Laboratory Manual For Linear Electronics

Laboratory Manual for Linear Electronics 2

Laboratory Manual

for

Linear Electronics

by

James M. Fiore

Version 1.1, 13 May 2014


This Laboratory Manual for Linear Electronics, by James M. Fiore is copyrighted under the terms of
a Creative Commons license:

This work is freely redistributable for non-commercial use, share-alike with attribution

Published by James M. Fiore via dissidents

For more information or feedback, contact:

James Fiore, Professor
STEM Center
Mohawk Valley Community College
1101 Sherman Drive
Utica, NY 13501
[email protected]

or via www.dissidents.com

Cover art by the author
Introduction

This manual is intended for use in a linear semiconductor devices course and is appropriate for two and
four year electrical engineering technology curriculums. The manual contains sufficient exercises for a
typical 15 week course using a two to three hour practicum period. The topics cover basic diodes through
DC biasing and AC analysis of small signal bipolar and FET amplifiers along with class A and B large
signal analysis. For equipment, each lab station should include a dual adjustable DC power supply, a dual
trace oscilloscope, a function generator and a quality DMM. Some exercises also make use of a distortion
analyzer and a low distortion generator (generally, THD below 0.01%), although these portions may be
bypassed. For components, a selection of standard value watt carbon film resistors ranging from a few
ohms to a few megohms is required along with an array of typical capacitor values (film types
recommended below 1 F and aluminum electrolytics above). A decade resistance box and a 10 k
potentiometer may also be useful. Active devices include small signal diodes such as the 1N914 or
1N4148, the NZX5V1B or 1N751 zener, standard single LEDs, 2N3904 or 2N2222 NPN transistor,
2N3906 PNP transistor, and MPF102 N channel JFET.

Each exercise begins with an Objective and a Theory Overview. The Equipment List follows with space
provided for serial numbers and measured values of components. Schematics are presented next along
with the step-by-step procedure. Many exercises include sections on troubleshooting and design.
Simulations with Multisim are often presented as well, although any quality simulation package such as
PSpice can be used instead. All data tables are grouped together, typically with columns for the
theoretical and experimental results, along with a column for the percent deviations between them.
Finally, a group of appropriate questions are presented.

Other manuals in this series include DC and AC Electrical Circuits, Computer Programming with Python,
and Embedded Controllers Using C and Arduino.

A Note from the Author

This manual is used at Mohawk Valley Community College in Utica, NY, for our ABET accredited AAS
program in Electrical Engineering Technology. It was created out of a desire to offer an affordable lab
manual for our students which covered the requisite material and made optimal use of our laboratory
facilities. I am indebted to my students, co-workers and the MVCC family for their support and
encouragement of this project. While it would have been possible to seek a traditional publisher for this
work, as a long-time supporter and contributor to freeware and shareware computer software, I have
decided instead to release this using a Creative Commons non-commercial, share-alike license. I
encourage others to make use of this manual for their own work and to build upon it. If you do add to this
effort, I would appreciate a notification.

It doesnt matter how beautiful your theory is, it doesnt matter how smart you are. If it doesnt agree
with experiment, its wrong.

- Richard Feynman
Table of Contents

1. Diode Curves . . . . . 8
2. The Zener Diode . . . . . 14
3. Base Bias . . . . . . 20
4. LED Driver Circuits . . . . . 26
5. Voltage Divider Bias . . . . . 32
6. Emitter Bias . . . . . . 38
7. Feedback Biasing . . . . . 44
8. PNP Transistors . . . . . 50
9. Common Emitter Amplifier . . . . 56
10. Swamped CE Amplifier . . . . 62
11. Voltage Follower . . . . . 68
12. Class A Power Analysis . . . . 74
13. Class B Power Analysis . . . . 80
14. Power Amp with Driver . . . . 86
15. JFET Bias . . . . . . 92
16. JFET Amplifiers . . . . . 98

1
Diode Curves

Objective
The objective of this exercise is to examine the operation of the basic switching diode and to plot its
characteristic curve.

Theory Overview
The basic diode is an asymmetric non-linear device. That is, its current-voltage characteristic is not a
straight line and it is sensitive to the polarity of an applied voltage or current. When placed in forward
bias (i.e. positive polarity from anode to cathode), the diode will behave much like a shorted switch and
allow current flow. When reversed biased the diode will behave much like an open switch, allowing little
current flow. Unlike switch, a silicon diode will exhibit an approximate .7 volt drop when forward biased.
The precise voltage value will depend on the semiconductor material used. This volt drop is sometimes
referred to as the knee voltage as the resulting I-V curve looks something like a bent knee.

The effective instantaneous resistance of the diode above the turn-on threshold is very small, perhaps a
few ohms or less, and is often ignored. Analysis of diode circuits typically proceeds by determining if the
diode is forward or reversed biased, substituting the appropriate approximation for the device, and then
solving for desired circuit parameters using typical analysis techniques. For example, when forward
biased, a silicon diode can be thought of as a fixed .7 volt drop, and then KVL and KCL can be applied as
needed.

Equipment

(1) Adjustable DC Power Supply model:________________ srn:__________________
(1) Digital Multimeter model:________________ srn:__________________
(2) Signal diodes (1N4148, 1N914)
(1) 1 k resistor watt actual: ________________________
(1) 4.7 k resistor watt actual: ________________________

1N4148 Datasheet: http://www.fairchildsemi.com/ds/1N/1N4148.pdf

Schematics

Figure 1.1 Figure 1.2

Figure 1.3

Procedure

Forward Curve
1. Consider the circuit of Figure 1.1 using R = 1 k. For any positive value of E, the diode should be
forward biased. Once E exceeds the knee voltage, all of E (minus approximately .7 volts) drops across
R. Thus, as E increases, so does the diode current.

2. Build the circuit of Figure 1.1 using R = 1 k. Set E to 0 volts and measure both the diode's voltage
and current and record the results in Table 1.1. Repeat this process for the remaining source voltages
listed.

3. From the data collected in Table 1.1, plot the current versus voltage characteristic of the forward
biased diode. Make sure V
D
is the horizontal axis with I
D
on the vertical.

Reverse Curve
4. Consider the circuit of Figure 1.2 using R = 1 k. For any positive value of E, the diode should be
reversed biased. In this case, the diode should always behave like an open switch and thus no current
should flow. If no current flows, the voltage across R should be zero, and thus the diode voltage
should be equal to the applied source voltage. Note that the diode's voltage polarity is negative with
respect to that of Figure 1.1.

5. Build the circuit of Figure 1.2 using R = 1 k. Set E to 0 volts and measure both the diode's voltage
listed.

6. From the data collected in Table 1.2, plot the current versus voltage characteristic of the reverse
D
D
on the vertical.

Practical Analysis
7. Consider the circuit of Figure 1.3 using E = 12 volts, R1 = 10 k and R2 = 4.7 k. Analyze the
circuit using the ideal .7 volt forward drop approximation and determine the voltages across the two
resistors. Record the results in the first two columns of the first row (Variation 1) of Table 1.3.

8. Build the circuit of Figure 1.3 using E = 12 volts, R1 = 10 k and R2 = 4.7 k. Measure the voltages
across the two resistors. Record the results in columns three and four of the first row (Variation 1) of
Table 1.3. Also compute and record the percent deviations in columns four and five.

9. Reverse the direction of D1 and repeat steps 7 and 8 as Variation 2 in Table 1.3.

10. Return D1 to the original orientation and reverse the direction of D2. Repeat steps 7 and 8 as
Variation 3 in Table 1.3.

11. Reverse the direction of both D1 and D2, and repeat steps 7 and 8 as Variation 4 in Table 1.3.

Multisim
12. Repeat steps 7 through 11 using Multisim, recording the results in Table 1.4.

Data Tables

E (volts) VD ID
0
.5
1
2
4
6
8
10

Table 1.1

E (volts) VD ID
0
1
2
5
10
15

Table 1.2

Variation VR1 Theory VR2 Theory VR1 Exp VR2 Exp % Dev VR1 % Dev VR2
1
2
3
4

Table 1.3

Variation VR1 Multisim VR2 Multisim
1
2
3
4

Table 1.4

Questions

1. Is .7 volts a reasonable approximation for a forward bias potential? Is an open circuit a reasonable
approximation for a reverse biased diode? Support your arguments with experimental data.

2. The "average" resistance of a forward biased diode can be computed by simply dividing the diode's
voltage by its current. Using Table 1.1, determine the smallest average diode resistance (show work).

3. The instantaneous resistance (also known as AC resistance) of a diode may be approximated by
taking the differences between adjacent current-voltage readings. That is, r
diode
= V
diode
/I
diode
. What
are the smallest and largest resistances using Table 1.1 (show work)? Based on this, what would a
plot of instantaneous diode resistance versus diode current look like?

4. If the circuit of Figure 1.3 had been constructed with LEDs in place of switching diodes, would there
be any changes to the values measured in Table 1.3? Why/why not?

2
The Zener Diode

Objective
The objective of this exercise is to examine the operation of the zener diode and to plot its characteristic
curve.

Theory Overview
When forward biased, the zener diode behaves similarly to an ordinary switching diode, that is, it incurs a
.7 volt drop for silicon devices. Unlike a switching diode, the zener is normally placed in reverse bias. If
the circuit potential is high enough, the zener will exhibit a fixed voltage drop. This is called the zener
potential or V
Z
. Manufacturers specify this voltage with respect to the zener test current, or I
ZT;
a point
past the knee of the voltage-current curve. That is, if the zeners current is at least equal to I
ZT
, then its
voltage is approximately equal to the rated V
Z
. Above this current, even very large increases in current
will produce only very modest changes in voltage. Therefore, for basic circuit analysis, the zener can be
replaced mathematically by a fixed voltage source equal to V
Z
.

Equipment

(1) Zener diode around 5.1 volts (NZX5V1B, 1N751)

NZX5V1B Datasheet: http://www.nxp.com/documents/data_sheet/NZX_SER.pdf
1N751 Datasheet: http://www.fairchildsemi.com/ds/1N/1N751A.pdf

Schematics

Figure 2.1

Figure 2.2

Procedure

Forward Curve
1. Consider the circuit of Figure 2.1 using R = 2.2 k. For any positive value of E the zener is reverse
biased. Until the zener potential is reached, the diode resistance is effectively infinite and thus no
current flows. In this case the voltage across R is zero due to Ohms Law. Consequently, all of E
should appear across the zener. Once the source exceeds the zener voltage, the remainder of E (i.e. E
minus the zener potential) drops across R. Thus, as E increases, the circulating current increases but
the voltage across the zener remains steady.

