MSS SP-43-2008

MSS SP- 43 - 2008
Wrought and Fabricated

Butt-Welding Fittings
for Low Pressure,
Corrosion Resistant
Applications
Standard Practice
Developed and Approved by the
Manufacturers Standardization Society of the
Valve and Fittings Industry, Inc.
127 Park Street, NE
Vienna, Virginia 22180
Phone: (703) 281-6613
Fax: (703) 281-6671
Email: [email protected]
www.mss-hq.org
Copyright MSS
Provided by IHS under license with MSS Licensee=Parsons Corp - WAN Charlotte NC /9989682100
Not for Resale, 07/15/2009 15:14:47 MDT No reproduction or networking permitted without license from IHS
--`,`,,`,`,,,`,``,``,,```,,`,`,`-`-`,,`,,`,`,,`---
MSS STANDARD PRACTICE SP-43

i
This MSS Standard Practice was developed under the consensus of the MSS Technical Committee 113 and
the MSS Coordinating Committee. The content of this Standard Practice is the result of the efforts of
competent and concerned volunteers to provide an effective, clear, and non-exclusive specification that will
benefit the industry as a whole. This MSS Standard Practice is intended as a basis for common practice by
the manufacturer, the user, and the general public. The existence of an MSS Standard Practice does not in
itself preclude the manufacture, sale, or use of products not conforming to the Standard Practice. Mandatory
conformance is established only by reference in a code, specification, sales contract, or public law, as
applicable.

Unless otherwise specifically noted in this MSS SP, any standard referred to herein is
identified by the date of issue that was applicable to the referenced standard(s) at the date
of issue of this MSS SP. (See Annex A).

This document has been substantially revised from the previous 1991 (R 2001)
edition. It is suggested that if the user is interested in knowing what changes have
been made, that direct page-by-page comparison should be made of this
document with the previous edition.

Any part of this Standard Practice may be quoted. Credit lines should read 'Extracted from MSS SP-43, 2008,
with permission of the publisher, the Manufacturers Standardization Society.' Reproduction prohibited under
copyright convention unless written permission is granted by the Manufacturers Standardization Society of the

Originally Approved October, 1950

Copyright 1982 by
Manufacturers Standardization Society
of the
Printed in U.S.A.
Copyright MSS
-
-
`
,
`
,
,
`
,
`
,
,
,
`
,
`
`
,
`
`
,
,
`
`
`
,
,
`
,
`
,
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-

ii

FOREWORD

ASME B16.9 is the American Standard for steel butt-welding fittings and although not so
stated, it is implied that its scope deals primarily with the schedules of wall thicknesses which are
common to carbon steel and the grades of alloy steel piping that are selected for pressure and
temperature considerations.

The rapid expansion of the process industries in the field of chemicals, plastics, textiles, etc.,
has created a demand for a class of pipe referred to as stainless piping, using this word in its generic sense.
This field employs the use of the austenitic stainless steels and also nickel and its related alloys. This
stainless piping is used with resistance to corrosion, elimination of product contamination, or
combination of the two as the principle reason for material selection. Pressure is seldom, if ever, a
critical consideration.

When pressure is a consideration reference is made to ASME B16.9.

Mechanical strength, resistance to vacuum, and economy, are the most usual criteria in the
selection of pipe thickness in this field, and for this reason the wall thicknesses employed in the field of
corrosion resistant pipe are lighter than those in common usage with carbon steel piping.

In 1949 ANSI approved standard B36.19 Stainless Steel Pipe in which a schedule of wall
thickness was established and designated as Schedule 10S. Numerous companies were also using a wall
thickness lighter than Schedule 10S for services where contamination rather than corrosion was the
prime consideration. These lighter wall thicknesses were designated Schedule 5S and the original 1950
edition of SP-43 established a series of Schedule 5S fittings. The 5S thicknesses were published in SP-
43 and were developed in cooperation with representatives of the various principal chemical companies
and processing industries. In 1952 the Stainless Steel Pipe Standard B36.19 was revised to recognize the
Schedule 5S wall thickness pipe as American Standard.

