
Gage, profile (Item 26, WP 0348 00)

Gage, profile (Item 27, WP 0348 00)
Tester, spring resiliency (Item 88, WP 0348 00)
Engine off (TM 5-3805-261-10)
Materials/Parts
Oil, lubricating (Item 27, 28, or 29 WP 0349 00)
Prussian blue (Item 34, WP 0349 00)
Cylinder block head removed (WP 0270 00)
REMOVAL
NOTE
The following maintenance procedure is for one valve. Follow these instructions for the remaining seven
valves.
1.
Position valve spring compressor on valve spring (1)

and bottom of valve on cylinder block head (2).
2.
Compress valve spring (1).
VALVE SPRING
COMPRESSOR
0274 00-1
397-1323
TM 5-3805-261-23-2
VALVES MAINTENANCE - CONTINUED
0274 00
REMOVAL - CONTINUED
WARNING
Use extreme caution when removing locks and rotocoil assembly. Wear safety glasses. Uncontrolled release
of the valve spring may cause injury to personnel.
NOTE
Tag all parts before removal to aid in installation.
3.
Carefully remove two locks (4) and rotocoil assembly

(3) from valve stem (5). Do not release valve spring
(1).
4.
Slowly release valve spring compressor.
5.
Remove valve spring (1) and valve stem (5) from cylinder block head (2).
3
1
5
397-1324
DISASSEMBLY
NOTE
Remove guides and washers only if inspection indicates replacement is necessary.
1.
Inspect eight valve stem guides (6). Replace if

cracked, broken, grooved, scored, or bore diameter
exceeds 0.3772 in. (9.581 mm).
2.
Use driver and hammer to remove damaged or worn

guide (6) from bottom of cylinder block head (2).
3.
Inspect four exhaust valve seats (7) and intake washers (8). Replace if cracked, broken, burned, or pitted.
4.
Use valve seat extractor to remove intake washers (8).
VALVE SEAT
EXTRACTOR
8
6
7
0274 00-2
397-2221
TM 5-3805-261-23-2
0274 00

TESTING
Test valve springs (1), using spring resiliency tester. Length of spring under test
force of 53 to 62 lbf (236 to 276 N) must
be 1.766 in. (44.86 mm). Free length after
test must be 2.05 in. (5.2 cm).
397-1326
0274 00-3
TM 5-3805-261-23-2
0274 00
REPAIR
1.
Grind four exhaust valve seats (7) and intake washers (8) to an angle of 30 degrees.
NOTE
To reduce maximum seat angle, grind seat face to 15 degrees.
2.
Grind seat face to 15 degrees, if necessary.
NOTE
Valves must be matched with the exhaust valve seat or intake washer with which they are measured. Mark
valve and matching valve seat or washer to identify matching sets.
3.
4.
5.
Measure valve recess for four exhaust valve seats (7). Minimum dimension between combustion surface and exhaust
valve (9) face is 0.026 in. (0.66 mm).
Measure valve recess for four intake washers (8). Minimum dimension between combustion surface and intake valve (5)
face is 0.006 in. (0.15 mm).
Match and mark four exhaust valves (9) and intake valves (5) with their respective exhaust valve seats or intake washers.
NOTE
Angle of exhaust and intake valves must be 29-1/4 degrees.
6.
7.
Grind four exhaust valves (9) and four intake valves (5).
Apply prussian blue to face of four exhaust valves (9) and intake valves (5) and install into matchmarked valve seat (7)
or intake washer (8) respectively.
NOTE
In the following step, if blue is transferred to center of valve face, contact is correct. If blue is transferred to
top of valve face, lower valve seat or washer by grinding. If blue is transferred to bottom edge of valve face,
raise valve seat or washer by grinding.
8.
Turn valve stem allowing valve face to lightly contact face of valve seat or washer. Remove valve. Observe blue transfer, grind as necessary.
VALVE SEAT EXTRACTOR

2
0.26 IN.
(0.66 MM)
EXHAUST
15o
8
5
0.006 IN.
(0.15 MM)
INTAKE
15
7
9
o
397-2506
0274 00-4
397-1325A
TM 5-3805-261-23-2
0274 00
ASSEMBLY
CAUTION
When installing new valve seat or washer, do not expand extractor tooling diameter.
1.
Chill four exhaust valve seats (7) and intake washers (8).
2.
Use extractor to install exhaust valve seats (7) and intake washers (8) in cylinder block head (2). Press until seated on
counterbore.
3.
Measure valve recess. Valve must be below combustion surface with no protrusion.
NOTE
Eight guides must contact enough to allow easy fit into cylinder.
Minimum diameter of bore of new guides after installation is 0.3723 in. (9.456 mm).
4.
Lower temperature of eight guides (6).
5.
If removed, use driver and press to install eight new

guides (6). Ensure that guides extend above top of cylinder blockhead (2) by 0.875 in. (22.23 mm).
6.
Remove all burrs and clean eight new guides (6) after
installation.
COUNTERBORE
OF HEAD
0274 00-5
397-1327
TM 5-3805-261-23-2
0274 00
INSTALLATION
1.
Use clean engine oil to lubricate each valve stem.
2.
Install intake valve (5), or exhaust valve (9), and valve spring (1) in correct location in cylinder block head (2).
WARNING
Use caution when valve spring is compressed. Wear safety glasses when installing valve spring assembly.
Accidental release of valve spring may cause injury to personnel.
3.
Position valve spring compressor on top of valve

spring (1).
4.
Tighten compression spring.
5.
Install rotocoil assembly (3) to valve stem.
6.
Position two locks (4) into grooves on valve stem.
7.
Install two locks (4).
VALVE SPRING
COMPRESSOR
397-1323
NOTE
Be sure locks are in correct position in grooves on valve stems before removing valve spring compressor.
8.
Remove valve spring compressor carefully from cylinder block head (2).
TESTING
1.
Mark rotocoil assembly (3) with chalk. Tap lightly with soft-tip plastic hammer six to eight times.
NOTE
4
3
1
Rotocoil assembly must turn when tapped

with hammer several times. Replace rotocoil assembly if it does not turn.
5
9
2.
Install cylinder block head (WP 0270 00).
END OF WORK PACKAGE

0274 00-6
397-2219
TM 5-3805-261-23-2
OIL PAN AND OIL PAN PLATES REPLACEMENT
0275 00

INITIAL SETUP
Maintenance Level
Direct Support

3/8-16NC guide bolt (2)

Materials/Parts
Engine off (TM 5-3805-261-10)
Gasket (2)
WP 0020 00
Engine oil level gauge and tube removed (WP 0027

00)
WP 0276 00
References
0275 00-1
TM 5-3805-261-23-2
OIL PAN AND OIL PAN PLATES REPLACEMENT - CONTINUED
0275 00
REMOVAL
CAUTION
NOTE
1.
Remove hose assembly (10) from bottom of engine.
2.
Remove two bolts (12), elbow (9), and gasket (8). Discard gasket.
3.
Support oil pan (4).
4.
Remove bolt (6), cap screws (7), 17 screws (13), and 24 of 39 washers (5).
5.
Remove oil pan (4) and gasket (3). Discard gasket.
6.
Loosen plug (14).
7.
Remove 15 bolts (15), 15 of 39 washers (5), plate assembly (2), and gasket (1). Discard gasket.
8.
Remove oil pump scavenger tube (WP 0276 00).
9.
Remove plug (11) from elbow (9).
5
15
14
5
13
11
12
9
10
7
397-1329

Clean and inspect all parts in accordance with WP 0020 00. Remove all gasket material from mounting surfaces.
0275 00-2
TM 5-3805-261-23-2
OIL PAN AND OIL PAN PLATES REPLACEMENT - CONTINUED
0275 00
INSTALLATION
1.
Install plug (11) in elbow (9).
2.
Attach oil pump scavenger tube to plate assembly (2).
3.
Install new gasket (1), plate assembly (2), 15 of 39 washers (5), and 15 bolts (15). Install two 3/8-16NC guide bolts in
cylinder block to aid in installation.
4.
Install oil pump scavenger tube to oil pump (WP 0276 00).
5.
Tighten plug (14).
6.
Install new gasket (3), oil pan (4), 24 of 39 washers (5), 17 screws (13), six cap screws (7), and bolt (6). Remove two
3/8-16NC guide bolts.
7.
Install new gasket (8), elbow (9), and two bolts (12).
8.
Install hose assembly (10).
9.
Install engine oil level gauge and tube (WP 0027 00).
10.
END OF WORK PACKAGE
0275 00-3/(-4 Blank)
TM 5-3805-261-23-2
OIL PUMP AND LINES REPLACEMENT
0276 00

INITIAL SETUP
Maintenance Level
Direct Support
Ring seal

0348 00)
3/8-16NC 1-1/2 in. bolt (2)
References
WP 0020 00
WP 0234 00
Engine off (TM 5-3805-261-10)
Oil pan removed (WP 0275 00)
Materials/Parts
Lubricating oil (Item 26, 27, or 30, WP 0349 00)
Bearing
Gasket (2)
REMOVAL
1.
Remove bolts (4 and 5) from oil pump assembly (1).
2.
Support oil pump assembly (1).
3.
Remove two bolts (8), locks (9), bolts (3), and washers (2).
4.
Remove oil pump assembly (1) and gasket (7) from elbow (6).
5.
Remove gasket (7) from oil pump assembly (1). Discard gasket.
2
3
7
4
6
5
0276 00-1
397-1331
TM 5-3805-261-23-2
OIL PUMP AND LINES REPLACEMENT - CONTINUED
0276 00
REMOVAL - CONTINUED
6.
Remove two bolts (15), lock (14), bell (16), and gasket (13) from oil pump (12). Discard gasket.
NOTE
Matchmark each gear to the other gear to aid in installation.
7.
Use puller to remove gear (10).
CAUTION
Removal of bearing from gear will cause destruction of bearing. Remove bearing only if inspection indicates
replacement is necessary.
8.
Inspect bearing (11). Replace if cracked, broken, distorted, grooved, or scored.
9.
Use driver and press to remove bearing (11) if necessary.
10.
11.
Use puller to remove gear (21).
12.
Remove key (24) from oil pump shaft (20).
13.
Remove oil pan plate from bottom of engine (WP 0275 00).
14.
Remove bolt (17), lock (18), and scavenger elbow with scavenger tube (19) from oil pan plate.
CAUTION
Cap tube ends to prevent contamination.
15.
Remove elbow with tube (19) as an assembly, from oil pan plate.
10
11
12
24
23
13
14
15
22
21
16
20
17
18
19
397-2222
0276 00-2
TM 5-3805-261-23-2

REMOVAL - CONTINUED
0276 00
25
16.
Remove elbow (25) from tube (27).
17.
Remove ring seal (26) from tube (27). Discard ring

seal.
26
27
397-2223

INSTALLATION
1.
Position tube (27) to oil pan plate.
2.
Install lock (18) and bolt (17). Bend lock tab up against bolt head.
3.
Use clean oil to lubricate outer diameter of new ring seal (26) and install ring seal on tube (27).
4.
Install elbow (25) on tube (27).
5.
Install elbow with scavenger tube (19) as an assembly, on oil pan plate.
6.
Install oil pan plate (WP 0275 00).
7.
Install key (24) on oil pump shaft (20).
8.
Install gear (21) on shaft (20).
9.
Install washer (22) and bolt (23). Tighten bolt to 32 lb-ft (43 Nm).
10.
Use driver and press to install new bearing (11), if removed. Install flush with outer face of gear (10).
11.
Install gear (10). Align mark on gear (10) with mark on gear (21).
CAUTION
Pump must be filled with clean oil to prevent initial startup damage.
12.
Use clean oil to lubricate oil pump (12).
13.
Position new gasket (13) and bell (16) on oil pump (12).
14.
Install lock (14) and two bolts (15). Bend lock tabs up against bolt heads.
NOTE
Proper timing of balancer shafts and oil pump gears is obtained when 3/8-16NC holes in balancer shafts are
in alignment with holes in oil pan plate and number one cylinder is at top center compression stroke.
15.
Locate top center of compression stroke of number one cylinder on engine (WP 0234 00).
0276 00-3
TM 5-3805-261-23-2
0276 00
16.
Turn balancer shafts (29) so that the flat sides of shaft

face the opposite direction of oil pan plate (28).
17.
Install two 3/8-16NC 1-1/2 in. long bolts (30) through

oil pan plate (28) and into each balancer shaft (29).
Tighten bolts until they touch bottom of holes of balancer shafts, then loosen 1/2 turn.
28
29
30
397-1334
CAUTION
Mark on gear must be in alignment with mark on other gear.
18.
Position elbow with scavenger tube (19) as an assembly.
19.
Loosely install two washers (2), bolts (3), locks (9), and bolts (8).
20.
Position new gasket (7) between elbow with tube (19) and oil pump (12).
21.
Loosely install bolts (4 and 5).
22.
Tighten two bolts (3) and bolts (8) evenly. Bend lock (9) tabs up, toward front of engine, against bolt heads.
23.
Tighten bolts (4 and 5) evenly.
12
2
3
7
4
6
5
24.
Remove two 3/8-16NC 1-1/2 in. long bolts (30) from oil pan plate (28) and balancer shafts (29).
25.
Install oil pan (WP 0275 00).
END OF WORK PACKAGE

0276 00-4
19
397-1331
TM 5-3805-261-23-2
EXHAUST MANIFOLD REPLACEMENT
0277 00

INITIAL SETUP
Maintenance Level
Direct Support


0348 00)

Materials/Parts
Engine off (TM 5-3805-261-10)
Antiseize compound (Item 6, WP 0349 00)


Gasket (4)
Muffler and exhaust pipe removed (WP 0051 00)

References
Turbocharger removed (WP 0283 00)
WP 0020 00
Fuel injection lines removed (WP 0035 00)
WP 0046 00
REMOVAL
NOTE
1.
2.
3.
For models 130GS and 130GNS, disconnect primary fuel/priming pump as necessary (WP 0046 00) and lay aside.
Remove two bolts (7), washers (6), and shield (5)
from top-right of engine.
12
Remove four nuts (8), washers (9), two brackets (4)
11
and four washers (12).
10
Remove four nuts (10), washer (2), nut (3), and three
9
washers (11).
4
5
7
0277 00-1
397-1339
TM 5-3805-261-23-2
EXHAUST MANIFOLD REPLACEMENT - CONTINUED
0277 00
REMOVAL - CONTINUED
CAUTION
4.
5.
Remove studs only if inspection proves replacement is necessary.

Remove manifold (1) and four gaskets (16). Discard
gaskets.
1
16
Remove stud (13), four studs (14), and three studs (15)
from right side of cylinder head, if necessary. Replace
if cracked, broken, heat damaged, or if threads are
damaged.
15
14
397-1340
13

INSTALLATION
1.
2.
Install four new gaskets (16) on studs (13, 14, and 15)
on top-right of engine.
3.
Install manifold (1).
4.
Install three washers (11), washer (2), nut (3), and four
nuts (10). Tighten nuts to 32 lb-ft (43 Nm).
5.
Install four washers (12), two brackets (4), four washers (9), and nuts (8). Tighten nuts to 32 lb-ft (43 Nm).
6.
Install three studs (15), four studs (14), and stud (13)
on right side of cylinder head, if removed. Apply antiseize compound to half of studs (13, 14, and 15) being
installed in cylinder head. Tighten studs to 20 lb-ft (27
Nm).
10
11
12
9
8
Install shield (5), two washers (6), and bolts (7).
4
7
6
5
397-1339
NOTE
If disconnected, connect primary fuel filter/priming pump (WP 0046 00).
7.
8.
9.
Install fuel injection lines (WP 0035 00).

Install turbocharger (WP 0283 00).
Install muffler and exhaust pipe (WP 0051 00).
END OF WORK PACKAGE

0277 00-2
TM 5-3805-261-23-2
FUEL INJECTION NOZZLES MAINTENANCE
0278 00

Removal, Cleaning and Inspection, Testing, Installation
INITIAL SETUP
References
Maintenance Level
Direct Support
WP 0020 00

0348 00)
Adapter, nozzle (Item 8, WP 0348 00)
Puller group, nozzle (Item 58, WP 0348 00)

Tester group, nozzle (Item 87, WP 0348 00)
Engine off (TM 5-3805-261-10)
Materials/Parts
Fuel, diesel (Item 13, WP 0349 00)
Rags, wiping (Item 35, WP 0349 00)
REMOVAL
NOTE
This procedure covers replacement of one fuel injection nozzle. Follow these instructions for the remaining
three fuel injection nozzles.
0278 00-1
TM 5-3805-261-23-2
FUEL INJECTION NOZZLES MAINTENANCE - CONTINUED
0278 00
REMOVAL - CONTINUED
1.
Remove bolt (1) and clamp (4) from top of cylinder head (3).
CAUTION
2.
Do not apply more than 150 lb-in. (17 Nm) pressure to remove fuel injection nozzle.
Cap nozzle to prevent contamination if it is to be stored.
Use nozzle puller and, if necessary, nozzle puller adapter to remove fuel injection nozzle (2).
2
1
4
397-1343

0278 00-2
TM 5-3805-261-23-2
FUEL INJECTION NOZZLES MAINTENANCE - CONTINUED
0278 00
TESTING
NOTE
All carbon must be removed from injection nozzle tip before proceeding with testing.
Use nozzle tester and diesel fuel at 65 to 75F (18 to 24C) to test fuel injection nozzle for valve opening pressure. Valve
opening pressure must be 2,050 to 2,350 psi (14,134 to 16,203 kPa).
NOTE
It is possible for the pressure reading of the gauge to go down fast if the valve makes a noise (chatters) when
it opens. It is also possible for the pressure reading of the gauge to be almost constant when the valve in the
fuel injection nozzle opens.
INSTALLATION
1.
Position fuel injection nozzle (2) on top of cylinder head (3).
2.
Install clamp (4) and bolt (1).
3.
END OF WORK PACKAGE
0278 00-3/(-4 Blank)
TM 5-3805-261-23-2
FUEL INJECTION PUMP REPLACEMENT
0279 00

INITIAL SETUP
References
Maintenance Level
WP 0020 00
Direct Support
WP 0277 00
WP 0279 00

0348 00)
WP 0282 00
Wood block
Materials/Parts
Engine off (TM 5-3805-261-10)


Oil, lubricating (Item 26, 27, and 30, WP 0349 00)
Engine hood removed (WP 0181 00)
Turbocharger oil lines removed (WP 0033 00)
Gasket (2)
Secondary fuel filter and mounting removed (WP

0047 00 or WP 0048 00)
Tachometer drive removed (Models 130G,

130GSCE, and 130GNSCE ) (WP 0034 00)
Pin, cotter
Fuel transfer pump removed (Models 130G,

130GSCE, and 130GNSCE ) (WP 0281 00)
Washer, felt (4)
0279 00-1
TM 5-3805-261-23-2
FUEL INJECTION PUMP REPLACEMENT - CONTINUED
0279 00
REMOVAL
CAUTION
Plug open fuel ports and individual injection pumps to prevent contamination.
1.
Remove cotter pin (8) and pin (7) from right side of engine. Discard cotter pin.
2.
Disconnect linkage assembly (6) from fuel injection pump and governor control lever (9). Move linkage assembly out of
the way.
3.
Remove governor control lever (9) (WP 0282 00).
CAUTION
Cap hose ends to prevent contamination.
NOTE
Tag hose assemblies before disconnecting to aid in installation.
4.
Disconnect hose assembly (5) from fuel injection

pump.
5.
Remove elbow (4) and preformed packing (3). Discard preformed packing.
6.
Remove hose assembly (2).
7.
Remove manifold shield (WP 0277 00).
8.
Remove three nuts (1).
5
7
397-1344
0279 00-2
TM 5-3805-261-23-2
0279 00
REMOVAL - CONTINUED
WARNING
NOTE
Fuel injection pump and governor weighs 58 lb (26 kg).
9.
Attach sling to fuel injection pump and governor (10).
10.
Remove bolts (14 and 15) from under support (13).
11.
Remove fuel injection pump and governor (10). Pull

back to separate from front cover plate and lift up
from support (13).
12.
Remove and discard preformed packings (11, 12, 16,

and 17).
SLING
10
11
17
16
12
13
15
14
13.
Remove sling.
0279 00-3
397-1345
TM 5-3805-261-23-2
0279 00
INSTALLATION
1.
Install governor assembly on fuel injection pump (10)

(WP 0279 00).
2.
Lubricate and install new preformed packings (11, 12,

16, and 17) under fuel injection pump and governor
(10).
3.
Use sling to position fuel injection pump and governor

(10) on support (13) and timing gear plate.
4.
Install bolts (14 and 15).
10
11
17
16
12
13
15
14
0279 00-4
397-1345
TM 5-3805-261-23-2
0279 00
5.
Remove hoist.
6.
Install three nuts (1).
7.
Install manifold shield (WP 0277 00).
8.
Install governor control lever (9) (WP 0282 00).
CAUTION
After the fuel injection pump and governor are installed, move governor control lever back and forth. Preformed packing can hold rack and prevent free movement. If rack does not move freely, remove fuel injection pump and governor and reset preformed packing.
9.
Connect hose assembly (5).
10.
Install hose assembly (2), new preformed packing (3),

and elbow (4).
11.
Position linkage assembly (6) on governor control

lever (9).
12.
2
1
7
6
CAUTION
Do not attempt to start engine until fuel injection pump and governor have been adjusted.
13.
Install fuel transfer pump (Models 130G, 130GSCE, 130GNSCE) (WP 0281 00).
14.
Install tachometer drive (Models 130G, 130GSCE, 130GNSCE) (WP 0034 00).
15.
Install secondary fuel filter and mounting (WP 0047 00 or WP 0048 00).
16.
17.
Install turbocharger oil lines (WP 0033 00).
18.
Install engine hood (WP 0181 00).

0279 00-5
397-1344
TM 5-3805-261-23-2
0279 00
GOVERNOR ADJUSTMENT
CAUTION
If fuel injection pump and governor are assembled wrong, it is possible for the engine to run out of control.
Follow the next step to take the necessary precaution to stop the engine if it overspeeds.
1.
Remove turbocharger air pipe from top of engine (WP 0039 00). If engine runs out of control, a steel plate can be put
over the turbocharger air inlet to starve engine of air.
2.
Start engine (TM 5-3805-261-10). Run until normal operating temperature is reached.
LOW IDLE ADJUSTMENT
CAUTION
If engine runs out of control and governor

control lever wont shut engine off, place a
steel plate over air inlet of turbocharger.
1.
HIGH IDLE
POSITION
Position governor control lever (9) in low idle.
1
SHUT-OFF
POSITION
2.
Loosen locknut (18).
3.
Using accurate tachometer, adjust low idle screw (19).

Attach to tachometer drive at rear of governor, adjust
low idle to 800 RPM.
4.
Increase engine speed and return to low idle. Check

low idle speed again with tachometer.
5.
Tighten locknut (18).
397-1371
18
19
397-1372
6.
Stop engine.
END OF WORK PACKAGE

0279 00-6
LOW IDLE
POSITION
TM 5-3805-261-23-2
FUEL INJECTION PUMP MOUNTING REPLACEMENT
0280 00

INITIAL SETUP
Maintenance Level
Direct Support

0348 00)
Materials/Parts

Engine off (TM 5-3805-261-10)

References
Governor and fuel injection pump removed (WP

0279 00)
WP 0020 00
0280 00-1
TM 5-3805-261-23-2
FUEL INJECTION PUMP MOUNTING REPLACEMENT - CONTINUED
0280 00
REMOVAL
1.
Remove bolt (9) and washer (8) from support (6).
2.
Disconnect wire assembly (7).
3.
Remove bolts (15, 14, 11, and 10), support (6), and
preformed packings (5, 4, 3, and 2). Discard preformed packings.
4.
3
4
15
Remove plugs (1, 13, and 12) from support (6).
14
13
12
11
10
7
9

INSTALLATION
1.
Install plugs (1, 13, and 12) on support (6).
2.
Install new preformed packings (5, 4, 3, and 2), support (6) and bolts (15, 14, 11, and 10) on engine.
3.
Connect wire assembly (7).
4.
5.
Install governor and fuel injection pump (WP 0279 00).
END OF WORK PACKAGE
0280 00-2
397-1363
TM 5-3805-261-23-2
FUEL TRANSFER PUMP MAINTENANCE (MODELS 130G, 130GSCE, AND 130GNSCE)
0281 00

INITIAL SETUP
Maintenance Level
References
WP 0020 00
Direct Support

0348 00)

Materials/Parts
Engine off (TM 5-3805-261-10)
Fuel, diesel (Item 13 or 14, WP 0349 00)

Right side engine panel removed (WP 0182 00)
Air bled from fuel lines (WP 0035 00)
0281 00-1
TM 5-3805-261-23-2
FUEL TRANSFER PUMP MAINTENANCE

(MODELS 130G, 130GSCE, AND 130GNSCE) - CONTINUED
0281 00
REMOVAL
NOTE
On models 130GS and 130GNS, the fuel transfer pump is serviced elsewhere.
1.
Close fuel valve (1) on front-lower-right of fuel tank.
1
397-1406
2.
3.
Open bleed valve (19) on fuel injection pump (2) to relieve fuel pressure and close.
Loosen bolt (11).
CAUTION
NOTE
4.
5.
6.
7.
Disconnect tube assembly (10) from elbows (9 and 6) and fuel filter (7).
Disconnect hose assembly (12).
0281 00-2
TM 5-3805-261-23-2

0281 00
REMOVAL - CONTINUED
8.
9.
10.
11.
12.
Remove one of two bolts (15) and clip (16).

Install one of two bolts (15).
Remove fuel transfer pump assembly (3) from fuel injection pump (2).
19
18
17
16
11
14
13
12
3
15
5
10
9
7
397-1407
0281 00-3
TM 5-3805-261-23-2

0281 00
DISASSEMBLY
NOTE
If preformed packing is not found in housing, check injection pump for it.
1.
Remove and discard preformed packing (21) from housing (20).
WARNING
Cover is under tension from spring. Wear face shield and remove bolts carefully. Failure to follow this warning may cause injury to personnel.
21
2.
Remove two bolts (15) from housing (20).
3.
Remove cover (26), preformed packings (24 and 25),

valve (23), and spring (22). Discard preformed packings.
4.
Remove washer (27).
5.
Remove piston assembly (28).
20
28
27
22
23
24
15
26
6.
Remove valve (31) from inside piston (29).
7.
Remove preformed packing (30) from valve (31). Discard preformed packing.
25
397-1408
29
31
30
397-1409
0281 00-4
TM 5-3805-261-23-2

0281 00
DISASSEMBLY - CONTINUED
8.
Remove sleeve (33).
9.
Remove preformed packing (34) from sleeve (33).

Discard preformed packing.
10.
Remove guide and tappet assembly (32) from housing

(20).
20
32
33
34
11.
Remove and discard preformed packing (35).
12.
Remove ring (38).
13.
Separate tappet (36) and guide (37).
397-1410
35
36
38
14.
Remove two screws (42).
15.
Remove cover (41) and preformed packing (40). Discard preformed packing.
16.
Remove valve (39) from housing (20).
37
397-1411
20
39
40
41
42
397-1412

0281 00-5
TM 5-3805-261-23-2

0281 00
ASSEMBLY
1.
Install valve (39) in housing (20) with pyramid side of

valve facing out.
2.
Install new preformed packing (40) and cover (41).

Lubricate outer diameter of new preformed packing
with clean diesel fuel.
3.
20
39
40
Install two screws (42).
41
42
397-1412
4.
Position tappet (36) in guide (37).
5.
Install ring (38).
6.
Install new preformed packing (35) on groove of

guide (37). Lubricate outer diameter of new preformed
packing with clean diesel fuel.
36
37
38
7.
Install guide and tappet assembly (32) in housing (20).
8.

sleeve (33). Lubricate outer diameter of new preformed packing with clean diesel fuel.
9.
Install new preformed packing (34) and sleeve (33) as

an assembly in housing (20).
35
397-1411
20
32
33
34
0281 00-6
397-1410
TM 5-3805-261-23-2

0281 00
ASSEMBLY - CONTINUED
10.
11.
Install new preformed packing (30) on pyramid side of

valve (31). Lubricate outer diameter of valve with
clean diesel fuel.
Install new preformed packing (30) and valve (31) as
an assembly and washer (27) in piston (29).
20
29
30,31
27
397-1414
12.
Install piston assembly (28).
13.
Install spring (22).
14.
Install new preformed packings (24 and 25) in cover

(26).
15.
Position valve (23) in cover (26).
16.
Position cover (26) on housing (20). Valve (23) must

seat in spring (22).
17.
Install two bolts (15).
20
28
23
22
24
15
26
25
397-1415
INSTALLATION
1.
Install new preformed packing (21). Lubricate outer

diameter of new preformed packing with clean diesel
fuel.
21
397-1416
0281 00-7
TM 5-3805-261-23-2

0281 00
2.
Install fuel transfer pump assembly (3) on fuel injection pump (2).
NOTE
Insert tappet and seat in plunger inside fuel injection pump.
3.
Install washer (18), bolt (17), and two bolts (15).

Tighten evenly.
4.
Install washer (4) and bolt (5). Tighten evenly.
5.
Install one of two bolts (15).
6.
Install clip (16) and one of two bolts (15) securing air
bleed tube in fuel injection pump (2).
7.
Install new preformed packing (14) and elbow (13).
8.
9.
10.
Connect tube assembly (10) to elbows (6 and 9) and

fuel filter (7).
11.
19
18
17
15
16
14
13
11
Tighten bolt (11).
12
10
9
7
397-1417
0281 00-8
TM 5-3805-261-23-2

0281 00
12.
Open fuel valve (1) on front-lower-right of fuel tank.
1
397-1406
13.
Bleed air from fuel lines (WP 0035 00).
14.
Install right side engine panel (WP 0182 00).
END OF WORK PACKAGE
0281 00-9/(-10 Blank)
TM 5-3805-261-23-2
GOVERNOR CONTROLS MAINTENANCE
0282 00

INITIAL SETUP
Maintenance Level
References
WP 0020 00
Direct Support


0348 00)

Materials/Parts
Engine off (TM 5-3805-261-10)
Strap, tie (2) (Item 43, WP 0349 00)

Gasket (3)
Pin, cotter (3)
Governor switch removed (WP 0088 00)
0282 00-1
TM 5-3805-261-23-2
GOVERNOR CONTROLS MAINTENANCE - CONTINUED
0282 00
REMOVAL
1.
Remove and discard cotter pin (7) from lever (8) on fuel injection pump governor on right side of engine.
2.
Remove pin (5) from rod assembly (4).
3.
Separate rod end (6) from lever (8).
4.
Remove and discard cotter pin (2) from inner-right side of dash panel in engine compartment.
5.
Remove pin (3) from rod assembly (4).
6.
Remove rod assembly (4) from lever (1).
7.
Remove rod assembly (4) from machine.
4
3
5
8
8.
Loosen nut (12).
9.
Remove rod (11) and nut (12) from link (10).
10.
Loosen nut (9).
11.
Remove rod end (6), nut (9), and link (10).
397-4381
10
9
6
11
12
0282 00-2
397-1419
TM 5-3805-261-23-2
0282 00
REMOVAL - CONTINUED
NOTE
Matchmark lever and fuel injection pump governor shaft to aid in aligning lever on fuel injection pump governor shaft during installation to fuel injection pump governor (17).
12.
Remove nut (14) and bolt (16).
13.
Remove lever (15) from fuel injection pump governor

shaft. (13).
13
17
14
15
16
397-1420
14.
For Type II machines, unscrew rear governor control

lever.
15.
Remove nut (21) and bolt (18) from inner-right side of

dash panel in engine compartment.
16.
Remove lever (19) from shaft (22) on inside of housing (23).
17.
Remove key (20) from shaft (22).
18.
Remove four bolts (26), washers (27), cover (25), and

19.
Support housing (23).
19
18
REAR GOVERNOR
CONTROL LEVER
20
21
22 (HIDDEN)
23
27
26
24
25
0282 00-3
397-1421
TM 5-3805-261-23-2
0282 00
REMOVAL - CONTINUED
20.
Remove two bolts (28), washers (29), housing (30),

and gasket (33). Discard gasket.
21.
Separate housing assembly (32) from cover (31).
32
31
30
28
29
33
397-1422
35
22.
Remove bolt (47) and nut (46) from actuator (45).
23.
Remove bolt (41), washer (40), and two springs (39).
24.
Separate rod end (42) and lever (48).
25.
Loosen nut (44).
26.
Remove rod end (42), actuator (45), and nut (44) from
cable end (37).
27.
Remove nut (43) from inside of housing (36).
28.
Loosen bolt (34).
29.
Move lever assembly (48) on shaft (35) to expose key

(38). Remove key from shaft.
30.
Remove shaft (35).
31.
Remove lever assembly (48) from housing (36).
36
34
37
48
47
38
46
39
45
41
44
43
0282 00-4
40
42
397-1423
TM 5-3805-261-23-2
0282 00
REMOVAL - CONTINUED
32.
Remove bolt (34) from lever assembly (48).
34
48
397-1424
33.
Remove housing (36) from machine.
NOTE
Removal of bearings from housing may cause destruction of bearings. Remove bearings only if inspection
indicates replacement is necessary.
34.
Inspect bearings (50 and 51). Replace if cracked, broken, or worn.
35.
Remove bearings (50 and 51), if necessary, from housing (36).
36.
Remove and discard two tie straps (52).
50
36
51
52
397-1425
0282 00-5
TM 5-3805-261-23-2
0282 00
REMOVAL - CONTINUED
37.
Remove four nuts (66), washers (67), three clips (68), two plates (69), and clamps (70) from front and rear of articulation area.
38.
Separate cable end (53) from left and right clamps (70) and pull cable through articulation area.
39.
Remove bolt (65), washer (71), and clip (72) from under right side of operators compartment.
40.
Remove bolt (64), washer (63), and clip assembly (62) from under right side of operators compartment. Leave clip
assembly mounted to hydraulic hose.
41.
Remove five bolts (61), washers (60), cover (59), and gasket (58). Discard gasket.
42.
43.
Separate rod end (57) and lever (54).
44.
Loosen nut (73).
45.
Remove rod end (57) and nut (73).
46.
Remove nut (74) from inside housing (55).
NOTE
For Type II machines, cable is divided between sections of machine. Either part of cable can be replaced
separately.
0282 00-6
TM 5-3805-261-23-2
0282 00
REMOVAL - CONTINUED
47.
Remove cable end (53) from machine.
54
55
53
56
57
75
58
74
59
60
73
72
61
71
70
62
65
63
397-2275
69
68
0282 00-7
64
67
66
TM 5-3805-261-23-2
0282 00
REMOVAL - CONTINUED
48.
Remove bolt (76).
49.
Remove three bolts (78) and washers (77).
50.
Pull lever assembly (54) and housing assembly (55)

away from engine.
51.
Remove housing assembly (55) from lever assembly

(54).
76
77
78
54
55
397-1427
52.
Remove shaft (79) and keys (84 and 80).
53.
Loosen bolt (85) and remove lever assembly (82).
80
79
55
NOTE
81
Removal of bearings from housing may

cause destruction of bearings. Remove
bearings only if inspection indicates
replacement is necessary.
84
54.
Inspect bearings (81 and 83). Replace if cracked, broken, or worn.
55.
Remove bearings (81 and 83), if necessary, from housing (55).
83
82
397-1428
56.
Remove bolt (85) from lever assembly (82).
85
82
397-1429
0282 00-8
TM 5-3805-261-23-2
0282 00
REMOVAL - CONTINUED
57.
Remove pedal stop bolt (92), nut (94), and washer (93).
58.
Remove nut (90), washer (89), and bolt (91).
59.
Remove nuts (88 and 86).
60.
Remove lever (87).
87
86
88
94
89
93
92
91
101
90
397-2276
61.
Remove pad (95) and boot (100) from right side of

floor in operators compartment.
62.
Remove treadle (99) and nut (98).
63.
Remove treadle (96) and boot (97).
95
96
100
99
97
98
397-1431
0282 00-9
TM 5-3805-261-23-2
0282 00
REMOVAL - CONTINUED
64.
Remove nut (103), washer (102), bolt (106), and rod

assembly (101) from bracket assembly (105) and rod
assembly (104), as a unit.
102 103
101
104
106
105
397-2277
101
65.
Loosen two nuts (108).
66.
Remove two rod ends (107) and nuts (108) from link
(109).
107
109
108
107
108
67.
68.
69.
70.
71.

Remove lever (111).
Remove nut (114), washer (115), and bolt (116) from
bracket assembly (113), and rod assembly (104).
Support bracket assembly (113) under right side of
operators compartment.
Remove two bolts (117), washers (118), and bracket
assembly (113).
104
111
112
110
113
114
115
118
117
0282 00-10
397-1433
116
397-1434
TM 5-3805-261-23-2
0282 00
REMOVAL - CONTINUED
72.
Remove key (119).
73.
74.
Remove lever (124) and key (126) from shaft (128).
75.
Remove shaft (128) from bracket (120).
76.
Remove two nuts (121) and bolts (122).
CAUTION
Removal of bushing may cause destruction of bearing. Remove bushing only if inspection indicates replacement is necessary.
77.
Inspect bushing (127). Replace if cracked, broken,

grooved, or worn.
78.
Remove bushing (127), if necessary, and bracket

(120).
119
120
121
122
123
128
124
127
79.
Remove and discard cotter pin (132) from right side of

operators control console (131) in operators compartment.
80.
Remove pin (129).
81.
Separate rod assembly (104) from handle (130).
82.
Remove rod assembly (104) from machine.
126
125
397-1435
130
129
104
132
131
0282 00-11
397-1436
TM 5-3805-261-23-2
0282 00
REMOVAL - CONTINUED
83.
Loosen nuts (136 and 138).
84.
Remove rod end (135), nut (136), rod end (133), nut
(138), boot (137), and rod (134).
135
104
134
133
136
137
397-1437
138
85.
Remove nut (144), washer (143), seat (142), six

springs (141), washer (139), handle assembly (140),
and disc (145).
140
139
141
142
143
145
144
397-1438
NOTE
Remove bearing only if inspection indicates replacement is necessary.
86.
Inspect bearing (150). Replace if cracked, broken, or

worn.
87.
Remove bearing (150), if necessary.
88.
Remove handle (148) from stud (149).
89.
Remove stud (149) from handle (147).
148
147
149
150
397-1439
0282 00-12
TM 5-3805-261-23-2
0282 00

INSTALLATION
1.
Install new bearing (150), if removed, to handle (147).
2.
Install stud (149) in handle (147).
3.
Install handle (148) on stud (149).
148
147
149
150
397-1439
4.
5.
Position disc (145), handle assembly (140), washer

(139), six springs (141), seat (142), and washer (143).
139
140
Install nut (144) loosely.
141
142
143
145
144
6.
Position boot (137) on rod (134).
7.
Install nut (138), rod end (133), nut (136), and rod end
(135) on ends of rod (134).
397-1438
135
104
134
133
136
137
138
0282 00-13
397-1437
TM 5-3805-261-23-2
0282 00
8.
Position rod assembly (104) through floor with rod

end (135) positioned to eye of handle (130).
9.
Install pin (129) and new cotter pin (132) at right side
of operators control console (131).
130
129
135
104
132
131
397-1436
10.
Install bushing (127), if removed, and bracket (120)

under right side of operators compartment.
11.
Install two bolts (122) and nuts (121) in bracket (120).
12.
Install shaft (128).
13.
Install key (126), lever (124), bolt (123), and nut

(125).
14.
Install key (119).
119
120
121
122
128
124
127
126
125
0282 00-14
123
397-1435
TM 5-3805-261-23-2
0282 00
15.
Install bracket assembly (113), two washers (118), and

bolts (117).
16.
Install bolt (116), rod assembly (104), washer (115),

and nut (114).
17.
Install lever (111).
18.
Install bolt (110) and nut (112).
104
111
112
113
114
110
115
116
118
117
397-1434
19.
101
Install two nuts (108) and rod ends (107) loosely on

link (109).
109
107
108
108
107
397-1433
0282 00-15
TM 5-3805-261-23-2
0282 00
20.
Position bracket assembly (105) with rod assembly

(104) on machine.
21.
Position rod assembly (101) on bracket assembly

(105).
22.
Install bolt (106), washer (102), and nut (103).
102 103
101
104
106
397-2277
105
23.
Install boot (97) and pedal (96) in right side of floor in

operators compartment.
24.
Install nut (98) and treadle (99).
25.
Install boot (100) and pad (95).
95
96
100
97
99
98
397-1431
26.
Install lever (87).
27.
Install nuts (88 and 86).
28.
Install bolt (91), lever (101) washer (89), and nut (90).
29.
Install pedal stop washer (93), nut (94), and bolt (92).
87
88
86
94
89
90
93
92
0282 00-16
91
101
397-2284
TM 5-3805-261-23-2
0282 00
30.
Install bolt (85) in lever (82).
85
82
397-1429
31.
Install new bearings (81 and 83), if removed.
32.
Install lever assembly (82) in housing (55).
33.
Install keys (84 and 80) and shaft (79).
80
79
55
84
81
83
82
397-1428
34.
Position housing assembly (55).
35.
Install three washers (77) and bolts (78).
36.
Install bolt (76).
76
77
78
54
55
397-1427
0282 00-17
TM 5-3805-261-23-2
0282 00
NOTE
For Type II machines, cable is divided between sections of machine. Either part of cable can be replaced
separately.
37.
Position cable end (53) through housing (55).
38.
Install nut (74).
39.
Install nut (73) and rod end (57) loosely.
40.
Align lever (82) and rod end (57).
41.
42.
Install clip (72), washer (71), and bolt (65), securing cable end (53) along with surrounding hose and clip assembly to
right side of frame.
55
53
82
57
75
73
56
74
72
71
65
397-2278
0282 00-18
TM 5-3805-261-23-2
0282 00
43.
Position cable end (53) in lower slot of right and left clamps (70) on rear and front of articulation area.
44.
Install one of two clamps (70), plates (69), two clips (68), washers (67), and nuts (66) loosely. Secure hoses to clips.
NOTE
Do not tighten nuts.
45.
Install one of two clamps (70), plates (69), two clips (68), washers (67), and nuts (66) loosely. Secure hoses to clips.
46.
Position cable end (53) from articulation area up to right side of engine compartment.
53
70
53
69
68
67
66
397-1443
0282 00-19
TM 5-3805-261-23-2
0282 00
47.
50
Install two new tie straps (52), and bearings (50 and
51), if removed. Drive new bearings on stamped side
into housing (36).
36
51
52
397-1425
48.
Install bolt (34) in lever (48).
34
48
397-1424
35
49.
Position shaft (35) in housing (36).
50.
Install key (38) in shaft (35).
51.
Install lever (48) on shaft (35) in housing (36).
52.
Install shaft (35) into housing (36).
53.
Tighten bolt (34).
54.
Position cable end (37) in housing (36).
55.
Install two nuts (43).
56.
Install nut (44), actuator (45), and rod end (42) on

cable end (37).
36
34
57.
Align lever (48) and rod end (42).
58.
Install two springs (39), washer (40), and bolt (41).
59.
Install nut (46) and bolt (47) in actuator (45).
37
48
47
38
39
46
40
45
41
44
43
0282 00-20
42
397-1423
TM 5-3805-261-23-2
0282 00
60.
Position housing assembly (32), new gasket (33), and

housing (30) on cover (31).
61.
Install two washers (29) and bolts (28).
32
31
30
28
29
33
397-1422
62.
Install key (20) in shaft (22).
63.
For Type II machines, install rear governor control

lever.
64.
Install lever (19) on shaft (22).
65.
66.
Install new gasket (24), cover (25), four washers (27),

and bolts (26) to housing (23).
19
18
REAR GOVERNOR
CONTROL LEVER
20
21
22 (HIDDEN)
23
27
26
24
25
0282 00-21
397-1421
TM 5-3805-261-23-2
0282 00
67.
Align fuel injection pump governor shaft (13) and

lever (15) with matchmarks on fuel injection pump
governor (17).
68.
13
17
14
15
16
69.
Install nut (9), rod end (6), nut (12), and rod (11)
loosely on link (10).
397-1420
10
9
6
11
397-1419
12
70.
Position rod assembly (4).
NOTE
Do not bend back two cotter pins at this
time.
71.
72.
Install pin (3) and new cotter pin (2) to rod assembly
(4) and lever (1).
Install rod end (6) to rod assembly (4) and lever (8).
4
8
0282 00-22
397-1418
TM 5-3805-261-23-2
0282 00
73.
Tighten nut (73) securing rod end (57) in housing (55) under right side of operators compartment.
74.
Install new gasket (58), cover (59), five washers (60), and bolts (61).
75.
Position clip assembly (72) with hydraulic hose on cover (59). Install four washers (71) and bolts (66).
76.
77.
Tighten four bolts (66) at front and rear of articulation area.
55
58
59
60
73
61
57
72
71
62
66
63
64
397-1446
0282 00-23
TM 5-3805-261-23-2
0282 00
ADJUSTMENT
1.
Disconnect rod assembly (4) from governor lever (8).
2.
Position governor lever (8) in low idle position.
3.
Start engine and ensure low idle RPMs are within specifications.
4.
Shut off engine.
5.
Disconnect cable end (53) from housing (55).
HIGH IDLE
55
15.25 IN.
(38.7 CM)
SHUTOFF
0.75 IN.
(19.0 MM)
8
7
LOW IDLE
53
397-2280
6.
Adjust rod assembly (4) to 15.25 in. (38.7 cm).
7.
Connect rod assembly (4) to governor lever (8).
8.
0282 00-24
TM 5-3805-261-23-2
0282 00
9.
Disconnect cable end (53) from housing (23) at engine.
10.
Disconnect rod (101).
11.
Adjust length between bolt holes of rod (101) to 13.81 in. (35.1 cm).
NOTE
On machines with high detent force, when going from low idle to shut off, distance between treadle lever
and floor plate can be increased to 2 in. (5 cm) to allow for needed cable stretch.
12.
Install rod (101) and adjust linkage low idle stop (151) so that treadle lever (96) is 1.5 in. (3.8 cm) below floor plate.
This is low idle position of pedal (96).
13.
Adjust length between pin holes of rod (104) to 17.53 in. (44.5 cm). When governor control linkage is against low idle
stop (151), governor control handle (152) will be positioned approximately 30 degrees from vertical.
152
SHUT-OFF
0.38 IN.
(9.7 MM)
ENCLOSED ROPS
0.19 IN.
(4.8 MM)
OPEN ROPS
104
151
LOW IDLE
HIGH IDLE
96
1.5 IN.
(3.8 CM)
53
0.75 IN.
(19.0 MM)
23
101
0282 00-25
397-2281
TM 5-3805-261-23-2
0282 00
14.
Adjust position of cable end (53) to housing (23) and housing (55). Ensure shoulder of each cable end is approximately
0.75 in. (19 mm) from face of housing.
15.
At engine, set governor lever (8) to a 52-degree angle for the low idle position.
16.
With governor lever (8) and governor control handle (152) in low idle position, adjust cable ends to allow for connection
to levers inside housings (23) and (55).
17.
Check engine shutoff by pulling up on accelerator treadle. There should be a distinct detent for off position.
HIGH IDLE
55
15.25 IN.
(38.7 CM)
SHUTOFF
0.75 IN.
(19.0 MM)
8
LOW IDLE
53
397-2280
0282 00-26
TM 5-3805-261-23-2
0282 00
NOTE
Low idle RPM can be adjusted at governor. Do NOT change high idle RPM by adjusting governor.
18.
19.
20.
21.
22.
Place governor control linkage (153) in low idle position and start engine.
Move governor control lever (8) to the high idle position. Adjust governor control linkage (153) high idle stop and pedal
lever (154) high idle stop. Ensure a 0.12 in. (3 mm) clearance between levers and stops when governor control lever is in
high idle position. Stop engine by pulling up on accelerator pedal (96).
Put accelerator pedal (96) in low idle position.
For machines with open ROPS, adjust decelerator pedal (99). Set top of pedal to 0.19 in. (4.8 mm) above floor plate. For
machines with enclosed ROPS, set top of decelerator pedal to 0.38 in. (9.7 mm) above floor plate.
Position treadle assembly to high idle. Adjust accelerator treadle (96) to provide 2.38 in. (6.1 cm) clearance between
bottom of treadle and floor plate.
152
LOW IDLE
SHUTOFF
99
0.12 IN. (3.0 MM)
96
HIGH
IDLE
2.38 +/ - 0.12 IN.
(6.1 +/- 0.3 CM.)
153
154
0282 00-27
0.12 IN. (3.0 MM)
397-2282
TM 5-3805-261-23-2
0282 00
23.
Install two new tie straps (52) around cable end (37)
and governor switch wires (155).
24.
Install new gasket (24), cover (25), four washers (27),

and bolts (26).
25
37
24
27
52
26
397-2283
155
25.
Install governor switch (WP 0088 00).
END OF WORK PACKAGE
0282 00-28
TM 5-3805-261-23-2
TURBOCHARGER REPLACEMENT
0283 00

INITIAL SETUP
Maintenance Level
References
WP 0020 00
Direct Support

0348 00)

Materials/Parts
Antiseize compound (Item 6, WP 0349 00)
Engine off (TM 5-3805-261-10)
Oil, lubricating (Items 26, 27, or 30, WP 0349 00)

Turbocharger oil lines removed (WP 0033 00)

Turbocharger air lines removed (WP 0039 00)
Turbocharger exhaust elbow removed (WP 0040

00)
Gasket
0283 00-1
TM 5-3805-261-23-2
TURBOCHARGER REPLACEMENT - CONTINUED
0283 00
REMOVAL
1.
Remove four nuts (4), bolts (2), bolt (5), and nut (6).
2.
Remove turbocharger (1) and gasket (3). Discard gasket.
1
2
3
397-2227

INSTALLATION
1.
Install new gasket (3) and turbocharger (1).
2.
Coat threads of nut (6), bolt (5), four bolts (2), and nuts (4) with antiseize compound and install. Tighten bolts to 40 lbft (54 Nm).
3.
Install turbocharger exhaust elbow (WP 0040 00).
4.
Install turbocharger air lines (WP 0039 00).
5.
Install return turbocharger oil line (WP 0033 00).
6.
Pour 1/2 cup clean oil into turbocharger oil supply port (7).
7.
Install supply turbocharger oil line (WP 0033 00).
END OF WORK PACKAGE
0283 00-2
TM 5-3805-261-23-2
ELECTRONIC MONITORING SYSTEM (EMS) PANEL REPAIR
0284 00

Disassembly, Cleaning and Inspection, Assembly
INITIAL SETUP
References
Maintenance Level
Direct Support
WP 0021 00


0348 00)
Materials/Parts
Silicone compound (Item 41, WP 0349 00)

Sealing compound (Item 39, WP 0349 00)
Engine off (TM 5-3805-261-10)
Washer, key (9)
Electronic monitoring system panel removed (WP

0069 00)
Washer, seal
DISASSEMBLY
1.
Remove plug (5) and preformed packing (6) from

cover (3). Discard preformed packing.
2.
Remove four stud bolts (4), cover (3), and preformed

packing (7). Discard preformed packing.
3.
Remove and discard seal washer (2) from connector

(1).
1
2
7
3
6
5
397-4083
0284 00-1
TM 5-3805-261-23-2
ELECTRONIC MONITORING SYSTEM (EMS) PANEL REPAIR - CONTINUED
0284 00
4.
Remove nine screws (9), key washers (10), magnet

(11), and housing (8). Discard key washers.
11
10
9
397-4084

ASSEMBLY
1.
Apply silicone (heat transfer) compound to corner of magnet (11) where transistor and heat sink are located. Apply
thread sealant to nine screws (9). Install housing (8), magnet, nine new key washers (10), and screws.
2.
Install new seal washer (2) on connector (1). Tighten

to 72 lb-in. (8 Nm).
3.
Install new preformed packing (7), cover (3), and four

stud bolts (4). Tighten stud bolts to 48 lb-in. (5 Nm).
4.
Install new preformed packing (6) and plug (5).
1
2
7
3
6
5
397-4083
5.
Install EMS panel (WP 0069 00).
6.
Connect battery cables (WP 0125 00).
END OF WORK PACKAGE

0284 00-2
TM 5-3805-261-23-2
REAR SIGNAL LIGHT AND BACKUP ALARM WIRING HARNESS REPLACEMENT
0285 00

INITIAL SETUP
Maintenance Level
Direct Support

Materials/Parts
Strap, tie (Item 43, WP 0349 00)
Engine off (TM 5-3805-261-10)

Engine screen doors opened (TM 5-3805-261-10)
References
WP 0021 00
Radiator grille removed (WP 0054 00)
0285 00-1
TM 5-3805-261-23-2
REAR SIGNAL LIGHT AND BACKUP ALARM WIRING HARNESS REPLACEMENT - CONTINUED
0285 00
REMOVAL
1.
Remove three nuts (8), washers (10), and clips (1).
NOTE
Tag and note routing of wiring harnesses
2.
Disconnect rear signal light and backup alarm wiring

harness (9) from main wiring harness (7).
3.
4.
Cut and discard tie strap (4).
5.
Disconnect rear signal light and backup alarm wiring

harness (9) from rear work light wiring harness (3).
10
9
8
7
397-4085
6.
Disconnect two wire assemblies (17) from rear signal light and backup alarm wiring harness (9).
7.
Remove rear signal light and backup alarm wiring harness (9) from clip (19).
8.
Disconnect wire assembly (12) from rear signal light and backup alarm wiring harness (9).
9.
10.
Disconnect wire assembly (11) from rear signal light

and backup alarm wiring harness (9).
11.
12.