2. Build the circuit of Figure 2.1 using R = 2.2 k. Set E to 0 volts and measure both the diode's voltage
listed.

3. From the data collected in Table 2.1, plot the current versus voltage characteristic of the forward
D
D
on the vertical.

Practical Analysis
4. Consider the circuit of Figure 2.2 using R1 = 2.2 k and R2 = 4.7 k. In general, to analyze circuits
like this, first assume that the zener is out of the circuit and then compute the voltage across R2 using
the voltage divider rule. If the resulting voltage is less than the zener potential then the zener is
inactive (high resistance) and does not affect the circuit. If, on the other hand, the resulting voltage is
greater than the zener potential then the zener is active and will limit the voltage across R2 to V
Z
. Via
KVL, the remainder of the voltage drops across R1 and from this the supply current may be
determined. This current will then split between R2 and the zener. The R2 current is found using
Ohms Law. The zener current is then found via KCL. Note that for higher and higher values of E, the
voltage across (and therefore the current through) R2 does not change. Instead, all of the excess
current from the source passes through the zener.

5. Build the circuit of Figure 2.2 using R1 = 2.2 k and R2 = 4.7 k. Set E to 2 volts. Compute the
theoretical diode voltage and current, and record them in the first row of Table 2.2. Then measure the
diode current and voltage and record in Table 2.2. Finally, compute and record the deviations.

6. Repeat step 5 for the remaining source voltages in Table 2.2.

Multisim
7. Repeat steps 5 and 6 using Multisim, recording the results in Table 2.3.

Data Tables

E (volts) VD ID
0
1
2
5
10
15
20

Table 2.1

E (volts) VD Theory ID Theory VD Exp ID Exp % Dev VD % Dev ID
2
5
10
15
20

Table 2.2

E (volts) VD Multsim ID Multisim
2
5
10
15
20

Table 2.3
Questions

1. Is it safe to assume that the voltage across a zener is always equal to the rated V
Z
? Why/why not?

2. The instantaneous resistance (also known as AC resistance) of a diode may be approximated by
taking the differences between adjacent current-voltage readings. That is, r
diode
= V
diode
/I
diode
. What
is the smallest effective resistance of the zener using Table 2.1 (show work)?

3. If the circuit of Figure 2.1 had been constructed with the zener reversed, how would this effect the
results recorded in Table 2.1?

4. Assume that a diode with a much higher I
ZT
rating (say, 100 mA) was used in this exercise. In
general, what would the likely outcome be for the circuit of Figure 2.2?
3
Base Bias: CE Configuration

Objective
The objective of this exercise is to explore the operation of a basic common emitter biasing configuration
for bipolar junction transistors, namely fixed base bias. Along with the general operation of the transistor
and the circuit itself, circuit stability with changes in beta is also examined.

Theory Overview
For a bipolar junction transistor to operate properly, the base-emitter junction must be forward biased
while the collector-base junction must be reverse biased. This will place V
BE
at approximately .7 volts and
the collector current I
C
will be equal to the base current I
B
times the current gain . For small signal
devices, the current gain is greater than 100 typically. Thus, I
C
>>I
B
and I
C
I
E
.

The common emitter configuration places the emitter terminal at ground. The base terminal is seen as the
input and the collector as the output. Using a fixed base supply, the base current is dependent on the value
of the base resistor via Ohms law. Consequently, any variation in current gain across a batch of
transistors will show up as an equivalent variation in collector current, and by extension, a variation in
collector-emitter voltage V
CE
.

Equipment

(1) Dual Adjustable DC Power Supply model:________________ srn:__________________
(3) Small signal NPN transistors (2N3904)


Schematics

Figure 3.1

Procedure

A Quick Check
1. A quick and easy way to determine if a transistor is damaged is through the use of the resistance (or
diode) function of a multimeter. The multimeter will produce a small current in order to determine the
connected resistance value. This current is sufficient to partially forward or reverse bias a PN
junction. Thus, for an NPN device, placing the red lead on the base and the black lead on the emitter
and collector in turn will produce forward bias on the junctions and the meter will show a low
resistance. Reversing the leads will create reverse bias and a high resistance will be indicated. If the
leads are connected from collector to emitter, one of the two junctions will be reverse biased
regardless of lead polarity, and thus, a high resistance is always indicated. Before proceeding to the
next step, check the three transistors using this method to ensure that they are functioning. (Note:
some multimeters include a beta checker function. This may also be used to determine if the
devices are good but the beta value produced should not be considered precise as the measurement
current and voltage are most likely different from the circuit in which the transistor will be used.)

Base Bias
2. Consider the circuit of Figure 3.1 with Vbb = 11V, Vcc = 15V, Rb = 330 k and Rc = 1.2 k. Assume
V
BE
= .7 volts. Further, assume that beta is 150 (a typical value for this device in this application).
Calculate the expected values of I
B
, I
C
and I
E
, and record them in the Theory columns of Table 3.1.
Note that the theoretical values will be the same for all three transistors.

3. Based on the expected value of I
C
, determine the theoretical value of V
CE
and record it in Table 3.2.
Also, fill in Table 3.2 with the typical (theoretical) beta value of 150.

4. Build the circuit of Figure 3.1 with Vbb = 11V, Vcc = 15V, Rb = 330 k and Rc = 1.2 k. Measure and
record the base, collector and emitter currents, and record them in the first row of Table 3.1.
Determine the deviations between the theoretical and experimental currents, and record these in Table
3.1.

5. Measure the base-emitter and collector-emitter voltages and record in the first row of Table 3.2.
Based on the measured values of base and collector current from Table 3.1, calculate and record the
experimental betas in Table 3.2. Finally, compute and record the deviations for the voltages and for
the current gain in Table 3.2.

6. Remove the first transistor and replace it with the second unit. Repeat steps four and five using the
second row of Tables 3.1 and 3.2.

7. Remove the second transistor and replace it with the third unit. Repeat steps four and five using the
third row of Tables 3.1 and 3.2.

Design
8. One way of improving the circuit of Figure 3.1 is to redesign it so that a single power supply may be
used. As noted previously, the base current is largely dependent on the value of V
BB
and R
B
. If the
supply is changed, the resistance can be changed by a similar factor in order to keep the base current
constant. This is just an application of Ohms law. Based on this, determine a new value for R
B
that
will produce the original I
B
if V
BB
is increased to the V
CC
value (i.e., a single power supply is used).
Record this value in Table 3.3.

9. Rewire the circuit so that the original R
B
is replaced by the new calculated value (the nearest standard
value will suffice). Also, the V
BB
supply should be removed and the left side of R
B
connected to the
V
CC
supply. Measure the new base current and record it in Table 3.3. Also determine and record the
deviation between the measured and target base current values.

Multisim
10. Build the original circuit in Multisim. Run a single simulation and record the I
B
, I
C
, I
E
and V
CE
values
in Table 3.4.

Data Tables

Transistor IB Theory IB Exp %D IB IC Theory IC Exp %D IC IE Theory IE Exp %D IE
1
2
3

Table 3.1

Transistor VBE Thry VBE Exp %D VBE VCE Thry VCE Exp %D VCE Theory Exp %D
1
2
3

Table 3.2

Calculated RB Actual RB Used IB Measured % Deviation IB

Table 3.3

IB Multisim IC Multisim IE Multisim VCE Multisim

Table 3.4

Questions

1. Are the basic transistor parameters borne out in this exercise? That is, are the approximations of
V
BE
=.7 and I
C
=I
E
valid?

2. Is the typical beta value of 150 highly accurate and repeatable?

3. Which circuit parameters are affected by beta changes? Which parameters appear to be immune to
changes in beta?

4. Comparing Tables 3.1 and 3.2, is there a notable pattern between the deviations for beta and collector
current? Why/why not?

5. In the circuit of Figure 3.1, what must R
B
be set to if V
BB
= 5V and the desired base current is 10 A?
4
LED Driver Circuits

Objective
The objective of this exercise is to examine two methods of driving LEDs with a constant current. Method
one involves a saturating switch while method two utilizes a non-saturating circuit.

Theory Overview
LEDs behave similarly to switching diodes in that they conduct current easily in forward bias and appear
as an approximate open circuit when reverse biased. Unlike standard silicon switching diodes, however,
the forward bias potential is not approximately .7 volts. Instead, this potential will vary depending on the
design of the LED but typically will be in the neighborhood of 2 volts for everyday devices. The
brightness of the LED is directly controlled by its current: the higher the current, the brighter the LED.
Consequently, it is important to drive LEDs with constant current sources to ensure consistent brightness.

Many circuits cannot drive LEDs directly so an intervening circuit is used (a driver) to boost the current
up to the value the LED requires for a given brightness. The driving signal is attached to the base while
the LED is situated in the collector, thus the transistors current gain, beta, is exploited. Unfortunately,
beta is not a particularly stable and consistent parameter so methods are required to alleviate this
shortcoming. A saturating switch works by operating at the extreme ends of the DC load line; that is,
either cutoff or saturation. If no signal is applied to the base, both base and collector currents will be zero,
and thus, the LED is off. When a base signal is applied, it is designed to be large enough to force the
transistor into saturation even with very modest betas. Therefore, the LED will always see the saturation
current, regardless of the normal beta value. In contrast, the non-saturating circuit works by placing a
resistor in the emitter. This establishes a constant emitter current (and thus, constant collector and LED
current) in spite of beta changes. That is, if beta changes, the effect is seen in the base current, not the
collector current. The non-saturating circuit has the advantage of using one less resistor, however, the
saturating switch has the greater advantage of using the same collector and base voltages (the non-
saturating circuit requires a collector source potential at least a few volts greater than the base voltage).

Equipment

(3) Small signal transistors (2N3904)
(1) LED
(1) 220 resistor watt actual: ________________________

Schematics

Figure 4.1


Procedure

Determining VLED
1. The forward potential of an LED depends on its design and the current flowing through it. The other
two circuits in this exercise are designed to produce LED currents of approximately 10 mA so a
determination of the forward potential of this particular diode at 10 mA is desired. Assemble the
circuit of Figure 4.1 using R = 470 , and E = 5 volts. Insert an ammeter in line with the LED.
Increase E until 10 mA is reached (the LED should be reasonably bright). Record the resulting LED
voltage in Table 4.1.

Saturating Switch
2. Consider the saturating switch of Figure 4.2 using Vcc = Vbb = 5 volts, Rb = 4.7 k and Rc = 220.
Calculate the base and collector currents and record them in the first row of Table 4.2 (theory). As the
circuit is in saturation, the theoretical V
CE
is close to zero and may be found on the transistor data
sheet via the V
CE
/I
C
saturation graph. Record this value in the first row of Table 4.2 as well.