The purpose of this Standard Practice is to provide industry with a set of dimensional standards
for butt-welding fittings that can be used with these light wall pipes of corrosion resisting materials. The
center-to-end dimensions of all fittings are identical with those in ASME B16.9 which give to industry
the advantage of uniform design room practice and a maximum utilization of existing die equipment.
The only departure from this is in the lap-joint stub end where for purposes of economy the face-to-end
of the product has been reduced for use with thin wall piping.

The advantage of longer center-to-end dimensions of the size 3/4 elbows resulted in the change
in the tables to permit a gradual changeover, providing the manufacturers ample time to deplete existing
stocks, re-tool and replenish stocks.

The 1991 revision of the SP was required to delete the metric equivalents.

The 2001 Reaffirmation had no technical changes. There were minor editorial changes. The
precedence of the longer dimensions for 3/4 elbows was made in accordance with ASME B16.9.
Referenced standards were brought up to date. The title of 180 degree returns was clarified.

In this 2008 edition, a minimal pressure rating is established to correspond with the ASTM CR
designation.

Copyright MSS
--`,`,,`,`,,,`,``,``,,```,,`,`,`-`-`,,`,,`,`,,`---

iii
TABLE OF CONTENTS

SECTION PAGE

1 SCOPE............................................................................................................................................. 1
2 REFERENCES................................................................................................................................ 1
3 PRESSURE RATINGS................................................................................................................... 1
4 SIZE................................................................................................................................................. 1
5 MARKING ..................................................................................................................................... 1
6 MATERIALS ................................................................................................................................. 2
7 METAL THICKNESS ................................................................................................................... 2
8 FITTINGS DIMENSIONS.............................................................................................................. 2
9 TESTS ............................................................................................................................................. 2
10 TOLERANCES .............................................................................................................................. 2
11 WELDING BEVEL ........................................................................................................................ 2
12 FINISH AND HEAT TREATMENT ............................................................................................. 2

TABLE

1 Tolerances........................................................................................................................................ 3
2 Dimensions of Long Radius Elbows ............................................................................................... 4
3 Dimensions of Straight and Reducing-on-the-Outlet Tees.............................................................. 5
4 Dimensions of Lap-Joint Stub Ends and Caps ................................................................................ 7
5 Dimensions of Long Radius 180 Degree Returns .......................................................................... 8
6 Dimensions of Concentric and Eccentric Reducers ........................................................................ 9

ANNEX

A Referenced Standards and Applicable Dates ................................................................................ 10
Copyright MSS
--`,`,,`,`,,,`,``,``,,```,,`,`,`-`-`,,`,,`,`,,`---

1
1. SCOPE
1.1 This Standard Practice provides dimensions,
tolerances, and markings for butt-welding fittings
for low pressure, corrosion resistant applications.
1.2 This Standard Practice covers only fittings
made for use with Schedule 5S or 10S pipe, for all
NPS sizes listed in ASME B36.19M, except that for
short pattern stub ends suitable for use with
Schedule 40S are also shown.

2. REFERENCES
2.1 Standards and specifications adopted by
reference in this Standard Practice are shown in
Annex A for convenience of identifying edition
number, date, and source of supply.

3. PRESSURE RATINGS
3.1 Fittings covered by this Standard Practice are
not pressure rated; however, they must be capable
of withstanding 30% of the allowable pressure
rating of the pipe with which they are marked.
3.2 For fittings of same pressure rating of
matching pipe, refer to ASME B16.9.

4. SIZE

4.1 The size of the fittings in Tables 1 through 6
are identified by the corresponding nominal pipe
size.

5. MARKING

5.1 Each fitting shall be marked to show the
following:
a) Manufacturers name or trademark
b) CR followed by the material identification
symbol established for the respective grade in
the appropriate ASTM or AISI specifications
c) Manufacturers heat identification number
d) Schedule number or nominal wall thickness
designation
e) Size

5.2 Where the size of the fittings does not permit
complete marking, Sections 5.1 a) and c) are
mandatory. The other marking and identification
marks may be omitted in the sequence specified in
MSS SP-25.
5.3 The required markings shall be made by any
suitable method that is not injurious to the fitting.