13.
14.

15.
Remove rear signal light and backup alarm wiring harness (9) from machine.
12 13
15
14
16
11
19
18
9
17
397-4086

1.
2.
Repair rear signal light and backup alarm wiring harness, if necessary (WP 0021 00).
0285 00-2
TM 5-3805-261-23-2
REAR SIGNAL LIGHT AND BACKUP ALARM WIRING HARNESS REPLACEMENT - CONTINUED
0285 00
INSTALLATION
CAUTION
Do not position rear signal light and backup alarm wiring harness against any rough surface. Failure to follow this procedure may cause chafing.
NOTE
Route rear signal light and backup alarm wiring harness exactly as it was removed.
1.
Position rear signal light and backup alarm wiring harness (9) in machine.
2.
Connect wire assembly (16) to rear signal light and backup alarm wiring harness (9).
3.
Install rear signal light and backup alarm wiring harness (9) into clip (14).
4.
5.
6.
7.
Install rear signal light and backup wiring harness (9) into clip (18).
8.
9.
10.
Connect two wire assemblies (17) to rear signal light and backup alarm wiring harness (9).
11.
Connect rear signal light and backup alarm wiring harness (9) to rear work light wiring harness (3).
12.
Install new tie strap (4).
13.
14.
Connect rear signal light and backup alarm wiring harness (9) to main wiring harness (7).
15.
Install three clips (1), washers (10), and nuts (8).
16.
17.
Install radiator grill (WP 0054 00).
18.
Close engine screen doors (TM 5-3805-261-10).
END OF WORK PACKAGE
0285 00-3/(-4 Blank)
TM 5-3805-261-23-2
MAIN WIRING HARNESS REPLACEMENT
0286 00

INITIAL SETUP
Maintenance Level
References - Continued
WP 0096 00
Direct Support
WP 0103 00
WP 0108 00
WP 0113 00
WP 0114 00
Materials/Parts
WP 0252 00

References
WP 0021 00
Engine off (TM 5-3805-261-10)
WP 0050 00
WP 0066 00
Left and right side engine panels removed (WP

0182 00)
WP 0067 00
Left and right side panels removed from operators

panel console (WP 0093 00)
WP 0069 00
Operators panel console base removed (WP 0328

00)
WP 0093 00
0286 00-1
TM 5-3805-261-23-2
MAIN WIRING HARNESS REPLACEMENT - CONTINUED
0286 00
REMOVAL
NOTE
Tag and note routing of wiring harness before disconnecting to aid in installation.
1.
Disconnect main wiring harness (15) from ether start valve (1) (WP 0050 00), alternator (14) (WP 0066 00), starting
motor (12) (WP 0067 00), air pressure and hourmeter gauges (3) (WP 0252 00), oil pressure and hourmeter switches (2)
(WP 0113 00), ether start temperature switch (4) (WP 0114 00), fuse box (11) (WP 0096 00), stop light switch (9) (WP
0108 00), blade float limit switch (CCE machine) (8) (WP 0093 00), dimmer switch (7) (WP 0103 00), and EMS panel
(6) (WP 0069 00).
2.
Remove clips (5), clamps (10), and tie straps (13). Discard tie straps.
3.
Remove main wiring harness (15) from machine.
1
2
15
4
6
14
7
13
12
9
11
8
10
0286 00-2
397-4087
TM 5-3805-261-23-2
MAIN WIRING HARNESS REPLACEMENT - CONTINUED
0286 00

Repair main wiring harness, if necessary (WP 0021 00).
INSTALLATION
CAUTION
Do not position main wiring harness against any rough surface. Failure to follow this procedure may cause
chafing.
NOTE
Route main wiring harness exactly as it was removed.
1.
Position main wiring harness (15) on machine.
2.
Connect main wiring harness (15) to EMS panel (6) (WP 0069 00), dimmer switch (7) (WP 0103 00), blade float limit
switch (CCE machine) (8) (WP 0093 00), stop light switch (9) (WP 0108 00), fuse box (11) (WP 0096 00), ether start
temperature switch (4) (WP 0114 00), oil pressure and hourmeter switches (2) (WP 0113 00), air pressure and hourmeter
gauges (3) (WP 0252 00), starting motor (12) (WP 0067 00), alternator (14) (WP 0066 00), and ether start valve (1) (WP
0050 00).
3.
Install new tie straps (13), clamps (10), and clips (5).
4.
Install operators panel console base (WP 0328 00).
5.
Install left and right side panels on operators panel console (WP 0193 00).
6.
Install left and right side engine panels (WP 0182 00).
7.
END OF WORK PACKAGE
0286 00-3/(-4 Blank)
TM 5-3805-261-23-2
MAIN BLACKOUT LIGHT WIRING HARNESS REPLACEMENT
0287 00

INITIAL SETUP
Maintenance Level
Direct Support
Tool kit, general mechanics (Item 89, WP 0348)
Engine off (TM 5-3805-261-10)
Materials/Parts
Operators console cover removed (WP 0082 00)
References
WP 0021 00
WP 0096 00
WP 0101 00
WP 0102 00
WP 0117 00
WP 0193 00
0287 00-1
TM 5-3805-261-23-2
MAIN BLACKOUT LIGHT WIRING HARNESS REPLACEMENT - CONTINUED
0287 00
REMOVAL
NOTE
1.
2.
3.
Disconnect main blackout light wiring harness (4) from magnetic switch (2) (WP 0102 00), vehicle light switch (3) (WP
0101 00), blackout/stop light switch (6) (WP 0117 00), fuse box (7) (WP 0096 00), and junction block (WP 0193 00).
Remove clips (1), clamps (5), and tie straps (8). Discard tie straps.
Remove main blackout light wiring harness (4) from machine.
3
2
397-4088

INSTALLATION
CAUTION
Do not position main blackout light wiring harness against any rough surface. Failure to follow this procedure may cause chafing.
NOTE
Route main blackout light wiring harness exactly as it was removed.
1.
Position main blackout light wiring harness (4) on machine.
2.
Install main blackout light wiring harness (4) to junction block (9) (WP 0193 00), fuse box (7) (WP 0096 00), blackout/
stop light switch (6) (WP 0117 00), vehicle light switch (3) (WP 0101 00), and magnetic switch (2) (WP 0102 00).
3.
Install new tie straps (8), clamps (5), and clips (1).
4.
Install operators console cover (WP 0082 00).
5.
END OF WORK PACKAGE

0287 00-2
TM 5-3805-261-23-2
FRONT BLACKOUT LIGHT WIRING HARNESS REPLACEMENT
0288 00

INITIAL SETUP
Maintenance Level
References
WP 0021 00
Direct Support


Materials/Parts

Engine off (TM 5-3805-261-10)
Lockwasher (2)
Left side frame cover removed (WP 0179 00)
0288 00-1
TM 5-3805-261-23-2
FRONT BLACKOUT LIGHT WIRING HARNESS REPLACEMENT - CONTINUED
0288 00
REMOVAL
NOTE
Tag and note routing of wiring harnesses before disconnecting to aid in installation.
1.
Disconnect front blackout light wiring harness (5) from back of front blackout light (1).
2.
Remove nut (9).
3.
Disconnect wire assembly (10) from bottom of front blackout light (1).
4.
Remove lockwasher (11) and front blackout light (1). Discard lockwasher.
5.
Remove and discard seven tie straps (2) from left-front frame of machine.
6.
7.
Disconnect wire assembly (8).
8.
Remove and discard lockwasher (12).
9.
Remove front blackout light wiring harness (5) and main blackout light wiring harness (4) from clip (3).
10.
Disconnect front blackout light wiring harness (5) from main blackout light wiring harness (4).
11.
Remove front blackout light wiring harness (5) from machine.
12
11
10
9
397-4089

0288 00-2
TM 5-3805-261-23-2
FRONT BLACKOUT LIGHT WIRING HARNESS REPLACEMENT - CONTINUED
0288 00
INSTALLATION
CAUTION
Do not position front blackout light wiring harness against any rough surface. Failure to follow this procedure may cause chafing.
NOTE
Route front blackout light wiring harness exactly as it was removed.
1.
Position front blackout light wiring harness (5) on machine.
2.
Connect front blackout light wiring harness (5) to main blackout light wiring harness (4) and attach to clip (3).
3.
Install new lockwasher (12) on left-front frame of machine.
4.
Connect wire assembly (8).
5.
6.
Install seven new tie straps (2).
7.
Install front blackout light (1) and new lockwasher (11).
8.
Connect wire assembly (10) to bottom of front blackout light (1).
9.
Install nut (9).
10.
Connect front blackout light wiring harness (5) to back of front blackout light (1).
11.
Install left side frame cover (WP 0179 00).
12.
END OF WORK PACKAGE
0288 00-3/(-4 Blank)
TM 5-3805-261-23-2
REAR BLACKOUT LIGHT WIRING HARNESS REPLACEMENT
0289 00

INITIAL SETUP
Maintenance Level
Direct Support
Materials/Parts
Engine off (TM 5-3805-261-10)
Right and left engine side screen doors opened (WP

0055 00)
References
Baffles removed (WP 0053 00)

Grille removed (WP 0054 00)
WP 0021 00
REMOVAL
NOTE
Tag and note routing of wiring harnesses

1.
Disconnect rear blackout light wiring harness (2) from

right blackout light (1).
2.
Remove two bolts (13), washers (14), and small clips

(15).
3.
Remove two bolts (10), washers (11), and large clips

(12).
4.
2
1
15
5.
Remove two bolts (5), washers (4), and small clips (6).
6.
Remove two bolts (7), washers (8), and large clips (9).
14
Disconnect rear blackout light wiring harness (2) from

left blackout light (3).
13
12
11
0289 00-1
10
397-4090
TM 5-3805-261-23-2
REAR BLACKOUT LIGHT WIRING HARNESS REPLACEMENT - CONTINUED
0289 00
REMOVAL - CONTINUED
7.
Remove three nuts (20), washers (16), and clips (21).
8.
Remove and discard tie strap (17).
9.
Remove rear blackout light wiring harness (2) from clip (18).
10.
Remove rear blackout light wiring harness (2) from main wiring harness (19).
11.
Remove rear blackout light wiring harness (2) from machine.

INSTALLATION
CAUTION
Do not position rear blackout light wiring harness against any rough surface. Failure to follow this procedure
may cause chafing.
NOTE
16
Route rear blackout light wiring harness

exactly as it was removed.
1.
Position rear blackout light wiring harness (2) on

machine.
2.
Connect rear blackout light wiring harness (2) to main

blackout light wiring harness.
3.
Install rear blackout light wiring harness (2) into clip

(18).
4.
Install new tie strap (17).
5.
Install three clips (21), washers (16), and three nuts

(20).
0289 00-2
17
2
18
21
20
19
397-4091
TM 5-3805-261-23-2
REAR BLACKOUT LIGHT WIRING HARNESS REPLACEMENT - CONTINUED
0289 00
6.
Install two large clips (9), washers (8), and bolts (7).
7.
Install two small clips (6), washers (4), and bolts (5).
8.
Connect rear blackout light wiring harness (2) to left

blackout light (3).
9.
Install two large clips (12), washers (11), and bolts

(10).
10.
Install two small clips (15), washers (14), and bolts

(13).
11.
Connect rear blackout light wiring harness (2) to right

blackout light (1).
3
4
2
1
15
14
13
12
11
12.
Install grille (WP 0054 00).
13.
Install baffles (WP 0053 00).
14.
Close right and left side engine screen doors (WP 0055 00).
15.
END OF WORK PACKAGE
0289 00-3/(-4 Blank)
10
397-4090
TM 5-3805-261-23-2
SUPPLEMENTAL STEERING MAIN WIRING HARNESS REPLACEMENT
0290 00

INITIAL SETUP
Maintenance Level
Direct Support
Engine off (TM 5-3805-261-10)
Materials/Parts

0182 00)
References
WP 0021 00
Steering control console plates removed (WP 0197

00 or WP 0198 00)
WP 0066 00
WP 0076 00
WP 0078 00
WP 0089 00
WP 0099 00
WP 0102 00
WP 0112 00
WP 0131 00
0290 00-1
TM 5-3805-261-23-2
SUPPLEMENTAL STEERING MAIN WIRING HARNESS REPLACEMENT - CONTINUED
0290 00
REMOVAL
NOTE
Tag and note routing of wire harnesses before disconnecting to aid in installation.
1.
Disconnect supplemental steering main wiring harness (3) from electronic control (4) (WP 0089 00), ground (2), alternator wire assembly (1) (WP 0066 00), magnetic switch (5) (WP 0102 00), fuse box (13) (WP 0096 00), steering pressure switch (12) (WP 0112 00), dump valve harness (11) (WP 0131 00), monitor panel harness (7), indicator light (8)
(WP 0078 00), and manual switch (6) (WP 0074 00).
2.
Remove clips/clamps (10) and tie straps (9). Discard tie straps.
NOTE
For Type II machines, wiring harness is divided between sections of machine.
3.
Remove supplemental steering main wiring harness (3) from machine.
5
4
6
7
2
9
12
13
10
11
0290 00-2
397-4092
TM 5-3805-261-23-2
SUPPLEMENTAL STEERING MAIN WIRING HARNESS REPLACEMENT - CONTINUED
0290 00
INSTALLATION
CAUTION
Do not position supplemental steering main wiring harness against any rough surface. Failure to follow this
procedure could cause chafing.
NOTE
Route supplemental steering main wiring harness exactly as it was removed.
1.
Position supplemental steering main wiring harness (3) from machine.
2.
Disconnect supplemental steering main wiring harness (3) from electronic control (4) (WP 0089 00), ground (2), alternator wire assembly (1) (WP 0066 00), magnetic switch (5) (WP 0102 00), fuse box (13) (WP 0096 00), steering pressure switch (12) (WP 0112 00), dump valve harness (11) (WP 0131 00), monitor panel harness (7), indicator light (8)
(WP 0078 00), and manual switch (6) (WP 0076 00).
3.
Install new tie straps (9) and clips/clamps (10).
4.
Install steering control console plates (WP 0197 00 or WP 0198 00).
5.
6.
END OF WORK PACKAGE
0290 00-3/(-4 Blank)
TM 5-3805-261-23-2
ELECTRONIC MONITORING SYSTEM (EMS) MAIN WIRING HARNESS REPLACEMENT
0291 00

INITIAL SETUP
Maintenance Level
WP 0112 00
Direct Support
WP 0113 00
WP 0114 00
WP 0115 00
WP 0114 00
Materials/Parts
WP 0119 00

References
WP 0021 00
WP 0066 00
WP 0067 00
Engine off (TM 5-3805-261-10)
WP 0069 00
WP 0070 00

0182 00)
WP 0071 00
Steering control console plates removed (WP 0197

00 or WP 0198 00)
WP 0086 00
0291 00-1
TM 5-3805-261-23-2
ELECTRONIC MONITORING SYSTEM (EMS) MAIN

WIRING HARNESS REPLACEMENT - CONTINUED
0291 00
REMOVAL
NOTE
1.
Disconnect EMS wiring harness (1) from test switch (8) (WP 0070 00), lamp (9) (WP 0071 00), EMS panel (7) (WP
0069 00), supplemental steering (10) (WP 0086 00), air pressure switches (12) (WP 0112 00), fuse box (13) (WP 0096
00), warning horn (6) (WP 0119 00), coolant temperature switch (5) (WP 0114 00), engine oil pressure switch (2) (WP
0113 00), hourmeter switch (3) (WP 0113 00), hydraulic oil temperature switch (4) (WP 0116 00), fuel pressure switch
(14) (WP 0115 00), starting motor (15) (WP 0067 00), alternator (16) (WP 0066 00), and jumper wire (17).
2.
Remove clips/clamps (11) and tie straps. Discard tie straps.
NOTE
For Type II machines, wiring harness is divided between sections of machine.
3.
Remove EMS wiring harness (1) from machine.
5
1
2
17
3
4
16
10
15
6
7
12
14
13
11
0291 00-2
397-4093
TM 5-3805-261-23-2
ELECTRONIC MONITORING SYSTEM (EMS) MAIN

WIRING HARNESS REPLACEMENT - CONTINUED
0291 00

INSTALLATION
CAUTION
Do not position electrical monitor wiring harness against any rough surface. Failure to follow this procedure
could cause chafing.
NOTE
Route electrical monitor wiring harness exactly as it was removed.
1.
Position EMS wiring harness (1) on machine.
2.
Connect electrical monitor wiring harness (1) to jumper wire (17), alternator (16) (WP 0062 00), starting motor (15)
(WP 0067 00), fuel pressure switch (14) (WP 0115 00), hydraulic oil temperature switch (4) (WP 0116 00), hourmeter
switch (3) (WP 0113 00), engine oil pressure switch (2) (WP 0113 00), coolant temperature switch (5) (WP 0114 00),
warning horn (6) (WP 0119 00), fuse box (13) (WP 0096 00), air pressure switches (12) (WP 0112 00), supplemental
steering (10) (WP 0086 00), EMS panel (7) (WP 0069 00), lamp (9) (WP 0071 00), and test switch (8) (WP 0070 00).
3.
Install new tie straps and clips/clamps (11).
4.
Install steering control console plates (WP 0197 00 or WP 0198 00).
5.
6.
END OF WORK PACKAGE
0291 00-3/(-4 Blank)
TM 5-3805-261-23-2
CAB MAIN WIRING HARNESS REPLACEMENT (CCE MACHINE)
0292 00

INITIAL SETUP
Maintenance Level
WP 0206 00
Direct Support
WP 0207 00
WP 0208 00

Materials/Parts

References
WP 0021 00
Engine off (TM 5-3805-261-10)
WP 0097 00
WP 0104 00
Cab switch panel removed (WP 0085 00)
WP 0107 00
Windshield washer removed (WP 0209 00)
0292 00-1
TM 5-3805-261-23-2
CAB MAIN WIRING HARNESS REPLACEMENT (CCE MACHINE) - CONTINUED
0292 00
REMOVAL
1.
Remove two plates behind right cab door hinge.
NOTE
2.
Disconnect cab main wiring harness (1) from rear wiper switch (WP 0208 00).
3.
Disconnect cab main wiring harness (1) from cab fuse box (10) (WP 0095 00), cab signal lights (2 and 7) (WP 0107 00),
headlights (3 and 6) (WP 0104 00), upper wiper motor (4) (WP 0207 00), lower wiper motor (5) (WP 0206 00), and wiring harnesses.
4.
Remove mounting clips (9) and harness clip (8).
5.
Remove cab main wiring harness (1) from machine.
2
3
4
1
10
397-4094

Repair cab main wiring harness, if necessary (WP 0021 00).
0292 00-2
TM 5-3805-261-23-2
CAB MAIN WIRING HARNESS REPLACEMENT (CCE MACHINE) - CONTINUED
0292 00
INSTALLATION
CAUTION
Do not position cab main wiring harness against any rough surface. Failure to follow this procedure could
cause chafing.
NOTE
Route cab main wiring harness exactly as it was removed.
1.
Position cab main wiring harness (1) on machine.
2.
Connect cab main wiring harness (1) to wiring harnesses, lower wiper motor (5) (WP 0206 00), upper wiper motor (4)
(WP 0207 00), headlights (6 and 3) (WP 0104 00), cab signal lights (7 and 2) (WP 0107 00), and cab fuse fox (10) (WP
0095 00).
3.
Install harness clip (8) and mounting clips (9).
4.
Connect cab main wiring harness (1) to rear wiper switch (WP 0208 00).
5.
Install two plates behind right cab door hinge.
6.
Install windshield washer (WP 0209 00).
7.
Install cab switch panel (WP 0085 00).
8.
END OF WORK PACKAGE
0292 00-3/(-4 Blank)
TM 5-3805-261-23-2
REAR WIPER WIRING HARNESS REPLACEMENT (CCE MACHINE)
0293 00

INITIAL SETUP
Maintenance Level
Direct Support

Materials/Parts
Engine off (TM 5-3805-261-10)

References
Rear wiper motor access cover removed (WP 0208

00)
WP 0021 00
REMOVAL
NOTE
Tag and note routing of wire assemblies before disconnecting to aid in installation.
1.
Disconnect five wire assemblies (1) from motor (3).
2.
Remove rear wiper wiring harness (2).
1
1
2
3
397-4095
0293 00-1
TM 5-3805-261-23-2
REAR WIPER WIRING HARNESS REPLACEMENT (CCE MACHINE) - CONTINUED
0293 00

Repair rear wiper wiring harness, if necessary (WP 0021 00).
INSTALLATION
1.
Position rear wiping wiring harness (2).
2.
Connect five wire assemblies (1) to motor (3).
1
1
2
3
397-4095
3.
Install rear wiper motor access cover (WP 0208 00).
4.
END OF WORK PACKAGE
0293 00-2
TM 5-3805-261-23-2
TRANSMISSION, ADAPTER, AND DIFFERENTIAL REPLACEMENT
0294 00

INITIAL SETUP
Maintenance Level
Direct Support
0348 00)
Anti-articulation pin installed (TM 5-3805-261-10)

Coolant drained from cooling system (WP 0065 00)
Oil drained from transmission (WP 0147 00)
Engine hood removed (WP 0181 00)

0182 00)
Materials/Parts
Packing, preformed
Fuel tank removed (WP 0044 00)

Radiator hoses removed (WP 0057 00)
Personnel Required
Transmission control cables removed from transmission housing (WP 0152 00)
Two
References
Transmission oil filter base removed (WP 0153 00)
WP 0020 00
Transmission oil lines removed (WP 0155 00)
Remote steer air valves removed (Type II machine)

(WP 0315 00)
Transmission oil pump removed (WP 0297 00)
Differential lock line disconnected from transmission relief valve (WP 0306 00)
Drive axles removed (WP 0307 00)
Engine off (TM 5-3805-261-10)
0294 00-1
Parking brake actuator and valve removed (WP

0312 00)
TM 5-3805-261-23-2
TRANSMISSION, ADAPTER, AND DIFFERENTIAL REPLACEMENT - CONTINUED
0294 00
REMOVAL
1.
Attach lifting device to two lifting eyes (3) on transmission (4).
2.
Remove 12 bolts (1) and washers (2) between adapter

and flywheel housing.
LIFTING DEVICE
3
397-4123
NOTE
Perform the following steps only if transmission must be removed.
3.
Remove 10 nuts (5) and washers (6) between transmission (4) and drive axle assembly.
0294 00-2
4
397-4124
TM 5-3805-261-23-2
0294 00
REMOVAL - CONTINUED
WARNING
Use extreme caution when handling heavy parts. Provide adequate support and use assistance during procedure. Keep clear of heavy parts supported only by lifting device. Failure to follow this warning may cause
NOTE
Transmission weighs 2,000 lb (907 kg).

4.
Use lifting device to remove transmission (4) and

adapter (7) from machine.
5.
Place transmission (4) and adapter (7) on stand.
6.
Remove and discard preformed packing (8)
7.
Remove lifting device from two lifting eyes (3).
4
397-4125

0294 00-3
TM 5-3805-261-23-2
0294 00
INSTALLATION
NOTE
Elevate two rear wheels, right or left.
1.
Attach lifting device to two lifting eyes (3) on transmission (4).
LIFTING DEVICE
3
NOTE
397-4123
If splines do not line up, raise one wheel

and rotate until the two splines are in line.
2.
Install preformed packing (8).
3.
Use lifting device to install transmission (4) and

adapter (7) in machine. Fit transmission splines in
transmission into splines in differential.
4
397-4125
0294 00-4
TM 5-3805-261-23-2
0294 00
4.
Rotate oil pump shaft to align splines of transmission

adapter gear to engine flywheel.
5.
Install 10 washers (6) and nuts (5) over studs between

transmission (4) and drive axle assembly.
6.
Install 12 washers (2) and bolts (1) between adapter

and flywheel housing.
7.
Remove lifting device from lifting eyes (3) of transmission (4).
397-4124
LIFTING DEVICE
3
4
8.
Install parking brake actuator and valve (WP 0312 00).
9.
Install drive axles (WP 0307 00).
10.
Connect differential lock line to transmission relief valve (WP 0306 00).
11.
Install transmission oil pump (WP 0297 00).
12.
Install remote steer air valves (Type II machine) (WP 0315 00).
13.
Install transmission oil lines (WP 0155 00).
14.
Install transmission oil filter base (WP 0153 00).
15.
Install transmission control cables to transmission housing (WP 0152 00).
16.
Install radiator hoses (WP 0057 00).
17.
Install fuel tank (WP 0044 00).

0294 00-5
397-4123
TM 5-3805-261-23-2

18.
19.
Install engine hood (WP 0181 00).
20.
Fill transmission with oil (WP 0147 00).
21.
Fill cooling system with coolant (WP 0065 00).
22.
Remove and store anti-articulation pin (TM 5-3805-261-10).
23.
Start engine. Check for leaks.
END OF WORK PACKAGE
0294 00-6
0294 00
TM 5-3805-261-23-2
ENGINE-TO-TRANSMISSION ADAPTER REPLACEMENT
0295 00

INITIAL SETUP
Personnel Required
Maintenance Level
Direct Support
Two
References

0348 00)
WP 0020 00


Materials/Parts
Engine off (TM 5-3805-261-10)
Gasket
Lockwasher (12)
Transmission, adapter, and differential removed

(WP 0294 00)
Wood blocks
REMOVAL
1.
2.
Remove plug (3) and gasket (2) from transmission (4).

Discard gasket.
2
4
0295 00-1
3
397-4129
TM 5-3805-261-23-2
ENGINE-TO-TRANSMISSION ADAPTER REPLACEMENT - CONTINUED
0295 00
REMOVAL - CONTINUED
BOLTS
LINK BRACKETS
WARNING
Use extreme caution when handling heavy
parts. Provide adequate support and use
assistance during procedure. Ensure that
any lifting device used is in good condition and of suitable load capacity. Keep
clear of heavy parts supported only by lifting device. Failure to follow this warning
may cause injury or death to personnel.
NOTE
Housing weighs 84 lb (38 kg).
3.
Install two link brackets and 3/8-16-2B bolts in holes

at top of housing (5).
397-4130
4.
Attach sling to housing (5) and take up slack.
5.
Remove 12 bolts (6) and lockwashers (7).
6.
Remove housing (5) from transmission (4) and lower

onto wood blocks.
7.
Remove sling.
SLING
7
6
4
397-4131
0295 00-2
TM 5-3805-261-23-2
0295 00
REMOVAL - CONTINUED
8.
9.
Support coupling (9).
10.
Remove bolt (11), retainer (10), and coupling (9) from transmission (4) input shaft.
11.
4
8
9
10
12
11
397-4132

Clean and inspection all parts in accordance with WP 0020 00.
INSTALLATION
1.
Position new preformed packing (8) on transmission (4) input shaft.
2.
Position coupling (9).
3.
Install retainer (10) and bolt (11). Tighten bolt to 85 lb-ft (115 Nm).
4.
Install new preformed packing (12) on groove of transmission (4).
5.
Use sling to install housing (5) on transmission (4).
6.
Install 12 new lockwashers (7) and bolts (6).
7.
Remove sling.
8.
Remove two 3/8-16-2B bolts and link brackets.
0295 00-3
TM 5-3805-261-23-2
0295 00
9.
Install new preformed packing (1) and lubricate with

oil.
10.
Install new gasket (2) with seam facing transmission

(4).
11.
Install plug (3).
2
4
12.
Install transmission, adapter, and differential (WP 0294 00).
END OF WORK PACKAGE
0295 00-4
3
397-4129
TM 5-3805-261-23-2
TRANSMISSION CONTROL RELIEF VALVE MAINTENANCE
0296 00

Testing, Removal, Cleaning and Inspection, Installation
INITIAL SETUP
References
Maintenance Level
WP 0020 00
Direct Support

0348 00)
9/16-18 adapter

Materials/Parts
Engine off (TM 5-3805-261-10)

Left side engine panel removed (WP 0182 00)
TESTING
CAUTION
Cap hose ends and plug open ports to prevent contamination.
NOTE
The following test is for transmission pump relief pressure.
Test must be made with transmission hydraulic system at normal operating temperature.
0296 00-1
TM 5-3805-261-23-2
TRANSMISSION CONTROL RELIEF VALVE MAINTENANCE - CONTINUED
0296 00
TESTING - CONTINUED
1.
Disconnect hose assembly (1) from valve assembly (4).
2.
TO DIFFERENTIAL
LOCK VALVE
397-4133
3.
Use a 9/16-18 adapter to install 0 to 200 psi (0 to 1,379 kPa) pressure gauge.
4.
Start engine (TM 5-3805-261-10).
NOTE
Pressure gauge must read 75 psi (517 kPa). If not, replace control relief valve.
5.
Position transmission control lever in neutral. Read

pressure gauge.
6.
Stop engine.
7.
Remove 0 to 200 psi (0 to 1,379 kPa) pressure gauge

and 9/16-18 adapter.
0 TO 200 PSI
PRESSURE GAUGE
9/16 - 18
ADAPTER
397-4134
8.
Install new preformed packing (3) and elbow (2) on valve assembly (4).
9.

0296 00-2
TM 5-3805-261-23-2
0296 00
TESTING - CONTINUED
NOTE
The following test is for transmission oil

cooler relief pressure.
TO TRANSMISSION
SAMPLING VALVE
10.
Disconnect hose assembly (5) from valve assembly

(4).
11.
Remove elbow (8), adapter (7), and preformed packing (6). Discard preformed packing.
4
8
12.
Use a 9/16-18 adapter to install 0 to 200 psi (10 to 1,379 kPa) pressure gauge.
13.
397-4135
NOTE
Pressure gauge must read 75 psi (517 kPa). If not, replace control relief valve.
14.
Position transmission control lever in first speed forward and read pressure gauge.
15.
Stop engine.
16.
Remove 0 to 200 psi (0 to 1,379 kPa) pressure gauge

and 9/16-18 adapter.
0 TO 200 PSI
PRESSURE GAUGE
9/16 - 18
ADAPTER
17.
Install new preformed packing (6), adapter (7), and elbow (8) on valve assembly (4).
18.

0296 00-3
397-4136
TM 5-3805-261-23-2
0296 00
TESTING - CONTINUED
NOTE
The following test is for transmission lubrication oil relief pressure.
19.

valve assembly (4). Discard preformed packing.
20.
Test lubrication oil relief valve. Repeat steps 12

through 16.
21.
10
397-4137
REMOVAL
1.
2.
3.
4.
Remove elbow (8), adapter (7), and preformed packing (6). Discard preformed packing.
5.
6.
7.
8.
11
12
13
5
14
15
0296 00-4
16
397-4138
TM 5-3805-261-23-2
0296 00
REMOVAL - CONTINUED
9.
Support valve assembly (4).
10.
Remove four bolts (17), washers (18), and valve

assembly (4).
17
18
397-4139
11.
19
Remove and discard seven preformed packings (19)

from valve assembly (4).
19
19
19
4
397-4140

INSTALLATION
1.
Install seven new preformed packings (19) in valve assembly (4).
2.
Position valve assembly (4).
3.
Install four washers (18) and bolts (17).
0296 00-5
TM 5-3805-261-23-2
0296 00
4.
5.
6.
7.
8.
Install new preformed packing (6), adapter (7), and

elbow (8).
9.
10.
11.
12.
Turn disconnect switch to ON position and start

engine (TM 5-3805-261-10).
13.
Check for leaks.
14.
Stop engine.
15.
Install left side engine panel (WP 0182 00).
11
12
13
5
14
15
END OF WORK PACKAGE
0296 00-6
16
397-4138
TM 5-3805-261-23-2
TRANSMISSION OIL PUMP REPLACEMENT
0297 00

INITIAL SETUP
Maintenance Level
References
Direct Support
WP 0020 00
Personnel Required
Tool kit, general mechanics, (Item 89, WP 0348

00)
0348 00)
Two
Wood blocks
Materials/Parts
Engine off (TM 5-3805-261-10)
Gasket
Lockwasher (23)
Transmission oil drained (WP 0147 00)
Fan belts removed (WP 0061 00)
0297 00-1
TM 5-3805-261-23-2
TRANSMISSION OIL PUMP REPLACEMENT - CONTINUED
0297 00
REMOVAL
1.
Remove three nuts (5), washers (6), and clips (7) from under plate (1) at rear of transmission. Move wire assembly (4) to
one side.
2.
Remove five bolts (3), washers (2), and plate (1).
2
4
3.
3
397-4141
Remove two bolts (9), lockwashers (8), bolts (10), lockwashers (11), and tube (12). Discard lockwashers.
12
8
10
0297 00-2
11
9
397-4142
TM 5-3805-261-23-2
0297 00
REMOVAL - CONTINUED
4.
Remove preformed packings (13 and 14) from tube
(12) and discard.
13
12
14
397-4143
5.
Remove two bolts (17), lockwashers (16), bolts (18),

lockwashers (19), and tube (15). Discard lockwashers.
19
18
17
6.
Remove and discard preformed packings (20 and 21)

from tube (15).
16
15
397-4144
20
15
21
397-4145
0297 00-3
TM 5-3805-261-23-2
0297 00
REMOVAL - CONTINUED
7.

26
25
24
23
8.

(26) and discard.
22
397-4146
27
26
28
397-4147
0297 00-4
TM 5-3805-261-23-2
0297 00
REMOVAL - CONTINUED
9.

32
33
31
30
10.

(31) and discard.
397-4148
29
35
31
34
397-4149
0297 00-5
TM 5-3805-261-23-2
0297 00
REMOVAL - CONTINUED
WARNING
NOTE
Transmission oil pump weighs 76 lb (35 kg).
11.
Support oil pump (36) with floor jack and wood

block(s).
36
WOOD
BLOCK
FLOOR
JACK
12.
Remove two bolts (40), lockwashers (39), five bolts

(37), lockwashers (38) from oil pump (36). Discard
lockwashers.
37
397-4150
38
36
40
39
397-4151
0297 00-6
TM 5-3805-261-23-2
0297 00
REMOVAL - CONTINUED
13.
Pull oil pump (36) away from dowel on transmission

and rotate pump so it can be lowered out bottom of
machine.
36
397-4152
14.
Remove preformed packing (41) and gasket (42) from

oil pump (36) and discard.
41
42
36
397-4153

0297 00-7
TM 5-3805-261-23-2
0297 00
INSTALLATION
NOTE
Add clean transmission oil to pump before installing.
1.
Use floor jack and wood block(s) to position oil pump

(36), new preformed packing (41), and new gasket
(42) at rear of transmission and align with dowel and
bolt holes.
36,41,42
WOOD
BLOCK
FLOOR
JACK
2.
397-4150
Install oil pump (36), new gasket (42), new preformed packing (41), five new lockwashers (38), and bolts (37), two new
lockwashers (39), and bolts (40).
37
40
38
42
41
39
36
397-4154
0297 00-8
TM 5-3805-261-23-2
0297 00
3.
Install new preformed packings (35 and 34) in tube

(31).
35
31
34
397-4149
4.
Align tube (31) with bolt holes and install two new
lockwashers (32), bolts (33), lockwashers (29), and
bolts (30).
32
33
31
30
0297 00-9
29
397-4148
TM 5-3805-261-23-2
0297 00
5.

(26).
27
26
28
397-4147
6.
Align tube (26) with bolt holes and install two new lockwashers (22), bolts (23), lockwashers (25), and bolts (24).
26
25
24
397-4146
23 22
0297 00-10
TM 5-3805-261-23-2
0297 00
7.

(15).
20
15
21
397-4145
8.
bolts (17).
19
18
17
0297 00-11
16
15
397-4144
TM 5-3805-261-23-2
0297 00
9.

(12).
13
12
14
397-4143
10.
bolts (9).
12
10
11
8
9
0297 00-12
397-2310
TM 5-3805-261-23-2
0297 00
11.
Install plate (1), five washers (2), and bolts (3).
2
4
3
397-4141
12.
Reposition wire assembly (4) under plate (1) and install three clamps (7), washers (6), and nuts (5).
13.
Install fan belts (WP 0061 00).
14.
Fill transmission with oil (WP 0147 00).
15.
Turn battery disconnect switch to ON position and start engine (TM 5-3805-261-10).
16.
Check for leaks.
17.
Stop engine.
END OF WORK PACKAGE
0297 00-13/(-14 Blank)
TM 5-3805-261-23-2
TRANSMISSION OIL COOLER MAINTENANCE
0298 00

INITIAL SETUP
Maintenance Level
References
WP 0020 00
Direct Support


Materials/Parts
Oil, lubricating (Item 26, 27 or 29, WP 0349 00)
Engine off (TM 5-3805-261-10)

Radiator drained (WP 0065 00)
Gasket (5)
Transmission sampling unit removed (WP 0154 00)
REMOVAL
CAUTION
NOTE
Tag hose, lines, and fittings before disconnecting to aid in installation.
0298 00-1
TM 5-3805-261-23-2
TRANSMISSION OIL COOLER MAINTENANCE - CONTINUED
0298 00
REMOVAL - CONTINUED
1.
Disconnect air line (1) from elbow (2).
2.
Remove two bolts (6), oil line (5), and preformed packing (4) from transmission oil cooler core (3). Discard preformed
packing.
3.
Remove two bolts (7), oil line (8), and preformed packing (9) from transmission oil cooler core (3). Discard preformed
packing.
4.
Loosen clamp (11) and slide down on water hose (10).
5.
Remove water hose (10), clamp (11), adapter (12), elbow (13), and adapter (14).
14
13
12
11
8
10
4
5
397-4155
0298 00-2
TM 5-3805-261-23-2
0298 00
REMOVAL - CONTINUED
6.
Remove four bolts (15).
7.
Remove bolts (18 and 19) and withdraw transmission oil cooler and core assembly (17).
8.
Remove and discard gaskets (16 and 20).
15
16
20
17
19
18
397-4156
0298 00-3
TM 5-3805-261-23-2
0298 00
DISASSEMBLY
1.
Remove four bolts (23) from bottom of transmission

oil cooler core (3) and separate access cover (22) and
21
22
23
397-4157
2.
Remove plug (24) and washer (25) from access cover

(22).
25
24
22
397-4158
0298 00-4
TM 5-3805-261-23-2
0298 00
3.
Remove four bolts (28) and gasket (27) from bonnet

(26) and separate from transmission oil cooler core
(3). Discard gasket.
26
28
27
397-4357
4.
Remove two bolts (30), washers (31), cover (32), and

gasket (33) from bonnet (26). Discard gasket.
5.
Remove plug (29).
6.
Remove elbow (2).
31
30
32
33
26
29
2
397-4160
0298 00-5
TM 5-3805-261-23-2
0298 00

ASSEMBLY
1.
Install elbow (2) on bonnet (26).
2.
Install plug (29).
3.
Install new gasket (33), cover (32), two washers (31),

and bolts (30).
31
30
32
26
33
29
2
397-4160
4.
Position bonnet (26) and new gasket (27) on top end

of transmission oil cooler core (3) and install four
bolts (28).
26
28
27
397-4357
0298 00-6
TM 5-3805-261-23-2
0298 00
5.
Install washer (25) and plug (24) in access cover (22).
25
22
24
397-4158
6.
Position new gasket (21) and access cover (22) on bottom end of transmission oil cooler core (3) and install
four bolts (23).
21
22
23
397-4157
0298 00-7
TM 5-3805-261-23-2
0298 00
INSTALLATION
1.
Position two new gaskets (16 and 20) onto transmission oil cooler and core assembly (17) and align with engine mounting bolt holes.
2.
Install bolts (18 and 19) and four bolts (15).
15
16
20
17
19
18
397-4156
0298 00-8
TM 5-3805-261-23-2
0298 00
3.
Install adapter (14), elbow (13), and adapter (12).
4.
Slide clamp (11) onto water hose (10).
5.
Install water hose (10) and clamp (11) onto adapter (12).
NOTE
Lightly lubricate all preformed packings with clean oil before installation.
6.
Install new preformed packing (9), oil line (8), and two bolts (7) on transmission oil cooler core (3).
7.
Install new preformed packing (4), oil line (5), and two bolts (6) on transmission oil cooler core (3).
8.
Connect air line (1) on elbow (2).
14
13
12
11
8
10
4
6
5
397-4155
9.
Install transmission sampling unit (WP 0154 00).
10.
11.
Fill radiator to proper level (WP 0065 00).
12.
13.
Check for leaks.
14.
Stop engine.
END OF WORK PACKAGE

0298 00-9/(-10 Blank)
TM 5-3805-261-23-2
TRANSMISSION OIL FILLER AND OIL LEVEL GAUGE REPLACEMENT
0299 00

INITIAL SETUP
Maintenance Level
Direct Support
0348 00)
Materials/Parts
Bolt, self-locking (2)
Gasket
Lockwasher (5)
Packing, preformed
References
WP 0020 00
Engine off (TM 5-3805-261-10)
Right side engine panel removed (WP 0182 00)
Transmission oil drained (WP 0147 00)
WARNING
Exercise care when working with hot oil or components saturated with hot oil. Allow to cool before
handling. Failure to follow this warning may result in injury to personnel.
Transmission oil is very slippery. Immediately wipe up any spills. Failure to follow this warning may
cause injury to personnel.
0299 00-1
TM 5-3805-261-23-2
TRANSMISSION OIL FILLER AND OIL LEVEL GAUGE REPLACEMENT - CONTINUED
0299 00
REMOVAL
1.
Remove bolt (1) and clamp (2).
2.
Remove bolt (3) and clamp (4).
3
4
397-473
CAUTION
Cap tube ends and open ports to prevent contamination.
NOTE
Position drain pan under tubes.