3. Build the saturating switch of Figure 4.2 using Vcc = Vbb = 5 volts, Rb = 4.7 k and Rc = 220.
Measure and record the base and collector currents, and record the collector-emitter voltage in the
first row of Table 4.2 (experimental). Also compute and record the deviations between theory and
experimental results.

4. Remove the base resistor from Vbb and connect it to ground. Without a base source potential, the
circuit will be in cutoff. Determine the theoretical base and collector currents along with the collector-
emitter voltage and record them in the second row of Table 4.2. Measure these parameters, record
them in Table 4.2, and also compute and record the resulting deviations.

5. Reconnect the base resistor to the Vbb supply and swap in the second transistor. Repeat steps 3 and 4
using the next two rows of Table 4.2.

6. Reconnect the base resistor to the Vbb supply and swap in the third transistor. Repeat steps 3 and 4
using the final two rows of Table 4.2.

Non-saturating Current Source
7. Consider the non-saturating current source of Figure 4.3 using Vcc = 10 volts, Vbb = 5 volts and Re =
470. Using a typical beta of 150, calculate the base and collector currents, and the collector-emitter
voltage and record them in the first row of Table 4.3 (theory).

8. Build the non-saturating current source of Figure 4.3 using Vcc = 10 volts, Vbb = 5 volts and Re =
470. Measure and record the base and collector currents, and record the collector-emitter voltage in
the first row of Table 4.3 (experimental). Also compute and record the deviations between theory and

base current will be zero. Determine the theoretical base and collector currents along with the
collector-emitter voltage and record them in the second row of Table 4.3. Measure these parameters,
record them in Table 4.3, and also compute and record the resulting deviations.



Design
12. As seen in steps 7 through 11, the LED current of Figure 4.3 is a function of the base supply and the
emitter resistor. Determine a new value for the emitter resistance that will yield an LED current of 15
mA. Record this value in Table 4.4. Obtain a new resistor close in value to the calculated result and
swap it into the circuit. Measure the resulting LED current and record in Table 4.4.

Multisim
13. Simulate the circuit of Figure 4.2 and record the currents and voltage in Table 4.5.

14. Simulate the circuit of Figure 4.3 and record the currents and voltage in Table 4.6.

Data Tables

VLED

Table 4.1

Vbb IB Theory IC Theory VCE Theory IB Exp IC Exp VCE Exp % D IB % D IC % D VCE
5
0
5
0
5
0

Table 4.2

Vbb IB Theory IC Theory VCE Theory IB Exp IC Exp VCE Exp % D IB % D IC % D VCE
5
0
5
0
5
0

Table 4.3

Vbb RE Theory RE exp IC exp
5

Table 4.4

Vbb IB Multisim IC Multisim VCE Multisim
5
0

Table 4.5

Vbb IB Multisim IC Multisim VCE Multisim
5
0

Table 4.6

Questions

1. Do the two driver circuits produce a stable and predictable LED current in spite of changes in beta?

2. The circuit of Figure 4.2 is stated to be a saturating switch. How do the data of Table 4.2 confirm this
statement?

3. The circuit of Figure 4.3 is stated to be a non-saturating current source. How do the data of Table 4.3
confirm this statement?

5
Voltage Divider Bias

Objective
The objective of this exercise is to examine the voltage divider bias topology and determine whether or
not it produces a stable Q point. Various potential troubleshooting issues are also explored.

Theory Overview
One of the problems with simpler biasing schemes such as the base bias is that the Q point (I
C
and V
CE
)
will fluctuate with changes in beta. This will result in inconsistent circuit performance. A possible
solution is to attempt to place a fixed voltage across an emitter resistor. This will result in a stable emitter
current, and by extension, stable collector current and collector-emitter voltage. As beta varies, this
change will be reflected in a change in base current. With proper design, this change in base current will
have little overall impact on circuit performance. One method of obtaining a stable voltage across the
emitter resistor is to apply a stiff voltage divider to the base. Stiff, in this case, means that the current
through the divider resistors should be much higher than the current tapped off of the divider (the current
being tapped off is the base current). By doing so, variations in base current will not excessively load the
divider and this will lead to a very stable base voltage. The emitter voltage is one base-emitter drop less,
and is the potential across the emitter resistor. Hence, the emitter resistors voltage will be kept stable.

When troubleshooting, circuit faults often result in either shorted or open components. Typically this will
alter the circuit radically and push the Q point into either cutoff or saturation. The fault may also alter the
DC load line itself. Once the transistor goes into either cutoff or saturation, normal linear operation will
be lost.

Equipment


Schematic

Figure 5.1

Procedure

DC Load Line
1. Consider the circuit of Figure 5.1 using Vcc = 10 volts, R1 = 10 k, R2 = 3.3 k, Re = 4.7 k and
Rc = 5.6 k. Using the approximation of a lightly loaded stiff voltage divider, determine the ideal
end points of the DC load line and the Q point, and record these in Table 5.1.

Circuit Voltages and Beta
2. Continuing with the component values indicated in step one, compute the theoretical base, emitter
and collector voltages, and record them in Table 5.2 (Theory).

3. Build the circuit of Figure 5.1 using Vcc = 10 volts, R1 = 10 k, R2 = 3.3 k, Re = 4.7 k and Rc = 5.6 k.
Measure the base, emitter and collector voltages and record them in the first row of Table 5.2
(Experimental). Compute the deviations between theoretical and experimental and record these in the
first row of Table 5.2 (% Deviation).

4. Measure the base and collector currents and record these in the first row of Table 5.3. Based on these,
compute and record the experimental beta as well.

5. Swap the transistor with the second transistor and repeat steps 3 and 4 using the second rows of the
tables.

6. Swap the transistor with the third transistor and repeat steps 3 and 4 using the third rows of the tables.

Design
7. The collector current of the circuit can be altered by a variety of means including changing the emitter
resistance. If the base voltage is held constant, the collector current is determined by the emitter
resistance via Ohms Law. Redesign the circuit to achieve half of the quiescent collector current
recorded in Table 5.1. Obtain a resistor close to this value, swap out the original emitter resistor and
measure the resulting current. Record the appropriate values in Table 5.4.

Troubleshooting
8. Return the original emitter resistor to the circuit. Consider each of the individual faults listed in Table
5.5 and estimate the resulting base, emitter and collector voltages. Introduce each of the individual
faults in turn and measure and record the transistor voltages in Table 5.5.

Multisim
9. Build the circuit of Figure 5.1 in Multisim. Run a DC simulation and record the resulting transistor
voltages in Table 5.6.

Data Tables

VCE (Cutoff)
IC (Sat)
VCEQ
ICQ

Table 5.1

Transistor VB Thry VE Thry VC Thry VB Exp VE Exp VC Exp %D VB %D VE %D VC
1
2
3

Table 5.2

Transistor IB IC
1
2
3

Table 5.3

RE Theory RE Actual IC Measured

Table 5.4

Issue VB VE VC
R2 Short
RE Open
RC Short
RC Open
VCE Short
VCE Open

Table 5.5

VB Multisim
VE Multisim
VC Multisim

Table 5.6

Questions

1. Based on the results of Table 5.1, is the transistor operating in saturation, cutoff or in the linear
region?

2. Based on the results of Tables 5.2 and 5.3, does the circuit achieve a stable operating point when
compared to beta?

3. Based on the measurements of Table 5.5, is it possible for different circuit problems to produce
similar or even identical voltages in the circuit, or is every fault unique in its outcome?

4. What is the required design condition for the voltage divider bias to achieve high Q point stability in
spite of changes in beta?

5. Using the original circuit, determine a new value for the collector resistance that will yield a collector
voltage of approximately half of the power supply value.

6
Emitter Bias

Objective
The objective of this exercise is to examine the two supply emitter bias topology and determine whether
or not it produces a stable Q point. Various potential troubleshooting issues are also explored.

Theory Overview
A method of obtaining a stable Q point is to attempt to place a fixed voltage across an emitter resistor.
In the Voltage Divider bias this is achieved by applying a stiff voltage divider to the base. Alternately, a
negative supply may be attached to the low side of the emitter resistor instead of grounding it. The base is
then simply connected back to ground via a single resistor. If this base resistance is relatively small, the
base voltage will be close to zero as only the base current flows through it. Consequently, almost all of
the negative emitter supply will drop across the emitter resistor, with the exception of the single base-
emitter potential. As in the Voltage Divider circuit, this will result in a stable emitter current, and by
extension, stable collector current and collector-emitter voltage. As beta varies, this change will be
reflected in a change in base current. This can result in large percentage changes in base voltage;
however, the magnitude of the base potential will remain small, and thus, inconsequential.

Equipment


Schematic

Figure 6.1

Procedure

DC Load Line
1. Consider the circuit of Figure 6.1 using Vcc = 15 volts, Vee = -12 volts, Rb = 33 k, Re = 22 k and
Rc = 15 k. Using the approximation of a negligible base voltage, determine the ideal end points of
the DC load line and the Q point, and record these in Table 6.1.

2. Continuing with the component values indicated in step one, compute the theoretical emitter and
collector voltages, and record them in Table 6.2 (Theory). For the theoretical base voltage entry,
assume a beta of approximately 150 and determine the base current and voltage from the theoretical
collector current recorded in the Table 6.1.

3. Build the circuit of Figure 6.1 using Vcc = 15 volts, Vee = -12 volts, Rb = 33 k, Re = 22 k and Rc
= 15 k. Measure the base, emitter and collector voltages and record them in the first row of Table
6.2 (Experimental). Compute the deviations between theoretical and experimental and record these in
the first row of Table 6.2 (% Deviation).


tables.


Design
7. The collector voltage of the circuit can be altered by a variety of means including changing the
collector resistance. If the emitter supply and resistance are held constant, the collector voltage is
determined by the collector resistance and the collector supply. Redesign the circuit to achieve a
collector voltage of approximately 10 volts. Obtain a resistor close to this value, swap out the original
collector resistor and measure the resulting voltage. Record the appropriate values in Table 6.4.

Troubleshooting
8. Return the original collector resistor to the circuit. Consider each of the individual faults listed in
Table 6.5 and estimate the resulting base, emitter and collector voltages. Introduce each of the
individual faults in turn and measure and record the transistor voltages in Table 6.5.

Multisim
9. Build the circuit of Figure 6.1 in Multisim. Run a DC simulation and record the resulting transistor
voltages in Table 6.6.

