8-Bit Microcontroller With 2K Bytes Flash AT89C2051: Features
8-Bit Microcontroller With 2K Bytes Flash AT89C2051: Features
8-Bit Microcontroller With 2K Bytes Flash AT89C2051: Features
Pin Configuration
PDIP/SOIC
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
RST/VPP
(RXD) P3.0
(TXD) P3.1
XTAL2
XTAL1
(INT0) P3.2
(INT1) P3.3
(TO) P3.4
(T1) P3.5
GND
VCC
P1.7
P1.6
P1.5
P1.4
P1.3
P1.2
P1.1 (AIN1)
P1.0 (AIN0)
P3.7
Features
Compatible with MCS-51
Products
2K Bytes of Reprogrammable Flash Memory
Endurance: 1,000 Write/Erase Cycles
2.7V to 6V Operating Range
Fully Static Operation: 0 Hz to 24 MHz
Two-level Program Memory Lock
128 x 8-bit Internal RAM
15 Programmable I/O Lines
Two 16-bit Timer/Counters
Six Interrupt Sources
Programmable Serial UART Channel
Direct LED Drive Outputs
On-chip Analog Comparator
Low-power Idle and Power-down Modes
Description
The AT89C2051 is a low-voltage, high-performance CMOS 8-bit microcomputer with
2K bytes of Flash programmable and erasable read only memory (PEROM). The
device is manufactured using Atmels high-density nonvolatile memory technology
and is compatible with the industry-standard MCS-51 instruction set. By combining a
versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89C2051 is a power-
ful microcomputer which provides a highly-flexible and cost-effective solution to many
embedded control applications.
The AT89C2051 provides the following standard features: 2K bytes of Flash, 128
bytes of RAM, 15 I/O lines, two 16-bit timer/counters, a five vector two-level interrupt
architecture, a full duplex serial port, a precision analog comparator, on-chip oscillator
and clock circuitry. In addition, the AT89C2051 is designed with static logic for opera-
tion down to zero frequency and supports two software selectable power saving
modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial
port and interrupt system to continue functioning. The power-down mode saves the
RAM contents but freezes the oscillator disabling all other chip functions until the next
hardware reset.
Rev. 0368E02/00
8-bit
Microcontroller
with 2K Bytes
Flash
AT89C2051
AT89C2051 2
Block Diagram
AT89C2051
3
Pin Description
VCC
Supply voltage.
GND
Ground.
Port 1
Port 1 is an 8-bit bi-irectional I/O port. Port pins P1.2 to
P1.7 provide internal pullups. P1.0 and P1.1 require exter-
nal pullups. P1.0 and P1.1 also serve as the positive input
(AIN0) and the negative input (AIN1), respectively, of the
on-chip precision analog comparator. The Port 1 output
buffers can sink 20 mA and can drive LED displays directly.
When 1s are written to Port 1 pins, they can be used as
inputs. When pins P1.2 to P1.7 are used as inputs and are
externally pulled low, they will source current (I
IL
) because
of the internal pullups.
Port 1 also receives code data during Flash programming
and verification.
Port 3
Port 3 pins P3.0 to P3.5, P3.7 are seven bi-irectional I/O
pins with internal pullups. P3.6 is hard-wired as an input to
the output of the on-chip comparator and is not accessible
as a general purpose I/O pin. The Port 3 output buffers can
sink 20 mA. When 1s are written to Port 3 pins they are
pulled high by the internal pullups and can be used as
inputs. As inputs, Port 3 pins that are externally being
pulled low will source current (I
IL
) because of the pullups.
Port 3 also serves the functions of various special features
of the AT89C2051 as listed below:
Port 3 also receives some control signals for Flash pro-
gramming and verification.
RST
Reset input. All I/O pins are reset to 1s as soon as RST
goes high. Holding the RST pin high for two machine
cycles while the oscillator is running resets the device.
Each machine cycle takes 12 oscillator or clock cycles.
XTAL1
Input to the inverting oscillator amplifier and input to the
internal clock operating circuit.
XTAL2
Output from the inverting oscillator amplifier.