3.
Remove two bolts (11), lockwashers (10), tube assembly (8), and preformed packing (9). Discard preformed
packing.
4.
Remove screw (7), lockwasher (6), and cap (5) from

tube assembly (8). Discard lockwasher.
8
11
10
9
397-474
0299 00-2
TM 5-3805-261-23-2
TRANSMISSION OIL FILLER AND OIL LEVEL GAUGE REPLACEMENT - CONTINUED
0299 00
REMOVAL - CONTINUED
5.
Remove gauge rod (19) from tube (18).
6.
Remove bolt (15) and washer (14) from clip (13).
7.
Slide clip (13) over.
8.
Remove two self-locking bolts (17), lockwashers (16),

tube (18), and gasket (12). Discard self-locking bolts,
lockwashers and gasket.
19
18
17
16
15
12
14
13
397-476

INSTALLATION
1.
Install new gasket (12), tube (18), two new lockwashers (16), and new self-locking bolts (17).
2.
Position clip (13).
3.
Install washer (14) and bolt (15) in clip (13).
4.
Install gauge rod (19) in tube (18).
5.
Install cap (5), new lockwasher (6) and screw (7) on tube assembly (8).
6.
Install new preformed packing (9), tube assembly (8), two new lockwashers (10), and bolts (11).
7.
8.
9.
Refill transmission oil to proper level (WP 0147 00).
10.
11.
Check for leaks. Stop engine.
12.
Install right side engine panel (WP 0182 00).
END OF WORK PACKAGE

0299 00-3/(-4 Blank)
TM 5-3805-261-23-2
FRONT AXLE ASSEMBLY REPLACEMENT
0300 00

INITIAL SETUP
Personnel Required
Maintenance Level
Direct Support
Two
References

0348 00)
Adapter, puller (Item 9, WP 0348 00)
WP 0020 00
WP 0023 00
Jack stand (Item 85, WP 0348 00)

Nut (Item 45, WP 0348 00)

Puller, hydraulic (Item 60, WP 0348 00)
Pump, hydraulic ram (Item 65, WP 0348 00)

Screw (Item 71, WP 0348 00)
Inplements lowered to ground (TM 5-3805-261-10)

Engine off (TM 5-3805-261-10)
Washer (Item 92, WP 0348 00)

Wood blocks
Front wheels removed (WP 0166 00)
Materials/Parts
Leaning wheel mechanism removed (WP 0303 00)

Bearing (2)
Leaning wheel cylinder removed (WP 0304 00)
Seal (2)
Steering cylinders removed (WP 0320 00)
0300 00-1
TM 5-3805-261-23-2
FRONT AXLE ASSEMBLY REPLACEMENT - CONTINUED
0300 00
REMOVAL
1.
Position jack stand under circle drawbar (1).
JACK STAND
397-2330
2.
Remove seven fittings (2).
0300 00-2
397-4162
TM 5-3805-261-23-2
0300 00
REMOVAL - CONTINUED
WARNING
NOTE
Front axle assembly weighs 1,220 lb (553 kg).
3.
Install sling on front axle assembly (3).
SLING
0300 00-3
397-4163
TM 5-3805-261-23-2
0300 00
REMOVAL - CONTINUED
4.
Remove nut (4), bolt (11), pin (10), and washer (12).
5.
Remove nut (6), bolt (9), pin (5), and washers (7 and
8).
12
11
6.
Use sling to remove front axle assembly (3) and lower

onto wood blocks.
7.
Remove sling.
10
397-4164
SLING
397-4165
3
8.
Remove two seals (13) and bearings (14) from axle

(3). Discard bearings and seals.
14
14
397-4166
13
0300 00-4
TM 5-3805-261-23-2
0300 00

INSTALLATION
1.
Use pulling adapter, hydraulic puller, hydraulic pump, washer, screw, and nut, to install two new bearings (14) 0.282 in.
(7.16 mm) from each surface of front axle assembly (3).
2.
Use driver to install two new seals (13) with lips toward outside surface, even with outside surface of axle (3).
WARNING
NOTE
Front axle assembly weighs 1,220 lb (553 kg).
3.
Attach sling to front axle assembly (3).
4.
Position front axle assembly (3) on machine.
5.
Install washer (8) and pin (5). Install washer (7) only if required to obtain a maximum gap of 0.06 in. (1.5 mm) between
front axle assembly (3) and machine frame. Hole in pin must align with hole in front axle assembly (3).
6.
Install washer (12) and pin (10). Hole in pin must align with hole in front axle assembly (3).
0300 00-5
TM 5-3805-261-23-2
0300 00
7.
Remove sling.
8.
Install bolt (9), nut (6), bolt (11), and nut (4).
9.
Remove jack stand.
11
10.
Install and lubricate seven fittings (2) (WP 0023 00).
2
11.
Install steering cylinder (WP 0320 00).
12.
Install leaning wheel cylinder (WP 0304 00).
13.
Install leaning wheel mechanism (WP 0303 00).
14.
Install front wheels (WP 0166 00).
END OF WORK PACKAGE
0300 00-6
397-4168
397-4162
TM 5-3805-261-23-2
STEERING ARMS AND TIE ROD MAINTENANCE
0301 00

INITIAL SETUP
Maintenance Level
Materials/Parts
Direct Support
Chalk

0348 00)
Gasket
Locknut
Packing, preformed
Pin, cotter (2)
References
Jack, hydraulic (Item 37, WP 0348 00)

Jack stand (2) (Item 84, WP 0348 00)
WP 0020 00
Leg, mechanical puller (Item 40, WP 0348 00)
WP 0166 00
Nut, plain (Item 49, WP 0348 00)
Puller attachment (Item 57, WP 0348 00)

Puller, mechanical (Item 63, WP 0348 00)

Screw, machine (Item 73, WP 0348 00)
Engine off (TM 5-3805-261-10)
Spacer (Item 80, WP 0348 00)
Spacer, sleeve (Item 82, WP 0348 00)

Wheel lean prevention bolt and nut removed (WP

0303 00)
Wheel spindles removed (WP 0302 00)
0301 00-1
TM 5-3805-261-23-2
STEERING ARMS AND TIE ROD MAINTENANCE - CONTINUED
0301 00
REMOVAL
NOTE
This procedure covers replacement of the right steering arm. Follow these instructions for the left steering
arm.
1.
Remove nut (2), washer (3), bolt (5), and lock (6).
2.
Remove bolt (1), washer (9), and retainer (8).
CAUTION
Do not remove pin from wheel lean, lean arm, or lean bar.
3.
Remove pin (4) from leaning wheel rod assembly (7). Drive out pin with hammer and punch just far enough to clear rod
assembly.
4.
5.
Operate wheel lean control lever to retract rod assembly (7) into cylinder (TM 5-3805-261-10).
1
7
397-2332
3
6.
Stop engine.
7.
Turn battery disconnect switch to OFF position (TM 5-3805-261-10).
0301 00-2
TM 5-3805-261-23-2
0301 00
REMOVAL - CONTINUED
8.
Remove and discard cotter pin (12) from front-right socket (10).
9.
Loosen nut (11) until even with end of threads on socket assembly (10).
10.
Tap nut (11) with hammer to loosen socket assembly

(10) from its taper and remove nut (11).
11.
Move socket assembly (10) away from housing (15).
12.
Remove washer (18).
13.
Remove and discard cotter pin (16).
14.
Loosen nut (17) until even with end of threads on

steering cylinder socket assembly (13).
15.
Tap nut (17) with hammer to loosen socket assembly

(13) from its taper and remove nut.
16.
Move socket assembly (13) away from housing (15).
17.
Remove washer (14).
10
16
17
11
12
18
15
14
13
397-4170
18.
19.
Remove ring (22) from retainer (21).
20.
21.
Remove ring (23) from retainer (24).
19
20
21
22
23
26
25
0301 00-3
24
397-4171
TM 5-3805-261-23-2
0301 00
REMOVAL - CONTINUED
22.
Remove two bolts (28) and washers (29).
WARNING
NOTE
Drag link and spindle assembly weighs 415 lb (188 kg).
23.
Attach sling to drag link and spindle assembly (30).
24.
Use assembled puller adapter, washer, nut, screw,

puller assembly, pump group, and spacer to remove
two pins (27).
27
SLING
30
29
28
27
0301 00-4
397-4172
TM 5-3805-261-23-2
0301 00
REMOVAL - CONTINUED
25.
Remove drag link and spindle assembly (30).
26.
Remove sling.
30
397-4173
27.
Remove washers (31, 32, and 33).
28.
Remove seal (34), preformed packing (35), and seal

(40). Discard preformed packing.
29.
Remove plug (38), gasket (39), and plug (37) from

housing (36). Discard gasket.
31
32
33
34
35
36
37
40
0301 00-5
397-4174
39
38
TM 5-3805-261-23-2
0301 00
REMOVAL - CONTINUED
41
30.
Remove locknut (42), bolt (44), and clamp (41). Discard locknut.
31.
Remove socket assembly (45) from steering tie rod

(43).
42
43
45
44
397-4175

INSTALLATION
1.
Install socket assembly (45) on steering tie rod (43).
2.
Install clamp (41), bolt (44), and new locknut (42). Tighten locknut to 55 lb-ft (76 Nm).
3.
Install plug (37), new gasket (39), and plug (38) in

housing (36).
4.
Install seal (40), new preformed packing (35), and seal

(34).
33
5.
Install washers (31, 32, and 33).
34
31
32
35
36
37
40
0301 00-6
397-4174
39
38
TM 5-3805-261-23-2
0301 00
WARNING
NOTE
Drag link and spindle assembly weighs
415 lb (188 kg).
6.
Attach sling to drag link and spindle assembly (30).
30
397-4173
7.
Position drag link and spindle assembly (30) on wheel lean arm.
8.
Lower temperature of two pins (27) to aid in installation.
NOTE
27
SLING
Ensure grooves in two pins are in alignment with openings in housing.

9.
Use assembled puller assembly, pump group, two legs,

puller assembly, bearing puller assembly, and six spacers to install two pins (27).
10.
11.
Remove sling.
30
29
28
27
0301 00-7
397-4172
TM 5-3805-261-23-2
0301 00
19
12.
Install ring (23).
13.
Use driver to install retainer (24), washer (25), and

bolt (26).
14.
Install ring (22).
15.
Install retainer (21), washer (20), and bolt (19).
20
21
22
23
26
25
16.
Install washer (14) on socket assembly (13).
17.
Install socket assembly (13) in housing (15).
18.
Install nut (17) and tighten to 90 lb-ft (122 Nm). Slot

in nut must align with hole in socket assembly (13).
19.
Install new cotter pin (16).
20.
Install washer (18).
21.
Position socket assembly (10) on housing (15).
22.
Install nut (11) and tighten to 90 lb-ft (122 Nm).
23.
24
397-4171
10
16
17
11
12
18
15
14
13
397-4170
24.
0301 00-8
TM 5-3805-261-23-2
0301 00
25.
Operate wheel lean control lever to position rod

assembly (7) in line with pin (4) on right front of
machine.
Stop engine.
27.
Turn battery disconnect switch to OFF position (TM

5-3805-261-10).
28.
Position pin (4) through eye of rod assembly (7) on

front-right of machine.
29.
Install retainer (8), washer (9), and bolt (1).
30.
Install lock (6), bolt (5), washer (3), and nut (2).
Tighten nut to 185 lb-ft (251 Nm).
Install wheel spindles (WP 0302 00).
32.
26.
31.
1
8
397-2332
ADJUSTMENT
1.
Install wheel lean prevention bolt and nut (WP 0303

00).
2.
Raise front axle off ground with jack and support with
two jack stands.
JACK STANDS
0301 00-9
397-4176
TM 5-3805-261-23-2
0301 00
3.
4.
Using a piece of chalk to mark the center of the

threads of both tires, rotate and mark front tires on
front of machine. Tires should be facing straight
ahead.
REAR MEASUREMENT
Measure distance between front centers and rear centers of tires. Front measurement of the tires must be
1/8 to 1/4 in. (3.0 to 6.4 mm) less than the rear measurement of the tires.
397-4177
FRONT MEASUREMENT
MUST BE 1/8 TO 1/4 IN. (3.0 TO 6.4 MM)
LESS THAN REAR MEASUREMENT
5.
Loosen locknut (43) if adjustment is necessary.
6.
Turn steering tie rod (42) in direction needed to obtain

the distance required.
7.
Tighten locknut (43) to 55 lb-ft (75 Nm).
8.
Lower front axle to ground and remove jack and two

jack stands.
9.
Remove wheel lean prevention bolt and nut (WP 0303

00).
42
43
397-4178
END OF WORK PACKAGE
0301 00-10
TM 5-3805-261-23-2
WHEEL SPINDLE, BEARINGS, AND SEALS REPLACEMENT
0302 00

INITIAL SETUP
Maintenance Level
Oil, lubricating (Item 26, 27, 28, 29, or 30, WP
0349 00)
Direct Support

Shop equipment, contact truck (Item 77, WP 0348
00)
0348 00)
Adapter, mechanical puller (Item 2, WP 0348 00)
Inserter, seal (Item 33, WP 0348 00)

Packing, preformed
References
WP 0020 00
Jack group (Item 36, WP 0348 00)
Leg (Item 39, WP 0348 00)

Plate, step (Item 53, WP 0348 00)
Engine off (TM 5-3805-261-10)

Materials/Parts
Cleaning compound (Item 8, WP 0349 00)
Wheel spindle housing lubricant drained (WP 0023

00)
Lubricating oil, gear (Item 23 or 24, WP 0349 00)
0302 00-1
TM 5-3805-261-23-2
WHEEL SPINDLE, BEARINGS, AND SEALS REPLACEMENT - CONTINUED
0302 00
REMOVAL
NOTE
This procedure covers the replacement of the right wheel spindle, bearings, and seals. Follow these instructions for the left wheel spindle, bearings, and seals.
1.
Remove two bolts (3) and cover (4).
2.
NOTE
Tie shim(s) together and tag for identification.
3.
Remove three bolts (2), retainer (6), and shim(s) (7).
4.
Loosen bolt (8) and nut (1).
5.
Position forks of jack group on threads of bolt (8) at center of wheel lean arm. Position other end of jack group against
wheel spindle assembly (9).
1
3
2
4
5
7
397-2333
6.
Remove spindle assembly (9) from housing (10) by

tightening nut on jack group.
7.
Tighten bolt (8) and nut (1).
10
1
8
9
0302 00-2
397-4180
TM 5-3805-261-23-2
0302 00
REMOVAL - CONTINUED
CAUTION
Be careful not to damage ring or spindle.
8.
Remove and separate ring (14) and seal (13) from

spindle. Discard seal.
9.
Use puller to remove bearing (12) from spindle (11).
10.
Remove 10 studs (15) and spindle (9).
11
14
13
12
397-4181
15
11.
Remove and separate ring (19) and seal (20) from

housing (10). Discard seal.
CAUTION
Be careful not to damage seals or rings.
12.
Remove bearings (16, 17, and 18) from housing (10).
16
19
18
10
20
INSTALLATION
1.
Lower temperature of bearings (17 and 18) to aid in installation and install in housing (10).
2.
Install bearing (16) in housing (10).
0302 00-3
397-4182
17
TM 5-3805-261-23-2

0302 00
20
3.
Install new seal (20) on ring (19). Ensure seal is not

twisted and is seated properly on bottom of ring ramp
and against retaining lip.
4.
Install seal inserter on seal (20) and ring (19) as an

assembly.
20
RAMP
19
19
RETAINING LIP
397-4183
WARNING
areas. Keep away from open flames and other sources of ignition. Failure to follow this warning may cause
5.
Use seal inserter to lower seal (20) and ring (19) as an

assembly into container of solvent cleaning compound
until completely wet.
SEAL
INSERTER
20
19
397-4184
6.
Position seal (20) and ring (19) in housing (10). With

ring still wet, use seal inserter to position seal and ring
as an assembly squarely against housing.
7.
Install seal (20) and ring (19). With sudden and even
pressure on the seal inserter, push to seat ring under
retaining lip of housing (10).
SEAL INSERTER
20
10
RETAINING
LIP
19
0302 00-4
397-4185
TM 5-3805-261-23-2
0302 00
8.
Measure at points (A through D), 90 degrees apart

with depth rule gauge. Check height from housing
surface to top of seal (20). Differences in heights
between points (A through D) must not exceed 0.04 in
(1.0 mm).
HOUSING
SURFACE
20
19
HOUSING
SURFACE
397-4186
9.
Adjust seal (20) and ring (19), if necessary, using a seal inserter.
NOTE
If any dirt particles remain on seal face, seal will leak.
10.
Clean seal (20) mating surface with a lint free cloth.
11.
Lubricate mating surface of seal (20) with gear lubricant.
12.
Inspect ring (19) for twists or bulges. Incorrect installation will result in seal (20) failure. If incorrect installation is obvious, repeat steps 6 through 11.
13.
Install 10 studs (15) on spindle (11). Tighten studs to 170 lb-ft (230 Nm).
14.
Install bearing (12) on spindle (11).
15.
Install ring (14) on seal (13). Ensure ring is not twisted and is seated properly on bottom of seal ramp and against retaining lip.
13
20
11
RAMP
14
14
13
12
19
RETAINING LIP
397-4181
15
0302 00-5
397-4183
TM 5-3805-261-23-2
0302 00
16.
Install seal inserter on seal (13) and ring (14).
WARNING
areas. Keep away from open flames and other sources of ignition. Failure to follow this warning may cause
17.
Use seal inserter to lower seal (13) and ring (14) into
container of solvent cleaning compound until ring is
completely wet.
SEAL
INSERTER
13
14
397-4188
18.
Position seal (13) and ring (14) on spindle (9). With

ring still wet, use seal inserter to position seal and ring
squarely against spindle.
19.
Install seal (13) and ring (14). With sudden and even
pressure on the seal inserter, push to seat ring under
retaining lip of spindle (9).
20.
Adjust seal (13) and ring (14), if necessary, using seal

inserter.
SEAL INSERTER
13
9
RETAINING
LIP
14
0302 00-6
397-4185
TM 5-3805-261-23-2
0302 00
21.
Inspect ring (14) for twists or bulges. Ensuring is seated properly on bottom of seal ramp and against retaining lip. Incorrect installation will result in seal failure. If incorrect installation is obvious, repeat steps 18 through 20.
NOTE
If any dirt particles remain on seal face, seal will leak.
22.
Clean seal (13) mating surface with a lint free cloth.
23.
Lubricate mating surface of seal (13) with gear lubricant.
13
13
RAMP
14
14
RETAINING LIP
397-4183
24.
Loosen bolt (8) and nut (1).
25.
Install spindle assembly (11) in housing (10).
26.
Tighten bolt (8) and nut (1).
10
1
8
11
0302 00-7
397-4180
TM 5-3805-261-23-2
0302 00
27.
Install shim(s) (7), retainer (6), and three bolts (2).

Tighten bolts to 96 lb-ft (130 Nm).
28.
Install new preformed packing (5).
29.
Install cover (4) and two bolts (3).
1
3
2
4
5
397-2333
7
30.
Fill wheel spindle housing with lubricant (WP 0023 00).
31.
32.
33.
Operate machine and check for leaks.
34.
Stop engine.
END OF WORK PACKAGE
0302 00-8
TM 5-3805-261-23-2
LEANING WHEEL MECHANISM MAINTENANCE
0303 00

INITIAL SETUP
Maintenance Level
Materials/Parts
Direct Support
Personnel Required

0348 00)
Adapter, bearing remover (Item 1, WP 0348 00)
Two
References
WP 0020 00
WP 0023 00
Nut (Item 45, WP 0348 00)
Nut, plain, round (Item 50, WP 0348 00)

Ratchet assembly (Item 66, WP 0348 00)

Engine off (TM 5-3805-261-10)
Spacer sleeve (Item 82, WP 0348 00)

Steering arms and tie rod removed (WP 0301 00)
0303 00-1
TM 5-3805-261-23-2
LEANING WHEEL MECHANISM MAINTENANCE - CONTINUED
0303 00
REMOVAL
NOTE
This procedure covers replacement of the left arm. Follow these instructions for the right arm.
1.
Install wheel lean lock pin (2) (TM 5-3805-261-10).
2.
Fasten ratchet assembly to arms (4 and 5) on front of machine to reduce the load on pins (1 and 3) to aid in their
removal.
2
3
5
397-2295
3.
Remove nut (11), washer (10), bolt (7), and lock (9)
from left-front of machine.
4.
Remove bolt (13), washer (14), retainer (12), and pin

(8) from bar assembly (6).
9
10
11
12
14
0303 00-2
13
397-4192
TM 5-3805-261-23-2
0303 00
REMOVAL - CONTINUED
WARNING
NOTE
Bar assembly weighs 55 lb (25 kg).
5.
Attach sling to bar assembly (6).
6.
Remove wheel lean lock pin (2) (TM 5-3805-261-10).
7.
Remove bar assembly (6) from arm assemblies (4 and

5).
8.
Remove sling.
SLING
4
397-4193
0303 00-3
TM 5-3805-261-23-2
0303 00
REMOVAL - CONTINUED
9.
Remove four seals (15 and 16) and two bearings (18).
10.
Remove two fittings (17) and bar (19).
17
18
16
15
18
17
16
19
15
397-4194
WARNING
NOTE
20
Arm assembly weighs 60 lb (27 kg).
21
11.
Remove two bolts (26) and washers (24 and 25).
12.
Remove nut (20), bolt (23), washer (22), and lock

(21).
22
23
24
25
26
397-4198
0303 00-4
TM 5-3805-261-23-2
0303 00
REMOVAL - CONTINUED
13.
Attach sling to arm assembly (4).
14.
Remove pin (27).
15.
Remove arm assembly (4).
16.
Remove sling.
SLING
4
27
397-4199
17.
Remove bearings (29 and 30).
18.
Remove fittings (28) from arm assembly (4).
28
29
28
30
397-4200

0303 00-5
TM 5-3805-261-23-2
0303 00
INSTALLATION
CAUTION
19.
To prevent damage, special tools must

be used to install bearings.
These tools must also be used to

install bearing flush with upper surface of collar on arm.
28
Use assembled spacer, nut, pulling adapter, screw, nut,

bearing remover adapter, and hydraulic pump to install
bearing (29) flush with lower surface of collar on arm
(4).
20.
Install bearing (30).
21.
Install two fittings (28) on arm assembly (4).
29
28
30
397-4200
22.
Attach sling to arm assembly (4).
23.
Position arm assembly (4) on machine.
SLING
NOTE
Groove in pin must align with opening in arm assembly.
24.
Install pin (27).
25.
Remove sling.
27
397-4199
0303 00-6
TM 5-3805-261-23-2
0303 00
26.
Install lock (21), washer (22), bolt (23), and nut (20).
27.
Install two washers (24 and 25) and bolts (26).
20
21
22
23
24
25
26
397-4198
28.
Install two fittings (17) in bar (19).
29.
Use assembled washer, puller assembly, hydraulic

pump, screw, nut, and adapter to install two bearings
(18).
30.
Install four seals (15 and 16) with lips toward the outside, even with the outside surface of bar (19).
18
17
16
15
18
17
16
19
15
0303 00-7
397-4194
TM 5-3805-261-23-2
0303 00
31.
Fasten ratchet assembly to arms (4 and 5) and machine

frame.
32.
Attach sling to bar assembly (15).
33.
Position bar assembly (15) on arm assemblies (4 and

5).
34.
Install wheel lean lock pin (2) (TM 5-3805-261-10).
35.
Use ratchet assembly to align arm assemblies (4 and

5) with bar (6).
SLING
15
397-4193
NOTE
Groove in pin must align with opening in top of arm.
36.
Install pin (8).
37.
Install retainer (12), washer (14), and bolt (13). Use

shim(s) between pin (8), and retainer (12) to give a
0.030 in. (0.76 mm) gap between bar (6) and retainer.
38.
9
10
Install lock (9), bolt (7), washer (10), and nut (11).
12
14
0303 00-8
11
13
397-4192
TM 5-3805-261-23-2
0303 00
39.
Remove ratchet assembly from arm assemblies (4 and

5) to put load on pins (1 and 3).
40.
Remove wheel lean lock pin (2) (TM 5-3805-261-10).
41.
Remove sling.
397-2295
42.
Lubricate fittings (WP 0023 00).
43.
Install steering arms and tie rod (WP 0301 00).
ADJUSTMENT
CAUTION
Always check camber after replacement of leaning wheel mechanism to prevent damage to machine. All
motor graders should have 2 degrees of positive camber on each front wheel. Neither wheel should be perpendicular to the ground which will cause excessive wear on tires.
1.
Raise front of machine.
2.
Use a plumb bob over the outside edge of one tire to obtain vertical reference.
0303 00-9
TM 5-3805-261-23-2
0303 00
NOTE
The camber angle and distance is shown on the inner side of the tire to better illustrate how the camber angle
is obtained.
3.
4.
Measure distance from bottom of tire to plumb bob.

Distance should be 0.7 in. (18 mm) which indicates 2
degrees of positive camber.
POSITIVE CAMBER
VERTICAL LINE
CAMBER
ANGLE
Check the other front tire using the same method. If

the camber is more or less than 2 degrees of positive
camber, lengthen or shorten lean bar so camber is correct on both wheels.
AXLE
TIRE
CENTERLINE
ROAD SURFACE
397-2238
END OF WORK PACKAGE
0303 00-10
TM 5-3805-261-23-2
LEANING WHEEL CYLINDER REPAIR
0304 00

INITIAL SETUP
Maintenance Level
Direct Support
Ring (2)
Seal (8)

0348 00)
Expander assembly (Item 23, WP 0348 00)
Seal assembly
Personnel Required
Two
References
Inserter, seal (Item 34,WP 0348 00)
WP 0020 00
Wood blocks
Materials/Parts
Lubricant, thread (Item 22, WP 0349 00)

Oil, lubricating (Item 27 or 28, WP 0349 00)
Engine off (TM 5-3805-261-10)

Leaning wheel cylinder removed (WP 0156 00)
0304 00-1
TM 5-3805-261-23-2
LEANING WHEEL CYLINDER REPAIR - CONTINUED
0304 00
DISASSEMBLY
1.
Remove and discard four seals (1 and 3) from cylinder (4).
CAUTION
Removal of bearings from cylinder eyes may cause destruction of bearings. Remove bearings only if inspection indicates replacement is necessary.
2.
Inspect two bearings (2). Replace if cracked, broken,

scored, or grooved.
3.
Remove two bearings (2), if necessary.
1
2
1
2
397-4205
NOTE
Mount hydraulic cylinder on suitable repair stand to ease disassembly.
4.
Loosen shaft collar (7) until it is completely disengaged from threads of cylinder (5).
5.
Remove connecting link assembly (6) from cylinder

(5).
6
7
397-1886
0304 00-2
TM 5-3805-261-23-2
0304 00
6.
Remove bolt (8), washer (9), and linear actuator piston

assembly (10).
10
397-1887
7.
Remove ring (11) and seal assembly (13) from piston

(12) and discard.
11
12
13
397-1888
8.
Remove linear actuator cap assembly (14) from connecting link rod (15).
14
15
397-1889
9.
Remove ring (16), preformed packing (17), and seals

(19, 20, and 21) from cap (18) and discard.
16
17
18
19
20
21
397-1890
0304 00-3
TM 5-3805-261-23-2
0304 00
10.
Remove shaft collar (7) from connecting link rod (15).
11.
Remove and discard seal (22) from shaft collar (7).
15
22
397-1891

Clean and inspect all parts in accordance with WP
0020 00.
16
ASSEMBLY
1.
Install new seal (22) in shaft collar (7).
2.
Use lubricating oil to lubricate inside of shaft collar

(7).
3.
Install shaft collar (7) on connecting link rod (15).
4.
Use clean oil to lubricate new seals (19, 20, and 21),
new preformed packing (17), and new ring (16).
17
18
19
20
21
397-1890
5.
Use seal inserter to install new seals (19, 20, and 21)
in cap (18). Lip of seal (20) is toward inside of cap.
Lip of seal (19) is toward outside of cap.
6.
Install new preformed packing (17) and new ring (16)

to cap (18).
18
19
20
21
OUTSIDE
397-2499
0304 00-4
TM 5-3805-261-23-2
0304 00
14
7.
Install linear actuator cap assembly (14) on connecting

link rod (15).
15
397-1889
8.
11
Use expander assembly to install new seal assembly

(13) and ring (11) on piston (12).
12
13
397-1888
9.
Install linear actuator piston assembly (10) on connecting link (6).
10.
Use thread lubricant to lubricate threads of bolt (8).

Install washer (9) and bolt. Tighten to 720 to 880 lb-ft
(976 to 1193 Nm).
10
6
397-1887
0304 00-5
TM 5-3805-261-23-2
0304 00
NOTE
Use lubricating oil to lubricate outside of linear actuator cap assembly (14) and inside of cylinder.
11.
Install connecting link (6) inside cylinder (5).
NOTE
Connecting link rod must be fully extended before tightening cap. This will keep cylinder, piston, and head
in alignment.
12.
Tighten cap (14) and shaft collar (7) on cylinder (5) to

350 to 550 lb-ft (475 to 746 Nm).
14
7
397-1886
13.
Install two new bearings (2) centered on cylinder (4),

if removed, allowing installation of four new seals (1
and 3).
14.
Install four new seals (1 and 3) with lips facing outward.
1
2
1
4
2
15.
Install leaning wheel cylinder (WP 0156 00).
END OF WORK PACKAGE

0304 00-6
397-4205
TM 5-3805-261-23-2
DIFFERENTIAL REPLACEMENT
0305 00

INITIAL SETUP
References
Maintenance Level
Direct Support
WP 0020 00

0348 00)

Wood blocks
Engine off (TM 5-3805-261-10)
Materials/Parts

Personnel Required
Transmission, adapter, and differential removed

(WP 0294 00)
Two
REMOVAL
WARNING
0305 00-1
TM 5-3805-261-23-2
DIFFERENTIAL REPLACEMENT - CONTINUED
0305 00
REMOVAL - CONTINUED
NOTE
Differential weighs 500 lb (227 kg).
1.
Attach sling to differential (4).
2.
Remove 10 nuts (2) and washers (3).
3.
Separate differential (4) from transmission (1).
4.
Remove sling.
SLING
4
3
2
397-4206

INSTALLATION
WARNING
NOTE
Differential weighs 500 lb (227 kg).
1.
Attach sling to differential (4).
2.
Position differential (4) to transmission (1).
3.
Install 10 washers (3) and nuts (2).
4.
Remove sling.
5.
Install transmission, adapter, and differential (WP 0294 00).
END OF WORK PACKAGE

0305 00-2
TM 5-3805-261-23-2
DIFFERENTIAL LOCK CONTROL VALVE REPLACEMENT
0306 00

INITIAL SETUP
References
Maintenance Level
WP 0216 00
Direct Support

0348 00)
Materials/Parts

Engine off (TM 5-3805-261-10)

Locknut
Hydraulic pressure relieved (WP 0020 00)
Seal kit
REMOVAL
NOTE
For Type II machines, remove remote group plate for easier access to components.
1.
1
2
397-2311
0306 00-1
TM 5-3805-261-23-2
DIFFERENTIAL LOCK CONTROL VALVE REPLACEMENT - CONTINUED
0306 00
REMOVAL - CONTINUED
CAUTION
NOTE
2.
Disconnect hose assembly (4) from transmission control relief valve (7).
3.
7
397-4133
0306 00-2
TM 5-3805-261-23-2
0306 00
REMOVAL - CONTINUED
4.
Remove hose assembly (8), elbow (18), and preformed packing (17). Discard preformed packing.
5.
Remove cap (12), nut (13), and washer (14).
6.
Disconnect wire assembly (15) from terminal.
7.
Remove two bolts (9), washers (10), and clip (11).
8.
Remove coil assembly (16).
18
10
17
16
11
15
0306 00-3
14 13
12
397-2313
TM 5-3805-261-23-2
0306 00
REMOVAL - CONTINUED
9.
Remove locknut (22) and washers (21). Discard locknut.
10.
Remove coil (20) from solenoid valve assembly (19).
19
22
11.
Remove cartridge (28), seal kit (27), plug (23), preformed packing (24), and two preformed packings
(26) from solenoid valve (25). Discard seal kit and
preformed packing.
21
20
397-4210
23
24
25
27
28
26

INSTALLATION
1.
Install new preformed packings (24 and 26) and plug (23) in valve (25).
2.
Install new seal kit (27) and cartridge (28).
3.
Install coil (20), washer (21), and new locknut (22) on solenoid valve assembly (19).
0306 00-4
397-4211
TM 5-3805-261-23-2
0306 00
4.
Position coil assembly (16).
5.
Install clip (11), two washers (10), and bolts (9).
6.
Connect wire assembly (15) to terminal.
7.
Install washer (14), nut (13), and cap (12).
8.
9.
Install hose assembly (8).
18
9
10
17
16
11
15
10.
Install new preformed packing (6) and elbow (5) to

transmission control relief valve (7).
11.
14
13
397-2313
12
0306 00-5
397-4133
TM 5-3805-261-23-2
0306 00
12.
13.
14.
Turn battery disconnect switch to ON position and

start engine (TM 5-3805-261-10).
15.
Check for leaks.
16.
Refill hydraulic tank if necessary (WP 0216 00).
17.
Stop engine.
2
3
397-2311
END OF WORK PACKAGE
0306 00-6
TM 5-3805-261-23-2
DRIVE AXLES REPLACEMENT
0307 00

INITIAL SETUP
Maintenance Level
Gasket
Direct Support
Lockwasher (8)
Packing, preformed

0348 00)
3/8-16 forcing screw (2)
References
WP 0020 00
1/2-13 forged eyebolt
Materials/Parts

0349 00)
Engine off (TM 5-3805-261-10)

Tandem drive housing drained below drive axle
level (TM 5-3805-261-10)
0307 00-1
TM 5-3805-261-23-2
DRIVE AXLES REPLACEMENT - CONTINUED
0307 00
REMOVAL
NOTE
This procedure covers replacement of right side drive axle. Follow these instructions for left side drive axle.
1.
Remove eight bolts (6), lockwashers (5), cover (4), and gasket (3). Discard gasket and lockwashers.
2.
Bend tabs away from five locks (1) and bolts (2).
3.
Remove five bolts (2) and locks (1).
1
2
5
6
0307 00-2
397-2316
TM 5-3805-261-23-2
0307 00
REMOVAL - CONTINUED
4.
Install two 3/8-16 NC forcing screws to remove

retainer (7).
3/8-16 NC
FORCING SCREWS
397-4213
5.
Remove retainer (7).
6.
Remove two 3/8-16 NC forcing screws.
7.
8.
Install 1/2-13 NC forged eyebolt in end of shaft (9) to

aid in removal.
1/2-13 NC
FORGED EYEBOLT
397-4215
0307 00-3
397-4214
TM 5-3805-261-23-2
0307 00
REMOVAL - CONTINUED
9.
Remove shaft (9) and washer (10) as an assembly.
10.
Remove 1/2-13 NC forged eyebolt.
10
397-4216
1/2-13 NC
FORGED EYEBOLT
NOTE
Removal of washer from shaft may cause
destruction of washer. Remove washer
only if inspection indicates replacement is
necessary.
11.
Inspect washer (10). Replace if cracked, broken, worn,

grooved, or scored.
12.
Remove washer (10), if necessary, from shaft (9).
10
397-4217
0307 00-4
TM 5-3805-261-23-2
0307 00

INSTALLATION
1.
Install new washer (10), if removed.
NOTE
Align splines of shaft with splines in final drive and differential.
2.
Install shaft (9).
3.

retainer (7).
397-4214
NOTE
Lubricate outer diameter of new preformed packing with clean oil.
4.
Position retainer (7) on shaft (9).
5.
Install five locks (1) and bolts (2).
6.
Bend tabs over five bolts (2) and locks (1).
7.
Install new gasket (3) and cover (4).
8.
Install eight lockwashers (5) and bolts (6).
1
2
3
4
5
6
397-2319
9.
Refill differential and tandem drive housing to proper level (TM 5-3805-261-10).
END OF WORK PACKAGE

0307 00-5/(-6 Blank)
TM 5-3805-261-23-2
DRIVE SPROCKETS REPLACEMENT
0308 00

INITIAL SETUP
Maintenance Level
References
WP 0020 00
Direct Support


0348 00)
Socket, spanner (Item 79, WP 0348 00)
Engine off (TM 5-3805-261-10)

Materials/Parts
Tandem drive housing removed (WP 0310 00)
REMOVAL
NOTE
This procedure covers replacement of right side drive sprockets. Follow these instructions for left side drive
sprockets.
0308 00-1
TM 5-3805-261-23-2
DRIVE SPROCKETS REPLACEMENT - CONTINUED
0308 00
REMOVAL - CONTINUED
1.
Remove five bolts (3), locks (2), and retainer (1).
2.
Remove nut (6).
3.
Remove two drive sprockets (4 and 5).
1
2
397-4219

5
6
397-2321
0308 00-2
TM 5-3805-261-23-2
DRIVE SPROCKETS REPLACEMENT - CONTINUED
0308 00
INSTALLATION
1.
Install two drive sprockets (4 and 5) on driveshaft of machine. Install inner sprocket with hub away from final drives.
Install outer sprocket with hub toward hub of inner sprocket.
CAUTION
The following procedure must be used to put the correct amount of preload on the final drive bearings.
2.
Use spanner socket to install nut (6) and tighten to 100 lb-ft (136 Nm).
3.
Turn sprockets (4 and 5) to seat bearings.
4.
Use large punch and hammer to hit hub of sprockets (4 and 5). Repeat steps 2, 3, and 4 until nut (6) does not turn when
tightened.
5.
Loosen nut (6).
6.
Tighten nut (6) to 50 lb-ft (68 Nm).
7.
Position retainer (1) over nut (6).
8.
Check alignment of mount bolt holes. Bolt holes of retainer must line up with bolt holes of sprockets.
9.
Tighten nut (6), if necessary, until mounting bolts can be installed.
10.
Install five locks (2) and bolts (3).
11.
Install tandem drive housing (WP 0310 00).
END OF WORK PACKAGE
0308 00-3/(-4 Blank)
TM 5-3805-261-23-2
FINAL DRIVE ASSEMBLY REPLACEMENT
0309 00

INITIAL SETUP
Materials/Parts
Maintenance Level
Direct Support
Grease, GAA (Item 17, WP 0349 00)

0349 00)

00)
0348 00)

Wire, non-electrical (Item 46, WP 0349 00)
Cup (2)
Ring, retaining
Seal
Leg, puller (Item 41, WP 0348 00)
Washer, thrust (8)
Pin (Item 51, WP 0348 00)

Puller attachment, bearing (Item 55, WP 0348 00)
Personnel Required
Two
Puller attachment, cup (Item 56, WP 0348 00)
References
WP 0020 00

Saddle (Item 70, WP 0348 00)
Socket, spanner (Item 79, WP 0348 00)
Stand assembly (Item 83, WP 0348 00)

Tool, special (Item 90, WP 0348 00)
Wrench, ratchet (Item 93, WP 0348 00)

Engine off (TM 5-3805-261-10)
3/4-10NC forcing screw

Forklift
Drive sprockets removed (WP 0308 00)
0309 00-1
TM 5-3805-261-23-2
FINAL DRIVE ASSEMBLY REPLACEMENT - CONTINUED
0309 00
REMOVAL
NOTE
The following procedure covers replacement of left final drive. Follow these procedures for right final drive.
1.
Remove preformed packing (2) and roller bearing (1). Discard preformed packing.
397-2288
NOTE
Tie shim(s) together and tag for identification.
2.
Remove 16 bolts (7), washers (6), retainer (5), shim(s) (4), and thrust washer (3). Discard thrust washer.
WARNING
NOTE
Tandem housing weighs 2,300 lb (1,043 kg).
7
397-4238
0309 00-2
TM 5-3805-261-23-2
0309 00
REMOVAL - CONTINUED
3.
Support tandem housing (8) and install two link brackets. Position forklift under tandem housing. Secure ratchet assembly to forklift and secure cables to link brackets.
8
RATCHET ASSEMBLY
LINK
BRACKET AND CABLES
4.
397-4222
Use ratchet assembly and cables to remove tandem housing (8) from machine.
RATCHET ASSEMBLY
AND CABLES
8
397-4223
5.
Remove plug (10) and seal (9) from outer housing

(11). Discard seal.
10
11
397-4224
0309 00-3
TM 5-3805-261-23-2
0309 00
REMOVAL - CONTINUED
6.
Remove rings (13 and 14) and thrust washer (12). Discard thrust washer.
7.
Remove 19 nuts (15) and washers (16).
12
16
13
14
15
397-4225
CAUTION
Use rags between saddle and hydraulic jack and planet carrier assembly to prevent damage to housing.
8.
Use saddle and hydraulic jack to support planet carrier

assembly (17).
LINK BRACKET
AND SLING
17
SADDLE AND
FLOOR JACK
397-4226
WARNING
NOTE
Final drive housing weighs 360 lb (163 kg).
Ensure planet carrier assembly is held in place during removal.

0309 00-4
TM 5-3805-261-23-2
0309 00
REMOVAL - CONTINUED
9.
10.
Install two 3/4-10NC forcing screws in housing (19).

Tighten each forcing screw a small amount at a time,
alternating between screws, until housing has been
moved far enough out on the studs to install a link
bracket sling on housing. Put axleshaft (18) in position
in housing to keep planet carrier assembly (17) in balance. Use link bracket sling to carefully remove planet
carrier assembly from machine.
LINK BRACKET
AND SLING
17
18
Install wire from forcing screws behind housing

assembly (19) across planet carrier assembly (17) to
keep inner components from falling.
19
WIRE
3/4-10 NC
FORCING SCREW
397-4227
11.
Position housing (23) on blocks with planet carrier

(22) facing up. Remove wire and forcing screws from
housing.
12.
Remove preformed packing (20) and gear (21). Discard preformed packing.
20
21
WIRE
3/4-10 NC
FORCING SCREW
23
22
397-4228
0309 00-5
TM 5-3805-261-23-2
0309 00
REMOVAL - CONTINUED
WARNING
NOTE
Planet carrier weighs 90 lb (41 kg).
13.
With assistance, use pry bars to carefully remove

planet carrier (22) turning over and placing on flat surface.
14.
Remove six bolts (24), three locks (25), retainers (26),

and shafts (30) from planet carrier (22).
15.
Remove six thrust washers (27 and 29) and three spur
gear assemblies (28). Discard thrust washers.
24
25
30
26
29
28
22
27
397-4229
16.
Remove two roller bearings (31 and 33) from gears

(32).
31
32
33
397-4230
0309 00-6
TM 5-3805-261-23-2
0309 00
REMOVAL - CONTINUED
17.
Remove retaining ring (34) and washer (35) from

planet carrier (22). Discard retaining ring.
34
35
22
397-4231
18.
Remove eight bolts (39), four locks (38), and plates

(37) from housing (23).
19.
Remove gear (40).
20.
Remove spur gearshaft assembly (36).
40
39
36
38
23
37
397-4232
0309 00-7
TM 5-3805-261-23-2
0309 00
REMOVAL - CONTINUED
21.
Remove roller bearing (41) from shaft (42).
41
42
397-4233
22.
Remove and discard cup (43) and seal (44) from housing (23).
23.
Remove and discard cup (45).
43
44
23
45
397-4234

INSTALLATION
1.
Lower temperature of new cup (45) and install in

housing (23).
2.
Lubricate new seal (44) with oil and install with lip of
new seal toward new cup (43).
3.
Turn housing (23) over with new cup (43) and new
seal (44) installed.
4.
Lower temperature of new cup (43) and install.
45
23
397-4236
43,44
5.
Heat roller bearing (41) and install on shaft (42).
0309 00-8
TM 5-3805-261-23-2
0309 00
6.
Install spur gearshaft assembly (36) in housing (23).
7.
Install gear (40).
8.
Install four plates (37), locks (38), and eight bolts (39).
40
36
39
38
23
37
397-4232
9.
Install washer (35) and new retaining ring (34) on

planet carrier (22).
34
35
22
397-4231
0309 00-9
TM 5-3805-261-23-2
0309 00
10.
Install two roller bearings (31 and 33) in gears (32).
31
32
33
397-4230
WARNING
NOTE
Planet carrier weighs 90 lb (41 kg).
11.
With assistance, turn over planet carrier (22) and

install three spur gear assemblies (28), six new thrust
washers (27 and 29), three shafts (30), retainers (26),
locks (25), and six bolts (24) on planet carrier (22).
24
25
30
26
29
28
22
27
397-4229
0309 00-10
TM 5-3805-261-23-2
0309 00
12.
Turn over planet carrier (22) and install over shaft

(36).
22
36
397-4237
13.
Install gear (21) and new preformed packing (20).
14.
Install two 3/4-10NC forcing screws in housing (23).

Attach wire to forcing screws behind housing across
planet carrier (22) to keep planet carrier from falling
when seal (20) and gear (21) are positioned on
machine.
20
21
WIRE
3/4-10 NC
FORCING SCREW
23
22
397-4228
0309 00-11
TM 5-3805-261-23-2
0309 00
WARNING
NOTE
Final drive housing weighs 360 lb (163 kg).
15.
Attach link bracket and sling to planet carrier assembly (17) and position on saddle and floor jack. Put
axleshaft (18) in position in housing (19) to keep
planet carrier assembly in balance.
16.
Move planet carrier assembly (17) to bottom-rear-left

of machine.
17.
Remove wire and two 3/4-10NC forcing screws.
LINK BRACKET
AND SLING
17
18
19
WIRE
3/4-10 NC
FORCING SCREW
397-4227
18.
Position planet carrier assembly (17) on studs of

machine.
LINK BRACKET
AND SLING
17
SADDLE AND
FLOOR JACK
0309 00-12
397-4226
TM 5-3805-261-23-2
0309 00
19.
Remove sling and link bracket and install 19 washers (16) and nuts (15). Tighten nuts to 285 to 315 lb-ft (386 to 427
Nm).
20.
Apply grease to new thrust washer (12) and install.
21.
Lubricate rings (13 and 14) with clean oil and install rings.
22.
Apply oil to new seal (9) and install seal and plug (10) in housing (11).
10
12
16
11
397-4224
0309 00-13
13
14
15
397-4225
TM 5-3805-261-23-2
0309 00
WARNING
NOTE
Tandem housing weighs 2,300 lb (1,043 kg).