Data Tables

VCE (Cutoff)
IC (Sat)
VCEQ
ICQ

Table 6.1

Transistor VB Thry VE Thry VC Thry VB Exp VE Exp VC Exp %D VB %D VE %D VC
1
2
3

Table 6.2

Transistor IB IC
1
2
3

Table 6.3

RC Theory RC Actual VC Measured

Table 6.4

Issue VB VE VC
RB Short
RB Open
RC Short
RC Open
RE Open
VCE Open

Table 6.5

VB Multisim
VE Multisim
VC Multisim

Table 6.6

Questions

1. Based on the results of Table 6.1, is the transistor operating in saturation, cutoff or in the linear
region?

2. Based on the results of Tables 6.2 and 6.3, does the circuit achieve a stable operating point when
compared to beta?

3. How does the Emitter Bias circuit compare to Base Bias and Voltage Divider Bias in terms of Q point
stability and complexity?

4. Using the original circuit, determine a new value for the emitter resistance that will yield half of the
quiescent collector current recorded in Table 6.1.
7
Feedback Biasing

Objective
The objective of this exercise is to examine two kinds of feedback biasing: collector feedback and emitter
feedback. Both forms potentially are more stable than simple base bias in terms of the impact of beta on
collector current.

Theory Overview
By inserting a resistor in either the emitter or collector portions of the transistor circuit, it is possible to
partially control the base current in such a way that an increase in beta will cause a decrease in base
current which in turn helps to mitigate the tendency of collector current to increase. This will result in
circuits that have greater Q point stability than simple base bias circuits although for certain practical
reasons they might not be as stable as voltage divider or dual supply emitter bias schemes.

In the collector feedback arrangement, the base resistor is connected from the collector to the base.
Therefore, its voltage is one base-emitter drop less than the collector voltage. The collector voltage, in
turn, is simply the supply potential minus the collector resistors drop. Therefore, as the collector current
rises, the collector resistors drop increases, forcing the collector voltage down and thus reducing the base
resistors voltage. By Ohms Law, this means that the base current must decrease. This decrease helps to
limit the overall increase in collector current.

The emitter feedback situation is similar. In this instance, as collector current increases the drop across the
emitter resistor rises. This will result in an increase in base voltage as it is locked to one base-emitter drop
above the emitter. Consequently, as the collector current increases, the voltage across the base resistor
decreases which helps to compensate for the original increase in collector current.

Equipment


Schematics


Procedure

Collector Feedback - DC Load Line
1. Consider the circuit of Figure 7.1 using Vcc = 12 volts, Rb = 220 k and Rc = 1 k. Determine the
ideal end points of the DC load line and the Q point, and record these in Table 7.1.


3. Build the circuit of Figure 7.1 using Vcc = 12 volts, Rb = 220 k and Rc = 1 k. Measure the base,
emitter and collector voltages and record them in the first row of Table 7.2 (Experimental).


tables.


Stability
7. Based on the measurements of Table 7.3, determine the maximum percent change of collector current
and record in Table 7.4. Also determine the maximum percent change of beta and record in Table 7.4.

Emitter Feedback - DC Load Line
8. Consider the circuit of Figure 7.2 using Vcc = 12 volts, Rb = 220 k, Re = 470 and Rc = 330 .
Determine the ideal end points of the DC load line and the Q point, and record these in Table 7.5.


10. Build the circuit of Figure 7.2 using Vcc = 12 volts, Rb = 220 k, Re = 470 and Rc = 330 .
(Experimental).


tables.


Stability
14. Based on the measurements of Table 7.7, determine the maximum percent change of collector current
and record in Table 7.8. Also determine the maximum percent change of beta and record in Table 7.8.

Troubleshooting
15. For the emitter feedback bias circuit, consider each of the individual faults listed in Table 7.9 and
estimate the resulting base, emitter and collector voltages. Introduce each of the individual faults in
turn and measure and record the transistor voltages in Table 7.9.

Data Tables

VCE (Cutoff)
IC (Sat)
VCEQ
ICQ

Table 7.1

Transistor VB Thry VE Thry VC Thry VB Exp VE Exp VC Exp
1
2
3

Table 7.2

Transistor IB IC
1
2
3

Table 7.3

%
% IC

Table 7.4

VCE (Cutoff)
IC (Sat)
VCEQ
ICQ

Table 7.5

1
2
3

Table 7.6

Transistor IB IC
1
2
3

Table 7.7

%
% IC

Table 7.8

Issue VB VE VC
RB Open
RE Open
RE Short
RC Open
RC Short
VCE Open

Table 7.9
Questions

1. Based on the results of Tables 7.4 and 7.8, do these circuits achieve a stable operating point when
compared to beta?

2. Which circuit is more stable in this exercise; the emitter feedback bias or the collector feedback bias?
Is it safe to say that this will always be the case for any emitter feedback bias circuit versus any
collector feedback bias circuit?

3. Are the transistor voltages always as stable as the collector current or can they be more or less stable?

4. Based on the collector current equation derivations for the two circuits, derive the collector current
equation for a combination circuit which consists of a collector feedback bias circuit with an emitter
resistor added.

8
PNP Transistors

Objective
The objective of this exercise is to investigate the practical differences between circuits implemented with
PNP transistors versus NPN transistors. PNP versiosn of basic biasing and LED driver circuits will be
used.

Theory Overview
On a practical level, PNP transistors may be thought of as a mirror image of their NPN counterparts. That
is, all of the device's voltage polarities and current directions will be opposite of those found with NPNs.
In fact, a simple way to turn an NPN circuit into an equivalent PNP circuit is to swap out the transistor
and then flip the polarity of the power supply (or supplies, as the case may be). The resulting circuit will
produce essentially the same voltages and currents as the original but with reversed polarities. By no
means are negative power supplies a requirement to use PNPs, though. Commonly, the circuit is "flipped
top to bottom" and implemented with a positive supply. In this case the emitter will be found toward the
top and the collector toward the bottom. In some instances this orientation may also reverse the
operational logic of the circuit. For example, the "flipped" PNP LED driver becomes an inverting driver.
That is, a logic low will light the LED instead of a logic high.

Equipment

(3) Small signal PNP transistors (2N3906)
(1) LED


Schematics


Procedure

PNP Voltage Divider
1. Consider the circuit of Figure 8.1 using Vcc = 10 volts, R1 = 10 k, R2 = 3.3 k, Re = 4.7 k and
Rc = 5.6 k. Using the approximation of a lightly loaded stiff voltage divider, determine the
theoretical base, emitter and collector voltages, and record them in Table 8.1 (Theory).

2. Build the circuit of Figure 8.1 using Vcc = 10 volts, R1 = 10 k, R2 = 3.3 k, Re = 4.7 k and Rc = 5.6 k.
(Experimental).

3. Swap the transistor with the second transistor and repeat steps 1 and 2 using the second row of the
table.

4. Swap the transistor with the third transistor and repeat steps 1 and 2 using the third row of the table.

Troubleshooting
5. Consider each of the individual faults listed in Table 8.2 and estimate the resulting base, emitter and
collector voltages. Introduce each of the individual faults in turn and measure and record the
transistor voltages in Table 8.2.

PNP LED Driver
6. Consider the PNP saturating switch of Figure 8.2 using Vcc = Vbb = 5 volts, Rb = 4.7 k and Rc =
220. Calculate the base and collector currents and record them in the first row of Table 8.3 (Theory).
As the circuit is in saturation, the theoretical V
CE
is close to zero and may be found on the transistor
data sheet via the V
CE
/I
C
saturation graph. Record this value in the first row of Table 8.3 as well.

7. Build the saturating switch of Figure 8.2 using Vcc = Vbb = 5 volts, Rb = 4.7 k and Rc = 220.
Measure and record the base and collector currents, and record the collector-emitter voltage in the
first row of Table 8.3 (Experimental). Also compute and record the deviations between theory and

circuit will be in cutoff. Determine the theoretical base and collector currents along with the collector-
emitter voltage and record them in the second row of Table 8.3. Measure these parameters, record
them in Table 8.3, and also compute and record the resulting deviations.



Design
11. A simple way to program the LED current in the driver is by altering the collector resistor. First,
measure the LED potential while it is lit. Assuming that the collector-emitter saturation voltage is
neglible, all of the power supply voltage will drop across the collector resistor when the LED is lit,
with the exception of the LED voltage. Ohm's Law can then be used to determine a resistance value
for a desired target current. Compute the required value of resistance to achieve an LED current of 8
mA. Replace the collector resistor with the nearest value available and measure the resulting current.
Record the appropriate values in Table 8.4.

Data Tables

1
2
3

Table 8.1

Issue VB VE VC
R2 Short
RE Open
RC Short
RC Open
VCE Short
VCE Open

Table 8.2

Vbb IB Theory IC Theory VCE Theory IB Exp IC Exp VCE Exp
5
0
5
0
5
0

Table 8.3

RC Theory RC Actual IC Measured

Table 8.4
Questions

1. Is the PNP voltage divider circuit as stable as its NPN counterpart studied earlier?

2. Compare the NPN voltage divider lab results to this PNP version. If the various transistor voltages are
added together (e.g., NPN base voltage plus PNP base voltage), a constant results. What is the
significance of this value and will it always work out in this fashion? Why/why not?

3. Do the troubleshooting faults presented in the PNP circuit produce similar transistor voltages
compared to the same faults in the NPN version of the circuit? Why/why not?

4. How does the operational logic of the PNP LED driver compare to the NPN version of the same
circuit?

5. Are the LED current design considerations the same as those of the NPN version?

9
Common Emitter Amplifier

Objective
The objective of this exercise is to examine the characteristics of a common emitter amplifier, specifically
voltage gain, input impedance and output impedance. A method for experimentally determining input and
output impedance is investigated along with various potential troubleshooting issues.

Theory Overview
An ideal common emitter amplifier simply multiples the input function by a constant value while also
inverting the signal. The voltage amplification factor, A
v
, is largely a function of the AC load resistance at
the collector and the internal emitter resistance, r
e
. This internal resistance is, in turn, inversely
proportional to the DC emitter current. Therefore, if the underlying bias is stable with changes in beta, the
voltage gain will also be stable. The circuit will appear as an impedance to the signal source, Z
in
. This
impedance is approximately equal to the base biasing resistor(s) in parallel with the impedance seen
looking into the base (Z
in(base)
) which is approximately equal to r
e
. Consequently, the amplifiers input
impedance may experience some variation with beta. In contrast, the circuits output impedance as seen
by the load is approximately equal to the DC collector biasing resistor.

