SN359-1 Material Comparison German-Chinese 2012-06 E-1

June 2012
Table of contents Page

1 Scope ............................................................................................................................................................................ 1
2 Normative references .................................................................................................................................................... 1
3 Comparison of material designations ............................................................................................................................ 1
4 Comparison of material characteristics .......................................................................................................................... 1
Annex A1 (normative), Comparison of German and Chinese material designations, steels .............................................. 2
Annex A2 (normative), Comparison of German and Chinese material designations, cast steels ....................................... 9
Annex A3 (normative), Comparison of German and Chinese material designations, cast irons ...................................... 11
Annex A4 (normative), Comparison of German and Chinese material designations, non-ferrous metals ........................ 12
Annex B1 (normative), Comparison of German and Chinese material properties, steels ................................................ 14
Annex B2 (normative), Comparison of German and Chinese material properties, cast steels ......................................... 34
Annex B3 (normative), Comparison of German and Chinese material properties, cast irons........................................... 38
Annex B4 (normative), Comparison of German and Chinese material properties, non-ferrous metals ............................ 40

1 Scope
The comparison of German and/or European and Chinese materials is based on the selection of materials in the Book of
Standards, Part 1. It is intended to help in selecting comparable Chinese materials and their use instead of the materials
specified on the drawings.
Missing material comparisons will be added in the new edition of the standard and until then can be determined by enquiring
at the Standards Office.

2 Normative references
SMS Siemag Book of Standards 2008, Part 1.

3 Comparison of material designations
The European/German materials in annexes A1 to A4 (normative) are compared with Chinese materials. The selection of the
comparison material is made on the basis of the degrees of matching of chemical composition and mechanical properties.
The comparison uses three degrees of matching:

identical = The two materials are identical with regard to their essential properties.
similar = The two materials are identical with regard to their essential properties; existing deviations must be checked
to determine the usability of the material.
do not use = The comparison material does not fulfill the properties of the material specified on the drawing and shall not
be used.

4 Comparison of material properties
The European/German materials and their properties listed in Annexes B1 to B4 (normative) are compared with Chinese
materials and their properties. The selection of the comparison material corresponds to that in Annexes A1 to A4 and is based
on the degrees of matching of chemical composition and mechanical properties.

Matching or deviation can be detected and evaluated immediately by means of the values listed.

Revision of June 2012
Updating of pipe and forging materials
Materials for flat products DIN EN 10028-2 newly added.
Updating of various material properties.
Editorial revision.
Use of SMS group logo.
Total number of pages: 44
Edited by:
SMS Siemag
Standards Office
SMS Siemag for SMS GmbH 2012
The reproduction, distribution and utilization of this document as well as the communication of its contents to
others without express authorization are prohibited. Any violations will result in an obligation to pay damages.
All rights reserved.

Materials
Comparison of German and Chinese materials
Selection
SN 359-1
ICS 77.080, 77.120
N
o

g
u
a
r
a
n
t
e
e

c
a
n

b
e

g
i
v
e
n

i
n

r
e
s
p
e
c
t

o
f

t
h
i
s

t
r
a
n
s
l
a
t
i
o
n

I
n

a
l
l

c
a
s
e
s

t
h
e

l
a
t
e
s
t

G
e
r
m
a
n
-
l
a
n
g
u
a
g
e

v
e
r
s
i
o
n

o
f

t
h
i
s

s
t
a
n
d
a
r
d

s
h
a
l
l

b
e

t
a
k
e
n

a
s

a
u
t
h
o
r
i
t
a
t
i
v
e

T
h
i
s

c
o
p
y

w
i
l
l

n
o
t

b
e

u
p
d
a
t
e
d

i
n

c
a
s
e

o
f

c
h
a
n
g
e
s
!

