DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited.

NONRESIDENT
TRAINING
COURSE
June 1985
Mathematics, Basic
Math and Algebra
NAVEDTRA 14139
DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited.
Although the words he, him, and
his are used sparingly in this course to
enhance communication, they are not
intended to be gender driven or to affront or
discriminate against anyone.
COMMANDING OFFICER
NETPDTC
6490 SAUFLEY FIELD ROAD
PENSACOLA FL 32509-5237

7 Aug 2002

ERRATA #1

Specific Instructions and Errata for
Nonresident Training Course

MATHEMATICS, BASIC MATH AND ALGEGRA
NAVEDTRA 14139

1. No attempt has been made to issue corrections for errors in
typing, punctuation, etc., which do not affect your ability to
answer problems/questions.

2. In the assignment portion of the course, a question with no
choices is a True/False question. For True/False questions,
answer 1 for True and 2 for False.
i
PREFACE
By enrolling in this self-study course, you have demonstrated a desire to improve yourself and the Navy.
Remember, however, this self-study course is only one part of the total Navy training program. Practical
experience, schools, selected reading, and your desire to succeed are also necessary to successfully round
out a fully meaningful training program.
COURSE OVERVIEW: This course provides a review of basic arithmetic and continues through some of
the early stages of algebra. Emphasis is placed on decimals, percentages and measurements, exponents,
radicals and logarithms. Exercises are provided in factoring polynomials, linear equations, ratio, proportion
and variation, complex numbers, and quadratic equations. The final assignment affords the student an
opportunity to demonstrate what he or she has learned concerning plane figures, geometric construction and
solid figures, and slightly touches on numerical trigonometry.
THE COURSE: This self-study course is organized into subject matter areas, each containing learning
objectives to help you determine what you should learn along with text and illustrations to help you
understand the information. The subject matter reflects day-to-day requirements and experiences of
personnel in the rating or skill area. It also reflects guidance provided by Enlisted Community Managers
(ECMs) and other senior personnel, technical references, instructions, etc., and either the occupational or
naval standards, which are listed in the Manual of Navy Enlisted Manpower Personnel Classifications
and Occupational Standards, NAVPERS 18068.
THE QUESTIONS: The questions that appear in this course are designed to help you understand the
material in the text.
VALUE: In completing this course, you will improve your military and professional knowledge.
Importantly, it can also help you study for the Navy-wide advancement in rate examination. If you are
studying and discover a reference in the text to another publication for further information, look it up.
1980 Edition
Reprinted 1985
Published by
NAVAL EDUCATION AND TRAINING
PROFESSIONAL DEVELOPMENT
AND TECHNOLOGY CENTER
NAVSUP Logistics Tracking Number
0504-LP-026-7940
ii
Sailors Creed
I am a United States Sailor.
I will support and defend the
Constitution of the United States of
America and I will obey the orders
of those appointed over me.
I represent the fighting spirit of the
Navy and those who have gone
before me to defend freedom and
democracy around the world.
I proudly serve my countrys Navy
combat team with honor, courage
and commitment.
I am committed to excellence and
the fair treatment of all.
iv
INSTRUCTIONS FOR TAKING THE COURSE
ASSIGNMENTS
The text pages that you are to study are listed at
the beginning of each assignment. Study these
pages carefully before attempting to answer the
questions. Pay close attention to tables and
illustrations and read the learning objectives.
The learning objectives state what you should be
able to do after studying the material. Answering
the questions correctly helps you accomplish the
objectives.
SELECTING YOUR ANSWERS
Read each question carefully, then select the
BEST answer. You may refer freely to the text.
The answers must be the result of your own
work and decisions. You are prohibited from
referring to or copying the answers of others and
from giving answers to anyone else taking the
course.
SUBMITTING YOUR ASSIGNMENTS
To have your assignments graded, you must be
enrolled in the course with the Nonresident
Training Course Administration Branch at the
Naval Education and Training Professional
Development and Technology Center
(NETPDTC). Following enrollment, there are
two ways of having your assignments graded:
