Common Space Lighting Guidelines

DRAFT DO NOT CITE OR QUOTE DRAFT
Best Practices for Energy Efficient Lighting Page 1

Common Space Lighting
Guidelines
Best Practices for Efficiency

December 22, 2006
Drafted by
Benya Lighting Design
Commissioned by
UI and CL&P

Photo (left) courtesy Finelite (right) courtesy Lightolier

Introduction
Commercial buildings use about 50% of all the electricity consumed in the country for lighting.
Advances in state-of-the-art lighting technology can significantly reduce energy use and costs
while providing light levels and quality recommended by the Illuminating Engineering Society
of North America. In order to ensure compliance with applicable energy codes, achieve typical
lighting energy levels substantially less than the energy code allowance, and contribute to
regional energy and demand management, the following guidelines for office lighting are
strongly recommended. Note that these guidelines generally provide substantial benefits from
utility incentive programs and through LEED and other certification programs and may offer
significant tax deductions and other benefits.
Facilities Affected
These Guidelines are intended to be used by contractors, architects, engineers, and others
responsible for designing, specifying and/or building new lighting systems, including new
buildings, tenant fit-out, remodeling, and/or energy-upgrade initiatives.
In general, these Guidelines should be applied to the following:
Corridors
Restrooms
Lobbies
Conference rooms
Stairwells
Support space workrooms
Electrical and mechanical rooms
Facilities Less Affected
These Guidelines are not necessarily intended to address any of the following space types.
Office areas
Industrial and commercial manufacturing and assembly areas
Laboratories and other spaces with special requirements for lighting

However, the principles of cost effective, energy efficient design expressed by these Guidelines
should be employed in these or other space types whenever possible.
Implicit Considerations
These Guidelines were developed in consideration of applicable codes and standards in the U.S.,
including the following:
Standards of the Illuminating Engineering Society of North America, including
IESNA/ANSI RP-1, American National Standard for Office Lighting and the IESNA
Lighting Handbook, Ninth Edition. IESNA Standards apply in the USA, Canada and Mexico
Standards of Underwriters Laboratories.
Energy efficiency standards of the States of Connecticut, Massachusetts, and
IESNA/ASHRAE/ANSI 90.1-2001.
General Design Requirements
All designs must comply with applicable codes and ordinances. Note that in general, the
following requirements will result in lighting designs that demand less power (watts per square
foot floor area) than mandated by the energy code. The energy cost savings realized by this
practice will often pay back the incremental cost for the more efficient system within 3 years.
Additionally, in many cases the first cost of lighting may be less than traditional designs because
these Guidelines optimize the amount and type of lighting equipment than can be used.
Lighting Systems
General Requirements
A complete, hardwired lighting system must be installed complying with the following lighting
power density requirements:
a. Conference and meeting rooms and similar spaces shall not exceed a connected power
density of 1.0 watts per square foot.
b. Core areas including mailrooms, lunchrooms, restrooms, copy rooms, and similar spaces
shall not exceed a connected lighting power density of 0.7 watts per square foot.
c. Mechanical and electrical rooms shall not exceed 1.2 w/sf
d. Hallways, corridors, storage rooms, locker rooms and similar spaces shall not exceed a
connected power density of 0.6 watts per square foot.
e. Lobbies and Atriums should not exceed 1.0 watts per square foot.
f. Any other space not listed shall not exceed a connected power density of 0.5 watts per
square foot.
Compliance Documentation
Designs shall be certified using COM-CHECK 3.1 release 1 or higher. For the Code to be used,
select ASHRAE/IESNA 90.1-2004. If these guidelines are followed closely, the resulting designs
should achieve approximately 25-35% better than 90.1-2004 and 40-50% better than 90.1-2001.
NOTE: Achieving performance significantly better than these target values is very difficult and
not recommended without design involving considerable expertise.
Special Allowance for Decorative and Accent Lighting
Energy codes permit decorative and accent lighting and usually provide an additional power
allowance for them. Properly applied, these allowances can permit additional lighting power and
still permit a project to meet the energy code and other targets such as a LEED criterion.
However, for the purposes of this program, such additional power is not consistent with
exceptional energy efficiency.
In order to permit architects, interior designers, and lighting designers the ability to add lighting
for aesthetic effects or dcor, this program has chosen to limit the use of this added energy to 0.5
watts per square foot or the amount permitted by the code, whichever is less for restrooms,
lobbies, hallways and conference rooms only. The decorative lighting allowance can not be used
for any other common space.
Typical Lighting Systems
Most commercial buildings use conventional, generic lighting products. If chosen and used
properly, in general these lighting products can be very efficient as well as cost effective. A
good example is a 2 x 4 troffer with 2 or 3 T8 lamps. As described in the Office Lighting
Guideline, by using high performance lamps and ballasts and proper layouts, these lighting
systems can be extremely energy efficient.
However, too often these same luminaires are also used in hallways, lobbies and other areas.
This is usually not a good idea. While office areas are often lighted to 30-50 footcandles,
hallways are generally 10-15 footcandles and often less, and lobbies should be 20-30
footcandles. Using standard office lighting results in either overly bright hallways with too
much energy use, or spotty lighting. In other words, different lighting systems are needed for
many of these spaces.
Since these are finished spaces, its generally not acceptable to use bare lamp fixtures. The trick
is to find appealing and efficient fixtures with connected power in the range of 25-40 watts.
There are about a dozen generic lighting system types that should be considered. As a general
rule, pick luminaires that have at least 40% coefficient of utilization at 80/50/20 and RCR=7.

