The document is a table from ASME B16.5-2009 that lists material specifications for metallic flanges, flanged fittings, and flanged valves. It includes the material group number, nominal material designation, applicable pressure-temperature rating table, and ASTM specifications for forgings, castings, and plates for each material. The table provides material traceability information for components within its scope.
The document is a table from ASME B16.5-2009 that lists material specifications for metallic flanges, flanged fittings, and flanged valves. It includes the material group number, nominal material designation, applicable pressure-temperature rating table, and ASTM specifications for forgings, castings, and plates for each material. The table provides material traceability information for components within its scope.
The document is a table from ASME B16.5-2009 that lists material specifications for metallic flanges, flanged fittings, and flanged valves. It includes the material group number, nominal material designation, applicable pressure-temperature rating table, and ASTM specifications for forgings, castings, and plates for each material. The table provides material traceability information for components within its scope.
The document is a table from ASME B16.5-2009 that lists material specifications for metallic flanges, flanged fittings, and flanged valves. It includes the material group number, nominal material designation, applicable pressure-temperature rating table, and ASTM specifications for forgings, castings, and plates for each material. The table provides material traceability information for components within its scope.
GENERAL NOTES: (a) For temperature limitations, see notes in Tables II-2-1.1 through II-2-3.17 of Mandatory Appendix II. (b) Plate materials are listed only for use as blind flanges and reducing flanges without hubs (see para. 5.1). Additional plate materials listed in ASME B16.34 may also be used with corresponding B16.34, Standard Class ratings. NOTE: (1) ASME Boiler and Pressure Vessel Code, Section II materials may also be used, provided the requirements of the ASME specification are identical to or more stringent than the corresponding ASTM specification for the Grade, Class, or Type listed.
(a) Cast flanges and flanged fittings shall be marked
with the ASTM specification,2 grade identification symbol (letters and numbers), and the melt number or melt identification. (b) Plate flanges, forged flanges, and flanged fittings shall be marked with the ASTM specification number and grade identification symbol.2 (c) A manufacturer may supplement these mandatory material indications with his trade designation for the material grade, but confusion of symbols shall be avoided. (d) For flanges and flanged fittings manufactured from material that meets the requirements of more than one specification or grade of a specification listed in Table 1A, see para. 4.2.8.
conformance to this Standard. The use of the prefix
ASME is optional.
4.2.5 Temperature. Temperature markings are not
required on flanges or flanged fittings; however, if marked, the temperature shall be shown with its corresponding tabulated pressure rating for the material. 4.2.6 Size. The NPS designation shall be marked on flanges and flanged fittings. Reducing flanges and reducing flanged fittings shall be marked with the applicable NPS designations as required by paras. 3.2 and 3.3. 4.2.7 Ring Joint Flanges. The edge (periphery) of each ring joint flange shall be marked with the letter R and the corresponding ring groove number.
4.2.3 Rating Designation. The flange or flanged fitting shall be marked with the number that corresponds to its pressure rating class designation (i.e., 150, 300, 400, 600, 900, 1500, or 2500).
4.2.8 Multiple Material Marking. Material for components that meet the requirements for more than one specification or grade of a specification listed in Table 1A may, at the manufacturers option, be marked with more than one of the applicable specification or grade symbols. These identification markings shall be placed so as to avoid confusion in identification. The multiple marking shall be in accordance with the guidelines set out in ASME Boiler and Pressure Vessel Code, Section II, Part D, Appendix 7.
4.2.4 Conformance. The designation B16 or B16.5
shall be applied to the flange or flanged fitting, preferably located adjacent to the class designation, to indicate 2 An ASME Boiler and Pressure Vessel Code, Section II specification number may be substituted for an ASTM specification number provided the requirements of the ASME specification are identical to or more stringent than the ASTM specification for the Grade, Class, or Type of material.
DIN 1626-84 WELDED CIRCULAR TUBES OF NON ALLOY STEELS WITH SPECIAL USt 37.0 - ST 37.0 - ST 44.0 - ST 52.0 - DIN1.0253 - 1.0254 1.0256 1.0256 1.0421 DIN1626-84
