Saudi Arabia Concrete Products (SACOP)

Products Guide
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
1
app.
08
07
06
05
04
03
02
01
1 General 2
2 Introduction 3
3 Advantages and Specications 3
3.1 Advantages 3
3.2 Specifications 3
4 Production Process 4
4.1 Batching and mixing of concrete materials 4
4.2 Reinforcement (cage) Fabrication 4
4.3 Dry Cast Process 4
4.4 Wet Cast Process 5
4.5 Steam Curing 5
5 Products 6
5.1 Storm Drain Pipe 6
5.2 Reinforced Concrete Sewer Pipe with Lining 7
5.3 Reinforced Concrete Jacking Pipe (RCJ Pipes) 8
5.4 Reinforced Concrete Manholes and Inspection Chambers 10
6 Pipe design 12
6.1 Joint Deflection 13
6.2 Types of Joints 14
7 Quality Standards 14
8 Underground Installations for Buried Pipe 15
8.1 Introduction 15
8.2 Unloading and Handling 15
8.3 Rubber Gaskets 15
8.4 Trench 16
8.5 Foundations 16
8.6 Bedding 17
8.7 Laying the Pipes 17
8.8 Jointing 17
8.9 Backfilling 18
Appendix 19
A-1 External Loads for Trench Conditions 19