Lighting System Description Applications Information
Recessed Lighting Systems (grid and flanged)

2x 2 high performance
troffer with (2) F14T5
lamps and electronic
ballast. Choice of instant
start and program start
ballasts.
Maximum energy efficiency with
high efficiency instant start ballasts.
Power ranges from 27 watts (ballast
factor 0.90) to 34 watts (ballast
factor ~1.10). Typically 10% more
efficient than generic lens fixture.

1x 4 high performance
troffer with (1) F28T5
lamp and electronic ballast.
Choice of instant start and
program start ballasts.
Power 33-34 watts at 1.05 ballast
factor. About 10% more efficient
than generic lens fixture.

Generic lens 2x 2 troffer
with (2) F17T8 high
performance lamps and
electronic ballast. Choice
of instant start and program
start ballasts. High
efficiency ballasts are
available.
Use ballast factor to fine tune the
application. Watts range from 27
watts (.80 ballast factor) to 43 watts
(1.28 ballast factor). Maximum
energy efficiency with high
efficiency instant start ballasts.

Generic lens 1x 4 troffer
with (1) F32T8 high
performance lamps and
electronic ballast. Choice
of instant start or program
start ballast. High
efficiency ballasts are
available.
(1.37 ballast factor) with 1 lamp.
Maximum energy efficiency with
high efficiency instant start ballasts.
Surface Mounted Lighting Systems

Surface wall mounted
indirect luminaire with
single F32T8 lamp. Note:
must have light colored
walls (reflectance >60%)
to meet the efficiency
criterion of this section.
Must only be used in spaces with
light colored walls and ceilings. Use
ballast factor to fine tune the

Corridor wraparound with
(1) F32T8 lamp and high
efficiency electronic
ballast. Choice of instant
start and program start
ballasts. High efficiency
ballasts are available.
efficiency instant start ballasts. Use
these lights in most electrical and
mechanical rooms to prevent lamp
breaking.
Better quality lighting systems, somewhat less efficient

Recessed downlight with
(1) compact fluorescent 26
or 32 watt triple tube lamp.
In some cases an 18 watt
fixture may be acceptable.
Most of these fixtures permit the use
of 26, 32 or 42 watt lamps. Be wary
of using 42 watt lamps as spacing
can become quite large. Use ballast
factor carefully; for 26 watt lamps,
ballasts range from 26 watts
(BF~.95) to 29 watts (BF~1.10).
For 32 watt lamps, ballasts are
typically 36 watts at BF~1.0.