(1) use the Internet to submit your assignments
as you complete them, or (2) send all the
assignments at one time by mail to NETPDTC.
Grading on the Internet: Advantages to
Internet grading are:
you may submit your answers as soon as
you complete an assignment, and
you get your results faster; usually by the
next working day (approximately 24 hours).
In addition to receiving grade results for each
assignment, you will receive course completion
confirmation once you have completed all the
assignments. To submit your assignment
answers via the Internet, go to:
http://courses.cnet.navy.mil
Grading by Mail: When you submit answer
sheets by mail, send all of your assignments at
one time. Do NOT submit individual answer
sheets for grading. Mail all of your assignments
in an envelope, which you either provide
yourself or obtain from your nearest Educational
Services Officer (ESO). Submit answer sheets
to:
COMMANDING OFFICER
NETPDTC N331
6490 SAUFLEY FIELD ROAD
PENSACOLA FL 32559-5000
Answer Sheets: All courses include one
scannable answer sheet for each assignment.
These answer sheets are preprinted with your
SSN, name, assignment number, and course
number. Explanations for completing the answer
sheets are on the answer sheet.
Do not use answer sheet reproductions: Use
only the original answer sheets that we
providereproductions will not work with our
scanning equipment and cannot be processed.
Follow the instructions for marking your
answers on the answer sheet. Be sure that blocks
1, 2, and 3 are filled in correctly. This
information is necessary for your course to be
properly processed and for you to receive credit
for your work.
COMPLETION TIME
Courses must be completed within 12 months
from the date of enrollment. This includes time
required to resubmit failed assignments.
v
PASS/FAIL ASSIGNMENT PROCEDURES
If your overall course score is 3.2 or higher, you
will pass the course and will not be required to
resubmit assignments. Once your assignments
have been graded you will receive course
completion confirmation.
If you receive less than a 3.2 on any assignment
and your overall course score is below 3.2, you
will be given the opportunity to resubmit failed
assignments. You may resubmit failed
assignments only once. Internet students will
receive notification when they have failed an
assignment--they may then resubmit failed
assignments on the web site. Internet students
may view and print results for failed
assignments from the web site. Students who
submit by mail will receive a failing result letter
and a new answer sheet for resubmission of each
failed assignment.
COMPLETION CONFIRMATION
After successfully completing this course, you
will receive a letter of completion.
ERRATA
Errata are used to correct minor errors or delete
obsolete information in a course. Errata may
also be used to provide instructions to the
student. If a course has an errata, it will be
included as the first page(s) after the front cover.
Errata for all courses can be accessed and
viewed/downloaded at:
http://www.advancement.cnet.navy.mil
STUDENT FEEDBACK QUESTIONS
We value your suggestions, questions, and
criticisms on our courses. If you would like to
communicate with us regarding this course, we
encourage you, if possible, to use e-mail. If you
write or fax, please use a copy of the Student
Comment form that follows this page.
For subject matter questions:
E-mail: [email protected]
Phone: Comm: (850) 452-1001, Ext. 1520
or 1518
DSN: 922-1001, Ext. 1520 or 1518
FAX: (850) 452-1694
(Do not fax answer sheets.)
Address: COMMANDING OFFICER
NETPDTC N3222
6490 SAUFLEY FIELD ROAD
PENSACOLA FL 32509-5237
For enrollment, shipping, grading, or
completion letter questions
E-mail: [email protected]
Phone: Toll Free: 877-264-8583
Comm: (850) 452-1511/1181/1859
DSN: 922-1511/1181/1859
FAX: (850) 452-1370
(Do not fax answer sheets.)
Address: COMMANDING OFFICER
NETPDTC N331
6490 SAUFLEY FIELD ROAD
PENSACOLA FL 32559-5000
NAVAL RESERVE RETIREMENT CREDIT
If you are a member of the Naval Reserve, you
may earn retirement points for successfully
completing this course, if authorized under
current directives governing retirement of Naval
Reserve personnel. For Naval Reserve retire-
ment, this course is evaluated at 22 points,
which will be credited in units as shown below:
Unit 1 12 points upon satisfactory
completion of Assignments 1 through 6
Unit 2 10 points upon satisfactory
completion of Assignments 7 through 11
(Refer to Administrative Procedures for Naval
Reservists on Inactive Duty, BUPERSINST
1001.39, for more information about retirement
points.)
vii
Student Comments
Course Title: Mathematics, Basic Math and Algebra