SN359-1 : 2012-06
Material designation
Basis NH, Teil 1
Material No. Former design. Standard Remark Material design. Standard Remark Matching of properties:
E295 1. 0050 St 50-2 DIN EN 10025-2 - Q275 Z GB 700-88
C content 0.28 to 0.38%,
only limited weldability,
Z = Fully killed steel only is permissible,
identical
E335 1. 0060 St 60-2 DIN EN 10025-2 - Q 345 A GB T 1591-94 Fully killed steel is permissible identical
E360 1. 0070 St 70-2 DIN EN 10025-2 - Q 390 A GB T 1591-94 Fully killed steel is permissible identical
S235JR 1. 0038
St 37-2
R St 37-2
S235JRG2
DIN EN 10025-2
KV at room temperature,
unkilled not permitted
Q 235 B GB 700-88 Fully killed steel is permissible identical
S235J0 1. 0114
R St 37-3
S235J0G2
DIN EN 10025-2
KV at 0C, unkilled not
permitted
Q 235 C GB 700-88
Fully killed steel only permissible,
KV at 0C ,
similar
S235J2 1. 0117
Q St 37-3N
S235J2G3
DIN EN 10025-2
KV at -20C, unkilled not
permitted
Q 235 D GB 700-88
Fully killed or double-killed steel is
permissible,
KV at -20C ,
similar
S275JR 1. 0044
St 44-2
S275JRG2
S275JRC
DIN EN 10025-2
Q 275 Z GB 700-88
C content must be limited to 0.22%,
otherwise only limited weldability, notch
impact energy not guaranteed.
similar
Q 275 GB 700-88
C content must be limited to 0.22%, notch
do not use
Q 345 C GB T 1591-94
Fully killed steel is permissible,
KV at 0C,
similar
Q 275 GB 700-88
C content must be limited to 0.22%, notch
do not use
Q 345 D GB T 1591-94
KV at -20C.,
identical
S355JR 1. 0045 - DIN EN 10025-2
Q 345 B GB T 1591-94 Fully killed steel is permissible, identical
S355J0 1. 0553 S355J0G2 DIN EN 10025-2
permitted
Q 345 C GB T 1591-94
KV at room 0C,
identical
S355J2 1.0577 S355J2G3 DIN EN 10025-2
permitted
Q 345 D GB T 1591-94
KV at -20C.,
identical
S355N 1. 0545 StE 355 DIN EN 10025-3
normalised,
KV at -20C,
Q 345 D GB T 1591-94 KV at -20C similar
S355NL 1. 0546 TStE 355 DIN EN 10025-3
normalised
KV at -50C,
Q 345 E GB T 1591-94 KV at -40C ! similar
S420N 1. 8902 StE 420 DIN EN 10025-3
normalised
KV at -20C,
Q 420 D GB T 1591-94 KV at -20C ! similar
S420NL 1. 8912 TStE 420 DIN EN 10025-3
normalised
KV at -50C,
S460N 1. 8901 StE 460 DIN EN 10025-3
normalised
KV at -20C,
Q 460 D GB T 1591-94 KV at -20C ! similar
S460NL 1. 8903 TStE 460 DIN EN 10025-3
normalised
KV at -50C,
S620Q 1.8914 StE 620V DIN EN 10025-6 quenched & tempered 18CrMnMoB Q/ZB 61-73 Fully killed steel is permissible, similar
S690Q 1. 8931 StE690V DIN EN 10025-6 quenched & tempered Q690E/Q690D GB/T 16270-96 Fully killed steel is permissible, similar
1. 0143
German
DIN EN 10025-2
Chinese
permitted
S275J2 1. 0145
St 44-3N
S275J2G3
S275J2G3C
S275J2G4
Anhang/Appendix A1 (normativ) - Comparison of german and chinese material designation, steels
Engineering steels
Fine-grained engineering steels, weldable
St 44-3
DIN EN 10025-2
permitted
S275J0
Seite/Page 2 von/of 44
SN359-1 : 2012-06
Basis NH, Teil 1
German Chinese
P235GH+N 1.0345 - DIN EN 10028-2 normalised Q245R GB 713-1997 similar
P265GH+N 1.0425 - DIN EN 10028-2 normalised not known
P355GH+N 1.0473 - DIN EN 10028-2 normalised Q345R GB 713-1997 similar
16Mo3+N 1.5415 - DIN EN 10028-2 normalised not known
13CrMo4-5+NT
normalizied and
tempering
14Cr1MoR +N GB 713-1997 similar
13CrMo4-5 +NT or +QT
normalizied & tempered
or
quenched & tempered
14Cr1MoR +QT
13CrMo4-5 +QT quenched & tempered 14Cr1MoR +QT
C45 +C or +SH 1. 0503 C 45 DIN EN 10277-2 45 GB 699-88 Z = killed only is permissible similar
C15 +C or +SH 1. 0401 C15 DIN EN 10277-2 15 GB 699-88 Z = killed only is permissible similar
E 295GC +C or +SH 1. 0533 St 50-2 KG DIN EN 10277-2 Q 275 GB 700-88 similar
DC01 1. 0330 St 12 DIN EN 10130 08F GB 699-88 Sameness must be checked in every case similar
X20CrMoV11-1 1.4922 X 22 CrMoV 12 1 DIN EN 10222-2 1Cr11MoV GB 1221-92 similar
Heat-resisting steels
Bright steel products,
+C = cold drawn
+SH = as rolled and
turned
Bright steel products for general engineering purposes
Sheets
Flat products made of steels for pressure purpose
1.7335 - DIN EN 10028-2
GB 713-1997 similar
SN359-1 : 2012-06
Basis NH, Teil 1
German Chinese
20 GB 8163-2008
Q235A GB 8162-2008
20 GB 8163-2008 KV is not guaranted similar
Q235A GB 8162-2008 KV/J 0C = min. 27 similar
P235GH 1.0345 St 35.8 DIN EN 1016-2 normalised 20
GB 8163-2008
GB 8162-2008
KV is not nacessary similar
P355N 1.0562 StE 355/St 52.4 DIN EN 10216-3 normalised Q345D GB 8163-2008 KV/J -20C = min. 34 similar
P460NH 1.8935 - DIN EN 10216-3 normalised Q460E GB 8163-2008 KV/J -40C = min. 27 similar
E235 1.0308 St 37.4 DIN EN 10305-4 normalised Q235C GB 8162-2008 KV/J 0C = min. 27 similar
X2CrNiMo 17-12-2 1.4404 -
DIN EN 10216-5
DIN EN 10217-7
solution annealing 00Cr17Ni14Mo2 GB T 14976-94 similar
X6CrNiTi18-10 1. 4541 X10CrNiTi 18 9
DIN EN 10216-5
DIN EN 10217-7
solution annealing 0Cr18Ni10Ti GB 13296-91 similar
0Cr18Ni10Ti GB T 14975-94 similar
0Cr18Ni10Ti GB T 14976-94 similar
X6CrNiMoTi17-12-2 1. 4571 X10CrNiMoTi 18 10
DIN EN 10216-5
DIN EN 10217-7
solution annealing 0Cr18Ni12Mo2Ti GB T 14975-94 similar
0Cr18Ni12Mo2Ti GB T 14976-94 similar
normalised
1. 0255 QSt 37.0 DIN EN 10216-1
KV is not necessary
Tubes in stainless steels
1. 0254 St 37.0 DIN EN 10216-1
Pipes, tubes
normalised P235TR2
P235TR1 similar
SN359-1 : 2012-06
Basis NH, Teil 1
German Chinese
C22 +N 1. 0402 C 22 N DIN EN 10083-2 normalised 20 GB 699-88 Z = killed is permissible identical
C35 +QT 1. 0501 C 35 V DIN EN 10083-2 quenched & tempered 35 GB 699-88
Z = killed is permissible, Agreement
required for QT instead of normalising.
similar
C35E +QT 1. 1181 Ck 35 V DIN EN 10083-1 quenched & tempered 35 GB 699-88
required for QT instead of normalising. Yield
point at small nom. thickness differs from
European material.
similar
similar
European material.
similar
similar
European material.
similar
40Cr GB/T 3077-99 +QT similar
51CrV4+QT 18.159 - DIN EN 10083-1 quenched & tempered 50CrVA4 GB/T 1222 +QT similar
30CrMo GB 3077-88 Heat treatment strength to be agreed upon similar
25CrMo JB/T 6396-2006
Specification for the heavy alloy structural
steel forgings
similar
42CrMo JB/T 6396-2006
steel forgings
similar
50CrMo EZB 1184-93 similar
50CrMo JB/T 6396-2006
steel forgings
similar
34Cr2Ni2Mo EZB 1184-93 similar
34Cr2Ni2Mo JB/T 6396-2006
steel forgings
similar
30Cr2Ni2Mo JB/T 6396-2006
steel forgings
similar
Cf 35 V 1. 1183.05 Cf 35 V DIN 17212 +QT 35 GB 699-88
similar
Cf 45 V 1. 1193.05 Cf 45 V DIN 17212 +QT 45 GB 699-88
similar
Cf 53 V 1. 1213.05 Cf 55 V DIN 17212 +QT 55 GB 699-88
similar
1.6580
34 CrNiMo 6 V DIN EN 10083-1
42CrMo4+QT 1.7225 42 CrMo 4 V
+QT
30 CrNiMo 8 V DIN EN 10083-1
25 CrMo 4 V DIN EN 10083-1
+QT
1.6582
30CrNiMo8+QT
1.7228 50 CrMo 4 V DIN EN 10083-1
+QT
+QT
Quenched and tempered steels, unalloyed
Flame hardening steels
Quenched and tempered steels, alloyed
50CrMo4+QT
34CrNiMo6+QT
25CrMo4+QT 1.7218
DIN EN 10083-1 +QT
SN359-1 : 2012-06
Basis NH, Teil 1
German Chinese
16MnCr5+TH 1.7131 16 MnCr 5 BF DIN EN 10084 20CrMnTi GB 3077-88 similar
16MnCr JB T 6396-92 similar
20MnCr5+TH 1.7147 20 MnCr 5 BF DIN EN 10084 20CrMnTi GB 3077-88 similar
20MnCr JB T 6396-92 similar
18CrNiMo7-6 1.6587 17 CrNiMo 6 BF DIN EN 10084 17Cr2Ni2Mo JB/T 6396-92 similar
14CrMoV6-9 1.7735 - SEL 2003
32Cr3MoVA
38CrMoAlA
? +QT and nitiding similar
34CrAlMo5-10 1.8507 - DIN EN 10085 38CrMoAl GB/T 3077-99 similar
60WCrV 7 1.2550 60 WCrV7 DIN EN ISO 4957 6 Cr W 2 Si GB 1299-85 similar
102Cr6 1.2067 100Cr6 DIN EN ISO 4957 Cr2 GB 1299-85 similar
X35CrMo17 1.4122 - - HRC 54+/-2 4Cr13 GB 1220 HRC min. 50 similar
21 CrMoV 5-11+QT 1. 8070 - - +QT 12Cr1MoV+QT GB/T 3077 +QT similar
X20CrMoV11-1 1.4922 X 20 CrMoV 12 1 DIN EN 10222-2 1Cr11MoV GB 1221-92 similar
20 GB 699-88 Notch impact energy not guaranteed do not use
16MnDR GB 3531-96 similar
20Mn2 GB 3077-88 similar
C22 1.0402 C 22 DIN EN 10250-2 20 GB 699-88 Z = killed is permissible similar
20Mn5 1.1133 20 Mn 5 DIN EN 10250-2 20Mn2 GB 3077-99 similar
20SiMn GB 3077-99 similar
28Mn6 1.1170 30Mn5 DIN EN 10250-2 +QT 35SiMn
GB/T 3077-99
JB/T 6396-92
+QT similar
C35E 1.1181 Ck 35 DIN EN 10250-2 35 GB 699-88 Z = killed is permissible identical
45H GB 5216-85 similar
25CrMo JB/T 6396-2006
steel forgings
similar
35CrMo JB/T 6396-2006
steel forgings
similar
34CrMo4+QT 1.7220 34 CrMo 4 DIN EN 10250-3 +QT
+QT 25CrMo4+QT 1.7218 25 CrMo 4 V DIN EN 10083-1
Steels for forgings
S355J2G3 1.0570 St 52-3 DIN EN 10250-2
Tool steel
Nitriding steels
Case hardening steels
SN359-1 : 2012-06
Basis NH, Teil 1
German Chinese
42CrMo JB/T 6396-2006
steel forgings
similar
50CrMo EZB 1184-93 similar
50CrMo JB/T 6396-2006
steel forgings
similar
30Cr2Ni2Mo JB/T 6396-2006
steel forgings
similar
34Cr2Ni2Mo JB/T 6396-2006
steel forgings
similar
33NiCrMoV14-5 1.6956 33 NiCrMoV 14 5 DIN EN 10250-3 +QT Not known Not known -
32CrMo12 1.7361 - SEW 550 +QT 30Cr2Ni2Mo EZB 1184-93 +QT similar (~)
X20Cr13 1.4021 X 20 Cr 13 DIN EN 10250-4 2Cr13 or 3Cr13 GB/T 1220-92 similar
2Cr13 or 3Cr13 GB 1221-92 similar
2Cr13 or 3Cr13 GB 8732-88 similar
X17CrNi16-2 1.4057 X 17 CrNi 16 2 DIN EN 10250-4 1Cr17Ni2 GB/T 1220-92 similar
1Cr17Ni2 GB 1221-92 similar
X4CrNi18-10 1.4301 X 5 CrNi 18 9 DIN EN 10250-4 solution annealing 0Cr18Ni9 GB/T 1220-92 similar
X6CrNiTi18-10 1.4541 X 10 CrNiTi 18 9 DIN EN 10250-4 solution annealing 0Cr18Ni10Ti GB/T 1220-92 similar
0Cr18Ni10Ti GB 1221-92 similar
X6CrNiMoTi17-12-2 1.4571 X 10 CrNiMoTi 18 10 DIN EN 10250-4 solution annealing 0Cr18Ni12Mo2Ti GB/T 1220-92 similar
X5CrNiMo17-12-2 1.4401 X 5 CrNiMo17 12 2 DIN EN 10250-4 solution annealing 0Cr17Ni12Mo2 GB/T 1220 / 1221-92 similar
00Cr17Ni14Mo2 GB/T 1220-92 similar
X4CrNiMo16-5-1 1.4418 - DIN EN 10250-4 solution annealing Not known Not known -
+QT
50CrMo4+QT 1.7228 50 CrMo 4 V DIN EN 10083-1
+QT 34CrNiMo6+QT 1.6582 34 CrNiMo 6 V DIN EN 10083-1
+QT
30CrNiMo8+QT 1.6580 30 CrNiMo 8 V DIN EN 10083-1
Steels for forgings (continued)
42CrMo4+QT 1.7225 42 CrMo 4 V DIN EN 10083-1 +QT
SN359-1 : 2012-06
Basis NH, Teil 1
German Chinese
X20Cr13 1.4021 X 20 Cr 13 DIN EN 10088-1 to 3 2Cr13 GB/T 1220-92 similar
X46Cr13 1.4034 X 46 Cr 13 DIN EN 10088-1 to 3 HRC min. 55 4Cr13 GB/T 1220-92 HRC min 50 similar
X17CrNi16-2 1.4057 X 17 CrNi 16 2 DIN EN 10088-1 to 3 1Cr17Ni2 GB/T 1220-92 similar
1Cr17Ni2 (-R) GB T 4240-93 similar
1Cr17Ni2 GB T 4231-93 similar
ML1Cr17Ni2 GB 4232-93 similar
X4CrNi18-10 1.4301 X 5 CrNi 18 9 DIN EN 10088-1 to 3 0Cr18Ni9 GB/T 1220-92 similar
X5CrNiMo17-12-2 1.4401 X 5 CrNiMo17 12 2 DIN EN 10088-1 to 3 solution annealing 0Cr17Ni12Mo2 GB/T 1220-92 similar
X6CrNiTi18-10 1.4541 X 10 CrNiTi 18 9 DIN EN 10088-1 to 3 solution annealing 0Cr18Ni10Ti GB/T 1220-92 similar
X6CrNiMoTi17-12-2 1.4571 X 10 CrNiMoTi 18 10 DIN EN 10088-1 to 3 solution annealing 0Cr18Ni12Mo2Ti GB T 4237-92 similar
Stainless steels
SN359-1 : 2012-06
Basis NH, Teil 1
GS200 1. 0449 GS-38N DIN EN 10293 normalised ZG 200 - 400 GB 11352-89
For weldet parts the C-content must be <
0,18%
similar
GS240 1.O445 GS-45N DIN EN 10293 normalised ZG 230 - 450 GB 11352-89
0,23%
similar
ZGD 270 - 480 GB T 14408-93
No composition specification, only P and S
max. 0.040 each
do not use
GE300 1.O558 GS-60N DIN EN 10293 normalised ZG 310 - 570 GB 11352-89
Important! C content 0.50 to 0.60 %, only
limited weldability.
similar
ZG340 - 640 GB 11352-89
similar
ZGD 345 - 570 GB T 14408-93
max. 0.040 each
similar
ZGD 410 - 620 GB T 14408-93
max. 0.040 each
similar
G20Mn5 +N or +QT 1 .6220 GS-20Mn5V DIN EN 10293 quenched & tempered ZG 20 Mn JB T 6402-92 similar
GS-52N 1.O552 GS-52N DIN 1681 normalised ZG 270 - 500 GB 11352-89
do not use
ZGD 290 - 510 GB T 14408-93
max. 0.040 each
similar
ZG 310-570 GB 11352-89 do not use
G28Mn6 +QT1 or QT2 1. 1165 GS-30Mn5V DIN EN 10293 quenched & tempered ZG 35 Mn+QT JB T 6402-92 No comparison for QT2 similar
G26 CrMo4 +QT1 or +QT2 1. 7221 GS-25 CrMo4V DIN EN 10293 quenched & tempered ZG 35 Cr1Mo JB T 6402-92
0,30%
similar
G42 CrMo4 +QT1 or QT2 1. 7231 GS-42 CrMo4V DIN EN 10293 quenched & tempered ZG 42Cr1Mo JB T 6402-92 similar
G35CrNiMo6-6 +N or +QT1 or
QT2
1. 6582 GS-34CrNiMo6V DIN EN 10293 quenched & tempered ZG 34 Cr2Ni2Mo JB T 6402-92 similar
GS-34 CrMo4V 1. 7220 GS-34 CrMo4V DIN 17205 quenched & tempered ZG 35Cr1Mo JB T 6402-92 similar
G42CrMo4 1. 7231 GS-42CrMo4 SEW 835 quenched & tempered ZG 42 Cr1Mo JB T 6402-92 similar
G50CrMo4 1. 7232 GS-50CrMo4 SEW 835 quenched & tempered ZG 50 Cr1Mo JB T 6402-92 similar
Anhang/Appendix A2 (normativ) - Comparison of german and chinese material designation, cast steels
German Chinese
General purpose cast steel
Quenched and tempered steel castings
Flame and induction hardening steel castings
SN359-1 : 2012-06
Basis NH, Teil 1
German Chinese
GP240GR+N 1.O621 GS-C25N DIN EN 10213-2 normalised ZG 230-450 EZB 1165-93 similar
ZG 20SiMn JB T 4297-86 similar
GP240GH+QT 1.O619 GS-C25V DIN EN 10213-2 quenched & tempered ZG 230-450 EZB 1165-93 +QT similar
ZG 20SiMn JB T 4297-86 +QT similar
G20Mo5+QT 1. 5419 GS-22Mo4V DIN EN 10213-2 quenched & tempered ZG 20MnMo JB T 6402-92 +QT similar
G17CrMo5-5+QT 1. 7357 GS-17CrMo55V DIN EN 10213-2 quenched & tempered ZG 20CrMoV JB / T 7024-93
C content higher, V alloyed, Rm and Re
identical
similar
G17CrMoV5-10+QT 1. 7706 GS-17CrMoV5 11V DIN EN 10213-2 quenched & tempered
ZG 15Cr1Mo1V
ZG17Cr1Mo1VG
JB / T 7024-93
GB/T 16253-1996
+QT ()
similar
similar
GX23CrMoV12-1+QT 1. 4931 G-X22CrMoV12 1V DIN EN 10213-2 quenched & tempered ZG23Cr12Mo1NiVG GB/T16253-1996 +QT () similar
GX 120Mn12 1. 3401 - without standard - ZG MN 13-1 GB 5680-98 similar
Not known - without standard ZG MN 13-2 GB 5680-98 -
Manganese steel castings, austenitic
EZB-Standards are work-standards from
CHINA NATIONAL ERZHONG GROUP
Heat-resistant steel castings
SN359-1 : 2012-06
Basis NH, Teil 1
EN-GJL-200 EN-JL1030 GGL-20 DIN EN 1561 - HT20 - 40 GB 9439-88 identical
HT 200 EZB 1173-94 similar
GJS-400-18U 1062 GGG-40 DIN EN 1563 U = test bar attached Not known Not known -
GJS-400-15U 1072 GGG-40 DIN EN 1563 U = test bar attached QT 400-15 GB 1348-88 identical
EN-GJMW-360-12 EN-JM 1020 GTW-S 38-12 DIN EN 1562 Not known Not known -
EN-GJMW-400-5 EN-JM 1030 GTW-40-05 DIN EN 1562 Not known Not known -
Anhang/Appendix A3 (normativ) - Comparison of german and chinese material designation, cast irons
Malleable cast iron
German Chinese
Grey cast iron
Spheroidal graphite cast iron
SN359-1 : 2012-06
Basis NH, Teil 1
GK-CuSn10Zn - GK-S1 DIN EN 1982 ZCuSn10Zn2 GB/T 1176-1987 similar
CuSn7Zn4Pb7-C-GS CC493K-GS G-CuSn7ZnPb DIN EN 1982 ZCuSn7Zn4Pb6 EZB 1179-93 similar
CuSn7Zn4Pb7-C-GZ CC493K-GZ GZ-CuSn7ZnPb DIN EN 1982 ZCuSn7Zn4Pb6 EZB 1179-93 similar
CuSn7Zn4Pb7-C-GC CC493K-GC GC-CuSn7ZnPb DIN EN 1982 ZCuSn7Zn4Pb6 EZB 1179-93 similar
CuSn10-C-GS CC480K-GS GB-CuSn10 DIN EN 1982 ZCuSn10P1 EZB 1179-93 similar
CuSn10-C-GZ CC480K-GZ GB-CuSn10 DIN EN 1982 ZCuSn10P1 EZB 1179-93 similar
CuSn10-C-GC CC480K-GC GB-CuSn10 DIN EN 1982 ZCuSn10P1 EZB 1179-93 similar
CuSn12-C-GS CC483K-GS G-CuSn12 DIN EN 1982 ZCuSn12Pb1 EZB 1179-93 similar
CuSn12-C-GZ CC483K-GZ GZ-CuSn12 DIN EN 1982 ZCuSn12Ni2 EZB 1179-93 similar
ZCuSn10Pb1 Not known do not use
CuSn12-C-GC CC483K-GC GC-CuSn12 DIN EN 1982 ZCuSn12Ni2 EZB 1179-93 similar
CuSn12Ni2-C-GS CC484K-GS G-CuSn12Ni DIN EN 1982 ZCuSn12Ni2 EZB 1179-93 similar
CuSn12Ni2-C-GZ CC484K-GZ GZ-CuSn12Ni DIN EN 1982 ZCuSn12Ni2 EZB 1179-93 similar
CuSn12Ni2-C-GC CC484K-GC GC-CuSn12Ni DIN EN 1982 ZCuSn12Ni2 EZB 1179-93 similar
CuSn11Pb2-C-GS CC482K-GS G-CuSn12Pb DIN EN 1982 ZCuSn12Pb1 EZB 1179-93 similar
CuSn11Pb2-C-GZ CC482K-GZ GZ-CuSn12Pb DIN EN 1982 ZCuSn12Pb1 EZB 1179-93 similar
CuSn11Pb2-C-GC CC482K-GC GC-CuSn12Pb DIN EN 1982 ZCuSn12Pb1 EZB 1179-93 similar
devagleit
TM
dg02 Basimaterial 2.1061.01 CuSn12Pb -
Product from Federal
Mogul (www.deva.de)
DF-5 -
Product from Dalian Fangyuan
Composite Material Bearings
Co.Ltd.(www.dfbearing.cn)
similar
GS =sand casting
GZ = centrifugal casting
GC = continuously cast
material
Anhang/Appendix A4 (normativ) - Comparison of german and chinese material designation, non-ferrous metals
German Chinese
Copper-tin-zinc cast alloys (red brass)
Copper-tin cast alloys (tin bronze)
SN359-1 : 2012-06
Basis NH, Teil 1
German Chinese
CuSn10Pb10-C-GS CC495K-GS G-CuPb10Sn DIN EN 1982 ZCuPb10Sn10 GB/T 1176-1987 similar
CuSn10Pb10-C-GZ CC495K-GZ GZ-CuPb10Sn DIN EN 1982 ZCuPb10Sn10 GB/T 1176-1987 similar
CuAl10Fe5Ni5-C-GS CC333G-GS G-CuAl10Ni DIN EN 1982 ZCuAl10Ni6Fe5 EZB 1179-93 similar
CuAl10Fe5Ni5-C-GZ CC333G-GZ GZ-CuAl10Ni DIN EN 1982 ZCuAl10Ni6Fe5 EZB 1179-93 similar
AMPCO 18-23 (GS) ZCuAl10Fe3
AMPCO 18-23 (GZ) ZCuAl10Fe3
CuZn35Mn2Al1Fe1-GS CC765-GS G-CuZn35Al1 DIN EN 1982 ZCuZn35Al1Fe1Mn2 EZB 1179-93 similar
CuZn35Mn2Al1Fe1-GZ CC765-GZ GZ-CuZn35Al1 DIN EN 1982 ZCuZn35Al1Fe1Mn2 EZB 1179-93 similar
CuZn34Mn3Al2Fe1-C-GS CC764-GS G-CuZn34Al2 DIN EN 1982 ZCuZn34Al2Fe2Mn3 EZB 1179-93 similar
CuZn34Mn3Al2Fe1-C-GZ CC764-GZ GZ-CuZn34Al2 DIN EN 1982 ZCuZn34Al2Fe2Mn3 EZB 1179-93 similar
CuZn25Al5Mn4Fe3-C-GS CC762-GS G-CuZn25Al5 DIN EN 1982 ZCuZn25Al5Fe3Mn4 EZB 1179-93 similar
CuZn25Al5Mn4Fe3-C-GZ CC762-GZ GZ-CuZn25Al5 DIN EN 1982 ZCuZn25Al5Fe3Mn4 EZB 1179-93 similar
CuZn37Mn3Al2PbSi-R540 CW713R-R540 CuZn40Al2F54 DIN EN 12164 Not known Not known -
Main-Metall*
Produkt from Main-
Metall_Foundry
(www.main-
metall.com)
Not known Not known -
White bronze
Not according to standard, White bronze with special guaranteed
values.
Not according to standard, CuAl alloy with special guaranteed values.
Copper-zinc cast alloys (cast special brass)
GS =sand casting
material
Product from APMCO
Metal Deutschland
GmbH
(www.ampcometal.net
GS =sand casting
material
EZB 1179-93
similar, see list with material
properties!
Copper-lead-tin cast alloys
GS =sand casting
material
Copper-aluminium cast alloys
SN359-1 : 2012-06
Anhang/Appendix B1 (normativ) - Comparison of german and chinese material properties, steels
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
mm MPa MPa % % HBW C Si Mn P S Cr Mo Ni N other
16 295
16 - 40 285
40 - 63 275 19
St 50-2 63 - 80 265
Fe 490-2 80 - 100 255
100 - 150 245 450-610 16
150 - 200 235
200 - 250 225
16 275 20
16 - 40 265 19
40 - 60 255 18
60 - 100 245 17
100 - 150 235 16
>150 225 15
16 335
16 - 40 325
40 - 63 315 570-770 15
St 60-2 63 - 80 305
Fe 590-2 80 - 100 295
100 - 150 275 550-710 12
150 - 200 265 540-710
200 - 250 255
16 345
16 - 35 325
35 - 50 295
50 - 100 275
Material
+N
Group Material designation Standard Mat.-
No.
E 295 +N DIN EN 10025-2 1.0050
Former
designation
Heat
treatment
470-630 21 - - 0,20
Unkilled not permitted
Notch impact energy not guaranteed.
14
11
-
- -
0,55
1,00
-
1,60
0,045 0,045
V 0,02-0,15
Nb0,015-
0,060
Ti0,02-0,20
Z = Fully killed steel is permissible
+N Normalised is permissible
490-630
E 335 +N DIN EN 10025-2 1.0060
Q275 Z GB 700-88
Q345A GB 1591-94
- - +N
16
- - 0,012 - 0,045 0,045 -
+N
20
18
15
-
470-610
440-610
0,055 0,055 0,012 - - -
J C
% max. or range min. or range
Chemical composition Mechanical properties
- -
- -
0,28 -
0,38
-
-
0,35
0,50 -
0,80
0,05 0,045
Notice
N
o
n
-
a
l
l
o
y

s
t
r
u
c
t
u
r
a
l

s
t
e
e
l
s
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
16 360
16 - 40 355
40 - 63 345 10
63 - 80 335
80 - 100 325
100 - 150 305 650-830 8
150 - 200 295
200 - 250 285
16 390
16 - 35 370
35 - 50 350
50 - 100 330
3 - 16 235 26
16 - 40 225 26
40 - 63 215 25
RSt 37-2 63 - 80 215 24
Fe 360 B-FN 80 - 100 215 24
S235JRG2 100 - 150 195 22
150 - 200 185 21
200 - 250 175 21
16 235 26
16-40 225 25
40-60 215 24
60-100 205 23
100-150 195 22
>150 185 21
0,12 -
0,20
0,30
V 0,02-0,15
Nb0,015-
0,060
Ti0,02-0,20
E 360 +N DIN EN 10025-2 1.0070
St 70-2
Fe690-2
+N
670-900
11
9 0,045 - - - - - -
Q390A GB 1591-94 490-650 19
0,01 0,045 - - -
- - -
640-830 7
0,045 0,30 0,70 0,20 0,55
1,00
-
1,60
0,045
27
-
20
20
Unkilled not permitted -
27 -
0,014 Cu max. 0,60 1,50
23
S235JR +N
Q235B
DIN EN 10025-2 1.0038
375-460
340-470
+N
GB 700-88
0,30
-
0,70
320-470
0,19
20 0,045 0,045
- - 0,045 0,045 -
0,23
N
o
n
-
a
l
l
o
y