From a practical standpoint, input and output impedance cannot be measured directly with an ohmmeter.
This is because ohmmeters measure resistance by sending out a small sensing current. The DC bias and
AC signal currents will interact with this current and produce an unreliable result. Instead, impedances
can be measured indirectly through a voltage divider effect. That is, if the voltages of both legs of a
voltage divider can be measured and the resistance of one of the legs is known, the remaining resistance
may be determined using Ohms Law or the voltage divider rule.

Equipment

(1) Dual Channel Oscilloscope model:________________ srn:__________________
(1) Function Generator model:________________ srn:__________________
(2) 10 F capacitors actual: ________________________
(1) 470 F capacitor actual: ________________________

Schematics

Figure 9.1

Figure 9.2

Procedure

DC Circuit Voltages
1. Consider the circuit of Figure 9.1 using Vcc = 15 volts, Vee = -12 volts, Rs = 10 k, Rb = 33 k, Re
= 22 k, Rc = 15 k, Rload = 20 k, C1 = C2 = 10 F and C3 = 470 F. Using the approximation of
a negligible base voltage, determine the DC voltages at the base, emitter, and collector along with the
collector current, and record these in Table 9.1.

2. Build the circuit of Figure 9.1 using Vcc = 15 volts, Vee = -12 volts, Rs = 10 k, Rb = 33 k, Re =
22 k, Rc = 15 k, Rload = 20 k, C1 = C2 = 10 F and C3 = 470 F. Make sure that the AC
source is turned off or disconnected. Measure the DC voltages at the base, emitter, and collector along
with the collector current, and record these in Table 9.1. Note, you may wish to use a transistor curve
tracer or beta checker to get approximate values of beta for each of the three transistors to be used.

AC Circuit Voltages
3. Based on the calculated collector current, determine the resulting theoretical r
e
, A
v
, Z
in
and Z
out
, and
record these in Table 9.2. Assume a beta of approximately 150 for the Z
in
calculation.

4. Continuing with the values in Table 9.2 and using an AC source voltage of a 40 mV peak-peak 1 kHz
sine wave, compute the theoretical AC base, emitter and load voltages, and record them in Table 9.3
(Theory). Note that R
s
will create a voltage divider effect with Z
in
, thus reducing the signal that
reaches the base. This reduced signal is then multiplied by the voltage gain and appears at the
collector.

5. Set the source to a 40 mV peak-peak 1 kHz sine wave and apply to the circuit. Using the oscilloscope,
place one probe at the base and the second at the emitter. Record the resulting peak-peak voltages in
the first row of Table 9.3 (Experimental). The oscilloscope inputs should be set for AC coupling with
the bandwidth limit engaged. Capture an image of the oscilloscope display.

6. Move the second probe to the load and record its peak-peak value in the first row of Table 9.3. Also
include whether the signal is in phase or out of phase with the base signal. Capture an image of the
oscilloscope display.

7. Unhook the load resistor from the output capacitor and measure the resulting collector voltage (do not
connect the output capacitor to ground-simply leave it dangling). Record this value in the final
column of Table 9.3.

8. Reattach the load resistor. Swap the transistor with the second transistor and repeat steps 5 through 7
using the second row of Table 9.3.

9. Reattach the load resistor. Swap the transistor with the third transistor and repeat steps 5 through 7
using the third row of Table 9.3.

10. Using the measured base and collector voltages from Table 9.3, determine the experimental gain for
each transistor. From these gains determine the experimental r
e
. Using the source voltage, the
measured base voltages and the source resistance, determine the effective input impedances via
Ohms Law or the voltage divider rule. Finally, in similar manner and using the loaded and unloaded
collector voltages along with the load resistor value, determine the experimental output impedances.
Record these values in Table 9.4. Also determine and record the percent deviations.

Troubleshooting
11. Return the load resistor to the circuit. Consider each of the individual faults listed in Table 9.5 and
estimate the resulting AC load voltage. Introduce each of the individual faults in turn and measure
and record the load voltage in Table 9.5.

Multisim
12. One issue with amplifiers is noise and ripple on the power supply. This will be directly coupled to
output of the circuit via the collector resistor. Worse, this noise or ripple may be coupled into the base
and then amplified along with the desired input signal. This can be an issue with amplifiers that use a
voltage divider bias. One way to reduce this effect is to decouple the voltage divider from the base.
This modification is shown in the circuit of Figure 9.2. Cb effectively shorts R2, sending power
supply noise and ripple to ground instead of into the base. By itself this would also short the desired
input signal so an extra resistor, R3 is added between the capacitor and the base. The input impedance
of the circuit is approximately equal to R3 in parallel with r
e
. To show the effectiveness of this
technique, build the circuit of Figure 9.2 in Multisim. Use Vin = 20 mV peak at 1 kHz, Vripple = 20
mV peak at 120 Hz, Vcc = 12 volts, Rs = 1 k, R1 = 10 k, R2 = 3.3 k, R3 = 22 k, Re = 4.7 k,
Rc = 3.3 k, Rload = 1 k, Cin = Cout = 10 F, Cb= 100 F and Ce = 470 10 F. Run a Transient
simulation and look at the load voltage. A very small low frequency variation should be noted. This is
the 120 Hz ripple coupled in through the collector resistor. Alter the circuit by removing Cb and R3 to
produce the basic voltage divider circuit (or more simply, set Cb and R3 to extremely small values
such as pF and m). Rerun the simulation. The load voltage should now show a much more obvious
ripple contribution, thus showing how effective the power supply decoupling components can be.

Data Tables

VB Thry VE Thry VC Thry IC Thry VB Exp VE Exp VC Exp IC Exp

Table 9.1

re Av Zin Zout

Table 9.2

Transistor VB Thry VE Thry VL Thry VB Exp VE Exp VL Exp Phase VL VL No Load
1
2
3

Table 9.3

Transistor Av Exp re Exp Zin Exp Zout Exp %D Av %D re %D Zin %D Zout
1
2
3

Table 9.4

Issue VLoad
RB Short
C1 Open
RC Short
RC Open
RE Open
C2 Open
C3 Open
VCE Open

Table 9.5

Questions

1. Does the common emitter amplifier produce a considerable amplification effect and if so, are the
results consistent across transistors?

2. Does the common emitter amplifier produce a phase shift at the output and if so, is it affected by the
transistor beta?

3. If the collector and base voltages had been measured with the oscilloscope DC coupled, how would
the measurements of Table 9.3 have changed?

4. Does the value of the transistor beta play any role in setting the input impedance? Was a considerable
variation in input impedance apparent?
10
Swamped CE Amplifier

Objective
The objective of this exercise is to examine the characteristics of a swamped common emitter amplifier,
specifically the effects of swamping on voltage gain, input impedance and distortion.

Theory Overview
As the signal current changes in a transistor, the total current flowing through the emitter changes along
with it. As a result, these changes produce small changes in r
e
which in turn changes the voltage gain. In
other words, the gain changes throughout the signal producing slightly more or less gain at some points
along the signal than others. These changes show up as a squashing or elongating of the positive and
negative peaks of the output signal. Generally, these forms of waveform distortion are to be avoided.
Also, they tend to worsen as the output signal amplitude increases. A method of mitigating this distortion
is to add AC resistance to the emitter portion of the circuit. This added resistance tends to buffer or
swamp out the changes in r
e
and therefore reduces the distortion. A side bonus is that Z
in(base)
will also
be increased which will result in an increased Z
in
to the circuit. On the downside, the added resistance will
lower the voltage gain. Consequently the swamped amplifier exhibits a lower gain but one of higher
quality. In general, the larger the swamping resistance is compared to r
e
, the greater the effects on
distortion, gain and input impedance.

Equipment

(1) Low Distortion Function Generator model:________________ srn:__________________
(1) Distortion Analyzer model:________________ srn:__________________
(1) Small signal transistor (2N3904)

Schematic

Figure 10.1

Procedure

AC Circuit Voltages
1. Consider the circuit of Figure 10.1 using Vcc = 15 volts, Vee = -12 volts, Rs = 10 k, Rb = 33 k,
Re = 22 k, Rsw1 = 220 , Rsw2 = 1 k, Rc = 15 k, Rload = 20 k, Cin = Cout = 10 F and
Ce=470 F. Using the approximation of a negligible DC base voltage, determine the DC collector
current and r
e
, and record these in Table 10.1. Using the r
e
, calculate the expected Z
in
, Z
in(base),
and A
v

for the X, Y and Z connection points for Ce (shown at position X in the schematic). Record these in
Table 10.2. If a transistor curve tracer or beta checker is not available to get an approximate value of
beta for the transistor, estimate it at 150.

2. Build the circuit of Figure 10.1 using Vcc = 15 volts, Vee = -12 volts, Rs = 10 k, Rb = 33 k,
Re=22 k, Rsw1 = 220 , Rsw2 = 1 k, Rc = 15 k, Rload = 20 k, Cout = Cout = 10 F and
Ce=470F. Connect Ce to postion X. Disconnect the signal source and check the DC transistor
voltages to ensure that the circuit is biased correctly. (Note, the DC equivalent circuit is very similar
to the ones used in Exercises 6 and 9, and should exhibit similar DC voltage readings.)

3. Using a 1 kHz sine wave setting, apply the signal source to the amplifier and adjust it to achieve a
load voltage of 2 volts peak-peak.

4. Measure the AC peak-peak voltages at the source, the base, and the load, and record these in Table
10.3. The load waveforms may exhibit some asymmetry due to distortion so be sure to record the
peak-peak voltage not the peak. If asymmetry is observed between the positive and negative peaks,
make a note of it. Also, capture images of the oscilloscope displays (V
s
with V
b
and V
b
with V
load
).

5. Set the distortion analyzer to 1 kHz and % total harmonic distortion (% THD). Apply it across the
load and record the resulting reading in the final column of Table 10.3.

6. Remove the distortion analyzer and connect Ce to position Y instead of X. Repeat steps 3, 4 and 5.

7. Remove the distortion analyzer and connect Ce to point Z instead of Y. Repeat steps 3, 4 and 5.

8. Using the measured base and load voltages from Table 10.3, determine the experimental gain for each
transistor. Using the measured source and base voltages along with the source resistance, determine
the effective input impedances via Ohms Law or the voltage divider rule. Record these values in
Table 10.4. Also determine and record the percent deviations.

Multisim
9. Build the circuit in Multisim and run three sets of simulations, one for each of the three Ce positions.
For each trial, set the AC source voltage to the value measured in Table 10.3 (V
S Exp
). Run a Transient
Analysis and inspect the voltages at the base and load. The AC source voltage may have to be
adjusted slightly to achieve the desired the desired 2 volt peak-peak load voltage. Record these values
in Table 10.5. Add the Distortion Analyzer instrument at the load and record the resulting value.