Oscillator Characteristics
XTAL1 and XTAL2 are the input and output, respectively,
of an inverting amplifier which can be configured for use as
an on-chip oscillator, as shown in Figure 1. Either a quartz
crystal or ceramic resonator may be used. To drive the
device from an external clock source, XTAL2 should be left
unconnected while XTAL1 is driven as shown in Figure 2.
There are no requirements on the duty cycle of the external
clock signal, since the input to the internal clocking circuitry
is through a divide-by-two flip-flop, but minimum and maxi-
mum voltage high and low time specifications must be
observed.
Figure 1. Oscillator Connections
Note: C1, C2 = 30 pF 10 pF for Crystals
= 40 pF 10 pF for Ceramic Resonators
Figure 2. External Clock Drive Configuration
Port Pin Alternate Functions
P3.0 RXD (serial input port)
P3.1 TXD (serial output port)
P3.2 INT0 (external interrupt 0)
P3.3 INT1 (external interrupt 1)
P3.4 T0 (timer 0 external input)
P3.5 T1 (timer 1 external input)
AT89C2051 4
Special Function Registers
A map of the on-chip memory area called the Special Func-
tion Register (SFR) space is shown in the table below.
Note that not all of the addresses are occupied, and unoc-
cupied addresses may not be implemented on the chip.
Read accesses to these addresses will in general return
random data, and write accesses will have an indetermi-
nate effect.
User software should not write 1s to these unlisted loca-
tions, since they may be used in future products to invoke
new features. In that case, the reset or inactive values of
the new bits will always be 0.
Table 1. AT89C2051 SFR Map and Reset Values
0F8H 0FFH
0F0H B
00000000
0F7H
0E8H 0EFH
0E0H ACC
00000000
0E7H
0D8H 0DFH
0D0H PSW
00000000
0D7H
0C8H 0CFH
0C0H 0C7H
0B8H IP
XXX00000
0BFH
0B0H P3
11111111
0B7H
0A8H IE
0XX00000
0AFH
0A0H 0A7H
98H SCON
00000000
SBUF
XXXXXXXX
9FH
90H P1
11111111
97H
88H TCON
00000000
TMOD
00000000
TL0
00000000
TL1
00000000
TH0
00000000
TH1
00000000
8FH
80H SP
00000111
DPL
00000000
DPH
00000000
PCON
0XXX0000
87H
AT89C2051
5
Restrictions on Certain Instructions
The AT89C2051 and is an economical and cost-effective
member of Atmels growing family of microcontrollers. It
contains 2K bytes of flash program memory. It is fully com-
pat i bl e wi t h t he MCS-51 archi t ect ur e, and can be
programmed using the MCS-51 instruction set. However,
there are a few considerations one must keep in mind
when utilizing certain instructions to program this device.
All the instructions related to jumping or branching should
be restricted such that the destination address falls within
the physical program memory space of the device, which is
2K for the AT89C2051. This should be the responsibility of
the software programmer. For example, LJMP 7E0H
would be a valid instruction for the AT89C2051 (with 2K of
memory), whereas LJMP 900H would not.
1. Branching instructions:
LCALL, LJMP, ACALL, AJMP, SJMP, JMP @A+DPTR
These unconditional branching instructions will execute
correctly as long as the programmer keeps in mind that the
destination branching address must fall within the physical
boundaries of the program memory size (locations 00H to
7FFH for the 89C2051). Violating the physical space limits
may cause unknown program behavior.
CJNE [...], DJNZ [...], JB, JNB, JC, JNC, JBC, JZ, JNZ With
these conditional branching instructions the same rule
above applies. Again, violating the memory boundaries
may cause erratic execution.
For applications involving interrupts the normal interrupt
service routine address locations of the 80C51 family archi-
tecture have been preserved.
2. MOVX-related instructions, Data Memory:
The AT89C2051 contains 128 bytes of internal data mem-
ory. Thus, in the AT89C2051 the stack depth is limited to
128 bytes, the amount of available RAM. External DATA
memory access is not supported in this device, nor is exter-
nal PROGRAM memory execution. Therefore, no MOVX
[...] instructions should be included in the program.
A typical 80C51 assembler will still assemble instructions,
even if they are written in violation of the restrictions men-
tioned above. It is the responsibility of the controller user to
know the physical features and limitations of the device
bei ng used and adj ust t he i nst r uct i ons used
correspondingly.