23.
Install two link brackets in tandem housing (8).
24.
Use sling to position tandem housing (8) on bottom-rear-left of machine.
25.
Install new thrust washer (3), shim(s) (4), retainer (5), 16 washers (7), and bolts (6).
26.
Apply grease to new thrust washer (3) after installation. Adjust shim(s) (4) to provide 0.0 to 0.0025 in (0.0 to 0.064 mm)
end play between inner housing (23) and outer housing (11). Tighten 16 bolts (6) to 260 to 280 lb-ft (353 to 380 Nm).
27.
Remove link brackets.
LINK BRACKETS
8
3
4
6
23
11
7
28.
Install roller bearing (1) and new preformed packing

(2).
397-4238
397-4220
29.
Install drive sprockets (WP 0308 00).
END OF WORK PACKAGE

0309 00-14
TM 5-3805-261-23-2
TANDEM DRIVE HOUSING ASSEMBLY MAINTENANCE
0310 00

INITIAL SETUP
Maintenance Level
References
Direct Support
WP 0020 00

0348 00)

Engine off (TM 5-3805-261-10)
Materials/Parts
Adhesive (Item 4, WP 0349 00)
Rear wheels removed (WP 0167 00)
Packing, preformed
Right service brakes removed (WP 0313 00)

Air brake lines removed (WP 0161 00)
Personnel Required
Two
Tandem drive housing drained (WP 0023 00)
REMOVAL
WARNING
NOTE
Tandem drive housing weighs 1,310 lb (594 kg).
This procedure covers maintenance of the right side tandem drive housing. Follow these instructions for
the left side tandem drive housing.
0310 00-1
TM 5-3805-261-23-2
TANDEM DRIVE HOUSING ASSEMBLY MAINTENANCE - CONTINUED
0310 00
REMOVAL - CONTINUED
1.
Attach sling and ratchet assembly to tandem drive housing assembly (4).
2.
Remove 18 nuts (1), washers (2), and tandem drive housing assembly (4).
3.
SLING
2
3
4
397-2328
0310 00-2
TM 5-3805-261-23-2
TANDEM DRIVE HOUSING ASSEMBLY MAINTENANCE - CONTINUED
0310 00
DISASSEMBLY
NOTE
Note and mark location of four longer studs to aid in installation.
1.
Remove 24 studs (6) from outside of tandem housing

(7).
2.
Remove 15 studs (5) from inside of tandem housing

(7).
6
7
6
397-4240

ASSEMBLY
1.
Apply adhesive to 15 studs (5) on inside of tandem housing (7) and install.
2.
Apply adhesive to 24 studs (6) on outside of tandem housing (7) and install.
INSTALLATION
1.
2.
Use sling and ratchet assembly to position tandem drive housing assembly (4).
3.
Install 18 washers (2) and nuts (1). Tighten nuts to 175 to 195 lb-ft (237 to 264 Nm).
4.
Install air brake lines (WP 0161 00).
5.
Install right service brakes (WP 0313 00).
6.
Install rear wheels (WP 0167 00).
7.
Fill tandem drive housing (WP 0023 00).
END OF WORK PACKAGE
0310 00-3/(-4 Blank)
TM 5-3805-261-23-2
TANDEM DRIVE CHAIN ASSEMBLY REPLACEMENT
0311 00

INITIAL SETUP
References
Maintenance Level
Direct Support
WP 0020 00


0348 00)
Leg (2) (Item 38, WP 0348 00)

Materials/Parts
Engine off (TM 5-3805-261-10)
Gasket (3)
Pin, cotter (2)
Rear wheels removed (WP 0167 00)
Personnel Required
Two
Drive axles removed (WP 0307 00)
0311 00-1
TM 5-3805-261-23-2
TANDEM DRIVE CHAIN ASSEMBLY REPLACEMENT - CONTINUED
0311 00
REMOVAL
NOTE
This procedure covers replacement of one of the right side tandem drive chain assemblies. Follow these
instructions for left side drive chain assemblies.
1.
Remove four bolts (1), washers (2), cover (3), and gasket (4) from top of tandem housing (5) on right axle, rear frame.
Discard gasket.
2.
Remove two bolts (6), washers (7), cover (8), and gasket (9) from outer side of tandem housing (5). Discard gasket.
3.
Remove two bolts (13), washers (12), cover (11), and gasket (10) from inner side of tandem housing (5). Discard gasket.
11
13
10
12
5
SPINDLE WHEEL
0311 00-2
397-2291
TM 5-3805-261-23-2
0311 00
REMOVAL - CONTINUED
4.
Turn spindle wheel until master link of chain assembly

appears.
5.
Remove and discard two cotter pins (16).
6.
Use puller attachment and two legs to remove bar

(15).
7.
Use puller attachment and two legs to remove link

(14).
PULLER
ASSEMBLY
8.
Turn wheel spindle to left while pulling chain (17) out

of tandem housing (5).
14
15
17
16
WARNING
NOTE
Drive chain weighs 50 lb (23 kg).
9.
Remove chain (17) from tandem drive housing (5).
17
5
397-4243
0311 00-3
397-4242
TM 5-3805-261-23-2
0311 00

1.
Inspect chain for wear and elongation. Measure 12 links at 610 lb (277 kg) of tension. Maximum elongation of chain is
24.72 in (62.9 cm).
2.
Clean and inspect all other parts in accordance with WP 0020 00.
INSTALLATION
NOTE
Master link should be installed with the bar (15) toward the other chain. Ensure the master links of the two
chains are not side by side on the same tooth of the drive sprocket.
1.
Position chain (17) with ends of the chain at the openings of tandem drive housing (5).
2.
Install ratchet assembly on chain (17).
17
5
397-4243
3.
Install puller attachment and two legs on chain (17).
4.
Install link (14) in ends of chain (17).
5.
Remove ratchet assembly from chain (17).
6.
Install bar (15) on link (14).
7.
Remove puller attachment and two legs from chain

(17).
8.
Install two new cotter pins (16) in link (14).
14
PULLER
ASSEMBLY
5
15
17
0311 00-4
16
397-4242
TM 5-3805-261-23-2
0311 00
9.
Install new gasket (10), cover (11), two washers (12), and bolts (13) on inner side of tandem housing (5).
10.
Install new gasket (9), cover (8), two washers (7), and bolts (6) on outer side of tandem housing (5).
11.
Install new gasket (4), cover (3), four washers (2), and bolts (1) on top of tandem housing (5).
11
13
10
12
5
9
12.
Install drive axles (WP 0307 00).
13.
Install rear wheels (WP 0167 00).
END OF WORK PACKAGE
0311 00-5/(-6 Blank)
397-2291
TM 5-3805-261-23-2
PARKING BRAKE ACTUATOR AND RELEASE VALVE REPAIR
0312 00

INITIAL SETUP
References
Maintenance Level
Direct Support
WP 0020 00

0348 00)

Puller attachment (Item 55, WP 0348 00)

Spacer puller screw (Item 81, WP 0348 00)

Materials/Parts
Engine off (TM 5-3805-261-10)

Parking brake actuator and release valve removed

(WP 0157 00)
Packing, preformed seal (2)
0312 00-1
TM 5-3805-261-23-2
PARKING BRAKE ACTUATOR AND RELEASE VALVE REPAIR - CONTINUED
0312 00
DISASSEMBLY
1.
Loosen nut (3).
2.
Remove rod end (2) from air brake chamber assembly

(1).
3.
Remove nut (3).
2
397-4247
4.
Install puller assembly, bearing puller attachment, and spacer on air brake chamber assembly (1).
5.
Remove eight bolts (4).
WARNING
Use caution when removing parts under spring tension. Wear safety glasses. Uncontrolled release of spring
may cause injury to personnel.
6.
Slowly release tension on spring (5) with tooling.
7.
Remove puller assembly, bearing puller attachment,

and spacer.
1
4
0312 00-2
397-4248
TM 5-3805-261-23-2
0312 00
DISASSEMBLY- CONTINUED
8.
Remove cover (11) and spring (10) from housing

assembly (6).
9.
Remove preformed packing (8) and seal (7) from piston (9). Discard preformed packing and seal.
7
8
10
11
397-4249
10.
Remove four screws (16), cover (15), seal (14), and diaphragm (13) from body (12). Discard seal.
12
13
14
15
397-4250
16
397-4250
0312 00-3
TM 5-3805-261-23-2
0312 00

ASSEMBLY
1.
Install diaphragm (13) and new seal (14) on body (12).
2.
Position cover (15) on body (12).
3.
Install four screws (16) on cover (15).
12
13
14
15
397-4250
16
397-4250
0312 00-4
TM 5-3805-261-23-2
0312 00
4.
Install new seal (7) and new preformed packing (8) on

piston (9).
5.
Install housing assembly (6).
6.
Install spring (10) and cover (11) on housing assembly

(6).
7
8
10
11
397-4249
7.
Install puller assembly, bearing puller attachment, and

spacer on air brake chamber assembly (1).
8.
Push spring (5) into air brake chamber assembly (1)

with tooling.
9.
Install eight bolts (4).
10.
Remove puller assembly, bearing puller attachment,

and spacer.
1
4
0312 00-5
397-4248
TM 5-3805-261-23-2
0312 00
11.
Loosely install nut (3).
12.
Install rod end (2) to air brake chamber assembly (1).
13.
Tighten nut (3).
14.
Install parking brake actuator and release valve (WP

0157 00).
2
397-4247
END OF WORK PACKAGE
0312 00-6
TM 5-3805-261-23-2
SERVICE BRAKES MAINTENANCE
0313 00

Disassembly, Cleaning and Inspection, Assembly, Adjustment
INITIAL SETUP

0348 00)
Lockwasher (4)
Seal (4)
Seal assembly (2)
Personnel Required
Two
Installer, seal (Item 33, WP 0348 00)

References
WP 0020 00

Wood blocks
Engine off (TM 5-3805-261-10)
Materials/Parts

Oil, lubricating (Item 29, WP 0349 00)
Service brake and wheel spindle housing assembly

0313 00-1
TM 5-3805-261-23-2
SERVICE BRAKES MAINTENANCE - CONTINUED
0313 00
DISASSEMBLY
1.
Remove three bolts (1), retainer (2), shim(s) (3), and

sprocket (4).
2.
Remove cone roller (5) and seal (6). Discard seal.
3.
Remove bolt (12), lockwasher (11), plate (10), three

bolts (9), and lockwashers (8) from cover (7). Discard
lockwashers.
1
2
3
4
5
6
7
8
9
10
11
12
397-1920
0313 00-2
TM 5-3805-261-23-2
0313 00
4.
Install two link brackets in cover (7).
WARNING
NOTE
Cover weighs 50 lb (23 kg).
5.
Install sling to link brackets.
6.
Remove cover (7) from housing (13) and place on

wood blocks.
7.
Remove sling.
8.
Remove two link brackets.
SLING
LINK
BRACKET
13
397-1921
0313 00-3
TM 5-3805-261-23-2
0313 00
9.
Remove seal (14) and cup (15) from cover (7). Discard seal.
14
15
7
397-1922
10.
Remove hub (16) from housing (13).
NOTE
Note order of discs to aid in assembly.
11.
Remove 10 discs (17) and nine disc assemblies (18) from housing (13).
16
WARNING
17
Use caution when spring is compressed.

Wear safety glasses when removing
springs. Accidental release of spring may
cause injury to personnel.
12.
18
Remove six bolts (19), washers (20), and springs (21).
17
19
20
21
13
397-1923
0313 00-4
TM 5-3805-261-23-2
0313 00
13.
Install two link brackets in housing assembly (22).
WARNING
NOTE
Housing weighs 100 lb (46 kg).
14.
Install sling to link brackets.
15.
Remove housing assembly (22) from spindle assembly (23).
16.
Remove sling.
17.
SLING
LINK
BRACKET
22
23
397-1924
0313 00-5
TM 5-3805-261-23-2
0313 00
18.
Use wood blocks, cup puller attachments, torque, and bearing puller attachment to remove piston assembly (24) from
housing (13).
PULLER ASSEMBLY
13
RATCHET BOX
WRENCH
24
BEARING CUP
PULLING ATTACHMENT
19.
WOOD BLOCKS
Remove seals (25 and 26) from piston (27). Discard

seals.
397-1925
25
26
27
397-1926
0313 00-6
TM 5-3805-261-23-2
0313 00
20.
Remove seal assembly (28), cup (29), and plug (30)

from housing (13). Discard seal assembly.
28
29
30
13
397-1927
21.
Use a bearing separator and puller to remove cone

(31) from spindle (33).
22.
Remove seal assembly (32) and 10 studs (34) from

spindle (33). Discard seal assembly.
31
32
33
34
0313 00-7
397-1928
TM 5-3805-261-23-2
0313 00

1.
Inspect three bolts (1) and bolt holes for wear and
damage.
2.
If hole threads are damaged or bolts (1) cannot be

hand-tightened in hole, replace bolts and spindle (33).
33
397-1920
3.
Clean and inspect all other parts in accordance with WP 0020 00.
0313 00-8
TM 5-3805-261-23-2

ASSEMBLY
0313 00
31
1.
Install 10 studs (34) on spindle (33).
2.
Use seal installer to install new seal assembly (32) on

spindle (33).
3.
Coat metal surface of seal assembly (32) with clean

oil.
4.
Heat cone (31).
5.
Install cone (31) on spindle (33).
32
33
34
397-1928
6.
Install plug (30) on housing (13).
7.
Lower temperature of cup (29).
8.
Install cup (29) on housing (13).
9.
Use seal installer to install new seal assembly (28) on

housing (13).
10.
Coat metal surface of seal assembly (28) with clean

oil.
28
29
30
13
397-1927
0313 00-9
TM 5-3805-261-23-2
0313 00
11.
Install new seals (25 and 26) on piston (27).
25
26
27
397-1926
12.
Install piston assembly (24) on housing (13).
PULLER ASSEMBLY
13
RATCHET BOX
WRENCH
24
BEARING CUP
PULLING ATTACHMENT
WOOD BLOCKS
0313 00-10
397-1925
TM 5-3805-261-23-2
0313 00
13.
Install two link brackets on housing assembly (22).
14.
Install sling.
15.
Install housing assembly (22) on spindle assembly

(23).
16.
Remove sling.
17.
SLING
LINK
BRACKET
22
23
397-1924
0313 00-11
TM 5-3805-261-23-2
0313 00
18.
Install six springs (21), washers (20), and bolts (19) on housing (13).
19.
Apply a thin coat of clean oil to nine disc assemblies (18) and 10 discs (17).
NOTE
Ensure there is a disc assembly between each disc.
20.
Starting with a disc, install 10 disc (17) and nine disc assemblies (18) on housing (13).
21.
Install hub (16) on spindle (33).
16
17
18
17
19
20
21
33
13
397-1923
22.
Install new seal (14) on cover (7).
23.
Coat seal (14) with grease.
24.
Lower temperature of cup (15).
25.
Install cup (15) on cover (7).
14
15
7
397-1922
0313 00-12
TM 5-3805-261-23-2
0313 00
26.
Install two link brackets on cover (7).
WARNING
27.
Install sling.
28.
Install cover (7) on housing (13).
29.
Remove sling.
30.
SLING
LINK
BRACKET
13
397-1921
0313 00-13
TM 5-3805-261-23-2
0313 00
31.
Install seal (6) on cover (7).
32.
Coat seal (6) with grease.
33.
Install three new lockwashers (8), bolts (9), plate (10),

new lockwasher (11), and bolt (12).
34.
Install cone roller (5) over spindle (33).
1
2
3
4
5
6
33
7
8
13
9
10
11
12
397-1920
NOTE
The sprocket for the front service brake and wheel spindle housing must be installed with teeth next to cover.
The sprocket for the rear service brake and wheel spindle housing must be installed with teeth away from
cover.
35.
Install sprocket (4) over splines on spindle (33).
36.
Install retainer (2) and three bolts (1). Tighten bolts to

35 lb-ft (47 Nm) while turning housing (13).
37.
Remove three bolts (1) and retainer (2).
38.
Use a caliper to measure distance between end of

sprocket (4) and spindle (33).
39.
Install shim(s) (3), which have total thickness equal to

distance measured in step 38 minus 0.010 to 0.015 in.
(0.25 to 0.38 mm).
40.
Install retainer (2) and three bolts (1). Tighten bolts to

192 lb-ft (260 Nm).
41.
Install service brake and wheel spindle housing assembly (WP 0314 00).
0313 00-14
SHIM(S)
33
397-2500
TM 5-3805-261-23-2
0313 00
ADJUSTMENT
1.
Fully release pedal (35) from beneath floor plate on right side of cab.
2.
Check roller (39). Roller must be slightly in contact with plunger of brake control valve (40). A slight drag will be felt if
roller is turned.
3.
Clean stop (38) as required to make contact. Ensure there is no dirt between stop and floor.
4.
Vent all air pressure (TM 5-3805-261-10).
5.
Loosen nut (42).
6.
Back out screw (41). A slight drag must be felt when roller (39) is turned.
7.
Loosen nut (37).
8.
Turn stop screw (36) all the way down.
9.
Depress pedal (35) and hold until solid stop in valve is felt. This is maximum stroke of valve.
NOTE
If pedal hits platform before maximum stroke of valve is felt, back out screw (41) one turn.
10.
Turn stop screw (36) up until contact is made with pedal (35) in depressed position.
11.
Release pedal (35).
12.
Tighten nuts (42 and 37). Do not turn stop screw (36) and screw (41) after nuts are tightened.
13.
Depress pedal (35) and release. Check to ensure valve is exhausting when pedal is up; there must be no pressure (0 psi)
at tandem.
36
35
37
38
39
42
397-478
41
40
END OF WORK PACKAGE

0313 00-15/(-16 Blank)
TM 5-3805-261-23-2
SERVICE BRAKE AND WHEEL SPINDLE HOUSING ASSEMBLY REPLACEMENT
0314 00

INITIAL SETUP
Maintenance Level
Personnel Required
Two
Direct Support
References

0348 00)
WP 0020 00

7/8-14 nut (2)
Wood blocks
Engine off (TM 5-3805-261-10)
Materials/Parts

Tandem drive chain assembly removed (WP 0311

00)
Lockwasher (12)
0314 00-1
TM 5-3805-261-23-2
SERVICE BRAKE AND WHEEL SPINDLE HOUSING ASSEMBLY REPLACEMENT - CONTINUED
0314 00
REMOVAL
NOTE
The following is a maintenance procedure for the right-rear brake and wheel spindle housing assembly. The
maintenance procedure for the remaining three brake and wheel spindle housing assemblies is identical.
1.
Remove two nuts (5), lockwashers (6), and guard (4) from brake and wheel spindle housing assembly (8). Discard lockwashers.
CAUTION
NOTE
Tag hose and tube assemblies before removal to aid in installation.
2.
Loosen two nuts (2) on tube assembly (1).
3.
Remove tube assembly (1), elbow (3), bolt (7), and plate (9) from brake and wheel spindle housing assembly (8).
0314 00-2
7
8
397-4254
TM 5-3805-261-23-2
0314 00
REMOVAL - CONTINUED
WARNING
NOTE
Brake and wheel spindle housing assembly weighs 350 lb (159 kg).
4.
Install sling assembly on brake and wheel spindle housing assembly (8).
5.
Install two 7/8-14 nuts on studs (11).
6.
Remove ten nuts (12) and lockwashers (13). Discard lockwashers.
7.
Use ratchet assembly to remove brake and wheel spindle housing assembly (8) from tandem drive housing assembly
(10).
8.
Place brake and wheel spindle housing assembly (8) on wood blocks.
9.
Remove two 7/8-14 nuts from studs (11).
10.
Remove sling assembly.
SLING
10
7/8-14
NUTS
11
13 12
8
397-4255

0314 00-3
TM 5-3805-261-23-2
0314 00
INSTALLATION
WARNING
NOTE
Brake and wheel spindle housing assembly weighs 350 lb (159 kg).
1.
Install sling on brake and wheel spindle housing assembly (8).
2.
Install two 7/8-14 nuts on studs (11).
3.
Install brake and wheel spindle housing assembly (8) to tandem drive housing assembly (10).
4.
Install 10 new lockwashers (13) and nuts (12).
5.
Remove two 7/8-14 nuts from studs (11).
6.
Remove sling.
SLING
10
7/8-14
NUTS
11
13 12
8
397-4255
0314 00-4
TM 5-3805-261-23-2
0314 00
7.
Install plate (9), bolt (7), elbow (3), and tube assembly
(1) on brake and wheel spindle housing assembly (8).
8.
Tighten two nuts (2) on tube assembly (1).
9.
Install guard (4), two new lockwashers (6), and nuts

(5).
9
7
8
4
5
397-2297
10.
Install tandem drive chain assembly (WP 0311 00).
END OF WORK PACKAGE
0314 00-5/(-6 Blank)
TM 5-3805-261-23-2
REMOTE STEER AIR VALVES REPLACEMENT (TYPE II MACHINE)
0315 00

Removal, Installation
INITIAL SETUP
Maintenance Level
Direct Support
Engine off (TM 5-3805-261-10)
Materials/Parts

0182 00)
0315 00-1
TM 5-3805-261-23-2
REMOTE STEER AIR VALVES REPLACEMENT (TYPE II MACHINE) - CONTINUED
0315 00
REMOVAL
CAUTION
NOTE
Each of two steer air valves is removed the same way. Left steer air valve is shown.
Tag air lines before disconnecting to aid in installation.
1.
Disconnect air lines (3, 6, and 9) from three elbows (2)

of steer air valve (1).
2.
Remove three elbows (2) from steer air valve (1).
3.
Disconnect air line (5) from elbow (4) at top of tee (8).
4.
Remove elbow (4) from tee (8).
5.
Disconnect air line (7) from bottom of tee (8).
6.
Remove tee (8) from steer air valve (1).
2
6
9
397-4378
NOTE
Note position of plug at top of steer air valve for installation.
7.
Remove two bolts (10) and steer air valve (1) from
valve bracket (11).
8.
Remove two nuts (15), four washers (16), two bolts

(17), and valve bracket (11) from bracket (12).
10
11
12
NOTE
Perform steps 9 and 10 to remove bracket
from top of transmission.
9.
10.
Remove two bolts (18), washers (19), and bracket (12)

from transmission.
18,19
0315 00-2
15,16,17
13,14
397-4380
TM 5-3805-261-23-2
REMOTE STEER AIR VALVES REPLACEMENT (TYPE II MACHINE) - CONTINUED

INSTALLATION
NOTE
Each of two steer air cylinders is installed the same way. Left steer air cylinder is shown.
Perform steps 1 and 2 to install bracket to top of transmission.
1.
Install bracket (12) to transmission with two washers (14) and bolts (13).
2.
3.
Install valve bracket (11) to bracket (12) with two bolts (17), four washers (16), and two nuts (15).
NOTE
Ensure plug at top of steer air valve is in position noted. Change position if necessary.
4.
Install steer air valve (1) to valve bracket (11) with two bolts (10).
5.
Install tee (8) to steer air valve (1).
6.
Connect air line (7) to bottom of tee (8).
7.
Install elbow (4) to top of tee (8).
8.
Connect air line (5) to elbow (4).
9.
Install three elbows (2) to steer air valve (1).
10.
Connect air lines (3, 6, and 9) to three elbows (2).Install left and right side engine panels (WP 0182 00).
END OF WORK PACKAGE
0315 00-3/(-4 Blank)
0315 00
TM 5-3805-261-23-2
AIR BRAKE VALVE REPLACEMENT
0316 00

INITIAL SETUP
Maintenance Level
Direct Support

Materials/Parts

Engine off (TM 5-3805-261-10)

Rubber spring
Blackout and service lights switches removed (WP

0117 00)
Washer
Air pressure switch removed (WP 0129 00)

Air brake controls removed (WP 0160 00)
References
Air brake lines removed (WP 0161 00)

Air brake control lines disconnected (WP 0161 00)
WP 0020 00
0316 00-1
TM 5-3805-261-23-2
AIR BRAKE VALVE REPLACEMENT - CONTINUED
0316 00
REMOVAL
Remove three bolts (3), washers (4), bracket (2), shaft (5), and air brake valve (1) from under right side of cab.
3
5
4
397-4273

INSTALLATION
1.
Install air brake valve (1), shaft (5), bracket (2), three
washers (4), and bolts (3) under right side of cab.
2.
Connect air brake control line (WP 0161 00).
3.
Install air brake lines (WP 0161 00).
4.
Install air brake controls (WP 0160 00).
5.
Install air pressure switches (WP 0129 00).
6.
Install blackout and service lights switches (WP 0117

00).
3
5
4
397-2322
END OF WORK PACKAGE

0316 00-2
TM 5-3805-261-23-2
AIR COMPRESSOR ASSEMBLY REPLACEMENT
0317 00

INITIAL SETUP
Maintenance Level
Washer (2)
Direct Support
References

Tool kit, general mechanics (Item 89, (WP 0348
00)
0348 00)
WP 0020 00
Materials/Parts
Petrolatum, technical (Item 33, WP 0349 00)
Engine off (TM 5-3805-261-10)

Gasket (7)
Cooling system drained below cylinder head level

(WP 0065 00)
Grommet (2)
Lockwasher (24)
Air compressor lines and fittings removed (WP

0318 00)
0317 00-1
TM 5-3805-261-23-2
AIR COMPRESSOR ASSEMBLY REPLACEMENT - CONTINUED
0317 00
REMOVAL
1.
2.
3.
Remove bolt (4) and two washers (5).

Position tube assembly (3) away from air compressor
(8).
Remove bolt (6), washer (7), bolt (2), and washer (1).
397-484
WARNING
NOTE
Weight of air compressor is 34 lb (16 kg).
4.
Remove air compressor (8) and gasket (9) from front

timing gear housing in left-front side of engine. Discard gasket.
397-4285

0317 00-2
TM 5-3805-261-23-2
AIR COMPRESSOR ASSEMBLY REPLACEMENT - CONTINUED
0317 00
INSTALLATION
NOTE
Align and engage splines of air compressor shaft with water pump drive gear.
1.
Position new gasket (9) and air compressor (8) on

backside of front timing gear housing in left-front side
of engine.
397-4285
2.
Install washer (1), bolt (2), washer (7), and bolt (6) on
air compressor (8).
3.
Position tube assembly (3) on air compressor (8).
4.
Install two washers (5) and bolt (4), securing tube

assembly (3).
8
5.
Install air compressor lines and fittings (WP 0318 00)
6.
Refill cooling system to proper level (WP 0065 00).
7.
8.
Run engine for two minutes. Stop engine.
9.
Check for leaks.
10.
END OF WORK PACKAGE
0317 00-3/(-4 Blank)
397-484
TM 5-3805-261-23-2
AIR COMPRESSOR LINES AND FITTINGS REPLACEMENT
0318 00

INITIAL SETUP
Maintenance Level
Direct Support
Engine off (TM 5-3805-261-10)
Materials/Parts
References
Air pressure relieved (WP 0161 00)
WP 0020 00
Cooling system drained below cylinder head level

(WP 0065 00)
WP 0113 00
0318 00-1
TM 5-3805-261-23-2
AIR COMPRESSOR LINES AND FITTINGS REPLACEMENT - CONTINUED
0318 00
REMOVAL
CAUTION
NOTE
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Disconnect tube assembly (4) from elbow (1) on cylinder head (5).
Remove tube assembly (4) from connector (3).
Remove elbow (1) from air compressor (12).
Remove connector (3) and bushing (2) from cylinder head (5).
Disconnect and remove tube assembly (7) from elbows (6 and 8).
Remove elbow (8) from transmission oil cooler.
Disconnect and remove tube assembly (10) from elbows (9 and 11).
Remove elbow (9) from engine.
Remove two oil pressure sending units from cross lubricant line (WP 0113 00).
5
9
10
12
CROSS LUBRICANT LINE
0318 00-2
11
397-2342
TM 5-3805-261-23-2
0318 00
REMOVAL - CONTINUED
12.
Disconnect and remove tube assembly (15) from

elbows (13 and 16).
13.
14.
Remove elbow (13) from governor (14).
14
13
15
16
12
15.
Disconnect and remove hose assembly (21) from connectors (20 and 22).
16.
Remove connector (20) from cross (19).
17.
Remove connector (22) from air compressor (12).
18.
Remove cross (19) from nipple (18).
19.
Remove nipple (18) and adapter (17) from engine

block.
397-487
17
18 19
20
12
22
21
397-488

0318 00-3
TM 5-3805-261-23-2
0318 00
INSTALLATION
1.
Install adapter (17) and nipple (18) on engine block.
2.
Install cross (19) on nipple (18).
3.
Install connector (22) on air compressor (12).
4.
Install connector (20) on cross (19).
5.
Connect hose assembly (21) on connectors (20 and

22).
17
18 19
20
12
22
21
397-488
6.
Install elbow (13) on governor (14).
7.
Install elbow (16) on air compressor (12).
8.
Connect tube assembly (15) on elbows (13 and 16).
14
13
15
16
12
0318 00-4
397-487
TM 5-3805-261-23-2
0318 00
9.
Install two oil pressure sending units on cross lubricant line (WP 0113 00).
10.
Install elbow (9) on air intake manifold in air compressor (12).
11.
12.
13.
Install elbow (8) on transmission oil cooler.
14.
15.
16.
Install bushing (2) and connector (3) on cylinder head (5) in air compressor (12).
17.
18.
Connect tube assembly (4) on connector (3) and elbow (1).
19.
Fill cooling system to operating level (WP 0065 00).
4
6
5
9
10
12
11
END OF WORK PACKAGE
0318 00-5/(-6 Blank)
397-486
TM 5-3805-261-23-2
STEERING CONTROL PUMP MAINTENANCE
0319 00

INITIAL SETUP
Maintenance Level
References
WP 0020 00
Direct Support

0348 00)

Materials/Parts
Engine off (TM 5-3805-261-10)
O-ring (4)
Horn switch removed (WP 0120 00)
Steering console panel and hood removed (WP

0196 00)
Seal (2)
0319 00-1
TM 5-3805-261-23-2
STEERING CONTROL PUMP MAINTENANCE - CONTINUED
0319 00
REMOVAL
CAUTION
Cap hose end and plug open ports to prevent contamination.
NOTE
1.
Disconnect hose assemblies (1, 4, 6, and 8) and remove O-rings (2, 5, 7, and 9). Discard O-rings.
2.
Remove control pump assembly (3).
3
1,2
8,9
6,7
4,5
397-491
0319 00-2
TM 5-3805-261-23-2
0319 00
REMOVAL - CONTINUED
3.
Remove two connectors (10) and preformed packings

(13) from control pump assembly (3). Discard preformed packings.
4.
Remove two connectors (11) and preformed packings

(12) from control pump assembly (3). Discard preformed packings.
11
10
12
13
3
397-492
DISASSEMBLY
1.
Remove four bolts (16), shaft (14), and housing (15)

as an assembly from control pump (3).
14
15
16
397-4316
0319 00-3
TM 5-3805-261-23-2
0319 00
2.
Remove retaining rings (17 and 18), bearing (16), and

shaft (14) from housing (15).
14
16
15
17
18
397-4317
3.
4.
Remove seven bolts (19), cap (20), and preformed

packing (21) from liquid pump assembly (25). Discard
preformed packing.
19
20
21
Remove gear rotor (22), spacer (23), inner gear (24),

preformed packing (29), driver (28), spacer (27), and
preformed packing (26). Discard preformed packing.
22
23
29
24
28
27
25
26
397-4318
5.
Remove sleeve (30), spool (31), race (32), bearing

(33), and race (34) as an assembly, from liquid pump
housing (35).
30
31
32 33
34
35
397-4319
0319 00-4
TM 5-3805-261-23-2
0319 00
6.
Remove pin (36), sleeve (30), spool (31), and six

springs (37).
36
30
37
31
397-4320
7.
35
Remove snap ring (42), sleeve bushing (40), seals (39

and 41), and preformed packing (38) as an assembly,
from liquid pump housing (35). Discard preformed
packing.
38
NOTE
39,40,41
42
Use small threaded screw for removal of the seat.

8.
Remove screw (44), seat (45), preformed packings (43

and 46), ball (47), and retainer (48) from liquid pump
housing (35). Discard preformed packing.
48
43
44
47
46
45
397-4321
9.
Remove seal (41) and preformed packing (39) from

bushing (40). Discard seals.
39
40
41
397-4322
0319 00-5
TM 5-3805-261-23-2
0319 00

ASSEMBLY
1.
Install new seal and preformed packing (39) and seal (41) on bushing (40).
35
39
38
40
39,40,41
42
41
48
397-4322
43
44
47
46
45
397-4321
NOTE
Lubrication may be necessary for assembly.
2.
Install retainer (48), ball (47), new preformed packing (46), seat (45), new preformed packing (43), and screw (44) in
pump body (35). Tighten screw to 96 lb-in. (11 Nm).
3.
Install new preformed packing (38), sleeve bushing (40), preformed packing (39), seal (41), and snap ring (42) as an
assembly in liquid pump housing (35).
4.
Install spool (31), sleeve (30), and pin (36).
5.
Install six springs (37) in spool (31) and sleeve (30).

Ensure curves of springs are in contact and in center of
spool.
36
30
37
31
397-4320
0319 00-6
TM 5-3805-261-23-2
0319 00
6.
30
Install race (34), bearing (33), race (32), spool (31),

and sleeve (30) as an assembly, into liquid pump housing (35).
31
32 33
34
35
397-4319
NOTE
Pin (36) in sleeve assembly must be in alignment with gear.
36
24
397-4324
7.
8.
Install new preformed packing (26), spacer (27),

driver (28), new preformed packing (29), inner gear
(24), spacer (23), and gear rotor (22) into liquid pump
assembly (25).
19
20
Install new preformed packing (21), cap (20), and

seven bolts (19).
21
22
23
29
24
28
27
26
25
397-4318
0319 00-7
TM 5-3805-261-23-2
0319 00
9.
Tighten seven bolts to 120 lb-in. (14 Nm) in the order

shown. Then tighten to 252 lb-in. (28 Nm).
1
3
397-4323
10.
Install shaft (14), bearing (16), and retaining rings (17

and 18) into housing (15).
14
16
15
17
18
397-4317
11.
Install shaft (14) and housing (15) as an assembly, and

four bolts (16) on control pump (3).
3
14
15
16
397-4316
0319 00-8
TM 5-3805-261-23-2
0319 00
INSTALLATION
1.
Install two new preformed packings (13) and connectors (10) on control pump (3).
2.
Install two connectors (11) and new preformed packing (12) on control pump (3).
11
10
12
13
3
397-492
3.
Install control pump (3) on steering console.
4.
Connect hose assemblies (1, 4, 6, and 8) and new Orings (2, 5, 7, and 9).
3
1,2
8,9
6,7
4,5
397-491
5.
Install horn switch (WP 0120 00).
6.
Install steering console panel and hood (WP 0196 00).
END OF WORK PACKAGE
0319 00-9/(-10 Blank)
TM 5-3805-261-23-2
STEERING CYLINDER REPAIR
0320 00

INITIAL SETUP
Maintenance Level
Packing, preformed
Direct Support
Seal assembly

0348 00)
Seal (3)
References
WP 0020 00

Wood blocks
Materials/Parts

Engine off (TM 5-3805-261-10)
Steering cylinder removed (WP 0176 00)
0320 00-1
TM 5-3805-261-23-2
STEERING CYLINDER REPAIR - CONTINUED
0320 00
DISASSEMBLY
1.
Remove two rings (4) and bearing (1).
2.
Loosen linear actuator cap assembly (3).
3.
Remove cylinder tube (2).
1
4
397-1930
4.
5.
Remove linear actuator assembly (7).
397-1931
0320 00-2
TM 5-3805-261-23-2
0320 00
6.

(9). Discard seal assembly.
9
10
397-1932
7.
Remove hydraulic motor head assembly (11).
11
397-1933
8.
Remove seals (15 and 16), preformed packing (12),

and ring (13) from head (14). Discard seals and preformed packing.
12
13
14
15
16
397-1934
0320 00-3
TM 5-3805-261-23-2
0320 00
9.
Remove linear actuator cap assembly (3) from cylinder shaft (17).
17
397-1935
10.
Remove seal (19) from cap (18). Discard seal.
18
19
397-1936

0320 00-4
TM 5-3805-261-23-2
0320 00
ASSEMBLY
1.
Install new seal (19) into cap (18).
2.
Install linear actuator cap assembly (3) on cylinder shaft (17).
3.
Coat ring (13), new preformed packing (12), and new

seals (15 and 16) with lubricating oil.
4.
Install ring (13), new preformed packing (12), and

new seals (15 and 16) in head (14).
5.
Ensure lip of seal (16) is facing toward inside of head

(14) and lip of seal (15) is facing toward outside of
head.
12
13
14
15
16
397-1934
6.
11
Install hydraulic motor head assembly (11).
397-1933
0320 00-5
TM 5-3805-261-23-2
0320 00
7.
Install new seal assembly (10) and ring (8) on piston

(9).
9
10
397-1932
8.
Install linear actuator assembly (7).
9.
Apply thread lubricant to threads of bolt (5).
10.
Install bolt (5) and washer (6). Torque bolt to 720 to

880 lb-ft (976 to 1,193 Nm).
397-1931
11.
Lubricate outside of bearing (1), inside of linear actuator cap assembly (3), and inside of cylinder tube (2)
thoroughly with hydraulic oil.
12.
Install cylinder tube (2).
1
4
NOTE
Tighten linear actuator cap with cylinder
shaft fully extended. This will keep cylinder, piston, and head in alignment.
13.
Tighten linear actuator cap assembly (3) to 450 lb-ft

(610 Nm) on cylinder tube (2).
14.
Install bearing (1) and two rings (4).
15.
Install steering cylinder (WP 0176 00).
397-1930
END OF WORK PACKAGE

0320 00-6
TM 5-3805-261-23-2
STEERING VALVE MAINTENANCE (DUAL VALVE DESIGN)
0321 00

INITIAL SETUP
Maintenance Level
References
WP 0020 00
Direct Support
WP 0216 00

0348 00)
Wood block
Materials/Parts
Engine off (TM 5-3805-261-10)

Hoses disconnected (WP 0171 00)
0321 00-1
TM 5-3805-261-23-2
STEERING VALVE MAINTENANCE (DUAL VALVE DESIGN) - CONTINUED
0321 00
REMOVAL
CAUTION
NOTE
The following is a maintenance procedure for the left steering valve. The maintenance procedure for the
right steering valve is identical.
Remove three bolts (3), washers (2), and left steering
valve (1).
1
2
397-545
DISASSEMBLY
1.
Evenly loosen four bolts (11) to relieve spring (6).
2.
Remove four bolts (11) and valve head (10) from

relief valve body assembly (4).
3.
Remove preformed packings (8 and 9) and shims (7).

Discard preformed packings.
4.
Remove spring (6) and valve disk (5).
5
6
7
8
9
11
10
397-4328
0321 00-2
TM 5-3805-261-23-2
STEERING VALVE MAINTENANCE (DUAL VALVE DESIGN) - CONTINUED
0321 00
5.
Remove plug (12) and preformed packing (19). Discard preformed packing.
6.
Remove four bolts (13) and valve head (14).
7.
Remove and discard two preformed packings (15 and

18).
8.
Remove seat (17).
18
9.
17
12
13
14
19
15
16
397-4329

ASSEMBLY
1.
2.
Install seat (17).
3.
Install two new preformed packings (18 and 15).
4.
Install valve head (14) and four bolts (13).
5.
6.
Install valve disk (5) and spring (6).
7.
Install shims (7) and new preformed packings (9 and 8).
8.
Install valve head (10) and four bolts (11) evenly on relief valve body assembly (4).
INSTALLATION
1.
Install left steering valve (1), three washers (2), and bolts (3).
2.
Connect hoses (WP 0171 00).
3.
4.
Turn steering wheel to the right while moving the machine slowly forward a few feet.
5.
Turn steering wheel to the left while moving the machine slowly forward a few feet.
6.
Repeat steps 13 and 14 at least five times to bleed air from system.
7.
Stop engine.
8.
Check for leaks.
9.
Refill hydraulic tank to proper level (WP 0216 00).
END OF WORK PACKAGE

0321 00-3/(-4 Blank)
TM 5-3805-261-23-2
STEERING VALVE MAINTENANCE (SINGLE VALVE DESIGN)
0322 00

INITIAL SETUP
Maintenance Level
References
WP 0020 00
Direct Support
WP 0216 00
0348 00)
Materials/Parts
Engine off (TM 5-3805-261-10)
O-ring
Hydraulic hoses, lines, and fittings disconnected

(WP 0169 00)
0322 00-1
TM 5-3805-261-23-2
STEERING VALVE MAINTENANCE (SINGLE VALVE DESIGN) - CONTINUED
0322 00
REMOVAL
CAUTION
1.
Remove three bolts (2), washers (3), and steering

valve (1).
2,3
397-2289
2.
Remove adapter (9).
3.
Remove O-ring (5), valves (7), shims (6), and spring

(8).
4.
Remove seat (4).
5.
Repeat steps 1 through 3 for bottom half of valve.
397-2290
1
ASSEMBLY
1.
Install new O-ring (5).
2.
Install seat (4).
3.
Install valves (7), shims (6), and spring (8) on steering valve (1).
4.
Install adapters (9).
5.
Repeat steps 1 through 4 for bottom half of valve.

0322 00-2
TM 5-3805-261-23-2
STEERING VALVE MAINTENANCE (SINGLE VALVE DESIGN) - CONTINUED

INSTALLATION
1.
Install steering valve (1), three washers (3), and bolts (2).
2.
Connect hydraulic hoses, lines, and fittings (WP 0169 00).
3.
4.
Turn steering wheel to the right while moving the machine slowly forward a few feet.
5.
Turn steering wheel to the left while moving the machine slowly forward a few feet.
6.
Repeat steps 4 and 5 at least five times to bleed air from system.
7.
Stop engine.
8.
Inspect hose assemblies and connections for leaks.
9.
Refill hydraulic tank to proper level (WP 0216 00).
END OF WORK PACKAGE
0322 00-3/(-4 Blank)
0322 00
TM 5-3805-261-23-2
COMBINATION VALVE MAINTENANCE
0323 00

Removal, Disassembly, Cleaning and Inspection, Testing, Assembly, Installation
INITIAL SETUP
References
Maintenance Level
Direct Support
WP 0020 00


0348 00)
Indicator, dial (Item 32, WP 0348 00)
Test, spring resiliency (Item 88, WP 0348 00)

Materials/Parts
Engine off (TM 5-3805-261-10)

O-ring (11)
Hydraulic tank drained (WP 0216 00)
Supplemental steering pressure switch disconnected (WP 0087 00)
Pin, cotter
WARNING
Lubricating/hydraulic oils, engine coolant, fuel, and other fluids used in the performance of maintenance can
be very slippery. Immediately wipe up any spills. Failure to follow this warning may cause injury to personnel
0323 00-1
TM 5-3805-261-23-2
COMBINATION VALVE MAINTENANCE - CONTINUED
0323 00
REMOVAL
CAUTION
NOTE
1.
Disconnect tube assembly (1) and remove O-ring (2). Discard O-ring.
2.
Remove connector (3) and preformed packing (4). Discard preformed packing.
397-546
3.
Disconnect hose assembly (16) and remove O-ring

(15) from bottom of valve. Discard O-ring.
4.
5.
Disconnect hose assembly (8) and remove O-ring (7).

Discard O-ring.
6.
7.

(10). Discard O-ring.
8.
0323 00-2
7 8
9
10
12
11
13
16
15
14
397-547
TM 5-3805-261-23-2
0323 00
REMOVAL - CONTINUED
9.

10.
17 18
19
20
397-548
11.

12.
21
22
23
24
397-549
13.

14.
25
26
27
28
397-550
0323 00-3
TM 5-3805-261-23-2
0323 00
REMOVAL - CONTINUED
15.
Remove three bolts (29), washers (30), bolts (34),

washers (33 and 32), and mountings (31).
30
29
31
34
16.
Remove spring (36), cotter pin (43), and pin (35). Discard cotter pin.
17.
Disconnect hose assembly (42) from elbow (40).
18.
Remove elbow (40), adapter (38), O-rings (39 and 41),

and preformed packing (37). Discard preformed packing and O-ring.
33
32
397-551
35
36
43
37
38 39 41 42
40
397-552
0323 00-4
TM 5-3805-261-23-2
0323 00
REMOVAL - CONTINUED
19.
Disconnect hose (51) and remove O-ring (50) from tee

20.
Disconnect hose (46) and remove O-ring (45) from tee

21.
Remove tee (44), adapter (47), valve (48), and preformed packing (49). Discard preformed packing.
45
46
44
47
48
49
50
51
397-553
52
22.
23.
Remove connector (60), O-ring (58), and preformed

packing (57). Discard preformed packing and O-ring.
24.
25.
Remove connector (54), O-ring (53), and preformed

packing (55). Discard preformed packing and O-ring.
26.
Remove combination valve (56).
27.
Remove all fittings, adapters, preformed packings, and

O-rings. Discard O-rings and preformed packings.
53 54
55
60
59
56
58
57
397-554
0323 00-5
TM 5-3805-261-23-2
0323 00
DISASSEMBLY
1.
Remove three bolts (61).
2.
Remove unloader valve assembly (65) from valve

body assembly (62).
3.
Remove and discard preformed packings (63, 64, 66,

and 67).
61
65 66 67
62
64
63
397-4330
4.
Remove two bolts (71), washers (68), boot (70), and

manual control lever assembly (69).
71
68
69
70
397-4331
0323 00-6
TM 5-3805-261-23-2
0323 00
5.
6.
Remove housing (74), preformed packing (80), bearing (79), ring (78), preformed packing (77), lever (76),
and bearing (75). Discard preformed packings.
72
73
Remove nut (72) and threaded ring (73) from housing

(74).
74
75
76
77 78
79
80
397-4332
7.
8.
9.
10.
Remove nut (87), washer (86), and elbow (88).
11.

body (83). Discard preformed packing.
81
82
83
92
91
84
90
89
85
86
87
88
397-4333
0323 00-7
TM 5-3805-261-23-2
0323 00
12.
Remove plug (95), preformed packing (94), and stem

assembly (93). Discard preformed packing.
93
94
95
13.
Compress spring (98).
14.
Remove two retainers (99), spring (98), and washer

(97) from stem (96).
397-4334
96
97
99
98
397-4335
0323 00-8
TM 5-3805-261-23-2
0323 00
NOTE
Retain shims for reassembly.
15.
Remove plug (105), preformed packing (104), retainer

(103), shims (102), spring (101), and valve (100). Discard preformed packing.
16.
Remove plug (106), preformed packing (107), springs

(108 and 109), and valve stop assembly (110). Discard
preformed packing.
110
100
101
109
108
102
103
107
106
104
105
397-4336
NOTE
Retain shims for reassembly.
17.
Remove washer (113) and shims (112) from stop

(111).
111
112
113
0323 00-9
397-4337
TM 5-3805-261-23-2
0323 00
18.
Remove plug (114), preformed packing (115), spacer

(116), preformed packing (117), spacer (118), valve
(119), spring (120), body (121), and seat (122). Discard preformed packings.
114
115
116
117
118
119
120
121
122
397-4338
19.
Remove plug (123), preformed packing (124), piston

(125), and stem assembly (126). Discard preformed
packing.
123
124
20.
125
128
127
126
397-4339
0323 00-10
TM 5-3805-261-23-2
0323 00
21.
22.
Remove elbow (133) and preformed packing (134).

23.
Remove elbow (132) and preformed packing (131)

from body (130). Discard preformed packing.
24.
Remove supplemental steering pressure switch (WP

0087 00).
129
130
131
132
135
133
134
397-4340

TESTING
NOTE
Replace springs if broken, collapsed, have twisted coils, or are out of tolerance.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Use spring tester and torque wrench to apply test load to spring (98). Test load is 24.99 to 27.61 lb (11.34 to 12.52 kg).
Measure length of spring (98). Test length is 1.53 in. (3.89 mm).
Remove test load.
Measure free length of spring (98). Free length should be 2.375 in. (6.03 mm).
Use spring tester and torque wrench to apply test load to spring (101). Test load is 64 to 70 lb (29 to 32 kg).
Measure length of spring (101). Test length should be 1.43 in. (3.63 mm).
Remove test load.
Remove test load.
98,101,108
98,101,108
TEST LENGTH
TEST LENGTH
397-4341
397-2300
0323 00-11
TM 5-3805-261-23-2
0323 00
TESTING - CONTINUED
13.
14.
Measure length of spring (109). Test length should be 1.66 in. (4.22 cm).
15.
Remove test load.
16.
Measure free length of spring (109). Free length should be 2.46 in. (6.25 cm).
17.
Use spring tester and torque wrench to apply test load to spring (120). Test load is 8 lb (3.6 kg).
18.
19.
Remove test load.
20.
Measure free length of spring (120). Free length should be 1.2 in. (3.0 cm).
109,120
109,120
TEST LENGTH
TEST LENGTH
397-2300
397-2299
ASSEMBLY
1.
Install supplemental steering pressure switch (WP

0087 00).
2.
Install new preformed packing (131) and elbow (132)

in body (130).
3.
4.
129
130
131
132
135
133
134
0323 00-12
397-4340
TM 5-3805-261-23-2
0323 00
5.
6.
123
124
Install stem assembly (126), piston (125), new preformed packing (124), and plug (123).
125
128
127
126
397-4339
7.
Install seat (122), body (121), spring (120), valve

(119), spacer (118), new preformed packing (117),
spacer (116), new preformed packing (115), and plug
(114).
114
115
116
117
118
119
120
121
122
397-4338
0323 00-13
TM 5-3805-261-23-2
0323 00
8.
Install shims (112) and washer (113) to stop (111).
111
112
113
9.
Install valve stop assembly (110), springs (108 and

109), new preformed packing (107), and plug (106).
10.
Install valve (100), spring (101), shim (102), retainer

(103), new preformed packing (104), and plug (105).
397-4337
110
100
101
109
11.
Install washer (97) and spring (98) on stem (96).
12.
13.
Install two retainers (99).
108
102
103
107
106
104
105
397-4336
96
97
99
98
397-4335
0323 00-14
TM 5-3805-261-23-2
0323 00
14. Install stem assembly (93), new preformed packing
(94), and plug (95).
93
94
95
15.
Install new preformed packing (90) and plug (89) in

body (83).
16.
Install elbow (88), washer (86), and nut (87).
17.
18.
19.
81
397-4334
82
83
92
91
84
90
89
85
86
87
88
397-4333
0323 00-15
TM 5-3805-261-23-2
0323 00
20.
Install new preformed packings (77 and 80), ring (78),

and bearings (75 and 79) on lever (76).
21.
Install housing (74).
74
75
76
77
78
79
80
397-4343
NOTE
Place unloader valve in vise.
22.
23.
Install manual control lever assembly (69), two washers (68), and bolts (71) in unloader valve assembly
(65).
65
69
73
71
68
Install threaded ring (73).
397-4344
0323 00-16
TM 5-3805-261-23-2
0323 00
24.
Lift lever (76) with a force of 25 lb (11.3 kg) using a spring scale.
25.
Adjust threaded ring (73). Turn threaded ring in or out until end play of lever (76) is 0.003 to 0.009 in. (0.076 to 0.23
mm).
25 LB
LIFT
SPRING SCALE
76
73
0.003 TO 0.009 IN.
76
397-4345
397-2498
26.
Install nut (72) and boot (70).
27.
Install new preformed packings (63, 64, 66, and 67),

unloader valve assembly (65) with valve body assembly (62), and three bolts (61).
61
70
65
72
66
62
64
63
67
397-4346
0323 00-17
TM 5-3805-261-23-2
0323 00
INSTALLATION
52
1.
Position combination valve (56).
2.
Install new preformed packing (55) and connector

(54).
3.
Install new O-ring (53) and connect hose assembly

(52).
4.
Install new preformed packing (57) and connector

(60).
5.

(59) to connector (60).
53
54
55
60
59
56
58
57
397-554
6.
Install new preformed packing (49), new O-rings (45

and 50), valve (48), adapter (47), and tee (44).
7.
Connect hose assembly (46) to tee (44).
8.
Connect hose assembly (51) to tee (44).
45
46
44
51
47
48
49
50
397-553
0323 00-18
TM 5-3805-261-23-2
0323 00
9.
Install new preformed packing (37), adapter (38), new

O-ring (39), and elbow (40).
10.

(42) to elbow (40).
11.
Install pin (35), new cotter pin (43), and spring (36).
35
36
43
37
38 39 41 42
40
397-552
12.
Install three mountings (31), washers (33 and 32),

bolts (34), washers (30), and bolts (29).
30
29
31
34
0323 00-19
33
32
397-551
TM 5-3805-261-23-2
0323 00
13.
14.