Data Tables

IC
re

Table 10.1

Position Av Theory Zin(Base) Theory Zin Theory
X
Y
Z

Table 10.2

Position VS Exp VB Exp VL Exp % THD
X
Y
Z

Table 10.3

Position Av Exp Zin Exp %Dev Av %Dev Zin
X
Y
Z

Table 10.4

Position VS Multisim VB Multisim VL Multisim % Distortion
X
Y
Z

Table 10.5
Questions

1. In summary, what are the effects of swamping?

2. Is the change in voltage gain directly proportional to the amount of swamping?

3. Is the change in input impedance directly proportional to the amount of swamping?

4. Is the change in distortion directly proportional to the amount of swamping?

5. Are THD levels below 1% easily discerned on a simple oscilloscope display?

6. Why is it important that the load voltage be set to the same value in each of the three trials instead of
setting the source to the same value?

11
Voltage Follower

Objective
The objective of this exercise is to examine the characteristics of a voltage follower, specifically an
emitter follower using a Darlington pair. Voltage gain, input impedance and distortion will all be
examined.

Theory Overview
The function of a voltage follower is to present a high input impedance and a low output impedance with
a non-inverting gain of one. This allows the load voltage to accurately track or follow the source voltage
in spite of a large source/load impedance mismatch. Ordinarily this mismatch would result in a large
voltage divider loss. Consequently, followers are often used to drive a low impedance load or to match a
high impedance source. While typical laboratory sources exhibit low internal impedances, some circuits
and passive transducers can exhibit quite high internal impedances. For example, electric guitar pickups
can exhibit in excess of 10 k at certain frequencies. Although the voltage gain may be approximately
one, current gain and power gain can be quite high, especially if a Darlington pair is used. Besides unity
voltage gain and a high Z
in
and low Z
out
, followers also tend to exhibit low levels of distortion.

The Darlington pair effectively produces a beta times beta effect by feeding the emitter current of one
device into the base of a second transistor. This also produces the effect of doubling both the effective
V
BE
and r
e
.

Equipment

Schematic

Figure 11.1

Procedure

1. Consider the circuit of Figure 11.1 using Vcc = 5 volts, Vee = -12 volts, Rs = 22 k, Rb = 470 k,
Re = 1 k, Rload = 220 , Cin = Ce = 10 F and Ce = 470 F. Using the approximation of a
negligible DC base voltage, determine the DC collector current and r
e
, and record these in Table
11.1. Using the r
e
, calculate the expected Z
in
, Z
in(base),
Z
out
and A
v
. Record these in Table 11.2. If a
transistor curve tracer or beta checker is not available to get an approximate value of beta for the
transistors, estimate the pair at 10,000.

2. Build the circuit of Figure 11.1 using Vcc = 5 volts, Vee = -12 volts, Rs = 22 k, Rb = 470 k,
Re=1k, Rload = 220 , Cin = Ce = 10 F and Ce = 470 F. Disconnect the signal source and check
the DC transistor voltages to ensure that the circuit is biased correctly. (Note: The base should be
close to zero while the emitter will be two V
BE
drops less, or about -1.4VDC.)

source voltage of 2 volts peak-peak (i.e., to the left of Rs).

4. Measure the AC peak-peak voltages at the source, the base, and the load, and record these in Table
11.3. Also note the phase of the load voltage compared to the source. If distortion asymmetry is
observed between the positive and negative peaks, make a note of it. Also, capture images of the
oscilloscope displays (V
s
with V
b
and V
b
with V
load
).

5. Set the distortion analyzer to 1 kHz and % total harmonic distortion (% THD). Apply it across the
load and record the resulting reading in Table 11.3.

6. Finally, unhook (i.e., open) the load and measure the resulting load voltage. Record this in the final
column of Table 11.3.

7. Using the measured base and load voltages from Table 11.3, determine the experimental gain for the
circuit. Using the measured source and base voltages along with the source resistance, determine the
effective input impedance via Ohms Law or the voltage divider rule. In similar fashion, using the
loaded and unloaded load voltages along with the load resistance, determine the effective output
impedance. Record these values in Table 11.4. Also determine and record the percent deviations.

Troubleshooting
8. Return the load resistor to the circuit. Consider each of the individual faults listed in Table 9.5 and
estimate the resulting AC load voltage. Introduce each of the individual faults in turn and measure
and record the load voltage in Table 9.5.

Multisim
9. Build the circuit in Multisim and run a Transient Analysis. Use a 1 kHz 1 volt peak sine for the
source. Inspect the voltages at the source, base and load. Record these values in Table 11.6. Add the
Distortion Analyzer instrument at the load and record the resulting value.

Data Tables

IC
re

Table 11.1

Av Theory Zin(Base) Theory Zin Theory Zout Theory

Table 11.2

VS Exp VB Exp VL Exp Phase VL % THD VL No Load

Table 11.3

Av Exp Zin Exp Zout Exp %Dev Av %Dev Zin %Dev Zout

Table 11.4

Issue VLoad
Rb Short
Cin Open
Re Open
Ce Open
RLoad Short
VCE Open
VCC Open

Table 11.5

VS Multisim VB Multisim VL Multisim % Distortion

Table 11.6

Questions

1. Would the results of this exercise have been considerably different if the load had been ten times
larger? What does that say about the performance of the circuit?

2. If the 22 k source had been directly connected to the 220 load without the follower in between, what
would be the load voltage?

3. How do the THD levels of the follower compare to those of the swamped common emitter amplifier?

4. How would the circuit parameters change if a Darlington pair had not been used?
12
Class A Power Analysis

Objective
The objective of this exercise is to examine large signal class A operation. A voltage follower will be
investigated by plotting the AC load line and determining output compliance, maximum load power,
supplied DC power and efficiency. The effects of clipping will be noted.

Theory Overview
The maximum output signal, or compliance, of a class A amplifier is determined by its AC load line. The
maximum peak level is determined by the smaller of V
CEQ
and I
CQ
r
Load
. If either of these levels is hit, the
output signal will begin to clip causing greatly increased distortion. Knowing this voltage and the load
resistance, the maximum load power may be determined. Dividing this power by the total supplied DC
power will yield the efficiency. The maximum theoretical efficiency of an RC coupled class A amplifier
is 25% although real-world circuits may be far less. In fact, the power dissipation of the transistor itself
(P
DQ
) may be greater than the maximum load power, clearly not a desirable condition. Note that the total
supplied power is the product of the total supplied voltage and the average total current. In a class A
amplifier that is not clipping, the average supplied current is equal to the quiescent DC current. In the case
of a dual supply emitter biased circuit, this is simply the collector current and can be measured with a DC
ammeter.

Equipment

Schematic

Figure 12.1

Procedure

AC Load Line and Power Analysis
1. Consider the circuit of Figure 12.1 using Vcc = 5 volts, Vee = -12 volts, Rb = 470 k, Re = 1 k,
Rload = 100 , Cin = Cout = 10 F and Ce = 470 F. Determine the theoretical I
CQ
, V
CEQ
, V
CE(Cutoff)

and I
C(Sat)
. and record these in Table 12.1. It will be helpful to plot the AC load line for the next step.

2. Build the circuit of Figure 12.1 using Vcc = 5 volts, Vee = -12 volts, Rb = 470 k, Re = 1 k,
Rload=100 , Cin = Cout = 10 F and Ce = 470 F. Disconnect the signal source and measure the
DC transistor voltages to ensure the circuit is biased correctly. Record V
CEQ
and I
CQ
in Table 12.1
(Experimental).

3. Based on the data recorded in Table 12.1, determine the theoretical maximum unclipped load voltage
(compliance) and record it in Table 12.2. Based on this, determine the maximum load power and
record it Table 12.2 as well. Also determine and record the expected values for the quiescent power
dissipation of the transistor (P
DQ
), the supplied DC current and power, and the resulting efficiency.

load voltage that just begins to clip. Reduce the amplitude slightly to produce a clean, unclipped
wave. Record this level as the experimental compliance in Table 12.2. From this, determine and
record the experimental maximum load power. Also, capture an image of the oscilloscope display.
5. Insert an ammeter in the collector and measure the resulting current with the signal still set for
maximum unclipped output. Record this in Table 12.2 as I
supplied
(Experimental).

6. Using the data already recorded, determine and record the experimental P
DQ
, P
Supplied
, and . Finally,
determine the deviations for Table 12.2.

Clipping and Distortion
7. Increase the signal until both peaks begin to clip. Record these clipping levels in Table 12.3. Make
sure the oscilloscope is DC coupled for this measurement as any offset is important. Compare these
peaks to those predicted by the AC load line. Also, capture an image of the oscilloscope display.

8. Decrease the signal level so that it is about 90% of the maximum unclipped level. Set the distortion
analyzer to 1 kHz and % total harmonic distortion (% THD). Apply it across the load and record the
resulting reading in Table 12.4 (Normal). Increase the signal by about 20% so that one of the peaks is
obviously clipped and take a second distortion reading, recording it Table 12.4 (Clipped).

Multisim
source. Inspect the voltage at the load. Record the peak clip points in Table 12.5. Reduce the input
signal so that clipping disappears. Add the Distortion Analyzer instrument at the load and record the
resulting value.

Data Tables

Theory Experimental
ICQ
VCEQ
IC(Sat) X
VCE(Cutoff) X

Table 12.1

Theory Experimental % Deviation
Compliance
PLoad(max)
ISupplied
PDQ
PSupplied

Table 12.2

Positive Clip
Negative Clip

Table 12.3

%THD Normal
%THD Clipped

Table 12.4

Positive Clip Negative Clip % Distortion

Table 12.5
Questions

1. Does the maximum load power compare favorably to the supplied DC power and the transistors
power dissipation? That is, is the circuit efficient?

2. How does the THD level of the clipped signal compare to that of the unclipped signal?

3. How well do the clip levels measured and simulated compare to the predicted AC load line?

4. How would the circuit performance change if a Darlington pair had not been used? Would this affect
the AC load line?

5. Would increasing the Vcc supply increase the output compliance? Why/why not?

13
Class B Power Analysis

Objective
The objective of this exercise is to examine large signal class B operation. A voltage follower will be
investigated to determine output compliance, maximum load power, supplied DC power and efficiency.
The effects of crossover distortion will be noted by comparing resistor and diode biasing schemes.