WROUGHT AND FABRICATED BUTT-WELDING FITTINGS
FOR LOW PRESSURE, CORROSION RESISTANT APPLICATIONS
Copyright MSS
--`,`,,`,`,,,`,``,``,,```,,`,`,`-`-`,,`,,`,`,,`---

2
6. MATERIALS

6.1 Fittings made from AISI Types 304, 304L,
347, 316, and 316L are considered standard under
this specification. Fittings made from other
corrosion resistant material, including nonferrous,
materials are acceptable by agreement between the
purchaser and the manufacturer provided they meet
the requirements of a recognized AISI or ASTM
specification.

7. METAL THICKNESS

7.1 As these fittings are to match pipe, the
dimensions of the welding ends must conform to
established pipe standards as to outside diameters
and tolerances. The nominal wall thickness of the
fittings shall be the same as the pipe to which it is
welded, except that fittings with heavier walls may
be butt-welded to lighter wall pipe provided the
heavier wall is tapered on the inside or outside to
match the dimensions of the lighter pipe.

8. FITTINGS DIMENSIONS

8.1 Inch dimensions for the fittings covered by this
Standard Practice are given in Tables 1 through 6.

8.2 One of the principals of this Standard Practice
is the maintenance of a fixed position for welding
ends with reference to center line of the fittings or
the overall dimensions as the case may be.

9. TESTS

9.1 Hydrostatic testing of fittings is not required in
this Standard Practice; however, fittings shall be
capable of withstanding a hydrostatic test pressure
that is 1.5 times the pressure rating required in
Section 3.1.

10. TOLERANCES

10.1 Table 1 lists the tolerances for the fittings
covered by this Standard Practice.

11. WELDING BEVEL

11.1 Fittings furnished to this Standard Practice
may be finished with ends cut square for wall
thickness 0.12 in. or less. For wall thicknesses in
excess of 0.12 in., they shall be beveled at 37 l/2
plus or minus 2 l/2 with root face (land) 0.06 in.
plus or minus 0.03 in.

12. FINISH AND HEAT TREATMENT

12.1 The fittings shall be satisfactorily heat treated
by an accepted practice, and adequately cleaned to
insure maximum corrosion resistance.

Copyright MSS
-
-
`
,
`
,
,
`
,
`
,
,
,
`
,
`
`
,
`
`
,
,
`
`
`
,
,
`
,
`
,
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-

3

O
u
t
s
i
d
e

D
i
a
m
e
t
e
r

o
f

L
a
p

G

+

0

-

0
.
0
3

+

0

-

0
.
0
3

+

0

-

0
.
0
3

+

0

-

0
.
0
3

+

0

-

0
.
0
6

+

0

-

0
.
0
6

L
a
p
-
J
o
i
n
t

S
t
u
b

E
n
d
s

F
i
l
l
e
t

(
b
)

