Scribd
Upload
113 views4 pages

CASE 8000: Preventive Maintenance Inspection Report

Uploaded by

Brent Sutton
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
113 views4 pages

CASE 8000: Preventive Maintenance Inspection Report

Uploaded by

Brent Sutton
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Template Revision D

CASE 8000 DPMFRM-022


Preventive Maintenance Inspection Report 30 Jun 1999
Page 1 of 4
Customer______________________________ Customer Number______________________ Date___________
FE ___________________________________ FE ID________ Call Number______________________________
Equipment Serial Number ________________ Software Revision _________
Configuration ()
___ 12SL ___ Remote Viewing ___ Full Disclosure
___ Data Storage on File Server
Tools
1. Leakage tester 3. Multimeter 5. ESD Mat and Wrist Strap
2. Standard hand tools 4. Service Manual (p/n 415047-001)
Visual Inspection ()
Inspect the following for excess wear and/or any visual signs of damage.
1. __Coiled patient cable 3.____AC power cord
2. __Patient leadwires 4.____Chassis hardware
Cleaning ()
1. ___ Clean all internals of dust 2. ___ Clean external surfaces
Calibration ()
1. ___ Writer Tests 2. ___ Key Pad Test
Electrical Safety Checks ()
Refer to PM Application Form DPMAPP-001-4 class __ for leakage standards for specific voltages.
1. ___ Wall Receptacle Test
2. ___ Ground Continuity (Impedence of protected connection) Test( .1 or .2 w/power cord)
3. Leakage Open Closed
Normal Reversed Normal Reversed
Ground(Earth) wire leakage to ground test ___ ___ NA NA
Chassis(Enclosure) leakage to ground test ___ ___ ___ ___
Source Risk(Patient cable leakage to ground) Leakage ___ ___ ___ ___
Sink Risk(Patient cable leakage into patient leads) Leakage NA NA ___ ___
Checkout Procedure ()
A.___ Attach ECG simulator, press the RHYTHM key and check the report for proper data, paper tracking and clarity.
B.___ Select a protocol and start treadmill(or ergometer) to verify speed and grade( or workload for ergometers) are operating
properly.
C.___ Depress the Emergency stop button(if installed) while the treadmill(if installed) is running at 3 m.p.h. to verify the
treadmill stops correctly.
D.___ Depress the Treadmill Stop button on the CASE 8000 stress keyboard while the treadmill(if installed) is running at 3
m.p.h. and verify the treadmill stops correctly.
E.___ Perform the Keyboard Test using the Service Screen.
F.___ Perform Writer Diagnostics from the Service Screen.
DPMFRM-022
Page 2 of 4
Template Revision D
Comments
Briefly describe all repairs/adjustments made and list all parts replaced:
___________________________________________________________________________________________________
___________________________________________________________________________________________________
DPMFRM-022
Page 3 of 4
Template Revision D
FRU Checkout Procedure
FRU
Description*
Tools Visual
Inspection
Cleaning Calibration Electrical
Safety Tests
Checkout
Procedure
CASE 8000 Stress Test
Main CPU Mother Pcb
1,3,5 - - 1 3 A thru F
Acquistion I/F Pcb 1,3,5 1,2 - 1 3 A thru F
Network Pcb 1,3,5 - - 1 3 A thru F
Analog I/O Panel 1,3,5 - - 1 3 A thru F
Writer CPU Pcb 1,3,5 - - 1 3 A thru F
Writer Power Supply 1,3,5 - - 1 3 A thru F
Printhead 1,3,5 - - 1 3 A thru F
Hard Drive 1,3,5 - - 1 3 A thru F
Floppy Drive 1,3,5 - - 1 3 A thru F
Video Pcb 1,3,5 - - 1 3 A thru F
Software - - - 1,2 A thru F
Hardware Upgrades
(Including Firmware)
Perform complete PM
Supplies Perform applicable Checkout Procedure(s)
Non-Listed FRUs Perform complete PM
No Parts Replaced Perform applicable Checkout Procedure(s)
* The FRU Checkout procedure for any listed FRU also applies to its internal PCBs and parts.
DPMFRM-022
Page 4 of 4
Template Revision D

You might also like