Surface downlight with (1)
compact fluorescent 26 or
32 watt triple tube lamp.
In some cases an 18 watt
fixture may be acceptable.
See above

Semi recessed downlight
with (1) compact
fluorescent 26 or 32 watt
triple tube lamp.
Most of these fixtures permit the use
of 26, 32 or 42 watt lamps. Be wary
of using 42 watt lamps as spacing
can become quite large. Use ballast
factor carefully; for 26 watt lamps,
ballasts range from 26 watts
(BF~.95) to 29 watts (BF~1.10).
Special Purpose Lighting (<0.40 CU at 80/50/10 RCR =7)

Surface mounted
vandalism resistant
luminaire with single
F32T8 lamp. About 20%
less efficient than normal
duty fixtures.

Vanity light for toilet
rooms. While many lamp
types are possible,
preference should be given
to fixtures that use T-8 or
T-5 lamps.
Limit the use of these fixtures to
toilet and bath vanities. Be aware of
the total fixture watts.

Surface wall mounted
sconce luminaire with 26
watt compact fluorescent
lamp.
Sconces are generally not an
efficient luminaire but provide a
reasonable amount of useful light.
Sconces with low wattage compact
fluorescent lamps can be used in
combination with downlights or
other higher-efficiency fixtures to
create an upscale appearance.

Undercabinet mounted task
light with single T8 lamp.
Available in 2, 3 and 4
lengths. Similar results
possible with F14T5,
F21T5 and F28T5 lamps.
Other lamps are less
efficient.
Use ballast to optimize this
installation. Use of a two level
(50%) ballast, hard wired to 50%
light, is generally recommended. In
this mode, a 3 fixture is only 16
watts and a 4 fixture is only 19
watts. For a 2 fixture, use a
reduced light output efficient ballast
for 14 watts.
Ballasts
General
In general, high power factor, low harmonic ballasts should be used for all fluorescent lighting.
Exceptions might be made for very low wattage lamps (<20 watts) as some of the more efficient
ballasts have high harmonics and/or low power factor. As long as only a few are used, the
impact will be minimal.
Ballast factor, on the other hand, is a variable. Ballast factor simply describes how much of the
rated light of the lamp is generated when the ballast is used. The efficiency stays about the same,
so the power goes up as the ballast factor goes up. For example, ballasts for F32T8 lamps are
typically rated as reduced light output (BF~.78, 24 watts per lamp), normal light output (BF~.88,
27 watts per lamp) or high light output (BF~1.15, 35 watts per lamp). A dimming ballast is
technically a variable ballast factor ballast. With many of these lighting situations, often the
secret of really low energy use it to employ a ballast with low ballast factor, or even to use of the
stepped ballasts (0-30-70-100 or 0-50-100) hard-wired in the low light position. There are a lot
of fluorescent applications where only 50% of the normal light is plenty.
Ballast starting type is another significant consideration. For compact fluorescent lamps, most
modern electronic ballasts are programmed start (PS), which exhibits a short starting delay but
permits may on/off cycles with minimum lamp life effects. For T-5 and T-8 lamps, you can
choose between program start and instant start (IS), which are more efficient and start the lamp
instantly, but will cause short lamp life with frequent switching. Most dimming ballasts are
rapid start (RS), a less efficient method of operation necessary to allow lamps to dim. Two level
ballasts are usually rapid start.
Because instant start ballasts are the most efficient and least costly, they should be used in all
longer duty cycle applications where the lights are turned on and off infrequently. Fluorescent
systems controlled by motion sensors in spaces where the lights will be turned on and off
frequently should employ program start ballasts. Stepped level and dimming electronic ballasts
may also be used as discussed below. T-8 fluorescent lighting systems should employ high
efficiency electronic ballasts.
Lamps
Designs should employ the following lamp types:
Generic Lamp Types Requirements Suppliers and Product Families
Four foot T-8 lamps*
F32T8
TCLP compliant (low mercury) lamps with
barrier coat and high lumen phosphor (minimum
3,100 initial lumens). Premium long life rated
lamps.
Sylvania XPS
Philips Advantage
GE HL
Fluorescent T-8 lamps
F17T8*, F25T8
TCLP compliant (low mercury) lamps with
barrier coat and high lumen phosphor. Premium
long life rated lamps. Minimum 1400 initial
lumens for F17T8 and 2200 initial lumens for
F25T8