R
a
d
i
u
s

o
f

L
a
p

A

+

0

-

0
.
0
3

+

0

-

0
.
0
3

+

0

-

0
.
0
3

+

0

-

0
.
0
6

+

0

-

0
.
0
6

+

0

-

0
.
0
6

C
a
p
s

O
v
e
r
a
l
l

L
e
n
g
t
h

E

0
.
1
2

0
.
1
2

0
.
1
2

0
.
2
5

0
.
2
5

0
.
2
5

A
l
i
g
n
-

m
e
n
t

o
f

E
n
d
s

U

0
.
0
3

0
.
0
3

0
.
0
3

0
.
0
3

0
.
0
6

0
.
0
6

B
a
c
k
-
t
o
-

F
a
c
e

D
i
m
e
n
s
i
o
n

K

0
.
2
5

0
.
2
5

0
.
2
5

0
.
2
5

0
.
2
5

0
.
2
5

1
8
0

R
e
t
u
r
n
s

C
e
n
t
e
r
-
t
o
-

C
e
n
t
e
r

D
i
m
e
n
s
i
o
n

O

0
.
2
5

0
.
2
5

0
.
2
5

0
.
2
5

0
.
3
8

0
.
3
8

R
e
d
u
c
e
r
s

L
a
p
-
J
o
i
n
t

S
t
u
b

E
n
d
s

O
v
e
r
a
l
l

L
e
n
g
t
h

F
-
H

0
.
0
6

0
.
0
6

0
.
0
6

0
.
0
6

0
.
0
9

0
.
0
9

9
0

E
l
b
o
w
s

4
5

E
l
b
o
w
s

T
e
e
s

C
e
n
t
e
r
-
t
o

E
n
d

D
i
m
e
n
s
i
o
n

A
-
B
-
C
-
M

0
.
0
6

0
.
0
6

0
.
0
6

0
.
0
6

0
.
0
9

0
.
0
9

W
a
l
l

T
h
i
c
k
-

n
e
s
s

N
o
t

l
e
s
s

t
h
a
n

8
7

%

o
f

n
o
m
i
n
a
l

t
h
i
c
k
-

n
e
s
s

A
l
l

F
i
t
t
i
n
g
s

O
u
t
s
i
d
e

(
a
)

D
i
a
m
e
t
e
r

a
t

W
e
l
d
i
n
g

E
n
d

0
.
0
3

0
.
0
3

0
.
0
3

+

0
.
0
6

-

0
.
0
3

+

0
.
0
9

-

0
.
0
3

+

0
.
1
2

-

0
.
0
3

N
o
m
i
n
a
l

P
i
p
e

S
i
z
e

1
/
2

-

1
-
1
/
2

2

-

3
-
1
/
2

4

5

-

8

1
0

-

1
8

2
0

-

2
4

N
O
T
E
S
:

D
i
a
m
e
t
e
r

a
n
d

w
a
l
l

t
h
i
c
k
n
e
s
s
e
s

a
s

s
p
e
c
i
f
i
e
d

i
n

e
i
t
h
e
r

A
S
M
E

B

3
6
.
1
0
M

o
r

A
S
M
E

B

3
6
.
1
9
M

(
a
)

O
u
t

o
f

r
o
u
n
d
n
e
s
s

i
s

t
h
e

v
e
c
t
o
r

s
u
m

o
f

p
l
u
s

a
n
d

m
i
n
u
s

t
o
l
e
r
a
n
c
e
.

(
b
)

F
i
l
l
e
t

B

r
a
d
i
u
s

i
s

m
a
x
i
m
u
m
.

(
S
e
e

T
a
b
l
e

4
)
.

T
a
b
l
e

1

T
o
l
e
r
a
n
c
e
s

D
i
m
e
n
s
i
o
n
s

i
n

i
n
c
h
e
s

Copyright MSS
-
-
`
,
`
,
,
`
,
`
,
,
,
`
,
`
`
,
`
`
,
,
`
`
`
,
,
`
,
`
,
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-

4

TABLE 2
Dimensions of Long Radius Elbows

Dimensions in inches
Center-to-End
Nominal
Pi pe
Si z e
Outside
Diameter
At Bevel
90-Deg
Elbows
A
45-Deg
Elbows
B
1/2 0.84 1.50 0.62
3/4 1.05 1.50 0.75
1 1.32 1.50 0.88
1-1/4 1.66 1.88 1.00
1-1/2 1.90 2.25 1.12

2 2.38 3.00 1.38
2-1/2 2.88 3.75 1.75
3 3.50 4.50 2.00
3-1/2 4.00 5.25 2.25
4 4.50 6.00 2.50

5 5.56 7.50 3.12
6 6.62 9.00 3.75
8 8.62 12.00 5.00
10 10.75 15.00 6.25
12 12.75 18.00 7.50

14 14.00 21.00 8.75
16 16.00 24.00 10.00
18 18.00 27.00 11.25
20 20.00 30.00 12.50
22 22.00 33.00 13.50
24 24.00 36.00 15.00

Copyright MSS
-
-
`
,
`
,
,
`
,
`
,
,
,
`
,
`
`
,
`
`
,
,
`
`
`
,
,
`
,
`
,
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-

5

TABLE 3
Dimensions of Straight and Reducing-on-the-Outlet Tees
Nominal Outside
Diameter at Bevel
Center-to-End
Nominal
Pipe
Size