Table of Contents
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
2
01
02
03
04
05
06
07
08
app.
Saudi Arabian Concrete Products
(SACOP) Ltd
SACOP was commissioned in 1978 in Jeddah to
provide high quality precast concrete products for
projects in the Kingdom of Saudi Arabia. The company
is manufacturing reinforced concrete pipes, jacking
pipes, manholes and inspection chambers in Jeddahs
3rd Industrial City and is jointly owned by Ameron Saudi
Arabia Ltd (ASAL) and Ameron International U.S.A.
SACOP is a member of Amiantit Group of Companies, a
Saudi Joint Stock company.
The products manufactured are backed by Amerons
more than 80 years experience in the design, manufacture
and quality assurance of precast concrete products.
The Company produces reinforced concrete pipes,
reinforced concrete pipes with PVC and HDPE T-liners
or GRP liners and reinforced concrete jacking pipes.
SACOP also produces reinforced concrete manholes
with PVC and HDPE T-liners or GRP liners and
inspection chambers.
1 General
Amiantit Group of Companies
The Amiantit Group is a leading global industrial
organization which manufactures high-quality pipe
systems and researches, develops, owns and licenses
advanced pipe technologies; it also provides water
management services. The Group supports global
infrastructure development projects and delivers to
municipal, industrial, agricultural and energy markets
worldwide.
Amiantit has a presence in more than 70 countries,
including almost 30 wholly-owned or joint-ventured
manufacturing facilities in the Middle East, Europe,
Latin America, North Africa, The Far East, Central
Asia, the Indian Subcontinent and Africa. Amiantits
manufacturing capabilities are supported by technology
companies and sales offices across the globe.
Other members of the Group are predominantly limited
liability companies, owned by the Amiantit Group in
varying percentages, which operate under individual
commercial registrations.
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
3
01
02
03
04
05
06
07
08
app.
2 Introduction
Modern sanitation in cities across the world owes much
to concrete. Concrete pipes carry water, industrial
wastes and sewage.
As a material, concrete is rugged and lasts for years
without maintenance. Its load-bearing heavy-duty pipes
can take up to 10 meters of earth cover and the smooth
interior of concrete pipes gives them excellent flow
characteristics.
Rugged, easy to install and problem-free in
performance, reinforced concrete pipes with concrete
bell and spigot joint sealed by a confined rubber
gasket, are manufactured for many applications. Storm
drains, sanitary sewers, culverts, gravity water supply
and irrigation systems are all typical of their versatility.
Security and long-term economy are the main features
of this multi-purpose pipe. With minor modifications to
its steel reinforcement at the design stage, reinforced
concrete pipe can be specified for jacking operations.
Its smooth exterior wall and material strength provide
additional jacking advantage.
Incorporating accurately placed steel reinforcements
in its densely compacted concrete wall or reinforced
concrete wall, reinforced concrete pipes are designed
to withstand substantial live and dead loads. Rugged,
reliable concrete pipes are a safeguard against system
failures. They cant be crushed and wont buckle, split
or deflect, regardless of the service conditions.
The concrete bell and spigot joint, sealed by a confined
rubber gasket for pipe and manhole sections, provides
a flexible watertight joint to eliminate infiltration from
ground water and provides safety for slight movements
due to expansion, contraction, settlement or lateral
displacement.
3 Advantages and
Specications
When looking for a strong, reliable and economical
concrete pipe, consider the characteristics inherent in
SACOPs reinforced concrete pipe.
3.1 Advantages
Concrete pipes and its different modifications show
many advantages in several applications versus other
piping systems. These are in detail:
Strength - concrete and steel are combined for
optimum strength.
Permanence - concrete pipe has conveyed
water and waste for centuries.
Flow characteristics - the smooth, enduring
interior wall provides excellent flow
characteristics.
Uniformity - quality control and in-plant inspections
guarantee uniform quality and performance.
Economy - simple installation, maintenance-
free performance, corrosion resistance and
longevity add to its superior cost-effectiveness.
3.2 Specifications
SACOPs reinforced concrete pipes and pre-cast
reinforced concrete manhole sections are designed and
manufactured in accordance with the specifications
relating to their end use. SACOP manufactures its
products in accordance to:
ASTM C76M
ASTM C443M
BS 5911, Part 1
ASTM C478M
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
4 Production Process
The basic materials of concrete pipes are fine
and coarse aggregate, cement Sulfate Resistant
Cement (SRC) or Ordinary Portland Cement (OPC),
reinforcement, water and admixture. These are
combined in a systematic manner, using quantities and
proportions specially designed for each product. Fine
and coarse aggregates are mixed with cement, water
and admix to provide a concrete mix which is formed
into pipes by a method known as the dry cast process.
The newly formed pipe is steam-cured and then moved
to the coating and finishing area before being shipped
to the construction site.
4.1 Batching And Mixing Of Concrete
Materials
Highly sophisticated batching plant with computerized
batching system will be batched according to the
approved mix design. And also each batching reports
will be produced by the system.
The approved quality of the raw materials supplied,
such as cement,sand and aggregates, conform to the
requirement of ASTM C-150 and C-33. The water used
must be clean, free from chlorine and undesirable
quantities of organic materials, alkali, salt or other
impurities which might reduce the strength, durability or
other desirable qualities of the concrete.
The scales and water meter used in batching are
maintained in good working order and calibrated on a
semi-annual basis.
Picture 4-1 Automatic Batching Picture 4-2 Batching plant
Plant control room
Picture 4-3 Automatic Batching Plant
4.2 Reinforcement (Cage) Fabrication
The welding impulse is electronically released. The
welding intensity and welding time are infinitely
adjustable via an electronic welding control.
The bell-sockets will be manufactured without
interruption of the continuous production. To produce
bell-sockets, the diameter of the reinforcement cage
is increased by expanding the slide dies whereby
expanding speed and longitudinal wire feed speed are
adjusted independently.
The reinforcement cage diameter and the length
between the start and the final wraps (i.e. rings, vertical
to reinforcement cage axis) as well as the taper of the
socket are programmable.
Picture 4-4 Left photo - Pipe steelreinforcement welding cage machine
Picure 4-5 Right photo - Short Pipe and manhole cage welding
4.3 Dry Cast Process
Reinforced concrete pipes are produced in a dry cast
process. This process uses a device rotating at high
speed that forms the interior surface of the pipe. It is
drawn up through the exterior form as the mix is fed
into the form. The head has rollers mounted on the top,
which compact the mix. The profile rings press and
move to build the shape of the spigot. Then both form
and pipe are moved to a curing area where the exterior
form is removed.
A forklift is used to lift the pipe from the machine to
the steam curing kiln. There, the saturated steam will
accelerate the rate of hydration, producing concrete
pipe of the required strength in a shorter time than is
possible when curing at ambient temperature.
Figure 4-6 Dry cast process
5 4
01
02
03
04
05
06
07
08
app.
10
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
4.4 Wet Cast Process
The wet cast proccess is primarily used for producing
manholes and jacking pipes. These are produced
by placing concrete in an assembled pipe mold and
consolidating the concrete by means of pneumatic
vibrators attached to the outer mold. The mold parts,
consisting of a base ring, inner form, outer form and top
header ring are cleaned and form oiled. The automatic
cage machine fabricates the reinforcing cage. GRP,
HDPE and PVC liners are provided in a cylindrical
sleeve that becomes the internal lining of the pipe.
High-frequency vibrators are bolted to the outer form to
consolidate the concrete. The concrete is then batched
by weight, mixed and transported to the mold assembly.
The concrete is poured uniformly into the mold, which
is vibrated to consolidate the material. When the mold
is filled, and the spigot end is formed in the concrete at
the top end of the pipe, the pouring bucket and cone
are removed. The mold assembly, filled with concrete,
is enclosed in a cell and cured overnight at a controlled
temperature. After curing, the pipe is removed from the
mold and transported to yard for final touch-up.
Picture 4-7 Wet Cast Pipe Machine
Piture 4-8 Mould removal after casting.
4.5 Steam Curing
The pipe is placed in a curing chamber and cured in a
moist atmosphere which is maintained by the injection
of steam for a set period of time and at a precise
temperature - this is required to enable the pipe to
meet the strength requirements. The curing chamber is
constructed in such a way as to allow full circulation of
steam around the entire pipe.
Picture 4-9 Curing Chamber
Picture 4-10 Curing chamber
5 4
01
02
03
04
05
06
07
08
app.
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
7 6
01
02
03
04
05
06
07
08
app.
7 6
industrial wastes, SACOPs reinforced concrete lined
sewer pipes should be used (see pages 7 & 8).
When brackish water is to be conveyed, the inside of
the pipe should be coated with bitumen emulsion paint,
coal-tar epoxy, or according to the project specification.
Specications
All sizes of SACOP reinforced concrete storm drain
pipes are designed and manufactured in accordance
with ASTM C76M. Pipe larger than 1200 mm also
conforms with the requirements of BS Specification
5911, Part 1. The bell and spigot joints, sealed with a confined
rubber gasket, meet the requirements of ASTM C443M.
Picture 5 -1 Storm pipe mass
5 Products
5.1 Storm Drain Pipe
SACOPs reinforced concrete pipes, with bell and
spigot joint sealed by a confined rubber gasket, are
extremely suitable for high water table conditions where
infiltration is a continuing and aggravating problem.
Designed specifically for the conveyance of water and
wastewater for low head and gravity flow systems, it has
been used in hundreds of Saudi Arabian and Arabian
Gulf State projects.
Economical to install, its positive and flexible seal
requires neither pointing nor grouting, and bedding and
backfill can follow immediately.
Manufactured in diameters of between 300 and 3500 mm,
the pipes can be designed for substantial external
loads. The bell or spigot ends of the pipe, as well as
the full pipe sections, contain both circumferential and
longitudinal steel reinforcement.
Special pipe and fittings, including short pipe lengths,
laterals, outlets, and wye elbows are available as part
of the pipeline system and shop drawings can be
provided in accordance with site requirements. When the