Program Memory Lock Bits
On the chip are two lock bits which can be left unpro-
grammed (U) or can be programmed (P) to obtain the
additional features listed in the table below:
Lock Bit Protection Modes
(1)
Note: 1. The Lock Bits can only be erased with the Chip Erase
operation.
Idle Mode
In idle mode, the CPU puts itself to sleep while all the on-
chip peripherals remain active. The mode is invoked by
software. The content of the on-chip RAM and all the spe-
cial functions registers remain unchanged during this
mode. The idle mode can be terminated by any enabled
interrupt or by a hardware reset.
P1.0 and P1.1 should be set to 0 if no external pullups are
used, or set to 1 if external pullups are used.
It should be noted that when idle is terminated by a hard-
ware reset , t he devi ce normal l y resumes program
execution, from where it left off, up to two machine cycles
before the internal reset algorithm takes control. On-chip
hardware inhibits access to internal RAM in this event, but
access to the port pins is not inhibited. To eliminate the
possibility of an unexpected write to a port pin when Idle is
terminated by reset, the instruction following the one that
invokes Idle should not be one that writes to a port pin or to
external memory.
Power-down Mode
In the power down mode the oscillator is stopped, and the
instruction that invokes power down is the last instruction
executed. The on-chip RAM and Special Function Regis-
ters retain their values until the power down mode is
terminated. The only exit from power down is a hardware
reset. Reset redefines the SFRs but does not change the
on-chip RAM. The reset should not be activated before V
CC
is restored to its normal operating level and must be held
active long enough to allow the oscillator to restart and
stabilize.
P1.0 and P1.1 should be set to 0 if no external pullups are
used, or set to 1 if external pullups are used.
Program Lock Bits
LB1 LB2 Protection Type
1 U U No program lock features.
2 P U Further programming of the Flash
is disabled.
3 P P Same as mode 2, also verify is
disabled.
AT89C2051 6
Programming The Flash
The AT89C2051 is shipped with the 2K bytes of on-chip
PEROM code memory array in the erased state (i.e., con-
tents = FFH) and ready to be programmed. The code
memory array is programmed one byte at a time. Once the
array is programmed, to re-program any non-blank byte,
the entire memory array needs to be erased electrically.
Internal Address Counter: The AT89C2051 contains an
internal PEROM address counter which is always reset to
000H on the rising edge of RST and is advanced by apply-
ing a positive going pulse to pin XTAL1.
Programming Algorithm: To program the AT89C2051,
the following sequence is recommended.
1. Power-up sequence:
Apply power between V
CC
and GND pins
Set RST and XTAL1 to GND
2. Set pin RST to H
Set pin P3.2 to H
3. Apply the appropriate combination of H or L logic
levels to pins P3.3, P3.4, P3.5, P3.7 to select one of the
programming operations shown in the PEROM Pro-
gramming Modes table.
To Program and Verify the Array:
4. Apply data for Code byte at location 000H to P1.0 to
P1.7.
5. Raise RST to 12V to enable programming.
6. Pulse P3.2 once to program a byte in the PEROM array
or the lock bits. The byte-write cycle is self-timed and
typically takes 1.2 ms.
7. To verify the programmed data, lower RST from 12V to
logic H level and set pins P3.3 to P3.7 to the appropiate
levels. Output data can be read at the port P1 pins.
8. To program a byte at the next address location, pulse
XTAL1 pin once to advance the internal address
counter. Apply new data to the port P1 pins.
9. Repeat steps 5 through 8, changing data and advancing
the address counter for the entire 2K bytes array or until
the end of the object file is reached.
10.Power-off sequence:
set XTAL1 to L
set RST to L
Turn V
CC
power off
Data Polling: The AT89C2051 features Data Polling to
indicate the end of a write cycle. During a write cycle, an
attempted read of the last byte written will result in the com-
plement of the written data on P1.7. Once the write cycle
has been completed, true data is valid on all outputs, and
the next cycle may begin. Data Polling may begin any time
after a write cycle has been initiated.
Ready/Busy: The Progress of byte programming can also
be monitored by the RDY/BSY output signal. Pin P3.1 is
pulled low after P3.2 goes High during programming to indi-
cate BUSY. P3.1 is pulled High again when programming is
done to indicate READY.