s
t
r
u
c
t
u
r
a
l

s
t
e
e
l
s
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
3 - 16 235 26
16 - 40 225 26
40 - 63 215 25
63 - 80 215 24
80 - 100 215 24
100 - 150 195 22
150 - 200 185 21
200 - 250 175 21
16 235 26
16-40 225 25
40-60 215 24
60-100 205 23
100-150 195 22
>150 185 21
3 - 16 235 26
16 - 40 225 26
40 - 63 215 25
63 - 80 215 24
80 - 100 215 24
100 - 150 195 22
150 - 200 185 21
200 - 250 175 21
16 235 26
16-40 225 25
40-60 215 24
60-100 205 23
100-150 195 22
>150 185 21
3 - 16 275 21
16 - 40 265 21
40 - 63 255 20
St 44-2 63 - 80 245 19
Fe 430 B 80 - 100 235 19
S275JRG2 100 - 150 225 400-540 19
150 - 200 215 380-540 18
200 - 250 205 18
16 275 20 -
16-40 265 19 -
40-60 255 18 -
60-100 245 17 -
100-150 235 16 -
>150 225 15 -
Q295B GB/T 1591-94 16 295
16-35 275
35-50 255
50-100 235
20 0,16 0,55
0,80 -
1,50
0,12 -
0,20
0,30
S235J0 +N DIN EN 10025-2 1.0114
340-470
- 0,19 - 1,50 0,04 0,04 - - Cu max. 0,60 0 27 - 0,014 Unkilled not permitted
320-470
0,12 -
0,20
0,30
0,30
-
0,70
0,045 0,045
34
Q235C GB 700-88
S235J2 +N DIN EN 10025-2 1.0117
340-470
-
0
0,045
DIN EN 10025-2 1.0044
Q275 Z GB 700-88 0,05 490-630
320-470
+N
+N
0,28
-
0,38
0,35
0,50
-
0,80
1,50
-
410-560
27
23
27
27
375-460 -
23
Q235D GB 700-88 375-460
0,25
- - +N
- 27
- -
0,04
0,035 0,035
1,60 0,045 0,045
0,30
-
0,70
0,045 -20
20
S275JR +N
-
20
390 - 570
C content must be limited to 0.22%, otherwise only
0,04
Cu max. 0,60 Fully killed steel is permissible
0,24
-
0,045
- -20 0,19
Unkilled not permitted 0,014 Cu max. 0,60
N
o
n
-
a
l
l
o
y

s
t
r
u
c
t
u
r
a
l

s
t
e
e
l
s
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
3 - 16 275 21
16 - 40 265 21
40 - 63 255 20
63 - 80 245 19
80 - 100 235 19
100 - 150 225 400-540 19
150 - 200 215 380-540 18
200 - 250 205 18
16 275 20
16-40 265 19
40-60 255 18
60-100 245 17
100-150 235 16
>150 225 15
3 - 16 275 21
16 - 40 265 21
40 - 63 255 20
St 44-2 63 - 80 245 19
Fe 430 B 80 - 100 235 19
S275JRG2 100 - 150 225 400-540 19
150 - 200 215 18
200 - 250 205 18
16 275 20
16-40 265 19
40-60 255 18
60-100 245 17
100-150 235 16
>150 225 15
3 - 16 355
16 - 40 345
40 - 63 335 19
63 - 80 325
80 - 100 315
100 - 150 295 18
150 - 200 285
200 - 250 275
16 345
16-35 325
35-50 315
50-100 275
0,04 0,20 0,55
Cu max. 0,60
20
- 20
- 34 20
V 0,02-0,15
Nb0,015-
0,060
Ti0,02-0,20
27 -
S355JR +N DIN EN 10025-2 1.0045 - +N Unkilled not permitted
22
1,00
-
1,60
0,04
- -
0,045 0,27 1,70 0,045
Q345B GB 1591-94 Normalized
17
18 0,014
27 0 0,21 -
Fully killed steel is permissible 0,21 0,035 - 1,60 0,035 -
S275J2 +N Cu max. 0,60
Q275Z
-20
0,60
0,04 0,04
0,05 0,045 490-630
380-540
27
1.0145
410-560
490-630 -
+N
0,50
-
0,80
DIN EN 10025-2
0,35 GB 700-88
0,28
-
0,38
0,50
-
0,80
0,05 0,045
-
470-630
- -
450-600
0,012 Cu max. 0,60 Unkilled not permitted
470-630
-
0,35
410-560
1,60
0,28
-
0,38
S275J0 +N DIN EN 10025-2 1.0143
Q275Z GB 700-88
+N
N
o
n
-
a
l
l
o
y

s
t
r
u
c
t
u
r
a
l

s
t
e
e
l
s
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
3 - 16 355
16 - 40 345
40 - 63 335 19
63 - 80 325
80 - 100 315
100 - 150 295
150 - 200 285
200 - 250 275
16 345
16-35 325
35-50 315
50-100 275
3 - 16 355
16 - 40 345
40 - 63 335 19
63 - 80 325
80 - 100 315
100 - 150 295
150 - 200 285
200 - 250 275
100 315 490 20 35
100 - 250 275 18 30
250 - 500 265 18 27
16 345
16-35 325
35-50 295
50-100 275
3 - 16 355
16 - 40 345
40 - 63 335 19
63 - 80 325
80 - 100 315
100 - 150 295
150 - 200 285
200 - 250 275
16 345
16-35 325
35-50 295
50-100 275
-
Normalized
-40
0,55
0,025
470-630 27 1,00
-
1,60
0,18
V 0,02-0,15
Nb0,015-
0,060
Ti0,02-0,20
Al 0,015
0,23
27
+N
V 0,02-0,15
Nb0,015-
0,060
Ti0,02-0,20
Al 0,015
0,035 S355J0 +N DIN EN 10025-2 1.0553
Q345C GB 1591-94
470-630 22
450-600
17
18
0,012 1,60 0,035
Cu max. 0,60 -
470-630
20
-
0,035 0,18 0,55
1,00
-
1,60
0,035
27 0 0,24 0,55
Cu max. 0,60
S355K2 +N DIN EN 10025-2
Steel for forgings
- 27 -20 DIN EN 10025-2 1.0577
470-630
18
+N
17
0,035
0,23
0,22 0,55 1,6 0,035
1,70
0,08 0,3
Al min. 0,020
Cr+Mo+Ni
max. 0,48
Cu max. 0,60 Fully killed steel is permissible
450-600
0,035
33
470-630
-30
1,70 0,60
20
-
17
18
22 -
S355J2 +N
S355J2 +N
-20
0,035
0,24
Q345D
1,00
-
1,60
- 34
20
22
Normalized
-
1.0570
0
0,03
0,035 0,3
0,03
Fully killed steel is permissible
470-630
0,18
0,035
+N
GB 1591-94
DIN EN 10250-2
0,24
0,60
1.0596
Q345E GB 1591-94
-20
450 - 600
-20
450
V 0,02-0,15
Nb0,015-
0,060
Ti0,02-0,20
AL0,015
34
0,55
0,025
Normalized
+N
N
o
n
-
a
l
l
o
y

s
t
r
u
c
t
u
r
a
l

s
t
e
e
l
s
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
16 355 270
16-40 345 AL>0,020%
40-63 335 Cu<0,35%
63-80 325 Nb<0,05%
80-100 315 V <0,12%
100-150 295
150-200 285
200-250 275 Ti<0,05%
16 345
16-35 325
35-50 295
50-100 275
16 355 270
16-40 345 AL>0,020%
40-63 335 Cu<0,35%
63-80 325 Nb<0,05%
80-100 315 V <0,12%
100-150 295
150-200 285
200-250 275 Ti<0,05%
16 345
16-35 325
35-50 295
50-100 275
16 420
16-40 400 AL>0,020%
40-63 390 Cu<0,55%
63-80 370 Nb<0,05%
80-100 360 V <0,20%
100-150 340
150-200 330
200-250 320 Ti<0,05%
16 420
16-35 400
35-50 380
50-100 360
0,30
500-650
520-680
520-680 Normalized
0,02-0,2 V
0,015-0,06
Nb
0,02-0,2 Ti
Al>0,015
KV at -20C!
0,03 0,03 0,40 0,70
KV at -20C!
KV at -20C 0,025
1,00 -
1,70
KV only at -40C!
KV at -50C
- 40 -20
20
0
-10
-20
0,20 0,60
21
450-600
470-680
22
-
20
0
-10
-20
-30
-40
-50
63
55
51
47
40
31
27
34 -20
18
- 22
-
KV at -20C!
- 34 -20 0,18
0,03 0,025 0,30
0,20
Q345E GB 1591-94
S 355 NL +N DIN EN 10025-3
Q420D GB 1591-94
DIN EN 10025-3 S 420 N +N
Q420D GB 16270-96
0,50
0,90 -
1,65
1,00
-
1,60
0,025
0,03
St E 420
TStE 355
Q345D GB 1591-94 Normalized
S 355 N +N DIN EN 10025-3 1.0545 StE 355 0,025 0,30
19
55
47
43
40
0,10 0,50 0,20
0,02-0,2 V
0,015-0,06
Nb
0,02-0,2 Ti
Al>0,015
0,55
1,00
-
1,60
0,03 0,03
0,55
0,015 0,025
470-680
470-630
-
55
47
43
40
22
22
21
450-600
0,015
0,03 0,50
0,90 -
1,65
27
0,20 0,50
-40 0,18
19 - 0,55
1,00
-
1,70
0,10 0,80
20
0
-10
-20
520-670
50 420
50-100
470-630
0,02-0,2 V
0,015-0,06
Nb
0,02-0,2 Ti
Al>0,015
0,55
1,00
-
1,60
0,70
max. 0,10 V
max. 0,06 Nb
0,20 Ti
0,20
0,025
0,03 0,03
0,30 0,10
420
18 0,18
Normalized
1.0546
1.8902
Normalized
+N
+N
+N
W
e
l
d
a
b
l
e

f
i
n
e

g
r
a
i
n

s
t
r
u
c
t
u
r
a
l

s
t
e
e
l
s
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
16 420
16-40 400 AL>0,020%
40-63 390 Cu<0,55%
63-80 370 Nb<0,05%
80-100 360 V <0,20%
100-150 340
150-200 330
200-250 320 Ti<0,05%
16 420
16-35 400
35-50 380
50-100 360
16 460
16-40 440 AL>0,020%
40-63 430 Cu<0,55%
63-80 410 Nb<0,05%
80-100 400 V <0,20%
100-150 380
150-200 370
200-250 - - Ti<0,05%
16 460
16-35 440
35-50 420
50-100 400
16 460
16-40 440 AL>0,020%
40-63 430 Cu<0,55%
63-80 410 Nb<0,05%
80-100 400 V <0,20%
100-150 380
150-200 370
200-250 - - Ti<0,05%
16 460
16-35 440
35-50 420
50-100 400
0,70
0,80 0,025
0,70
0,02-0,2 V
0,015-0,06
Nb
0,02-0,2 Ti
Al>0,015
KV at -20C
50 460
0,70
0,20 0,55
1,00
-
1,70
17 - 27 -40 0,70
0,02-0,2 V
0,015-0,06
Nb
0,02-0,2 Ti
Al>0,015
KV only at -40C!
0,025 0,025 0,70
0,10 0,80
Q460E GB 1591-94 Normalized
50 420
50-100 420
27
520-680
550-720
530-700
550-710
0,30 0,70
550-720
+N S 460 NL +N DIN EN 10025-3 1.8903 St E 460
550-720
-
63
55
51
47
40
31
27
Q460E GB 16270-96 Normalized 520-670 18 -
0,025 0,30
-20 0,20
1,00 -
1,70
0,03 0,025 0,20
0,55
1,00
-
1,60
0,025 0,025 0,18
Q460D GB 1591-94 Normalized 0,55
1,00
-
1,70
0,03 0,03
40
0,30
20
0
-10
-20
-30
-40
-50
0,30
-40
max. 0,10 V
max. 0,06 Nb
0,20 Ti
KV at -20C!
17
0,20 0,70 0,18
KV at -20C
0,20
KV at -50C
530-700
max. 0,10 V
max. 0,06 Nb
0,20 Ti
KV only at -40C!
17 - 34
0,10
0,20 0,60
1,00 -
1,70
50-100 440
17
-
1.8901 St E 460 +N
550-720
-
0,18
TSt E 420 +N
55
47
43
40
20
0
-10
-20
0,55
520-680
19
-
18
500-650
0,55 19 - 27 -40
420
50-100 420
0,20 Normalized
0,80 0,10 KV at -50C
1,00 -
1,70
0,025 0,02 0,30 0,025
18 27
KV only at -40C!
1,00
-
1,60
0,025
Q420E GB 1591-94
1,00
-
1,70
0,02-0,2 V
0,015-0,06
Nb
0,02-0,2 Ti
Al>0,015
KV only at -40C!
0,025 0,025 0,40
63
55
51
47
40
31
27
20
0
-10
-20
-30
-40
-50
0,20 0,60
0,02 0,025
-40 Normalized 520-670 -
50
17 0,55
1,00
-
1,60
0,03 0,03 -20
Q420E GB 16270-96
S 420 NL +N DIN EN 10025-3 1.8912
S 460 N +N DIN EN 10025-3
Q460D GB 16270-96
0,60
max. 0,10 V
max. 0,06 Nb
0,20 Ti
0,20 0,70 0,025 0,30
Normalized
W
e
l
d
a
b
l
e

f
i
n
e

g
r
a
i
n

s
t
r
u
c
t
u
r
a
l

s
t
e
e
l
s
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
3 - 50 620
50 - 100 580
100 - 150 560 650-830
18CrMnMoB Q/ZB 61-73 +QT 100-300 735 883 13 40 269-302
0,17 -
0,23
0,20 -
0,40
1,20 -
1,50
0,03 0,03
1,50 -
1,80
0,45 -
0,55
B 0,001-
0,0035
300-500 686 834 13 40 255-286
500-800 588 785 13 40 241-286
3 - 50 620
50 - 100 580
100 - 150 560 650-830
3 - 50 690 770-940
50 - 100 650 760-930
100 - 150 630 710-900
3 - 50 690 770-940
50 - 100 650 760-930
100 - 150 630 710-900
DIN EN 10025-6 1.8931
H
i
g
h

y
i
e
l
d

s
t
r
e
n
g
t
h

s
t
r
u
c
t
u
r
a
l

s
t
e
e
l
s
0,55
1,00
-
1,60
770-940 14 Q 690 E GB 16270-96 +QT
50 690
0,18 0,025 - 27 -40
Cu 0,60
Nb0,06
Ti0,05
B0,005
KV at -40C
max. 0,10 V
max. 0,06 Nb
0,20 Ti
0,003 B
KV at -40C!
50-100 670
0,025 0,80 0,60 1,20
0,20 0,025 0,015 2,00 0,025
Q 690 D GB 16270-96 +QT
1,50 0,015
50 690
S 690 Q +QT
1,20 0,60 1,50 0,18 0,55
1,00
-
1,60
0,03 - 40 -20 0,03
Q 620 E GB 16270-96 +QT
StE 690 V
S 690 QL DIN EN 10025-6 0,80
max.
1,70
30 -40
15
1.8928
max. 0,10 V
max. 0,06 Nb
0,20 Ti
0,003 B
0,025 - 27 -40 0,025 0,80 0,60 1,20
14 -
+QT
30 -20
14
50-100 670
S 620 QL DIN EN 10025-6 1.8927 TStE 620 V
700-890
15 - 30
-40
700-890
15
49
J/cm2
20
2,00 0,20 0,80
max.
1,70
0,025 0,015 0,70 1,50 - 30 +QT
KV at -20C S 620 Q DIN EN 10025-6 1.8914 StE 620 V +QT 0,70 2,00 0,025
Cu 0,60
Nb0,06
Ti0,05
B0,005
0,025 0,015 1,50
-20 0,18 0,55
0,80
max.
1,70
-20 0,20
1,00
-
1,60
50-100
40 0,60 1,20
max. 0,10 V
max. 0,06 Nb
0,20 Ti
0,003 B
KV at -20C!
KV at -20C
KV at -40C!
620
720-890
50
0,18 0,55
1,00
-
1,60
50-100 600
0,70 2,00 0,025 0,20
1,50 0,70
0,80
max.
1,70
0,025
max. 0,10 V
max. 0,06 Nb
0,20 Ti
0,003 B
KV at -20C!
600
720-890 15
50 620
0,03
770-940
0,03 0,80 Q 620 D GB 16270-96 +QT -
0,025
Cu 0,60
Nb0,06
Ti0,05
B0,005
KV at -40C
Cu 0,60
Nb0,06
Ti0,05
B0,005
TStE 690 V 14 -
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
16 235
16-40 225
40-60 215
60-100 200
100-150 185 350-480
150-250 170 340-480
3-16 245
16-36 235
36-60 225
60-100 205 390-510
100-150 185 380-500
16 265
16-40 255
40-60 245
60-100 215
100-150 200 400-530
150-250 185 390-530
not known
16 355
16-40 345
40-60 335
60-100 315 490-630
100-150 295 480-630
150-250 280 470-630
3-16 345 510-640
16-36 325 500-630
36-60 315 490-620
60-100 305 490-620
100-150 285 480-610
150-200 265 470-600
21
20
34 0 0,55
1,20-
1,60
0,025 +N
510-650
20 27 -20
Alges 0,020
Cu 0,30
Nb 0,040
Ti max. 0,03
V 0,02
0,012 +N 1.0,473 DIN EN 10028-2 P355GH+N
0,10-
0,22
0,30 0,08 0,30 0,010 0,025
1,10-
1,70
0,60
DIN EN 10028-2 P265GH+N 0,20 0,025 0,010 0,30 0,40
0,80-
1,40
0,08 0,30 0,012
Alges 0,020
Cu 0,30
Nb 0,020
Ti max. 0,03
V 0,02
GB713 Q345R 0,20 0,015
+N GB713 Q245R
1.0425
0,35
0,50-
1,00
0,025 0,015
+N
0,08 0,30 0,12
Alges. 0,020
Cu 0,30
Nb 0,020
Ti max. 0,03
V 0,02
+N 0,025 0,010 0,16 0,35 1.0345 DIN EN 10028-2 P235GH+N -20 -
0
0,60 -
1,20
400-520 25
24
31
360-480
24 27
410-530
22 27 -20
0,20
N
o
n
-
a
l
l
o
y