application entails the conveyance of sanitary sewage or
corrosive
*
Nominal
PipeInside
Diameter
(mm)
Nominal
Pipe Wall
Thickness
(mm)
Nominal
Bell
Outside
Diameter
(mm)
Nominal
Bell
Length
(mm)
Nominal
Joint
Diameter
(mm)
Normal
Joint
Lap
(mm)
Normal
Joint
Space
(mm)
**
Maximum
Joint
Deection
( )
Nominal
Pipe
Laying
Length
(m)
Approx
Mass per
Section
(Kg)
300 69 487 221 378 99 6 3.77 2.5 510
400 77 615 244 488 99 6 2.92 2.5 740
500 86 735 248 600 99 6 2.39 2.5 1020
600 94 880 302 710 99 6 2.01 2.5 1340
700 102 1010 328 849 126 6 1.69 2.5 1700
800 111 1140 380 966 126 6 1.48 2.5 2110
900 119 1260 388 1053 125 6 1.36 2.5 2520
1000 127 1400 432 1194 126 6 1.20 2.5 3020
1100 137 1374 - 1225 94 6 1.17 2.5 3420
1200 144 1488 - 1325 94 6 1.08 2.5 3630
1400 169 1738 - 1578 199 7 0.91 2.5 4974
1500 169 1838 - 1651 199 7 0.87 2.5 5288
1600 178 1956 - 1762 132 8 0.81 2.5 6200
1800 194 2188 - 1980 132 8 0.72 2.5 7200
2000 211 2422 - 2196 132 8 0.83 2.5 8749
2200 228 2656 - 2410 132 8 0.76 2.5 10816
2400 244 2888 - 2616 132 8 0.70 2.5 12604
2500 253 3006 - 2716 137 8 0.67 2.5 13607
Table 5-1 Reinforced concrete storm drain pipe product range
* Diameters from 2600 mm to 3500mm can be designed upon customer request.
** Maximum angular deflection is based on deflecting the joint from its normal assembled position a maximum of
25 mm for 600 mm through 1800 mm diameters, and a maximum of 32 mm for 1900 mm and larger diameters.
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
7 6 7 6
01
02
03
04
05
06
07
08
app.
has a lower friction coefficient than concrete, has a
minimum elongation factor of 200%, and offers no
sustenance to either fungus or bacterial slimes.
Maintaining PVC or HDPE T-lining is no problem. The
dense, glossy surface of the plastic will neither absorb
nor retain precipitated or crystalline materials. It is
easily decontaminated and maintained in a sanitary
condition.
Although the lining rarely sustains damage once the
pipeline is in place, repairs are simple. The damaged
area is cut away leaving the tees embedded and
another piece of lining is welded in place. The newly
fused section is as fully corrosion-resistant as the
original sheet. With the increasing demands placed on
urban wastewater systems, PVC or HDPE offer the most
effective solution to total pollution control at the lowest
cost, based on the service life of the system.
Picture 5 -2 Reinforced Concrete Sewer Pipe with lining
5.2 Reinforced Concrete Sewer Pipe
with Lining
Durability, long life, economy, resistance to acids and
alkalis all are combined in reinforced concrete sewer
pipe lined with any project-specific lining materials like
GRP, HDPE, PVC, and others. When reinforced concrete
sewer lines are installed in aggressive soils, the external
pipe surface can be coated with 100% solids coal-tar
epoxy.
They have the same internal and external lining options
as the reinforced concrete pipes. However, T-lined
pipes use polyvinyl chloride (PVC) and Polyethylene
(PE) polymers welded by a high frequency welding
machine in 2 meter widths. This additional protection
against corrosive liquids and gases gives the pipe a life
time of service.
Specication
SACOPs reinforced concreted sewer pipes are
designed and manufactured in accordance with
ASTM C76M and BS 5911, Part 1. The bell and spigot
joints sealed with confined rubber gaskets meet the
requirements of ASTM C443M.
PVC or HDPE T-Lining
Lining continuity is guaranteed by fusing each individual
pipe liner with the next. This results in a lining that is
permanently flexible, withstands temperatures up to 83
o
C
*Nominal
PipeInside
Diameter
(mm)
Nominal
Pipe Wall
Thickness
(mm)
Nominal
Bell
Outside
Diameter
(mm)
Nominal
Bell
Length
(mm)
Nominal
Joint
Diameter
(mm)
Normal
Joint
Lap
(mm)
Normal
Joint
Space
(mm)
**
Maximum
Joint
Deection
Degree
( )
Nominal
Pipe
Laying
Length
(m)
Approx
Massper
Section
(Kg)
700 102 1010 328 849 126 6 1.69 2.5 1700
800 111 1140 380 966 126 6 1.48 2.5 2110
900 119 1260 388 1053 125 6 1.36 2.5 2520
1000 127 1400 432 1194 126 6 1.20 2.5 3020
1200 144 1488 - 1325 94 6 1.08 2.5 3630
1400 169 1738 - 1578 199 7 0.91 2.5 4974
1500 169 1838 - 1651 199 7 0.87 2.5 5288
1600 178 1956 - 1762 132 8 0.81 2.5 6200
1800 194 2188 - 1980 132 8 0.72 2.5 7200
2000 211 2422 - 2196 132 8 0.83 2.5 8749
2200 228 2656 - 2410 132 8 0.76 2.5 10816
2400 244 2888 - 2616 132 8 0.70 2.5 12604
2500 253 3006 - 2716 137 8 0.67 2.5 13607
Table 5-2 Reinforced concrete sewer pipe wih lining product range
* Diameters from 2600 mm to 3500mm can be designed upon customer request.
** Maximum angular deflection is based on deflecting the joint from its normal assembled position a maximum of
25 mm for 600 mm through 1800 mm diameters, and a maximum of 32 mm for 1900 mm and larger diameters.
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
9 8
01
02
03
04
05
06
07
08
app.
9 8
Jacking (RCJ) pipes under railroads, airport runways,
congested streets and highways is a common practice.
It does not interfere with traffic and it eliminates the
costly maintenance which often results from trench
settlement. Reinforced concrete pipe is particularly
suitable for jacking due to its strength and because it is
not easily deflected from the established line and grade,
as its smooth exterior surface offers little frictional resistance.
During jacking and after installation, the pipelines are
not subjected to unbalanced stresses: when the pipe is
pushed through the soil, it becomes an integral part of
the soil mass as it occupies practically the same space
as the excavated material.
Reinforced concrete pipes with flush exterior are
ideally suited for jacking. A wooden ring is fitted at the
manufacturing plant, made of press board or knotless
softwood, with a thickness of 10-25 mm depending
on the pipe diameter, to ensure the uniform transfer of
pressure between the ends of adjacent pipes.
Picture 5-4 Reinformed concrete jacking pipe.
Glass-ber Reinforced Polyester (GRP) Lining
Manufactured and designed as per the customers
specification. The embedded liner is the interior of the
reinforced concrete pipe, where its thickness ranges
from 4 mm to the required thickness of the project
specification. The liner is a resin rich layer of fiberglass
with a surface veil of chop glass.
Picture 5-3 Concrete pipe with GRP Lining
5.3 Reinforced Concrete Jacking Pipe
(RCJ Pipes)
When surface conditions make it difficult to install pipe
by conventional open excavation and backfill methods,
or when it is necessary to install pipe under an existing
embankment, installation by jacking or tunneling is
used. Reinforced concrete pipe is ideally suited for
tunneling and jacking. The pipe can be pushed forward
immediately after the soil is bore, providing a complete
tunnel liner for the protection of workers and equipment.
Thanks to technological advances and increased
experience, many pipelines are now being jacked.
Reinforced concrete pipes, from 500 mm diameter up
to 3500 mm diameter, have been installed by jacking.
Since conventional jacking procedures require access
by workmen through the pipe to the heading, a 500 mm
diameter pipe is generally the smallest practical size for
most jacking operations.More detailed dimensions of
O.D, pipe length, weight and thickness can be obtained
from SACOP.
500 600 700 800 900 1000 1100 1200
1500 1600 1700 1800 1900 2000 2100 2200
2300 2400 2500 2600 2700 2800 2900 3000
3300 3400 3500
Table 5-3 Reinforced Jacking Pipe Internal Diameter
Drawing 5-1 Reinforced concrete jacking pipe assembled joint section
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
9 8 9 8
01
02
03
04
05
06
07
08
app.
Advantages
Compared to the traditional method, i.e. laying the pipe
in a trench with the resulting surface disruption, the
advantages of the jacking method is described below:
Minimizes disruption to residents and traffic,
requiring only a jacking and reception shaft.
Reduces the risk of damage to adjacent
properties.
Ground tolerant, minimizing de-watering and
ground stabilization.
Accurate installation to 25 mm tolerance of line
and level.
Final installed pipes are stronger than standard
open cut pipes.
Fully remote-controlled, reducing the risk of
accidents.
Requires less road surface reinstatement.
Picture 5-5 RCJ During Jacking
Picture 5-6 RCJ During Jacking
Loads on Jacked Pipe
The two types of load imposed upon concrete pipe
installed using the jacking method are the axial load
resulting from the jacking forces applied during
installation and external earth and live loads.
Axial Loads
The axial or thrust loads are transmitted from one
concrete pipe section to another through the joint
surfaces. To prevent localized stress concentrations,
it is necessary to provide relatively uniform distribution
of the axial loads around the periphery of the pipe.
This is accomplished by ensuring that the pipe ends
are parallel within the tolerances prescribed by ASTM
standards, using a cushion material - plywood -
between the pipe sections, and care on the part of the
contractor to ensure that the jacking force is properly
distributed through the jacking frame and parallel with
the axis of the pipe.
The cross-sectional area of a standard concrete
pipe wall is more than adequate to resist stresses
encountered in normal jacking operations. For projects
where extreme jacking pressures are anticipated due
to long jacking distances or excessive unit frictional
forces, an intermediate jacking station may be used,
and greater care must be taken to avoid stress-bearing
concentrations.
Earth loads
The major factors influencing the vertical earth load on
pipes installed by jacking are:
The weight of the prism of earth directly above the
bore.
The upward shearing or frictional forces between
the prism of earth directly above the bore and the
adjacent earth.
The cohesion of the soil.
Live loads
Jacked installations are generally constructed at
such depths of cover that the effects of live loads are
negligible. Highway and aircraft loads are considered
insignificant at depths greater than three meters;
however, railroad loads are considered significant at up
to nine meters depth of cover.
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
11 10
01
02
03
04
05
06
07
08
app.
11 10
5.4 Reinforced Concrete Manholes
and Inspection Chambers
SACOP precast reinforced concrete manhole and
inspection chambers combine convenience and
economy of installation with the strength and durability
of concrete and steel. Manufactured in a variety
of sizes, these precast assemblies are designed
to fit diverse governmental agency and industry
specification.
Picture 5-7 Reinformed Concrete Manholes
Reinforced Concrete Manholes
Manholes provide one or more of the following functions
in storm water drainage and sanitary sewer lines:
Pipeline access for the purposes of cleaning
and inspecting.
Directional changes in pipeline alignment.
Convergence of two or more pipelines.
Size increase.
SACOP manholes are all circular in section. Since
they are always installed vertically and the external
loads imposed on them due to the surrounding soil is
radially inward. With the section therefore in uniform
compression, the steel reinforcement in the vertical
walls is minimal. In the case of unusual conditions
which result in non-uniform loads around the manholes,
the purchaser must provide SACOP with design
requirement details.