NAVEDTRA: 14139 Date:
We need some information about you:
Rate/Rank and Name: SSN: Command/Unit

Street Address: City: State/FPO: Zip
Your comments, suggestions, etc.:
Privacy Act Statement: Under authority of Title 5, USC 301, information regarding your military status is
requested in processing your comments and in preparing a reply. This information will not be divulged without
written authorization to anyone other than those within DOD for official use in determining performance.
NETPDTC 1550/41 (Rev 4-00
MATHEMATICS, VOLUME 1
Figure 5-1.Place values including decimals.
Figure 5-2.Conversion
of a decimal fraction
to shortened form.
are zeros in the denominator of the fractional
form.
Figure 5-3 shows the fraction
24358
and
100000
what is meant when it is changed to the short-
ened form. This figure is presented to show
further that each digit of a decimal fraction
holds a certain position in the digit sequence
and has a particular value.
By the fundamental rule of fractions, it
should be clear that
5 50 500
= = . Writing
10 100 1000
the same values in the shortened way, we have
0.5 = 0.50 = 0.500. In other words, the value of
a decimal is not changed by annexing zeros at
the right-hand end of the number. This is not
46
Figure 5-3.Steps in the conversion of a
decimal fraction to shortened form.
true of whole numbers. Thus, 0.3, 0.30, and
0.300 are equal but 3, 30, and 300 are not equal.
Also notice that zeros directly after the deci-
mal point do change values. Thus 0.3 is not
equal to either 0.03 or 0.003.
Decimals such as 0.125 are frequently seen.
Although the 0 on the left of the decimal point
is not required, it is often helpful. This is par-
ticularlytrue in an expression such as 32 0.1.
In this expression, the lower dot of the division
symbol must not be crowded against the decimal
point; the 0 serves as an effective spacer. If
any doubt exists concerning the clarity of an
expression such as .125, it should be written as
0.125.
MATHEMATICS. VOLUME 1
0.200
0.025
0.002
0.227
Figure 6-1.(A) Parts of a micrometer;
(B) micrometer scales.
of an inch. Multiplying times 0.025 inch, we
find that each marking on the thimble repre-
sents 0.001 inch.
0.025 inch since
1
is equal to 0.025. The
40
sleeve has 40 markings to the inch. Thus each
space between the markings on the sleeve is
also 0.025 inch. Since 4 such spaces are 0.1
inch (that is, 4 x 0.025), every fourth mark is
labeled in tenths of an inch for convenience in
reading. Thus, 4 marks equal 0.1 inch, 8 marks
equal 0.2 inch, 12 marks equal 0.3 inch, etc.
To enable measurement of a partial turn,
the beveled edge of the thimble is divided into
25 equal parts. Thus each marking on the
thimble is
1
of a complete turn, or
1
of
1
25 25 40
1
25
READING THE MICROMETER
It is sometimes convenient when learning to
read a micrometer to writedown the component
62
parts of the measurement as read on the scales
and then to add them. For example, in figure
6-1 (B) there are two major divisions visible
(0.2 inch). One minor division is showing
clearly (0.025 inch). The marking on the thimble
nearest the horizontal or index line of the sleeve
is the second marking (0.002 inch). Adding
these parts, we have
Thus, the reading is 0.227 inch. As explained
previously, this is read verbally as "two hun-
dred twenty-seven thousandths." A more skill-
ful method of reading the scales is to read all