Program Verify: If lock bits LB1 and LB2 have not been
programmed code data can be read back via the data lines
for verification:
1. Reset the internal address counter to 000H by bringing
RST from L to H.
2. Apply the appropriate control signals for Read Code data
and read the output data at the port P1 pins.
3. Pulse pin XTAL1 once to advance the internal address
counter.
4. Read the next code data byte at the port P1 pins.
5. Repeat steps 3 and 4 until the entire array is read.
The lock bits cannot be verified directly. Verification of the
lock bits is achieved by observing that their features are
enabled.
Chip Erase: The entire PEROM array (2K bytes) and the
two Lock Bits are erased electrically by using the proper
combination of control signals and by holding P3.2 low for
10 ms. The code array is written with all 1s in the Chip
Erase operation and must be executed before any non-
blank memory byte can be re-programmed.
Reading the Signature Bytes: The signature bytes are
read by the same procedure as a normal verification of
locations 000H, 001H, and 002H, except that P3.5 and
P3.7 must be pulled to a logic low. The values returned are
as follows.
(000H) = 1EH indicates manufactured by Atmel
(001H) = 21H indicates 89C2051
Programming Interface
Every code byte in the Flash array can be written and the
entire array can be erased by using the appropriate combi-
nation of control signals. The write operation cycle is self-
timed and once initiated, will automatically time itself to
completion.
All major programming vendors offer worldwide support for
the Atmel microcontroller series. Please contact your local
programming vendor for the appropriate software revision.
AT89C2051
7
Notes: 1. The internal PEROM address counter is reset to 000H on the rising edge of RST and is advanced by a positive pulse at
XTAL 1 pin.
2. Chip Erase requires a 10 ms PROG pulse.
3. P3.1 is pulled Low during programming to indicate RDY/BSY.
Figure 3. Programming the Flash Memory Figure 4. Verifying the Flash Memory
Flash Programming Modes
Mode RST/VPP P3.2/PROG P3.3 P3.4 P3.5 P3.7
Write Code Data
(1)(3)
12V L H H H
Read Code Data
(1)
H H L L H H
Write Lock Bit - 1 12V H H H H
Bit - 2 12V H H L L
Chip Erase 12V H L L L
Read Signature Byte H H L L L L
(2)
PP
AT89C2051 8
Note: 1. Only used in 12-volt programming mode.
Flash Programming and Verification Waveforms
Flash Programming and Verification Characteristics
T
A
= 0C to 70C, V
CC
= 5.0 10%
Symbol Parameter Min Max Units
V
PP
Programming Enable Voltage 11.5 12.5 V
I
PP
Programming Enable Current 250 A
t
DVGL
Data Setup to PROG Low 1.0 s
t
GHDX
Data Hold after PROG 1.0 s
t
EHSH
P3.4 (ENABLE) High to V
PP
1.0 s
t
SHGL
V
PP
Setup to PROG Low 10 s
t
GHSL
V
PP
Hold after PROG 10 s
t
GLGH
PROG Width 1 110 s
t
ELQV
ENABLE Low to Data Valid 1.0 s
t
EHQZ
Data Float after ENABLE 0 1.0 s
t
GHBL
PROG High to BUSY Low 50 ns
t
WC
Byte Write Cycle Time 2.0 ms
t
BHIH
RDY/BSY\ to Increment Clock Delay 1.0 s
t
IHIL
Increment Clock High 200 ns
AT89C2051
9
Notes: 1. Under steady state (non-transient) conditions, I
OL
must be externally limited as follows:
Maximum I
OL
per port pin: 20 mA
Maximum total I
OL
for all output pins: 80 mA
If I
OL
exceeds the test condition, V
OL
may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test conditions.
2. Minimum V
CC
for Power-down is 2V.