The bottoms of the manholes are reinforced for
protection against normal hydraulic uplift, in cases
where the manhole is installed in wet conditions.
Should a project involve unusual situations or very deep
manholes, the purchaser must provide SACOP with
design requirement details.
Picture 5-8 Reinforced Concrete Mandoles with linings
Flat manhole covers are reinforced to support the
normal and reasonable loads imposed by city traffic.
Their configuration also anticipates at least 20 cm
of cover. Should more severe loads or less cover be
expected, the purchaser must provide SACOP with
design requirement details.
1200 mm is the most common manhole size However,
SACOP also offers 1800 mm, 1600 mm and 1000 mm
manholes. All are available with pre-cast bases and flat
top covers.
Picture 5-9 Disection of a manhole cover slab
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
11 10 11 10
01
02
03
04
05
06
07
08
app.
Reinforced Concrete Inspection Chamber
The basic function of an inspection chamber is to
provide an access point into sewer or storm drain
systems large enough to allow people to enter it and
perform inspection and cleaning procedures manually.
Inspection chambers are designed to provide access
into sewer or storm drain systems for inspection,
cleaning and sampling. Inspection chambers allow all
maintenance work to be carried out from ground level.
SACOP can supply any diameter of inspection
chamber. All are available with pre-cast bases.
The purchaser must provide SACOP with design
requirement details.
Drawing 5-2 Section view of a manhole assembly
Common uses include:
Line clean-out access
Interim access points in long pipe sections
Effluent sampling stations
Monitoring pits
Liners
For sanitary and sewer use, manhole and inspection
chambers can be protected internally with PVC, HDPE,
GRP or coal tar epoxy liners.
Advantages
Convenient for pipe networks.
Cast iron cover locked in a frame to prevent
unauthorized access and noise under passing traffic.
Load conveyance during seasonal air
temperature fluctuations.
Excellent performance in high groundwater
level environments.
Easy cleaning due to smooth interior,
convenient access and use with high pressure
water jetting for removing sedimentation or
blockages within collection systems.
Picture 5-1 GRP lining Picture 5-2 PVC/HDPE lining
Specication
SACOP reinforced concrete manholes are
manufactured in accordance with ASTM Specification
C478M, and can be according to the customers
specification.
13 12
01
02
03
04
05
06
07
08
app.
13 12
6 Pipe Design
Reinforced concrete pipe for gravity flow pipelines in
DN 300 mm through DN 2500 mm sizes may be
specified by D-load strength classification in accordance
with ASTM C76M or by class in accordance with BS 5911
Part I. As an aid to designers, external loads by diameter
are given in Table Appendix for various heights of earth
cover. D-load strength is classified as 0.3 mm crack
strength, D
0.3
, or the ultimate strength, D
ult
. The required
D-load strength in the three-edge bearing test for
reinforced concrete pipe is:
D
0.3
=
[