Sylvania XPS
Philips ALTO TL8xx
GE SPX/ECO
*In some cases, the use of low wattage T-8 lamps may be warranted. These lamps are less energy efficient than
standard 32 watt high efficiency T-8 lamps, but in critical situations, they can be used to reduce power. Note that
these lamps are not fully compatible with all T-8 ballasts and applications. Among other issues, they are not
dimmable, and may take considerable time to warm up.

Fluorescent T-5 and T-
5HO lamps
F14T5, F21T5, and
F28T5

Standard T-5 lamps.
Sylvania Pentron
Philips Silhouette
GE T5
Compact fluorescent 4-
pin lamps
CF13, CF18, CF26, and
CF32,

Standard twin, quad, and triple tube lamps. Be
sure to use the four pin lamps as they operate
properly on electronic ballasts.
Sylvania Dulux
Philips PL
GE Biax
Application Notes
Hallways and Corridors
Note: Due to the high room cavity ratios of most corridors and similar narrow spaces, interior
finishes are critical. White ceilings and light colored walls are especially important; use deep
and saturated colors for accents only. Keep the floor reflectance as high as possible.
For general illumination, layouts should be between 0.45 and 0.55 W/SF. IESNA
recommendations are at least 5 footcandles, so all of the following meet minimum criteria. For
spaces with finished ceilings up to 10 feet, and assuming 80% ceiling reflectance, average wall
reflectance (including doors) of 50%, and floor reflectance of 20%, some of the possible lighting
systems and combinations include:
With high performance luminaires and T-8 or T-5 lamps,
light levels of 15-20 footcandles are possible.
With standard fluorescent fixtures and T-8 lamps, light
levels of 12-17 footcandles are possible.
With compact fluorescent downlights, light levels of 10-15
footcandles can be expected.
With a 50/50 mixture of compact fluorescent downlights and
sconces, light levels of 5-10 footcandles will likely result.
Indirect lighting can be used if the spaces are light colored
and the ceiling is a flat surface. Under ideal conditions, light
levels of 10-15 footcandles can occur, but generally expect
levels of 5-10 footcandles.
In the photos at left, the results of several lighting systems are
illustrated.
In the top photo, a corridor is lighted with compact
fluorescent downlights. The deep scallops of the downlight
create strong patterns on the wall. The result is very
dramatic. Care must be taken to keep downlights on equal
spacing and if possible, to create a lighting pattern that is
harmonious with the wall finish.
In the center photo, uplights are used to provide soft
illumination. The result is bright and even, but not dramatic.
This approach requires a sufficiently regular pattern of wall
space.
In the bottom photo, a combination of sconces and
downlights is used. This is a nice combination; this space
would be less glaring if the wall and ceiling finishes were
lighter.