a
n
d

a
l
l
o
y

s
t
e
e
l
s

w
i
t
h

s
p
e
c
i
f
i
e
d

e
l
e
v
a
t
e
d

t
e
m
p
e
r
a
t
u
r
e

p
r
o
p
e
r
t
i
e
s
0,30
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
16 275
16-40 270
40-60 260
60-100 240 430-580
100-150 220 420-570
150-250 210 410-570
not known
16 300
16-60 290
60-100 270 440-590
100-150 255 430-580
6-100 310 520-680
100-150 300 510-670
100-150 255 430-590
150-250 245 420-570
6-100 310 520-680
100-150 300 510-670
16-40 - 470 -
40-63 - 610 -
63-100 - 820 -
5-10 510 650-950 6
10--16 420 600-900 7
16-40 320 550-850 8
40-63 300 520-770 9
63-100 255 470-740 9
16 275 20
16 - 40 265 19
40 - 60 255 18
60 - 100 245 17
100 - 150 235 16
>150 225 15
B
r
i
g
h
t

s
t
e
e
l

f
o
r

g
e
n
e
r
a
l

e
n
g
i
n
e
e
r
i
n
g

p
u
r
p
o
s
e
s
34 20
0,50-
0,80
+QT GB713 14Cr1MoR
0,05-
0,17
0,40-
0,65
0,020 0,010
1,15-
1,50
0,45-
0,65
0,45-
0,65
19 27 20 +QT 1.7335 DIN EN 10028-2 13CrMo4-5+QT
0,08-
0,18
0,35
0,40-
1,00
0,025 0,010
0,70-
1,15
0,40-
0,60
0,012 Cu 0,30
1.7335
0,08-
0,18
0,35
0,40-
1,00
DIN EN 10028-2 13CrMo4-5+NT
19 34 20 +NT GB713 14Cr1MoR
0,05-
0,17
0,50-
0,80
0,40-
0,65
0,40-
0,60
0,010 0,30
0,25-
0,35
0,30
0,025 0,010
450-600
19
31
27
20
0,70-
1,15
0,012 Cu 0,30
440-590
22 31 20 0,35 0,012 Cu 0,30 +N 1.5415 DIN EN 10028-2
0,40-
0,90
0,025 16Mo3+N
+NT
0,009 - - 0,045
+SH
(as rolled and
turned)
+ C
(cold drawn)
140-181 - - -
0,28 -
0,38
-
Q275 GB 700-88 490-630 -
0,045
0,35
0,50 -
0,80
0,05
E295GC DIN EN 10277-2 1.0533 St50-2KG Unkilled not permitted
0,045
0,12-
0,20
0,020 0,010
1,15-
1,50
19
- -
N
o
n
-
a
l
l
o
y

a
n
d

a
l
l
o
y

s
t
e
e
l
s

w
i
t
h

s
p
e
c
i
f
i
e
d

e
l
e
v
a
t
e
d

t
e
m
p
e
r
a
t
u
r
e

p
r
o
p
e
r
t
i
e
s
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
16-40 - -
40-63 - -
63-100 - -
5-10 565 750 - 1050 7
10--16 500 710 - 1030 8
Cr+Mo+Ni
max. 0,63
16-40 410 650 - 1000 9
40-63 360 630 - 900 11
63-100 310 580 - 850 12
16-40 - -
40-63 - -
63-100 - -
5-10 380 500-800 7
10--16 340 480-780 8
16-40 280 430-730 9
40-63 240 380-670 11
63-100 215 340-600 12
DC01 DIN EN 10130 1.0330 St 12 03 +LC 3 140 270 - 410 28 - - - - 0,12 - 0,60 0,045 0,045 - - - -
08F GB 699-88 25 175 295 35 60 - - 131
0,05 -
0,11
0,03
0,25 -
0,50
0,035 0,035 0,10 - 0,25 - Cu 0,25 Sameness must be checked in every case.
B
r
i
g
h
t

s
t
e
e
l

f
o
r

g
e
n
e
r
a
l

e
n
g
i
n
e
e
r
i
n
g

p
u
r
p
o
s
e
s
S
h
e
e
t
s
330-600
- - -
27
0,25 Cu 0,25
0,045
0,12 -
0,18
0,40
0,30 -
0,80
0,045
- - 98-178
16
580 - 820
0,045 0,045
0,17 -
0,37
0,50 -
0,80
45 GB 699-88
- 172 - 242
0,035
1.0503
-
0,40 0,40
0,50 -
0,80
- - -
-
143 - 0,25 15 GB 699-88 375 225 0,035
C15 DIN EN 10277-2
C45 DIN EN 10277-2
55
0,12 -
0,19
0,035
0,35 -
0,65
0,17 -
0,37
600 40 39 20 229
-
-
0,42 -
0,50
Normalized
1.0401
+ C
(cold drawn)
+SH
(as rolled
and turned)
C45
+SH
(as rolled and
turned)
355 0,25
0,42 -
0,50
Unkilled not permitted 0,40 0,10
Cu 0,25 Fully killed steel is permissible 0,035 0,25
C15
+ C
(cold drawn)
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
16 235
16-40 225
40-60 215
20
GB 8162-2008
GB 8163-2008
- 16 245 410-530 20 - - - - - - - -
GB8162-2008 Seamless tubes used for construction
GB8163-2008 Seamless tubes used for liquid
transmitting
Q235A GB 8162-2008 - 16 235 375-500 25 - - - 0,22 0,35 1,40 0,030 0,030 GB8162-2008 Seamless tubes used for construction
16 235
16-40 225
40-60 215
20
GB 8162-2008
GB 8163-2008
- 16 245 410-530 20 - - - - - - - - - - -
transmitting
Q235C GB 8162-2008 - 16 235 375-500 25 - 27 0 ? ? ? ? ? GB8162-2008 Seamless tubes used for construction
16 235
16-40 225
40-60 215
20
GB 8162-2008
GB 8163-2008
- 16 245 410-530 20 - - - - - - -
transmitting
12
12-20
20-40 345
40-50 335
50-65 325
65-80 315
80-100 305
Q345D
GB 8162-2008
GB 8163-2008
- 16 345 470 - 630 21 - 34 -20 - - - - -
transmitting
Q235C GB 8162-2008 15 245 390-530 20 - 27 0
0,17 -
0,24
0,17-
0,37
0,35-
0,65
0,035 0,035 - - - - GB8162-2008 Seamless tubes used for construction
P460NH DIN EN 10216-3 1.8935 - Normalized 12 460 560-730 19 - 40 -20 0,20 0,60
1,00-
1,70
0,025 0,02 0,30 0,10 0,80 0,020
Al gesamt.
min.0,020
Q460E
GB 8162-2008
GB 8163-2008
- 16 460 550 - 720 17 - 34 -20 - - - - -
transmitting
- - 0,04 0,04 P235TR2 DIN EN 10216-1 1.0255 QSt 37.0 Normalized 360 - 500 - - 25 - - -
100 -
140
0,17 -
N
o
n
-
a
l
l
o
y

s
t
e
e
l

f
o
r

t
u
b
e
s
360 - 500
- Nb0,009
- - - Nb0,009 0,04 25
450 - 590
-
0,30
0.90 -
1,70
E 235 +N DIN EN 10305-4 Normalized 340 - 480
355 490 - 650
490 - 630
235
P235TR1 DIN EN 10216-1 1.0254 St 37.0
P235GH DIN EN 10216-2 1.0345 St 35.8 Normalized 360 - 500 25
- -
100 -
140
22 -
-
100 -
140
- -
55
0,17 0,35 1,20 -
- 0,17 - - - 0,04
- - - -
0,025 0,02
-
P355N DIN EN 10216-3 1.0562
25
St 52.4 / StE 355
1.0308
-
20
145 -
185
0,20 0,50
0,17 Nb0,009 - 0,04 0,04 - -
0,50 0,02
Alges.
min.0,020
Cu max.0,30
Nb max.0,05
Ti max.0,040
V max.0,10
0,08
-
0,025 0,015 -
Normalized
Normalized
-
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
100 300 530 22 - 50 20
100 - 250 280 520 22 - 50 20
250 - 500 260 500 22 - 40 20
500 -
1000
250 490 22 - 40 20
20Mn2 GB 3077-88 15 590 785 10 40 47 20
max.
187
0,17 -
0,24
0,17 -
0,37
1,40 -
1,80
0,035 0,035 0,30 - 0,30 Cu max. 0,30 Z = Fully killed steel is permissible
600 265 470 15 30 39 20
600 - 900 255 450 14 30 39 20
16 590 800 - 950 13 40 35 20
16 - 40 490 700 - 850 15 45 40 20
40 - 100 440 650 - 800 16 50 40 20
100 310 600 18 - 35 20
100 - 250 290 570 18 - 30 20
250 - 500 270 540 18 - 25 20
500 -
1000
260 540 17 - 20 20
35SiMn GB/T3077-99 100 510 785 15 45 47 20 235-286
JB/T6396-2006 101 - 300 440 735 14 35 39 20 217-269
301 - 400 390 685 13 30 35 20 207-255
401 - 500 375 635 11 28 31 20 196-255
16 240 430 24 - - -
16 - 100 210 410 25 - - -
C22 DIN EN 10250-2 1.0402 C22N +N 100 210 410 25 - - - max. 156 Steel for forgings
20 GB 699-88 Normalized 25 245 410 25 55 - - max. 156
0,17 -
0,24
0,17 -
0,37
0,35 -
0,65
0,035 0,035 0,25 0,25 Cu 0,25 Fully killed steel is permissible
S
t
e
e
l
s

u
n
a
l
l
o
y
d

o
r

a
l
l
o
y
d
,

n
o
r
m
a
l
i
z
e
d

o
r

q
u
e
n
c
h
e
d

a
n
d

t
e
m
p
e
r
e
d

/

S
t
e
e
l

f
o
r
g
i
n
g
s
C22 DIN EN 10083-2 1.0402 C22N
DIN EN 10250-2
1.1170 DIN EN 10083-1 30 Mn 5
1.1170 30 Mn 5
+QT
+QT
Quenched and
tempered
0,035 0,035
Steel for forgings
0,32 -
0,40
1,10 -
1,40
0,035 0,40 0,10 0,40 -
Al min. 0,020
Cr+Mo+Ni
max. 0,63
1,30 -
1,65
0,25 -
0,32
0,035
28Mn6
28Mn6
1,10 -
1,40
+N Unkilled not permitted
0,40
0,035
0,60 -
0,80
1,00 -
1,30
1,00 -
1,50
0,16 -
0,22
0,40
0,045
Cr+Mo+Ni
max. 0,63
0,045 - 0,40 0,10 0,40
0,035 0,035
20Mn5 DIN EN 10250-2 1.1133 20 Mn 5
Al min. 0,020
Cr+Mo+Ni
max. 0,63
0,40 0,10 0,40 - Steel for forgings
0,17 -
0,24
max. 156
0,40
0,40 -
0,70
0,035
20SiMn GB 3077-99
+N
0,17 -
0,23
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
16 300 550 18
16 - 100 270 520 19
100 - 250 245 500 19
16 430 630 - 780 17 40
16 - 40 380 600 - 750 19 45
40 - 100 320 550 - 700 20 50
16 430 630 - 780 17 40
16 - 40 380 600 - 750 19 45
40 - 100 320 550 - 700 20 50
100 270 520 30
100 - 250 245 500 25
250 - 500 220 480 20
CK35 500 - 1000 210 470 18 17
500 - 1000 245 490 - 610 20 -
70 320 550 20 35
70 - 160 290 490 22 31
160 - 330 270 470 21 25
35 GB 699-88
Normalized or
quenched and
tempered
25 315 530 20 45 55 20 max. 156
0,32 -
0,40
0,17 -
0,37
0,50 -
0,80
16 340 620 14
16 - 100 305 580 16
100 - 250 275 560 16
16 490 700 - 850 14 35
16 - 40 430 650 - 800 16 40
40 - 100 370 630 - 780 17 45
16 490 700 - 850 14 35
16 - 40 430 650 - 800 16 40
40 - 100 370 630 - 780 17 45
100 305 580 -
100 - 250 275 560 18
250 - 500 240 540 15
CK45 500 - 1000 230 530 15 12
500 - 1000 295 590 - 720 15 -
70 370 630 17 25
70 - 160 340 590 18 22
160 - 330 320 540 17
20
45 EZB 1183-93
Quenched and
tempered
500 700 - 850 14 30 31 20 -
45 GB 699-88
Normalized or
quenched and
tempered
25 355 600 16 40 39 20 max. 229
45H GB 5216-85 Structural steels with defined hardenability scatterband
S
t
e
e
l
s