W
E

+
W
L
]
1

L
E
L
L
ID

___ ___

___
D
ult
=
[

W
E

+
W
L
]
FS

L
E
L
L
ID


___ ___ ___
Where W
E
= earth cover load, (kN/m)
W
L
= live load, (kN/m)
L
E
= load factor for earth load based upon
class of bedding selected
L
L
= load factor for live Load (LE or 1.5,
whichever is less)
ID = pipe inside diameter, (m)
FS = the relationship between D
ult
and D
0.3
The relationship between ultimate D-load and 0.3 mm
crack D-load is specified in the ASTM standard C655M
as For D
0.3
, equal to 100D or less
FS = 1.5
For D
0.3
equal to 150D or more
FS = 1.25
For D
0.3
more than 100D but less than 150D
FS=1.5-
[

D
0.3
- 100

]
(0.25)

_________
50
The D-load strength required for any external cover load
may be determined by
Selecting the method of installation.
Determining the external load. (Table A-1 on Appendix)
Calculating the required D-load strength.
Selecting the class of pipe.


Plain or
reinforced
concrete,
14 MPa min.
300 mm
min.
1.25 Bc
Bc + 200 mm min.
Min. =
Bc ___

4
Min. =
ID ___

4
Densely
compacted
backll
Load factor = 2.8 Plain
Load factor = 3.4 Reinforced
(A5 = 0.4%)
Bc
Concrete cradle

Densely
compacted
backll
Bd
Bc

Bc ___

2
ID to 1600 = 100 mm
Over 1600 = 150 mm
Granular foundation
Load factor = 1.9
Densely
compacted
backll
Compacted
granular
material
300 mm
min.
Class B

Bc
Bd
150 mm
min.
Compacted
granular
material
Granular foundation
Load factor = 1.5
ID to 1600 = 100 mm
Over 1600 = 150 mm
Lightly
compacted
backll

Bc ___

6
Class C

Bc
Bd
Flat suborade
Loose
backll
Class D
Load Factor = 1.1
Figure 6-1 Classes of bedding -trench conduit
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
13 12 13 12
01
02
03
04
05
06
07
08
app.
R =
L
___________
2sin( / 2)
Where R = Centerline radius, (m)
L = Centerline laying length of pipe section, (m)
= Angle turned at pipe joint, ()
(see Table 5-1 or 5-2)
Straight pipe sections may be installed with joint spaces
different from the normal position by deflecting the joint
or by opening or closing the space (F) as illustrated in
figure 6-2 or a combination of deflecting and opening
or closing. These methods are used to lay pipe around
curves, through angle points or for adjustment of line
and grade.
To deflect the joint during installation, insert the spigot
into the bell to the normal joint closure position and
rotate the pipe by maintaining the normal inside joint
space width from Table 5-1 or 5-2 on one side of the
joint space width on the opposite side of the joint.
To open or close a joint to adjust for stationing, insert
the spigot into the bell to the normal joint closure
position and then push the joint closed by reducing
the inside joint space width, or open by increasing the
inside joint space width. Neither the sum of nor the
difference between the measured widths of the total
inside joint spaces, measured at the widest point (F1)
and the closest point (F2) around the circumference,
shall not exceed the values in Table 6-1.
F normal
F opened
F closed
Straight joint Deected joint or
combined adjustment
Installation conditions for concrete joints
F
2
F
1
F
1
F
2
=
Figure 6-2 Installation conditions for concrete joints
Design Example
ID: 1000 mm
Depth of Cover: 3 m
Installation method: Trench
Conduit with Class B bedding
Load factor: 1.9
Earth load: 80.2 kN/m (Please see Appendix)
The load: 4.2 kN/m (Please see Appendix)
D
0.3
=
[

W
E

+
W
L
]
1

L
E
L
L
ID

___ ___

___
=
[

80.2
+
4.2

]
1

1.9

1.5

1.0

____ ___

___
=45.0
D
ult
=
[

W
E

+
W
L
]
FS

L
E
L
L
ID

___ ___ ___
FS= 1.5 for D-load 100 or less.
=
[

80.2
+
4.2

]
1.5

1.9

1.5

1.0

___

___
= 67.5
Referring to the ASTM manual section C76M Table 2.
Class II pipe would be selected (D
0.3
=50)
6.1 Joint Deflection
Reinforced concrete pipe can be laid around long
radius curves and across angle points by deflecting the
joint from the normal closed joint position. The centerline
radius of curvature for any case of deflected joint can
be calculated by the following equation:
Pipe Inside Diameter
(mm)
Maximum Sum of Total Inside
Joint Space
(mm)
Maximum
Deection
(mm)
(ID) (F
1
+F
2
) (F
1
- F
2
)
For reinforced concrete storm drain pipe
300 through 1800 37 25
1900 through 2500 50 32
For lined reinforced concrete sewer pipe
700 through 1800 37 25
1900 trough 2500 50 32
Table 6-1 Inside joint spacing
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
15 14
01
02
03
04
05
06
07
08
app.
15 14
6.2 Types of Joints
SACOP offers a range of joint systems depending on
the pipes it uses, to ensure proper sealing of the gasket
and smooth operation. The following section explains
the various types.
Joints for Concrete Sewer pipes and Storm Drain
pipes
Pipe joint shall be either with flair at the Bell end,
300 mm up to DN 1000 mm or flush for larger diameters.
As illustrated in the drawings
Internal Diameter
Internal Diameter
Joint Space
Joint Space
Nominal Joint Lap
Nominal Joint Lap
Rubber Ring
Rubber Ring
W
a
ll
T
h
ic
k
n
e
s
s
E
x
t
e
r
n
a
l
D
ia
m
e
t
e
r
W
a
ll
T
h
ic
k
n
e
s
s
E
x
t
e
r
n
a
l
D
ia
m
e
t
e
r
Joint for Reinforced Jacking Pipe
Pipe joints for all reinforced concrete jacking pipe are
flush, with a rubber ring gasket to ensure sealing seal
and a steel collar to control the pipes angle. In the
center a wooden ring is set between the pipes as a
pressure absorber to prevent the pipes from cracking
during the jacking process.
DETAIL A
RUBBER
RING
WOOD
STEEL COLLAR
ASTM A-36
33
2
10.19
3551.62
6
Drawing 6-5 Joint for Reinforced jacking pipe
7 Quality Standards
SACOP has its own fully equipped in-house laboratory,
located in the plant. The laboratory operates strictly
in accordance with the factorys quality control
procedures.
Raw materials are tested at source before they are
purchased, to ensure that they comply with the
standards. Concrete mixtures are tested regularly.
All of SACOPs products standard or bespoke have
to meet the Quality Control standards policed by the
companys in-house laboratory. Nothing leaves the
factory without rigorous testing.
Drawing 6-4 Diameter 1100 mm - 2500 mm
Drawing 6-3 Diameter 300 mm - 1000 mm
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
15 14 15 14
01
02
03
04
05
06
07
08
app.
8.3 Rubber Gaskets
Rubber gaskets should be kept clean and away from
contaminants like petroleum products, and should be
stored undercover if the pipes are not to be installed in
the trench within a few days.
Caution: Do not attempt to use Rubber Gaskets
other than those shipped with the pipes. They are
matched to the product. Any other type of gaskets
may be too large and make jointing difficult, or if too
small will not effects a proper seal.
Angular Rubber Gasket Installation Procedure
The pipe should be handled with extreme
caution to avoid chipping of the spigots or
bell grooves.
The clean spigot end, including the step seating,
are for the gaskets. Place the gasket in the step
of the spigot, making sure that the pointed end of
the gasket is toward the end of the pipe.
lubricant
Figure 8-1 Joint lubricant area
Remove all dirt and other foreign matter from the
inside surface of the bell. Apply lubricant to the
inner surface of the bell including the lead-in taper
surface on the outer edge of the bell. Align the
spigot with the bell. The gasket should touch lead-
in taper around the entire circumference before the
pipe is pushed home

