Scribd
Upload
4K views6 pages

Section A: Instructions: A Total of 25 Questions With 30 Minutes Duration For This Section. Each

This document provides instructions for a 25 question, 30 minute exam section with questions on geometric dimensioning and tolerancing (GD&T). It includes sample multiple choice questions on GD&T topics like material condition, flatness, circularity, symmetry, profile of surface, and others. The questions cover concepts like datum reference frames, tolerance zones, and the differences between various GD&T controls.

Uploaded by

Amit_Dhimanj
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
4K views6 pages

Section A: Instructions: A Total of 25 Questions With 30 Minutes Duration For This Section. Each

This document provides instructions for a 25 question, 30 minute exam section with questions on geometric dimensioning and tolerancing (GD&T). It includes sample multiple choice questions on GD&T topics like material condition, flatness, circularity, symmetry, profile of surface, and others. The questions cover concepts like datum reference frames, tolerance zones, and the differences between various GD&T controls.

Uploaded by

Amit_Dhimanj
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 6

SECTION A

Instructions: A total of 25 questions with 30 minutes duration for this section. Each
question carries 1 mark.
1.) What is the MMC for a relevant FOS belo!
a) 10.6 b) 26.1 c) 10.2 d) 26.0

".) Flatness is the con#ition of surface



$.) When no flatness control is s%ecifie#& the flatness of surface is controlle#
b'




(our choice:
the process engineer
the nominal of the size dimension
Rule#1 and the size dimension.
Rule # 2 and the size dimension.
the title block tolerance.
eing !ithin t!o parallel planes.
ha"ing all of its elements in one
plane
is at its nominal size dimension
#ontain no nicks or scratchs
being !ithin it size
tolerance.

).) The virtual con#ition for the %in #ia*eter is



+.) ,o *an' -au-es.si*ulators are nee#e# for ins%ection for the %art belo!
a.)$ b.) 6 c.) % d.) &
/.) What #oes the acron'* ASME ( 1).+ M stan#s for!

(our choice:
undefined
11.2
1'.&
1'.2
12.&
&.) When no -eo*etric control is shon& hat controls the strai-htness of surface the
ele*ents!




0.) What controls the circularit' of #ia*eter 1!



(.) )o! man* modifiers are used in +, - ./

a.) $ b.) 0 c.) + #.) /
2.) #hoose for !hich of the belo! control 0aterial conditions are not applicable
i) 1*mmetr* ii) runout iii) profile of surface 23) straightness

a.) i 3 iii b.) ii an# iv c) all #) i& ii& iii
Rule #1
Rule#2
4 note in the
titleblock
5othing it is undefined
.he circularit* control
sho!n
.he nominal e6traction of the surface
te6ture
.he surface te6ture of the surface
Rule#2 and the size dimension
.he limits of the size dimension
Rule#1and the size dimension
14.) 7hich of the follo!ing is true about the +eometric #ontrol8 9rofile of surface/

a.) 2t is dependent on a ,atum reference
b.) 2t is not dependent on a ,atum reference
c.) 2t ma* or ma* not use a referenced ,atum
d.) 5one
11.) #hose the right option from belo!
a) :latness is gi"en !ith reference to a datum.
b) 0aterial condition is applicable to angularit* control
c) 1*mmetric control comes under categor* of orientation.
d) 0aterial condition can be applicable for c*lindricit* control.
12) #hoose the right statement on tolerance zone.
a) 9rofile of surface indicates the tolerance zone of t!o planes apart along a true
profile.
b) #oncentricit* talks about t!o concentric circles apart.
c) 1*mmetr* talks about median points of e6treme opposite elements
d) :latness talks about t!o parallel lines apart.
1') 7hich of the follo!ing datum is responsible for orientation/


(our choice:
1$) ;ist the t*pe of orientation control.
55555555555555555555555555555555555555555555555555555555555555555555555555
1<) 4n ad"antage of profile tolerancing is



16) .he tolerance zone for a flatness control is


1&) 7hat is the shape of the tolerance zone for the c*lindericit* control/



1() 7hich rule defines the minimum number of points of contact bet!een the part and its
datum planes/
================================================
4 sprial path along the surface of the
diameter
4 c*linder about the datum
a6is
.!o coa6ial c*linders
.!o coa6ial circles
4 c*linder
the limits of the size dimension
t!o parallel lines
t!o parallel planes
t!o planes
t!o lines.
5o flat or re"ersals are allo!ed.
.olerance can accumulate
Rule#1
4 clear definition of tolerance zone.
>6tra tolerance
1%) 4 function gage is a gage that



"4."+ Ansers belo 6uestions5 true or false.
21) .otal run out is a 2=dimensional control.
22) 9rofile of a line tolerances appl* to an entire surface.
2') 9ositional tolerances are applied to indi"idual or patterns
of features of size.
2$) 9ositional tolerances are applied on an 00#8 ;0#8 or
R:1 basis.
2<). 4 material modifier s*mbol is not re?uired for R:1.
2s used !hen a tolrance is applied at R:1
2s used to collect manufacturing data.
2s built to the 00# of the toleranced
feature.
3erifies functional re?uirment of part
features.
#ost more than a "ariable gage.

You might also like