Dispersion primer for absorbent substrates, screeds and concrete floors

UZIN PE 360 NEW

Applications:
Ready-to-use, fast-drying dispersion primer for pre-treatment
of absorbent mineral substrates, before the application of
cement- or calcium sulphate-based levelling compounds.
For use on floors and walls, preferably prior to levelling
work underneath floor coverings or wooden floors. For
interior and exterior applications.
Suitable for use on:
3
Absorbent substrates such as cement screeds, cement /
plaster-based levelling compounds or concrete
3
Calcium sulphate screeds / fibre-reinforced gypsum panels
3
Cement plasters, calcium/cement plasters, plasterboard
panels
Suitable for:
3
Application under low-slump and self-levelling levelling
compounds
3
Areas of high traffic in residential, commercial and
industrial areas
3
Hot water underfloor heating
3
Traffic from chair castors (DIN EN 12 529)
3
Not suitable for use as a primer under dispersion-based
wood floor adhesives
3
Use as a rapid construction system component
Product benefits / features:
As before, UZIN PE 360 NEW penetrates well into the sub-
strate, but also has film-forming properties, on account of
the innovative binder system used. As a result, UZIN PE
360 NEW not only offers subsequent levelling compounds
with a superb bonding primer, but is simultaneously
strongly reductive of the absorbency of the substrate.
Substrates sensitive to moisture are protected from the
water from levelling compounds and adhesives, while, for
extremely absorbent substrates, mixing water is drawn out
of the freshly applied levelling compound to a much lower
degree. The new formula for UZIN PE 360 NEW makes it
especially fast-drying, thus avoiding long setting times.
Ingredients: Modified styrene acrylic copolymer, wetting,
anti-foaming agent and preservative, water.
3
Ready for use
3
Very fast-drying
3
Excellent penetration, film forms immediately
3
High-yield
3
Spray application ready
3
GISCODE D 1/solvent-free
Technical data:
Packaging: Plastic canister
Pack sizes: 10 kg, 5 kg
Shelf life: min. 12 months
Colour liquid /dry: milk-blue / transparent
Consumption/coverage: 80 150 g/m
2
Minimum working temperatures: 10C at ground level
Ideal working temperature: 15 25 C at ground level
Drying time, can be covered after: 30 60 minutes*
*At 20C and 65% relative humidity. See also "Application table".
PRODUCT DATA SHEET
Universal Primer
Im
p
ro
v
e
d
b
a
rrie
r e
ffe
ct
UZIN | A Brand of Uzin Utz AG
D | Uzin Utz AG | Dieselstrae 3 | D-89079 Ulm | Telefon +49(0)731 4097-0 | Telefax +49(0)731 4097-214 | E-Mail [email protected] | Internet www.uzin.com
GB | Uzin Ltd. | Unit 2, Mitchell Court | Central Park, Rugby, Warwickshire | CV23 0UY | Phone +44 (0)1788 530 080 | Fax +44 (0)1788 536 508 | E-mail [email protected]
| Internet www.uzin.co.uk
Substrate preparation:
The substrate must be sound, load-bearing, dry, free from
cracks, clean and free from materials (dirt, oil, grease), that
would impair adhesion. Cement and calcium sulphate screeds
must be abraded and vacuumed off. Test the substrate in
accordance with applicable standards and bulletins and
report any deficiencies.
Any adhesion-reducing or unstable layers, e.g. release agents,
loose adhesives, compounds, covering or paint residues etc.
must be removed, e.g. by brushing, abrading, grinding or
shot-blasting. Thoroughly vacuum off loose material and
dust. Allow any primers that are applied to dry completely.
Refer to the product data sheets for other products used.
Application:
1. Allow the container to reach room temperature before
use and shake well, then decant the contents into a
clean, oval bucket.
2. Apply primer coat using a UZIN Nylon Fibre Roller, 25 cm/
14 mm (art. no.: 9394) or lambswool roller generously
and over the whole of the substrate surface. At edges or
walls, the primer coat can also be applied with a standard
paintbrush or other type of brush. Where substrates are
strongly absorbent, do not pour onto the substrate to
avoid excessive local saturation; in some cases, a second
coat may be required.