Proper bedding is necessary to ensure continuous
support of the entire pipe and joint.
Push the pipe carefully, until the spigot is all
the way home.
Internal Diameter
Internal Diameter
Joint Space
Joint Space
Nominal Joint Lap
Nominal Joint Lap
Rubber Ring
Rubber Ring
W
a
ll
T
h
ic
k
n
e
s
s
E
x
t
e
r
n
a
l
D
ia
m
e
t
e
r
W
a
ll
T
h
ic
k
n
e
s
s
E
x
t
e
r
n
a
l
D
ia
m
e
t
e
r
Drawing 8-2 Diameter 1100 mm - 2500 mm
Drawing 8-1 Diameter 300 mm - 1000 mm
1
2
3
4
5
8 Underground Installations
for Buried Pipe
8.1 Introduction
This is the abridged version of the Reinforced Concrete
Pipe Installation Guide, which is a full installation guide
to ensure that pipes are installed to comply with a
controlled installation procedure, in order to ensure
that they meet all requirements. It does not replace
the specification or any contractual requirements
and should be regarded as complementing these
documents.
This abridged version is directed primarily at sub-division
type works and reflects a growing trend among local
authorities to nominate rubber gaskets for the joining of
pipes of 300 to 3500 mm.
With a focus on safety, it is intended that this guide will
illustrate to all involved that the right way is invariably
the quickest and least expensive way to install
reinforced concrete pipes (RCP).
8.2 Unloading and Handling
Reinforced concrete pipes can be handled with most
conventional lifting equipment but should not be
handled carelessly. Damaged pipe ends may have
to be repaired so that effective joints can be made
and such repairs can be time- consuming and costly.
Appropriate lifting chains and equipment, are necessary
for safe handling.
Unloading locations should be chosen with care to
ensure there will be a minimal amount of rehandling
and intra site transport prior to getting the pipe into the
trench.
Caution: Profits can be made or lost in this area.
Pay particular care to potential
interference from overhead wiring.
This is a source of great danger!
Pipe sections should be adequately
chocked while stockpiled at the job
site. A slight slope, soft ground or
vibration from trenching operations
could start the pipes rolling and
the results could be disastrous.
The cost of chocking is a very
small price to pay for insurance
against possible construction delays, not to mention the
potential for injury or loss of life.
It is good practice to inspect each pipe as it comes
off the truck. Pipes damaged in transit or not up to
specification should be put on-hold for inspection and
repair. This inspection plan will then ensure that only
first class product will be installed. The driver should be
instructed to inspect the pipes as they are loaded and
to carry them so as to avoid damage in transit.
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
17 16
01
02
03
04
05
06
07
08
app.
17 16
8.4 Trench
Site Investigations
Before work commences, contractors, manufacturer
and authorities should endeavor to obtain as much
information as possible about the ground conditions
of the work site. Sources of information, which may be
available, are:
Natural surface features, such as rocky outcrops,
watercourses or swamps should be inspected and
the drainage system for the surface run off located in
relation to the line of the proposed excavation.
Information on ground conditions may be available
from nearby works such as existing railway cuttings
or roadways, electric and telephone lines.
Excavating the Trench
The information outlined in this section refers to
excavations with vertical faces or near-vertical sides
and does not apply to those excavations where the
sides of the excavation have been battered back so
as to slope at such an angle that there is no danger of
them collapsing. The subject of trench-shoring methods
is fully covered in the unabridged version.
Trench walls which are firm and solid when first dug may
not remain so. In hot dry weather, enough of the soils
moisture may be evaporated from the exposed faces
to cause eventual collapse. In wet weather, water may
saturate an initially stable trench wall and cause it to fail.
Also vibrations from nearby construction equipment may
be enough to trigger a collapse. The time to prevent a
trench wall movement is before it starts.
Excavated Material
Excavated material should be placed far enough away
from the top of the trench to allow sufficient clearance
for installation operations and to minimize the danger of
rocks and or lumps rolling back into the trench. Where
there is restricted room it may prove economical to load
out all or part of the excavated material and stockpile
it for use as backfilling elsewhere. A large proportion
of the cost of a trenched pipeline installation is in the
excavation and backfill. And therefore large savings
can be made by taking care when planning these
operations and by evaluating the alternatives available,
including shoring.
8.5 Foundations
The foundation for a pipeline is the material under the
pipes. Its stability and uniformity along the line rates as
one of the most important aspects to ensure crack free
installations. Pipes are designed to be uniformly loaded
along their length and to be uniformly supported along
their length to carry the load.
Unless the disturbed foundation material is replaced
with carefully compacted material the pipes laid above
will be left with inadequate support and pipes may
crack circumferentially as a result. Where the pipes
are connected to pits and manholes it is good design
and installation practice to use two short lengths,
thereby increasing the flexibility of the line in this area of
potential ground movement.
Problems are also associated with hard foundation
material. Where it consists of rock or other very firm
material it becomes difficult or impossible to excavate
a trench with a bottom even enough to provide uniform
support for the pipes. It is therefore necessary to
over excavate and replace a sufficient depth with
suitable material to ensure a uniform and slightly
yielding support all along the pipeline. The depth of
the over excavation must be sufficient for the effect
of unevenness of the hard material below not to be
transmitted through the pipes, as this is a source
of point loading. Most importantly holes (recesses)
must be excavated to allow a cushion to be provided
underneath the sockets and so remove the most
common cause of point loading.
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
17 16 17 16
01
02
03
04
05
06
07
08
app.
8.6 Bedding
The bedding is the cushion material between the pipes
and the foundation. Its function is to ensure uniform
support for the pipeline both with regard to grade and
hardness. A bedding specification must form part of
any pipe laying specification as it influences the pipe
strength required.
Depending on the foundation the bedding material may
consist of the foundation material or of an imported
material.
The best bedding material is granular and uniformly
graded which assists in handling and spreading. It only
needs sufficient compaction to ensure that laying
tolerances are maintained when pipes are laid and
backfilled. Holes (recesses) in the bedding must be
provided for the protruding socket to ensure uniform
support of the barrel and hard point supports must be
avoided.
8.7 Laying the pipes
Before handling the pipes, check their mass, weight
and dimensions and make sure the handling equipment
is of adequate strength. Pipes laying usually progresses
in an upstream direction with the spigot pointing
downstream having been inserted into the socket.
Doing it this way restrains the joints from opening up
as a result of pipeline movement and joint surfaces are
protected against entry of foreign matter. If adequate
precautions are taken with regard to these items, there
is no reason why the order may not be reversed.
Many pipes are manufactured with elliptical steel
reinforcement and as such must be laid in a specific
direction. These pipes are supplied with a top mark, to
make sure that they are laid top up.