Run

Outlet
Run
C
Outlet
M

1/2 Straight 0.84 0.84 1.00 1.00
3/4 Straight 1.05 1.05 1.12 1.12
3/4 x 3/4 x 1/2 1.05 0.84 1.12 1.12

1 Straight 1.32 1.32 1.50 1.50
1 x 1 x 3/4 1.32 1.05 1.50 1.50
1 x 1 x 1/2 1.32 0.84 1.50 1.50

1-1/4 Straight 1.66 1.66 1.88 1.88
1-1/4 x 1-1/4 x 1 1.66 1.32 1.88 1.88
1-1/4 x 1-1/4 x 3/4 1.66 1.05 1.88 1.88
1-1/4 x 1-1/4 x 1/2 1.66 0.84 1.88 1.88

1-1/2 Straight 1.90 1.90 2.25 2.25
1-1/2 x 1-1/2 x 1-1/4 1.90 1.66 2.25 2.25
1-1/2 x 1-1/2 x 1 1.90 1.32 2.25 2.25
1-1/2 x 1-1/2 x 3/4 1.90 1.05 2.25 2.25

2 Straight 2.38 2.38 2.50 2.50
2 x 2 x 1-1/2 2.38 1.90 2.50 2.38
2 x 2 x 1-1/4 2.38 1.66 2.50 2.25
2 x 2 x 1 2.38 1.32 2.50 2.00
2 x 2 x 3/4 2.38 1.05 2.50 1.75

2-1/2 Straight 2.88 2.88 3.00 3.00
2-1/2 x 2-1/2 x 2 2.88 2.38 3.00 2.75
2-1/2 x 2-1/2 x 1-1/2 2.88 1.90 3.00 2.62
2-1/2 x 2-1/2 x 1-1/4 2.88 1.66 3.00 2.50
2-1/2 x 2-1/2 x 1 2.88 1.32 3.00 2.25

3 Straight 3.50 3.50 3.38 3.38
3 x 3 x 2-1/2 3.50 2.88 3.38 3.25
3 x 3 x 2 3.50 2.38 3.38 3.00
3 x 3 x 1-1/2 3.50 1.90 3.38 2.88

3-1/2 Straight 4.00 4.00 3.75 3.75
3-1/2 x 3-1/2 x 3 4.00 3.50 3.75 3.62
3-1/2 x 3-1/2 x 2-1/2 4.00 2.88 3.75 3.50
3-1/2 x 3-1/2 x 2 4.00 2.38 3.75 3.25
3-1/2 x 3-1/2 x 1-1/2 4.00 1.90 3.75 3.12

4 Straight 4.50 4.50 4.12 4.12
4 x 4 x 3-1/2 4.50 4.00 4.12 4.00
4 x 4 x 3 4.50 3.50 4.12 3.88
4 x 4 x 2-1/2 4.50 2.88 4.12 3.75
4 x 4 x 2 4.50 2.38 4.12 3.50
4 x 4 x 1-1/2 4.50 1.90 4.12 3.38

5 Straight 5.56 5.56 4.88 4.88
5 x 5 x 4 5.56 4.50 4.88 4.62
5 x 5 x 3-1/2 5.56 4.00 4.88 4.50
5 x 5 x 3 5.56 3.50 4.88 4.38
5 x 5 x 2-1/2 5.56 2.88 4.88 4.25
5 x 5 x 2 5.56 2.38 4.88 4.12

Copyright MSS
-
-
`
,
`
,
,
`
,
`
,
,
,
`
,
`
`
,
`
`
,
,
`
`
`
,
,
`
,
`
,
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-

6
TABLE 3
Dimensions of Straight and Reducing-on-the-Outlet Tees
(Continued)

Nominal Outside
Diameter at Bevel
Center-to-End
Run Outlet

Nominal
Pipe
Size
Run Outlet C M
6 Straight 6.62 6.62 5.62 5.62
6 x 6 x 5 6.62 5.56 5.62 5.38
6 x 6 x 4 6.62 4.50 5.62 5.12
6 x 6 x 3-1/2 6.62 4.00 5.62 5.00
6 x 6 x 3 6.62 3.50 5.62 4.88
6 x 6 x 2-1/2 6.62 2.88 5.62 4.75