u
n
a
l
l
o
y
d

o
r

a
l
l
o
y
d
,

n
o
r
m
a
l
i
z
e
d

o
r

q
u
e
n
c
h
e
d

a
n
d

t
e
m
p
e
r
e
d

/

S
t
e
e
l

f
o
r
g
i
n
g
s
1.0501 C35N
C35E +QT DIN EN 10083-1
35
35
C35 +N DIN EN 10083-2
+N
1.1181
0,40 -
Cr+Mo+Ni
max. 0,63
Not known
0,035
0,40 0,10
C35 +QT DIN EN 10083-2 1.0501
-
C35V
- - +N
+QT
0,40 0,10 0,40 - 0,40
0,40
20
- 0,035 0,40
0,50 -
0,80
0,035 Ck35V +QT
+QT 20
0,045
0,035
19
- -
0,32 -
0,39
0,50 -
0,80
0,035
Unkilled not permitted 20
+QT 25 20
0,035
0,32 -
0,39
0,40
0,50 -
0,80
0,035
0,045
0,045
+N
Cr+Mo+Ni
max. 0,63
Cr+Mo+Ni
max. 0,63
Unkilled not permitted 0,40 -
max. 207
16
-
Cr+Mo+Ni
max. 0,63
0,50 -
0,80
Steel for forgings
-
0,40 0,10
0,40
Cr+Mo+Ni
max. 0,63
0,10 0,40
20
Unkilled not permitted 0,045
0,32 -
0,39
0,40
0,50 -
0,80
-
0,40 0,40
Cr+Mo+Ni
max. 0,63
0,10
Cr+Mo+Ni
max. 0,63
C45E +QT DIN EN 10083-1 1.1191 Ck45V +QT 25 20
0,40
0,10
0,42 -
0,50
- max. 207 0,045 0,40
0,42 -
0,50
0,40
0,40
0,50 -
0,80
0,045 0,045 0,10
C45N +N - -
0,50 -
0,80
C45V
0,42 -
0,50
0,40
0,50 -
0,80
0,40 -
0,25 Cu 0,25
Steel for forgings 0,40
Cr+Mo+Ni
max. 0,63
0,035 0,25
0,035
0,045
0,42 -
0,50
0,17 -
0,37
0,50 -
0,80
DIN EN 10083-2 1.0503
C35E
DIN EN 10250-2
SEW 550
1.1191
DIN EN 10083-2 1.0503
+QT
0,42 -
0,50
20
20
- 0,035 0,40 0,10 0,40
0,32 -
0,39
max. 156
C45 +N
C45 +QT
C45E
DIN EN 10250-2
SEW 550
1.1191
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
16 550 800 - 950 12 30
16 - 40 490 750 - 900 14 35
40 - 100 420 700 - 850 15 40
16 550 630 - 780 12 30
16 - 40 490 600 - 750 14 35
40 - 100 420 550 - 700 15 40
55 GB 699-88
Normalized or
quenched and
tempered
25 375 630 14 40 31 20 max. 241
0,52 -
0,60
0,17 -
0,37
0,50 -
0,80
16 340 620 14
16 - 100 305 580 16
100 - 250 275 560 16
100 340 670
100 - 250 310 650
250 - 500 275 630
500 - 1000 260 620 10
500 - 1000 345 680 - 830 12
70 450 750 14
70 - 160 390 690 15
160 - 330 350 670 14
60 GB 699-88 Normalized 25 400 675 12 35 - - max. 255
0,57 -
0,65
0,17 -
0,37
0,50 -
0,80
16 700 900 - 1100 12 50 45 20
16 - 40 600 800 - 950 14 55 50 20
40 - 100 450 700 - 850 15 60 50 20
100 - 160 400 650 - 800 16 60 45 20
70 450 700 15 50 20
70 - 160 400 650 17 45 20
160 - 330 380 600 18 38 20
30CrMo GB 3077-88 25 785 930 12 50 63 20 229
0,26 -
0,34
0,17 -
0,37
0,40 -
0,70
0,035 0,035
0,80 -
1,10
0,15 -
0,25
17-40 590 780-930 14 55 55* 20 229-286 * DVM Specimen, no KV
41-100 460 690-830 15 60 55* 20 207-255
101-160 410 640-780 16 60 48* 20 196-255
16 800 1000 - 1200 11 45 35 20
16 - 40 650 900 - 1100 12 50 40 20
40 - 100 550 800 - 950 14 55 45 20
100 - 160 500 750 - 900 15 55 45 20
160 - 250 450 700 - 850 15 60 45 20
70 550 800 14 45 20
70 - 160 450 700 15 40 20
160 - 330 410 650 16 33 20
25 835 980 12 45 63 20 229
100 510 785 15 45 47 20 235-286
101-300 490 685 15 45 39 20 207-255
301-400 440 635 15 35 31 20 196-255
401-500 390 590 12 30 23 20 176-241
0,90-
1,20
0,15-
0,30
C55V +QT - -
0,035 0,40
0,40
0,60 -
0,90
Unkilled not permitted 0,045 0,045 0,40
0,50-
0,80
0,40 -
0,70
0,035
0,22-
0,29
0,035
0,035 0,035
- Ck55V
35CrMo
0,17-
0,37
0,17 -
0,37
0,40
0,40
0,60 -
0,90
0,80 -
1,10
Unkilled not permitted 0,40 0,10 0,40 - 0,035 0,035
Unkilled not permitted 0,10 0,40 -
Cr+Mo+Ni
max. 0,63
0,60 -
0,90
0,035 +QT -
Cr+Mo+Ni
max. 0,63
0,10 0,40 -
Cr+Mo+Ni
max. 0,63
- +QT 25CrMo4 DIN EN 10250-3
- -
Steel for forgings
0,035
0,90 -
1,20
0,15 -
0,30
0,40
34CrMo4 DIN EN 10250-3 1.7220 34CrMo4V Steel for forgings
0,15 -
0,30
- -
Steel for forgings
+QT
- -
max. 207
0,10 0,40
Cr+Mo+Ni
max. 0,63
0,60 -
0,90
0,035
1.7218
25CrMo4 DIN EN 10083-1
0,60 -
0,90
0,035
0,22 -
0,29
+N - - -
0,40 0,035 0,40 -
25CrMo4V
25CrMo4V
CK45 1.1221
0,30 -
0,37
0,32 -
0,40
0,035 0,40
0,60 -
0,90
0,035
34CrMo4V +QT
0,15 -
0,25
+QT -
GB 3077-88
JB/T6396-2006
max. 207
0,57 -
0,65
0,57 -
0,65
+QT
1.0601
-
0,90 -
1,20
DIN EN 10083-2
DIN EN 10083-1 1.1203
C60E
+N
DIN EN 10250-2
SEW 550
0,57 -
0,65
0,57 -
0,65
C60N
DIN EN 10083-2 1.0535
1.7218
DIN EN 10083-1
JB/T 6396-2006
16
S
t
e
e
l
s

u
n
a
l
l
o
y
d

o
r

a
l
l
o
y
d
,

n
o
r
m
a
l
i
z
e
d

o
r

q
u
e
n
c
h
e
d

a
n
d

t
e
m
p
e
r
e
d

/

S
t
e
e
l

f
o
r
g
i
n
g
s
S
t
e
e
l
s

u
n
a
l
l
o
y
d

o
r

a
l
l
o
y
d
,

n
o
r
m
a
l
i
z
e
d

o
r

q
u
e
n
c
h
e
d

a
n
d

t
e
m
p
e
r
e
d

/

S
t
e
e
l

f
o
r
g
i
n
g
s
25CrMo
C60 +N
C55E +QT
C55 +QT
34CrMo4 1.7220
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
16 900 1100 - 1300 10 40 30 20
16 - 40 750 1000 - 1200 11 45
40 - 100 650 900 - 1100 12 50
100 - 160 550 800 - 950 13 50
160 - 250 500 750 - 900 14 55
160 550 800 14 45 20
160 - 330 450 700 15 40 20
330 - 500 410 650 16 33 20
500 - 750 390 590 - 740 16 - -
25 835 980 12 45 63 20 229
0,32 -
0,40
0,17 -
0,37
0,40 -
0,70 0,035 0,035
0,80 -
1,10
0,15 -
0,25 Fully killed steel is permissible
100 650 900-1100 12 50 35 20 269-321
101-160 550 800-950 13 50 35 20 241-302
161-250 500 750-900 14 50 35 20 225-269
251-500 460 690-840 15 - - 207-255
501-750 390 590-740 16 - - 176-241
16 900 1100 - 1300 9 40 30 20
16 - 40 780 1000 - 1200 10 45
40 - 100 700 900 - 1100 12 50
100 - 160 650 850 - 1000 13 50
160 - 250 550 800 - 950 13 55
160 550 800 13 25 20
160 - 330 540 750 14 20 20
330 - 500 490 700 15 15 20
500 - 750 490 690 - 840 15 - -
100 700 900 12 50 35 20
0,46 -
0,54
0,17 -
0,37
0,50 -
0,80
0,035 0,035
0,90 -
1,20
0,15 -
0,25
100 700 900-1100 12 50 35 20 269-321

EZB 1184-93
JB/T 6396-2006
101-160 650 800-1000 13 50 35 20 241-302
161-250 550 800-950 14 50 35 20 225-269
251-500 540 740-890 15 - - 207-255
501-750 490 690-840 16 - - 176-241
0,40
0,60 -
0,90
50CrMo
0,46-
0,54
0,17-
0,37
0,50-
0,80
0,035
0,90 -
1,20
0,15 -
0,30
- -
50CrMo4

GB 3077-88
JB/T6396-2006
0,38-
0,45
0,17-
0,37
0,50-
0,80
50CrMo4V
Steel for forgings
0,035 0,035
35
DIN EN 10083-1 1.7228 50CrMo4V
42CrMo4V
42CrMo4V DIN EN 10083-1
30 20
0,90 -
1,20
0,15 -
0,30
- -
Steel for forgings
0,40
0,50 -
0,80
0,035 0,035
0,46 -
0,54
0,38 -
0,45
+QT
+QT 1.7225
+QT - 1.7225
0,035 0,035 0,90-
1,20
0,15-
0,30
20
50CrMo4
DIN EN 10250-3
SEW 550
1.7228
DIN EN 10250-3
SEW 550
0,035 0,90-
1,20
0,15-
0,30
42CrMo
+QT -
42CrMo4
S
t
e
e
l
s

u
n
a
l
l
o
y
d

o
r

a
l
l
o
y
d
,

n
o
r
m
a
l
i
z
e
d

o
r

q
u
e
n
c
h
e
d

a
n
d

t
e
m
p
e
r
e
d

/

S
t
e
e
l

f
o
r
g
i
n
g
s
42CrMo4
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
16 1000 1200 - 1400 9 40 35 20
16 - 40 900 1100 - 1300 10 45 45 20
40 - 100 800 1000 - 1200 11 50 45 20
100 - 160 700 900 - 1100 12 55 45 20
160 - 250 600 800 - 950 13 55 45 20
160 600 800 13 45 20
160 - 330 540 750 14 45 20
330 - 500 490 700 15 40 20
500 - 1000 490 690 - 840 15 - -
100 800 1000-1200 11 50 45 20 302-341 Fully killed steel is permissible
101-160 700 900-1100 12 55 45 20 269-321
161-250 600 800-950 13 55 45 20 241-302
251-500 540 740-890 14 - - 225-269
501-1000 490 690-840 15 - - 207-255
16 1050 1250 - 1450 9 40 30 20
16 - 40 1050 1250 - 1450 9 40 30 20
40 - 100 900 1100 - 1300 10 45 35 20
100 - 160 800 1000 - 1200 11 50 45 20
160 - 250 700 900 - 1100 12 50 45 20
160 700 900 45 20
160 - 330 630 850 45 20
330 - 500 590 800 40 20
500 - 1000 590 780 - 930 - -
30Cr2Ni2Mo EZB 1184-93 100 900 1100 10 45 40 20
0,26 -
0,34
0,17 -
0,37
0,30 -
0,60
0,035 0,035
1,80 -
2,20
0,30 -
0,50
1,80 -
2,20
30Cr2Ni2Mo JB/T 6396-2006 100 900 1100-1300 10 45 35 20 325-369
101-160 800 1000-1200 11 50 45 20 302-341
161-250 700 900-1100 12 50 45 20 269-321
251-500 635 830-980 12 - - 250-302
501-1000 590 780-930 12 - - 229-286
70 980 1100 10 - 28 20
70 - 160 820 1000 12 - 48 20
160 - 330 780 950 12 -
48 20
1000 785 930 - 1130 12 - -
1000 - 1500 735 880 - 1080 13 - -
1500 - 2000 685 830 - 980 14 - -
No conversion
160 700 900 12 - 35 20
160 - 330 590 800 14 - 35 20
No conversion
0,30 -
0,38
34Cr2Ni2Mo
0,17 -
0,37
0,40 -
0,70
0,15 -
0,30
1,40-
1,70
0,035 1,80 -
2,20
0,30 -
0,50
1,80 -
2,20
0,26 -
0,34
0,17 -
0,37
0,30 -
0,60
0,035
1,30 -
1,70
- 0,40
0,50 -
0,80
0,40
30CrNiMo8
DIN EN 10250-3
SEW 550
1.6580 30CrNiMo8 +QT - Steel for forgings
0,30 -
0,50
1,80 -
2,20
-
30CrNiMo8 V
34CrNiMo6
DIN EN 10250-3
SEW 550
1.6582 34CrNiMo6
30CrNiMo8 DIN EN 10083-1 1.6580
JB/T 6396-2006
Steel for forgings
1,30 -
1,70
0,15 -
0,30
34CrNiMo6 V +QT
-
30CrMoV9 DIN EN 10250-3 1.7707
0,40 -
0,70
0,035
0,15 -
0,25
0,60
0,035 Steel for forgings 33NiCrMoV14-5
DIN EN 10250-3
SEW 550
1.6956 33 NiCrMo14 5 +QT
0,30 -
0,60
V 0,08 - 0,25
0,15 -
0,40
-
0,28 -
0,38
0,40
30 CrMoV 9 +QT V 0,10 - 0,20 Steel for forgings
12
0,26 -
0,34
0,40
0,035
1,00 -
1,70
DIN EN 10083-1 1.6582 34CrNiMo6
2,90 -
3,80
0,30 -
0,38
+QT -
0,035 0,035 1,40 -
1,70
0,035
2,30 -
2,70
0,035 0,035
1,80 -
2,20
0,035 0,035
0,30 -
0,60
+QT
0,26 -
0,34
S
t
e
e
l
s

u
n
a
l
l
o
y
d

o
r

a
l
l
o
y
d
,

n
o
r
m
a
l
i
z
e
d

o
r

q
u
e
n
c
h
e
d

a
n
d

t
e
m
p
e
r
e
d

/

S
t
e
e
l

f
o
r
g
i
n
g
s
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
+A - - - - - - - max. 223
+H
- - - - - - -
HRC
min. 60
Cr2 GB 1299-85 Not known Not Known
GCr15 YB/T 1 ?? Not known
0,95 -
1,05
0,15 -
0,35
0,25 -
0,45
0,025 0,025
1,40 -
1,65
+A max. 229
+H
HRC
min. 58
6 Cr W2 Si GB 1299-85 Not known Not known
100 39 20
100 - 250 31 20
250 - 330 27 20
+QT1 160 600 800 - 950 14 40 27 20
+QT2 160 600 800 - 950 14 40 27 20
1Cr11MoV GB 1221-92 490 685 16 55 - -
0,11 -
0,18
10,00
-
11,50
0,50 -
0,70
0,6 V 0,25 - 0,40
Material is only similar,
Notch impact energy not guaranteed,
+A - - max. 760 - - - - max. 230
+QT700 160 500 700 - 850 13 - 25 20 -
+QT800 160 600 800 - 950 12 - 20 20 -
+A - - max. 760 - - - - max. 230
+QT700 160 500 700 - 850 13 - 25 20 -
+QT800 160 600 800 - 950 12 - 20 20 -
2Cr13
GB 1220-92
GB 1221-92
GB 8732-88
+QT 75 440 635 20 50 63 20 192
0,16 -
0,25
1,00 1,00 0,035 0,03
12,00
-
14,00
- - Material is only similar (Mechanical properties!)
3Cr13
GB 1220-92
GB 1221-92
GB 8732-88
+QT 75 540 735 12 40 24 20 217
0,26 -
0,40
1,00 1,00 0,035 0,03
12,00
-
14,00
- - Material is only similar (C-content!)
+A 800 245
DIN EN 10088-3
+A 207
GB 1220-92 (+QT)
OFH:
HRC
min. 50
0,36 -
0,45
0,60 0,80 0,035 0,03
12,0 -
14,0
Material is only similar (Mechanical properties!)
T
o
o
l
s

s
t
e
e
l
s
+QT800 1,00
4Cr13
Semi-finished products 0,04 0,03
12,5 -
14,5
- -
OFH:
HRC
min. 55
0,43 -
0,50
1,00
X46Cr13 1.4034
Not known
850-1000 10 - 12 20 160 650
0,03 0,03
1,35 -
1,65
- 102Cr6
DIN EN ISO
4957
1.2067 100 Cr 6
0,95 -
1,10
0,15 -
0,35
X22CrMoV12-1
X20CrMoV11-1 DIN EN 10222-2 1.4922
DIN EN 10269 1.4923
+QT
0,17 -
0,23
V 0,10 - 0,20
W 1,70 - 2,20
V 0,20 - 0,35 0,025 0,015
10,00
-
12,50
0,80 -
1,20
0,30 -
0,80
-
0,30 -
0,80
- V 0,25 - 0,35
60WCrV8
DIN EN ISO
4957
1.2550
11,00
-
12,50
60 WCrV 7
0,55 -
0,65
0,70 -
1,00
0,15 -
0,45
0,03 0,03 -
DIN EN 10088
0,5
0,18 -
0,24
X 22CrMoV 121
-
0,30 -
1,00
500 700 - 850 16 -
0,80 -
1,20
0,015
-
0,40 -
0,90
Steel for forgings
0,90 -
1,20
-
X20Cr13
Steel for forgings
0,16 -
0,25
1,00 1,50 0,04 0,03
12,00
-
14,00
0,025
X20Cr13 DIN EN 10250-4 1.4021 X 20 Cr 13
-
1.4021 X 20 Cr 13
-
0,40
-
0,25 -
0,45
- -
H
e
a
t
-
r
e
s
i
s
t
i
n
g