digits as thousandths directly and to do any
adding mentally. Thus, we read the major divi-
sion on the scale as two hundred thousandths
and the minor division is added on mentally.
The mental process for the above setting then
would be two hundred twenty-five; two hundred
twenty-seven thousandths.
Practice problems:
1. Read each of the micrometer settings shown
in figure 6-2.
Figure 6-2.Micrometer settings.
MATHEMATICS, VOLUME 1
The foregoing example could be followed
through for any distance between markings.
Suppose the 0 mark fell seven tenths of the dis-
tance between ruler markings. It would take
seven vernier markings, a loss of one-hundredth
of an inch each time, to bring the marks in line
at 7 on the vernier.
The vernier principle may be used to get
fine linear readings, angular readings, etc.
The principle is always the same. The vernier
has one more marking than the number of mark-
ings on an equal space of the conventional scale
of the measuring instrument. For example, the
vernier caliper (fig. 6-5) has 25 markings on
the vernier for 24 on the caliper scale. The
caliper is marked off to read to fortieths (0.025)
of an inch, and the vernier extends the accuracy
to a thousandth of an inch.
0.3000
0.0750
0.0080
0.0004
0.3834
Figure 6-5.A vernier caliper.
Vernier Micrometer
By adding a vernier to the micrometer, it is
possible to read accurately to one ten-thousandth
of an inch. The vernier markings are on the
sleeve of the micrometer and are parallel to
the thimble markings. There are 10 divisions
on the vernier that occupy the same space as 9
divisions on the thimble. Since a thimble space
is one thousandth of an inch, a vernier space is
1
of
9
inch, or
9
inch. It is
1
inch
10 1000 10000 10000
less than a thimble space. Thus, as in the pre-
ceding explanation of verniers, it is possible to
read the nearest ten-thousandth of an inch by
reading the vernier digit whose marking coin-
cides with a thimble marking.
In figure 6-6 (A), the last major division
showing fully on the sleeve index is 3. The
third minor division is the last mark clearly
64
showing (0.075). The thimble division nearest
and below the index is the 8 (0.008). The ver-
nier marking that matches a thimble marking
is the fourth (0.0004). Adding them all together,
we have,
The reading is 0.3834 inch. With practice these
readings can be made directly from the microm-
eter, without writing the partial readings.
Figure 6-6.Vernier micrometer settings.
Practice problems:
1. Read the micrometer settings in figure 6-6.
Answers:
1. (A) See the foregoing example.
(B) 0.1539 (E) 0.4690
(C) 0.2507 (F) 0.0552
(D) 0.2500
Assignment Questions
Information: The text pages that you are to study are
provided at the beginning of the assignment questions.
1-64. The product, i n si mpl i f i ed f or m, of t he
mul ti pl i cati on, probl em; 4 (2 hours
22 minutes 32 seconds) is
1. 8 hours 88 minutes 128 seconds
2. 8 hours 90 minutes 8 seconds
3. 9 hours 28 minutes 8 seconds
4. 9 hours 30 minutes 8 seconds
1-65. The product of 12 miles and 13 miles is
1. 156 miles
2. mi l es
3. 156 miles square
4. 156
1-66. The product of 2 feet 8 inches times
3 feet 4 inches may be found by
1. mul t i pl yi ng 2-f eet t i mes 3 f eet t hen
mul ti pl yi ng 8 i nches ti mes 4 i nches
2. mul ti pl yi ng 3 feet ti mes 2 feet 8
i nches then mul ti pl yi ng 4 i nches ti mes
