Scribd Logo
Upload

Welcome to Scribd!

  • 120 views

    85001-0548 - Optical Beam Smoke Detector

    Uploaded by

    pkgoyal1983
    The document provides details about the Fireray 2000 optical beam smoke detector, including its components, features, specifications, applications, wiring, and ordering information. It functions by transmitting an infrared light beam between a transmitter and receiver head, and detects smoke by a reduction in the light signal. When the signal is reduced by a certain amount for over 8-10 seconds, the fire alarm is activated. It is suitable for use in large spaces like warehouses and factories.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    85001-0548 - Optical Beam Smoke Detector

    Uploaded by

    pkgoyal1983
    120 views4 pages
    The document provides details about the Fireray 2000 optical beam smoke detector, including its components, features, specifications, applications, wiring, and ordering information. It functions by transmitting an infrared light beam between a transmitter and receiver head, and detects smoke by a reduction in the light signal. When the signal is reduced by a certain amount for over 8-10 seconds, the fire alarm is activated. It is suitable for use in large spaces like warehouses and factories.

    Original Description:

    beam detector

    Original Title

    85001-0548 -- Optical Beam Smoke Detector

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides details about the Fireray 2000 optical beam smoke detector, including its components, features, specifications, applications, wiring, and ordering information. It functions by transmitting an infrared light beam between a transmitter and receiver head, and detects smoke by a reduction in the light signal. When the signal is reduced by a certain amount for over 8-10 seconds, the fire alarm is activated. It is suitable for use in large spaces like warehouses and factories.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    120 views4 pages

    85001-0548 - Optical Beam Smoke Detector

    Uploaded by

    pkgoyal1983
    The document provides details about the Fireray 2000 optical beam smoke detector, including its components, features, specifications, applications, wiring, and ordering information. It functions by transmitting an infrared light beam between a transmitter and receiver head, and detects smoke by a reduction in the light signal. When the signal is reduced by a certain amount for over 8-10 seconds, the fire alarm is activated. It is suitable for use in large spaces like warehouses and factories.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    Page 1 of 4 D A T A S H E E T 85001-0548