Theory Overview
The maximum output signal, or compliance, of a class B amplifier is determined by its AC load line. The
peak to peak compliance is roughly equal to the total DC supply voltage(s). As two output devices are
used, each conducting for half of the cycle, the quiescent current can remain low, unlike a class A
amplifier. This results in vastly improved efficiency, theoretically up to 78.5%. The switchover from one
transistor to the other is problematic and can result in crossover or notch distortion. To alleviate this, the
transistors are given a small idle current so that each base-emitter junction is just about fully on. While
resistors can be used to create this bias, trying to match the linear current-voltage characteristic of a
resistor to the logarithmic characteristic of a PN junction is tricky. Consequently, another PN junction,
namely a diode, is used instead. The diode will result in a more stable circuit which produces less notch
distortion.

Equipment

(1) Small signal NPN transistor (2N3904)
(1) Small signal PNP transistor (2N3906)
(2) Switching diodes (1N914 or 1N4148)
(2) 220 resistors watt actual: ________________________
(2) 2.2 k resistors watt actual: ________________________
Schematics

Figure 13.1

Figure 13.2


Figure 13.3

Procedure

Resistor Versus Diode Bias and Crossover Distortion
1. Consider the circuit of Figure 13.1 using Vcc = 6 volts, R1 = R2 = 2.2 k, R3 = R4 = 220 ,
Rload=100 , C1 = C2 = 10 F and C3 = 100 F. Ideally, this circuit will produce a compliance of
just under 6 volts peak-peak.

2. Build the circuit of Figure 13.1 using Vcc = 6 volts, R1 = R2 = 2.2 k, R3 = R4 = 220 ,
Rload=100, C1 = C2 = 10 F and C3 = 100 F. Disconnect the signal source and insert an ammeter
into the collector of Q1. Record I
CQ
in Table 13.1.

3. Connect the signal source and apply a 1 kHz sine at 2 volts peak. Look at the load voltage and capture
the oscilloscope image. There should be considerable notch or crossover distortion.

4. Cycle through the remaining supply voltages in Table 13.1, repeating steps 2 and 3. Only images of
the first and last trials need be captured. As the bias current increases, the notch distortion should
decrease.

5. Replace R3 and R4 with switching diodes, as shown in Figure 13.2. Repeat steps 2 through 4 using
this circuit and Table 13.2. Overall, the superior matching of the diodes to the transistors should result
in decreased notch distortion.

Dual Supply and Power Analysis
6. Add the negative power supply so that the circuit now appears as Figure 13.3. Set the supplies to +/- 6
volts DC. This should produce similar bias and amplification results to the single 12 volt supply
circuit of Figure 13.2. Although the output coupling capacitor is no longer needed (one advantage of
the dual supply topology), leave it in for safety sake.

7. Based on the I
CQ
recorded for the 12 volt supply in Table 13.2, determine the theoretical P
DQ
. Also
determine the expected compliance, P
Load(max)
, I
supplied
, P
supplied
and efficiency. Record these values in
the Theoretical column of Table 13.3.

8. Apply the signal source to the amplifier and adjust it to achieve a load voltage that just begins to clip.
Reduce the amplitude slightly to produce a clean, unclipped wave. Record this level as the
experimental compliance in Table 13.3. From this, determine and record the experimental maximum
load power. Also, capture an image of the oscilloscope display.

9. Insert an ammeter in the collector and measure the resulting current with the signal still set for
maximum unclipped output. Record this in Table 13.3 as I
supplied
(Experimental). Remove the
ammeter.

10. Using the data already recorded, determine and record the experimental P
DQ
, P
Supplied
, and . Finally,
determine the deviations for Table 13.3.

Distortion
11. Unlike class A distortion which gets worse as the signal increases, notch distortion is relatively fixed.
Therefore, it represents a smaller percentage of the overall output signal as the signal increases. To
see this effect, adjust the signal level to achieve a load voltage of 10 volts peak-peak. There should be
no clipping. Set the distortion analyzer to 1 kHz and % total harmonic distortion (% THD). Apply it
across the load and record the resulting reading in Table 13.4 (10 Vpp). Decrease the generator to
achieve a load voltage of 2 volts peak-peak and record the resulting THD.

Multisim
source. Inspect the voltage at the load. Record the peak clip points in Table 13.5. Reduce the input
signal so that clipping disappears. Add the Distortion Analyzer instrument at the load and record the
resulting value.

Data Tables

Supply ICQ - Resistors
6 V
8 V
10 V
12 V

Table 13.1

Supply ICQ - Diodes
6 V
8 V
10 V
12 V

Table 13.2

Theory Experimental % Deviation
Compliance
PLoad(max)
ISupplied
PDQ
PSupplied

Table 13.3

%THD 10 Vpp
%THD 2 Vpp

Table 13.4

Positive Clip Negative Clip % Distortion

Table 13.5

Questions

1. Does the maximum load power compare favorably to the supplied DC power and the transistors
power dissipation? That is, is the circuit efficient? How does it compare to class A operation
(Exercise 12)?

2. How is the notch distortion affected by the power supply?

3. Compare the resistor bias and diode bias circuits regarding idle current (I
CQ
) and notch distortion.
Compute the I
CQ
versus V
CC
stability (I
CQ-MAX
/ I
CQ-MIN
) of each circuit using the first and last entries
of Tables 13.1 and 13.2.

4. How does the class B circuit distortion compare to class A operation (Exercise 12)?

5. Would increasing the Vcc supply increase the output compliance? Why/why not?

14
Power Amp with Driver

Objective
The objective of this exercise is to examine a typical audio amplifier consisting of a class A driver feeding
a class B follower. System gain and clipping limits will be examined along with the audibility of clipping
distortion and the shapes of voice waveforms.

Theory Overview
Typical audio amplifiers utilize one or more small signal class A stages to achieve sufficient voltage gain
which then feeds a class B power stage connected to the load (normally a loudspeaker). The stage
preceding the power section is referred to as the driver stage or simply the driver. The driver is often
directly coupled instead of coupled via a capacitor. This maximizes gain and reduces component count.

A typical loudspeaker exhibits a nominal 8 impedance. As such, it demands considerable current. The
job of the class B follower is to create a good match to this low impedance and produce sufficient current
and power gain to drive it effectively. The voltage gain comes from the prior stages. If any of the
amplifier stages clip the waveform, the loudspeaker will reproduce the distorted wave. This distortion can
be clearly audible and produce a signal that sounds fuzzy or harsh. Loudspeakers can also be used as
microphones (although the quality will not be as high as that achieved with a properly designed
microphone). In this experiment, a loudspeaker will be used as a microphone to inspect the waveshapes
produced by the human voice; waveshapes that are potentially far more complex than simple sine waves.

Equipment

(2) Small signal NPN transistors (2N3904)
(1) Small signal PNP transistor (2N3906)
(2) Switching diodes (1N914 or 1N4148)
(1) 1 k potentiometer or decade box
(1) 8 or 16 general purpose loudspeaker

Schematic

Figure 14.1

Procedure

Bias, Gain and Compliance
1. Consider the circuit of Figure 14.1 using Vcc = 6 volts, Vee = -6 volts, R1 = 6.8 k, R4 = 1 k,
R3=100 , Rload = 100 , Cin = 1 F and Cout = 100 F. R2 is an adjustable resistance (pot or
decade box). For proper bias, the emitters of the output transistors should be at 0 volts DC. For this to
be true there must be Vcc-Vbe or approximately 5.3 volts across R4. Ignoring base currents, this
establishes I
CQ
of transistor 1 which in turn creates a potential drop across R3. From this the voltage
across R2 may be determined. Knowing the value of R1 and the total supply presented, Ohms law or
the voltage divider rule may be used to compute the require setting for R2. Compute the required
value for R2 and record it in Table 14.1.

2. Compute the gain of the driver stage. For the load of Q1, the dynamic resistance of the diodes is small
enough to ignore. Also, assume the current gain of the output transistors is approximately 100.
Remember, only one output transistor is on at any given time. The gain of the class B stage may be
assumed to be unity. Record the theoretical circuit gain in Table 14.1.

3. Ideally, the class B stage will produce a compliance of just under 6 volts peak. It may be less than this
as the driver stage might clip sooner. Compute the AC load line for the driver stage and determine its
compliance. Note that there will be a voltage divider effect between Re and the load of Q1 which will
reduce the compliance from that calculated via the load line. Record the theoretical compliance value
in Table 14.1. It should be less than that of the output stage and thus represents the compliance of the
entire circuit.

4. Build the circuit of Figure 14.1 using Vcc = 6 volts, Vee = -6 volts, R1 = 6.8 k, R4 = 1 k,
R3=100, Rload = 100 , Cin = 1 F and Cout = 100 F. Set the pot or decade box (R2) to the value
calculated in Table 14.1. Disconnect the signal source and inspect the DC voltage at the load. Adjust
R2 until this voltage goes to 0 volts. Record the resulting value of R2 in Table 14.1.

5. Connect the signal source and apply a 1 kHz sine at .2 volts peak. Inspect the load and source
voltages with the oscilloscope and capture an image of the pair. From these voltages determine the
circuit gain and record it in Table 14.1.

6. Increase the signal level until the output begins to clip. Reduce the level until the signal is undistorted
and record the resulting load voltage as the experimental compliance in Table 14.1.

Waveforms: Human Perception and Production
7. Turn down the signal source to about 100 mV peak. Insert the loudspeaker in series with the load
resistor. Accidentally placing it in parallel will cause excessive current draw and likely destroy the
output transistors (after making a particularly loud and irritating squawk). Gradually turn up the
signal level while monitoring the load voltage with the oscilloscope. Listen to the sound change as the
amplifier begins to clip. Describe this change in Table 14.2. Repeat this with the other frequencies
indicated.

8. Remove the loudspeaker and function generator. Reposition the loudspeaker so that it acts as the
signal source (i.e., in the original position of the generator). It will now act as a microphone. While
examining the load voltage, speak into the loudspeaker and note the typically complex waveshapes.
Try holding a few different vowel sounds at different pitches and capture a few of these images.
Ordinarily it is difficult for humans to vocalize pure sine waves, however, complex waveforms can be
broken down mathematically into a combination of sine waves of differing frequencies, amplitudes
and phases. As this is a linear amplifier, superposition holds, and thus if the circuit response to
individual sines at differing frequencies can be determined then the response to complex waves such
as the human voice and musical instruments can also be determined.

Troubleshooting
9. Remove the loudspeaker and return the generator to the circuit. Consider each of the individual faults
listed in Table 14.3 and estimate the resulting DC and AC load voltages. If the DC voltage moves a
great deal off of zero, chances are the AC load voltage will be badly distorted and there is no need to
attempt to estimate a precise value. Introduce each of the individual faults in turn and measure and
record the load voltages in Table 14.3.