To ensure that pipes are laid to the correct grade within
the specified tolerances some installers will optionally
lay the pipes on timber, brick or stone supports.
Such supports, if placed on a hard foundation can
result in damage to the pipes due to the point load
(concentrated reaction) they impose on the pipe when
backfilled. Such supports must be removed before
backfilling. The desire to achieve tight laying inle and
grade tolerances must not result in the uniform support
of the pipe being compromised.
Rubber gasket jointed pipes must be laid with joint
gaps between the pipes to ensure that the lines are
able to deflect without causing damage to the pipes.
Recommended joint gaps are shown on all product
drawings and are tabulated. Witness marks are
provided on the outside of pipes to show maximum and
minimum gaps.
8.8 Jointing
The rubber gasket must be assembled dry (put on
spigot) and without the use of lubricant.
Before jointing, clean and inspect all joint surfaces.
Dirt, dust and foreign matter must be removed from the
spigot and bell and pipes with damaged joints must be
repaired. Rubber gaskets must be clean and dry and
damaged rubber gaskets must not be used.
Place the rubber gaskets on the spigot and ensure
that the gasket is free of unevenness or twists. The
spigot should then be offered to the socket with uniform
contact of 360 to the socket lead in. The pipe is then
pushed home.
x
Figure 8-4 Correct joining method Figure 8-5 Incorrect joining method
Figure 8-2 Correct bedding
Figure 8-3 Incorrect bedding
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
19 18
01
02
03
04
05
06
07
08
app.
19 18
8.9 Backfilling
The most important point about backfilling is to realize
that compaction loads/ construction vehicle loads will in
most cases be the most severe load to which the pipe
is subjected. Make sure the manufacturer has allowed
for this.
1 Avoid damaging the pipes by direct impact.
Keep heavy rocks and other such material out
of the fill adjacent to the pipe and the
embedment zone.
2 Bring up the fill on both sides together to
ensure that pipeline alignment is maintained.
Use a hand held compactor to do this, to
ensure that there is no overload.
3 Avoid running heavy construction equipment
over the pipes in an uncontrolled manner.
4 Ensure that the pipe is compacted with a
pedestrian roller to the requisite level
over the top of the pipe prior to bringing on
compaction and construction loads.
5 If the backfill procedure is to be varied from
the design seek approval from the
manufacturer.
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
19 18 19 18
01
02
03
04
05
06
07
08
app.
Appendix
A-1 External Loads for Trench Conditions
Load values given in the table below are for the field
conditions described in these criteria conditions other
than those indicated appropriate adjustments must be
made or new calculations will be required.
Load in kN/m
Pipe Diameter in mm
Cover
Meters
External
Load
300 400 500 600 700 800 900 1000 1100 1200 1300
0.5
Earth Load 5.0 6.1 7.2 8.0 9.1 10.1 11.2 12.3 13.4 14.4 15.5
Live Load 23.2 30.4 37.1 41.5 48.0 54.5 60.9 67.4 73.8 76.6 79.6
Total 8.2 36.5 44.3 49.5 57.1 64.6 72.1 79.7 87.2 91.0 92.1
1.0
Earth Load 11.5 14.8 16.9 18.2 20.3 22.4 24.5 26.7 28.8 30.9 33.1
Live Load 7.4 9.7 11.8 13.2 15.3 17.3 19.3 21.4 23.5 25.5 27.6
Total 18.9 24.5 28.7 31.4 35.6 39.7 43.3 48.1 52.3 56.4 60.7
1.5
Earth Load 17.4 21.1 24.4 26.6 29.8 33.0 40.4 43.5 46.6 49.8 53.0
Live Load 4.2 5.5 6.8 7.6 8.8 9.9 11.1 12.3 13.4 14.6 15.8
Total 21.6 26.6 31.2 34.2 38.6 42.9 51.5 55.8 60.0 64.4 68.8
2.0
Earth Load 21.7 26.2 30.5 33.4 37.6 41.9 53.4 57.7 62.0 66.2 70.6
Live Load 2.8 3.6 4.4 4.9 5.7 6.5 7.2 8.0 8.8 9.5 10.3
Total 24.5 29.8 34.9 38.3 43.3 48.4 60.6 65.7 70.8 75.7 80.9
2.5
Earth Load 25.0 30.6 35.8 39.4 44.6 49.8 64.0 69.4 74.7 80.0 85.4
Live Load 1.9 2.5 3.1 3.5 4.0 4.6 5.1 5.6 6.2 6.7 7.3
Total 26.9 33.1 38.9 42.9 48.6 54.4 69.1 75.0 80.9 86.7 92.7
3.0
Earth Load 27.8 34.3 40.4 44.6 50.8 56.9 73.8 80.2 86.4 92.8 99.2
Live Load 1.4 1.9 2.3 2.6 3.0 3.4 3.8 4.2 4.6 5.0 5.4
Total 29.2 36.2 42.7 47.2 53.8 60.3 77.6 84.4 91.0 97.8 104.6
3.5 Load 31.3 39.0 46.2 51.2 58.6 65.9 86.9 93.3 100.9 108.9 116.3
4.0 Load 33.0 41.4 49.4 54.8 62.9 71.1 93.2 101.8 110.2 118.7 127.4
4.5 Load 34.4 43.5 52.1 58.1 66.9 75.8 100.3 109.7 119.0 128.4 138.0
5.0 Load 35.7 45.3 54.6 60.9 70.5 80.1 106.8 117.1 127.3 137.5 148.0
5.5 Load 36.7 49.9 56.7 63.5 33.7 84.1 112.8 123.9 135.0 146.1 157.5
6.0 Load 37.6 48.2 58.6 65.8 76.6 87.6 118.4 130.3 142.1 154.1 166.3
6.5 Load 38.3 49.4 60.2 67.8 79.2 90.8 123.5 136.2 148.8 161.5 174.6
7.0 Load 38.9 50.3 61.7 69.5 81.5 93.7 128.2 141.6 154.9 168.5 182.4
7.5 Load 39.4 51.2 62.9 71.1 83.5 96.2 132.5 146.6 160.7 174.9 189.6
8.0 Load 39.8 51.9 64.0 72.4 85.4 98.6 136.4 151.2 166.0 181.0 196.4
8.5 Load 40.1 52.5 64.9 76.6 87.0 100.7 140.1 155.5 170.9 186.6 202.8
9.0 Load 40.4 53.1 65.7 74.7 88.4 102.6 143.4 159.4 175.5 191.8 208.7
9.5 Load 40.7 53.5 66.5 75.6 89.7 104.2 146.4 163.0 179.7 196.7 214.2
10.5 Load 40.9 53.9 67.1 76.4 90.8 105.8 149.2 166.4 183.6 201.3 219.4
Table A-1 External Loads for Trench conditions
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
21 20
01
02
03
04
05
06
07
08
app.
21 20
Load in kN/m
Pipe Diameter in mm
Cover
Meters
External
Load
1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 2500
0.5
Earth Load 16.6 17.7 19.5 20.4 21.4 22.4 23.5 24.6 25.7 26.7 27.8 28.9
Live Load 76.6 76.6 76.6 76.6 76.6 76.6 76.6 76.6 76.6 76.6 76.6 76.6
Total 93.2 94.3 96.1 97.0 98.0 99.0 100.1 101.2 102.3 103.3 104.4 105.5
1.0
Earth Load 35.2 37.4 41.0 42.8 44.7 46.8 48.9 51.1 53.2 55.4 57.6 59.7
Live Load 29.6 31.7 35.1 36.8 38.6 40.6 42.6 44.7 46.7 48.8 50.8 52.9
Total 64.8 69.1 76.1 79.6 83.3 87.4 91.5 95.8 99.9 104.2 108.2 112.6
1.5
Earth Load 56.1 59.3 64.6 67.4 70.1 73.2 76.4 79.7 82.9 86.1 89.3 92.6
Live Load 17.0 18.1 20.1 21.1 22.1 23.2 24.4 25.6 26.8 27.9 29.1 30.3
Total 73.1 77.4 84.7 88.5 92.2 96.4 100.8 105.3 109.7 114.0 118.4 122.9
2.0
Earth Load 11.1 11.8 13.1 13.8 14.4 15.2 15.9 16.7 17.5 18.2 19.0 19.8
Live Load 86.0 90.9 99.4 103.8 108.1 113.0 118.0 123.1 128.3 133.3 138.4 143.6
Total 90.7 96.0 104.9 109.5 114.2 119.3 124.7 130.1 135.5 140.8 146.2 151.7
2.5
Earth Load 7.8 8.3 9.2 9.7 10.2 10.7 11.2 11.8 12.3 12.8 13.4 13.9
Live Load 98.5 104.3 114.1 119.2 124.4 130.0 135.9 141.9 147.8 153.6 159.6 165.6
Total 105.5 111.9 122.5 128.0 133.5 139.7 146.1 152.6 159.0 165.4 171.9 178.4
3.0
Earth Load 5.8 6.2 6.9 7.2 7.6 8.0 8.4 8.8 9.2 9.6 10.0 10.4
Live Load 111.3 118.1 129.4 135.2 141.1 147.7 154.5 161.4 168.2 175.0 181.9 188.0
Total 123.9 131.6 144.4 151.1 157.7 165. 173.0 180.8 188.6 196.4 204.1 212.1
3.5 Load 136.0 144.6 159.0 166.5 174.0 182.3 191.0 199.9 208.6 217.4 226.1 235.0
4.0 Load 147.5 157.0 173.0 181.3 189.6 198.9 208.6 218.4 228.1 237.8 247.5 257.4
4.5 Load 158.4 168.9 186.4 195.5 204.6 214.8 225.4 236.3 24.9 257.6 268.3 279.3
5.0 Load 168.7 180.1 119.1 209.0 218.9 230.0 241.6 253.4 265.0 276.7 288.3 300.2
5.5 Load 178.4 190.6 211.2 221.9 232.6 244.6 257.1 269.8 282.4 295.0 307.6 320.5
6.0 Load 187.6 200.6 222.7 234.1 245.6 258.5 271.9 285.6 299.1 312.6 326.2 340.1
6.5 Load 196.1 210.1 233.5 245.7 257.9 271.7 286.0 300.7 315.7 329.6 344.1 358.9
7.0 Load 204.2 218.9 243.8 256.7 269.7 284.3 299.5 315.1 330.4 345.8 361.2 377.7
7.5 Load 211.8 227.3 253.5 267.1 280.8 296.3 312.4 328.8 345.0 361.3 377.7 394.4
8.0 Load 218.9 235.1 262.7 227.0 291.4 307.7 324.6 341.9 359.1 376.2 393.5 411.1
8.5 Load 225.5 242.5 271.3 286.4 301.5 318.5 336.3 354.5 372.5 390.5 408.6 427.2
9.0 Load 231.7 249.5 279.5 295.5 311.0 328.9 328.9 347.4 366.5 404.2 423.2 442.6
9.5 Load 237.8 256.0 287.3 303.6 320.1 338.7 358.0 377.9 397.5 417.3 437.1 457.4
10.5 Load - - - - - - - - - - - -
Table A-1 External Loads for Trench conditions
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
21 20 21 20
01
02
03
04
05
06
07
08
app.
Backll
Earth loads in Table A-1 are based on Marstons trench
load curve for saturated topsoil. When K