(25).
25
26
27
28
397-550
15.
16.

(21).
21
22
23
24
397-549
17.
18.

(20).
17 18
19
20
397-548
0323 00-20
TM 5-3805-261-23-2
0323 00
19.
20.

(11).
21.
22.
Install new O-ring (7) and connect hose assembly (8).
23.
24.

(16).
25.
Install new preformed packing (4) and connector (3).
26.
Install new O-ring (2) and connect tube assembly (1).
7 8
9
10
12
16
15
11
13
14
397-547
397-546
27.
Install supplemental steering pressure switch (WP 0087 00).
28.
Fill hydraulic tank to proper level (WP 0216 00).
29.
30.
Turn steering wheel to the left and right while moving the machine slowly forward a few feet.
31.
Repeat step 29 at least five times to bleed air from system.
32.
Stop engine.
33.
Inspect hose assemblies and connections for leaks.
END OF WORK PACKAGE
0323 00-21/(-22 Blank)
TM 5-3805-261-23-2
FRAME SEPARATION AND CONNECTION REPLACEMENT (CCE AND TYPE I MACHINES)
0324 00

INITIAL SETUP
Maintenance Level
Direct Support

0182 00)

Engine coolant drained (WP 0024 00)

0348 00)
Wheel lean lock bolt installed (TM 5-3805-261-10)
Hydraulic pump drive shaft removed (WP 0232 00)
Jack stand (Item 84, WP 0348 00)
Seat removed (CCE Machine) (WP 0200 00)
Supplemental steering lines to hydraulic tank disconnected (WP 0172 00 and WP 0173 00)
Bolt, 5/8-11NC x 6 (2)

Heavy-duty forklift truck
Hydraulic hose disconnected at hydraulic tank

(0250 00)
Pusher bolt, 3/8-16NC (2)

Wood block
Oil cooler to hydraulic pump relief valve disconnected (0250 00)
Materials/Parts
Hydraulic line disconnected at relief valve (0250

00)

Lockwasher (36)
Disconnect switch cable disconnected at starting

motor and mounting hardware removed (WP
0142 00)
Pin, cotter
Personnel Required
Main harness disconnected from all items in engine

compartment and mounting hardware removed
(0286 00)
Two
References
WP 0020 00
Blackout light harness disconnected from rear

blackout lights and mounting hardware removed
(WP 0287 00)
WP 0152 00
WP 0212 00
Engine off (TM 5-3805-261-10)
Supplemental steering harness disconnected from

all items in engine compartment and mounting
hardware removed (WP 0290 00)
EMS harness disconnected from all items in engine
compartment and mounting hardware removed
(WP 0291 00)
Air brake lines disconnected from brake control
valve (WP 0161 00)
Front pin of articulation cylinder disconnected (WP
0336 00)
0324 00-1
TM 5-3805-261-23-2
FRAME SEPARATION AND CONNECTION REPLACEMENT

(CCE AND TYPE I MACHINES) - CONTINUED
0324 00
REMOVAL
1.
Remove two nuts (1), washers (2), clip (3), plate (4), and clamp (5).
3
4
397-1937
2.
Remove two nuts (6), washers (7), clip (8), plate (9),
and clamp (10) from under left-rear of cab.
10
8
9
0324 00-2
7
397-1938
TM 5-3805-261-23-2

0324 00
REMOVAL - CONTINUED
3.
Remove two nuts (15), washers (14), clip (13), plate (11), and clamp (12).
11
15
12
14 13
397-1939
4.
Remove two nuts (20), washers (16), clip (19), plate

(18), and clamp (17) from under right-rear of cab.
16
20
0324 00-3
19
18
17
397-1940
TM 5-3805-261-23-2

0324 00
REMOVAL - CONTINUED
5.
6.
Loosen three nuts (23) and slide back on control cable assemblies (24, 25, and 26).
22
21
25
26
24
23
7.
397-1941
Slide back retainer (27) and three couplings (29) on cable assemblies (24, 25, and 26).
NOTE
Tag wire, cable, and harness assemblies before disconnecting to aid in installation.
8.
9.
Separate three cable assemblies (24, 25, and 26) from

transmission control valves (28) (WP 0152 00).
25
Pull cable assemblies (24, 25, and 26) forward from

engine compartment and position cable assembly (26)
alongside left side of cab and cable assemblies (24 and
25) alongside right side of cab.
27
28
24
0324 00-4
26
397-1942
29
TM 5-3805-261-23-2

0324 00
REMOVAL - CONTINUED
10.
Remove bolt (37), washer (38), and clip (39) (WP 0212 00).
11.
Remove clamp (32) and position heater hose (33) to rear of machine.
12.
Remove clamp (30) and position heater hose (31) to rear of machine.
13.
Remove cotter pin (35) and pin (34) from articulation indicator linkage (36). Discard cotter pin.
30
31
34
39
32
38
35
36
33
37
397-1943
14.
Position forklift at rear frame of machine.
15.
Position two jack stands under operators platform on each side of machine.
16.
Position all wire, cable, and harness assemblies on

front of machine.
17.
Position all hose assemblies on rear of machine.
18.
Position wood blocks under front wheels so that

wheels cannot move.
19.
Remove four bolts (40) and lockwashers (41) from

four corners of plate (42). Discard lockwashers.
40
41
42
397-1944
0324 00-5
TM 5-3805-261-23-2

0324 00
REMOVAL - CONTINUED
20.
43
Install two 3/8-16NC pusher bolts (43) in plate (42)

and pin (44). Tighten pusher bolts alternately to
remove pin and plate
NOTE
42
Lift or lower rear frame with forklift to

remove any pressure from pin assembly.
21.
Remove two 3/8-16NC pusher bolts (43).
44
397-1945
22.
45
Remove two bolts (45), lockwashers (47), and plate

(46) from pin (44). Discard lockwashers.
47
46
44
397-1946
23.
Remove four bolts (51), lockwashers (52), six bolts

(50), lockwashers (49), plate (53), and shim(s) (48).
Tie shim(s) together and tag for identification. Discard
lockwashers.
48
53
49
52
51
0324 00-6
50
397-1947
TM 5-3805-261-23-2

0324 00
REMOVAL - CONTINUED
24.
Use a hydraulic jack to remove bottom pin (54).
54
HYDRAULIC
JACK
397-1948
25.
Remove spacer (55).
55
397-1949
0324 00-7
TM 5-3805-261-23-2

0324 00
REMOVAL - CONTINUED
CAUTION
NOTE
Separation of frames is not possible

until spacer has been removed.
26.
Disconnect hose (57) and attach shop air supply line to

elbow (58) on parking brake actuator (56).
27.
Release parking brake by applying air pressure to

parking brake actuator (56).
57
56
58
397-1950
28.
Separate rear frame (59) from front frame (60) by

moving rear frame rearward with forklift.
29.
Install jack stands under radiator end of rear frame and

remove forklift.
30.
Remove shop air supply line.
59
60
397-1951
0324 00-8
TM 5-3805-261-23-2

0324 00

Clean and inspect all parts in accordance WP 0020 00.
INSTALLATION
1.
Position forklift under rear frame and remove jack stands.
2.
Apply shop air supply line to elbow (58) on parking brake actuator (56) and release parking brake
3.
Move rear frame (59) into position on front frame (60) using forklift.
4.
Use forklift to lift or lower rear frame (59) and hydraulic jack to move frame from side to side. Align bottom pin bore of
rear frame with pin bore of front frame (60).
45
47
55
46
44
53
49
50
397-1953
NOTE
Install plate to hold spacer in place.
5.
Install spacer (55), plate (53), six bolts (50), and new
lockwashers (49).
6.
Lower temperature of pin (44) and install plate (46),

two new lockwashers (47), and bolts (45).
0324 00-9
397-1946
TM 5-3805-261-23-2

0324 00
7.
Install four new lockwashers (41) and bolts (40).

Cross tighten four bolts to 75 lb-ft (102 Nm). Tighten
one of four bolts to 75 lb-ft (102 Nm). Tighten one of
four bolts in the upper right corner of plate (42), then
tighten the next of four bolts in the lower left corner.
Tighten two remaining of four bolts.
40
41
42
397-1944
8.
Position pin (54).
54
397-1954
0324 00-10
TM 5-3805-261-23-2

0324 00
NOTE
Use two 5/8-11NC x 6 bolts to keep holes in bottom of pin in alignment with holes in plate.
9.
Install two 5/8-11NC x 6 bolts (60), through plate (53)

and into pin (54).
10.
Install pin (54) completely.
11.
Remove two 5/8-11NC x 6 bolts (60).
54
53
60
397-1955
12.
Install six bolts (50), lockwashers (49), and plate (53).

13.
Install four new lockwashers (52), bolts (51), and plate

(53). Tighten bolts to 100 lb-ft (136 Nm).
53
49
52
50
51
0324 00-11
397-1956
TM 5-3805-261-23-2

0324 00
14.
Measure distance between plate (53) and rear frame (59) with a feeler gauge. Measure distance at each of four bolt locations.
15.
Remove four bolts (51), lockwashers (52), and plate (53). Discard lockwashers.
59
53
53
51
52
51
397-1958
16.
397-1957
Install a thickness of shim(s) (48) (same as minimum

distance measured in step 14 minus 0.010 in. [0.25
mm], plate (53), six new lockwashers (49), bolts (50),
four new lockwashers (52), and bolts (51).
48
53
49
52
51
0324 00-12
50
397-1947
TM 5-3805-261-23-2

0324 00
17.
Disconnect shop air supply line from elbow (58) on

parking brake actuator (56) and connect hose (57).
57
56
58
397-1952
18.
Remove jack stands and forklift from machine.
19.
Install pin (34) and new cotter pin (35) on articulation

indicator linkage (36).
36
34
35
397-1960
0324 00-13
TM 5-3805-261-23-2

0324 00
20.
Position heater hose (31) on heater and install clamp

(30) (WP 0192 00).
21.
Position heater hose (33) and install clamp (32).
22.
30
31
32
39
38
33
37
397-1962
23.
Position cable assemblies (24, 25, and 26) on machine (WP 0152 00).
24.
Set cable assemblies (24, 25, and 26) into transmission control valves (28).
25.
Move three couplings (29) forward on cable assemblies (24, 25, and 26) and position over transmission control valves
(28).
26.
Slide retainer (27) forward.
27.
Install three nuts (23). Tighten three nuts.
28.
22
21
25
26
27
25
26
28
24
24
397-1942
29
23
0324 00-14
397-1941
TM 5-3805-261-23-2

0324 00
29.
Install clamp (17), plate (18), clip (19), two washers

(16), and nuts (20) under right-rear of cab.
16
20
30.
Install clamp (12), plate (11), clip (13), two washers

(14), and nuts (15) under right-front of engine compartment.
19
11
15
18
17
397-1940
12
14 13
397-1939
0324 00-15
TM 5-3805-261-23-2

0324 00
31.
Install clamp (10), plate (9), clip (8), two washers (7),
and nuts (6) under left-rear of cab.
10
32.
397-1938
Install clamp (5), plate (4), clip (3), two washers (2),
and nuts (1) under left-front of engine compartment.
397-1937
0324 00-16
TM 5-3805-261-23-2

0324 00
33.
Connect front pin of articulation cylinder (WP 0336 00).
34.
Connect air brake lines to brake control valve (WP 0161 00).
35.
Install mounting hardware and connect EMS harness to all items in engine compartment (WP 0291 00).
36.
Install mounting hardware and connect supplemental steering harness to all items in engine compartment (WP 0290 00).
37.
Install mounting hardware and connect blackout light harness to all items in engine compartment (WP 0287 00).
38.
Install mounting hardware and connect main harness to all items in engine compartment (WP 0286 00).
39.
Install mounting hardware and connect disconnect switch cable at starting motor (WP 0142 00).
40.
Connect hydraulic line at relief valve (WP 0250 00).
41.
Connect oil cooler to hydraulic pump relief valve (WP 0250 00).
42.
Connect hydraulic hose at hydraulic tank (WP 0250 00).
43.
Connect supplemental steering lines to hydraulic tank (WP 0172 00 and WP 0173 00).
44.
Fill engine coolant (WP 0024 00).
45.
Install seat (WP 0200 00).
46.
Install hydraulic pump drive shaft (WP 0232 00).
47.
Remove wheel lean lock bolt (TM 5-3805-261-10).
48.
49.
END OF WORK PACKAGE
0324 00-17/(-18 Blank)
TM 5-3805-261-23-2
ARTICULATION HITCH BEARING REPLACEMENT (CCE AND TYPE I MACHINES)
0325 00

INITIAL SETUP
Maintenance Level
Materials/Parts
Grease (Item 17, WP 0349 00)
Direct Support

Lockwasher (7)

0348 00)
Seal (2)

References
WP 0020 00
Bolt, machine (2) (Item 14, WP 0348 00)

Nut, plain, hexagon (Item 46, WP 0348 00)
Engine off (TM 5-3805-261-10)

Ring installer (Item 68, WP 0348 00)
Washer flat (Item 91, WP 0348 00)
Frame halves separated (WP 0324 00)
0325 00-1
TM 5-3805-261-23-2
ARTICULATION HITCH BEARING REPLACEMENT (CCE AND TYPE I MACHINES) - CONTINUED
0325 00
REMOVAL
1.
Remove fitting (2), spacer (1), seven bolts (5), lockwashers (4), and cap (3). Discard lockwashers.
1
4
5
FRONT FRAME
3
2
8
397-1966
LOWER PIN BORE
2.
Remove and discard seal (6) from cap (3).
6
397-1967
0325 00-2
TM 5-3805-261-23-2
0325 00
REMOVAL - CONTINUED
NOTE
Tie shim(s) together and tag for identification to aid in installation.
Inspect bearings before removing. Remove bearings only if inspection indicates replacement is necessary.
3.
Remove shim(s) (8) and bearing (7).
4.
Remove cap (9) and seal (10) from bottom of lower

pin bore. Discard seal.
FRONT FRAME
7
10
9
5.
Use puller adapters, nut, washer, hydraulic puller, and

ring installer to remove collar (11) from upper pin
bore of front frame.
6.
Inspect bearing (12). Replace if cracked, broken, distorted, gouged, or excessively worn.
7.
Use puller adapters, nut, washer, hydraulic puller, and

two bolts to remove bearing (12), if necessary.
LOWER PIN BORE
397-1968
11
FRONT
FRAME
12
UPPER PIN BORE

397-1970
0325 00-3
TM 5-3805-261-23-2
0325 00
REMOVAL - CONTINUED
8.
Remove and discard two seals (14) from upper pin

bore of rear frame.
9.
Inspect bearing (13). Replace if cracked, broken, distorted, gouged, or excessively worn.
10.
Use nut, washer, hydraulic puller, ring installer, and

puller assembly to remove bearing (13), if necessary.
13
14
REAR
FRAME
UPPER PIN BORE
397-1971

INSTALLATION
1.
Use hydraulic puller, puller assembly, washer, and nut to install new bearing (13), if removed, to a depth of 0.5 in. (13
mm) from each surface of upper pin bore of rear frame.
2.
Use clean grease to lubricate two new seals (14).
3.
Use drive plate and hammer to install two new seals (14) with lips toward the outside surface in upper pin bore of rear
frame.
4.
If bearing (12) was removed, lower temperature of

new bearing (12).
5.
Use puller adapter, hydraulic puller, washer, nut, two

bolts, and two adapters to install new bearing (12), if
removed, in upper pin bore of front frame.
6.
Use hydraulic puller, puller assembly, washer, nut, two

bolts, and two adapters to install collar (11) in upper
pin bore of front frame.
11
FRONT
FRAME
12
UPPER PIN BORE

397-1970
0325 00-4
TM 5-3805-261-23-2
0325 00
7.
Use clean grease to lubricate new seal (10) and position with lip facing down on cap (9).
8.
Use drive plates and hammer to install new seal (10)

on cap (9).
DRIVE PLATE
10
397-1972
9.
Install bearing (7) in cap (9) and position under lower

pin bore of front frame.
FRONT
FRAME
7
9
LOWER PIN BORE
0325 00-5
397-1973
TM 5-3805-261-23-2
0325 00
10.
Install bearing (7) and cap (9), together, in lower pin

bore.
FRONT FRAME
7,9
11.
Use clean grease to lubricate new seal (6) and position

with lip facing down on cap (3).
12.
Use drive plates and hammer to install new seal (6) on

cap (3).
LOWER PIN BORE
397-1974
DRIVE PLATE
0325 00-6
397-1972
TM 5-3805-261-23-2
0325 00
13.
Position cap (3) over bearing (7) on top of lower pin

14.
Install three of seven new lockwashers (4) and three of

seven bolts (5) through caps (3). Ensure there is at
least one hole between each of the three bolts (5).
15.
Position cap (3) on bearing (7). Do not install shims at

this time.
16.
Evenly and gradually tighten each bolt (5) to 65 lb-ft

(88 Nm).
17.
Ensure cap (3) is even with bottom of frame.
5
4
3
FRONT FRAME
LOWER PIN BORE
18.
Use feeler gauge to measure distance between front

frame and upper cap (3). Check distance at each bolt
(5) location.
397-1975
5
FRONT FRAME
FEELER GAUGE
397-1976
0325 00-7
TM 5-3805-261-23-2
0325 00
19.
Install next three of seven bolts (5) and new lockwashers (4) to cap (3).
20.
Install shim(s) (8) equal to smallest measurement.
21.
Position cap (3) over bearing (7) on top of lower pin

22.
Install last of seven bolts (5) and new lockwasher (4).
23.
Evenly and gradually tighten seven bolts (5) to 75 lb-ft

(102 Nm).
24.
Install spacer (1) on bearing (7).
25.
Install fitting (2).
26.
Use clean grease to lubricate fitting (2) (WP 0020 00).
1
5
4
3,6
FRONT
FRAME
2
8
27.
Connect assembly frame halves (WP 0324 00).
END OF WORK PACKAGE
0325 00-8
LOWER
PIN BORE
397-1978
TM 5-3805-261-23-2
ARTICULATION HITCH BEARING REPLACEMENT (TYPE II MACHINE)
0326 00

INITIAL SETUP
Maintenance Level
References
WP 0020 00
Direct Support


0348 00)

Materials/Parts
Engine off (TM 5-3805-261-10)
Lockwasher (17)
Seal (4)
Machine sectionalized (TM-5-3805-261-10)
0326 00-1
TM 5-3805-261-23-2
ARTICULATION HITCH BEARING REPLACEMENT (TYPE II MACHINE) - CONTINUED
0326 00
DISASSEMBLY
1.
Remove fitting (1), bolts (2 and 9), lockwashers (3 and 8), and cover (7). Discard lockwashers.
2.
Remove collar (6) and pin (5).
3.
Remove shim (4).
4.
Remove seals (10 and 12) and bearing (11). Discard seals.
9
10
2
8
11
12
6
5
4
397-2407
5.
Remove bolts (28 and 29), lockwashers (27 and 30), retaining plate (26), shim (25), sleeve spacer (24), and pin (23).
6.
Remove bolts (14), lockwashers (15), cap and fitting (21 and 22), spacer (13), seal (16), shim (20), bearing (19), seal
(17) and cap (18). Discard seals and lockwashers.
0326 00-2
TM 5-3805-261-23-2
ARTICULATION HITCH BEARING REPLACEMENT (TYPE II MACHINE) - CONTINUED
0326 00
23
13
14
24
25
15
21
22
26
30
29
27
28
16
20
17
19
18
397-2408

ASSEMBLY
1.
Install cap (18), new seal (17), bearing (19), shim (20), new seal (16), spacer (13), cap and fitting (21 and 22), new lockwashers (15), and bolts (14).
2.
Install pin (23), sleeve spacer (24), shim (25), retaining plate (26), new lockwashers (27 and 30), and bolts (28 and 29).
3.
Install bearing (11) and new seals (10 and 12).
4.
Install shim (4).
5.
Install pin (5) and collar (6).
6.
Install cover (7), new lockwashers (3 and 8), bolts (2 and 9), and fitting (1).
7.
Reassemble machine (TM 5-3805-261-10).
END OF WORK PACKAGE

0326 00-3/(-4 Blank)
TM 5-3805-261-23-2
ROPS REPLACEMENT (CCE MACHINE)
0327 00

INITIAL SETUP
Maintenance Level
Direct Support
Blade float valve harness removed (WP 0133 00)
Front defroster lead removed (WP 0134 00)

0348 00)
Branch, link (Item 12, WP 0348 00)
Rear defroster lead removed (WP 0135 00)

Front work light lead removed (WP 0136 00)
Cab signal light lead removed (WP 0107 00)

Dome light resistor harness removed (WP 0140 00)
Right and left blade float harness removed (WP

0144 00)
Eyebolt, (2) 3/4-10

Front lower cab windows removed (WP 0186 00)
Materials/Parts
Left and right cab doors removed (WP 0188 00)
Lower front and rear cab sound suppression panels

References
Ceiling cab sound suppression panels removed (WP

0191 00)
WP 0020 00
Personnel Required
Rear cab sound suppression panels removed (WP

0192 00)
Three
Lower front wiper removed (WP 0206 00)
Upper front wipers removed (WP 0207 00)
Rear wiper removed (WP 0208 00)
Windshield washers removed (WP 0209 00)
Engine off (TM 5-3805-261-10)
Front and rear defroster fans removed (WP 0210

00)
Outside sideview mirror removed (WP 0214 00)
Dome light resistor removed (WP 0100 00)
ROPS accessories removed (WP 0185 00)
Front work lights removed (WP 0105 00)

Cab signal lights removed (WP 0107 00)
Cab storage compartment removed (WP 0189 00)
Dome light removed (WP 0111 00)
Cab main harness removed (WP 0292 00)
0327 00-1
TM 5-3805-261-23-2
ROPS REPLACEMENT (CCE MACHINE) - CONTINUED
0327 00
REMOVAL
1.
Install two 3/4-10 eyebolts (1) in top of ROPS (2).
WARNING
NOTE
ROPS weighs 2,058 lb (934 kg).

2.
Attach sling to two 3/4-10 eyebolts (1) on front of

ROPS (2).
397-4347
3.
Remove two nuts (5), washers (4), and bolts (3) from
two front corners of operators cab.
4
5
0327 00-2
397-4348
TM 5-3805-261-23-2
0327 00
REMOVAL - CONTINUED
4.
Remove six bolts (7) and retainers (6) from right and
left sides of cab.
6
7
397-4349
5.
Install two link brackets to ROPS (2).
6.
Use sling to remove ROPS (2).
7.
Remove four mounts (9) and two bushings (8).
9
8
397-4350
0327 00-3
TM 5-3805-261-23-2
0327 00
REMOVAL - CONTINUED
8.
Inspect two pads (11) and pad (10).
9.
Remove two pads (11) and pad (10) from ROPS (2).
Discard pads if damaged.
10.
Lower ROPS (2) onto level surface.
10
11
12
11.
Remove sling.
12.
Inspect two pads (12 and 14) and pad (13).
13.
Remove two pads (12 and 14) and pad (13). Discard
two pads (12 and 14) if damaged.
12
13
14
397-4352

0327 00-4
397-4351
TM 5-3805-261-23-2
0327 00
INSTALLATION
1.
Position pad (13) and two pads (12 and 14).
WARNING
NOTE
ROPS weigh 2,058 lb (964 kg).
2.
Attach sling to ROPS (2).
3.
Raise ROPS (2).
4.
Install pad (10) and two pads (11).
5.
Position two bushings (8) and four mounts (9).
6.
Lower ROPS (2) to within 0.5 in. (12.7 mm) of operators platform.
9
8
397-4350
0327 00-5
TM 5-3805-261-23-2
0327 00
CAUTION
Do not lower ROPS onto operators platform and slide to align bolts. This improper procedure could result
in damage to pads. Any significant damage to pads could cause high sound levels for the operator.
7.
Install six bolts (7) and retainers (6), starting six bolts
by hand and partially tightening.
6
7
397-4349
NOTE
Holes for two bolts must be aligned before

bolts can be tightened to proper torque.
8.
Install two bolts (3), washers (4), and nuts (5) in two
front corners of cab. Tighten bolts to 870 lb-ft (1,180
Nm).
4
5
9.
397-4348
Tighten six bolts (7) to 870 lb-ft (1,180 Nm).
7
397-4353
0327 00-6
TM 5-3805-261-23-2
0327 00
10.
Remove sling.
11.
Remove two 3/4-10 eyebolts (1) from ROPS (2).
12.
Remove two link brackets
397-4347
13.
Install cab main harness (WP 0292 00).
14.
Install cab storage compartment (WP 0189 00).
15.
Install ROPS accessories (WP 0185 00).
16.
Install outside sideview mirror (WP 0214 00).
17.
Install front and rear defroster fans (WP 0210 00).
18.
Install windshield washers (WP 0209 00).
19.
Install rear wiper (WP 0208 00).
20.
Install upper front wipers (WP 0207 00).
21.
Install lower front wiper (WP 0206 00).
22.
Install rear cab sound suppression panels (WP 0192 00).
23.
Install ceiling cab sound suppression panels (WP 0191 00).
24.
Install lower front and rear cab sound suppression panels (WP 0190 00).
25.
Install left and right cab doors (WP 0188 00).
26.
Install front lower cab windows (WP 0186 00).
27.
Install right and left blade float harness (WP 0144 00).
28.
Install dome light resistor harness (WP 0140 00).
29.
Install cab signal light lead (WP 0107 00).
30.
Install front work light lead (WP 0136 00).
31.
Install rear defroster lead (WP 0135 00).
32.
Install front defroster lead (WP 0134 00).
33.
Install blade float valve harness (WP 0133 00).
34.
Install dome light (WP 0111 00).

0327 00-7
TM 5-3805-261-23-2

35.
Install cab signal lights (WP 0107 00).
36.
Install front work lights (WP 0105 00).
37.
Install dome light resistor (WP 0100 00).
38.
END OF WORK PACKAGE
0327 00-8
0327 00
TM 5-3805-261-23-2
OPERATORS PANEL CONSOLE BASE REPLACEMENT
0328 00

INITIAL SETUP
Maintenance Level
Direct Support

Materials/Parts
Engine off (TM 5-3805-261-10)
References
WP 0020 00
Operators panel console removed (WP 0193 00)

Transmission control group assembly removed (WP
0151 00)
0328 00-1
TM 5-3805-261-23-2
OPERATORS PANEL CONSOLE BASE REPLACEMENT - CONTINUED
0328 00
REMOVAL
1.
Remove four bolts (3), washers (4), and brackets (1 and 5).
2.
Remove four spacers (6 and 7).
NOTE
Remove seals only if inspection indicates replacement is necessary.
3.
If necessary, remove two seals (2).
2
3
4
7
5
397-2361
0328 00-2
TM 5-3805-261-23-2
OPERATORS PANEL CONSOLE BASE REPLACEMENT - CONTINUED
0328 00
REMOVAL - CONTINUED
4.
Remove base (8) and four mountings (9).
5.
Remove pad (10).
8
10
397-4355

INSTALLATION
1.
Install pad (10).
2.
Install four mountings (9) and base (8).
3.
Install two new seals (2), if removed.
4.
Install four spacers (6 and 7).
5.
Install brackets (5 and 1), four washers (4), and bolts (3).
6.
Install operators panel console (WP 0193 00).
7.
Install transmission control group assembly (WP 0151 00).
END OF WORK PACKAGE
0328 00-3/(-4 Blank)
TM 5-3805-261-23-2
HYDRAULIC PUMP ASSEMBLY AND MOUNTING REPLACEMENT
0329 00

INITIAL SETUP
References
Maintenance Level
Direct Support
WP 0020 00



Wood blocks
Materials/Parts
Engine off (TM 5-3805-261-10)
Cleaning compound, solvent (Item 8, WP 0349 00)

Machine articulated right (TM 5-3805-261-10)
Install pivot locking pin (TM 5-3805-261-10)

Hydraulic tank removed (WP 0339 00)
Personnel Required
Hydraulic pump drive removed (WP 0232 00)
Two
0329 00-1
TM 5-3805-261-23-2
HYDRAULIC PUMP ASSEMBLY AND MOUNTING REPLACEMENT - CONTINUED
0329 00
REMOVAL
1.
Remove four bolts (8), washers (7), and two flange halves (6) from hydraulic pump assembly (4).
CAUTION
NOTE
2.
Remove hose assembly (9) from hydraulic pump assembly (4).
3.
4.
Disconnect hose assemblies (10 and 11) from front of hydraulic pump assembly (4).
5.
Remove hose assembly (12) from elbow (13) of combination valve (2).
6.
Disconnect hose assembly (3) from top of hydraulic pump assembly (4).
13
12
6
3
5
9
12
10
397-1472
11
0329 00-2
TM 5-3805-261-23-2
0329 00
REMOVAL - CONTINUED
7.
Remove four bolts (23) and washers (22) from mounting bracket (24).
8.
Disconnect hose assemblies (14 and 15) from tee (16).
9.
Remove tee (16).
10.
Remove four bolts (19), clip (18), flange (17), tube

assembly (21), and preformed packing (20). Discard
preformed packing.
24
23
22
21
14
20
16
15
17
19
11.
18
397-1473
Position hydraulic pump assembly (4) on left side of pivot area. Slide pump and mounting bracket (24) as an assembly
from underneath cab into a position where sling can be attached.
WARNING
NOTE
Hydraulic pump assembly weighs 159 lb (72 kg).
12.
Attach sling to pump (4) and mounting bracket (24) as

an assembly and take up slack.
13.
Remove pump (4) and mounting bracket (24) as an

assembly from machine.
14.
Place pump (4) on wood blocks.
24
397-1474
0329 00-3
TM 5-3805-261-23-2
0329 00
REMOVAL - CONTINUED
15.
Remove two nuts (32), screws (30), and washers (31).
16.
Separate and remove hydraulic pump assembly (4)

from mounting bracket (24).
17.
Remove sling from hydraulic pump assembly (4).
18.
Remove four mounts (29) from mounting bracket

(24).
19.
Remove connector (28) and preformed packing (27)

from hydraulic pump assembly (4). Discard preformed
packing.
20.
Remove connector (25) and preformed packing (26).

25
26
27
32
31
28
30
29
24
397-1475
21.
Remove elbow (33) from combination valve (2).
22.
Remove elbow (34) and preformed packing (35) from

hydraulic pump assembly (4). Discard preformed
packing.
23.
Remove connector (36) and preformed packing (37).

33
33
34
35
37
36
0329 00-4
397-1476
TM 5-3805-261-23-2
0329 00

INSTALLATION
1.
Install new preformed packing (37) and connector (36) on hydraulic pump assembly (4).
2.
3.
Install elbow (33) on combination valve (2).
4.
5.
6.
Install four mounts (29) on mounting bracket (24).
7.
Position mounting bracket (24) on machine so hydraulic pump assembly (4) can be slid into mounting position.
WARNING
NOTE
Hydraulic pump assembly weighs 159 lb
(72 kg).
8.
Use sling to position hydraulic pump assembly (4) on

mounting bracket (24).
9.
Install two washers (31), screws (30), and nuts (32).
10.
Position pump (4) and mounting bracket (24) over

mounting holes.
11.
Remove sling.
24
397-1474
0329 00-5
TM 5-3805-261-23-2
0329 00
12.
Install new preformed packing (20), tube assembly

(21), flange (17), clip (18), and four bolts (19).
13.
Install tee (16).
14.
Connect hose assemblies (15 and 14) to tee (16).
15.
Install four washers (22) and bolts (23) on mounting

bracket (24). Tighten bolts to 34 lb-ft (46 Nm).
24
23
22
14
20
21
16
15
17
18
19
16.
17.
18.
19.
Connect hose assembly (3) to top of hydraulic pump assembly (4).

Install hose assembly (12) on elbow (13) of combination valve (2).
Connect hose assemblies (11 and 10) to front of hydraulic pump assembly (4).
Install new preformed packing (5), hose assembly (9), two flange halves (6), four washers (7), and bolts (8) on left side
of hydraulic pump assembly (4).
13
12
6
3
5
9
12
10
397-1472
11
20.
21.
22.
397-1473
Install hydraulic pump drive (WP 0232 00).

Install hydraulic tank (WP 0339 00).
Remove pivot locking pin (TM 5-3805-261-10) and straighten machine.
END OF WORK PACKAGE

0329 00-6
TM 5-3805-261-23-2
HYDRAULIC PUMP ASSEMBLY REPAIR
0330 00

Disassembly, Cleaning and Inspection, Assembly, Break-In
INITIAL SETUP
Maintenance Level
Ball (2)
Direct Support
Diaphragm

0348 00)
Gasket (2)
Lockwasher (19)
Ring, retaining (13)
Block (Item 13, WP 0348 00)

Maintenance fixture, automotive (Item 43, WP
0348 00)
Seal (3)
Spring (2)
References
Plate, protective (Item 52, WP 0348 00)
WP 0216 00
Rod, guide (2) (Item 69, WP 0348 00)

Materials/Parts
Adhesive (Item 4, WP 0349 00)
Cloth, emery (Item 9, WP 0349 00)

Engine off (TM 5-3805-261-10)

Sealing compound (Item 38, WP 0349 00)
Hydraulic pump assembly removed (WP 0329 00)
0330 00-1
TM 5-3805-261-23-2
HYDRAULIC PUMP ASSEMBLY REPAIR - CONTINUED
0330 00
DISASSEMBLY
1.
Remove two bolts (5), lockwashers (4), and hydraulic

rotary pump (3) from head (2) of hydraulic axial pump
(1). Discard lockwashers.
1
2
3
4
397-1478
2.
Remove preformed packing (9) and coupling (10).

3.
Matchmark back plate (8), body (7), and front plate

(6) to aid in assembly.
10
397-1479
9
CAUTION
Do not pry pump sections apart. Do not lay machined surfaces on unprotected surfaces. Scratches or grooves
will cause destruction of part.
NOTE
Tag bolts before removing to aid in installation.
4.
Remove four bolts (11), two bolts (12), and bolts (13)
from back plate (8).
8
11
12
13
0330 00-2
397-1480
TM 5-3805-261-23-2
0330 00
5.
Separate back plate (8), body (7), and front plate (6).
7
8
397-1481
6.
Remove and discard preformed packing (14) from

back plate (8).
14
8
7.
Remove drive gear (17), idler gear (15), and two dowels (16) from body (7).
397-1482
15
17
16
397-1483
8.
Remove and discard diaphragm (18) from front plate

(6).
6
18
397-1484
0330 00-3
TM 5-3805-261-23-2
0330 00
9.
Remove and discard two springs (23) and balls (24).
10.
Remove and discard gaskets (22 and 21) and seal (20).
11.
Remove seal (19) from front plate (6). Discard seal.
19
6
20
21
24
23
22
12.
397-1485
Remove bolt (28), two bolts (27), lockwashers (26),

and housing (25) from head (2). Discard lockwashers.
25
26
27
13.
14.
Remove and discard preformed packings (29, 34, and

35) from housing (25).
Remove plug (31), preformed packing (30), plug (32),
and preformed packing (33). Discard preformed packings.
28
397-1486
25
29
30
35
31
34
33
32
0330 00-4
397-1487
TM 5-3805-261-23-2
0330 00
15.
Remove two bolts (40), cover (39), piston (38), spacer

(37), and preformed packings (36 and 41) from housing (25). Discard preformed packings.
36
37
38
25
39
41
40
16.
17.
Remove plug (46), preformed packing (47), spacer

(48), piston (45), retainer (44), spring (43), and two
shims (42) from housing (25). Discard preformed
packing.
397-1488
25
50
42
49
43
44
48
45
47
46
397-1489
0330 00-5
TM 5-3805-261-23-2
0330 00
18.
Remove spring (51), three washers (52), seat (53),

spring (54), and spacer (55) from head (2).
55
54
53
19.
Remove two bolts (58), lockwashers (59), cover (60),

and preformed packing (61). Discard lockwashers and
preformed packing.
20.
Remove bolt (57) and lockwasher (56) from head (2).

Discard lockwasher.
52
51
397-1490
56
57
59
2
61
58
397-1491
60
21.
Install hydraulic axial pump (1) in fixture.
22.
Install two guide rods into head (2) and body (62).
23.
Remove three bolts (64), lockwashers (63), two bolts

(66), and lockwashers (65). Discard lockwashers.
24.
Separate head (2) from body (62) by sliding head over

guide rods.
25.
Remove two guide rods.
1,62
63
64
65 66
GUIDE RODS
FIXTURE
0330 00-6
397-1492
TM 5-3805-261-23-2
0330 00
26.
Remove and discard gasket (70).
27.
Remove plate (67) from head (2).
NOTE
Tag cartridge assemblies before removing to aid in installation.
28.
Remove cartridge assemblies (68 and 69) from head (2).
67
68
70
69
397-1493
29.
Remove piston assemblies (71 and 75) from cartridge

assembly (68).
30.
Remove retaining ring (73), insert (74), and piston

(72). Discard retaining ring.
31.
Remove valve assembly (75) from cartridge (68).
71
72
73
74
75
68
397-1494
0330 00-7
TM 5-3805-261-23-2
0330 00
32.
Remove retaining ring (81), spacer (80), ring (76), and stop (77). Discard retaining ring.
33.
Remove spool (79) from sleeve (78).
76
77
78
81
80
79
397-1495
34.
Remove setscrew (82) from cartridge (68).
68
397-1496
82
35.
Remove piston (88) from cartridge (69).
36.
Remove plug (85).
37.
Remove preformed packing (84). Discard preformed

packing.
38.
Remove spring (83) and pistons (86 and 87) from cartridge (69).
88
83
69
84
85
87
86
397-1497
0330 00-8
TM 5-3805-261-23-2
0330 00
89
39.
Remove two pins (91) from head (2).
40.
Remove four retaining rings (89), preformed packings

(90), three rings (93), and preformed packings (92).
Discard preformed packings and retaining rings.
90
93
91
92
397-1498
41.
Remove bearing cup (99) from head (2).
42.
Remove three plugs (98), preformed packings (97),

five plugs (95), and preformed packings (96) from
head (2). Discard preformed packings.
43.
Remove two dowels (94) from head (2).
95
94
96
2
99
98
97
397-1499
CAUTION
Protective plate must be used to prevent damage to the highly finished face of barrel when removing bearing.
44.
Use protective plate and puller to remove bearing

(101) from shaft (100) of body (62).
45.
Remove body (62) from fixture and install on block.
62
100
101
397-1500
0330 00-9
TM 5-3805-261-23-2
0330 00
WARNING
Do not remove second ring. Large spring in center of barrel is under compression and release of spring by
removal of second ring may cause injury to personnel.
46.
102
Remove retaining ring (102) from shaft (100). Discard

retaining ring.
100
397-1501
NOTE
Perform steps 47 and 48 at each side of body.
Shims must be kept with the cover they were removed with.
47.
Remove four bolts (108), lockwashers (109), cover (107), shims (105 and 106), and preformed packing (104) from body
(62). Discard lockwashers and preformed packings.
48.
Remove bearing (103).
103 104
105
106
107
62
109
108
397-1502
0330 00-10
TM 5-3805-261-23-2
0330 00
NOTE
Tag bolts before removing to aid in assembly.
49.
Remove nut (119), bolt (118), preformed packing

(117), nut (110), bolt (111), and preformed packing
(112) from body (62). Discard preformed packings.
50.
If required, remove four screws (116) and plate (115).
51.
Remove two plugs (114) and preformed packings

(113). Discard preformed packings.
110
111
119
118
112
117
113
114
52.
62
397-1503
Separate body (62) from housing (120) assembly.
62
120
397-1504
53.
Remove and discard retaining ring (123).
54.
Remove and discard seal (122).
55.
Remove bearing cup (121) from body (62).
62
123
122
121
397-1505
0330 00-11
TM 5-3805-261-23-2
0330 00
56.
Remove shaft (100) from housing (120).
100
120
397-1506
57.
Remove woodruff key and bearing (124) from shaft

(100).
124
WOODRUFF
KEY
100
397-1507
CAUTION
Use extreme caution not to damage the highly machined surfaces of pistons or barrel. Scratches or gouges in
the surfaces will destroy parts.
NOTE
Tag pistons before removing to aid in assembly.
0330 00-12
TM 5-3805-261-23-2
0330 00
58.
Remove housing (120) from barrel (125).
120
125
397-1508
59.
60.
120
Remove four lockbolts (130), washers (131), two

bearing plates (128), shims (132 and 133), and spacer
plate (127).
126
Remove nine pistons (129), plate (126), dowel (134),

two stops (135), and bearing cups (136) from housing
(120).
127
128
136
135
134
133
132
131
130 129
397-1509
WARNING
Spring is under extreme pressure and care must be used when removing. Use an arbor press and proper
diameter driver to compress spring.
61.
Place protective plate over barrel (125) and remove

retaining ring (140), spacer ring (139), spring (138),
and spacer ring (137). Discard retaining ring.
140
139
138
137
125
397-1510
0330 00-13
TM 5-3805-261-23-2
0330 00
62.
Remove nine bearings (141) from barrel (125).
141
125
397-1511

1.
Inspect plate (67). Use touch lapping procedure if polished in the seal band area, minor erosion, or
scratches. Use emery cloth and cleaning compound for
touch lapping. Replace if cracked, broken, erosion
across seal bands, deep scratches in seal bands or
ports, or scratches that can be felt in the seal band area
or thrust faces with fingernail or pencil.
2.
Clean and inspect all other parts in accordance with

WP 0020 00.
SEAL BANDS
67
397-1512
THRUST FACES
ASSEMBLY
120
1.
Apply thin coat of clean oil on all parts.
2.
Install dowel (134) on housing (120).
3.
Lower temperature of two bearing cups (136) and

press bearing cups into housing (120).
4.
Install two stops (135).
5.
Install spacer plate (126) into housing (120) with hole

in plate in alignment with dowel (134).
126
136
0330 00-14
135
134
397-1513
TM 5-3805-261-23-2
0330 00
6.
7.
Install new preformed packing (117), bolt (118), and

nut (119) in body (62). Bolt is the maximum stop bolt
and must be installed in the same hole from which it
was removed. Do not tighten nut.
119
Install new preformed packing (112), bolt (111), and

nut (110). Bolt is the minimum stop bolt and must be
installed in the same hole from which it was removed.
Do not tighten nut.
117
110
111
118
112
62
397-2505
NOTE
Perform steps 8 through 13 to adjust two stop bolts that will control pump output.
8.
Turn pump housing (62) over so that two adjustment bolts (111 and 118) are at bottom.
9.
Ensure nuts (110 and 119) are loosened and all gasket material is removed from top surface of body (62).
10.
Use depth gauge set to a dimension of 5.381 in. (13.67 cm) to adjust maximum angle stop bolt (118) until gauge is flush
with top surface of body (62) and end of stop bolt.
11.
Hold stop bolt (118) and tighten nut (119) to 125 lb-ft (169 Nm).
12.
Use depth gauge set to a dimension of 6.140 in. (15.60 cm) to adjust minimum angle stop bolt (111) until gauge is flush
with top surface of body (62) and end of stop bolt.
13.
Hold stop bolt (111) and tighten nut (110) to 125 lb-ft (169 Nm).
14.
Position pump housing (120) into body (62).
62
120
397-2218
0330 00-15
TM 5-3805-261-23-2
0330 00
15.
Install two bearings (103) in oil on two covers (107).
16.
Install one of two new preformed packings (104) and enough shims (105 and 106) to obtain a shim thickness of 0.015 in.
(0.38 mm) on one of two covers (107).
17.
Position one cover (107) on body (62).
18.
Install four of eight lockwashers (109) and bolts (108).

Tighten bolts to 32 lb-ft (43 Nm).
120
19.
Position second cover (107) on opposite side of body

(62) with shim(s) (105 and 106).
20.
Install remaining four of eight lockwashers (109) and

bolts (108). Tighten bolts evenly in a clockwise direction to 40 lb-in. (4.5 Nm) in steps of 10 lb-in (1.1 Nm).
Move pump housing (120) back and forth while tightening bolts.
109
108
103 104
105 106 107
107 103
62
21.
22.
Use feeler gauge to measure gap between body (62)

and cover (107) without shims. Measure at four bolt
(108) locations. Note the average thickness and add
0.008 in (0.02 mm). This will be the total shim thickness to be added to cover without shims. If the thickness of shims required is less than 0.005 in. (0.13 mm)
and more than 0.025 in. (0.64 mm), add thickness of
the shims required from feeler gauge measurement
plus 0.008 in. (0.02 mm) to the 0.015 in. (0.38 mm)
shim thickness of the other cover. Divide the total
thickness of the shims evenly and install the same
thickness of shims on each cover.
109 108
397-1515
FEELER
GAUGE
108
107
62
397-1516
108 109
Remove four bolts (108), lockwashers (109), and

cover (107) without shims.
107
397-1517
0330 00-16
TM 5-3805-261-23-2
0330 00
NOTE
Thickness of one shim is 0.00473 in. (0.1201 mm) and thickness of other shim is 0.00197 in. (0.0500 mm).
23.
Position shims (105 and 106) on cover (107) at thickness determined in step 21.
24.
Install remaining new preformed packing (104), cover

(107), four new lockwashers (109), and bolts (108).
Tighten bolts to 32 lb-ft (43 Nm). Pump housing (120)
must move freely after four bolts are tightened.
120
108 109
NOTE
Shims must be installed with the cover
they were removed with.
25.
26.
Remove eight bolts (108), washers (109), two covers

(107), and shims (105 and 106).
Remove pump housing (120) assembly.
107
104
106 105
397-1518
27.
28.
120
Install nine pistons (129), plate (127), shim(s) (132

and 133), two bearing plates (128), four washers
(131), and lockbolts (130) in pump housing (120).
Tighten lockbolts to 100 lb-in. (11 Nm).
126
Use feeler gauge to measure clearance between plate

(126) and nine pistons (129). Add or remove shim(s)
(133 and 132) until a clearance of 0.003 in. (0.08 mm)
is obtained.
128
136
29.
Install nine bearings (141) in barrel (125).
127
135
134
133
132
131
130 129
397-1509
141
125
397-1524
0330 00-17
TM 5-3805-261-23-2
0330 00
30.
Use protective plate and arbor press to install spacer

(137), spring (138), spacer (139), and new retaining
ring (140) on barrel (125).
140
139
138
137
125
397-1525
31.
Position barrel (125) assembly on block.
32.
Install pump housing (120) to barrel (125) assembly.
120
125
397-1508
33.
Install woodruff key and bearing (124) in oil on shaft

(100).
124
WOODRUFF
KEY
100
397-1507
0330 00-18
TM 5-3805-261-23-2
0330 00
34.
Install new seal (122) and new retaining ring (123) in

body (62).
35.
Lower temperature of bearing cup (121) and press

bearing cup into body (62).
62
123
122
121
397-1505
36.
Install shaft (100) into housing assembly (120).
100
120
397-1506
37.
Position housing (120) on block.
38.
Position body (62) onto housing (120).
62
120
397-1504
0330 00-19
TM 5-3805-261-23-2
0330 00
39.
Remove block and push housing (120) into body (62).
120
62
397-1526
40.
Install two new preformed packings (113) and two

plugs (114).
41.
If removed, install plate (115) with four screws (116).
42.
Lubricate two new preformed packings (104) with

clean hydraulic oil.
43.
Install two new preformed packings (104), correct

amount of shims (105 and 106), two covers (107),
eight new lockwashers (109), and bolts (108).
114
113
109
107
106 105
104
108
116
44.
115
397-1527
Install new retaining ring (102) on shaft (100).
102
100
397-1501
0330 00-20
TM 5-3805-261-23-2
0330 00
45.
Install bearing (101) on shaft (100) using protective

plate and puller.
100
101
397-1500
46.
Install two dowels (94) in head (2).
47.
Install five new preformed packings (96), plugs (95),

three new preformed packings (97), and plugs (98).
48.
Lower temperature of bearing cup (99) and install in

head (2).
94
95
96
2
99
98
97
49.
50.
397-1499
89
Install three new preformed packings (92), new retaining rings (93), four new preformed packings (90), and
new retaining rings (89) in head (2).
90
Install two pins (91).
93
91
92
397-1498
0330 00-21
TM 5-3805-261-23-2
0330 00
51.
Install pistons (86 and 87) and spring (83) in cartridge

(69).
52.
53.
Install piston (88).
88
69
83
84
87
85
86
397-1497
54.
Apply sealing compound to setscrew (82) and install

in cartridge (68).
68
82
55.
Install spool (79) in sleeve (78).
56.
Install stop (77), ring (76), spacer (80), and new

retaining ring (81).
76
397-1496
77
78
81
80
79
397-1495
0330 00-22
TM 5-3805-261-23-2
0330 00
71
57.
Install piston assembly (75) in cartridge (68).
58.
Install insert (74) and new retaining ring (73) in cartridge (68).
59.
72
73
Install pistons (71 and 72) in cartridge (68).
74
75
68
397-1494
60.
Install cartridge assemblies (68 and 69) in head (2).
61.
Install plate (67) and new gasket (70).
67
68
70
69
0330 00-23
397-1493
TM 5-3805-261-23-2
0330 00
62.
Install two guide rods in body (62).
63.
Position head (2) on guide rods.
64.
Install two lockwashers (65), bolts (66), three new

lockwashers (63), and bolts (64).
65.
Remove two guide rods.
1,62
63
64
65 66
GUIDE RODS
FIXTURE
66.
Install new lockwasher (56) and bolt (57).
67.
Install new preformed packing (61), cover (60), two

new lockwashers (59), and bolts (58).
397-1492
56
57
59
2
61
397-1491
60
68.
58
Install spacer (55), spring (54), seat (53), three washers (52), and spring (51) in head (2).
51
2
0330 00-24
55
54
53
52
397-1490
TM 5-3805-261-23-2
0330 00
69.

housing (25).
70.
Install two shims (42), spring (43), retainer (44), piston (45), spacer (48), new preformed packing (47),
and plug (46) into housing (25).
25
50
49
42
43
44
45
48
47
46
397-1489
71.
Install new preformed packings (36 and 41), spacer

(37), piston (38), cover (39), and two bolts (40) in
housing (25).
36
37
38
25
41
40
0330 00-25
39
397-1488
TM 5-3805-261-23-2
0330 00
72.
Install new preformed packing (33), plug (32), new

preformed packing (30), and plug (31) in housing
(25).
73.
Install new preformed packings (29, 34, and 35).
25
29
30 31
35
34
74.
33
32
397-1487
Install housing (25) assembly, two new lockwashers

(26), bolts (27), and bolt (28) on head (2).
25
26
27
2
28
75.
Install new seal (19) on front plate (6).
76.
Install new seal (20) and new gaskets (21 and 22).
77.
Install two new balls (24) and new springs (23).
19
397-1486
6
20
21
24
23
22
0330 00-26
397-1485
TM 5-3805-261-23-2
0330 00
78.
Install new diaphragm (18) on front plate (6).
6
18
397-1484
79.
Install two dowels (16), idler gear (15), and drive gear
(17) in body (7).
15
17
16
397-1483
80.
Install new preformed packing (14) on back plate (8).
14
8
81.
Position front plate (6), body (7), and back plate (8).
397-1482
6
7
8
397-1481
0330 00-27
TM 5-3805-261-23-2
0330 00
82.
Install two bolts (13), bolts (12), and four bolts (11) on
backplate (8).
11
12
13
83.
397-1480
Install coupling (10) and new preformed packing (9).
10
9
84.
Install hydraulic rotary pump (3) on head (2) of

hydraulic axial pump (1) with two new lockwashers
(4) and bolts (5).
397-1479
1
2
3
4
397-1478
85.
Fill pump half full with hydraulic oil (WP 0216 00).
Turn pump shaft (100) with a torque wrench. Not
more than 120 lb-in. (14 Nm) must be used to start
shaft turning and 84 lb-in. (10 Nm) should be needed
to keep pump turning. If torque required exceeds these
specifications, pump must be disassembled to locate
the problem.
100
397-1526
86.
Install hydraulic pump assembly (WP 0329 00).
0330 00-28
TM 5-3805-261-23-2
0330 00
BREAK-IN
CAUTION
Ensure that hydraulic tank has been filled.
Cap of hydraulic tank must be loosened.
1.
Slightly loosen, but not remove, discharge hose of hydraulic pump (WP 0329 00).
2.
With machine throttle in OFF position, prime hydraulic pump by cranking engine (TM 5-3805-261-10) until oil seeps
from loosened discharge connection.
3.
Fully tighten discharge hose and hydraulic tank cap.
4.
Disengage unloader valve and start engine (TM 5-3805-261-10). Run engine at low idle until hydraulic oil system is
warmed to approximately 125F (52C).
5.
With engine remaining at low idle, carefully release unloader valve and operate blade up and down (TM 5-3805-261-10)
for approximately 10 minutes. Take care not to reach end of cylinder travel.
6.
Increase engine speed to approximately 1,500 RPM and operate circle drive back and forth (TM 5-3805-261-10) for
approximately 15 minutes. Stop engine.
7.
Check hydraulic oil level and fill as necessary (WP 0216 00).
END OF WORK PACKAGE
0330 00-29/(-30 Blank)
TM 5-3805-261-23-2
CIRCLE DRIVE MOTOR REPAIR
0331 00

INITIAL SETUP
References
Maintenance Level
WP 0020 00
Direct Support

0348 00)

Materials/Parts
Engine off (TM 5-3805-261-10)

Ring, retaining
Seals (2)
Circle drive motor removed (WP 0217 00)
0331 00-1
TM 5-3805-261-23-2
CIRCLE DRIVE MOTOR REPAIR - CONTINUED
0331 00
DISASSEMBLY
CAUTION
Use care to prevent damage to housing.
1.
2.
Remove seven screws (1), cover (2), and preformed

packing (3) from circle drive motor. Discard preformed packing.
1
2
Remove commutator inner plate (4) and outer plate (5)

from sleeve (6).
3
4
5
6
397-1528
3.
4.
Remove manifold (8) and spacer plate (9).
5.
Remove inner rotor (10), seven pins (11), and outer

rotor (12) as an assembly.
6.
Remove spacer plate (13).
7.
Remove bearing (17) and shaft (16).
8.
Remove sleeve (6) and coupling (15) from housing

(14).
17
16
7
8
15
9
10
11
12
13
14
397-1529
0331 00-2
TM 5-3805-261-23-2
0331 00
9.
Remove seal (22) from housing (14). Discard seal.
10.
Remove retaining ring (21). Discard retaining ring.
11.
Remove spacer ring (20), shim (18), and seal (19).

Discard seal.
22
21
20
18
19
14
397-1530
12.
Remove bearing (23) and preformed packing (24)

from housing (14). Discard preformed packing.
23
24
14
13.
Use arbor press to remove bearing (26), two bearing

seats (25), and bearing (27) from housing (14).
397-1531
14
27
25
26
397-1532

0331 00-3
TM 5-3805-261-23-2
0331 00
ASSEMBLY
1.
Install two bearing seats (25) and bearing (27) in housing (14).
2.
Install bearing (26) in housing (14). Set to depth of

2.41 in. (61.2 cm) below surface noted.
3.
4.
Install bearing (23) in housing (14). Set to depth of

0.10 in. (2.5 mm) below surface noted.
23
24
26
25
27
SURFACE
14
397-1533
5.
Install new seal (19), shim (18), and spacer (20) in

housing (14).
6.
Install new retaining ring (21).
7.
Install new seal (22).
22
21
20
18
19
14
397-1530
0331 00-4
TM 5-3805-261-23-2
0331 00
8.
Install coupling (15) and sleeve (6) on housing (14).
9.
Install shaft (16) and bearing (17).
10.
Install plate (13).
11.
Install outer rotor (12), seven pins (11), and inner rotor
(10) as an assembly.
12.
Install plate (9) and manifold (8).
13.
17
16
7
8
15
9
10
11
12
13
14
397-1529
14.
Install commutator outer plate (5) and inner plate (4)

into sleeve (6).
15.
Install new preformed packing (3) and cover (2) with

seven screws (1). Tighten screws to 50 lb-ft (68 Nm).
1
2
3
4
5
6
397-1528
16.
Install circle drive motor (WP 0217 00).
END OF WORK PACKAGE

0331 00-5/(-6 Blank)
TM 5-3805-261-23-2
HYDRAULIC CONTROL VALVES REPAIR
0332 00

INITIAL SETUP
Maintenance Level
Personnel Required
Two
Direct Support
References

WP 0020 00

0348 00)
WP 0216 00
Materials/Parts
Lockwasher (3)
Engine off (TM 5-2805-261-10)

Seal (41)
8/32-2B screw
Hydraulic control valves removed (WP 0249 00)
0332 00-1
TM 5-3805-261-23-2
HYDRAULIC CONTROL VALVES REPAIR - CONTINUED
0332 00
DISASSEMBLY
NOTE
Perform the following steps to disassemble the left or right side control valve assembly. The left control
valve assembly is shown.
1.

2.

1
2
3
5
4
397-1546
NOTE
Control valve assembly must be matchmarked if entire control valve is disassembled to ensure proper placement of each valve in assembly.
3.
Matchmark housings (1 and 6) and valves (8).
4.
Remove three bolts (12) and lockwashers (13). Discard lockwashers.
0332 00-2
TM 5-3805-261-23-2
0332 00
CAUTION
Do not place machined surfaces of manifolds or valves on unprotected surface. Scratches or nicks will permit valve leakage.
5.
Separate housings (1 and 6) and valve (8) assemblies.
6.
At each separation surface, remove and discard two preformed packings (7), seal (9), and preformed packings
(10 and 11).
7
8
11
9
10
9
10
11
7
1
12
11
10
0332 00-3
13
397-1547
TM 5-3805-261-23-2
0332 00
7.
8.
15
Remove two bolts (15), washers (14), and lever (16)

assembly from valve (8) assembly.
14
17
16
397-1548
9.
Remove boot (21).
10.
Remove nut (22) and ring (23).
11.
Remove two bearings (18), preformed packing (19),

seal (20), and lever (16) from plate (24). Discard preformed packing.
16
18
19
20
18
24
23 22
21
397-1549
0332 00-4
TM 5-3805-261-23-2
0332 00
12.
Remove two screws (25) and lock (29) from valve (8).
WARNING
Spring is under pressure. Loosen plug carefully to relieve pressure of spring. Failure to follow this warning
13.
14.
Remove valve (26) assembly from valve (8) assembly.
25
29
28
27
26
397-1550
0332 00-5
TM 5-3805-261-23-2
0332 00
27
15.
16.
Remove two retainers (28).
17.
Remove spring (27) and two bushings (29 and 30)

from valve (26).
28
29
28
30
26
397-1551
18.
Remove two plugs (34) and preformed packings (31) from valve (8) assembly. Discard preformed packings.
WARNING
19.
31
34
33
32
0332 00-6
397-1552
TM 5-3805-261-23-2
0332 00
20.
Remove spring (36) and ball (37) from valve (8) assembly.
21.
Use 3/8 in. hex key to remove seat (38) and remove preformed packing (39). Discard preformed packing.
WARNING
CAUTION
Do not allow shim(s) and washers to fall from plug.
22.
Remove plug (35) assembly from valve (8) assembly.
39
38
37
35
36
397-1554
0332 00-7
TM 5-3805-261-23-2
0332 00
CAUTION
Keep shims and washers together as removed.
23.
40
Remove shim(s) (40), washer(s) (41), spring (43), and

preformed packing (42) from plug (35). Discard preformed packing.
41
42
43
35
397-1555
24.
25.
Remove four bolts (48 and 49) and cover (50) from
valve (8).
26.
Remove and discard two preformed packings (51) and

preformed packing (45).
27.
Remove valve (52).
28.
Use 8/32-2B screw and puller to remove sleeve (44)

assembly.
44
45
52
46
51
47
50
0332 00-8
49
48
397-1556
TM 5-3805-261-23-2
0332 00
29.
Remove and discard two preformed packings (53)

from sleeve assembly (44).
53
44
53
397-1557

Clean all parts in accordance with WP 0020 00.
ASSEMBLY
1.
Install two new preformed packings (53) on sleeve assembly (44).
2.
Apply thin coat of clean oil to two preformed packings (53).
3.
Install sleeve (44) assembly in valve (8).
4.
Install valve (52) in valve (8) assembly.
5.
Install new preformed packing (45) and two new preformed packings (51) in cover (50).
6.
Install cover (50) to valve (8) with four bolts (48 and 49).
7.
Valve (105) Assembly
Quantity of Shims (40)
Quantity of Washers (41)
Scarifier
Blade life, R.H.
Wheel lean
Centershift
Articulation
Blade tip
Circle drive
Sideshift
Blade lift, L.H.
0332 00-9
TM 5-3805-261-23-2
0332 00
8.
40
Install new preformed packing (42), spring (43),

washers (41), and shim(s) (40) on plug (35). Install
correct quantities of shim(s) and washers. Refer to
chart above.
41
42
43
35
397-1555
9.
Install plug (35) assembly in valve (8) assembly.

Tighten to 35 lb-ft (47 Nm).
35
397-1558
10.
Install new preformed packing (39) on valve seat (38).
38
39
397-1559
0332 00-10
TM 5-3805-261-23-2
0332 00
11.
12.
Lubricate outer diameter of preformed packing (39)

lightly with clean oil. Screen in seat must be clean
before installing.
Install valve seat (38) in valve (8) assembly. Tighten to

10 to 16 lb-ft (14 to 21 Nm).
38
397-1560
13.
Install ball (37), spring (36), and plug (33) in valve (8)
assembly.
14.
Install two new preformed packings (31) and plugs

(34).
31
34
33
36
0332 00-11
37
397-1562
TM 5-3805-261-23-2
0332 00
15.
Install two bushings (29 and 30) and spring (27) on

valve (26).
16.
17.
Install two retainers (28).
18.
Release spring (27).
27
28
29
28
30
26
397-1551
19.
Install valve assembly (26) in valve (8) assembly

while aligning hole in valve with hole for lever assembly.
20.
Loosely install new preformed packing (27) and plug

(28).
28
27
26
397-1563
0332 00-12
TM 5-3805-261-23-2
0332 00
21.
20
Install new preformed packing (19) on seal (20).
19
397-1565
22.
Position seal (20) and two bearings (18) on lever (16).
18
16
20
18
397-1566
23.
Position lever (16) assembly into plate (24).
24.
Loosely install ring (23) and nut (22).
22
16
23
24
397-1567
0332 00-13
TM 5-3805-261-23-2
0332 00
25.
Install new preformed packing (17) to lever (16) assembly.
26.
Position lever (16) assembly to valve (8) assembly.

Insert end of lever in hole valve (26).
27.
15
14
16
NOTE
28.
Perform steps 28 through 30 to adjust

end play of valve.
While moving lever (16) back and

forth slightly, tighten plug just until
there is no play. Do not overtighten
plug.
28
26
17
8
Tighten plug (28) to remove end play of valve (26).
397-1568
29.
With nut (22) loosened, rotate ring (23) until it contacts bearing (18), then turn to left 45 degrees to obtain
lever (16) end play of 0.006 in. (0.15 mm) using dial
indicator.
30.
Hold ring (23) and tighten nut (22) to 25 lb-ft (34

Nm).
END PLAY
0.006 IN. (0.15 MM)
16
22
23
18
397-1564
0332 00-14
TM 5-3805-261-23-2
0332 00
25
31.
Install lock (29) with two screws (25).
32.
Install boot (21).
29
21
397-1569
NOTE
Perform the following steps to assemble the left or right side control valve assembly. The left control valve
assembly is shown.
33.
At each surface to be joined, install new preformed packing (11 and 10), seal (9), and two new preformed packings (7).
34.
Position valve (8) assemblies and manifolds (1 and 6) as matchmarked.
35.
Install three new lockwashers (13) and bolts (12).
7
8
11
9
10
9
10
11
7
1
12
11
10
13
0332 00-15
397-1547
TM 5-3805-261-23-2
0332 00
36.

manifold (6).
37.

manifold (1).
38.
Install hydraulic control valves (WP 0249 00).
1
2
3
5
4
397-1546
END OF WORK PACKAGE
0332 00-16
TM 5-3805-261-23-2
CENTERSHIFT CYLINDER REPAIR
0333 00

INITIAL SETUP
Personnel Required
Maintenance Level
Direct Support
Two
References
WP 0020 00

0348 00)
WP 0216 00
Materials/Parts

Packing, preformed
Engine off (TM 5-3805-261-10)
Seal (3)
Seal assembly (4)
Washers, lock (4)
Centershift cylinder removed (WP 243 00)
DISASSEMBLY
1.
Loosen hub (2) from cylinder (3).
2.
Remove rod (1) assembly from cylinder (3).
397-1979
397-1979
0333 00-1
TM 5-3805-261-23-2
CENTERSHIFT CYLINDER REPAIR - CONTINUED
0333 00
3.
Remove bolt (6) and washer (5) from end of rod (1).
4.
Remove piston (4) assembly from rod (1).
397-1980
5.
Remove bushing (7) and seal assembly (8) from piston

6.
397-1981
Remove head (9) assembly from rod (1).
1
397-1982
0333 00-2
TM 5-3805-261-23-2
0333 00
7.
Remove packing retainer (11), preformed packing

(12), and seals (10, 13, and 14) from head (9). Discard
preformed packing and seals.
10
9
11
12
14
13
397-1983
8.
Remove hub (2) from rod (1).

ASSEMBLY
1.
Position hub (2) on rod (1).
397-1984
2.
Apply thin coat of clean oil to new seals (10, 13, and 14), new preformed packing (12), and packing retainer (11).
3.
Use a seal installer to install new seals (10, 13, and 14) into head (9). Lips of seals (10 and 13) is toward inside of head.
Lip of seal (14) is toward outside of head.
4.
Install packing retainer (11) and new preformed packing (12) on head (9).
5.
Install head (9) assembly on rod (1).
0333 00-3
TM 5-3805-261-23-2
0333 00
6.
Using seal expander, install new seal assembly (8) and

bushing (7) on piston (4).
7.
Install piston (4) assembly on rod (1).
8.
Apply thin coat of thread lubricant to threads of bolt

(6) and install washer (5) and bolt to end of rod (1).
Tighten bolt to 800 lb-ft (1,085 Nm).
397-1981
1
4
397-1980
9.
Apply clean oil to outside of head (9), inside of hub (2), and inside of cylinder (3).
10.
Install rod (1) assembly into cylinder (3).
NOTE
When tightening hub, ensure that rod is fully extended. This will keep cylinder, piston, and head aligned.
11.
Install hub (2) on cylinder (3). Tighten to 450 lb-ft

(610 Nm).
9
3
397-1979
397-1979
12.
Install centershift cylinder (WP 0243 00).
END OF WORK PACKAGE
0333 00-4
TM 5-3805-261-23-2
BLADE TIP CYLINDER REPAIR
0334 00

INITIAL SETUP
Maintenance Level
Seal (6)
Direct Support
Seal assembly

Tool kit, general mechanics, (Item 89, WP 0348
00)
0348 00)
00)
Personnel Required
Two
References
WP0020 00
Materials/Parts

Engine off (TM 5-3805-261-10)
Bearing (2)
Gasket
Packing, preformed
Blade tip cylinder removed (WP 0244 00)
0334 00-1
TM 5-3805-261-23-2
BLADE TIP CYLINDER REPAIR - CONTINUED
0334 00
DISASSEMBLY
CAUTION
Use care not to remove or damage bearings or rings which remain in cylinder.
1.
Remove and discard two seals (1) from cylinder (2).
2.
Remove and discard two seals (4) from rod (3).
1
2
3
3
4
397-1598
3.
Loosen sleeve (5).
4.
2
3
5
397-1985
NOTE
Inspect rings and bearings before removal

and replace only if damaged.
5.
Remove two rings (6) and bearing (7) from cylinder

(2). Discard bearing.
397-1986
0334 00-2
TM 5-3805-261-23-2
0334 00
6.
7.
9
10
397-1987
8.
11

10
12
397-1988
9.
13
397-1989
10.
Remove packing retainer (14), preformed packing

(15), seals (18 and 17), and gasket (16) from head
(13). Discard preformed packing, seals, and gasket.
14
15
13
16
17
18
397-1990
0334 00-3
TM 5-3805-261-23-2
0334 00
11.
15
Remove sleeve (15) from rod (3).
397-1991
12.
Remove two rings (19) and bearing (20) from rod (3).
Discard bearing.
20
19
397-1992

ASSEMBLY
1.
Install one ring (19) to a depth of 0.29 in. (7.4 mm) from the outer surface of rod (3).
2.
Install new bearing (20) in rod (3).
3.
Install other ring (19) next to bearing (20) to a depth of 0.29 in. (7.4 mm) from outer surface of rod (3) assembly .
4.
Position sleeve (5) on rod (3).
19
20
5
0334 00-4
397-1993
TM 5-3805-261-23-2
0334 00
5.
6.
7.
14
Apply thin coat of clean oil to packing retainer (14),

new preformed packing (15), new gasket (16), and
new seals (17 and 18).
15
13
Use a seal installer to install new gasket (16) and two

new seals (17 and 18). Lip of seal (17) is toward inside
of head (13). Lip of seal (18) is toward outside of
head.
16
17
18
Install new preformed packing (15) and packing

retainer (14) to head (13).
397-1990
8.
Install head (13) assembly on rod (3).
13
3
397-1989
9.
Use a seal expander to install new seal assembly (12)

and ring (11) on piston (10).
11
10
12
397-1988
0334 00-5
TM 5-3805-261-23-2
0334 00
10.
11.

9
10
3
397-1987
12.
If removed, install one of two rings (6) to a depth of

0.15 in. (3.8 mm) from outer surface of cylinder (2).
13.
If removed, install new bearing (7) in center of cylinder (2).
14.
If removed, install other ring (6) next to bearing (7).

Depth of ring to outer surface of cylinder (2) should be
0.15 in. (3.8 mm).
6
7
2
397-1986
NOTE
Apply thin coat of grease to outside of head assembly, inside of sleeve and inside of cylinder.
15.
Install rod cylinder (3) assembly into cylinder (2).
NOTE
Tighten sleeve with rod assembly fully extended. This will keep cylinder, piston, and head in alignment.
16.
Install sleeve (5) on cylinder (2). Tighten sleeve to 450 lb-ft (610 Nm).
2
3
5
397-1985
0334 00-6
TM 5-3805-261-23-2
0334 00
NOTE
Seals can be damaged by careless handling during installation. Driving tools must not strike bearings or
rings which remain in rod and cylinder assembly.
17.
Install two new seals (4) with lips toward outside and
even with outer surface of rod (3).
18.
Install two new seals (1) in end of cylinder (2).
1
2
3
3
4
397-1598
19.
Install blade tip cylinder (WP 0244 00).
END OF WORK PACKAGE
0334 00-7/(-8 Blank)
TM 5-3805-261-23-2
BLADE LIFT CYLINDER REPAIR
0335 00

INITIAL SETUP
Personnel Required
Maintenance Level
Direct Support
Two

0348 00)
References
WP 0020 00

Materials/Parts


Packing, preformed
Engine off (TM 5-3805-261-10)
Retainer, packing
Seal (5)
Seal assembly
Blade lift cylinder removed (WP 0245 00)
0335 00-1
TM 5-3805-261-23-2
BLADE LIFT CYLINDER REPAIR - CONTINUED
0335 00
DISASSEMBLY
NOTE
Each of these two sleeve bearings may have already been removed with caps.
1.
Use a puller to remove two sleeve bearings (1) and

seals (2). Discard seals.
2.
Use a puller to remove two sleeve bearings (3), if necessary, from cylinder (4).
1
2
3
4
3
2
1
397-1603
3.
Loosen hub (5) of cylinder (4).
4.
4
6
397-2501
0335 00-2
TM 5-3805-261-23-2
0335 00
5.
Remove bolt (7), washer (9), and piston (8) assembly

from rod (6) assembly.
7
9
8
397-1996
6.
Remove seal assembly (11) and bushing (10) from piston (8). Discard assembly.
10
8
11
397-1997
0335 00-3
TM 5-3805-261-23-2
0335 00
7.
12
397-1998
8.
Remove and discard preformed packing (13), packing

retainer (14), and seals (15, 16, and 17) from head
(12).
13
14
12
15
16
17
397-1999
0335 00-4
TM 5-3805-261-23-2
0335 00
9.
Remove hub (5) from rod (6).
397-2000

ASSEMBLY
1.
Position hub (5) on rod (6).
2.
Apply thin coat of clean oil to new seals (15, 16, and 17).
3.
Use seal installer to install seals (15, 16, and 17) in head (12). Lip on inner seal (15) and center seal (16) face inside head
(12). Lip on outside seal (17) faces outside head.
4.
Install new preformed packing (13) and new packing retainer (14) on head (12).
5.
Position head (12) assembly on rod (6).
6.
Use a seal expander to install bushing (10) and new

seal assembly (11) on piston (8).
10
8
11
397-1997
0335 00-5
TM 5-3805-261-23-2
0335 00
7.
8.

7
9
8
397-1996
9.
10.
Apply thin coat of grease to outside of head (12) and inside of hub (5).
NOTE
Tighten hub with rod assembly fully extended. This will keep cylinder, piston, and head in alignment.
11.
Install hub (5) to cylinder (4). Tighten hub to 450 lb-ft

(610 Nm).
6
12
5
397-1995
12.
Install blade lift cylinder (WP 0245 00).
END OF WORK PACKAGE

0335 00-6
TM 5-3805-261-23-2
ARTICULATION CYLINDER REPAIR
0336 00

INITIAL SETUP
Personnel Required
Maintenance Level
Direct Support
Two

0348 00)

Materials/Parts

Engine off (TM 5-3805-261-10)

Packing, preformed
Ring
Hydraulic pressure relieved (WP 0020 00)
Seal (2)
Articulation cylinder removed (WP 0246 00)
0336 00-1
TM 5-3805-261-23-2
ARTICULATION CYLINDER REPAIR - CONTINUED
0336 00
DISASSEMBLY
1.
Remove and discard four seals (2) from articulation cylinder (3) assembly.
CAUTION
Removal of bearings from cylinder can cause destruction of bearings. Remove bearings only if inspection
NOTE
Use a driver and press to remove two bearings, if necessary, from cylinder.
2.
Inspect two bearings (1). Replace if cracked, broken,

distorted, grooved, or worn.
1
2
1
2
3
397-1609
0336 00-2
TM 5-3805-261-23-2
0336 00
3.
Loosen cap (5) of cylinder (3).
4.
3
397-2368
5.
Remove bolt (8), washer (7), and piston (6) from rod (4).
6
7
8
397-2369
0336 00-3
TM 5-3805-261-23-2
0336 00
6.
Remove seal assembly (11) and bushing (9) from piston (10). Discard seal assembly.
10
11
397-2370
7.
Remove housing (12) assembly and cap (5) from rod

(4).
4
12
397-2371
8.
Remove and discard ring (13), preformed packing

(14), seal (16), and seal (15) from housing (12).
13
14
12
15
16
397-2372

0336 00-4
TM 5-3805-261-23-2
0336 00
ASSEMBLY
1.
Apply thin coat of clean oil to new seals (15 and 16), new ring (13), and new preformed packing (14).
2.
Use a seal installer to install new seals (15 and 16) into housing (12).
3.
Install preformed packing (14) and ring (13).
4.
Position cap (5) and housing (12) assembly on rod (4).
5.
Use seal expander to install ring (9) and new seal assembly (11) on piston (10).
6.
7.
Apply thin coat of thread lubricant to threads of bolt (8) and install washer (7) and bolt to end of rod (4). Tighten bolt to
800 lb-ft (1,085 Nm).
10
7
8
397-2369
0336 00-5
TM 5-3805-261-23-2
0336 00
8.
Apply thin coat of grease to outside of head (12) and

inside of cap (5).
4
12
397-2371
9.
NOTE
Tighten cap with rod assembly fully extended. This will keep cylinder, piston, and housing in alignment.
10.
Install cap (5) to cylinder (3). Tighten cap to 450 lb-ft

(610 Nm).
3
397-2368
0336 00-6
TM 5-3805-261-23-2
0336 00
NOTE
Perform step 1 if bearings were removed from cylinder.
11.
Install two bearings (1) into articulation cylinder (3).
12.
Install new seals (2) in each end of cylinder (3) with

lip side facing outward.
1
2
1
2
3
397-1609
13.
Install articulation cylinder (WP 0246 00).
END OF WORK PACKAGE
0336 00-7/(-8 Blank)
TM 5-3805-261-23-2
SIDESHIFT CYLINDER REPAIR
0337 00

INITIAL SETUP
Personnel Required
Maintenance Level
Direct Support
Two
References

0348 00)
WP 0216 00
Materials/Parts

Packing, preformed
Engine off (TM 5-3805-261-10)
Ring
Seal assembly
Seal (3)
Sideshift cylinder removed (WP 0247 00)
0337 00-1
TM 5-3805-261-23-2
SIDESHIFT CYLINDER REPAIR - CONTINUED
0337 00
DISASSEMBLY
1.
Loosen cap (3) of side shift cylinder (1) assembly.
2.
2
3
3.
4.
397-2001
2
5
6
7
397-2002
0337 00-2
TM 5-3805-261-23-2
0337 00
5.

8
7
397-2003
6.
Remove housing (10) assembly from rod (2).
10
397-2004
7.
Remove ring (11), preformed packing (12), and seals

(13, 14, and 15) from housing (10). Discard preformed
packing and seals.
10
15
13
14
11
12
397-2005
0337 00-3
TM 5-3805-261-23-2
0337 00
8.
Remove cap (3) from rod (2).

ASSEMBLY
1.
Position cap (3) on rod (2).
397-2006
2.
Apply thin coat of clean oil to new seals (13, 14, and
15), new preformed packing (12), and ring (11).
3.
Use a seal installer to install new seals (13, 14, and 15)
in housing (10). Lip of seal (14) is toward inside of
housing. Lip of seal (13) is toward outside of housing.
4.
10
15
13
14
11
Install new preformed packing (12) and ring (11) to

housing (10).
12
397-2005
5.
Install housing (10) assembly on rod (2).
6.
Use a seal expander to install new seal assembly (8)

and ring (9) on piston (7).
397-2003
7.
Install piston (7) assembly on rod assembly (2).
8.

(5) and install washer (6), and bolt to end of rod (2).
2
5
6
7
397-2002
0337 00-4
TM 5-3805-261-23-2
0337 00
9.
Apply thin coat of grease to outside of housing (10),

inside of cap (3), and inside of cylinder (1).
10
397-2004
10.
2
3
NOTE
11.
Install cap (3) on cylinder (1). Tighten cap to 450 lb-ft (610 Nm).
12.
Install sideshift cylinder (WP 0247 00).
0337 00-5/(-6 Blank)
397-2001
TM 5-3805-261-23-2
SCARIFIER CYLINDER REPAIR
0338 00

INITIAL SETUP
Maintenance Level
Packing, preformed
Direct Support
Seal (7)
Seal assembly

0348 00)
Personnel Required
Two
References
WP 0020 00
Materials/Parts


Engine off (TM 5-3805-261-10)
Scarifier cylinder removed (WP 0248 00)
0338 00-1
TM 5-3805-261-23-2
SCARIFIER CYLINDER REPAIR - CONTINUED
0338 00
DISASSEMBLY
1.
Remove and discard four seals (2) from scarifier cylinder (3) assembly.
CAUTION
Removal of bearings from cylinder can cause destruction of bearings. Remove bearings only if inspection
2.
Inspect two bearings (1). Remove if cracked, broken,

distorted, grooved, or worn.
2
1
1
3
397-1621
3.
Loosen cap (5) of scarifier cylinder (3) assembly.
4.
4
5
0338 00-2
397-2007
TM 5-3805-261-23-2
0338 00
5.
6.
6
8
397-2008
7.
Remove seal assembly (9) and ring (10) from piston

9
10
8
397-2009
8.
Remove housing (11) assembly from rod (4).
11
397-2010
0338 00-3
TM 5-3805-261-23-2
0338 00
9.
Remove and discard seals (15, 16, and 17), preformed

packing (12), and ring (13) from housing (14).
15
16
17
13
12
14
397-2011
10.
Remove cap (5) from rod (4).
4
5
397-2012

ASSEMBLY
1.
Position cap (5) on rod (4).
2.
Apply thin coat of clean oil to new seals (17, 16, and 15), new ring (13), and new preformed packing (12).
3.
Use a seal installer to install new seals (17, 16, and 15) on housing (14). Lip on center seal (16) faces inside housing. Lip
on outside seal (15) faces outside housing.
4.
Install new preformed packing (12) and new ring (13) on housing (14).
0338 00-4
TM 5-3805-261-23-2
0338 00
5.
Install housing (14) assembly on rod (4).
14
397-2010
6.
Use a seal expander to install ring (10) and new seal

assembly (9) on piston (8).
9
10
8
397-2009
7.
8.

6
8
397-2008
0338 00-5
TM 5-3805-261-23-2
0338 00
NOTE
Apply thin coat of grease to outside of
housing (14) and inside of cap (5).
9.
14
397-2010
NOTE
10.
Install cap (5) on cylinder (3) and tighten to 450 lb-ft

(610 Nm).
4
5
397-2007
NOTE
Perform step 11 if bearings were removed from cylinder.
11.
Install two bearings (1) into scarifier cylinder (3)

assembly.
12.
Install four new seals (2) in cylinder (3) with lips

toward outside. Lips must be approximately even with
outer surface cylinder.
13.
2
1
1
Install scarifier cylinder (WP 0248 00).
2
END OF WORK PACKAGE
0338 00-6
397-1621
TM 5-3805-261-23-2
HYDRAULIC TANK AND MOUNTING MAINTENANCE
0339 00

Personnel Requested
Maintenance Level
Two
Direct Support
References

0348 00)
WP 0216 00

Materials/Parts
Engine off (TM 5-3805-261-10)
Hydraulic tank drained (WP 0216 00)
Gasket
Locknut
Hydraulic tank lines and fittings removed (WWP

0250 00)
Nut (6)
Oil temperature switch removed (WP 0116 00)
Packing, preformed
Hydraulic tank filters removed (WP 0231 00)
0339 00-1
TM 5-3805-261-23-2
HYDRAULIC TANK AND MOUNTING MAINTENANCE - CONTINUED
0339 00
REMOVAL
WARNING
NOTE
Hydraulic tank weighs 250 lb (113 kg).
1.
With assistance, attach sling to hydraulic tank (1). Remove slack from sling.
NOTE
Steps 2 through 4 cover the left support and hardware. Follow these instructions for the right support and
hardware.
2.
Remove two bolts (7), washers (6), spacers (8), and brackets (9).
3.
Remove nut (5), washers (4 and 3), mount (2), washers (12 and 11), and bolt (10).
SLING
2
3
4
12
10
11
9
8
7
6
0339 00-2
397-1623
TM 5-3805-261-23-2
0339 00
REMOVAL - CONTINUED
4.
Remove nut (17), washers (18 and 19), mount (16),

washers (15 and 14), bolt (13), and support (20).
5.
Use sling to remove hydraulic tank (1) from machine

and place hydraulic tank in work area.
6.
Remove sling.
SLING
13
14
20
15
19
18
16
17
397-1624
DISASSEMBLY
1.
Remove two bolts (23), nuts (29), washers (30), and

plate (28) from hydraulic tank (1).
2.
Remove four bolts (26), washers (27), and angle

brackets (25 and 21).
3.
Remove plugs (22 and 24).
1
29
30
21
28
27
22
26
23
25
0339 00-3
24
397-1625
TM 5-3805-261-23-2
0339 00
REMOVAL - CONTINUED
4.
Remove two seat (31) assemblies from top of hydraulic tank (1).
31
1
397-1626
WARNING
Springs are under pressure. Loosen nut carefully to relieve pressure of springs. Failure to follow this warning may cause injury to personnel.
NOTE
Perform step 5 for each of two valve assemblies.
5.
Remove locknut (36), spacer (37), retainer (38), spring

(35), seat (31), valve (34), spring (39), and washer
(33) from bolt (32). Discard locknut.
35
36
37
34
38
33
31
32
39
397-1627
0339 00-4
TM 5-3805-261-23-2
0339 00
REMOVAL - CONTINUED
40
6.
Remove 48 nuts (44), washers (43), bolts (42), and

cover (41) from hydraulic tank (1). Matchmark cover
to aid in installation.
7.
Remove and discard gasket (40).
41
44
43
42
397-1628
NOTE
Inspect grommet if sight gauge is removed
and replace grommet if damaged.
8.
Remove six nuts (50), washers (51), retainer (52),

plate (53), grommet (54), and window (55) from
hydraulic tank (1). Discard nuts.
9.
Remove two bolts (47), washers (48), plate (49), tube

(46), and preformed packing (45). Discard preformed
packing.
45
55
54
46
53
47
52
51
50
49
48
397-1629

0339 00-5
TM 5-3805-261-23-2
0339 00
ASSEMBLY
1.
Install new preformed packing (45), tube (46), plate

(49), two washers (48), and bolts (47) on hydraulic
tank (1).
2.
Install window (55), grommet (54), plate (53), retainer

(52), six washers (51), and new nuts (50).
45
55
46
54
53
47
52
51
49
50
48
397-1629
3.
Install new gasket (40) on hydraulic tank (1).
4.
Align matchmarks and install cover (41), 48 bolts

(42), washers (43), and nuts (44). Tighten nuts to 28
lb-ft (38 Nm).
40
1
41
44
43
42
397-1628
0339 00-6
TM 5-3805-261-23-2
0339 00
NOTE
Perform step 5 for each of two valve assemblies.
5.
Install washers (33), spring (39), valve (34), seat (31),

spring (35), retainer (38), spacer (37), and new locknut
(36) on bolt (32).
35
36
37
34
38
33
31
32
39
397-1627
6.
Install two seat (31) assemblies on top of hydraulic

tank (1).
31
1
397-1626
0339 00-7
TM 5-3805-261-23-2
0339 00
7.
Install plugs (24 and 22).
8.
Install bracket (25 and 21), four washers (27), and

bolts (26).
9.
Install plate (28), two washers (30), nuts (29), and

bolts (23). Tighten two nuts to 28 lb-ft (38 Nm).
1
29
30
21
28
27
22
26
23
25
24
INSTALLATION
WARNING
NOTE
Hydraulic tank weighs 250 lb (113 kg).
0339 00-8
397-1625
TM 5-3805-261-23-2
0339 00
1.
With assistance, attach sling to hydraulic tank (1).
2.
Position hydraulic tank (1) on machine.
SLING
NOTE
Steps 3 through 5 cover the left support
and hardware. Follow these instructions
for the right support and hardware.
3.
Install support (20), bolt (13), washers (14 and 15),

mount (16), washers (18 and 19), and nut (17).
13
14
20
15
19
18
16
17
4.
5.
6.
397-1624
Install bolt (10), washers (11 and 12), mount (2), washers (3 and 4), and nut (5). Tighten nut to 40 lb-ft (54 Nm).
Install two brackets (9), spacers (8), washers (6), and bolts (7).
Remove sling from hydraulic tank (1).
SLING
2
3
4
12
10
11
9
8
6
0339 00-9
397-1623
TM 5-3805-261-23-2

7.
Install hydraulic tank filters (WP 0231 00).
8.
Install oil temperature switch (WP 0116 00).
9.
Install tank lines and fittings (WP 0250 00).
10.
Fill hydraulic tank (WP 0216 00).
11.
Start engine (TM 5-3805-261-10). Run engine 1 minute to allow air to bleed from hydraulic system.
12.
Stop engine and check for leaks.
13.
Check hydraulic oil level and fill as necessary (WP 0216 00).
END OF WORK PACKAGE
0339 00-10
0339 00
TM 5-3805-261-23-2
BLADE LIFT BAR ASSEMBLY MAINTENANCE
0340 00

INITIAL SETUP
Personnel Required
Maintenance Level
Direct Support
Two

References
WP 0020 00

Nut, fastener (Item 47, WP 0348 00)

Stud, plain (Item 86, WP 0348 00)


Materials/Parts
Engine off (TM 5-3805-261-10)

Lockwasher (3)
Seal (9)
Centershift lock assembly removed (WP 0260 00)
Bearing (6)
0340 00-1
TM 5-3805-261-23-2
BLADE LIFT BAR ASSEMBLY MAINTENANCE - CONTINUED
0340 00
REMOVAL
WARNING
NOTE
Centershift cylinder weighs 40 lb (18 kg).
1.
Attach sling to centershift cylinder (2).
2.
Remove two bolts (8), lockwashers (7), cap (6), shim(s) (4 and 5), inserts (3 and 9), and shim(s) (10 and 11). Move centershift cylinder (2) clear of blade lift bar (1). Discard lockwashers.
3.
Remove sling.
NOTE
Left side blade lift cylinder not shown for clarity.
Place centershift lock assembly hoses on top of frame.
3 4 5 6
7
11
10 9
397-1674
0340 00-2
TM 5-3805-261-23-2
0340 00
REMOVAL - CONTINUED
4.
Remove bolt (14), lockwasher (13), and clip (12) from blade lift bar (1) and move hose assembly (23) to one side. Discard lockwasher.
WARNING
NOTE
Blade lift bar weighs 200 lb (91 kg).
5.
Attach sling to blade lift bar (1).
6.
Remove two bolts (19), washers (20), and lock (21) from left side of blade lift arm (15).
7.
Remove pin (22) and two washers (16, 17, and 18).
13
12
14
15
16
17
18
19
20
21
23
22
18
0340 00-3
17
16
397-1675
TM 5-3805-261-23-2
0340 00
REMOVAL - CONTINUED
8.
9.
Remove two bolts (24), washers (25), and lock (30)

from right side blade lift arm (15).
24
Remove pin (29) and washers (26, 27, and 28).
25
15
30
29
28 27
26
397-1676
10.
Remove blade lift bar (1) from blade lift arms (15) and
place in work area.
11.
Remove sling.
15
15
1
397-1677
DISASSEMBLY
1.
Use adapter puller to remove eight seals (36) and four

bearings (35). Discard seals and bearings.
2.
Use adapter puller to remove seal (31), ring (32), bearing (33), and bearing (34) from blade lift bar (1). Discard seal and bearings.
34
31
32
35
33
36
397-1678

ASSEMBLY
1.
Install ring (32) in blade lift bar (1).
2.
Use adapter puller, stud, nut, washer, and both hydraulic pullers to install new bearing (34), and new bearing (33). Bearings must seat on ring (32)
0340 00-4
TM 5-3805-261-23-2
0340 00
3.
Use driver to install new seal (31). Lip of seal should be toward outside surface. Seal should contact ring (32).
4.
Use adapter puller, stud, nut, washer, and both hydraulic pullers to install four new bearings (35). Four bearings should
be at a depth of 0.390 to 0.422 in. (9.91 to 10.72 mm) from outside surfaces of blade lift bar (1).
5.
Install eight new seals (36). Lip of eight seals should be toward outside of bore. Eight seals should be even with outside
surface of blade lift bar (1).
INSTALLATION
WARNING
NOTE
Blade lift bar weighs 200 lb (91 kg).
1.
Attach sling to blade lift bar (1).
2.
Position blade lift bar (1) at blade lift arms (15).
3.
Install two washers (26, 27, and 28) between blade lift bar (1) and blade lift arms (15).
4.
Install pin (29). Groove in pin must align with opening in blade lift arm (15).
5.
Install lock (30), two washers (25), and bolts (24).
6.
Install washers (16, 17, and 18) between blade lift bar (1), and blade lift arms (15).
7.
Install pin (22). Groove in pin must align with opening in blade lift arm (15).
8.
Install lock (21), two washers (20), and bolts (19).
9.
Remove sling from blade lift bar (1).
10.
Install clip (12), new lockwasher (13), and bolt (14) in blade lift bar (1).
13
12
14
15
16
17
18
19
20
22
18
0340 00-5
17
16
21
397-1675A
TM 5-3805-261-23-2
0340 00
WARNING
NOTE
Centershift cylinder weighs 40 lb (18 kg).
11.
Attach sling to center shift cylinder (2).
12.
Position centershift cylinder (2).
13.
Install shim(s) (10 and 11), inserts (3 and 9), shim(s) (4 and 5), cap (6), two new lockwashers (7), and bolts (8).
14.
Remove sling.
3 4 5 6
7
11
15.
397-1674
10 9
Install centershift lock assembly (WP 0260 00).
END OF WORK PACKAGE
0340 00-6
TM 5-3805-261-23-2
BLADE LIFT ARM REPLACEMENT
0341 00

INITIAL SETUP
Materials/Parts
Maintenance Level
Direct Support
Seal (8)

0348 00)
Personnel Required
Two
References
WP 0020 00

Driver set, bushing (Item 22, WP 0348 00)

Expander assembly (Item 23, WP 0348 00)
Nut (Item 48, WP 0348 00)

Engine off (TM 5-3805-261-10)

Blade lift cylinders removed (WP 0335 00)
Blade lift bar assembly removed (WP 0340 00)
0341 00-1
TM 5-3805-261-23-2
BLADE LIFT ARM REPLACEMENT - CONTINUED
0341 00
REMOVAL
WARNING
NOTE
Blade lift arm weighs 200 lb (91 kg).
This procedure covers replacement of right side blade lift arm. Follow these instructions for left side
blade lift arm, except as noted.
1.
Attach sling to blade lift arm (5) in center of machine frame.
2.
Remove two bolts (4), washers (3), and locks (2).
3.
Remove bolt (7), washer (1), and plate (6) from right side blade lift arm (5) only.
2
1
4
SLING
5
7
6
397-1680
0341 00-2
TM 5-3805-261-23-2
0341 00
REMOVAL - CONTINUED
4.
Remove pin (9), four washers (8), two washers (11), and blade lift arm (10).
5.
Remove sling.
6.
Remove four seals (12) and two bearings (13). Discard seals.
10
8
11
11
12
13
12
397-1681
7.
Remove two bolts (14), washers (15), retainer (16),

seals (17 and 18), shim(s) (19, 24, and 25), and washers (21, 22, and 23) from arm (5) and yoke (20). Discard seals.
20
14
15
16
17
18
19
25
0341 00-3
24 23 22
21
397-1682
TM 5-3805-261-23-2
0341 00
REMOVAL - CONTINUED
WARNING
NOTE
Weight of yoke is 40 lb (18 kg).
8.
Remove yoke (20) from blade lift arm (5).
CAUTION
Use saw to cut down length of each bearing. Be careful not to cause damage to inside surface of lift arm.
9.
20
Remove and discard bearings (26 and 27).
26
5
27
10.
397-1683
20
Remove washers (28, 29, and 30), seals (32 and 33),
and ring (31) from yoke (20). Discard seals.
29
30
28
33
0341 00-4
32
31
397-1684
TM 5-3805-261-23-2
0341 00

INSTALLATION
1.
Install ring (31), new seals (32 and 33), and washers (28, 29, and 30) on yoke (20). Use expander assembly to install
seals.
NOTE
20
Install bearings so contact is made with

shoulders in arm.
2.
3.
4.
Use puller adapter, hydraulic pump, screw, puller

adapter, nut, and washer to install new bearings (26
and 27) in blade lift arm (5).
Install yoke (20) in blade lift arm (5).
Install washers (21, 22, and 23), shims (19, 24, and
25), new seals (17 and 18), retainer (16), two washers
(15), and bolts (14). Use shims (19, 24, and 25) to get
0.01 in. (0.3 mm) maximum end clearance of yoke
(20). Yoke must rotate freely on blade lift arm (5).
14
15
16
17
18
19
25
22
24 23
21
397-1682
5.
Use puller adapter, hydraulic pump, screw, puller adapter, nut, and washer to install two new bearings (13) in center of
machine frame. Install bearings to a depth of 0.359 to 0.391 in. (9.12 to 9.93 mm).
6.
Use bushing driver set to install four new seals (12). Lips of seals must be toward outside and even with outside surface.
7.
Attach sling to blade lift arm (10) and position on frame.
8.
Install blade lift arm (10), two washers (11), four washers (8), and pin (9).
10
8
11
11
12
13
12
397-1681
0341 00-5
TM 5-3805-261-23-2
0341 00
NOTE
Groove in pin must align with opening in blade lift arm.
9.
Install plate (6), washer (1), and bolt (7) on right side
blade lift arm (5) only.
10.
Install two lock (2), washers (3), and bolts (4).
11.
Remove sling.
2
1
4
SLING
5
7
6
397-1680
12.
Install blade lift bar assembly (WP 0340 00).
13.
Install blade lift cylinders (WP 0335 00).
END OF WORK PACKAGE
0341 00-6
TM 5-3805-261-23-2
DRAWBAR ASSEMBLY REPLACEMENT
0342 00

INITIAL SETUP
References
Maintenance Level
WP 0020 00
Direct Support


0348 00)
Shop, equipment, contact torch (Item 77, WP 0348

00)
Engine off (TM 5-3805-261-10)
Circle drive motor removed (WP 0217 00)
Circle drive motor lines removed (WP 0225 00)

Centershift cylinder lines removed (WP 0226 00)
Materials/Parts
Toolbox removed (WP 0202 00)
Centershift cylinder disconnected (WP 0243 00)
Personnel Required
Circle assembly removed (WP 0344 00)

Scarifier removed (WP 0264 00)
Two
0342 00-1
TM 5-3805-261-23-2
DRAWBAR ASSEMBLY REPLACEMENT - CONTINUED
0342 00
REMOVAL
WARNING
NOTE
Drawbar weighs 500 lb (227 kg).
1.
Attach sling to front of drawbar (1).
2.
Position jack stands under three corners of drawbar (1).
NOTE
This procedure covers replacement of the right drawbar assembly. Follow these instructions for the left
drawbar assembly.
3.
Use hydraulics to lower rear of drawbar (1) onto jack stands.
4.
Remove two bolts (8), washers (7), cap (6), two shims (5), inserts (3 and 4), and two shims (2) from rear corners of
drawbar (1).
SLING
2
3
4
5
6
JACK STANDS
8
0342 00-2
397-1686
TM 5-3805-261-23-2
0342 00
REMOVAL - CONTINUED
5.
Remove four bolts (9), washers (11), and two bolts

(10) at front of drawbar (1).
6.
Slide cap (12) onto drawbar (1).
7.
Lower front of drawbar (1) onto jack stands with sling.
8.
Remove sling.
9.
Remove adapter (13) and shims (14 and 15) from front
corner of drawbar (1).
SLING
1
10
11
12
15 14
13
JACK STAND
397-1687
10.
Remove five bolts (17), ball (16), fitting (18), and cap
(12) from drawbar (1).
12
16
17
1
JACK STAND
18
397-1688

INSTALLATION
1.
Install cap (12), fitting (18), ball (16), and five bolts (17) on front cover of drawbar (1).
2.
Measure end play between ball (16) and face of cap (12). Clearance must be 0.0 to 0.02 in. (0.0 to 0.5 mm).
3.
Install shims (14 and 15) and adapter (13).
0342 00-3
TM 5-3805-261-23-2
0342 00
WARNING
NOTE
SLING
Drawbar weighs 500 lb (227 kg).

Attach sling to front of drawbar (1).
5.
Raise front of drawbar (1) into mounting position.
6.
Install two bolts (10), four washers (11), and bolts (9)
in cap (12) at front corner of drawbar (1). Tighten
bolts to 367 to 397 lb-ft (498 to 538 Nm).
11
4.
10
12
15 14
JACK STAND
7.
8.
9.
10.
13
397-1687
Remove sling.
Install two shims (2), inserts (3 and 4), two shims (5), cap (6), two washers (7), and bolts (8) in rear corners of drawbar
(1).
Use hydraulics to raise rear of drawbar (1).
Remove jack stands.
SLING
2
4
5
6
JACK STANDS
8
0342 00-4
397-1686
TM 5-3805-261-23-2

11.
Install circle assembly (WP 0344 00).
12.
Connect centershift cylinder (WP 0320 00).
13.
Install tool box (WP 0202 00.
14.
Install centershift cylinder lines (WP 0226 00).
15.
Install circle drive motor lines (WP 0225 00).
16.
Install circle drive motor (WP 0217 00).
17.
Install scarifier (WP 0208 00).
END OF WORK PACKAGE
0342 00-5/(-6 Blank)
0342 00
TM 5-3805-261-23-2
BLADE BRACKETS REPLACEMENT
0343 00

INITIAL SETUP
References
Maintenance Level
WP 0020 00
Direct Support

0348 00)


Engine off (TM 5-3805-261-10)
Rope
Materials/Parts
Blade assembly removed (WP 0259 00)
Blade tip cylinder removed (WP 0334 00)
Pin, cotter
Side shift cylinder removed (WP 0337 00)
0343 00-1
TM 5-3805-261-23-2
BLADE BRACKETS REPLACEMENT - CONTINUED
0343 00
REMOVAL
1.
Support bar (10) by tying both ends to frame with rope.
WARNING
NOTE
Old style bracket weighs 72 lb (33 kg); new style bracket weighs 50 lb (23 kg).
2.
Attach sling to bracket (1).
NOTE
New style bracket does not have nut (6) and washers (4 and 5).
3.
Remove cotter pin (8), nut (9), washer (7), nuts (3 and 6), washers (4 and 5), bolt (2), and bracket (1). Discard cotter pin.
4.
Remove two washers (11).
SLING
2
3
4
5
6
7
11
10
9
OLD STYLE BRACKET SHOWN
0343 00-2
397-1690
TM 5-3805-261-23-2
0343 00
REMOVAL - CONTINUED
5.
Remove sling.
6.
Remove nuts (12 and 15).
7.
8.
Remove bar (10) and attached rope.
9.
Remove rope from bar (10).
ROPE
12
13
14
10
15
397-1691
NOTE
SLING
Bracket weighs 68 lb (31 kg).

10.
NOTE
16
Tie shims together and tag for identification.

11.
Remove two bolts (21), washers (22), bolts (20),

washers (19), cap (18), and ten shims (17) from
bracket (16).
17
18
22
21
0343 00-3
19
20
397-1692
TM 5-3805-261-23-2
0343 00
REMOVAL - CONTINUED
12.
Remove bracket (16) from circle (23).
13.
Remove shaft (25) from pipe (24).
14.
Remove sling.
SLING
23
16
24
397-1693
25
INSTALLATION
1.
Position shaft (25) in pipe (24) at bottom rear of circle (23).
WARNING
NOTE
SLING
Bracket weighs 68 lb (31 kg).

2.
3.
Install bracket (16) in circle (23).
4.
Install ten shims (17), cap (18), two washers (19),

bolts (20), washers (22), and bolts (21).
5.
Remove sling from bracket (16).
6.
Install bar (10). Align tapped holes in bar with holes in

bracket (16).
17
7.
Support bar (10) by tying both ends to frame with

rope.
18
8.
9.
Install nuts (12 and 15).
16
0343 00-4
22
21
20
19
397-1692
TM 5-3805-261-23-2
0343 00
NOTE
SLING
2
Old style bracket weighs 72 lb (33 kg);

new style bracket weighs 50 lb (23 kg).
10.
11.
Install two washers (11). Use washers as required to

get sliding fit of bracket (1) with maximum 0.07 in.
(1.8 mm) clearance between bracket and circle wear
plate.
3
4
12.
13.
Install bolt (2), washers (4 and 5), and nut (6).
14.
Back out nut (12) to make contact with bracket (1).
15.
Install nut (3) and tighten to 1,200 lb-ft (1,627 Nm).
16.
Install washer (7) and nut (9) to bar (10). Tighten nut
to remove any clearance, then back off enough to permit installation of new cotter pin (8).
17.
18.
Remove rope and sling.
19.
Install side shift cylinder (WP 0337 00).
20.
Install blade tip cylinder (WP 0334 00).
21.
Install blade assembly (WP 0259 00).
11
10
9
OLD STYLE BRACKET SHOWN
397-1690
ROPE
12
13
14
16
15
397-1691
END OF WORK PACKAGE

0343 00-5/(-6 Blank)
TM 5-3805-261-23-2
CIRCLE ASSEMBLY REPLACEMENT
0344 00

INITIAL SETUP
Maintenance Level
Locknut (8)
Direct Support
Pin, cotter (2)

References
00)
WP 0020 00

Engine off (TM 5-3805-261-10)
Materials/Parts
Blade brackets removed (WP 0343 00)
0344 00-1
TM 5-3805-261-23-2
CIRCLE ASSEMBLY REPLACEMENT - CONTINUED
0344 00
REMOVAL
1.
Remove two nuts (7), washers (8), and bolts (1) from drawbar assembly (2).
2.
Remove two cotter pins (6), washers (5), pin (4), and guide (3). Discard cotter pins.
3
4
5
8
3.
Use jack stands to support circle (11).
4.
Loosen eight nuts (9).
5.
Turn eight setscrews (10) all the way down.
397-1695
11
10
397-1696
0344 00-2
TM 5-3805-261-23-2
0344 00
REMOVAL - CONTINUED
NOTE
Tag and bundle shims to aid in installation.
6.
Remove 8 locknuts (20), washers (22), bolts (13),

washers (12), 4 bolts (19), washers (18), shoes (17),
24 shims (16), 28 shims (15), 8 strips (14), and 4 strips
(21) from drawbar assembly (2). Discard locknuts.
12
13
14
15
22
16
17
21
18
19
20
397-1697
WARNING
NOTE
Circle weighs 1,050 lb (476 kg).
SLING
7.
Attach sling to circle (11).
8.
Remove jack stands.
9.
Turn battery disconnect switch to the ON position and

10.
Move machine back to remove circle drive motor pinion (23) from engagement in circle (11). Lift drawbar
assembly (2) away from circle.
11.
Stop engine.
12.
Lower circle (11) to ground.
13.
Remove circle (11) from under machine.
14.
Remove sling.
23 (HIDDEN)
11
2
JACK STANDS
0344 00-3
397-1698
TM 5-3805-261-23-2
0344 00

INSTALLATION
WARNING
NOTE
Circle weighs 1,050 lb (476 kg).
1.
Attach sling to circle (11) under machine.
2.
Raise circle (11) into mounting position under

machine.
SLING
3.
Support circle (11) with jack stands.
4.
Turn battery disconnect switch to the ON position and

5.
Lower drawbar assembly (2) into position over circle

(11). Move machine slowly forward to engage circle
drive motor pinion (23) into circle (11).
6.
Stop engine.
23 (HIDDEN)
11
2
JACK STANDS
0344 00-4
397-1698
TM 5-3805-261-23-2
0344 00
NOTE
7.
8.
Be sure jack stand is not supporting circle when measuring clearance.
Do not tighten bolts. Use shim(s) as required to obtain 0.020 in. (0.51 mm) maximum clearance
between drawbar, strip, and circle at each shoe.
Install 4 strips (21), 8 strips (14), 28 shims (15), 24

shims (16), 4 shoes (17), washers (18), bolts (19), 8
washers (12), bolts (13), washers (22), and new locknuts (20) on drawbar assembly (2).
13
12
14
Remove sling.
15
22
16
17
21
18
19
20
9.
With shoes (17) and shims (15) in position on drawbar

assembly (2), adjust four shoes.
10.
Loosen eight nuts (9) on setscrews (10).
11.
Tighten setscrews (10) until shoes are against inside of

circle (11).
12.
Loosen setscrews (10) until circle (11) is just free to

turn.
13.
Tighten nuts (9) on setscrews (10).
397-1697
14
15
9
0.020 IN.
(0.51 MM)
MAXIMUM
11
10
0344 00-5
17
0.031 IN.
(0.79 MM)
MAXIMUM397-1699
TM 5-3805-261-23-2
0344 00
14.
Tighten four bolts (19) and eight bolts (13) to 310 to

340 lb-ft (420 to 461 Nm). Recheck clearances and
adjustments.
15.
Remove jack stands from under circle (11).
13
19
11
JACK STAND
16.
Install guide (3), pin (4), two washers (5), and new
cotter pins (6).
17.
Install two bolts (1), washers (8), and nuts (7).
397-1696A
3
4
5
8
18.
Install blade brackets (WP 0343 00).
END OF WORK PACKAGE
0344 00-6
397-1695
TM 5-3805-261-23-2
CIRCLE DRIVE SWIVEL ASSEMBLY REPAIR
0345 00

INITIAL SETUP
References
Maintenance Level
Direct Support
WP 0020 00

0348 00)

Materials/Parts
Engine off (TM 5-3805-261-10)
Lockwasher (4)
Circle drive swivel assembly removed (WP 0263

00)
Seal (11)
DISASSEMBLY
1.
Remove two screws (1), retainer (2), and shim(s) (3)

from body (6).
2.
Remove and discard seals (4 and 5).
1
2
3
4
5
397-1703
0345 00-1
TM 5-3805-261-23-2
CIRCLE DRIVE SWIVEL ASSEMBLY REPAIR - CONTINUED
0345 00
3.
Remove four bolts (12), lockwashers (13), and cover

(11) from body (6). Discard lockwashers.
4.
Remove and discard four preformed packings (10).
5.
Use bearing puller attachment to remove rotor (9)

from body (6).
6.
Remove and discard seven seals (7) and preformed

packings (8).
7
8
9
10
13
11
12
397-1704
7.
Remove and discard seals (14 and 15) from rotor (9).
14
15
397-1705

0345 00-2
TM 5-3805-261-23-2
CIRCLE DRIVE SWIVEL ASSEMBLY REPAIR - CONTINUED
0345 00
ASSEMBLY
1.
Lubricate new seals (14 and 15) with clean oil and install on rotor (9).
2.
Lubricate seven new preformed packings (8) and new seals (7) with clean oil and install in body (6).
3.
Install rotor (9) in body (6).
4.
Lubricate four new preformed packings (10) with clean oil and install in cover (11).
5.
Install cover (11), four new lockwashers (13), and bolts (12) in body (6).
6.
Lubricate new seals (4 and 5) with clean oil.
NOTE
Add or remove shim(s) to obtain required gap.
7.
Install seals (4 and 5), shim (s) (3), retainer (2), and
two screws (1) in body (6).
8.
Use feeler gauge to measure gap between retainer (2)

and body (6). Gap should be 0.005 to 0.020 in. (0.13 to
0.51 mm).
1
2
3
4
5
397-1703
9.
Install circle drive swivel assembly (WP 0263 00).
END OF WORK PACKAGE
0345 00-3/(-4 Blank)
TM 5-3805-261-23-2
CHAPTER 5
SUPPORTING INFORMATION
TM 5-3805-261-23-2
REFERENCES
0346 00
SCOPE
This work package lists all publication indexes, forms, field manuals, technical bulletins, technical manuals and other
publications referenced in this manual and which apply to maintenance of the 130G Grader.
PUBLICATION INDEXES
The following indexes should be consulted frequently for latest changes or revisions and for new publications relating to
material covered in this technical manual.
Consolidated Army Publications and Forms Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DA PAM 25-30
Functional Users Manual for the Army Maintenance Management System (TAMMS) . . . . . . . . . . . . . . . . . . . .
PAM 750-8
FORMS
NOTE
Refer to PAM 750-8, Functional Users Manual for the Army Maintenance Management System
(TAMMS), for instructions on the use of maintenance forms.
Accident Identification Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DD Form 518
Equipment Inspection and Maintenance Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DA Form 2404, DA Form 5988-E
Maintenance Request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DA Form 2407
Motor Vehicle Accident Report. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SF Form 91
Product Quality Deficiency Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SF Form 368
Recommended Changes to Publications and Blank Forms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DA Form 2028
Uncorrected Fault Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DA Form 2408-14
FIELD MANUALS
Army Motor Transport Unit and Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .FM 55-30
Basic Cold Weather Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .FM 31-70
Chemical and Biological Contamination Avoidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM 3-11.3
Desert Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .FM 90-3
First Aid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM 4-25.11
NBC Decontamination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..FM 3-11.5
NBC Field Handbook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .FM 3-7
Northern Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .FM 31-71
Nuclear Contamination Avoidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM 3-3-1
Operations and Maintenance of Ordnance Materiel in Cold Weather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .FM 9-207
Recovery and Battlefield Damage Assessment and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM 9-43-2
Rigging Techniques, Procedures, and Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .FM 5-125
TECHNICAL BULLETINS
CARC Spot Painting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB 43-0242
Color, Marking, and Camouflage Painting of Military Vehicles, Construction Equipment
and Materials Handling Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB 43-0209
Solder and Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB SIG 222
0346 00-1
TM 5-3805-261-23-2
REFERENCES - CONTINUED
0346 00
TECHNICAL BULLETINS - CONTINUED

Use of Antifreeze Solutions, Antifreeze Extender, Cleaning Compounds and Test Kit in Engine
Cooling Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB 750-651
TECHNICAL MANUALS
Inspection, Care, and Maintenance of Antifriction Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 9-214
Materials Used for Cleaning, Preserving, Abrading and Cementing Ordnance Materiel and
Related Materiels Including Chemicals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 9-247
Operators and Organizational Maintenance Manual Including RPSTL
for STE/ICE-R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 9-4910-571-12&P
Operators Manual for the 130G Grader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 5-3805-261-10
Operators, Unit, Direct Support, and General Support Maintenance
Manual for Lead-Acid Storage Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 9-6140-200-14
Painting Instructions for Army Materiel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 43-0139
Procedures for Destruction of Equipment to Prevent Enemy Use (Mobility Equipment Command) . . . . . . . . . . TM 750-244-3
Transportability Guidance for the 130G Grader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TM 55-3805-261-14
Unit, Direct Support and General Support Including Depot Maintenance RPSTL for the 130G Grader. . . TM 5-3805-261-24P
OTHER PUBLICATIONS
Abbreviations and Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASME Y14.38-1999
Army Medical Department Expendable/Durable Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CTA 8-100
Expendable/Durable Items (Except Medical, Class V Repair Parts, and Heraldic Items) . . . . . . . . . . . . . . . . . . . . .CTA 50-970
Fuels and Lubricants Standardization Policy for Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AR 70-12
Operators Circular for Welding Theory and Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TC 9-237
END OF WORK PACKAGE
0346 00-2
TM 5-3805-261-23-2
MAINTENANCE ALLOCATION CHART (MAC) INTRODUCTION
0347 00
THE ARMY MAINTENANCE SYSTEM MAC

1.
This introduction provides a general explanation of all maintenance and repair functions authorized at the two maintenance levels under the Two-Level Maintenance System concept.
2.
The MAC immediately following this introduction designates overall authority and responsibility for the performance
of maintenance functions on the identified end item or component. The application of the maintenance functions to the
end item or component shall be consistent with the capacities and capabilities of the designated maintenance levels,
which are shown in the MAC (WP 0348 00) in column (4) as:
Field - includes subcolumns:
C - Operator/Crew
O - Unit
F - Direct Support
Sustainmant - includes subcolumns:
H - General Support
D - Depot
3.
The tools and test equipment requirements (immediately following the MAC) list the tools and test equipment (both special tools and common tool sets) required for each maintenance function as referenced from the MAC.
4.
The remarks (immediately following the tools and test equipment requirements) contain supplemental instructions and
explanatory notes for a particular maintenance function.
MAINTENANCE FUNCTIONS
Maintenance functions are limited to and defined as follows:
1.
Inspect. To determine the serviceability of an item by comparing its physical, mechanical, and/or electrical characteristics with established standards through examination (e.g., by sight, sound, or feel).
2.
Test. To verify serviceability by measuring the mechanical, pneumatic, hydraulic, or electrical characteristics of an item
and comparing those characteristics with prescribed standards on a scheduled basis, i.e., load testing of lift devices and
hydrostatic testing of pressure hoses.
3.
Service. Operations required periodically to keep an item in proper operating condition; e.g., to clean (includes decontaminate, when required), preserve, drain, paint, or replenish fuel, lubricants, chemical fluids, or gases.
4.
Adjust. To maintain or regulate, within prescribed limits, by bringing into proper position, or by setting the operating
characteristics to specified parameters.
5.
Align. To adjust specified variable elements of an item to bring about optimum or desired performance.
6.
Calibrate. To determine and cause corrections to be made or to be adjusted on instruments of test, measuring, and diagnostic equipment used in precision measurement. Calibration consists of comparisons of two instruments, one of which
is a certified standard of known accuracy, to detect and adjust any discrepancy in the accuracy of the instrument being
compared.
7.
Remove/Install. To remove and install the same item when required to perform service or other maintenance functions.
Installation may be the act of emplacing or seating a spare, repair part, or module (component or assembly) into position
in a manner to allow the proper functioning of an equipment or system.
8.
Replace. To remove an unserviceable item and install a serviceable counterpart in its place. Replacement is authorized
by the MAC and the assigned maintenance level is shown as the third position code of the Source, Maintenance and
Recoverability (SMR) code.
9.
Repair. Repair is the application of maintenance services, including fault location/troubleshooting, removal/installation,
disassembly/assembly procedures, and maintenance actions to identify troubles and restore serviceability to an item by
correcting specific damage, fault, malfunction, or failure in a part, subassembly, module (component or assembly), end
item, or system.
0347 00-1
TM 5-3805-261-23-2
MAINTENANCE ALLOCATION CHART (MAC) INTRODUCTION - CONTINUED
0347 00
MAINTENANCE FUNCTIONS - CONTINUED
NOTE
The following definitions are applicable to the repair maintenance function:
Services - Inspecting, testing, service, adjustment, alignment, calibration, and/or replacement.
Fault location/troubleshooting - The process of investigating and detecting the cause of equipment malfunctioning; the act of isolating a fault within a system or Unit Under Test (UUT).
Disassembly/assembly - The step-by-step breakdown (taking apart) of a spare/functional group coded

item to the level of its least component, assigned a SMR code for the level of maintenance under consideration (i.e., identified as maintenance significant).
Actions - Welding, grinding, riveting, straightening, facing, machining, and/or resurfacing.
10.
Overhaul. That maintenance effort (service/action) prescribed to restore an item to a completely serviceable/operational
condition as required by maintenance standards in appropriate technical publications. Overhaul is normally the highest
degree of maintenance performed by the Army. Overhaul does not normally return an item to like new condition.
11.
Rebuild. Consists of those services/actions necessary for the restoration of unserviceable equipment to a like new condition in accordance with original manufacturing standards. Rebuild is the highest degree of materiel maintenance
applied to Army equipment. The rebuild operation includes the act of returning to zero those age measurements (hours/
miles, etc.) considered in classifying Army equipment/components.
EXPLANATION OF COLUMNS IN THE MAC, TABLE 1

1.
Column (1) - Group Number. Column (1) lists Group numbers, the purpose of which is to identify maintenance significant components, assemblies, subassemblies, and modules with the Next Higher Assembly (NHA).
2.
Column (2) - Component/Assembly. Column (2) contains the item names of components, assemblies, subassemblies,
and modules for which maintenance is authorized.
3.
Column (3) - Maintenance Function. Column (3) lists the functions to be performed on the item listed in Column (2).
(For a detailed explanation of these functions refer to Maintenance Functions outlined above).
4.
Column (4) - Maintenance Level. Column (4) specifies each level of maintenance authorized to perform each function
listed in column (3), by indicating work time required (expressed as manhours in whole hours or decimals) in the appropriate subcolumn. This work time figure represents the active time required to perform that maintenance function at the
indicated level of maintenance. If the number or complexity of the tasks within the listed maintenance function varies at
different maintenance levels, appropriate work time figures are to be shown for each level. The work time figure represents the average time required to restore an item (assembly, subassembly, component, module, end item, or system) to
a serviceable condition under typical field operating conditions. This time includes preparation time (including any necessary disassembly/assembly time), troubleshooting/fault location time, and quality assurance time in addition to the
time required to perform the specific tasks identified for the maintenance functions authorized in the MAC. The symbol
designations for the various maintenance levels are as follows:
Field:
C - Operator/Crew Maintenance
O - Unit Maintenance
F - Direct Support Maintenance
Sustainment:
H - General Support Maintenance
D - Depot Maintenance
0347 00-2
TM 5-3805-261-23-2
MAINTENANCE ALLOCATION CHART (MAC) INTRODUCTION - CONTINUED
0347 00
EXPLANATION OF COLUMNS IN THE MAC, TABLE 1- CONTINUED
NOTE
The L maintenance level is not included in column (4) of the MAC. Functions to this level of maintenance
are identified by a work time figure in the H column of column (4), and an associated reference code is
used in the REMARKS CODE column (6). This code is keyed to the remarks, and the SRA complete repair
application is explained there.
5.
Column (5) - Tools and Equipment Reference Code. Column (5) specifies, by code, common tool sets (not individual
tools), common Test, Measurement, and Diagnostic Equipment (TMDE), special tools, special TMDE, and special support equipment required to perform the designated function. Codes are keyed to the entries in the tools and test equipment table.
6.
Column (6) - Remarks Code. When applicable, this column contains a letter code, in alphabetical order, which is
keyed to the remarks table entries (Table 3).
EXPLANATION OF COLUMNS IN THE TOOLS AND TEST EQUIPMENT REQUIREMENTS, TABLE 2

1.
Column (1) - Tool or Test Equipment Reference Code. The tool and test equipment reference code correlates with a
code used in column (5) of the MAC.
2.
Column (2) - Maintenance Level. The lowest level of maintenance authorized to use the tool or test equipment.
3.
Column (3) - Nomenclature. Name or identification of the tool or test equipment.
4.
Column (4) - National Stock Number (NSN). The NSN of the tool or test equipment.
5.
Column (5) - Tool Number (ICAGEC). The manufacturer's part number, model number, or type number. The manufacturers Commercial and Government Entity Code (CAGEC) is also included.
EXPLANATION OF COLUMNS IN THE REMARKS, TABLE 3

1.
Column (1) - Remarks Code. The code recorded in column (6) of the MAC.
2.
Column (2) - Remarks. This column lists information pertinent to the maintenance function being performed as indicated in the MAC.
END OF WORK PACKAGE
0347 00-3/(-4 Blank)
TM 5-3805-261-23-2
MAINTENANCE ALLOCATION CHART (MAC)
0348 00
Table 1. Maintenance Allocation Chart (MAC) for the 130G Series Grader .
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
FIELD
GROUP
NUMBER
01
0100
0101
0102
0103
0104
0105
0106
COMPONENT/
ASSEMBLY
ENGINE
Engine Assembly
Crankcase, Block,
Cylinder Head:
Cylinder Block
Cylinder Head
Assembly and Spacer
Plate
Crankshaft:
Crankshaft Hub
Crankshaft Assembly
Flywheel Assembly:
Flywheel
Flywheel Housing
MAINTENANCE
FUNCTION
Test
Service
Replace
UNIT
C
(5)
(6)
SUSTAINMENT
DS
GS
DEPOT
1.0
1.0
12,75,89
75,89
74,78,85,89,
96,100
14.0
Repair
3.0
Inspect
0.8
Inspect
Replace
Repair
4.0
8.0
2.0
Replace
Inspect
Replace
1.5
Replace
Replace
Repair
16.0
10.0
2.0
TOOLS AND
EQUIPMENT REMARKS
REF CODE
CODE
95.0
62,74,
89,94,96
74,78,89,96,101
74,89
54,74,89,101
0.5
35.0
15,74,78,89,101
18,74,78,89
74,89
Pistons, Connecting
Rods:
Piston Assemblies
Replace
Valves, Camshafts, and
Timing System:
Rocker Arm
Adjust
Assembly
Replace
Repair
Valves
Replace
1.0
3.0
1.0
4.0
28,31,74,89,96
28,31,74,89,101
28,31,74,89,101
19,20,25,74,88,
89
Engine Lubrication
System:
Oil Pan
Engine Oil Pump
2.0
4.0
74,89
74,89,96
14.0
Replace
Replace
0348 00-1
TM 5-3805-261-23-2
MAINTENANCE ALLOCATION CHART (MAC) - CONTINUED
0348 00
Table 1. Maintenance Allocation Chart (MAC) for the 130G Series Grader - Continued.
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
FIELD
GROUP
NUMBER
COMPONENT/
ASSEMBLY
03
0301
FUEL SYSTEM
Fuel Injector Nozzle
0302
Governor and Fuel

Injection Pump
Assembly
0304
Air Cleaner
0305
Turbocharger
0306
0308
0309
0311
04
0401
05
0501
0504
Tanks, Lines, and

Fittings Headers:
Fuel Tank
MAINTENANCE
FUNCTION
UNIT
C
(6)
SUSTAINMENT
DS
GS
DEPOT
Test
Replace
Adjust
1.0
1.0
2.0
Replace
Repair
Service
Replace
Replace
Repair
2.0
Service
Replace
Repair
Engine Speed Governor Adjust
and Controls
Replace
Repair
Fuel Filters:
Primary Fuel Filter
Service
Replace
Secondary Fuel Filter Service
Replace
Engine Starting Aids
Service
Replace
Repair
EXHAUST SYSTEM
Muffler and Pipes
Replace
COOLING SYSTEM
Radiator Assembly
Inspect
Service
Replace
Repair
Water Pump:
Water Pump
Replace
Assembly
Repair
(5)
TOOLS AND
EQUIPMENT REMARKS
REF CODE
CODE
87
8,58,74,89
74,89
74,89
4.0
0.3
0.5
0.5
75,89,96
89
74,89,96
1.5
2.0
0.3
A
2.0
2.0
1.0
2.0
3.0
0.2
0.2
75,78,89,96
89
74,89
74,89,96
74,89
0.3
0.5
0.3
0.5
0.5
1.0
1.0
75,89,96
75,89,96
75,89
75,89,96
89
89
89
2.0
75,89
1.0
3.0
3.0
75,89
16,78,89
89
0.2
2.5
1.0
0348 00-2
89
74,89,96
A
D
TM 5-3805-261-23-2
0348 00
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
FIELD
GROUP
NUMBER
05
0505
06
0601
0603
0607
0608
0609
COMPONENT/
ASSEMBLY
MAINTENANCE
FUNCTION
COOLING SYSTEM
- Continued
Fan Assembly:
Fan Drive
Service
Replace
Repair
Fan Belts
Inspect
Adjust
Replace
ELECTRICAL
SYSTEM
Alternator
Test
Replace
Repair
Starting Motor:
Test
Replace
Repair
Instrument or Engine
Control Panel:
Instrument Panel/
Test
Electronic Monitoring Replace
System (EMS)
Repair
Operator's Console
Replace
Assembly
Repair
Miscellaneous Items:
Switches
Replace
Fuse Box and Fuses Replace
NATO Slave
Replace
Receptacle
Lights:
Headlights
Test
Replace
Turn Signal Lights
Test
Replace
UNIT
C
(5)
SUSTAINMENT
DS
GS
DEPOT
TOOLS AND
EQUIPMENT REMARKS
REF CODE
CODE
0.2
0.1
(6)
A
1.0
0.5
0.1
0.2
0.5
75,89
75,89
0.5
1.5
12,75,89
89
74,89
12,75,89
75,89,96
74,89,94,96
75,89
75,89
2.0
0.5
1.0
2.0
0.1
1.0
0.4
1.0
75,89,94
75,89,94
89
89
0.3
0.5
0.5
89
89
89
0.5
89
0.5
89
1.0
0.1
0.1
0348 00-3
TM 5-3805-261-23-2
0348 00
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
FIELD
GROUP
NUMBER
06
0610
0612
0613
07
0705
0710
0714
0719
COMPONENT/
ASSEMBLY
MAINTENANCE
FUNCTION
ELECTRICAL
SYSTEM - Continued
Taillights
Test
Replace
Floodlights
Test
Replace
Sending Units and
Replace
Warning Switches
Batteries, Storage:
Batteries
Inspect
Test
Service
Replace
Battery Boxes
Replace
Repair
Battery Cables
Replace
Hull or Chassis Wiring
Harness:
Small Harness (Lights Test
etc.)
Replace
Repair
TRANSMISSION
Transmission Shifting Adjust
Components
Replace
Transmission Assembly
and Associated Parts:
Transmission
Inspect
Assembly
Test
Service
Replace
Repair
UNIT
C
(5)
(6)
SUSTAINMENT
DS
GS
DEPOT
TOOLS AND
EQUIPMENT REMARKS
REF CODE
CODE
0.1
0.5
89
0.5
0.5
89
75,89,96
0.5
0.5
0.5
0.5
0.5
0.3
12,75
75,89
75,89
89
89
89
0.1
0.2
1.0
0.5
1.0
75,89
74,75,89
75,89
2.5
0.5
1.5
89
75,89,96
0.2
0.2
0.5
8.0
3.0
Servo Unit:
Control Valve
Test
Assembly
Replace
Transfer Shaft, Engine- Replace
to-Transmission
0.5
1.0
2.0
0348 00-4
29.0
75,89
37,74,89
16,17,18,
56,62,74,
89,93
74,89
66,74
37,74,89
TM 5-3805-261-23-2
0348 00
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
FIELD
GROUP
NUMBER
07
0721
COMPONENT/
ASSEMBLY
TRANSMISSION Continued
Oil Cooler, Pump, and
Filters:
Oil Coolers
Oil Pump
Oil Filter
10
1000
1004
FRONT AXLE
Front Axle Assembly
Steering and Leaning

Wheel:
Steering Arm
Assemblies
Leaning Wheel
Mechanism
11
1100
Leaning Wheel
Cylinder
REAR AXLE
Rear Axle Assembly:
MAINTENANCE
FUNCTION
UNIT
C
Replace
Repair
Replace
Service
Replace
DS
GS
DEPOT
TOOLS AND
EQUIPMENT REMARKS
REF CODE
CODE
89
89
37,74,89
75,89
75,89
0.3
0.7
0.3
E
A
0.4
3.0
2.0
33,36,39,53,64,
74,77,89,100
33,36,39,53,64,
74,77,89,100
37,74,84,89,96
11,37,40,49,57,
61,63,65,73,78,
80,82,84,89,92,
96,100
11,37,40,49,57,
61,63,65,73,78,
80,82,84,89,92,
96,100
74,89
1,9,45,50,65,66,
71,74,78,82,89,
100
74,78,89
23,34,74,89,102
10.0
2.0
75,89
74,89
74,89
Repair
5.0
Adjust
Replace
0.3
5.0
Repair
2.0
Adjust
Replace
2.0
4.0
Service
Replace
Repair
0.3
0348 00-5
9,44,60,65,
71,74,75,84,
89,92
5.0
0.5
A
3.0
Replace
Repair
(6)
SUSTAINMENT
1.0
1.0
2.0
Service
Replace
Repair
Service
Replace
(5)
32.0
H
A
I
TM 5-3805-261-23-2
0348 00
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
FIELD
GROUP
NUMBER
11
1103
1105
COMPONENT/
ASSEMBLY
REAR AXLE Continued

Differential
Service
Replace
Differential Lock
Service
Control
Replace
Repair
Final Drive Assembly Service
Replace
Tandem Drive and

Chain Assemblies:
Tandem Drive
Housing
Chain Assemblies
12
1201
MAINTENANCE
FUNCTION
Service
Replace
Repair
Replace
Repair
BRAKES
Handbrakes:
Parking Brake Control Replace
Handle
Parking Brake
Actuator Assembly
1202
Service Brakes
1206
Mechanical Brake
System:
Air Brake Pedal and
Linkage
Adjust
Replace
Repair
UNIT
C
(5)
SUSTAINMENT
DS
GS
DEPOT
0.5
TOOLS AND
EQUIPMENT REMARKS
REF CODE
CODE
10.0
75,89
74,78,89
1.0
1.0
74,89
74,89
0.5
A
18.0
0.3
8.5
8.0
4.5
3.0
7,17,37,41,51,
55,56,62,66,70,
74,77,78,79,83,
89,90,93,102
75,89
66,74,78,89,100
75,89
38,56,66,74,89
38,56,74,89
1.0
89
0.5
1.0
89
74,89
58,63,74,81,
89
74,89
17,33,55,56,74,
78,89,96,100
1.0
0.8
1.5
Adjust
0.5
89
Replace
1.5
89
0348 00-6
A
A
0.5
Adjust
Replace
(6)
A
D
TM 5-3805-261-23-2
0348 00
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
FIELD
GROUP
NUMBER
12
1208
1209
13
1311
1313
14
1410
1411
1412
1414
COMPONENT/
ASSEMBLY
MAINTENANCE
FUNCTION
BRAKES - Continued
Airbrake System:
Brake Control Valve Replace
Air Reservoir
Service
Replace
Repair
Air Compressor
Replace
Assembly
Repair
WHEELS
Wheel Assembly
Replace
(Front)
Wheel Assembly (Rear) Replace
Tires
STEERING
Hydraulic Pump or
Fluid Motor Assembly:
Steering Control
Pump and Steering
Wheel
Supplemental
Steering Pump and
Motor
Hoses, Lines, and
Fittings
Hydraulic Cylinder
Relief Valve
Service
Replace
Repair
UNIT
C
(5)
(6)
SUSTAINMENT
DS
GS
DEPOT
TOOLS AND
EQUIPMENT REMARKS
REF CODE
CODE
0.3
74,89
0.8
89
89
74,89
74,89,96
0.3
A
2.0
4.0
2.0
1.0
37,75,77,78,84,
89,102
37,75,77,78,84,
89,101
1.0
0.3
A
2.0
1.0
75,79,89
89
Replace
Repair
1.5
Replace
4.0
74,89
Replace
2.0
89
Replace
Repair
Test
Replace
Repair
0.5
2.0
2.0
1.0
0.8
3.0
0348 00-7
74,89
74,89,94,96
74,89,100
74,89,101
74,88,89
74,89
32,74,89
TM 5-3805-261-23-2
0348 00
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
FIELD
GROUP
NUMBER
15
1501
1503
18
1801
1808
21
22
2202
COMPONENT/
ASSEMBLY
FRAME, TOWING
ATTACHMENTS,
DRAWBARS, AND
ARTICULATION
SYSTEMS
Frame Assembly:
Front Frame
Assembly
Frame and Case
Assembly, Rear
Pintles and Towing
Attachments:
Articulation Hitch
BODY, CAB, HOOD,

AND HULL
Body, Cab, Hood, and
Hull Assemblies:
Hood Assemblies
ROPS/Cab Assembly
(Types I & II)
ROPS/Cab Assembly
(CCE)
Seat Assembly
Seat Belt
MAINTENANCE
FUNCTION
UNIT
C
(5)
(6)
SUSTAINMENT
DS
GS
DEPOT
TOOLS AND
EQUIPMENT REMARKS
REF CODE
CODE
Repair
3.0
74,89
Repair
3.0
74,89
89
2,3,4,5,
46,59,60,65,
68,74,89,91,
96
Service
Repair
Replace
Replace
Repair
Replace
Repair
Replace
Inspect
Replace
Replace
Toolboxes
BUMPERS,
GUARDS, AND
MARINE FENDERS
Bumper
Replace
BODY, CHASSIS
AND HULL
ACCESSORY ITEMS
Accessory Items:
Windshield Wiper
Replace
Assembly
Repair
0.2
0.5
2.0
1.0
4.0
2.0
0.8
75,78,89
75,78,89
75,78,89
75,78,89
75,78,89
89
0.3
0.3
89
89
8.0
4.0
0.2
1.0
1.0
2.0
0348 00-8
78,89
75,89
75,89
TM 5-3805-261-23-2
0348 00
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
FIELD
GROUP
NUMBER
22
24
2401
COMPONENT/
ASSEMBLY
MAINTENANCE
FUNCTION
UNIT
C
BODY, CHASSIS
AND HULL
ACCESSORY ITEMS
- Continued
Defroster Fans
Replace
Repair
Heater Assembly
Replace
Repair
Data Plates and Decals Replace
HYDRAULIC AND
FLUID SYSTEMS
Hydraulic Pump
Test
Assembly:
Service
Replace
Repair
2403
2406
2407
2408
47
(6)
SUSTAINMENT
DS
GS
DEPOT
1.0
1.0
1.5
1.5
0.2
TOOLS AND
EQUIPMENT REMARKS
REF CODE
CODE
89
89
89
89
30,89
0.4
0.3
2.5
3.0
Circle Drive Motor
2402
Replace
Repair
Pilot Check and
Adjust
Pressure Control Valve Replace
Assemblies
Repair
Hydraulic Control
Adjust
Levers and Linkage
Replace
Strainers, Filters, Lines, Inspect
and Fittings, Etc.:
Replace
Oil Cooler Assembly Replace
Hydraulic Cylinders
Replace
Repair
Hydraulic Tank and
Inspect
Mounting Assembly
Service
Replace
Repair
GAUGES (NONELECTRICAL)
Gauges: Pressure,
Replace
Temperature, and
Articulation Indicator
(5)
1.0
3.0
1.0
3.0
2.5
1.5
2.0
89
74,78,89,96
13,43,52,69,74,
89,94,96
89
74,89,96
74,89
74,89,94,96
89
89
0.2
2.0
2.0
1.5
3.0
74,89
74,89
74,78,89,100
74,89,101
2.0
2.0
75,89
74,78,89,96
74,89,96
0.2
0.2
0.5
0348 00-9
89
TM 5-3805-261-23-2
0348 00
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
FIELD
GROUP
NUMBER
74
7435
7436
COMPONENT/
ASSEMBLY
MAINTENANCE
FUNCTION
CRANES, SHOVELS,
AND
EARTHMOVING
EQUIPMENT
COMPONENTS
Moldboard Assembly: Inspect
Service
Replace
Repair
Cutting Edges
Inspect
Replace
End Bits
Inspect
Replace
Moldboard Lift Arms Service
and Pivot Assembly
Replace
UNIT
C
Circle and Drawbar

Assembly:
Drawbar Assembly
Service
Replace
Repair
Circle Turn Assembly Inspect
Service
Replace
7439
7440
Centershift Lock
Assembly
Scarifier Assembly
Repair
Replace
Repair
Inspect
Service
Replace
Repair
(6)
SUSTAINMENT
DS
GS
DEPOT
TOOLS AND
EQUIPMENT REMARKS
REF CODE
CODE
0.2
0.3
3.0
A
2.0
17,78,89
74,89
0.1
2.0
75,89
1.5
0.3
75,89
0.1
0.3
A
2.4
Repair
7438
(5)
3.0
4,6,22,23,
48,61,65,72,
74,78,89,92
10,47,60,74,
86,89,91
0.3
A
2.4
3.4
74,78,89,101
74,89
0.1
0.3
2.0
3.0
1.0
1.5
75,89
74,77,78,84,89,
101
74,78,89,100
89
89
0.1
0.3
A
2.0
3.0
0348 00-10
74,78,89
74,78,89
TM 5-3805-261-23-2
0348 00
Table 2. Tools and Test Equipment Requirements for the 130G Series Grader .
(1)
(2)
(3)
(5)
(4)
ITEM
NO.
MAINTENANCE
LEVEL
NATIONAL
STOCK NUMBER
PART NUMBER/
CAGEC
Adapter, Bearing Remover
5120-01-300-4502
1P1832 (11083)
Adapter, Mechanical Puller
5120-00-357-5181
8B7555 (11083)
5120-01-286-8431
1P1838 (11083)
5120-01-286-8432
1P1837 (11083)
5120-01-288-2717
5P4184 (11083)
5120-01-286-8435
1P1835 (11083)
5120-00-316-9172
8B7556 (11083)
Adapter, Nozzle
5120-01-345-4526
FT1533 (11083)
Adapter, Puller
5120-01-286-8433
1P1833 (11083)
10
Adapter, Puller
5120-01-286-8434
1P1834 (11083)
11
Adapter, Puller
5120-01-295-3618
5F7340 (11083)
12
Analyzer Set, Engine
4910-00-124-2554
2389409 (16331)
13
Block
FT1017 (11083)
14
Bolt, Machine
0S1602 (11083)
15
Bracket, Lifting
5340-01-336-2459
FT0120 (11083)
16
Bracket, Link
5120-01-451-1401
1387575 (11083)
17
Bracket, Link
5340-01-476-1734
1387574 (11083)
18
Bracket, Link
4940-01-268-2201
1387573 (11083)
19
Bushing Driver, Valve
5120-01-030-1625
7S8858 (11083)
20
Compressor, Valve Spring
5120-00-314-6138
5S1330 (11083)
21
Driver Bit, T-15 TORX
22
Driver Set, Bushing
5120-01-030-1626
1P0510 (11083)
23
Expander Assembly
5120-00-489-8167
4S9181 (11083)
24
Extractor, Tool
2520-01-201-4146
5R7047 (11083)
25
Extractor, Valve Group
4910-01-296-3862
1667441 (11083)
26
Gage, Profile
5220-01-296-4296
6V7058 (11083)
27
Gage, Profile
5220-01-296-4297
6V7068 (11083)
ITEM NAME
0348 00-11
1943532 (11083)
TM 5-3805-261-23-2
0348 00
Table 2. Tools and Test Equipment Requirements for the 130G Series Grader - Continued.
(1)
(2)
(3)
(5)
(4)
ITEM
NO.
MAINTENANCE
LEVEL
28
29
NATIONAL
STOCK NUMBER
PART NUMBER/
CAGEC
Gear, Engine Turning
4910-01-137-0662
5P7305 & 5P7306

(11083)
Guard, Safety, Tire Inflation
4910-00-025-0623
64E33077 (80049)
30
Heater, Gun-Type, Electric
4940-01-028-7493
EP-5UL (59164)
31
Housing, Gear Shaft
5120-01-119-1747
5P7306 (11083)
32
Indicator, Dial
5210-01-354-9255
6V3075 (11083)
33
Inserter, Seal
5120-01-122-6012
1U8698 (11083)
34
Inserter, Seal
5120-01-288-2777
5P2980 (11083)
35
Installer Tool, Seal
5H4845 (11083)
36
Jack Group
5P2968 (11083)
37
Jack, Dolly Type, Hydraulic: 10-ton

capacity
38
Leg
7S7786 (11083)
39
Leg
4S5415 (11083)
40
Leg, Mechanical Puller
5120-01-345-5328
1H3109 (11083)
41
Leg, Puller
5120-01-275-9480
8B7549 (11083)
42
Leveler, Load
3950-01-263-9513
6V3145 (11083)
43
Maintenance Fixture, Automotive
4910-01-286-8364
2P5573 (11083)
44
Nut
1P544 (11083)
45
Nut
5P0637 (11083)
46
Nut, Plain, Hexagon
5310-00-404-3787
7H7539 (11083)
47
Nut, Fastener
5310-01-483-6594
1P-0544 (11083)
48
Nut
49
Nut, Plain, Hexagon
5310-00-656-6973
5F7351 (11083)
50
Nut, Plain, Round
5310-01-480-6692
1P-0543 (11083)
51
Pin
5315-01-270-2832
8S7615 (11083)
52
Plate, Protective
5120-01-288-242
5P975 (11083)
53
Plate, Step
8B7560 (11083)
54
Puller
FT0530 (11083)
55
Puller Attachment, Bearing
ITEM NAME
4910-00-289-7233
93660 (36251)
5S7351 (11083)
0348 00-12
5120-00-288-6756
8B7551 (11083)
TM 5-3805-261-23-2
0348 00
(1)
(2)
(3)
(5)
(4)
ITEM
NO.
MAINTENANCE
LEVEL
56
57
NATIONAL
STOCK NUMBER
PART NUMBER/
CAGEC
Puller Attachment, Cup
5120-00-293-1430
8B7554 (11083)
Puller Attachment, Mechanical
5120-00-288-6756
8B7551 (11083)
58
Puller Group, Nozzle
2910-01-250-1608
6V6980 (11083)
59
Puller, Hydraulic
5130-01-294-0717
6V3170 (11083)
60
Puller, Hydraulic
5130-01-296-4277
6V3175 (11083)
61
Puller, Hydraulic
5130-00-363-6680
6V3160 (11083)
62
Puller, Mechanical
5120-00-633-5085
GGG-P-781 (11083)
63
Puller, Mechanical
5120-00-633-5074
939 (45225)
64
Puller, Mechanical
5120-00-600-3306
1P2322 (11083)
65
Pump, Hydraulic Ram, Hand Driven
4320-00-374-1403
4C4865 (11083)
66
Ratchet Assembly
5120-01-275-2286
8S9906 (11083)
67
Removing Tool, Scarifier Tooth
3805-00-423-9746
6B3260 (11083)
68
Ring Installer
2P5498 (11083)
69
Rod, Guide
FT1016 (11083)
70
Saddle
71
Screw
8S6586 (11083)
72
Screw
8S6585 (11083)
73
Screw, Machine
5305-01-295-3554
5F7366 (11083)
74
Shop Equipment, Automotive

Maintenance and Repair: Field
Maintenance, Basic, Less Power
4910-00-754-0705
SC4910-95CLA31
(19204) (LIN:
W32593)
75

Maintenance and Repair: Organizational
Maintenance, Common No. 1, Less Power
4910-00-754-0654
SC 4910-95CLA74
(19204) (LIN:
W32593)
76

Maintenance and Repair: Organizational
Maintenance, Common No. 2, Less Power
4910-00-754-0650
SC4910-95CLA72
(19204)
77
Shop Equipment, Contact Maintenance:

Truck Mounted
4940-00-294-9518
MILS45854 (81349)
78
Sling
2835-01-078-2081
4-8FTX2IN (91796)
79
Socket, Spanner
5120-01-288-2545
5P4204 (11083)
ITEM NAME
2510-01-264-8424
0348 00-13
8S8048 (11083)
TM 5-3805-261-23-2
0348 00
(1)
(2)
(3)
(5)
(4)
ITEM
NO.
MAINTENANCE
LEVEL
80
Spacer
81
Spacer, Puller Screw
5120-00-423-8162
0T0774 (11083)
82
Spacer, Sleeve
5365-01-288-2658
5P4197 (11083)
83
Stand, Lifting and B
5120-01-134-8085
4C6486 (11083)
84
Stand, Maintenance, Automotive Axle:

24,000 lb capacity,
height range 1929-1/2 in.
4910-01-480-0147
1778A (45225)
85
Stand, Maintenance, Automotive Engine
4910-01-117-4344
1750A (45225)
86
Stud, Plain
5307-01-485-7432
4C-9634 (11083)
87
Tester Group, Nozzle
4320-01-263-9716
5P4150 (11083)
88
Tester, Spring Resiliency
6635-01-124-1771
8S2263 (11083)
89
Tool Kit, General Mechanics:

Automotive
5180-01-454-3787
12B470000 (59678)
90
Tool, Special
4910-01-265-0428
8S7611 (11083)
91
Washer, Flat
5310-01-526-7006
3H-0467 (11083)
92
Washer
5310-01-485-7439
5F7353 (11083)
93
Wrench, Ratchet
5120-01-350-5274
8H684 (11083)
94
Wrench, Torque: 3/8 in. drive, 0-150 lb-in.
5120-00-230-6380
TQ12B (55719)
95
5120-00-853-4538
96
Wrench, Torque, 3/8 in. drive, 0-75 lb-ft
5120-00-554-7292
97
Wrench, Torque, 3/8 in. drive, 5-75 lb-ft
5120-01-355-1734
98
5120-00-247-2563
99
Wrench, Torque: 1/2 in. drive, 50-250 lb-ft
5120-01-399-5604
100
5120-01-042-0982
101
5120-01-113-9564
7379 (45225)
102
Wrench, Torque: 3/4 in. drive, 120-600 lbft
5120-01-399-5605
TWZ600 (76377)
ITEM NAME
NATIONAL
STOCK NUMBER
PART NUMBER/
CAGEC
L-1774 (11083)
0348 00-14
GGG-W-00686
(81348)
TVW250 (76377)
TM 5-3805-261-23-2
0348 00
Table 3. Remarks for the 130G Series Grader.

(1)
(2)
REFERENCE
CODE
REMARKS
A
B
C
D
E
F
G
H
I
J
Preventive Maintenance Checks and Services (PMCS)

Limited Field Repair Authorized (Seals, Gaskets, Bearings, Plugs, and Cylinder Head)
Limited Field Repair Authorized (Seals, Gaskets, Injectors, Springs, and Valves)
Limited Field Repair Authorized (Replacement of Broken or Missing Parts and/or Minor Welding)
Limited Field Repair Authorized (Seals, Gaskets, and Bearings)
Limited Field Repair Authorized (Seals, Gaskets, Bearings, and Brushes)
Limited Field Repair Authorized (Seals, Gaskets, Bearings, Brushes, and Starter Gear)
Limited Field Repair Authorized (Seals, Gaskets, Wipers, and Rings)
Limited Field Repair Authorized (Seals, Gaskets, and Missing/Broken Parts)
Refer to TM 9-2610-200-14
END OF WORK PACKAGE
0348 00-15/(-16 Blank)
TM 5-3805-261-23-2
EXPENDABLE AND DURABLE ITEMS LIST
0349 00
SCOPE
This work package lists expendable and durable items you will need to maintain the 130G Grader. This listing is for
informational purposes only and is not authority to requisition the listed items. These items are authorized to you by CTA 50970, Expendable/Durable Items (Except Medical, Class V Repair Parts, and Heraldic Items), or CTA 8-100, Army Medical
Department Expendable/Durable Items.
EXPLANATION OF COLUMNS
1.
Column (1) - Item Number. This number is assigned to the entry in the listing and is referenced in the narrative instructions to identify the item [e.g., Use antifreeze (Item 5, WP 0349 00)].
2.
Column (2) - Level. This column identifies the lowest level of maintenance that requires the listed item.
C - Operator/Crew
O - Unit Maintenance
F - Direct Support Maintenance
3.
Column (3) - National Stock Number. This is the National Stock Number assigned to the item which you can use to
requisition it.
4.
Column (4) - Description, CAGEC, and Part Number. This provides the other information you need to identify the
item.
5.
Column (5) - Unit of Measure (U/M). This column shows the physical measurement or count of an item, such as gallon, dozen, gross, etc.
0349 00-1
TM 5-3805-261-23-2
EXPENDABLE AND DURABLE ITEMS LIST - CONTINUED
0349 00
(1)
(2)
(3)
(4)
(5)
ITEM
NUMBER
LEVEL
NATIONAL
STOCK NUMBER
DESCRIPTION, CAGEC,
AND PART NUMBER
U/M
8040-01-023-4173
8040-01-250-3969
5340-00-450-5718
ADHESIVE: Type 2
(05972) 242
BT
1 Gallon Can
55 Gallon Drum
CN
DR
1 Pound Tube or Can

CAP SET, PROTECTIVE, DUST AND
MOISTURE
(19207) 10935405
TU or CN
EA
CLEANING COMPOUND: Solvent, Type III

(81349) MIL-PRF-680
6850-01-474-2318
6850-01-474-2320
6850-01-474-2321
1 Pint Can
ANTISEIZE COMPOUND
(05972) 76764
8030-00-251-3980
TU
CN
ANTIFREEZE: Permanent, Ethylene Glycol,

Inhibited
(58536) AA52624-1-A
6850-01-441-3218
6850-01-441-3223
4 Ounce Tube
1/2 Pint Can
ADHESIVE: PVC
(25472) A541B
8040-00-573-1502
4
PT
ADHESIVE
(81348) MMM-A-1617
8040-00-262-9025
8040-00-262-9026
ADHESIVE
(1A9T3) EC-1300
1 Gallon Can
5 Gallon Can
55 Gallon Drum
CN
CN
DR
CLOTH: Abrasive, Emery, Fine

(80204) ANSI B74.18
5350-00-584-4654
50 Sheet Package
10
COMPOUND, RETAINING
MIL-R-46082A
11
DETERGENT: General Purpose, Liquid

(83421) 7930-00-282-9699
7930-00-282-9699
1 Gallon Can
0349 00-2
PG
CN
TM 5-3805-261-23-2
0349 00
(1)
(2)
(3)
(4)
(5)
ITEM
NUMBER
LEVEL
NATIONAL
STOCK NUMBER
DESCRIPTION, CAGEC,
AND PART NUMBER
U/M
12
FLUX: Soldering
(58536) A-A-51145TY FORM A
3439-00-255-9935
13
18
19
Bulk
5 Gallon Can
55 Gallon Drum
GL
CN
DR
Bulk
GL
GASKET CEMENT
(11083) 5H2471
8040-01-038-5043
17
GL
CN
DR
FUEL, TURBINE: Aviation

(81349) MILT83133 GR JP8
9130-01-031-5816
16
Bulk
5 Gallon Can
55 Gallon Drum
FUEL: Diesel, DF-2 Grade
(81346) ASTM D 975
9140-00-286-52
9140-00-286-52
9140-00-286-52
15
CN
FUEL: Diesel, DF-1 Grade, Winter

(81346) ASTM D 975
9140-00-286-5286
9140-00-286-5287
9140-00-286-5288
14
1 Pound Can
8 Ounce Can
CN
GREASE: Automotive and Artillery, GAA

9150-01-197-7688
(81349) M-10924-A
2-1/4 Ounce Tube
TU
9150-01-197-7690
(81349) M-10924-C
1-3/4 Pound Can (81349)
CN
9150-01-197-7692
(81349) M-10924-E
35 Pound Pail
CN
9150-01-197-7693
(81349) M-10924-B
14 Ounce Cartridge
CA
9150-01-361-8919
GREASE, ELECTRICALLY CONDUCTIVE

(53711) 5190179
OZ
INSULATING SLEEVING, ELECTRICAL

(11530) 08-196485-06
5970-00-815-1295
250 Foot Spool
0349 00-3
FT
TM 5-3805-261-23-2
0349 00
(1)
(2)
(3)
(4)
(5)
ITEM
NUMBER
LEVEL
NATIONAL
STOCK NUMBER
DESCRIPTION, CAGEC,
AND PART NUMBER
U/M
20
INSULATING VARNISH, ELECTRICAL

(75037) 1602
5970-00-476-6717
21
13 Ounce Aerosol Can

LUBRICANT: Rubber
(11083) 5P-3975
1 Gallon Can
22
23
LUBRICATING OIL, GEAR: GO 75

(81349) MIL-PRF-2105
29
CN
CN
DR
1 Pound Can
CN
1 Quart Can
5 Gallon Can
55 Gallon Drum
CN
CN
DR
OIL, LUBRICATING: OE/HDO-10

(81349) MIL-PRF-2104
9150-00-189-6727
9150-00-186-6668
9150-00-191-2772
28
1 Quart Can
5 Gallon Can
55 Gallon Drum
OIL, LUBRICATING: OEA, Arctic

(81349) MIL-L-46167
9150-00-402-4478
9150-00-402-2372
9150-00-491-7197
27
CN
CN
LUBRICATING OIL: Molybdenum Disulfide,

Silicone
(81349) DOD-L-25681
9150-00-543-7220
26
1 Quart Can
5 Gallon Can
LUBRICATING OIL, GEAR: GO 80/90
(81349) MIL-PRF-2105
9150-01-035-5392
9150-00-001-9395
9150-01-035-5394
25
CN
LUBRICANT, THREAD
(11083) 2P2506
9150-01-035-5390
9150-01-035-5391
24
CN
9150-00-247-0481
C
1 Quart Can
5 Gallon Can
55 Gallon Drum
OIL, LUBRICATING: OE/HDO-10/30
(2R128) BRAYCO413J
CN
CN
DR
QT
OIL, LUBRICATING: OE/HDO-30

(81349) MIL-PRF-2104
9150-00-186-6681
9150-00-188-9858
1 Quart Can
5 Gallon Can
0349 00-4
CN
CN
TM 5-3805-261-23-2
0349 00
(1)
(2)
(3)
(4)
(5)
ITEM
NUMBER
LEVEL
NATIONAL
STOCK NUMBER
DESCRIPTION, CAGEC,
AND PART NUMBER
U/M
30
OIL, LUBRICATING: OE/HDO-15/40

(81349) MIL-PRF-2104
9150-01-152-4117
9150-01-152-4118
9150-01-152-4119
1 Quart Can
5 Gallon Can
55 Gallon Drum
31
5350-00-619-9167
PAPER, ABRASIVE: 80 Grit,

9x11 Sheets
(80204) ANSI B74.18
32
9150-00-905-1387
PENETRATING OIL: AEROKROIL

(13868)
10 Ounce Can, Pressurized
33
CN
7.5 Pound Can
CN
PIGMENT, PAINT PRODUCTS: Prussian Blue

(58536) AA3108-2A-001Q
8010-00-664-1414
35
1 Quart Can
CN
RAG, WIPING
(80244) 7920-00-205-1711
7290-00-205-1711
50 Pound Bale
36
ROPE
37
SANDPAPER: No. 00
38
BL
SEALING COMPOUND
(05972) 26241
8030-01-142-3131
39
O, F
40
41
250 CC Bottle
BT
SEALING COMPOUND
MIL-S-22473
6920-01-239-1562
SEALANT, THREAD: 11784488

(19200)
TV
SILICONE COMPOUND
(19207) 12273204
6850-00-927-9461
42
PG
PETROLATUM, TECHNICAL
(81348) VV-P-236
9150-00-250-0933
34
CN
CN
DR
5 Ounce Tube
TU
SOLDER: Lead-Tin Alloy, Rosin Core

(81346) SN60WRP2 0.032 1LB
3439-00-555-4629
1 Pound Spool
0349 00-5
LB
TM 5-3805-261-23-2
0349 00
(1)
(2)
(3)
(4)
(5)
ITEM
NUMBER
LEVEL
NATIONAL
STOCK NUMBER
DESCRIPTION, CAGEC,
AND PART NUMBER
U/M
43
STRAP, TIEDOWN, ELECTRICAL

COMPONENTS
5975-00-903-2284
4 Inch Length, Black, Package of 100

(96906) MS3367-4-0
HD
5975-00-984-6582
6 Inch Length, Black, Package of 100

(96906) MS3367-1-0
HD
5975-00-935-5946
13.35 Inch Minimum Length, Brown

(96906) MS3367-2-1
EA
44
TAG, MARKER
(64067) 9905-00-537-8954
9905-00-537-8954
45
Bundle of 50
BD
TAPE, DUCT
2 Inches Wide
(39482) 1791K70
5640-00-103-2254
46
60 Yard Roll
RL
WIRE, NONELECTRICAL
(81346) ASTM A641
9905-00-596-0191
283 Foot Coil
END OF WORK PACKAGE

0349 00-6
CL
TM 5-3805-261-23-2
ILLUSTRATED LIST OF MANUFACTURED ITEMS
0350 00
INTRODUCTION
1.
This work package includes complete instructions for making items authorized to be manufactured by maintenance personnel.
2.
An index, in alphabetical order by nomenclature, is provided for cross-referencing the item to be manufactured to the
Figure number and page number where manufacturing instructions are located. Refer to Table 1 below.
3.
Manufacture from steel or aluminum stock to specifications on the illustrations.
4.
All dimensions on illustrations are in standard units.

Table 1. Manufactured Items Cross-Reference Index.
NOMENCLATURE
FIGURE NUMBER
PAGE NUMBER
Adapter Tool
Figure 1
0325 00-1
Interference Block
Figure 2
0325 00-2
MANUFACTURING INSTRUCTIONS
3/16 IN.
1-1/2 IN.
3/8 IN.
3/8 IN.
397-883
Figure 1. Adapter Tool.
0350 00-1
TM 5-3805-261-23-2
ILLUSTRATED LIST OF MANUFACTURED ITEMS - CONTINUED
0350 00
MANUFACTURING INSTRUCTIONS - CONTINUED
2-1/2 IN.
3/4 IN.
3/4 IN.
1/4 IN.
1/4 IN.
1 IN.
1 IN.
1-1/4 IN.
1-1/4 IN.
63/64 IN.
1/2 IN.
397-4359
Figure 2. Interference Block.

END OF WORK PACKAGE
0350 00-2
TM 5-3805-261-23-2
TORQUE LIMITS
0351 00
SCOPE
This work package lists standard torque values and provides general information for applying torque. Special torque values and tightening sequences are indicated in the maintenance procedures for applicable components.
GENERAL
1.
Always use torque values listed in Tables 1 and 2 when a maintenance procedure does not give a specific torque value.
a.
Table 1 provides torque limits for SAE standard fasteners.
b.
Table 2 provides torque limits for metric fasteners.
2.
Unless otherwise indicated, standard torque tolerance shall be 10%.
3.
Torque values listed are based on clean, dry threads. Reduce torque by 10% when engine oil is used as a lubricant.
Reduce torque by 20% if new plated capscrews are used.
4.
If the maintenance procedures do not specify a tightening order, use the following guides:
a.
Unless otherwise specified, lubricate threads of fasteners with oil (OE/HDO-10 or OEA-30).
b.
When tightening fasteners above 30 lb-ft (41 Nm), use the torque pattern but only tighten to 70% of final value
(multiply final value by 0.7). Repeat pattern until final value is reached.
c.
Tighten circular patterns using circular torque pattern and tighten straight patterns using straight torque pattern.
5
12
10
4
3
11
9
6
CIRCLULAR TORQUE PATTERN
5 3 1 2 4 6
STRAIGHT TORQUE PATTERN
0351 00-1
TM 5-3805-261-23-2
TORQUE LIMITS - CONTINUED
0351 00
CAUTION
If replacement capscrews are of higher grade than originally supplied, use torque specifications for the original. This will prevent equipment damage due to overtorquing.
Table 1. Torque Limits - SAE Standard Fasteners.
Current Usage
Much Used
Much Used
Used at Times
Used at Times
QUALITY OF
MATERIAL
INDETERMINATE
MINIMUM
COMMERCIAL
MEDIUM
COMMERCIAL
BEST
COMMERCIAL
SAE Grade Number
1 or 2
6 or 7
Cap Screw Head

Markings
Manufacturers
marks may vary
These are all
SAE Grade 5
(3 line)
CAP SCREW BODY

SIZE IN. - THREAD
TORQUE
LB-FT (NM)
TORQUE
LB-FT (NM)
TORQUE
LB-FT (NM)
TORQUE
LB-FT (NM)
1/4
20
28
5
6
(7)
(8)
8
10
(11)
(14)
10
(14)
12
14
(16)
(19)
5/16
18
24
11
13
(15)
(18)
17
19
(23)
(26)
19
(26)
24
27
(33)
(37)
3/8
16
24
18
20
(24)
(27)
31
35
(42)
(47)
34
(46)
44
49
(60)
(66)
7/16
14
20
28
30
(38)
(41)
49
55
(66)
(75)
55
(75)
70
78
(95)
(106)
1/2
13
20
39
41
(53)
(56)
75
85
(102)
(115)
85
(115)
105
120
(142)
(163)
9/16
12
18
51
55
(69)
(75)
110
120
(149)
(163)
120
(163)
155
170
(210)
(231)
5/8
11
18
83
95
(113)
(129)
150
170
(203)
(231)
167
(226)
210
240
(285)
(325)
3/4
10
16
105
115
(142)
(156)
270
295
(366)
(400)
280
(380)
375
420
(508)
(569)
7/8
9
14
160
175
(217)
(237)
395
435
(536)
(590)
440
(597)
605
675
(820)
(915)
8
14
235
250
(319)
(339)
590
660
(800)
(895)
660
(895)
910
990
(1234)
(1342)
0351 00-2
TM 5-3805-261-23-2
TORQUE LIMITS - CONTINUED
0351 00
Table 2. Torque Limits - Metric Fasteners.
Torque values for metric thread fasteners with lubricated* or plated threads
Thread
Diameter-Pitch
Class 8.8 Bolt
Class 8 Nut
Class 10.9 Bolt
Class 10 Nut
Torque: lb-ft (Nm)
Torque: lb-ft (Nm)
5 (7)
7 (9)
12 (16)
17 (23)
13 (18)
18 (24)
M10
M10 x 1.25
24 (33)
34 (46)
27 (37)
38 (52)
M12
M12 x 1.5
42 (57)
60 (81)
43 (58)
62 (84)
M14
M14 x 1.5
66 (89)
95 (129)
72 (98)
103 (140)
M16
M16 x 1.5
103 (140)
148 (201)
110 (149)
157 (213)
M18
M18 x 1.5
147 (199)
203 (275)
165 (224)
229 (310)
M20
M20 x 1.5
208 (282)
288 (390)
213 (313)
320 (434)
M22
M22 x 1.5
283 (384)
392 (531)
315 (427)
431 (584)
M24
M24 x 2
360 (488)
498 (675)
392 (531)
542 (735)
M27
M27 x 2
527 (715)
729 (988)
569 (771)
788 (1068)
M30
M30 x 2
715 (969)
990 (1342)
792 (1074)
1096 (1486)
M6
M8
M8 x 1
* All plated and unplated fasteners should be coated with oil before installation.
Use these torque values if either the bolt or nut is lubricated or plated (zinc-phosphate conversion-coated,
cadmium-plated, or waxed).
END OF WORK PACKAGE
0351 00-3/(-4 Blank)
TM 5-3805-261-23-2
SCHEMATIC DIAGRAMS
0352 00
INTRODUCTION
1.
This work package contains schematic diagrams for the 130G Series Grader.
2.
The following schematic diagrams are included in this work package:

Figure 1. 130GNS and 130GNSCE Electrical Schematic
Figure 2. 130GS and 130GSCE Electrical Schematic
Figure 3. Fuse and Switch Logic Schematic
Figure 4. Hydraulic System Schematic
Figure 5. Steering System Schematic
Figure 6. 130G, 130GNS, and 130GNSCE Air Brake System Schematic
Figure 7. 130GS and 130GSCE Air Brake System Schematic
Figure 8. Supplemental Steering Electrical Schematic
Figure 9. Supplemental Steering Hydraulic Schematic (Non-actuated)
Figure 10. Supplemental Steering Hydraulic Schematic (Actuated)
Figure 11. Engine Charging System Schematic
Figure 12. Cooling System Schematic
Figure 13. Fuel System Schematic
Figure 14. Lubrication System Schematic
Figure 15. Transmission Hydraulic Schematic
Figure 16. Transmission Control Valves Schematic
Figure 17. 130 G Electrical Schematic
0352 00-1
TM 5-3805-261-23-2
SCHEMATIC DIAGRAMS - CONTINUED
0352 00
TO SHEET 3
TO SHEET 2
397-4365
Figure 1. 130GNS and 130GNSCE Electrical Schematic (Sheet 1 of 6).

0352 00-2
TM 5-3805-261-23-2
0352 00
TO SHEET 4
TO SHEET 1
397-4366

0352 00-3
TM 5-3805-261-23-2
0352 00
TO SHEET 5
TO SHEET 1
TO SHEET 4
397-4367

0352 00-4
TM 5-3805-261-23-2
0352 00
TO SHEET 2
TO SHEET 3
397-4368

0352 00-5
TM 5-3805-261-23-2
0352 00
TO SHEET 3
TO SHEET 6
397-4369

0352 00-6
TM 5-3805-261-23-2
0352 00
TO SHEET 5
397-4370

0352 00-7
TM 5-3805-261-23-2
0352 00
TO SHEET 3
TO SHEET 2
397-4371
Figure 2. 130GS and 130GSCE Electrical Schematic (Sheet 1 of 6).

0352 00-8
TM 5-3805-261-23-2
0352 00
TO SHEET 4
TO SHEET 1
397-4372

0352 00-9
TM 5-3805-261-23-2
0352 00
TO SHEET 1
TO SHEET 5
TO SHEET 4
397-4373

0352 00-10
TM 5-3805-261-23-2
0352 00
TO SHEET 2
TO SHEET 6
TO SHEET 3
397-4374

0352 00-11
TM 5-3805-261-23-2
0352 00
TO SHEET 3
TO SHEET 6
397-4375

0352 00-12
TM 5-3805-261-23-2
0352 00
TO SHEET 4
TO SHEET 5
397-4376

0352 00-13
TM 5-3805-261-23-2
0352 00
*130G Only
397-888
Figure 3. Fuse and Switch Logic Schematic (Sheet 1 of 2).

0352 00-14
TM 5-3805-261-23-2
0352 00
*130G Only
397-889
Figure 3. Fuse and Switch Logic Schematic (Sheet 2 of 2).

0352 00-15
TM 5-3805-261-23-2
0352 00
LEGEND
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
26.
27.
28.
31.
32.
33.
34.
35.
37.
38.
39.
41.
45.
46.
47.
48.
49.
Cylinder for leaning wheel

Cylinder for center shift
Cylinders for blade lift
Cylinder for blade side shift
Cylinder for blade tip
Cylinders for articulation
Cylinder for steering (L.H.)
Cylinder for steering (R.H.)
Metering pump for steering
Combination valve
Relief and reducing valve
Unloading valve
Relief valve for cooler
Implement pump
Variable displacement pump
Pump for cooling
Cooler
Control valve group
Control valve group
Valve for articulation
Valve for center shift
Valve for wheel lean
Hydraulic pump relief valve
Valve for scarifier
Valve for blade tip
Valve for circle drive
Valve for blade side shift
Lock check valve
Lock check valve
Lock check valve
Relief valves for steering
Hydraulic motor for circle drive
Hydraulic tank
Filters
Swivel
Lock check valve
Cylinder for scarifier
Lock check valve (with relief)
Pilot valve (solenoid operated)
Lock check valves (pilot operated)
Supplemental steering
0352 00-16
TM 5-3805-261-23-2
0352 00
38
38
37
14
14 15
17
16
6 13
32
397-890
Figure 4. Hydraulic System Schematic (Sheet 1 of 5).

0352 00-17
TM 5-3805-261-23-2
0352 00
*
*
9
10
12
10
12
23
*130G ONLY
397-891

0352 00-18
TM 5-3805-261-23-2
0352 00
*
*
34
*
*
*
*
23
46
28
27
19
26
46
20
21
22
23
24
*130G ONLY
397-892

0352 00-19
TM 5-3805-261-23-2
0352 00
*
*
*
*
*
*
31
*
*
3
33
*
*
39
35
4
32
32
*130G ONLY
397-893

0352 00-20
TM 5-3805-261-23-2
0352 00
*
*
*
*
47
48
*
*
1
31
41
45
*130G ONLY
397-894

0352 00-21
TM 5-3805-261-23-2
0352 00
LEGEND
1.
Steering wheel
2.
Crossover relief valve
3.
Crossover relief valve
4.
Plug
5.
Oil return line to tank
6.
Steering metering pump
7.
Plug
8.
Shims
9.
Shims
10.
Oil supply line from pump
11.
Left steering cylinder
12.
Right steering cylinder
13.
Oil return line to tank
14.
Shims
15.
Steering pressure reducing valve
16.
Plug
0352 00-22
TM 5-3805-261-23-2
0352 00
7
9
8
5
10
11
13
12
14 15 16
397-895
Figure 5. Steering System Schematic.
0352 00-23
TM 5-3805-261-23-2
0352 00
LEGEND
A.
System pressure
System pressure from left section of air tank
C.
System pressure from right section of air tank
1.
Service brakes (four)
2.
Air compressor
3.
Air compressor governor
4.
Safety relief valve
5.
One-way check valve
6.
Air tank with two sections
7.
Quick release valve
8.
Rotochamber for parking brake
9.
Safety relief valve
10.
One-way check valve
11.
Air pressure gauges
12.
Low air pressure sending units (to EMS)
13.
Control valve for service brakes
14.
Blackout stoplight switch
15.
Stoplight switch
16.
Onew-way check valve
17.
Control valve for parking brake
18.
Center shift control valve
19.
Center shift lock pin
0352 00-24
TM 5-3805-261-23-2
0352 00
1
2
3
5
4
14
15
7
13
8
10
11
12
16
18
19
17
397-896
Figure 6. 130G, 130GNS, and 130GNSCE Air Brake System Schematic.

0352 00-25
TM 5-3805-261-23-2
0352 00
LEGEND
1.
Remote control panel
2.
Control valve (4-way)
3.
Solenoid (24V, N.O.)
4.
Check valve
5.
Check valve
6.
Brake (service)
7.
Brake (service)
8.
Dual brake control valve (service) (in cab)
9.
Relay valve
10.
Relay valve
11.
Quick release valve
12.
Actuator (parking brake)
13.
Solenoid (24V, N.C.)
14.
Pressure switch (6-8 psi, N.C.)
15.
Parking brake valve (in cab)
16.
Air reservoir (service)
17.
Air gauges
18.
Air compressor governor
19.
Air compressor
20.
Disconnect plate
21.
Pressure switch (60 psi, N.C.)
22.
Parking brake valve
23.
Pressure regulator
0352 00-26
TM 5-3805-261-23-2
0352 00
3
23
4
6
22
21
20
17
18
19
9
8
10
17
16
11
12
15
13
14
397-4377
Figure 7. 130GS and 130GSCE Air Brake System Schematic.

0352 00-27
TM 5-3805-261-23-2
0352 00
397-897
Figure 8. Supplemental Steering Electrical Schematic.

0352 00-28
TM 5-3805-261-23-2
0352 00
4
13
6
7
8
12
9
13
11
13
10
14
15
16
397-898
LEGEND
1.
Cooler for hydraulic oil
9.
Metering valve for steering
2.
By-pass valve for oil cooler
10.
Flow to relief valves and steering cylinder
3.
Hydraulic tank
11.
Combination valve
4.
Relief valve (supplemental steering)
12.
Implement pump
5.
Pump for oil to oil cooler
13.
Check valves
6.
Electric motor
14.
Pressure sensing switch
7.
Steering wheel
15.
Dump valve switch
8.
Supplemental steering pump
16.
Dump valve
Figure 9. Supplemental Steering Hydraulic Schematic (Non-actuated).

0352 00-29
TM 5-3805-261-23-2
0352 00
LEGEND
1.
Cooler for hydraulic oil
2.
By-pass valve for oil cooler
3.
Hydraulic tank
4.
Relief valve (supplemental steering)
5.
Pump for oil to oil cooler
6.
Electric motor
7.
Steering wheel
8.
Supplemental steering pump
9.
Metering valve for steering
10.
Flow to relief valves and steering cylinders
11.
Combination valve
12.
Implement pump
13.
Check valves
14.
Pressure sensing switch
15.
Dump valve switch
16.
Dump valve
0352 00-30
TM 5-3805-261-23-2
0352 00
13
6
10
11
13
13
14
15
12
16
397-899
Figure 10. Supplemental Steering Hydraulic Schematic (Actuated).

0352 00-31
TM 5-3805-261-23-2
0352 00
2
3
LEGEND
1.
Start switch
2.
Ammeter
3.
Alternator
4.
Battery
5.
Starting motor
397-900
Figure 11. Charging System Schematic.

0352 00-32
TM 5-3805-261-23-2
0352 00
3
6
4
5
13
12
11
10
LEGEND
1.
Filler cap
8.
Inlet line for water pump
2.
Radiator
9.
Water pump
3.
Inlet line for radiator
10.
Internal bypass
4.
Water temperature regulator
11.
Bonnet
5.
Engine oil cooler
12.
Transmission oil cooler
6.
Cylinder head
13.
Cylinder liner
7.
Cylinder block
397-901
Figure 12. Cooling System Schematic.

0352 00-33
TM 5-3805-261-23-2
0352 00
LEGEND
1.
Fuel tank
2.
Fuel return line
3.
Priming pump
4.
Fuel injection nozzle
5.
Fuel injection line
6.
Fuel injection pump
7.
Primary fuel filter
8.
Check valves
9.
Fuel transfer pump
10.
Secondary fuel filter
11.
Constant bleed valve
12.
Fuel injection pump housing
0352 00-34
TM 5-3805-261-23-2
0352 00
1
4
2
3
8
7
9
10
11
12
397-902
Figure 13. Fuel System Schematic.

0352 00-35
TM 5-3805-261-23-2
0352 00
LEGEND
1.
Oil pressure connection
2.
Piston cooling orifices
3.
Oil supply for turbocharger
4.
Oil passage through rocker shaft to rocker arms
5.
Oil pressure connection
6.
Camshaft bores
7.
Oil manifold
8.
Filter bypasss
9.
Turbocharger
10.
Oil filter
11.
Oil cooler
12.
Oil sump
13.
Oil pump
14.
Oil cooler bypass
15.
Balancer shaft bores
0352 00-36
TM 5-3805-261-23-2
0352 00
2
6
1
15
14
11
10
13
12
397-903
Figure 14. Lubrication System Schematic.

0352 00-37
TM 5-3805-261-23-2
0352 00
LEGEND
1.
2.
Oil filter
No. 1 clutch lubrication passage
3.
No. 2 clutch lubrication passage
4.
Main relief valve
5.
Oil cooler
6.
Housing for transfer gears
7.
Oil pump
8.
Planetary transmission
9.
Differential lock valve
10.
Selector valve group
11.
Transmission reservoir
12.
Main reservoir in intermediate housing
13.
Differential reservoir
14.
Magnetic screen filter
15.
Magnetic screen filter
16.
No. 1 direction clutch
17.
No. 2 direction clutch
397-884
0352 00-38
TM 5-3805-261-23-2
0352 00
6
7
16
17
9
10
15
11
12
14
13
397-904
Figure 15. Transmission Hydraulic Schematic.

0352 00-39
TM 5-3805-261-23-2
0352 00
LEGEND
A.
B.
Passage for signal pressure

E.
F.
G.
1.
Oil filter
4.
Main relief valve
5.
Oil cooler
7.
Oil pump
9.
Differential lock valve
14.
Manual modulation valve
15.
Differential, check and safety spool
16.
Pilot selector spool
17.
Speed selector spool (No. 4 clutch)
18.
19.
Passage from load piston
20.
Relief valve
21.
Passage to differential, check and safety valve
22.
Passage to No. 4 clutch
23.
24.
Cooler bypass valve
25.
Lubrication relief valve
26.
Passage to differential lock clutch
27.
Passage to differential, check and safety valve
28.
Direction selector valve
29.
Priority reducing valve
30.
31.
Modulating reducing valve
32.
Load piston
33.
Passage to No. 1 clutch (FORWARD)
34.
Passage to No. 2 clutch (REVERSE)
35.
Speed selector spool (No. 6 and No. 7 clutches)
36.
37.
38.
0352 00-40
TM 5-3805-261-23-2
0352 00
14
15
20
17
18
19
16
22
21
24
25
A B E F G
23
E
26
27
1
5
28
29
32
31
30
33
34 35
7
B
37
F
36
38
397-905
Figure 16. Transmission Control Valves Schematic.
0352 00-41/(-42 Blank)
TM 5-3805-261-23-2
Figure 17. 130G Electrical Schematic (Sheet 1 of 2).

0352 00-1
TM 5-3805-261-23-2
Figure 17. 130G Electrical Schematic (Sheet 2 of 2).

0352 00-2
TM 5-3805-261-23-2
INDEX
Subject
Work Package/Page
A
Actuator and Release Valve, Parking Brake Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0312 00-1
Adapter Replacement, Engine-To-Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0295 00-1
Air Brake Valve Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0316 00-1
Air Compressor
Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lines and Fittings Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0317 00-1
0318 00-1
Arm Replacement, Blade Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0341 00-1
Articulation
Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hitch Bearing Replacement (CCE and Type I Machines) . . . . . . . . . . . . . . . . . . . . . . . . .
Hitch Bearing Replacement (Type II Machine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0336 00-1
0325 00-1
0326 00-1
Axle Assembly Replacement, Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0300 00-1
Axles Replacement, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0307 00-1
B
Bar Assembly Maintenance, Blade Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0340 00-1
Blackout
Light Wiring Harness Replacement, Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light Wiring Harness Replacement, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0288 00-1
0289 00-1
Blade Brackets Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0343 00-1
Blade Lift
Arm Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bar Assembly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0341 00-1
0340 00-1
0335 00-1
Blade Tip Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0334 00-1
Brake and Wheel Spindle Housing Assembly, Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . .
0314 00-1
Brakes Maintenance, Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0313 00-1
C
Cab Main Wiring Harness Replacement (CCE Machine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0292 00-1
Centershift Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0333 00-1
Chain Assembly Replacement, Tandem Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0311 00-1
Circle Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0344 00-1
Circle Drive Motor Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0331 00-1
Circle Drive Swivel Assembly Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0345 00-1
Combination Valve Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0323 00-1
Compressor, Air
Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lines and Fittings Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0317 00-1
0318 00-1
Index-1
TM 5-3805-261-23-2
INDEX - Continued
Subject
Work Package/Page
C - Continued
Console Base Replacement, Operators Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0328 00-1
Control Pump Maintenance, Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0319 00-1
Control Valve
Differential Lock, Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0306 00-1
0332 00-1
Cylinder Block Head Assembly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0270 00-1
Cylinder Repair
Articulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blade Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blade Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Centershift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leaning Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scarifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sideshift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0336 00-1
0335 00-1
0334 00-1
0333 00-1
0304 00-1
0338 00-1
0337 00-1
0320 00-1
D
Diagrams, Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0352 00-1
Differential
Lock Control Valve Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0306 00-1
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0294 00-1, 0305 00-1
Drawbar Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0342 00-1
Drive
Axles Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sprockets Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0307 00-1
0308 00-1
Drive Assembly Replacement, Final . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0309 00-1
Drive Tandem
Chain Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Assembly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0311 00-1
0310 00-1
E
Electronic Monitoring System (EMS)
Main Wiring Harness Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Panel Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0291 00-1
0284 00-1
Engine
Front Covers Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0269 00-1
0267 00-1
Engine, Mounting and Trunnion Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0268 00-1
Engine-To-Transmission Adapter Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0295 00-1
Exhaust Manifold Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0277 00-1
Index-2
TM 5-3805-261-23-2
INDEX - Continued
Subject
Work Package/Page
F
Final Drive Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0309 00-1
Flywheel and Flywheel Housing Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0272 00-1
Frame Separation and Connection Replacement (CCE and Type I Machines) . . . . . . . . . . . . .
0324 00-1
Front Axle Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0300 00-1
Fuel Injection
Nozzles Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pump Mounting Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pump Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0278 00-1
0280 00-1
0279 00-1
Fuel Transfer Pump Maintenance (Models 130G, 130GSCE, and 130GNSCE) . . . . . . . . . . . .
0281 00-1
G
Gauge(s) Replacement Transmission Oil Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0299 00-1
Governor Controls
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0282 00-1
0282 00-1
H
Head Assembly Maintenance, Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0270 00-1
Hitch Bearing Replacement, Articulation

CCE and Type I Machines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Type II Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0325 00-1
0326 00-1
Hoses, Lines, and Fittings Replacement Air Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0318 00-1
Housing Assembly Maintenance, Tandem Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0310 00-1
Hub Driver Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0271 00-1
Hydraulic Control Valves Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0332 00-1
Hydraulic Pump
Assembly and Mounting Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembly Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Break-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0329 00-1
0330 00-1
0330 00-1
Hydraulic Tank
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0339 00-1
0339 00-1
I
Illustrated List of Manufactured Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0350 00-1
L
Leaning Wheel
Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mechanism Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index-3
0304 00-1
0303 00-1
TM 5-3805-261-23-2
INDEX - Continued
Subject
Work Package/Page
L- Continued
List Manufactured Items, Illustrated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0350 00-1
M
Main
Blackout Light Wiring Harness Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Harness Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0287 00-1
0286 00-1
Manufactured Items, Illustrated List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0350 00-1
N
Nozzles Maintenance, Fuel Injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0278 00-1
O
Oil Cooler Replacement Transmission Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0298 00-1
Oil Pan
Plate Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0275 00-1
0275 00-1
Oil Pump
Engine, Lines Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine, Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0276 00-1
0276 00-1
Operators Panel Console Base Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0328 00-1
P
Parking Brake Actuator and Release Valve Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0312 00-1
Pump Replacement
Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0276 00-1
0279 00-1
0329 00-1
0297 00-1
R
Rear Signal Light and Backup Alarm Wiring Harness Replacement . . . . . . . . . . . . . . . . . . . .
0285 00-1
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0346 00-1
Relief Valve Maintenance, Transmission Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0296 00-1
Remote Steer Air Valves Replacement (Type II Machine) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0315 00-1
Rocker Arm Assembly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0273 00-1
ROPS Replacement (CCE Machine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0327 00-1
S
Scarifier Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0338 00-1
Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0352 00-1
Separation and Connection, Frame (CCE and Type I Machine) . . . . . . . . . . . . . . . . . . . . . . . .
0324 00-1
Index-4
TM 5-3805-261-23-2
INDEX - Continued
Subject
Work Package/Page
S - Continued
Service Brake and Wheel Spindle Housing Assembly Replacement . . . . . . . . . . . . . . . . . . . .
0314 00-1
Service Brakes Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0313 00-1
Sideshift Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0337 00-1
Sprockets Replacement, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0308 00-1
Steering Control Pump Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0319 00-1
Steering Arms and Tie Rod Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0301 00-1
Steering Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0320 00-1
Steering Valve Maintenance

Dual Valve Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Single Valve Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0321 00-1
0322 00-1
Supplemental Steering Main Wiring Harness Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . .
0290 00-1
Swivel Assembly, Circle Drive Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0345 00-1
T
Tandem Drive
Chain Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Assembly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0311 00-1
0310 00-1
Tie Rod Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0301 00-1
Torque Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0351 00-1
Transfer Pump Maintenance, Fuel (Models 130G, 130GSCE, and 130GNSCE) . . . . . . . . . . .
0281 00-1
Transmission Control Relief Valve Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0296 00-1
Transmission Oil
Cooler Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filler and Oil Level Gauge Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pump Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0298 00-1
0299 00-1
0297 00-1
Transmission, Adapter, and Differential Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0294 00-1
Trunnion Replacement, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0268 00-1
Turbocharger Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0283 00-1
V
Valve Maintenance
Combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering (Dual Valve Design) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering (Single Valve Design) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0323 00-1
0321 00-1
0322 00-1
Valves Maintenance, Cylinder Blade Head Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0274 00-1
W
Wheel Spindle, Bearings, and Seals Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index-5
0302 00-1
TM 5-3805-261-23-2
INDEX - Continued
Subject
Work Package/Page
W - Continued
Wiper (CCE Machine) Wiring Harness Replacement, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . .
0293 00-1
Wiring Harness(es) Replacement

Cab, Main (CCE Machine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic Monitoring System (EMS), Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Blackout Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Blackout Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Blackout Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Signal Light and Backup Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplemental Steering, Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiper, Rear (CCE Machine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0292 00-1
0291 00-1
0288 00-1
0286 00-1
0287 00-1
0289 00-1
0285 00-1
0290 00-1
0293 00-1
Index-6
By Order of the Secretary of the Army:
PETER J. SCHOOMAKER
General, United States Army
Chief of Staff
Official:
JOYCE E. MORROW
Administrative Assistant to the
Secretary of the Army
0604104
Distribution:
To be distributed in accordance with the initial distribution number (IDN) 255785,
requirements for TM 5-3805-261-23-2.
1 July 2006
AMSTA-LC-LMIT/TECH PUBS, TACOM-RI

1 Rock Island Arsenal
Rock Island, IL 61299-7630
TM 5-3805-261-23-2
0017 00-2
February 2007
Field Maintenance Manual (Includes

Unit and DS Maintenance) for Grader,
Road, Motorized, DED Heavy CCE
Part number supplied for item 2 is incorrect.

TM 5-3805-261-23-2
28 February 2007


TM 5-3805-261-23-2
28 February 2007

THE METRIC SYSTEM AND EQUIVALENTS

Linear Measure
Square Measure
1 Centimeter = 10 Millimeters = 0.01 Meters = 0.3937 Inches

1 Meter = 100 Centimeters = 1000 Millimeters = 39.37 Inches
1 Kilometer = 1000 Meters = 0.621 Miles
1 Sq Centimeter = 100 Sq Millimeters = 0.155 Sq Inches

1 Sq Meter = 10,000 Sq Centimeters = 10.76 Sq Feet
1 Sq Kilometer = 1,000,000 Sq Meters = 0.0386 Sq Miles
Weights
Cubic Measure
1 Gram = 0.001 Kilograms = 1000 Milligrams = 0.035 Ounces

1 Kilogram = 1000 Grams = 2.2 Pounds
1 Metric Ton = 1000 Kilograms = 1 Megagram = 1.1 Short Tons
1 Cu Centimeter = 1,000 Cu Millimeters = 0.06 Cu Inches

1 Cu Meter = 1,000,000 Cu Centimeters = 35.31 Cu Feet
Temperature
Liquid Measure
1 Milliliter = 0.001 Liters = 0.0338 Fluid Ounces
1 Liter = 1000 Milliliters = 33.82 Fluid Ounces
5/9 (F - 32) = C
212 Fahrenheit is equivalent to 100 Celsius
90 Fahrenheit is equivalent to 32.2 Celsius
32 Fahrenheit is equivalent to 0 Celsius
9/5 C +32 = F
APPROXIMATE CONVERSION FACTORS

To Change
To
Multiply By
To Change
To
Multiply By
Inches
Centimeters
2.540
Centimeters
Inches
0.394
Feet
Meters
0.305
Meters
Feet
3.280
Yards
Meters
0.914
Meters
Yards
1.094
Miles
Kilometers
1.609
Kilometers
Miles
0.621
Sq Inches
Sq Centimeters
6.451
Sq Centimeters
Sq Inches
0.155
Sq Feet
Sq Meters
0.093
Sq Meters
Sq Feet
10.764
Sq Yards
Sq Meters
0.836
Sq Meters
Sq Yards
1.196
Sq Miles
Sq Kilometers
2.590
Sq Kilometers
Sq Miles
0.386
Acres
Sq Hectometers
0.405
Sq Hectometers
Acres
2.471
Cubic Feet
Cubic Meters
0.028
Cubic Meters
Cubic Feet
35.315
Cubic Yards
Cubic Meters
0.765
Cubic Meters
Cubic Yards
1.308
Fluid Ounces
Milliliters
29.573
Milliliters
Fluid Ounces
0.034
Pints
Liters
0.473
Liters
Pints
2.113
Quarts
Liters
0.946
Liters
Quarts
1.057
Gallons
Liters
3.785
Liters
Gallons
0.264
Ounces
Grams
28.349
Grams
Ounces
0.035
Pounds
Kilograms
0.454
Kilograms
Pounds
2.205
Short Tons
Metric Tons
0.907
Metric Tons
Short Tons
1.102
Pound-Feet
Newton-Meters
1.356
Newton-Meters
Pound-Feet
0.738
Pounds per Sq
Inch
Kilopascals
6.895
Kilopascals
Pounds per Sq
Inch
0.145
Miles per Gallon
Kilometers per Liter
0.425
Kilometers per Liter
Miles per Gallon
2.354
Miles per Hour
Kilometers per Hour
1.609
Kilometers per Hour
Miles per Hour
0.621
PIN: 083034-000
This fine document...

Was brought to you by me:
Liberated Manuals -- free army and government manuals

Why do I do it? I am tired of sleazy CD-ROM sellers, who take publicly
available information, slap watermarks and other junk on it, and sell it.
Those masters of search engine manipulation make sure that their sites that
sell free information, come up first in search engines. They did not create it...
They did not even scan it... Why should they get your money? Why are not
letting you give those free manuals to your friends?
I am setting this document FREE. This document was made by the US
Government and is NOT protected by Copyright. Feel free to share,
republish, sell and so on.
I am not asking you for donations, fees or handouts. If you can, please
provide a link to liberatedmanuals.com, so that free manuals come up first in
search engines:
<A HREF=http://www.liberatedmanuals.com/>Free Military and Government Manuals</A>
Sincerely
Igor Chudov
http://igor.chudov.com/

TM 5 3805 261 23 2 PDF

Uploaded by

Copyright:

Available Formats

TM 5 3805 261 23 2 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TM 5 3805 261 23 2 PDF

Uploaded by

Copyright:

Available Formats

What safety icons are explained in the document?

What safety icons are explained in the document?

What warnings are provided about engine exhaust?

What warnings are provided about engine exhaust?

TM 5-3805-261-23-2

FIELD MAINTENANCE MANUAL

GRADER, ROAD, MOTORIZED, DIESEL ENGINE DRIVEN (DED), HEAVY,

TYPE II, SECTIONALIZED

HEADQUARTERS, DEPARTMENT OF THE ARMY

only Left Blank.

This page is blank.

POISON - skull and crossbones shows material is poisonous or is a danger to life.

FOR INFORMATION ON FIRST AID, REFER TO FM 4-25.11.

DO NOT operate engine in enclosed areas.

DO NOT idle engine without adequate ventilation.

DO NOT drive machine with inspection plates or cover plates removed.

BE ALERT for exhaust poisoning symptoms. They are:

If you see another person with exhaust poisoning symptoms:

The Best Defense Against Carbon Monoxide Poisoning Is Good Ventilation!

To order this NBC decal use:

LIST OF EFFECTIVE PAGES/WORK PACKAGES

Date of issue for original manual is:

DA Form 2028 Sample

Metric Convsersion Chart

* Zero in this column indicates an original page or work package.

Fuel Injection Nozzles Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278 00-1

Electronic Monitoring System (EMS) Panel Repair . . . . . . . . . . . . . . . . . . . . .

Transmission, Adapter, and Differential Replacement . . . . . . . . . . . . . . . . . . .

Table of Contents - Continued

Front Axle Assembly Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parking Brake Actuator and Release Valve Repair. . . . . . . . . . . . . . . . . . . . . .

Steering Control Pump Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Frame and Articulation Systems

Hydraulic Pump Assembly and Mounting Replacement . . . . . . . . . . . . . . . . .

Table of Contents - Continued

Blade Lift Bar Assembly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CHAPTER 5 SUPPORTING INFORMATION

References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0346 00-1

HOW TO USE THIS MANUAL

Due to the size of this manual, it is separated into two volumes:

The second volume (TM 5-3805-261-23-2) contains Chapter 4.

Both volumes have Chapter 5, Supporting Information, for reference purposes.

CONTENTS OF THIS MANUAL

Chapter 4 covers Direct Support Field Maintenance Instructions.

FEATURES OF THIS MANUAL

THIS WORK PACKAGE COVERS

Equipment Conditions - Continued

Engine off (TM 5-3805-261-10)

Tools and Special Tools

Battery cables disconnected (WP 0125 00)

Tool kit, general mechanics (Item 89, WP 0348 00)

Articulation anti-pivot pin installed (TM 5-3805261-10)

Leveler, load (Item 42, WP 0348 00)

Coolant drained (WP 0065 00)

Stand, engine (Item 85, WP 0348 00)

Radiator inlet and outlet tubes removed (WP 0057

Wrench, torque (Item 96, WP 0348 00)

Engine compartment dash plate removed (WP 0183

Supplemental steering motor