8 Straight 8.62 8.62 7.00 7.00
8 x 8 x 6 8.62 6.62 7.00 6.62
8 x 8 x 5 8.62 5.56 7.00 6.38
8 x 8 x 4 8.62 4.50 7.00 6.12
8 x 8 x 3-1/2 8.62 4.00 7.00 6.00

10 Straight 10.75 10.75 8.50 8.50
10 x 10 x 8 10.75 8.62 8.50 8.00
10 x 10 x 6 10.75 6.62 8.50 7.62
10 x 10 x 5 10.75 5.56 8.50 7.50
10 x 10 x 4 10.75 4.50 8.50 7.25

12 Straight 12.75 12.75 10.00 10.00
12 x 12 x 10 12.75 10.75 10.00 9.50
12 x 12 x 8 12.75 8.62 10.00 9.00
12 x 12 x 6 12.75 6.62 10.00 8.62
12 x 12 x 5 12.75 5.56 10.00 8.50

14 Straight 14.00 14.00 11.00 11.00
14 x 14 x 12 14.00 12.75 11.00 10.62
14 x 14 x 10 14.00 10.75 11.00 10.12
14 x 14 x 8 14.00 8.62 11.00 9.75
14 x 14 x 6 14.00 6.62 11.00 9.38

16 Straight 16.00 16.00 12.00 12.00
16 x 16 x 14 16.00 14.00 12.00 12.00
16 x 16 x 12 16.00 12.75 12.00 11.62
16 x 16 x 10 16.00 10.75 12.00 11.12
16 x 16 x 8 16.00 8.62 12.00 10.75
16 x 16 x 6 16.00 6.62 12.00 10.38

18 Straight 18.00 18.00 13.50 13.50
18 x 18 x 16 18.00 16.00 13.50 13.00
18 x 18 x 14 18.00 14.00 13.50 13.00
18 x 18 x 12 18.00 12.75 13.50 12.62
18 x 18 x 10 18.00 10.75 13.50 12.12
18 x 18 x 8 18.00 8.62 13.50 11.75

20 Straight 20.00 20.00 15.00 15.00
20 x 20 x 18 20.00 18.00 15.00 14.50
20 x 20 x 16 20.00 16.00 15.00 14.00
20 x 20 x 14 20.00 14.00 15.00 14.00
20 x 20 x 12 20.00 12.75 15.00 13.62
20 x 20 x 10 20.00 10.75 15.00 13.12
20 x 20 x 8 20.00 8.62 15.00 12.75

24 Straight 24.00 24.00 17.00 17.00
24 x 24 x 20 24.00 20.00 17.00 17.00
24 x 24 x 18 24.00 18.00 17.00 16.50
24 x 24 x 16 24.00 16.00 17.00 16.00
24 x 24 x 14 24.00 14.00 17.00 16.00
24 x 24 x 12 24.00 12.75 17.00 15.62
24 x 24 x 10 24.00 10.75 17.00 15.12

Copyright MSS
--`,`,,`,`,,,`,``,``,,```,,`,`,`-`-`,,`,,`,`,,`---

7

TABLE 4
Dimensions of Lap-Joint Stub Ends and Caps

Lap-Joint Stub Ends
(c)

Radius of Fillet
Nominal
Pipe
Size
Nominal
O. D. at
Bevel
Caps
Length E
Length F
Dia. of Lap-G
Nominal &
Maximum
A Nominal
& Max
B
Max
1/2 0.84 1.00 2.00 1.38 0.12 0.03
3/4 1.05 1.00 2.00 1.69 0.12 0.03
1 1.32 1.50 2.00 2.00 0.12 0.03
1-1/4 1.66 1.50 2.00 2.50 0.19 0.03
1-1/2 1.90 1.50 2.00 2.88 0.25 0.03
2 2.38 1.50 2.50 3.62 0.31 0.03
2-1/2 2.88 1.50 2.50 4.12 0.31 0.03
3 3.50 2.00 2.50 5.00 0.38 0.03
3-1/2 4.00 2.50 3.00 5.50 0.38 0.03
4 4.50 2.50 3.00 5.50 0.38 0.03
5 5.56 3.00 3.00 7.31 0.44 0.06
6 6.62 3.50 3.50 8.50 0.50 0.06
8 8.62 4.00 4.00 10.62 0.50 0.06
10 10.75 5.00 5.00 12.75 0.50 0.06
12 12.75 6.00 6.00 15.00 0.50 0.06
14 14.00 6.50 6.00 16.25 0.50 0.06
16 16.00 7.00 6.00 18.50 0.50 0.06
18 18.00 8.00 6.00 21.00 0.50 0.06
20 20.00 9.00 6.00 23.00 0.50 0.06
24 24.00 10.50 6.00 27.25 0.50 0.06