Toilet Rooms
There are three areas to commercial toilet rooms; the entry
including a vestibule (if there is one); the vanity area; and the toilet
area. Mens rooms urinals are sometimes opposite the vanities, and
sometimes opposite the stalls.
The most common lighting design in these spaces addresses each
part separately:
The entry is lighted by downlights or sconces. See the top
photo at left. It is a good idea to place this lighting on a
24/7 emergency lighting circuit for safety and egress. All
the rest of the lighting can be controlled by time or motion
sensors.
The vanity is lighted by some combination of overhead
trough (top photo), sconces (top photo), and/or vanity lights
(middle photo). Try to avoid downlights because of deep
shadows on faces.
The wet wall behind the toilets can be lighted by a
continuous downlight slot, as in the bottom photo, by a
continuous uplight. Be sure to use reduced light output
ballasts in either of these techniques. Additional circulation
lighting can also use downlights, but be wary of cumulative
wattage. Remember, IESNA recommendations for the
circulation area are only 5 footcandles. Dont feel
compelled to over-light a toilet room circulation zone.
Design the toilet room for <0.8 watts per square foot, including the
vestibule and entry. Also, its acceptable to use up to 0.5 w/sf of
decorative allowance for sconces (top photo) when used in
conjunction with a regular lighting system. Nonetheless, low power
is not easy; for example, in the middle photograph, each vanity light
is 27 watts, so the total power of the three vanity lights 81 watts
uses the lighting power allowance for over 100 square feet. Take
full advantage of reduced power ballasts and even consider 13 and
18-watt compact fluorescent lamps in downlights and sconces.
Lobbies
Lobbies are expected to be dramatic and special. In addition to
general lighting, decorative and accent lighting is often part of the
design. The general lighting of the lobby can be performed at
about 0.8 w/sf using downlights, a very common solution. The
rest of the lighting involves a combination of decorative and accent
lighting. In order to stay within the 0.5 w/sf decorative lighting
allowance of these Guidelines, special lighting must also be
efficient.

The following luminaire types are generally recommended for these areas:
Wallwashers (photo, above). Compact fluorescent 26 or 32 watt lamps, or metal halide 20 or
39 watt lamps.
Art accent lights, 20 watt halogen IR MR16 fixtures or 20 watt ceramic metal halide MR16
or T4.5 lamp fixtures.
Sconces and chandeliers using 13, 18, and 24/27 watt twin tube and 13, 18, 26 and 32 watt
compact fluorescent lamps.

Even the most elaborate chandeliers are often available
with compact fluorescent or HID sources. For example,
in the photo at left, a chandelier using (4) 26 watt
compact fluorescent lamps illuminates a large lobby
area. While it may be tempting to use incandescent
chandeliers with screw-in compact fluorescent lamps,
energy code requirements make it necessary to seek out
and use decorative lighting with permanently-installed
ballasts and hardwired sockets for high efficacy sources.

To meet these guidelines, choose the appropriate
wattage lamps and be careful how many fixtures are
used. Because decorative luminaires are not often
efficient, use a combination of general lighting and
decorative lighting to meet both energy and lighting
goals.
Control Recommendations
By code, each interior space enclosed by ceiling high partitions must have separate local
switching and some form of automated-off control (occupancy sensing, time based scheduling,
or other). In addition, wherever possible, provide separate switching for lights in daylighted
zones.
Most public spaces are best equipped with a combination of time-of-day programmable
switching, backed up by motion sensor(s). Lights are energized for the normal operating time of
the building, and for the rest of the time, lights are turned on briefly when needed. This
minimizes cycling problems of just using motion sensors, and corresponds well to business
operations.
In buildings of limited occupancy or use, motion sensors can be used in restrooms and other
spaces with occasional use. Be use to use program start ballasts, and short lamp life wont occur.
And of course, for spaces with sufficient daylight, such as lobbies and atriums, use automatic
daylighting controls in addition to save the maximum amount of energy.
Controls for utility spaces like electrical and mechanical rooms require special consideration for
workers. In general, in small spaces where workers are unlikely to become trapped, motion
sensors are fine. But in larger spaces where motion sensors might not see the worker, use a
conventional wall switch for safety.
Photo courtesy Lightolier

An Efficient Core
This design uses a number of the elements discussed above. Light levels meet IESNA
recommendations for each space, and perhaps just as importantly, the design is attractive.
Consider providing emergency powered circuits to one downlight in each toilet room and one of
the two lights in the toilet corridor.

Common Space Lighting Guidelines

Uploaded by

Copyright:

Available Formats

Common Space Lighting Guidelines

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Common Space Lighting Guidelines

Uploaded by

Copyright:

Available Formats

DRAFT DO NOT CITE OR QUOTE DRAFT

Best Practices for Energy Efficient Lighting Page 1

You might also like