s
t
e
e
l
s
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
+A - - max. 1000 - - - - max. 295
+QT800 160 600 800 - 900 10 - 20 20 -
+QT900 160 700 900 - 1050 10 - 15 20 -
+A - - max. 1000 - - - - max. 295
+QT800 160 600 800 - 900 10 - 20 20 -
+QT900 160 700 900 - 1050 10 - 15 20 -
1Cr17Ni2
GB 1220-92
GB 1221-92
GB 3280-92
Material is only similar (Yield-strength is not
guaranteed)
GB/T 4231-93
GB/T 4240-93
GB 4356-84
+A - - max. 1100 - - - - max. 320
+QT760 450 550 760 - 960 16 - 90 20 -
+QT900 450 700 900 - 1100 16 - 80 20 -
X4CrNi18-10 DIN EN 10250-4 1.4301 X5 CrNi 18 9 250 190 500 - 700 35 - 100 20 Steel for forgings
0Cr18Ni9 GB 1220-92
solution
anealing
180 205 520 40 60 - - max. 187 0,07 1,00 2,00 0,035 0,03
17,00
-
-
8,00 -
11,00
-
X6CrNiTi18-10 DIN EN 10250-4 1.4541 X10 CrNiTi 18 9 250 190 500 - 700 30 - 100 20 Steel for forgings
X6CrNiTi18-10
DIN EN 10216-5
DIN EN 10217-7
1.4541 50 200 500 - 730 35 - 100 20 130 - 180 Pipes and tubes
0Cr18Ni10Ti
GB 1220-92
GB 1221-92
GB 3280-92
GB4237-92
GB4238-92
GB 4356-84
GB 12771-91
GB 13296-91
GB/T 14975-94
GB/T 14976-94
solution
annealing
180 205 520 40 60 - - max. 187 0,08 1,00 2,00 0,035 0,03
17,00
-
19,00
-
8,00 -
11,00
-
Ti = 5xC,
max. 0,80
-
1,50 -
2,50
- 10 - 39
250 190
0,80 0,035 0,03
16,00
-
18,00
0,045 0,07
35 - 100 20
100
250
0,11
500 - 700 30 -
0,015
17,00
-
19,00
-
1,50 -
250
0,12 -
0,22
1,00 1,50 0,04 - -
X17CrNi16-2 DIN EN 10250-4 1.4057 X 17 CrNi 162
Steel for forgings
0,03
15,00
-
17,00
X17CrNi16-2 DIN EN 10088 1.4057 X 17 CrNi 162
No conversion
X4CrNi18-10 DIN EN 10088 1.4301
+QT 75 - 20 -
0,11 -
0,17
0,80 1080
solution
annealing
0,08 1,00 2,00 0,045
190 500 - 700
0,015
17,00
-
19,50
-
8,00 -
10,50
1,00 2,00
solution
annealing
X5 CrNi 18 9
X6CrNiTi18-10 DIN EN 10088 1.4541 X10 CrNiTi 18 9
Ti = 5xC,
max. 0,70
-
9,00 -
12,00
0,11
20
Steel for forgings 0,06 0,70 1,50
4,00 -
6,00
15,00
-
17,00
0,80 -
1,50
X4CrNiMo16-5-1 DIN EN 10250-4 1.4418 - 0,045 0,03 0,02 -
S
t
a
i
n
l
e
s
s

s
t
e
e
l
s
SN359-1 : 2012-06
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d

s
t r
e
n
g
t h
R
e
T
e
n
s
i l e

s
t r
e
n
g
t h
R
m
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t . A
5
R
e
d
u
c
t i o
n
o
f
a
r
e
a
Z
N
o
t c
h
i m
p
a
c
t
e
n
e
r
g
y
K
V
T
e
s
t -
t e
m
p
e
r
a
t u
r
e

H
a
r
d
n
e
s
s

a
f t e
r
h
e
a
t
t r
e
a
t m
e
n
t
Material
No.
Former
designation
Heat
treatment
J C
Notice
00Cr17Ni14Mo2
GB 1220-92
GB 1221-92
177 480 40 60 - - max. 187
0,03 1,00 2,00 0,035 0,03
16,00
-
2,00 -
3,00
12,00 -
15,00 -
0Cr17Ni12Mo2
GB 1220-92
GB 1221-92
180 205 520 40 60 - - max. 187 0,08 1,00 2,00 0,035 0,03
16,00
-
2,00 -
3,00
10,00 -
14,00
-
0Cr18Ni12Mo2Ti
GB 1220-92
GB4237-92
GB 13296-91
GB/T 14975-94
GB/T 14976-94
solution
annealing
180 205 520 40 60 - - max. 187 0,08 1,00 2,00 0,035 0,03
16,00
-
18,50
2,00 -
3,00
10,00 -
14,00
-
- 100 20
2,00 -
2,50
10,00 -
13,00
0,11
500 - 700
20
X5CrNiMo17-12-2 DIN EN 10250-4 1.4401 X5 CrNiMo 17 12 2
250 200 500 - 700 30 - 100
2,00
solution
annealing
250 200
0,07 1,00
Steel for forgings
100
X6CrNiMoTi17-12-2 DIN EN 10088 1.4571
Ti = 5xC,
max. 0,70
2,00 0,045 0,015
16,50
-
18,50
Pipes and tubes
Steel for forgings
2,00 -
2,50
10,00 -
13,00
1,00
250 200
X5CrNiMo17-12-2 DIN EN 10088 1.4401 X5 CrNiMo 17 12 2
30
max. 215
500 - 700 20
-
30 - 100
30 20
0,11
250
solution
annealing
X6CrNiMoTi17-12-2
DIN EN 10216-5
DIN EN 10217-7
1.4571 X10 CrNiMoTi 18 10
solution
annealing
X10 CrNiMoTi 18 10 max. 215
210 500 - 730 35 -
200 500 - 700 X6CrNiMoTi17-12-2 DIN EN 10250-4 1.4571 X10 CrNiMoTi 18 10
50
2,00 -
2,50
0,045 0,015
16,50
-
18,50
- 100 20 130 - 180 2,00 0,045 0,015
16,50
-
18,50
0,08 1,00
10,50 -
13,50
0,07
S
t
a
i
n
l
e
s
s

s
t
e
e
l
s
SN359-1 : 2012-06
Anhang/Appendix B2 (normativ) - Comparison of german and chinese material properties, cast steels
Notice
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d
p
o
i n
t ,
p
r
o
o
f s
t r
e
s
s
T
e
n
s
i l e

s
t r
e
n
g
t h
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t u
r
e
R
e
d
u
c
t i o
n
o
f
a
r
e
a
N
o
t c
h

t o
u
g
h
n
e
s
s

(
2
0
C
)
T
e
s
t -
t e
m
p
e
r
a
t u
r
e
F
a
t i g
u
e

s
t r
e
n
g
t h
H
a
r
d
n
e
s
s

a
f t e
r

a
n
n
e
a
l i n
g
mm MPa MPa % % J C Mpa HBW C Si Mn P S Cr Mo Ni N other
200 380 - 530 25 - 35 20 - -
ZG 200-400
GB 11352-89
EZB 1161-93
- 100 200 400 25 40 30 20 - -
0,12 -
0,20
0,45 0,80
EZB-Standards are work-standards from CHINA
NATIONAL ERZHONG GROUP
30 300 600 - 750 15 - 27 20 - -
30 - 100 300 520 - 670 18 - 31 20 - -
ZGD 345-570 GB/T 14408-93 345 570 - - - - - - - - - 0,04 0,04 - - - - -
ZGD 410 - 620 GB/T 14408-93 410 620 - - - - - - - - - 0,04 0,04 - - - - -
27 -30
50 20
27 -30
60 20
+N 295 510 14 - 30 (KCU) max. 156
+QT 300 500 - 650 24 - 45 20 150 - 190
30 260 520 18 25 27 20 - 150 - 200
30 - 100 260 520 18 25 22 20 - 150 - 200
DIN 1681
(invalid)
ZG 270-500 GB 11352-89
ZG 290-510 GB/T 14408-93 100 290 510 -
310 570 100 15
+QT-steel is permisible,
GS-52
GS-52N
normalised
100 270
0,30 0,50 0,60 0,90 0,04 0,35
0,40 0,50
Cu max.
0,30
15 20 - -
0,80
480 - 620 -
0,02
-
22 20 - -
0,025 0,025
0,04
V max.
0,05, Cu
max. 0,30
0,30 - 25
0,02 0,30
0,04 0,35 0,20
500 - 650
0,60 -
0,80
1,00 -
1,30
0,035
22
0,035
0,28 -
0,35
0,30 -
0,50
0,60 -
0,80
0,12 -
0,22
500 0,90
0,30
0,4
- -
0,12
- 270 480 -
0,18 0,60 1,20 0,03
100 230 450 22 25 20 -
0,12 0,40
Cu max.
0,30
C content max. 0.30% must be limited to max. 0.23%!
EZB-Standards are work-standard from CHINA
NATIONAL ERZHONG GROUP.
- - - -
Mechanical properties
min. or range
GS-38N normalised 100
- - GS-45N
G20Mn5
ZG 340-640
GS 240 normalised
ZG 230-450
GE 300
DIN EN 10293
DIN EN 10293
GB/T 14408-93
DIN EN 10293
GB 11352-89
GB 11352-89
EZB 1161-93
ZGD 270-480
1.0449
1.0445
32
0,03 0,025 0,30
max. or range %
0,23 0,60 1,20
Heat-
treatment
-
GS 200
Chemical composition
0,025 0,30 0,12 0,40
Cu max.
0,30
Chemical composition must be agreed between the
manufacturer and purchaser
100 240 450 - 600 22 - 31 20
- -
-
0,23 -
0,30
0,20 -
0,45
0,50 -
0,80
0,04 0,04 - - -
20 - - 570 15
-
21
- - -
30 300 20 -
0,17 -
0,23
0,60
1,00 -
1,60
15 0,90
- 100 300
310
18 -
- -
0,50 -
0,80
10 20 - 100 340 640 10
1.0558 GS-60N normalised
100 0,50 0,60
- -
C content 0.50% to 0,60% , only limited weldability.
-
-
- -
0,53 -
0,60
0,20 -
0,45
- - - - 0,03 - 0,035
18
- - - -
C content must be limited, otherwise only limited
weldability.
0,04 0,04 - -
-
V max.
0,05, Cu
max. 0,30
0,04
- -
0,20 21
- - - - -
Material
Former
designation
DIN EN 10293 1.6220 GS-20Mn5
+QT
+N
G
e
n
e
r
a
l

p
u
r
p
o
s
e

c
a
s
t

s
t
e
e
l
Group Material designation Standard No.
1.0552
ZG 310-570 GB 11352-89
ZG 310-570 GB 11352-89
ZG 20Mn JB/T 6402-92
GS-52
SN359-1 : 2012-06
Notice
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d
p
o
i n
t ,
p
r
o
o
f s
t r
e
s
s
T
e
n
s
i l e

s
t r
e
n
g
t h
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t u
r
e
R
e
d
u
c
t i o
n
o
f
a
r
e
a
N
o
t c
h

t o
u
g
h
n
e
s
s

(
2
0
C
)
T
e
s
t -
t e
m
p
e
r
a
t u
r
e
F
a
t i g
u
e

s
t r
e
n
g
t h
H
a
r
d
n
e
s
s

a
f t e
r

a
n
n
e
a
l i n
g
min. or range max. or range %
Heat-
treatment
Chemical composition Material
Former
designation
+N 250 260 520 - 670 18 - 27 20 - -
+QT1 100 450 600 - 750 14 - 35 20 - -
+QT2 50 550 700 - 850 10 - 31 20 - -
+N - 345 570 12 20 24 - - - 0,30 0,60 1,00 0,035 0,035 - - - - -
+QT - 415 640 12 25 27 - - - 0,40 0,80 1,40 - - - - - - - No comparison for QT2 available.
100 450 600 - 750 16 - 40 20 - -
100 - 250 300 550 - 700 14 - 27 20 - -
QT2 100 550 700 - 850 10 - 18 20 - -
+N 392 588 12 20 191
+QT 539 686 12 25 240
100 600 800 - 950 12 - 31 20 - -
100 - 150 550 700 - 850 10 - 27 20 - -
150 - 250 350 650 - 800 10 - 16 20 - -
+QT2 100 700 850 - 1000 10 - 27 20 - -
G42CrMo4 SEW 835 1.7231 GS-42CrMo4 +QT 150 470 680 12 - - - - -
0,38 -
0,45
0,60
0,60 -
1,00
0,02 0,015
0,80 -
1,20
0,20 -
0,30
- - - Flame and induction hardening steel castings
ZG 42Cr1Mo
JB/T 6402-92
EZB 1162-92
+QT 490 690 - 830 11 30 - - 200 - 250
0,38 -
0,45
0,30 -
0,60
0,60 -
1,00
0,025 0,025
0,80 -
1,20
0,20 -
0,30
- - -
comparison for Flame-and induction hardening steel
castings
150 700 950 - 1000 12 - 32 20 - 240 - 290
150 - 250 650 800 - 950 12 - - - - 220 - 270
250 - 400 650 800 - 950 10 - - - - 220 - 270
150 550 800 - 950
150 - 250 500 750 - 900
100 700 850 - 1000 - 45 20
100 - 150 650 800 - 950 35 20
150 - 250 650 800 - 950 30 20
+QT2 100 800 900 - 1050 10 - 35 20
150 700 950 - 1000 12 - 32 20 - 240 - 290
150 - 250 650 800 - 950 12 - - - - 220 - 270
250 - 400 650 800 - 950 10 - - - - 220 - 270
20
GS-34CrNiMo6V
Q
u
e
n
c
h
e
d

a
n
d

t
e
m
p
e
r
e
d

s
t
e
e
l

c
a
s
t
i
n
g
s
1,40 -
1,70
0,15 -
0,35
1,40 -
1,70
- -
For welded parts C-content must be < 0,30%,
+QT-steel is permisible for comparison only,
0,30 -
0,37
0,30 -
0,50
0,50 -
0,80
0,035 -
0,02
0,80 -
1,20
0,15 -
0,30
0,4 -
Cu max.
0,30
comparison for QT1 and QT2!
1.7221 GS-25CrMo4V
QT1
0,22 -
0,29
0,60
0,50 -
0,80
0,025
Cu max.
0,30
1.7231 GS-42CrMo4V
0,38 -
0,45
0,60
0,60 -
1,00
0,02
0,80 -
1,20
-
0,60 -
1,00
0,035
G26CrMo4 DIN 10293
G42CrMo4 DIN 10293
DIN EN 10293
ZG 34Cr2Ni2Mo JB/T 6402-92
ZG 35Cr1Mo
JB/T 6402-92
EZB 1162-92
0,025
0,035
+QT1
12
12
0,035
0,02
1,40 -
1,70
0,15 -
0,35
0,025
ZG 34Cr2Ni2Mo JB/T 6402-92
G35CrNiMo6-6
+QT1
+N
1.6579
- 31
0,32 -
0,38
0,6
0,60 -
1,00
0,035 +QT
+QT
0,30 -
0,37
0,30 -
0,60
Cu max.
0,30
1,40 -
1,70
G28Mn6 DIN EN 10293 1.1165 GS-30Mn5V 0,60
1,20 -
1,80
0,035
comparison for QT1 and QT2!
1,40 -
1,70
0,15 -
0,35
0,30 -
0,37
0,30 -
0,60
0,60 -
1,00
0,035
0,12 0,40
Cu max.
0,30
0,30
1,40 -
1,70
-
0,15 -
0,30
0,4
0,80 -
1,20
0,20 -
0,30
0,03
0,25 -
0,32
ZG 35Mn JB/T 6402
SN359-1 : 2012-06
Notice
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d
p
o
i n
t ,
p
r
o
o
f s
t r
e
s
s
T
e
n
s
i l e

s
t r
e
n
g
t h
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t u
r
e
R
e
d
u
c
t i o
n
o
f
a
r
e
a
N
o
t c
h

t o
u
g
h
n
e
s
s

(
2
0
C
)
T
e
s
t -
t e
m
p
e
r
a
t u
r
e
F
a
t i g
u
e

s
t r
e
n
g
t h
H
a
r
d
n
e
s
s

a
f t e
r

a
n
n
e
a
l i n
g
Heat-
treatment
Former
designation
150 380 650 - 800
150 - 250 330 - -
250 - 400 300
50 600 750 - 850 14 - 35 20 - -
50 - 100 540 700 - 850 12 - 30 20 - -
100 - 150 480 620 - 770 10 - 27 20 - -
50 700 850 - 1000 10 - 27 20 - -
50 - 100 650 830 - 980 10 - 27 20 - -
+N 392 588 12 20 191
+QT 539 686 12 25 240
ZG20SiMn
JB/T 4297-86
EZB 1162-92
+N 100 300 500 - 650 24 30 45 20 - - 0,23 0,6
1,00 -
1,50
0,025 0,025 0,30 0,15 0,4
ZG20SiMn
JB/T 4297-86
EZB 1162-92
+QT 100 300 500 - 650 24 30 45 20 - - 0,23 0,6
1,00 -
1,50
0,025 0,025 0,30 0,15 0,4
ZG20MnMo JB/T 6402-92 +QT 100 295 490 16 - 39 (KCU) - -
0,17 -
0,23
0,20 -
0,40
1,10 -
1,40
0,035 0,035 -
0,20 -
0,35
-
Cu max.
0,30
ZG20CrMoV JB/T 7024-93 +QT
-
0,50 -
0,80
0,035
1.0619 GS-25N +N
0,23 -
0,30
22 32 35
Q
u
e
n
c
h
e
d