    Not to be used for installation purposes. Issue 5


    EST Catalog u Conventional Initiating
    0
    6
    -
    2
    1
    -
    1
    0
    Overview
    The Fireray 2000 is a projected beam smoke detector designed to
    detect smoke in a large volume. The system is comprised of three
    pieces, a transmitter head, a receiver head, and a control box.
    The transmitter projects a modulated infrared light beam to the
    receiver. At the receiver, the signal is sent to the controller, where
    it is analyzed. If there is smoke in the beam path, the receivers
    signal is reduced by a level proportional to the density of the
    smoke. When the signal strength is reduced to a level between the
    obscuration threshold and 93% for more than 8 to 10 seconds,
    the re alarm output relay is activated. The alarm obscuration
    threshold may be set at 25%, 35% or 50% obscuration, depend-
    ing on the application. Reduction in signal strength below 93% is
    indicated as a fault condition.
    The controller is designed to mount near ground level where it is
    convenient for maintenance. The controller is powered by the re
    alarm control panel (FACP) and returns both alarm and trouble
    signals to the FACP via relay contacts. The controller features
    an automatic gain control that automatically compensates for
    component aging, and dirt on the optical surfaces. The optional
    installation aid is used to quickly align the beam and a test card is
    supplied with each controller to perform functional tests.
    Standard Features
    Coverage up to 330 ft (100m) x 50 ft (15.24m) - 16,000 ft
    (1,524 m)
    Use with prism reectors
    Supervised
    Automatic gain control
    Alarm and trouble contacts
    Controls located at convenient level
    Wide beam angle simplies alignment and provides stability
    Low current consumption
    MEA
    Optical Beam
    Smoke Detector
    FIRERAY 2000
    Page 2 of 4 D A T A S H E E T 85001-0548
    Not to be used for installation purposes. Issue 5
    Application
    Projected beam smoke detectors are ideal for large volume ap-
    plications such as atria, warehouses, factories, churches, power
    stations, and industrial plants. Detection time depends on a
    number of factors including the location of the detectors within the
    protected area, the volume of smoke produced by the re, roof
    construction and the ventilation arrangements.
    For at ceiling applications, smoke typically makes its way into the
    detection beam from the point on the ceiling directly above the
    re due to air currents and heat layering effects. At the maximum
    range of 330 ft (100m) the diameter of the beam is approximately
    10 ft (3m). For reliable detection, the maximum distance either
    side of the beam axis has been determined to be 25 ft (7.6m). Us-
    ing this spacing yields a maximum total coverage area of 16,500
    square feet (1,524m). Smoke layering is overcome by mounting
    detectors such that the beam is below the heat layer and project-
    ing into the smoke layer. For at ceiling applications the system is
    designed to be mounted approximately 19 inches (482mm) below
    and parallel to the roof or ceiling. Detection time is increased in
    buildings with peaked roofs should a re occur at the fringes of
    the protected area. No more than approximately 10 ft (3m) of the
    beam path should be within 19 in (482mm) of any wall or partition
    and the centerline of the beam.
    When access to the opposite wall is restricted or where wiring is dif-
    cult, the transmitter may be installed adjacent to the receiver. A prism
    is then mounted on a far wall and used to reect the signal from the
    transmitter back to the receiver. When prisms are used, maximum
    beam length is reduced as shown in the specication table.
    Typical Wiring
    Shielded cable recommended for all wiring.
    The control unit must be grounded to the power supply.
    Terminate shields outside the control cabinet at the cable
    clamp. Do NOT let shields enter the cabinet.
    Use metal junction boxes only, no plastic boxes permitted.
    Relay wiring
    as required
    CABLE
    CLAMP
    CABLE
    CLAMP
    CABLE
    CLAMP
    CABLE
    CLAMP
    Remote reset switch
    or relay close momentarily
    to reset
    May be same P.S.U.
    as for control unit
    P.S.U. (24 Vdc)
    TEST
    METER
    EXTERNAL
    RESET
    -VE +VE
    (0V) (24Vdc)
    -VE +VE
    (0V) (24Vdc)
    P.S.U.
    B R
    R +V Rx
    SIGNAL Rx
    0V Rx
    Y
    B
    SIGNAL LEVEL
    LOW HIGH
    TEST/RESET
    ON OFF
    SW5
    TROUBLE LED
    Rx
    Tx
    A
    L
    A
    R
    M
    T
    R
    O
    U
    B
    L
    E
    N/O
    N/C
    COM
    N/O
    N/C
    COM
    100 MA
    ALARM LATCH
    COMP
    25%
    35%
    50%
    +
    +
    -
    -
    S
    U
    P
    P
    L
    Y
    2
    4
    V
    d
    c
    Page 3 of 4 D A T A S H E E T 85001-0548
    Not to be used for installation purposes. Issue 5
    Ordering Information
    Specications
    Controller
    Power Requirements
    Standby
    Alarm
    8.5 mA
    14.5 mA
    Output Relays
    Alarm
    Trouble
    Form C rated 0.5 A @ 30 Vdc
    Form C rated 0.5 A @ 30 Vdc
    LED Indicators Alarm Signal High Signal Low Fault
    Reset Congurable, manual or automatic
    Dimensions (HxWxD) 10.5 in (260 mm) x 8.5 in (210 mm) x 3.5 in (89 mm)
    Weight 5 lb (2.25 kg)
    Operating Environment
    Temperature
    Humidity
    32 F to 100 F (0 C to 38 C)
    93%RH, Non-condensing
    Detector Heads
    Beam
    Width
    Length
    25 ft (7.62 m) either side of transmitter centerline
    33 ft (10 m) to 330 ft (100 m)
    Alarm Threshold 25%, 35%, or 50% obscuration
    Wiring Requirements
    Transmitter
    Receiver
    2 conductor twisted-shielded, 18 AWG (0.75 mm)
    3 conductor twisted-shielded, 18 AWG (0.75 mm), 330 ft (100 m) max.
    Power Requirements
    Transmitter
    Receiver
    5 mA @ 24 Vdc
    Nominal Supplied by controller
    Dimensions (HxWxD) with
    Bracket
    3.75 in (95 mm) x 3.25 in (83 mm) x 4 in (101 mm)
    Weight with Bracket 14 oz (400 g)
    Environment
    Temperature
    Humidity
    32 F to 100 F (0 C to 38 C)
    93%RH, Non-condensing
    Beam Ranges using Prism(s)
    1 Prism
    4 Prisms in a square
    6 Prisms in a rectangle
    6.5 ft (1.98 m) to 82 ft (25 m)
    82 ft (25 m) to 115 ft (35 m)
    115 ft (35 m) to 148 ft (45 m)
    Construction Zinc Alloy housing nished in white enamel
    Prism Dimensions (HxWxD) 4 in (100 mm) x 4 in (100mm) x 5/16 in (9 mm)
    Model Description Ship Wt., lb (kg)
    22310-18-01 Beam Smoke Detector Controller with Heads 8.5 (3.9)
    0201-01-A Beam Alignment Aid 1 (.45)
    23901-00 Prism - Beam Detector 0.3 (.14)
    Page 4 of 4 D A T A S H E E T 85001-0548
    Not to be used for installation purposes. Issue 5
    0
    6
    -
    2
    1
    -
    1
    0
    Detection & alarm since 1872
    U.S.
    T 888-378-2329
    F 866-503-3996
    Canada
    Chubb-Edwards
    T 519 376 2430
    F 519 376 7258
    Southeast Asia
    T : +65 6391 9300
    F : +65 6391 9306

    India
    T : +91 80 4344 2000
    F : +91 80 4344 2050

    Australia
    T +61 3 9239 1200
    F +61 3 9239 1299
    Europe
    T +32 2 725 11 20
    F +32 2 721 86 13
    Latin America
    T 305 593 4301
    F 305 593 4300
    utcreandsecurity.com
    2010 UTC Fire & Security.
    All rights reserved.

    You might also like