Arnott Motorcycle Air Suspension For Bagger

Kit # 9010-AL/AS
Harley-Davidson Touring Models

1980 - 2007
Motorcycle Air Suspension
Engineered to Ride, Built to Last

PARTS LIST
REAR AIR SUSPENSION SHOCK
VIAIR COMPRESSOR W/BRACKET ASSEMBLY
TOGGLE SWITCH
DISTRIBUTION MANIFOLD
SPEED REDUCING MUFFLER
MANIFOLD BRACKET W/FASTENERS
FUSED WIRING HARNESS
RELAY ASSEMBLY
X 2.0 SOCKET HEAD BOLTS
SPACER WASHERS
BOLT COVERS
NYLON TUBING
4mm NYLON TUBING
4mm VOSS AIR FITTINGS
HARNESS CABLE TIES
SPLIT LOOM
Copyright 2008, Arnott Inc.
PART NUMBER
21-2583 (AS)
21-2782
20-2592
21-2866
29-2710
14-2849
21-2698
21-3110
29-2856
14-3235
14-2680
29-2627
29-2625
29-2618
29-2617
29-3000
PART NUMBER
21-2555 (AL)
QUANTITY
1
1
1
1
1
1
1
1
4
4
4
6-FT
6-FT
5
8
3-FT
Rev. #09 12/31/2008
Harley-Davidson
Touring Models
1980 - 2007
4MM
VOSS
FITTINGS
P/N: 29-2618
4MM TUBING
P/N: 29-2625
ALDAN
SHOCK
ALDAN
SHOCK
1/4" TUBING
P/N: 29-2627
FUSED
WIRING HARNESS
P/N: 21-2698
MICRO RELAY
P/N: 21-3110
RED
BLACK (#2)
RED
15-AMP
RED
4MM
VOSS FITTINGS
P/N: 29-2618
COMPRESSOR
P/N: 21-2782
RED (#3)
ORANGE
RED
ORANGE (#1)
RED (#5)
RED
RED
PRESSURE
TRANSDUCER
IS ONLY USED ON
EAC-3 SYSTEMS
BLACK
BLACK
BLACK
TOGGLE SWITCH
P/N: 20-2592
NOTE:
AL = 13" ALDAN SHOCK ASSEMBLY (21-2555)
AS = 11.6" ALDAN SHOCK ASSEMBLY (21-2583)
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ARNOTT, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
ARNOTT, INC. IS
PROHIBITED.
SOLENOID
DISTRIBUTION
VALVE BLOCK
P/N: 21-2866
BLACK
+12V
MATERIAL
DRAWN
NAME
DATE
KMD
03/25/08
CHECKED
9010-AL/AS
TOURING BIKE
1980 - 2007
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
NEXT ASSY
USED ON
APPLICATION
FINISH
DO NOT SCALE DRAWING
SIZE
DWG. NO.
SCALE: NONE WEIGHT:
REV.
35-2894
SHEET 1 OF 1
THANK YOU!
Thank you for purchasing the Arnott Cycle Air System! This system provides you with the ability to
maintain your bike at a constant level regardless of load, resulting in enhanced vehicle ride, handling, and
performance.
Proper installation is essential to experience and appreciate the benefits of this system. Please take a
moment to review these installation instructions before you begin to install this system on your bike.
Reviewing the components and the parts list below will familiarize you with the system.
It is equally important to be aware of and take all necessary safety measures while installing your new Air
Ride System. This includes proper lifting and immobilizing of the bike, and isolation of any stored energy
to prevent personal injury or property damage.
SAFTEY WARNING:
Do not inflate the air spring assembly unless it is supported on both ends by the vehicle frame and
suspension system, or by another adequate means. Doing so may result in serious injury and damage to
the air spring assembly and surrounding environment.
The maximum recommended inflation pressure of the air spring is 100 psi. Over-inflation of the air
spring, as well as improper use or installation of the assembly, may result in serious injury and damage to
the air spring assembly and the surrounding environment.
Take precautions not to exceed the Gross Vehicle Weight Rating (GVWR, or the maximum load)
recommended by the manufacturer. The air springs are rated for a maximum pressure of 100 psi. This
pressure may, however, allow too great a load to be carried on most vehicles. For best results, load the
vehicle and have it weighed, then compare the vehicle weight with the maximum allowed. Consult your
recommended load. It is important that all vehicles Owner Manual recommendations are followed for
your own safety and to prevent damage to the vehicle. Air Springs DO NOT increase the GVWR set by the
manufacture.
NEVER MAKE ADJUSTMENTS TO THE AIR RIDE SYSTEM

WHILE THE VEHICLE IS IN MOTION. ADJUSTNG THE AIR
SUSPENSION WHILE VEHICLE IS IN MOTION CAN AFFECT
WARNING THE STABLIITY AND HANDLING, WHICH COULD RESULT
IN DEATH OR SERIOUS INJURY.
[1]
(A.) PREPARING THE BIKE:

On a solid level surface, position the bike on a motorcycle lift and use all the recommended safety
techniques. Lift the bike so the rear wheel is just slightly off the ground. Be sure to refer to the Owners
Manual for the bike and the motorcycle lift for all correct lifting instructions. It is also recommended that you
protect any chrome or painted surfaces that may be damaged during lifting or installation procedure.
REMOVE THE SEAT BEFORE STARTING THE INSTALLATION
(B.) REMOVING THE FACTORY SHOCKS:
1. Remove the air hose from the factory shocks. To

disconnect the air line, push down on the red
plastic ring while pulling out on the air line at the
same time.
2. Loosen and remove the upper and lower shock

bolts.
3. Carefully remove factory shock absorbers from

the rear suspension.
4. Remove the factory air line and valve
[2]
(C.) INSTALLING THE REAR AIR SHOCKS:
1. Locate and remove the X 2.0 socket head

bolts from the kit. Before installing, apply two or
three drops of Loctite 243 (blue) to the threads of
new shock bolts.
2. Install the new air ride shocks one at a time. Start

the lower bolts first. Then adjust the height of the
bike to line up the upper bolt holes.
NOTE:
Check clearances on the left side shock between the shock
and pulley, shim with included spacer washers as needed.
3. Use a 38 Allen head driver and torque wrench to

tighten the upper and lower shock bolts to 35-40
ft-lbs (45-48 Nm).
4. Install the bolt covers onto the shock absorber

bolts. Lubricate the inside with a lube appropriate
for o-rings. Gently press the cover on with a slight
twisting motion until you feel it drawn solidly onto
the bolt head and firmly seated.
[3]
(D.) INSTALLING THE INFLATION SYSTEM:

The inflation system consists of a compressor with a separate distribution manifold along with an inflation
switch and compressor relay. Pump locations may be affected by emissions control components. If
equipped an alternate pump location will need to be found.
Split loom is provided to cover the air hose as well as protect and hide any exposed wiring.
1. Remove the seat.
2. Disconnect and remove the battery from the

bike. (Always remove the negative (-) cable first)
3. Remove both side cover panels. Then use a

thin-wall 716 socket to remove the two nuts
holding the control module mounting plate
located on the right side of the bike. Make sure you
have complete access to the hole located under
the battery box.
4. Carefully slide the compressor assembly into the

hole located under the battery box. Push the
compressor bracket through the stamped,
wedge-shaped holes on the bottom of the battery
box. You may find it necessary to clean the bottom
side of the battery box before inserting the
bracket.
[4]
5. Slide the compressor towards you until the hole

in the compressor bracket lines up with the
stamped hole in the bottom of the battery box.
Fasten in place using the 10-32 button head screw
and lock nut supplied with the compressor. The
lock nut should be on the under side of the battery
box.
6. Connect the larger line from the kit to the

compressor using the push to connect fitting.
Route the air line up and in front of the battery box.
Exit the air line into the open cavity located directly
behind the gas tank.
7. Behind the fuel tank and under the seat is a

preferred location for the solenoid/distribution
valve block assembly. Connect the air line
leading from the compressor to the push to
connect fitting on the distribution valve block.
8. Locate the smaller 4mm tubing from your kit.

Measure and cut the air hoses leading from the
valve block to the rear air shocks. Assemble the
VOSS air fittings onto the air hose and route both
air lines along the frame rail and back to the rear air
shocks. (Assembly instructions are included with
VOSS air fittings) Note: the air fittings seal with
O-Rings, Do not overtighten the fittings.
NOTE: Make sure air line is cut square on the

ends to ensure a good seal in the fitting.
[5]
9. Assemble the VOSS air fittings onto the other

end of the 4mm air tubing and screw the fittings
into the shocks.
NOTE: VOSS fittings seal with O-Rings, Do not
overtighten!
10. Locate a suitable mounting location for your

toggle switch. Mount in a location that will provide
ease of access. Such as behind the rear cylinder on
the front of the battery box.
11. Included in the kit is a system relay, refer to the

schematic on the back of the cover for a wiring
diagram. Only after all electrical connections are
made, attach the ring terminal end of the fused
wire harness to the positive(+) battery terminal
and reconnect the battery.
12. Replace the control module, side panels and

reconnect the battery.
NOTE: If installing the upgrade handlebar mounted

control switch, follow the wiring instructions included
with upgrade switch.
NOTE: A system schematic is included for reference.
[6]
13. When finished and the system is operational,

check clearances between the tire and fender as well
as the shock and drive pulley. Inflate the system and
use a soap and water solution to check for leaks.
14. Replace the seat and saddlebags.
Thank you for purchasing an Arnott Air Ride Suspension Product!