Absolute Maximum Ratings*
Operating Temperature ................................. -55C to +125C
*NOTICE: Stresses beyond those listed under Absolute
Maximum Ratings may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Storage Temperature..................................... -65C to +150C
Voltage on Any Pin
with Respect to Ground.....................................-1.0V to +7.0V
Maximum Operating Voltage ............................................ 6.6V
DC Output Current...................................................... 25.0 mA
DC Characteristics
T
A
= -40C to 85C, V
CC
= 2.0V to 6.0V (unless otherwise noted)
Symbol Parameter Condition Min Max Units
V
IL
Input Low-voltage -0.5 0.2 V
CC
- 0.1 V
V
IH
Input High-voltage (Except XTAL1, RST) 0.2 V
CC
+ 0.9 V
CC
+ 0.5 V
V
IH1
Input High-voltage (XTAL1, RST) 0.7 V
CC
V
CC
+ 0.5 V
V
OL
Output Low-voltage
(1)
(Ports 1, 3)
I
OL
= 20 mA, V
CC
= 5V
I
OL
= 10 mA, V
CC
= 2.7V
0.5 V
V
OH
Output High-voltage
(Ports 1, 3)
I
OH
= -80 A, V
CC
= 5V 10% 2.4 V
I
OH
= -30 A 0.75 V
CC
V
I
OH
= -12 A 0.9 V
CC
V
I
IL
Logical 0 Input Current
(Ports 1, 3)
V
IN
= 0.45V -50 A
I
TL
Logical 1 to 0 Transition Current
(Ports 1, 3)
V
IN
= 2V, V
CC
= 5V 10% -750 A
I
LI
Input Leakage Current
(Port P1.0, P1.1)
0 < V
IN
< V
CC
10 A
V
OS
Comparator Input Offset Voltage V
CC
= 5V 20 mV
V
CM
Comparator Input Common
Mode Voltage
0 V
CC
V
RRST Reset Pull-down Resistor 50 300 K
C
IO
Pin Capacitance Test Freq. = 1 MHz, T
A
= 25C 10 pF
I
CC
Power Supply Current Active Mode, 12 MHz, V
CC
= 6V/3V 15/5.5 mA
Idle Mode, 12 MHz, V
CC
= 6V/3V
P1.0 & P1.1 = 0V or V
CC
5/1 mA
Power-down Mode
(2)
V
CC
= 6V P1.0 & P1.1 = 0V or V
CC
100 A
V
CC
= 3V P1.0 & P1.1 = 0V or V
CC
20 A
AT89C2051 10
External Clock Drive Waveforms
External Clock Drive
Symbol Parameter
V
CC
= 2.7V to 6.0V V
CC
= 4.0V to 6.0V
Units Min Max Min Max
1/t
CLCL
Oscillator Frequency 0 12 0 24 MHz
t
CLCL
Clock Period 83.3 41.6 ns
t
CHCX
High Time 30 15 ns
t
CLCX
Low Time 30 15 ns
t
CLCH
Rise Time 20 20 ns
t
CHCL
Fall Time 20 20 ns
AT89C2051
11
()
Shift Register Mode Timing Waveforms
AC Testing Input/Output Waveforms
(1)
Note: 1. AC Inputs during testing are driven at V
CC
- 0.5V for a
logic 1 and 0.45V for a logic 0. Timing measurements
are made at V
IH
min. for a logic 1 and V
IL
max. for a
logic 0.
Float Waveforms
(1)
Note: 1. For timing purposes, a port pin is no longer floating
when a 100 mV change from load voltage occurs. A
port pin begins to float when 100 mV change frothe
loaded V
OH
/V
OL
level occurs.
