Simulation of First Benchmark Model For Analysis of Subsynchronous Resonance in Power Systems Using Sequel

International Journal of Engineering Research and Applications (IJERA) ISSN: 2248-9622
National Conference on Recent Advances in Power and Control Engineering (RAPCE-2k11)
SIMULATION OF FIRST BENCHMARK MODEL FOR

ANALYSIS OF SUBSYNCHRONOUS RESONANCE IN
POWER SYSTEMS USING SEQUEL
Mr.J.SREERANGANAYAKULU
Assistant Professor,
SITAMS,
Chittoor - 517127.
Abstract: This paper mainly focuses on the use
of upcoming and indigenous software SEQUEL
for analysis of Subsynchronous Resonance
phenomena in power systems. Here, the IEEE
First Benchmark system for Subsynchronous
resonance is simulated using SEQUEL for
comparison. The oscillations due to SSR are
observed between turbine-generator and between
various turbine shafts.
Keywords: SEQUEL, Self Excitation, Induction
generator effect, Torsional interaction, Transient
torque, Multimass model.
Introduction:
Worldwide series capacitors have been
extensively used for improving power factor and
thereby the power transmission. While it has
been known that series capacitors can cause selfexcited oscillations at low frequencies (due to
low X/R ratio) or at Subsynchronous frequencies
(due to induction generator effect), the problem
of self excited torsional frequency oscillations
(due to torsional oscillations) was first
experienced at Mohave power station in U.S.A.
in December 1970 and October 1971 [1]. The
problem of self excitation due to torsional
interaction is a serious problem and led to
detailed analysis and study.
The IEEE SSR working group defines
Subsynchronous Resonance (SSR) as an
electric power system condition where the
electric network exchanges energy with a turbine
generator at one or more of the natural
frequencies of the combined system below the
synchronous frequency of the system [2].
N.Chinna Alluraiah
Assistant Professor,
SITAMS,
Chittoor-517127.
Subsynchronous
frequency
currents
entering the generator terminals produce the
synchronous
frequency
teminal
voltage
components. These voltage components may
sustain the currents to produce the effect that is
termed as self excitation. There are two types of
self excitation, one involving only rotor electrical
dynamics and the other involving both rotor
electrical and mechanical dynamics. First one is
the induction generator effect while the second
one is called torsional interaction. Here, the
torsional interaction effect is more significant
when compared to induction generator effect.
Also, this can cause shaft damage as experienced
at Mohave generating station in U.S.A. [3].
Digital programs like Electromagnetic
Transient Programs (EMTP) and Simulator like
RTDS (Real Time Digital Simulator) are
available to perform the studies of
Subsynchronous Resonance. An indigenous up
coming software SEQUEL (A Solver for circuit
EQuations with User-defined ELements) has
been developed by IIT Bombay for the
simulation of the power electronic systems and
power systems. With the use of above software,
the First Benchmark model is developed and
simulated.
First Benchmark system for Subsynchronous
Resonance:
A single line diagram of the First
Benchmark model given by IEEE committee for
the study of Subsynchronous Resonance is as
shown in figure 1.
There are two aspects of the SSR problem

[1]. These are
1. Self excitation (Steady state SSR)
and
2. Transient torque (Transient SSR)
Vignans LARA Institute of Technology & Sciences
Page 15

Fig 1: Network for First Benchmark Model for SSR
synchronous generator to a large system. Here,

the circuit parameters are expressed in per unit
on the generator base of 892.4 MVA, 60 Hz
frequency. Reactances are proportional to
frequency and resistances are constant. This
system configuration corresponds to the Navajo
Projects 892.4 MVA, 500 kV transmission
systems. This model is flexible for addition of
new test cases (if any). Here, two fault locations
(A and B) are designated, and there is provision
for inclusion of a filter. The network parameters
are provided in appendix.
The network consists of a single series

compensated transmission line connecting a
Synchronous machine model
Simple models of synchronous generators are not
adequate for accurate description of the power
results in time-invariant machine equations
which are easier to handle. So, we consider a
Synchronous machine in the Park reference
frame (i.e. rotor reference frame) with one
damper winding in D-axis and two in the
Q-axis is considered as depicted in Figure 2.
Ia
Va
D-axis
Q-axis
h
Ib Vb
Vc
Ic
Figure 2: Synchronous machine model
system dynamics. So the detailed synchronous

machine model [1] developed from the basic
equations using phase variables and application
of Parks transformation is chosen. Parks
transformation
stator frequency is locked to the rotor speed to
avoid instability.
Equivalent circuit of Synchronous machine
There are two equivalent circuits
corresponding to the two axes d and q. These are
as shown in the Figure 3. On the d-axis there are
three coupled coils namely, armature d-coil, field
winding f, and damper winding h. By the
application of per unit system, all the quantities
get referred to the armature side.
All the reactances are expressed in per
unit. la is the armature leakage reactance. lf
and ld can be viewed as the leakage
inductances of the field and the d-axis damper
windings respectively. LAD represents the per
unit mutual inductance (between the field and
damper windings). Coming to equivalent circuit
on q-axis, both damper windings are short
circuited as shown in figure 2.
This model shows a three phase

armature windings (a, b and c) on the stator and
four windings on the rotor including field
winding f. The amortisseur (or damper) circuits
in the salient pole machine or the eddy-current
effects in the rotor are represented by a set of
coils with constant parameters. Three damper
coils, h in the d-axis and g, k on the q-axis are
shown in the Figure 4. Their dynamics can be
described by six simultaneous differential
equations using d, q, o in place of a, b, c
(neglecting the o axis differential equation).
The seventh equation is the electromechanical
torque equation. In a synchronous machine, the
Page 16

The voltage equations for the stator and

rotor coils are as given below:
- d / dt [RS] iS = vS
- d / dt - [Rr] ir = vr
Where, vtS = [va vb vc], vtr = [-vf 0 0 0]
and
Figure 3: The d and q axis per unit equivalent

circuits of synchronous machine
[RS] =
[Rr] =
Ra
Ra
Ra
Multi-mass model of the Turbine - Generator

Shaft
Rf
Rh
Rg
Rk
There are different models involved in

SEQUEL for the construction of the mechanical
multi-mass model. These are six masses
consisting of four different levels namely
Generator, High Pressure (HP), Low Pressure
(LPA and LPB), Intermediate Pressure (IP) and
an Exciter. All these six masses are coupled to
the same shaft.
Mechanical multi-mass system with
different masses namely HP, IP, LPA, LPB
turbines, Generator and an exciter connected to
the same shaft is shown in figure 4 below.
The transformed voltage equations (Parks

transformation) in the D and Q axis windings
such as vd, vq, vfd etc. are shown in below.
vd = ra * id r * lq * iq - r * lkq * ikq +
ld * id + lmd * (ifd+ihd)
vq = r * ld * id + ra * iq r * lfd * ifd
r * lhd * ihd + lq * iq+ lmq * (igq+ikq)
vfd = rfd * ifd + lmd * id + lfd * ifd + lfh * ihd
0 = - rhd * ihd + lmd * id + lfh * ifd + lhd * ihd
0 = - rgq * igq + lmq * iq + lgq * igq +lgk * ikq
0 = - rkq * ikq + lmq * iq + lgk* igq + lkq * ikq
The machine Torque equations are given by
Tem=3/2*P/2(Lmd*iqs*ifd+(LdLq)*iqs*ids+Lmd*iqs*ihd-Lmq*ids*igqLmq*ids*ikq)
2/P (J d2m/dt2+D*dm/dt) =Tm-Te
Figure 4: Block Diagram of the mechanical

multi-mass system
This is a mechanical system which has
several rotors corresponding to different stages
of steam turbines, generator and rotating exciter.
These are connected by shaft sections which are
not rigid and act as springs. That is, when an
external torque is applied to one end of the shaft
it twists. The torque transmitted by the shaft can
be assumed to be directly proportional to the
difference between the angular positions of the
shaft at the two ends.
Page 17

The torsional system consisting of six

masses is shown in the figure 5. This figure
shows a mechanical multi-mass system of mass,

spring and dash pots.
LPA : 2H2 d (2) / dt = TLPA +K23 (3-2)
K12 (2-1) D2 (2)
d 2 / dt = (2)0
LPB : 2H3 d (3) / dt = TLPB + K34 (4- 3)
K23 (3-2) D3 (3)
Figure 5: Lumped Spring-Mass Model of a

Turbine-Generator shaft
d 3 / dt = (3) 0
IP : 2H4 d (4) / dt = TIP + K45(5- 4)
The system, when considered in

isolation, has resonant frequencies of oscillation
termed as torsional modes (10 to 45 Hz). When a
transient electrical torque is applied (at the
generator mass) the response of the torsional
system depends on the frequencies contained in
the torque transient. If one of the frequencies in
the applied torque is close to one of the torsional
frequencies, the oscillations in the generator
rotor (with respect to a synchronously rotating
reference) have significant amplitudes and result
in emfs generated in the stator windings. These
emfs also are at sub and super synchronous
frequencies and the subsynchronous frequency
component tends to sustain the armature currents
(and the rotor oscillations).
The various components of torque
associated with the generator rotor are as
follows:
Input torque
= T 12 = K12 (2-1)
Output torque
= Te
Damping torque
= D1 (1)
Accelerating torque
= T a =T12-Te- D1 1
The equations of the complete rotor system

shown in figure 5 are as follows:
GEN: 2 H1 d (1) / dt = K12 (2-1) Te
D1 (1)
d 1 / dt = (1)0
K34 (4- 3) D4 (4)

d 4 / dt = (4) 0
HP : 2H5 d (5) / dt = THP + K45(5- 4)
D5 (5)
d 5 / dt = (5) 0
EXC: 2H6 d (6) / dt = TEXC + K56 (6- 5)
D6 (6)
d 6 / dt = (6) 0
Simulations and Results:

The SEQUEL library components such as
multimass model (Synchronous machine,
Turbines and exciter), transmission line and
infinite source are connected as in figure 1. and
the circuit file is made in SEQUEL. The system
is simulated for the same operating condition as
in reference [3]. For the transient case, phase to
ground fault is applied at bus B in figure 3 for
duration of 75 msec from 0.1 seconds to 0.175
seconds. In the reference paper, fault reactance is
0.04 p.u. and it is adjusted to produce a capacitor
transient voltage approaching the lower gap
setting. But in SEQUEL the fault reactance could
not be modeled and fault resistance is modeled.
Capacitor voltage, Generator current,
Generator Electrical Torque, Shaft Torque of
LPA-LPB and GEN-EXC are plotted for the
Page 18

same time duration as in the reference paper for
comparison.
Figure 6 shows the variation of voltage
across the capacitor in per unit. The Capacitor
voltage is varying up to 1 p.u. and it is settling
down to a constant value after 0.3 seconds.
Fig 6: variation of voltage across capacitor

oscillations between generator and the turbine
shafts.
Figure 7 shows the variation of the

machine current in per unit. From the graph, it is
seen that the machine phase current is
oscillatory.
Fig 7: Variation of machine current in phase a

The figure 8 shows the variation of generator
electrical torque TGEN due to the SSR
The figure 10 shows the shaft torque in
GENERATOR-EXCITER. This result shows
that this system is not going to self-excitation
mode within 0.5 seconds as in the reference
paper. The results of the reference paper are
given in figure 11.
Figure 8: Generator Electrical Torque
The figure 9 shows the shaft torque between the

low pressure turbines LPA and LPB. From the
graph, it is seen that the shaft torque oscillates
due to SSR phenomena.
Shaft
Generator
and
A Figure
slight 10:
shift
inTorque
these between
waveforms
is also
Exciter
observed if these waveforms are compared
closely with the reference results. It is due to the
point of switching on the fault which is not yet
implemented in SEQUEL due to time limitation.
As it is known that the results from two different
softwares differ slightly due to the simulation
time step and the method of solving the nonlinear equations.
As an attempt is made to develop the
electrical components from the basic equations
instead of using the component modeled readily
available, the results from the SEQUEL and the
reference paper are found to be closely matching.
Figure 9: Shaft Torque between LPA and LPB
Page 19

committee [3]. Further refinement in the
SEQUEL models can be carried out as a future
work to get exactly the same results as in IEEE
committee report.
Appendix
The network parameters of the synchronous
machine working as generator are as follows:
a. Generator parameters:
Rated MVA: 892.4
Rated voltage: 26.0 kV
Power Factor: 0.9
Xa = 0.13 pu; Xd = 1.79 pu
Xd= 0.169 pu; Xl = 0.135 pu
Xq = 1.71 pu; Xq= 0.228 pu
Xq= 0.2 pu;
Ra = 0.002 pu
Td0 = 4.3 s; Td0 = 0.032 s
Tq0 = 0.85 s; Tq0 =0.05 s
b. Mechanical Parameters:
Mass
Inertia (Secs)
HP
IP
LPA
LPB
GEN
EXC
0.0929
0.1556
0.8587
0.8842
0.8686
0.0342
Shaft
Figure 11: Transient Response of IEEE First

Benchmark Model given by IEEE committee
Conclusion
In this paper, the First Benchmark
Model
for
computer
simulation
of
Subsynchronous resonance is simulated in
SEQUEL (Solver for circuit Equations with User
defined Elements). The simulation is carried out
for same operating condition as in [3].
Subsynchronous Resonance Phenomena is
simulated by exciting the torsional modes with
three phase to ground fault for duration of four
and half cycles. The results obtained are closely
matching with the reference results except for the
self-excitation case. The slight difference in the
results is attributed to the difference in modeling
of the components and method of solving the
non-linear equations. These results are in full
agreement with those given by the IEEE
Spring Constant Turbine Torque

(p.u.)
(p.u.)
HP-IP
7277
0.3
IP-LPA
13168
0.26
LPA-LPB
19618
0.22
LPB-GEN
26713
0.22
GEN-EXC
1064
0.22
c. Transformer Parameters:
Rated MVA: 892.4
Voltage Rating: 26/539 kV
Delta / Star grounded
R = 0.00792 pu
X = 0.14 pu
X0 = 0.14 pu
d. Transmission line parameters:
R = 3.9344
X = 162.97
e. Series capacitor:
C = 21.977 F
f. Infinite Bus:
Voltage: 477.8 kV RMS L-L
Phase angle: 3.8 lagging
Page 20

Series impedance: 19.5206
g. Fault Impedance:
Resistance: 4830.0
Reactance: 13.00
References:
1. K.R. Padiyar, Power System Dynamics
Stability and Control, Indian Institute of
Science, Bangalore, 1996.
2. P.M. Anderson, B.L. Agrawal, J.E. Van
Ness,Subsynchronous Resonance in Power
Systems, IEEE Press, New York, 1990.
3. IEEE SSR Working Group, First
Benchmark Model for Computer Simulation of
Subsynchronous
Resonance,
IEEE
Transactions on Power Apparatus and Systems,
Vol. PAS-96, no. 5, September/October 1977.
4. M.H. and M.K. Donnelly Thyristor-Based
Damping
of
Turbine-Generator
Shaft
Torsional Oscillations Resulting From Power
System Disturbances and Subsynchronous
Resonance: A Review, Montana State
University, Bozeman, MT 59717, R. Adapa,
Electric Power Research Institute, Palo Alto, CA
94303, 1990.
5. Mahesh B. Patil, SEQUEL Users Manual,
Indian Institute of Technology, Bombay.
6. RTDS Users Manual Set, Central Power
Research Institute, Bangalore.
7. O.Wasynczuk, Damping Subsynchronous
Resonance using Reactive Power Control,
IEEE Transactions on Power Apparatus and
Systems, Vol. PAS100, No. 3, March 1981.
8. O.Wasynczuk, Damping of shaft torsional
oscillations using a dynamically controlled
resistor bank, IEEE transactions on power
apparatus and systems, vol 100, no. 7, 1981.
9. K.R.Padiyar, Power System Dynamics and
Stability, McGraw-Hill, 1990.
Page 21

Simulation of First Benchmark Model For Analysis of Subsynchronous Resonance in Power Systems Using Sequel

Uploaded by

Copyright:

Available Formats

Simulation of First Benchmark Model For Analysis of Subsynchronous Resonance in Power Systems Using Sequel

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Simulation of First Benchmark Model For Analysis of Subsynchronous Resonance in Power Systems Using Sequel

Uploaded by

Copyright:

Available Formats

International Journal of Engineering Research and Applications (IJERA) ISSN: 2248-9622

National Conference on Recent Advances in Power and Control Engineering (RAPCE-2k11)