2 feet 8 inches
3. converti ng 2 feet 8 i nches to 2 feet
2
3
and 3 feet 4 inches to 3
t hen mul t i pl yi ng
1
f eet and
3
4. changing 2 feet 8 inches to 3 feet and
3 feet 4 inches to 4 feet and then
mul t i pl yi ng
1-67. If a pi pe 22 feet 6 i nches l ong i s cut i nto
3 equal lengths, how long are the pieces?
(Neglect the width of the saw cuts.)
1. 7 feet 1 inch
2. 7 feet 3 inches
3. 7 feet 4 inches
4. 7 feet 6 inches
1-68. The result of dividing 23 hours 31 minutes
20 seconds by 5 is
1. 43 hours 6 minutes 4 seconds
1
5
2. 4 hours 0 minutes 4224 seconds
3. 4 hours 42 minutes 16 seconds
4. 4 hours 6 minutes 4 seconds
1-69. In whi ch of the fol l owi ng seri es of
operati ons i s the order i n whi ch the
operations are performed important?
l . 2 + 3 + 5
2. ( 3) ( 9) ( 7)
3. 6 x 8 x 9
4. 48 6 x 3
1-70. The answer to the problem 24 4 3 2
i s
1. not defi ned
2. 1
3. 4
4. 9
1-71. The order of operati ons i s i mportant i f
di vi si on or mul t i pl i cat i on i s i nvol ved
wi th other operati ons, Use the rules
pertai ni ng to a seri es of mi xed operati ons
t o cal cul at e t he val ue of 6 x 4 + 8 2.
1. 16
2. 28
3. 36
4. 48
1-72. The number 36 is a multiple of
1, 2, 3, 4, 6, 9, 18, 36, and
1. 10
2. 11
3. 12
4. 13
1-73. An odd number when divided by 2 produces
a remainder of 1.
1-74. The number 7 is a factor of
l . 11
2. 17
3. 24
4. 35
1-75. What i s the val ue of x i f x = (3)(0)(4)(6)?
l . 0
2. 18
3. 24
4. 72
11
Assignment 7
Fundamentals of Algebra; Factoring Polynomials
Textbook Assignment: Chapters 9, 10 (111-117)
7-1. The literal numbers a, x, and p are more
general than the numbers 9, 8, and 7.
7-2. The commutati ve l aw for addi ti on i s i l -
l ustrated by the equati on
1. ab = ba
2. a + a = b + b
3. a + b = b + a
4. a(b + c) = ab + ac
7-3. The associ at i ve l aw of mul t i pl i cat i on i s
i l l ust rat ed by t he equat i on
1. abc = acb = cba
2. a x (b + c) = c x (b + a)
3. a (b + c + d) = ab + ac + ad
4. a (bc) = abc = (ab)c
7-4. If a = 2, b = -3, and c = 4, the algebraic
sum of a - b - c equals
1. - 5
2. 1
3. 3
4. 9
7-5. If r = 1, s = 3, t = 12, and x = 15, what
i s the val ue of the expressi on
2r x
? t -
s
1. - 3 3. 2
2. - 2 4. 3
7-6. The al gebrai c expressi on
is considered to be three numbers.
7-7. What i s the val ue of the al gebrai c ex-
pression
5x
2
- 2xy + (3x)
2
when x = 2 and y = -3?
1. 44
2. 68
3. 124
4. 148
7-8. What name is given to the algebraic ex-
pressi on ax - 2bx + cx
2
- 4?
1. Monomial
2. Bi nomi al
3. Tr i nomi al
4. Pol ynomi al
7-9. Which statement is true regarding the
monomial 17xyz?
1. 17 i s t he coef f i ci ent of xyz.
2. 17x i s t he coef f i ci ent of yz.
3. 17xy i s t he coef f i ci ent of z.
4. Each of the above is a true statement.
7-10. In the expressi on xy, what i s the co-
ef f i ci ent of xy?
1. 1
2. x
3. y
4. x y
7- 11. What i s t he coef f i ci ent of x
2
y i n t he
expressi on x
2
y - ab?
1. 1
2. 2
3. x
2
4. y
7- 12. Two terms of an expression are said to be
l i ke i f t hey cont ai n
1. at least one factor in common
2. the same numeri cal coeffi ci ent
3. t he same l i t eral f act ors wi t h onl y
t hei r exponent s di f f er ent
4. t he same l i t eral f act ors rai sed t o t he
same powers
7- 13. The like terms in the expression
2 ac
2
- 2bc
2
+ ac
2
- 2c
2
are
1. 2ac
2
and 2bc
2
2. 2ac
2
and ac
2
3. 2ac
2
and 2c
2
4. 2bc
2
and 2c
2
40