Each owner or installer is unique, therefore installation of this system can be done many different ways.
The mounting locations of the compressor and inflation switch are suggestions by our engineers. If
proper wiring guidelines and instructions are followed, relocation of the compressor or switch will
neither affect the system operation nor void your warranty.
Adjust air spring pressure as required for desired ride quality to maximize the benefits of your system.
Excess pressure will result in a firmer ride, too little pressure will allow the suspension to bottom out.
WARNING
DO NOT ADJUST THE AIR RIDE SYSTEM WHILE THE BIKE IS IN

MOTION, DOING SO CAN AFFECT STABILITY AND HANDLING,
THIS COULD RESULT IN DEATH OR SERIOUS INJURY.
DISCLAIMER
The terms Harley-Davidson, Harley, H-D, Buell, Softail, Dyna, V-Rod and Sportster are used for reference only. Arnott
Air Suspension products are in no way authorized by nor associated with the Harley-Davidson Motor Company. All references
to Harley-Davidson terms and models are for reference and identification purposes only.
The use and installation of any Arnott Air Suspension product or kit may adversely affect or void your Harley-Davidson
factory warranty. It is the responsibility of the motorcycle owner to check federal, state and local laws and ordinances before
modifying or customizing his or her motorcycle. It is the exclusive and total responsibility of the motorcycle owner to
determine the suitability of this product for his or her use. The user shall assume all legal obligations, personal injury risk and
all liability duties and risk associated with the use of this product. Arnott Air Suspension products are designed and intended
for the experienced off-road motorcyclists only and intended for closed course operation.
Arnott Air Suspension products and kits are designed exclusively for OEM manufactured and equipped motorcycles with no
modifications. Any installation of aftermarket or customized components may adversely affect the operation and
performance of Arnott Air suspension kits and components and may void the manufacturers warranty. These directions are
accurate at time of publication. Arnott Inc. reserves the right to revise specifications without notice.
[7]

Arnott Motorcycle Air Suspension For Bagger

Uploaded by

Copyright:

Available Formats

Arnott Motorcycle Air Suspension For Bagger

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Arnott Motorcycle Air Suspension For Bagger

Uploaded by

Copyright:

Available Formats

What components are included in the air suspension kit?

What components are included in the air suspension kit?

What safety precautions should be taken during installation?

What safety precautions should be taken during installation?

Kit # 9010-AL/AS

Harley-Davidson Touring Models

Motorcycle Air Suspension

Engineered to Ride, Built to Last

Copyright 2008, Arnott Inc.

Rev. #09 12/31/2008

PROPRIETARY AND CONFIDENTIAL

DO NOT SCALE DRAWING

SCALE: NONE WEIGHT:

NEVER MAKE ADJUSTMENTS TO THE AIR RIDE SYSTEM

(A.) PREPARING THE BIKE:

(B.) REMOVING THE FACTORY SHOCKS:

1. Remove the air hose from the factory shocks. To

2. Loosen and remove the upper and lower shock

3. Carefully remove factory shock absorbers from

4. Remove the factory air line and valve

(C.) INSTALLING THE REAR AIR SHOCKS:

1. Locate and remove the X 2.0 socket head

2. Install the new air ride shocks one at a time. Start

3. Use a 38 Allen head driver and torque wrench to

4. Install the bolt covers onto the shock absorber

(D.) INSTALLING THE INFLATION SYSTEM:

1. Remove the seat.

2. Disconnect and remove the battery from the

3. Remove both side cover panels. Then use a

4. Carefully slide the compressor assembly into the

5. Slide the compressor towards you until the hole

6. Connect the larger line from the kit to the

7. Behind the fuel tank and under the seat is a

8. Locate the smaller 4mm tubing from your kit.

NOTE: Make sure air line is cut square on the

9. Assemble the VOSS air fittings onto the other

10. Locate a suitable mounting location for your

11. Included in the kit is a system relay, refer to the

12. Replace the control module, side panels and

NOTE: If installing the upgrade handlebar mounted

NOTE: A system schematic is included for reference.

13. When finished and the system is operational,

14. Replace the seat and saddlebags.

Thank you for purchasing an Arnott Air Ride Suspension Product!

DO NOT ADJUST THE AIR RIDE SYSTEM WHILE THE BIKE IS IN

You might also like