=0.150
the table is conservative for sands, gravels and
cohesionless materials. The earth load should be
recomputed for clay backfills when K

is less than 0.150

using the correct coefficient.
Table A-1 has been computed for materials with a
mass/unit volume of 1900 kg/m
3
. For materials with a
mass per unit volume other than 1900 kg/m
3
the correct
earth load can be calculated by multiplying the earth
load shown in Table A-1 by the desired unit mass and
dividing by 1900.
Trench width
The earth loads on Table A-1 are given for all pipe
diameters for covers of 0.5 and 1.0 and 1.5 meters are
independent of trench width.
This condition is true because the trench width
generally exceeds the calculated transition width for
these covers. ie the calculated earth load for the trench
condition exceeds the maximum load as calculated for
the positive projecting condition.
The design assumptions are for r
sd
p equal 0.5 and the
backfill K

is 0.192 for all the soil types.

Loads given in Table A-1 for cover of 2.0 meters and
greater are based on trench widths (at top of pipe) of
pipe OD plus 400mm for pipe diameters 800mm or less,
and pipe OD plus 600mm for pipe diameters greater
than 800mm.
Pipe ODs are based on wall thicknesses given in the
dimensional data table for pipe.
Live loads
Live load distribution in Table A-1 is calculated from the
dimensions for a single AASHTO H-20 or H-20 truck.
The force exerted by each dual-tired wheel is 72 kN.
For different wheel forces correct live loads can be
obtained by multiplying live loads shown by the desired
wheel load in kN and dividing by 72. The live load at
0.5 meters is increased by 20% for impact. For covers
3.5 meters and greater, the small effect of live loads is
included in the tabulated load (see Table A-1).
P
D
F

V
e
r
s
i
o
n

C
o
p
y
r
i
g
h
t

A
m
i
a
n
t
i
t
Utmost care has been
taken to ensure that all the
contents of this brochure
are accurate. However,
Amiantit and its subsidiaries
do not accept responsibility
for any problems which
may arise as a result of
errors in this publication.
Therefore customers should
make inquries into the
potential product supplier
and convince themselves
of the suitability of a given
products supplied or
manufactured by Amiantit
and/or its subsidiaries
before using them.
Saudi Arabia Concrete
Products (SACOP) Ltd.
Jeddah
P.O. Box 7727
Jeddah 21472
Phone: + 966 2 637 31 42
+ 966 2 637 44 06
Fax: + 966 2 637 45 51
[email protected]
www.amiantit.com
Distributed by: