Scribd
Upload
228 views

GSM Based Patient Monitoring System Using Flex Sensor

This document describes a hospital care system that uses embedded technology to continuously monitor patients' vital signs and send alerts via GSM mobile if parameters exceed alarm limits. The system takes readings for body temperature, blood pressure, heart rate, and respiration rate from sensors every minute and sends the data to a GSM device for recording. If a parameter goes outside the normal range, a message will be sent immediately to alert medical staff. The system is designed to help reduce nurse-to-patient ratios and speed response times in emergency situations.

Uploaded by

Jeevan Landge Patil
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
228 views

GSM Based Patient Monitoring System Using Flex Sensor

This document describes a hospital care system that uses embedded technology to continuously monitor patients' vital signs and send alerts via GSM mobile if parameters exceed alarm limits. The system takes readings for body temperature, blood pressure, heart rate, and respiration rate from sensors every minute and sends the data to a GSM device for recording. If a parameter goes outside the normal range, a message will be sent immediately to alert medical staff. The system is designed to help reduce nurse-to-patient ratios and speed response times in emergency situations.

Uploaded by

Jeevan Landge Patil
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 5

GSM BASED HOSPITAL CARE SYSTEM USING EMBEDDED

TECHNOLOGY
No PC interface, Updating of parameter after 01 min. If the parameter
exceeds alarm limits, MSG will be sent via GSM mobile. Like BP Out
limit etc.
INTRODUCTION:In bio-medical, in chemicals, pharmaceuticals and sugar,
many parameters are to be monitored. Depending upon the requirement the
number of channels, the number & type of sensor is decided.
In biomedical fields special are units are used, say
intensive care unit or coronary care unit. All of these units are designed to
offer the advantage of the low Nurse Patient ratio and concentration of the
equipment and the resources needed; to take care of critically ill or seriously
injured units.
In many of the Hospitals, in night shifts we find one or
two nurses carrying 50 to 80 patients at the same time. Most of the hospitals
have medical surgical emergency teams that rush to the scene of situation
that would be life threatening.
Most hospitals call this team by beeper annunciation or
public annunciation system. This emergency will respond the emergency
situation anywhere in the hospital, including the ICU.

A key factor in the success of the ICU is the information


that is available to the ICU is the information that is available to the shaft
providing information is the role of the technology and equipment.
In order to over-come all these difficulties we have
decided to complete our project on such as biomedical system which will
continuously monitor the body parameters of the patient under treatment.
The data will be sent to GSM for recording purpose &
stored there The system may be titled as Bio-medical data Recorder
System.
We have taken 4 bio-medical transducers and the relative
parameters say
- Body Temperature
- Blood pressure
- Heart rate monitoring
- Respiration rate.
Different types of transducers are used.
The block diagram of the system can be given as below.
EXPLANATION:As shown in block diagram, different types of
transducers are used for different parameters.
For body temperature, we use 2N2222 Transducer or
AD590.

The current across which is varying as per the changes in

temperature. These transducers output some electrical signals corresponding


to the body parameters.

B.P. Transducer also, outputs the mili volts signal


proportion, all to the blood pressure. Heart rate and the respiration rate are
the pulses to the micro controller through signal.
The output from the transducer is given to signal
conditioning block. In this block, the parameter is calibrated; so as to give it
to ADC. The ADC is 0808, 8 bit and having inbuilt multiplexer. Only two
input channels are used. As only BT and BP are analog parameters and HRate and respiration rate are the digital pulsing.
Being having inbuilt multiplexer the 0808 selects the
input channels automatically and the select lines are controlled by micro
controller itself.
The ADC data is given to micro controller through 8 bit
data bus.

The micro controller processes on this data and sends the

appropriate read out to the GSM through serial communication channel.


RS-232 is used for the micro controller and GSM
communication. All the four body parameters are shown on GSM screen in
tabular form.
Technical Specification:1)

Supply

= 230V AC, 50Hz.

2)

Logic

= Micro controller based 89C51.

3)

Display

= On LCD & mobile

4)

Language

= Assembly or C language.

5)

Parameters

= Body temp, blood pressure,


Respiration and heart rate.

6)

Communication

= Serial through RS-232.

Flex Sensor

Signal
conditioning

Signal
conditioning

Clock
Analog to
Digital
Converter
0808

CPU
89C51
SCL
Micro
Real
Controller SDA
Time

Signal
conditioning
PPm
RS 232
Serial
Interface
Signal
Conditioning
PPm

Regulated
Power Supply

+ 5 V DC
Ground

GSM mobile

*********

You might also like