a
n
d

t
e
m
p
e
r
e
d

s
t
e
e
l

c
a
s
t
i
n
g
s
H
e
a
t
-
r
e
s
i
s
t
a
n
t

s
t
e
e
l

c
a
s
t
i
n
g
s
+N
100 240
230 450
- -
+N is not comparison, +QT-steel is permisible for
comparison,
0,035
0,80 -
1,20
0,20 -
0,30
-
0,30 -
0,37
0,30 -
0,50
0,80 -
1,20
0,20 -
0,30
quenched
and
tempered in
air
620 - 770
10 - 16 20
Liquid
quenched
and
tempered
V I
V II
- 0,40 -
0,30 Cu
0,03 V
0,02 0,30
0,30 -
0,37
0,60
+QT
- 27
20
0,20 -
0,45
- 0,04 0,04 -
0,50 -
0,80
- - - -
420-600 22 20 - 0,03
0,50-
1,20
0,18-
0,23
0,60
- - - +QT 1.7232 GS-50CrMo4 150 - 520 730 11 -
Material do not use for new design. 1.7220 - GS-34CrMo4V
DIN 17205
(Invalid)
0,50 -
0,80
0,02 0,015
Flame and induction hardening steel castings G50CrMo4 - -
0,90 -
1,20
0,15 -
0,25
-
0,46 -
0,54
520 740 - 880
0,035
0,46 -
0,54
0,25 -
0,50
0,50 -
0,80
0,035
-
0,25 -
0,50
200 - 260 11 - 34 20
22 -
0,50 -
0,80
0,035 - - 0,035
0,90 -
1,20
0,15 -
0,25
-
- -
0,12
ZG 230-450 EZB 1165-93 +QT 230 450
0,50 -
1,20
0,03 0,02 - - - 40 20 - -
0,18 -
0,23
0,60 +QT 100 240 420 - 600
+QT 100 245 440 - 590 22 -
- -
0,04 - - -
0,23 -
0,30
0,20 -
0,45
22 32
0,50 -
0,80
0,04 35 20 - -
0,50 -
1,00
0,025 0,02 - 27 20 - -
0,15 -
0,23
0,60
0,02
1,00 -
1,50
0,45 -
0,65
- - -
0,40 -
0,60
- - -
+QT
0,15 -
0,20
0,60
0,50 -
1,00
0,02 27 20 - - 100 315 490 - 690 20 - G17CrMo5-5 DIN EN 10213 1.7357 GS-17CrMo55V
Not known Not known
G20Mo5 DIN EN 10213 1.5419 GS-22Mo4
GP240GH DIN EN 10213 1.0619 GS-25V
ZG 50Cr1Mo
JB/T 6402-92
EZB 1162-92
SEW 835
GP240GH
ZG 230-450 EZB 1165-93
ZG 35Cr1Mo
JB/T 6402-92
EZB 1162-92
DIN EN 10213
SN359-1 : 2012-06
Notice
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d
p
o
i n
t ,
p
r
o
o
f s
t r
e
s
s
T
e
n
s
i l e

s
t r
e
n
g
t h
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t u
r
e
R
e
d
u
c
t i o
n
o
f
a
r
e
a
N
o
t c
h

t o
u
g
h
n
e
s
s

(
2
0
C
)
T
e
s
t -
t e
m
p
e
r
a
t u
r
e
F
a
t i g
u
e

s
t r
e
n
g
t h
H
a
r
d
n
e
s
s

a
f t e
r

a
n
n
e
a
l i n
g
Heat-
treatment
Former
designation
ZG15Cr1Mo1V
GB/T 16253-
1996
+QT 420 590-740 15 - 24 20
0,13-
0,20
0,30-
0,60
0,50-
0,80
0,035 0,035
1,20-
1,60
0,90-
1,20
V 0,15-
0,35
ZG23Cr12Mo1NiVG
GB/T 16253-
1996
+QT 540 740 - 880 15 - 21 20
0,20-
0,26
0,20-
0,40
0,50-
0,70
0,035 0,035
11,3 -
12,3
1,00-
1,20
0,70-
1,00
H
e
a
t
-
r
e
s
i
s
t
a
n
t

s
t
e
e
l

c
a
s
t
i
n
g
s
G17CrMoV5-10 DIN EN 10213 1.7706 150 +QT -
V 0,20 -
0,30
Sn max.
0,025
0,015
1,20 -
1,50
0,90 -
1,10
20 - -
0,15 -
0,20
0,60
0,50 -
0,90
GS-17CrMoV5 11V 440 590 - 780 15 - 27
GX23CrMoV12-1 DIN EN 10213 1.4931 GX-22CrMoV12 1
-
740 - 880 15 - +QT 150 540 0,40 20
0,02
0,02
11,30
-
12,20
1,00 -
1,20
max.
1,00
0,50 -
0,80
0,03 -
V 0,25 -
0,35
W max.
0,50
- -
0,20 -
0,26
27
SN359-1 : 2012-06
Anhang/Appendix B3 (normativ) - Comparison of german and chinese material properties, cast irons
Notice
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d
p
o
i n
t ,
p
r
o
o
f s
t r
e
s
s
T
e
n
s
i l e

s
t r
e
n
g
t h
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t u
r
e
R
e
d
u
c
t i o
n
o
f
a
r
e
a
N
o
t c
h

t o
u
g
h
n
e
s
s

(
2
0
C
)
T
e
s
t -
t e
m
p
e
r
a
t u
r
e
F
a
t i g
u
e

s
t r
e
n
g
t h
H
a
r
d
n
e
s
s

a
f t e
r

a
n
n
e
a
l i n
g
10 - 20 - 180 - - - - 90 250
20 - 40 - 155 - - - - - 235
40 - 80 - 130 - - - - - 235
HT20-40 GB 9439-88 - - - 200 - - - - - -
HT200 EZB 1173-94 - - - 200 - - - - - -
EZB-Standards are work-standards from CHINA NATIONAL
ERZHONG GROUP
10 - 20 - 225 - - - - 120 265
20 - 40 - 195 - - - - - 250
40 - 80 - 170 - - - - - 250
10 - 20 - 270 - - - - 140 265
20 - 40 - 240 - - - - - 265
40 - 80 - 210 - - - - - 265
- - 250 - - - -
max. or range %
Referenc composition, at supplier's discretion -
-
Without heat
treatment or
stress
reliving
-
GB 9439-88
G
r
e
y

c
a
s
t

i
r
o
n
min. or range
GG-20
GGL-20
-
Material
300 -
-
Heat-
treatment
- -
-
- - -
EN-GJL-200
EN-GJL-250
HT250
EN-GJL-300 EN-GJL-300
Former
designation
HT25-47
GG-25
GGL-25
GG-30
GGL-30
HT300 EZB 1173-94
EN-GJL-200
HT30-54 GB 9439-88
EN-GJL-250
DIN EN 1561
DIN EN 1561
EZB 1173-94
DIN EN 1561
- - 250 - - - - -
Referenc composition, at supplier's discretion
ERZHONG GROUP
- Referenc composition, at supplier's discretion
ERZHONG GROUP
-
- - -
-
- -
- - Referenc composition, at supplier's discretion - - 300 - - -
GGL-320MoCr8 Elevated temperature resistant and wear resistant -
0,5 -
1,0
0,20 0,12
No conversion
0,20 -
0,40
0,60 -
1,00
-
3,0 -
3,4
- - -
1,6 -
2,4
350 max. 280
SN359-1 : 2012-06
Notice
T
h
i c
k
n
e
s
s
o
r

d
i a
m
e
t e
r
Y
i e
l d
p
o
i n
t ,
p
r
o
o
f s
t r
e
s
s
T
e
n
s
i l e

s
t r
e
n
g
t h
E
l o
n
g
a
t i o
n
a
t
f r
a
c
t u
r
e
R
e
d
u
c
t i o
n
o
f
a
r
e
a
N
o
t c
h

t o
u
g
h
n
e
s
s

(
2
0
C
)
T
e
s
t -
t e
m
p
e
r
a
t u
r
e
F
a
t i g
u
e

s
t r
e
n
g
t h
H
a
r
d
n
e
s
s

a
f t e
r

a
n
n
e
a
l i n
g
max. or range %
min. or range
Material
Heat-
treatment
Former
designation
30 250 400 15 - - - - 130 - 180
30 - 60 250 390 14 - - - - -
60 - 200 240 370 11 - - - - -
30 250 400 18 - - - - 130 - 180
30 - 60 250 390 15 - - - - -
60 - 200 240 370 12 - - - - -
30 320 500 7 - - - - 170 - 230
30 - 60 300 450 7 - - - - -
60 - 200 290 420 5 - - - - -
30 370 600 3 - - - - 190 - 270
30 - 60 360 600 2 - - - - -
60 - 200 340 550 1 - - - - -
30 420 700 2 - - - - 225 - 305
30 - 60 400 700 2 - - - - -
60 - 200 380 660 1 - - - - -
30 480 800 2 - - - - 245 - 335
EN-GJS-400-15U DIN EN 1563 EN-JS1072 GGG-40 - Referenc composition, at supplier's discretion
U = test bar attached
-
GB 1348-88
EZB 1174-94
- - 250 400 15
- - - 130 - 180 18 - Referenc composition, at supplier's discretion
130 - 180 QT400-15
EN-GJS-400-18U DIN EN 1563 EN-JS1062
ERZHONG GROUP
- - - - Referenc composition, at supplier's discretion
GGG-40 -
EN-GJS-600-3U DIN EN 1563 EN-JS1092 GGG-60 -
- 170 - 230
EN-GJS-500-7U DIN EN 1563 EN-JS1082 GGG-50 -
- QT500-7
GB 1348-88
EZB 1174-94
320
GB 1348-88
EZB 1174-94
- - 600 3 - - 370 190 - 270 Referenc composition, at supplier's discretion
- -
- QT700-2
GB 1348-88
EZB 1174-94
- - Referenc composition, at supplier's discretion
DIN EN 1563 EN-JS1102 GGG-70 - Referenc composition, at supplier's discretion
QT600-3
QT800-2
GB 1348-88
EZB 1174-94
- - 480
- - - 225 - 305 420 700 2
2
M
a
l
l
e
a
b
l
e

c
a
s
t

i
r
o
n
max. 220
No conversion
245 - 335
No conversion
max. 200
- - - -
EN-GJMW-360-12 DIN EN 1562 EN-JM1020 GTW-38 -12 - Referenc composition, at supplier's discretion
- EN-GJMW-400-5 DIN EN 1562 EN-JM1030
190 360 5
Referenc composition, at supplier's discretion GTW-40 -05
12
400 5 12 220
QT400-18 GB 1348-88 - - 250 400
N
u
d
u
l
a
r

c
a
s
t

i
r
o
n
EN-GJS-800-2U DIN EN 1563
EN-GJS-700-2U
800
to be agreed between the manufacturer and the purchaser
EN-JS1112 GGG-80 -
500 7 - - -
SN359-1 : 2012-06
Anhang/Appendix B4 (normativ) - Comparison of German and Chinese material properties, Non-ferrous metals
Notice
T
h
i c
k
n
e
s
s

o
r

d
i a
m
e
t
e
r
Y
i e
l d
p
o
i n
t
,

p
r
o
o
f

s
t
r
e
s
s
T
e
n
s
i l e

s
t
r
e
n
g
t
h
E
l o
n
g
a
t
i o
n

a
t

f
r
a
c
t
u
r
e
R
e
d
u
c
t
i o
n

o
f

a
r
e
a
N
o
t
c
h

t
o
u
g
h
n
e
s
s

T
e
s
t
-
t
e
m
p
e
r
a
t
u
r
e
F
a
t
i g
u
e

s
t
r
e
n
g
t
h
H
a
r
d
n
e
s
s

a
f
t
e
r

a
n
n
e
a
l i n
g
mm MPa MPa % % J C Mpa HBW10 Cu Sn Pb Ni Sb Al Zn Si Fe other
GK-CuSn10Zn DIN EN 1982 - GK-S1 - 8,80 160 290 20 - - - - 85
86,0 -
89,0
9,0 -
11,0
- - - -
1,0 -
3,0
ZCuSn10Zn2
CuSn7Zn4Pb7-C-GS DIN EN 1982
CC493K-
GS
G-CuSn7ZnPb - 8,80 120 230 15 - - - 110 60
81,0 -
85,0*
6,0 -
8,0
5,0 -
8,0
2,00 0,3 0,01
2,0 -
5,0
0,01 0,2
P+S
je max.
0,10
ZCuSn7Zn4Pb6-S 120 240 15 - - - - 65
remai
nder
6,0 -
8,0
5,0 -
7,0
- - -
3,0 -
5,0
- - -
CuSn7Zn4Pb7-C-GZ DIN EN 1982 CC493K-GZ GZ-CuSn7ZnPb - 8,80 120 260 12 - - - 110 70
81,0 -
85,0*
6,0 -
8,0
5,0 -
8,0
2,00 0,3 0,01
2,0 -
5,0
0,01 0,2
P+S
je max.
0,10
YZB-Standards are work-standards from CHINA
FIRST HEAVY INDUSTRIE
ZCuSn7Zn4Pb6-Li 130 270 13 - - - - 75
remai
nder
6,0 -
8,0
5,0 -
7,0
- - -
3,0 -
5,0
- - -
CuSn7Zn4Pb7-C-GC DIN EN 1982
CC493K-
GC
GC-CuSn7ZnPb - 8,80 120 260 12 - - - 110 70
81,0 -
85,0*
6,0 -
8,0
5,0 -
8,0
2,00 0,3 0,01
2,0 -
5,0
0,01 0,2
P+S
je max.
0,10
ZCuSn7Zn4Pb6-La 120 270 16 - - - - 70
remai
nder
6,0 -
8,0
5,0 -
7,0
- - -
3,0 -
5,0
- - -
CuSn10Pb10-C-GS DIN EN 1982
CC495K-
GS
G-CuPb10Sn - 9,00 80 180 8 - - - - 60
78,0 -
82,0
9,0 -
11,0
8,0 -
11,0
2,00 0,5 0,01 2,00 0,01 0,25
P+S
je max.
0,10
GS = sand casting = S
ZCuPb10Sn10-S 110 220 6 - - - - -
remai
nder
9,0 -
11,0
8,0 -
11,0
GZ = centrifugal casting = Li
ZCuSn13Pb9-S 9,10 170 205 2 - - - - -
remai
nder
12,0-
13,5
8,0 -
11,0
8,0-
10,0
2,25
0,7
5
0,15 GC = continuously cast material = La
ZCuSn13Pb9-J 9,10 170 205 2 - - - - -
remai
nder
12,0-
13,5
8,0 -
11,0
8,0-
10,0
2,25
0,7
5
0,15 Metal mold = J
CuSn10Pb10-C-GZ DIN EN 1982
CC495K-
GZ
G-CuPb10Sn - 9,00 110 220 6 - - - - 70
78,0 -
82,0
9,0 -
11,0
8,0 -
11,0
2,00 0,5 0,01 2,00 0,01 0,25
P+S
je max.
0,10
ZCuPb10Sn10-Li 110 220 6 - - - - -
remai
nder
9,0 -
11,0
8,0 -
11,0
Material
GB/T 1176-1987
EZB 1179-93
min. or range
YZB 267-2002
EZB 1179-93
Not known
EZB 1179-93
GB/T 1176-1987
YZB 267-2002
GB/T 1176-1987
Not known
C
o
p
p
e
r
-
t
i
n
-
l
e
a
d

c
a
s
t

a
l
l
o
y

(
c
a
s
t

t
i
n
-
l
e
a
d
-
b
r
o
n
z
e
)
Former
designation
Heat-
treatment
max. or range %
C
o
p
p
e
r
-
t
i
n
-
z
i
n
c

