Scribd
Upload
1K views

Lic Lab Model Questions

The document contains instructions for 30 experiments to be performed in an integrated circuits lab. The experiments include obtaining transfer characteristics for non-inverting and inverting amplifiers, generating waveforms using IC 555 timers to produce pulses and signals of various frequencies, designing filters with different roll-off rates, realizing expressions using operational amplifiers, and designing logic circuits to control LEDs on various timing schedules using multiple multivibrators. Hints are provided for each experiment utilizing common integrated circuits.

Uploaded by

basheervp
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
1K views

Lic Lab Model Questions

The document contains instructions for 30 experiments to be performed in an integrated circuits lab. The experiments include obtaining transfer characteristics for non-inverting and inverting amplifiers, generating waveforms using IC 555 timers to produce pulses and signals of various frequencies, designing filters with different roll-off rates, realizing expressions using operational amplifiers, and designing logic circuits to control LEDs on various timing schedules using multiple multivibrators. Hints are provided for each experiment utilizing common integrated circuits.

Uploaded by

basheervp
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

basheervaliyapeedikakkal@gmail.

com 1

EC 04 507 (P) LINEAR INTEGRATED CIRCUIT LAB.

1. Obtain the following transfer characteristics.

Hint: Non-inverting amplifier with gain 20.


2. Obtain the following transfer characteristics.

Hint: Inverting amplifier with gain 20.


3. Generate the waveform,

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.


[email protected] 2

4. Generate a pulse waveform of frequency 1 KHz and 50% duty cycle.


Hint: AMV using IC 555 timer with 1 KHz and Tc = Td = O.5mS = 0.69RC, where
R=RA=RB. (Diode must be connected across the resister RB).

5. Design and setup a filter with roll off rate = 60 dB/decade.


Hint: Use a second order HPF cascaded with another first order HPF.

6. Design and setup a filter with roll off rate = -40 dB/decade.
Hint: Second order LPF.

7. Design and setup a filter with roll off rate = 40 dB/decade, which blocks all the
signals of frequency less than 2 KHz and greater than 6 KHz.
Hint: Second order LPF with higher cut off frequency 6 KHz cascaded with second order
HPF with lower cut off frequency 2 KHz.

8. Realize the expression,


y=5x + dx/dt + 4 ; x=sin (2000πt).

Hint:

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.


[email protected] 3

9. Realize the expression,


y= - (5x + ⌡x dx + 4) ; x=2sin (2000πt).
Hint:

10.Generate the waveform,

Hint:

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.


[email protected] 4
11.Generate the waveform,

Hint:

12.Generate the waveform,

Hint:

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.


[email protected] 5
13.Generate the waveform,

Hint:

14.Generate the waveform,

Hint:

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.


[email protected] 6
15. Generate the waveform,

Hint:

16. Generate the waveform,

Hint: AMV using Op-amp with frequency 1 KHz and duty cycle 1/3.

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.


[email protected] 7
17. Generate the waveform,

Hint:

18. Obtain the following transfer

characteristics.

Hint: Schmitt trigger with bias supply. (Refer Lab Manual Volume 2 – page no:102)

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.


[email protected] 8
19. Generate the waveform,

Hint:

20. Generate the waveform,

Hint:

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.


[email protected] 9
21. Generate the waveform,

Hint:

22. Generate the waveform,

Hint:

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.


[email protected] 10
23. Generate the waveform,

Hint:

24. Generate the waveform,

Hint: Design two AMVs one for 2 KHz and other for 0.166 KHz (1/6mS) frequency using IC
555 timer. The 0.166 KHz square waveform output must be fed to the RESET pin (pin no: 4)
of second multivibrator.

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.


[email protected] 11
25. Generate the waveform,

Hint:

26. Generate the waveform,

Hint:

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.


[email protected] 12
27. Generate the waveform,

Hint:

28. A bulb at the railway station will be switched ON at 9am by the Station Master. It
should be switched OFF at 9.12am automatically. Design and setup a circuit to operate
the bulb.
Hint: Use MMV with 12 minutes quasi period. Station Master can be switched ON the bulb
by triggering the MMV.

29. Design and setup a logic circuit to glow an LED four times at every minutes.
Hint: Design two AMVs, one for 4S T-on and 56S T-off and other for 1S square wave using
IC 555 timer. The first multivibrator output must be fed to the RESET pin (pin no: 4) of
second multivibrator.

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.


[email protected] 13
30. Design and setup a logic circuit to glow an LED three times at every alternate
minutes.
Hint: Design two AMVs one with 3S T-on and 117S T-off and other for 1S square wave
using IC 555 timer. The first multivibrator output must be fed to the RESET pin (pin no: 4)
of second multivibrator.

……………………………………………………………………………………….................
NB: For solving questions starting with “OBTAIN” (eg: - Qn.No: 1), signal generators can
be used. But in case of questions starting with “GENERATE” (eg:- Qn.No: 3) , no signal
generators can be used.

……………………………………………………………………………………….................

********************** WISH YOU ALL THE BEST **************************

Basheer.V. P S8 EC-1 MEA Engineering college,Perinthalmanna.

You might also like