3. Clean tools with water immediately after use.
Application table:
Cement levelling compound on Coverage Drying time
cement screeds, cement
levelling compounds or concrete
80 150 g /m
2
Approx. 30 min.*
Calcium sulphate screeds,
plaster-based precast concrete, 80 120 g /m
2
Approx. 60 min.*
plaster substrates, render
Weakly absorbent,
less porous substrates
80 100 g /m
2
Approx. 60 min.*
Plaster levelling compound on Coverage Drying time
calcium sulphate screeds,
plaster-based precast concrete
80 120 g /m
2
Approx. 30 min.*
*At 20C and 65% relative humidity.
Important notes:
3
Shelf life min. 12 months in original packaging when stored in
moderately cool conditions. Frost-resistant to 4C. Re-seal
opened containers tightly and use contents as quickly as
possible. Allow primer to reach room temperature before
processing.
3
Optimum working at 15 25C, floor temperature over 15C
and rel. humidity below 65 %. Low temperatures and high
humidity will delay whilst high temperatures and low humidity
will accelerate the drying time.
3
A second coat is recommended on strongly absorbent sub-
strates.
3
Allow levelling compound to dry completely, apply UZIN
PE 360 universal primer as an intermediate primer and apply
subsequent levelling compound after drying. The second
application must not exceed the thickness of the first one.
3
Where levelling produces layers exceeding 10 mm, an epoxy
resin primer such as UZIN PE 460 (sanded) is required.
3
Not suitable for use on water-soluble adhesive remnants (e.g.
spent sulphite lye adhesives) or tackifiers, or old bitumen
adhesive remnants. In such cases, use a suitable primer from
the current UZIN product range.
3
Not suitable for use as a moisture barrier.
3
Not suitable for use as a primer directly under wood floor
adhesives.
3
Do not use on chipboard panels, OSB panels or other wood-
based substrates.
3
Do not use on non-mineral substrates or on magnesium- and
xylolite-based screeds.
3
Observe generally acknowledged industry and technology
best practice when laying floor coverings, plus the respective
applicable national standards. (e.g. EN, DIN, VOB, OE, SIA,
etc.) The following standards and bulletins offer supporting
information and /or are recommended reading:
DIN 18 365 "Working with floor coverings"
TKB publication "Assessment and preparation of substrates
for floor covering and wood flooring installation"
BEB publication "Assessment and preparation of substrates"
Protection of the workplace and the environment:
GISCODE D1 solvent-free (TRGS 610). The use of skin protection lotion is recom-
mended as a rule. Store out of the reach of children. Ensure thorough ventilation
during and after working /drying! Do not eat, drink or smoke while working with the
product. In the event of contact with the eyes or skin, rinse immediately with plenty
of water. Do not dispose of into the sewer system, open water or the soil. Clean
tools with water and soap immediately after use.
To the best of current knowledge, does not emit any relevant emissions of formalde-
hyde, harmful substances or other volatile organic compounds (VOCs). Odourless as
well as ecologically and physiologically harmless when fully dried. Basic prerequisites
for optimal interior air quality after floor covering work depend on installation
conditions conforming to standards, plus thoroughly-dried substrates, primers and
levelling compounds.
Disposal:
Collect and reuse product residues wherever possible. Do not dispose of into the
sewer system, open water or the soil. Empty, plastic containers (scraped clean and
drip-free) can be recycled [Interseroh]. Containers with liquid residues are classified
as special waste, as are collected liquid product residues. Containers with residues
that have dried solid are classified as construction/ household waste.
UZIN PE 360 NEW
The above information is based on our experience and careful investigations. The variety of associated materials and different construction and working conditions cannot be indi-
vidually checked or influenced by us. The quality of your work depends, therefore, on your own professional judgement and product usage. If in doubt, conduct a small test or obtain
technical advice. Observe the installation recommendations of the covering manufacturer. The publication of this Product Data Sheet invalidates all previous Product Information.
The respective updated version of this datasheet can be found on our Homepage under www.uzin.com. 02.12 | 02.12 | 0.000 | LD| leR