c
a
s
t

a
l
l
o
y
s

(
r
e
d

b
r
a
s
s
)
SN359-1 : 2012-06
Notice
T
h
i c
k
n
e
s
s

o
r

d
i a
m
e
t
e
r
Y
i e
l d
p
o
i n
t
,

p
r
o
o
f

s
t
r
e
s
s
T
e
n
s
i l e

s
t
r
e
n
g
t
h
E
l o
n
g
a
t
i o
n

a
t

f
r
a
c
t
u
r
e
R
e
d
u
c
t
i o
n

o
f

a
r
e
a
N
o
t
c
h

t
o
u
g
h
n
e
s
s

T
e
s
t
-
t
e
m
p
e
r
a
t
u
r
e
F
a
t
i g
u
e

s
t
r
e
n
g
t
h
H
a
r
d
n
e
s
s

a
f
t
e
r

a
n
n
e
a
l i n
g
Material Mechanical properties
min. or range
Group Material designation Standard No. Former
designation
Heat-
treatment
max. or range %
CuSn10-C-GS DIN EN 1982
CC480K-
GS
G-CuSn10 - 8,60 140 260 7 - - - - 80
85,0 -
88,5
11,0 -
13,0
0,7 2,00 0,15 0,01 - 0,01 0,20
P max.
0,60
S max.
ZCuSn10P1-S 140 260 10 - - - - 80
remai
nder
11,0 -
13,0
1,0 -
2,0
- - - - - - -
CuSn10-C-GZ DIN EN 1982
CC480K-
GZ
GZ-CuSn10 - 8,60 150 280 5 - - - - 90
85,0 -
88,5
11,0 -
13,0
0,7 2,00 0,15 0,01 - 0,01 0,20
P max.
0,60
S max.
ZCuSn10P1-Li EZB 1179-93
140 260 10 - - - - 80
remai
nder
11,0 -
13,0
1,0 -
2,0
- - - - - - -
CuSn10-C-GC DIN EN 1982
CC480K-
GC
GC-CuSn10 - 8,60 150 300 6 - - - - 90
85,0 -
88,5
11,0 -
13,0
0,7 2,00 0,15 0,01 - 0,01 0,20
P max.
0,60
S max.
ZCuSn10P1-La 170 300 10 - - - - 90
remai
nder
11,0 -
13,0
-
1,5 -
2,5
- - - - - -
CuSn12-C-GS DIN EN 1982
CC483K-
GS
G-CuSn12 - 8,60 140 260 7 - - - - 80
85,0 -
88,5
11,0 -
13,0
0,7 2,00 0,15 0,01 - 0,01 0,20
P max.
0,60
S max.
ZCuSn12Pb1-S 140 260 10 - - - - 80
remai
nder
11,0 -
13,0
1,0 -
2,0
- - - - - - -
ZCuSn13Pb9-S 9,10 170 205 2 - - - -
remai
nder
12,0-
13,5
8,0 -
10,0
- - - 0,75 - - P<0,05
CuSn12-C-GZ DIN EN 1982
CC483K-
GZ
GZ-CuSn12 - 8,60 150 280 5 - - - - 90
85,0 -
88,5
11,0 -
13,0
0,7 2,00 0,15 0,01 - 0,01 0,20
P max.
0,60
S max.
ZCuSn12Ni2-Li
ZCuSn10Pb1
EZB 1179-93
140 260 10 - - - - 80
remai
nder
11,0 -
13,0
1,0 -
2,0
- - - - - - -
CuSn12-C-GC DIN EN 1982
CC483K-
GC
GC-CuSn12 - 8,60 150 300 6 - - - - 90
85,0 -
88,5
11,0 -
13,0
0,7 2,00 0,15 0,01 - 0,01 0,20
P max.
0,60
S max.
ZCuSn12Ni2-La 170 300 10 - - - - 90
remai
nder
11,0 -
13,0
-
1,5 -
2,5
- - - - - -
CuSn12Ni2-C-GS DIN EN 1982
CC484K-
GS
G-CuSn12Ni - 8,60 160 280 12 - - - - 85
84,5 -
87,5
11,0 -
13,0
0,3
1,5 -
2,5
0,05 0,01 0,4 0,01 0,20
P 0,05 -
0,40
S max.
ZCuSn12Ni2-S 160 280 14 - - - - 90
remai
nder
11,0 -
13,0
-
1,5 -
2,5
- - - - - -
CuSn12Ni2-C-GZ DIN EN 1982
CC484K-
GS
GZ-CuSn12Ni - 8,60 180 300 8 - - - - 95
84,5 -
87,5
11,0 -
13,0
0,3
1,5 -
2,5
0,05 0,01 0,4 0,01 0,20
P 0,05 -
0,40
S max.
ZCuSn12Ni2-Li 180 300 8 - - - - 100
remai
nder
11,0 -
13,0
-
1,5 -
2,5
- - - - - -
EZB 1179-93
EZB 1179-93
EZB 1179-93
EZB 1179-93
EZB 1179-93
EZB 1179-93
C
o
p
p
e
r
-
t
i
n

c
a
s
t

a
l
l
o
y

(
i
n

b
r
o
n
z
e
)
YZB 267-2002
SN359-1 : 2012-06
Notice
T
h
i c
k
n
e
s
s

o
r

d
i a
m
e
t
e
r
Y
i e
l d
p
o
i n
t
,

p
r
o
o
f

s
t
r
e
s
s
T
e
n
s
i l e

s
t
r
e
n
g
t
h
E
l o
n
g
a
t
i o
n

a
t

f
r
a
c
t
u
r
e
R
e
d
u
c
t
i o
n

o
f

a
r
e
a
N
o
t
c
h

t
o
u
g
h
n
e
s
s

T
e
s
t
-
t
e
m
p
e
r
a
t
u
r
e
F
a
t
i g
u
e

s
t
r
e
n
g
t
h
H
a
r
d
n
e
s
s

a
f
t
e
r

a
n
n
e
a
l i n
g
min. or range
designation
Heat-
treatment
max. or range %
CuSn12Ni2-C-GC DIN EN 1982
CC484K-
GS
GC-CuSn12Ni - 8,60 180 300 10 - - - - 95
84,5 -
87,5
11,0 -
13,0
0,3
1,5 -
2,5
0,05 0,01 0,4 0,01 0,20
P 0,05 -
0,40
S max.
ZCuSn12Ni2-La 170 300 10 - - - - 90
remai
nder
11,0 -
13,0
-
1,5 -
2,5
- - - - - -
CuSn11Pb2-C-GS DIN EN 1982
CC482K-
GS
G-CuSn12Pb - 8,70 130 240 5 - - - - 80
83,5 -
87,0
10,5 -
12,5
0,7 -
2,5
2,00 0,2 0,01 2 0,01 0,20
P
max.0,40
S max.
ZCuSn12Pb1-S 140 260 10 - - - - 80
remai
nder
11,0 -
13,0
1,0 -
2,0
- - - - - - -
CuSn11Pb2-C-Gz DIN EN 1982
CC482K-
GZ
GZ-CuSn12Pb - 8,70 150 280 5 - - - - 90
83,5 -
87,0
10,5 -
12,5
0,7 -
2,5
2,00 0,2 0,01 2 0,01 0,20
P
max.0,40
S max.
ZCuSn12Pb1-Li 150 280 5 - - - - 90
remai
nder
11,0 -
13,0
1,0 -
2,0
- - - - - - -
CuSn11Pb2-C-GC DIN EN 1982
CC482K-
GZ
GC-CuSn12Pb - 8,70 150 280 5 - - - - 90
83,5 -
87,0
10,5 -
12,5
0,7 -
2,5
2,00 0,2 0,01 2 0,01 0,20
P
max.0,40
S max.
ZCuSn12Pb1-La 150 280 7 - - - - 90
remai
nder
11,0 -
13,0
1,0 -
2,0
- - - - - - -
140 260 10 - - - - 80
150 280 5 - - - - 90
140 280 7 - - - - 85
DF-5(1) 170 330 4 - - - - 88
DF-5(2) 200 540 15 - - - - 110
DF-5(3) 250 630 16 - - - - 157
DF-5(4) 400 740 7 - - - - 167
DF-5(5) 200 475 18 - - - - 110
Basic-material is 2.1061.01 CuSn12Pb 8,70 devagleit
TM
dg02
EZB 1179-93
-
EZB 1179-93
DF is the product from Dalian Fangyan Composite
Material Bearings Co.Ltd. (www.dfbearing.cn)
devagleit
TM
is the product from Federal Mogul
(www.deva.de)
84,0 -
87,0
11,0 -
13,0
1,0 -
2,0
2,0 0,2 -
EZB 1179-93
EZB 1179-93
Chemical composition not known
-
Basic-material not known
C
o
p
p
e
r
-
t
i
n

c
a
s
t

a
l
l
o
y

(
i
n

b
r
o
n
z
e
)
SN359-1 : 2012-06
Notice
T
h
i c
k
n
e
s
s

o
r

d
i a
m
e
t
e
r
Y
i e
l d
p
o
i n
t
,

p
r
o
o
f

s
t
r
e
s
s
T
e
n
s
i l e

s
t
r
e
n
g
t
h
E
l o
n
g
a
t
i o
n

a
t

f
r
a
c
t
u
r
e
R
e
d
u
c
t
i o
n

o
f

a
r
e
a
N
o
t
c
h

t
o
u
g
h
n
e
s
s

T
e
s
t
-
t
e
m
p
e
r
a
t
u
r
e
F
a
t
i g
u
e

s
t
r
e
n
g
t
h
H
a
r
d
n
e
s
s

a
f
t
e
r

a
n
n
e
a
l i n
g
min. or range
designation
Heat-
treatment
max. or range %
CuAl10Fe5Ni5-C-GS DIN EN 1982
CC333K-
GS
G-CuAl10Ni - 7,60 250 600 13 - - - - 140
76,0 -
83,0
0,1 0,03
4,0 -
8,0
-
8,5 -
10,5
0,5 0,1
4,0 -
5,5
see
Standard
ZCuAl10Ni6Fe5-S 270 600 12 - - - - 140
remai
nder
- -
4,5 -
6,5
-
8,8 -
10,8
- -
3,5 -
5,5
-
ZCuAl10Fe4Ni2-S 7,40 205 515 12 - - - - >83 2,5
10,0 -
11,5
3,0 -
5,0
CuAl10Fe5Ni5-C-GZ DIN EN 1982
CC333K-
GS
G-CuAl10Ni - 7,60 280 650 13 - - - - 150
76,0 -
83,0
0,1 0,03
4,0 -
8,0
-
8,5 -
10,5
0,5 0,1
4,0 -
5,5
see
Standard
ZCuAl10Ni6Fe5-Li 300 700 13 - - - - 160
remai
nder
- -
4,5 -
6,5
-
8,8 -
10,8
- -
3,5 -
5,5
-
ZCuAl10Fe4Ni2-Li 7,40 205 515 12 - - - - >83 2,5
10,0 -
11,5
3,0 -
5,0
270 600 12 - - - - 140
300 600 14 - - - - 150
300 700 13 160
300 700 13 - - - - 160
DF-5(1) 170 330 4 - - - - 88
DF-5(2) 200 540 15 - - - - 110
DF-5(3) 250 630 16 - - - - 157
DF-5(4) 400 740 7 - - - - 167
DF-5(5) 200 475 18 - - - - 110
317
(365)
620
(724)
10
(14)
14 - - -
179
(202)
317
(386)
655
(758)
10
(16)
16
179
(207)
Main-Metall 4,40
220 -
300
280 - 320 5 - 15 - - - - 80 - 110
1,0 -
5,0
- - - -
35 -
40
rema
inder
- - -
180 500 15 - - - - 115
Werte erreichen nicht die von APMCO 18-23, daher
nur mit Einschrnkung verwendbar.
Main-Metall is the product from Main-Metall Foundry.
(www.main-metall.com)
Produkt from AMPCO Metal Deutschland GmbH
(www-ampcometal.net)
Klammerwerte sind Richtwerte.
AMPCO 18-23(GS)**
AMPCO 18-23(GZ)***
- - - - 10,50 -
Not according to standard, CuAl alloy with special
guaranteed values.
Not according to standard, CuAl alloy with special
guaranteed values.
No conversion
8,5 -
11,0
3,5 -
5,5
0,5
8,5 -
11,0
-
2,0 -
4,0
W
h
i
t
e

b
r
o
n
z
e
C
o
p
p
e
r
-
a
l
u
m
i
n
u
m

b
r
o
n
z
e
remai
nder
devagleit
TM
dg03
ZCuAl10Fe3 (GS)
-
EZB 1179-93
3,5
Chemical composition not known
Basic-material is 2.0975.01 CuAl10Ni
Basic-material not known
YZB 267-2002
7,60
EZB 1179-93
-
2,0 -
8,5
- -
YZB 267-2002
min.
75
EZB 1179-93
remai
nder
SN359-1 : 2012-06
Notice
T
h
i c
k
n
e
s
s

o
r

d
i a
m
e
t
e
r
Y
i e
l d
p
o
i n
t
,

p
r
o
o
f

s
t
r
e
s
s
T
e
n
s
i l e

s
t
r
e
n
g
t
h
E
l o
n
g
a
t
i o
n

a
t

f
r
a
c
t
u
r
e
R
e
d
u
c
t
i o
n

o
f

a
r
e
a
N
o
t
c
h

t
o
u
g
h
n
e
s
s

T
e
s
t
-
t
e
m
p
e
r
a
t
u
r
e
F
a
t
i g
u
e

s
t
r
e
n
g
t
h
H
a
r
d
n
e
s
s

a
f
t
e
r

a
n
n
e
a
l i n
g
min. or range
designation
Heat-
treatment
max. or range %
CuZn35Mn2Al1Fe1-GS DIN EN 1982
CC765S-
GS
G-CuZn35Al1 - 8,60 170 450 20 - - - - 110
57,0 -
65,0
1,00 0,5 6,00 0,08
0,5 -
2,5
rema
inder
-
0,5 -
2,0
Mn 0,5 -
3,0
ZCuZn35Al1Fe1Mn2-S
56,0 -
65,0
-
1,0 -
2,0
- -
0,5 -
2,0
rema
inder
-
0,5 -
2,0
Mn0,5 -
3,0
CuZn35Mn2Al1Fe1-GZ DIN EN 1982
CC765S-
GZ
G-CuZn35Al1 - 8,60 200 500 18 - - - - 120
57,0 -
65,0
1,00 0,5 6,00 0,08
0,5 -
2,5
rema
inder
-
0,5 -
2,0
Mn 0,5 -
3,0
ZCuZn35Al1Fe1Mn2-Li
56,0 -
65,0
-
1,0 -
2,0
- -
0,5 -
2,0
rema
inder
-
0,5 -
2,0
Mn0,5 -
3,0
CuZn34Mn3Al2Fe1-C-GS DIN EN 1982
CC764S-
GS
G-CuZn34Al2 - 8,40 250 600 15 - - - - 140
55,0 -
66,0
0,3 0,3 3,00 0,05
1,0 -
3,0
rema
inder
-
0,5 -
2,5
Mn 1,0 -
4,0
ZCuZn34Al2Fe2Mn3-S
55,0 -
65,0
-
1,0 -
2,0
- -
1,0 -
3,0
rema
inder
-
0,5 -
2,5
Mn0,5 -
4,0
CuZn34Mn3Al2Fe1-C-GZ DIN EN 1982
CC764S-
GZ
G-CuZn34Al2 - 8,40 260 620 14 - - - - 150
55,0 -
66,0
0,3 0,3 3,00 0,05
1,0 -
3,0
rema
inder
-
0,5 -
2,5
Mn 1,0 -
4,0
ZCuZn34Al2Fe2Mn3-Li
55,0 -
65,0
-
1,0 -
2,0
- -
1,0 -
3,0
rema
inder
-
0,5 -
2,5
Mn0,5 -
4,0
CuZn25Al5Mn4Fe3-C-GS DIN EN 1982
CC762S-
GS
G-CuZn25Al5 - 8,20 450 750 8 - - - - 180
60,0 -
67,0
0,2 0,2 3,00 0,03
3,0 -
7,0
rema
inder
-
1,5 -
4,0
Mn 2,5 -
5,0
ZCuZn25Al5Fe3Mn4-S
60,0 -
67,0
-
1,0 -
2,0
- -
3,0 -
7,0
rema
inder
-
1,5 -
4,0
Mn 2,5 -
5,0
ZCuZn25Al6Fe3Mn3-S 8,50 380 725 10
60,0 -
66,0
0,2 0,2 3,00
4,5 -
7,0
rema
inder
0,1
2,0 -
4,0
Mn 1,5 -
4,0
CuZn25Al5Mn4Fe3-C-GZ DIN EN 1982
CC762S-
GZ
G-CuZn25Al5 - 8,20 480 750 5 - - - - 190
60,0 -
67,0
0,2 0,2 3,00 0,03
3,0 -
7,0
rema
inder
-
1,5 -
4,0
Mn 2,5 -
5,0
ZCuZn25Al5Fe3Mn4-Li
60,0 -
67,0
-
1,0 -
2,0
- -
3,0 -
7,0
rema
inder
-
1,5 -
4,0
Mn 2,5 -
5,0
CuZn37Mn3Al2PbSi-R540 DIN EN 12164
CW731R-
R540
CuZn40Al2F54 - 8,10 ~280 540 15 ~150
57,0 -
59,0
0,4
0,2 -
0,8
1,00 -
1,3 -
2,3
rema
inder
0,3 -
1,3
1,00
Mn 1,5 -
3,0
C
o
p
p
e
r
-
z
i
n
c

c
a
s
t

a
l
l
o
y
s

(
c
a
s
t

s
p
e
c
i
a
l
n
b
r
a
s
s
)
No conversion
YZB 267-2002
EZB 1179-93
EZB 1179-93
EZB 1179-93
EZB 1179-93
EZB 1179-93
EZB 1179-93

SN359-1 Material Comparison German-Chinese 2012-06 E-1

Uploaded by

Copyright:

Available Formats

SN359-1 Material Comparison German-Chinese 2012-06 E-1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SN359-1 Material Comparison German-Chinese 2012-06 E-1

Uploaded by

Copyright:

Available Formats

June 2012

Table of contents Page

You might also like