Serial Port Timing: Shift Register Mode Test Conditions
V
CC
= 5.0V 20%; Load Capacitance = 80 pF
Symbol Parameter
12 MHz Osc Variable Oscillator
Units Min Max Min Max
t
XLXL
Serial Port Clock Cycle Time 1.0 12t
CLCL
s
t
QVXH
Output Data Setup to Clock Rising Edge 700 10t
CLCL
-133 ns
t
XHQX
Output Data Hold after Clock Rising Edge 50 2t
CLCL
-117 ns
t
XHDX
Input Data Hold after Clock Rising Edge 0 0 ns
t
XHDV
Clock Rising Edge to Input Data Valid 700 10t
CLCL
-133 ns
AT89C2051 12
AT89C2051
TYPICAL ICC - ACTIVE(85C)
0
5
10
15
20
0 6 12 18 24
FREQUENCY (MHz)
I
C
C
m
A
Vcc=6.0V
Vcc=5.0V
Vcc=3.0V
AT89C2051
TYPICAL ICC - IDLE (85C)
0
1
2
3
0 3 6 9 12
FREQUENCY (MHz)
I
C
C
m
A
Vcc=6.0V
Vcc=5.0V
Vcc=3.0V
AT89C2051
TYPICAL ICC vs. VOLTAGE- POWER DOWN (85C)
0
5
10
15
20
3.0V 4.0V 5.0V 6.0V
Vcc VOLTAGE
I
C
C
A
Notes: 1. XTAL1 tied to GND for I
CC
(power-down)
2. P.1.0 and P1.1 = V
CC
or GND
3. Lock bits programmed
AT89C2051
13
Ordering Information
Speed
(MHz)
Power
Supply Ordering Code Package Operation Range
12 2.7V to 6.0V AT89C2051-12PC
AT89C2051-12SC
20P3
20S
Commercial
(0C to 70C)
AT89C2051-12PI
AT89C2051-12SI
20P3
20S
Industrial
(-40C to 85C)
24 4.0V to 6.0V AT89C2051-24PC
AT89C2051-24SC
20P3
20S
Commercial
(0C to 70C)
AT89C2051-24PI
AT89C2051-24SI
20P3
20S
Industrial
(-40C to 85C)
Package Type
20P3 20-lead, 0.300 Wide, Plastic Dual In-line Package (PDIP)
20S 20-lead, 0.300 Wide, Plastic Gull Wing Small Outline (SOIC)
AT89C2051 14
Packaging Information
1.060(26.9)
.980(24.9)
PIN
1
.280(7.11)
.240(6.10)
.090(2.29)
MAX
.005(.127)
MIN
.015(.381) MIN
.022(.559)
.014(.356)
.070(1.78)
.045(1.13)
.325(8.26)
.300(7.62)
0
15
REF
.430(10.92) MAX
.014(.356)
.008(.203)
.110(2.79)
.090(2.29)
.150(3.81)
.115(2.92)
SEATING
PLANE
.210(5.33)
MAX
.900(22.86) REF
0.299 (7.60)
0.291 (7.39)
0.020 (0.508)
0.013 (0.330)
0.420 (10.7)
0.393 (9.98)
PIN 1
.050 (1.27) BSC
0.513 (13.0)
0.497 (12.6)
0.012 (0.305)
0.003 (0.076)
0.105 (2.67)
0.092 (2.34)
0
8
REF
0.035 (0.889)
0.015 (0.381)
0.013 (0.330)
0.009 (0.229)
20P3, 20-lead, 0.300" Wide, Plastic Dual Inline
Package (PDIP)
Dimensions in Inches and (Millimeters)
JEDEC STANDARD MS-001 AD
20S, 20-lead, 0.300" Wide, Plastic Gull WIng Small
Outline (SOIC)
Dimensions in Inches and (Millimeters)
Atmel Corporation 2000.
Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Companys standard war-
ranty which is detailed in Atmels Terms and Conditions located on the Companys web site. The Company assumes no responsibility for
any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without
notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual prop-
erty of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmels products are
not authorized for use as critical components in life suppor t devices or systems.
Atmel Headquarters Atmel Operations
Corporate Headquarters
2325 Orchard Parkway
San Jose, CA 95131
TEL (408) 441-0311
FAX (408) 487-2600
Europe
Atmel U.K., Ltd.
Coliseum Business Centre
Riverside Way
Camberley, Surrey GU15 3YL
England
TEL (44) 1276-686-677
FAX (44) 1276-686-697
Asia
Atmel Asia, Ltd.
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimhatsui
East Kowloon
Hong Kong
TEL (852) 2721-9778
FAX (852) 2722-1369
Japan
Atmel Japan K.K.
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
TEL (81) 3-3523-3551
FAX (81) 3-3523-7581
Atmel Colorado Springs
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TEL (719) 576-3300
FAX (719) 540-1759
Atmel Rousset
Zone Industrielle
13106 Rousset Cedex
France
TEL (33) 4-4253-6000
FAX (33) 4-4253-6001
Fax-on-Demand
North America:
1-(800) 292-8635
International:
1-(408) 441-0732
e-mail
literature@atmel.com
Web Site
http://www.atmel.com
BBS
1-(408) 436-4309
Printed on recycled paper.
0368E02/00/xM
Marks bearing
and/or