Data Tables

Theory Experimental
R2
Av
Compliance

Table 14.1

Frequency Observations
1 kHz

500 Hz

200 Hz

Table 14.2

Issue VLoad DC VLoad AC
R2 Short
Cin Open
R1 Open
R3 Open
D1 Short
D2 Open
Cout Open
VCE Open

Table 14.3

Questions

1. Is the maximum output compliance determined solely by the class B output stage?

2. What kinds of distortion are present in this circuit?

3. Calculate the maximum load power and load current of the amplifier if the loudspeaker had
accidentally been placed in parallel with the load resistor rather than in series.

4. How do the values calculated in Question 3 compare to the data sheet maximums for the 2N3904/6?

15
JFET Bias

Objective
The objective of this exercise is to examine three methods to bias JFETs and determine which produce a
stable Q point. A method of determining I
DSS
and V
GS(OFF)
in the lab is also presented.

Theory Overview
Unlike bipolar junction transistors, FETs do not have a fixed forward biased junction potential. This
makes bias analysis a little trickier. It is often useful to have a couple of device parameters on hand,
namely I
DSS
and V
GS(OFF)
. As is the case with BJTs, finding the main current (I
D
) is the key to finding all
other circuit currents and voltages. One convenient aspect of JFETs is that the gate current can be ignored
for most bias applications. Self Bias may be analyzed through the use of a Self Bias curve or through an
iterative process of estimation of V
GS
leading to drain currents via Ohms law and the general FET
transconductance equation. Self Bias tends to have modestly stable Q points. Source Bias is an
improvement over Self Bias. It tends to swamp out V
GS
variation via the addition of a negative source
bias voltage. This topology also turns out potentially to have a very stable transconductance although it is
not examined in this exercise. Finally, Current Source Bias utilizes a BJT to establish a very stable drain
current. This turns out this comes at the expense of a stable V
GS
and transconductance (again, not
examined here), so this form of bias is not necessarily the best choice for all applications.

Equipment

(3) Small signal JFETs (MPF102)
(1) Small signal BJT (2N3904)

MPF102 Datasheet: http://www.onsemi.com/pub_link/Collateral/MPF102-D.PDF
Schematics



Procedure

Determining IDSS and VGS(OFF)
1. Consider the circuit of Figure 15.1 using Vdd = 15 volts and Vgg = 0 volts. With nothing else in the
circuit, the resulting drain current should equal I
DSS
. Similarly, if Vgg is gradually changed to a value
negative enough to drop the drain current to zero, Vgg must be equal to V
GS(OFF)
.
2. Build the circuit of Figure 15.1 using Vdd = 15 volts and Vgg = 0 volts. Insert an ammeter in the
drain and record the resulting current in Table 15.1. Slowly increase the magnitude of Vgg (i.e., make
it more negative) until the drain current drops to zero (as a practical point, try to get it under 10 A,
or as low as the ammeter will allow). Record this voltage in Table 15.1. Repeat this process for the
other two transistors. Be sure not to confuse the JFETs. Keep them in order.

Self Bias
3. Consider the circuit of Figure 15.2 using Vdd = 15 volts, Rg = 330 k, Rd = 4.7 k, and Rs =2.2 k.
Using the values of Table 15.1, calculate and record the expected voltages for JFET 1 in Table 15.2.
Also record the expected drain current in Table 15.3.

4. Build the circuit of Figure 15.2 using Vdd = 15 volts, Rg = 330 k, Rd = 4.7 k, and Rs = 2.2 k.
Measure and record the voltages for JFET 1 in Table 15.2. Based on V
D
, compute and record the
experimental drain current in Table 15.3. Also determine and record the drain current deviation.

5. Repeat steps 2 and 3 for the second and third JFETs.

Source Bias
6. Consider the circuit of Figure 15.3 using Vdd = 15 volts, Vss = -3 volts, Rg = 330 k, Rd = 4.7 k
and Rs = 4.7 k. A reasonable approximation for V
GS
in this circuit is -2 volts DC. Based on this,
calculate and record the expected voltages for JFET 1 in Table 15.4. Also record the expected drain
current in Table 15.5.

7. Build the circuit of Figure 15.3 using Vdd = 15 volts, Vss = -3 volts, Rg = 330 k, Rd = 4.7 k and
Rs = 4.7 k. Measure and record the voltages for JFET 1 in Table 15.4. Based on V
D
, compute and
record the experimental drain current in Table 15.4. Also determine and record the drain current
deviation.


Current Source Bias
9. Consider the circuit of Figure 15.4 using Vdd = 15 volts, Vee = -5 volts, Rg = 330 k, and Rd = Rs =
4.7 k. Calculate and record the expected voltages for JFET 1 in Table 15.6. Also record the
expected drain current in Table 15.7.

10. Build the circuit of Figure 15.3 using Vdd = 15 volts, Vee = -5 volts, Rg = 330 k, and Rd = Rs = 4.7
k. Measure and record the voltages for JFET 1 in Table 15.6. Based on V
D
, compute and record the
experimental drain current in Table 15.7. Also determine and record the drain current deviation.

Data Tables

JFET IDSS VGS(OFF)
1
2
3

Table 15.1

JFET VG Thry VS Thry VD Thry VG Exp VS Exp VD Exp
1
2
3

Table 15.2

JFET ID Theory ID Experimental %Dev ID
1
2
3

Table 15.3

1
2
3

Table 15.4

1
2
3

Table 15.5

1
2
3

Table 15.6

1
2
3

Table 15.7

Questions

1. Of the three biasing forms presented, which produces the most stable and predictable drain current?

2. Does the precise value of beta for the BJT in the final circuit matter that much? Why/why not?

3. In general, identify two ways of decreasing the drain voltage in the circuit of Figure 15.3.

4. In general, identify two ways of increasing the drain current in the circuit of Figure 15.4.


16
JFET Amplifiers

Objective
The objective of this exercise is to examine common source and common drain (voltage follower) JFET
amplifiers. Both voltage gain and input impedance will be investigated.

Theory Overview
In many regards, JFET amplifiers share similar attributes with their bipolar counterparts. Superficially,
they look very similar as well. The main functional differences are that JFET based amplifiers tend to
have higher input impedances but tend to offer lower voltage gains. Further, without swamping, JFET
amplifiers tend to produce lower levels of distortion. As with r'
e
impacting bipolar circuit performance,
JFET performance is impacted by the transsconductance, g
m
. Like the bipolar common emitter amplifier,
the common source amplifier exhibits a voltage gain greater than one with inversion. The source follower,
like the bipolar emitter follower, shows a voltage gain just under one with no inversion.

Equipment

(1) Small signal JFET (MPF102)
Schematics

Figure 16.1

Figure 16.2
Procedure

Common Source Voltage Amplifier
1. Consider the circuit of Figure 16.1 using Vdd = 15 volts, Vss = -3 volts, Rin = 33 k, Rg = 330 k,
Rs = 4.7 k, Rd = 4.7 k, Rload = 22 k, Cin = Cout = 10 F and Cs = 470 F. Assuming V
GS
= -2
volts and g
m
= 2 mS, determine the theoretical gain and input impedance of the circuit and record
these in Table 16.1.

2. Build the circuit of Figure 16.1 using Vdd = 15 volts, Vss = -3 volts, Rin = 33 k, Rg = 330 k,
Rs=4.7 k, Rd = 4.7 k, Rload = 22 k, Cin = Cout = 10 F and Cs = 470 F. Set Vin to a 100 mV
peak sine at 1 kHz. Measure the voltages at the gate and load, and record these in Table 16.1. Capture
images of the input and gate voltages, and the gate and load voltages. Note whether or not the load is
inverted compared to the gate signal.

3. Based on the measured gate and drain voltages, determine the resulting theoretical A
v
and Z
in
, and
record these in Table 16.1. Note that Zin may be computed using the voltage divider rule or Ohm's
law given the gate and input voltages along with the input resistor value. Also determine and record
the percent deviations.

4. Repeat steps 1 through 3 for the remaining two JFETs.

Common Drain Voltage Follower
5. Consider the circuit of Figure 16.2 using Vdd = 15 volts, Vss = -3 volts, Rin = 33 k, Rg = 330 k,
Rs = 4.7 k, Rload = 22 k, Cin = 10 F and Cout = 470 F. Assuming V
GS
= -2 volts and g
m
= 2
mS, determine the theoretical gain and input impedance of the circuit and record these in Table 16.2.

6. Build the circuit of Figure 16.2 using Vdd = 15 volts, Vss = -3 volts, Rin = 33 k, Rg = 330 k,
Rs=4.7 k, Rload = 22 k, Cin = 10 F and Cout = 470 F. Set Vin to a 100 mV peak sine at 1 kHz.
Measure the voltages at the gate and load, and record these in Table 16.2. Capture images of the input
and gate voltages, and the gate and load voltages. Note whether or not the load is inverted compared
to the gate signal.

7. Based on the measured gate and drain voltages, determine the resulting theoretical A
v
and Z
in
, and
record these in Table 16.2. Also determine and record the percent deviations.

8. Repeat steps 5 through 7 for the remaining two JFETs.

Troubleshooting
9. Consider each of the individual faults listed in Table 16.3 and estimate the resulting AC load voltage
for circuit 16.1. Introduce each of the individual faults in turn and measure and record the load
voltage in Table 16.3.

Data Tables

JFET Av Thry Zin Thry Vg Exp Vd Exp Av Exp Zin Exp %Dev Av %Dev Zin
1
2
3

Table 16.1

JFET Av Thry Zin Thry Vg Exp Vs Exp Av Exp Zin Exp %Dev Av %Dev Zin
1
2
3

Table 16.2

Issue VLoad
Rg Short
Cin Open
Rd Short
Rd Open
Rs Open
Cout Open
Cs Open
VDS Open

Table 16.3
Questions

1. Does the common source amplifier produce a considerable amplification effect and if so, are the
results consistent across transistors?

2. Does the common source amplifier produce a phase shift at the load? How does this compare with the
common drain follower?

3. How do the voltage gains of these circuits compare to their bipolar versions?

4. How do the input impedances of these circuits compare to their bipolar versions?

Laboratory Manual For Linear Electronics

Uploaded by

Copyright:

Available Formats

Laboratory Manual For Linear Electronics

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Laboratory Manual For Linear Electronics

Uploaded by

Copyright:

Available Formats

What is the manual about and what topics does it cover?

What equipment is needed to complete the experiments in the manual?

Laboratory Manual for Linear Electronics 2

Laboratory Manual for Linear Electronics 3

You might also like