NOTES:

(a)
Minimum lap thickness shall not be less than nominal wall thickness.
(b)
Connect faces of stub ends shall have a modified spiral or concentric serration.
(c)
These lengths and radii for use with Schedule 40S or thinner pipe.

Copyright MSS
-
-
`
,
`
,
,
`
,
`
,
,
,
`
,
`
`
,
`
`
,
,
`
`
`
,
,
`
,
`
,
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-

8

TABLE 5
Dimensions of Long Radius 180 Degree Returns

Nominal
Pipe
Size
Outside
Diameter
At Bevel
Center-
to-Center
O
Back-to-
Face
K
1/2 0.84 3.00 1.88
3/4 1.05 2.25 1.69
1 1.32 3.00 2.19
1-1/4 1.66 3.75 2.75
1-1/2 1.90 4.50 3.25
2 2.38 6.00 4.19
2-1/2 2.88 7.50 5.19
3 3.50 9.00 6.25
3-1/2 4.00 10.50 7.25
4 4.50 12.00 8.25
5 5.56 15.00 10.31
6 6.62 18.00 12.31
8 8.62 24.00 16.31
10 10.75 30.00 20.38
12 12.75 36.00 24.38
14 14.00 42.00 28.00
16 16.00 48.00 32.00
18 18.00 54.00 36.00
20 20.00 60.00 40.00
24 24.00 72.00 48.00

NOTES:

(a)
Alignment of ends -U - for nom pipe size 8 and smaller
0.03 in. and for size 10 and larger 0.06 in.

(b)
A dimension is equal to 1/2 O dimension.

Copyright MSS
--`,`,,`,`,,,`,``,``,,```,,`,`,`-`-`,,`,,`,`,,`---

9

TABLE 6
Dimensions of Concentric and Eccentric Reducers

Dimensions in inches Dimensions in inches
Outside Diameter
at Bevel

Nominal
Pipe
Size
Large
End
Small
End
Length
H
6 x 5 6.62 5.56 5.50

6 x 4 6.62 4.50 5.50

6 x 3-1/2 6.62 4.00 5.50

6 x 3 6.62 3.50 5.50

6 x 2-1/2 6.62 2.88 5.50

8 x 6 8.62 6.62 6.00

8 x 5 8.62 5.56 6.00

8 x 4 8.62 4.50 6.00

8 x 3-1/2 8.62 4.00 6.00

10 x 8 10.75 8.62 7.00

10 x 6 10.75 6.62 7.00

10 x 5 10.75 5.56 7.00

10 x 4 10.75 4.50 7.00

12 x 10 12.75 10.75 8.00

12 x 8 12.75 8.62 8.00

12 x 6 12.75 6.62 8.00

12 x 5 12.75 5.56 8.00
14 x 12 14.00 12.75 13.00

14 x 10 14.00 10.75 13.00

14 x 8 14.00 8.62 13.00

14 x 6 14.00 6.62 13.00

16 x 14 16.00 14.00 14.00

16 x 12 16.00 12.75 14.00

16 x 10 16.00 10.75 14.00

16 x 8 16.00 8.62 14.00

18 x 16 18.00 16.00 15.00

18 x 14 18.00 14.00 15.00

18 x 12 18.00 12.75 15.00

18 x 10 18.00 10.75 15.00

20 x 18 20.00 18.00 20.00

20 x 16 20.00 16.00 20.00

20 x 14 20.00 14.00 20.00

20 x 12 20.00 12.75 20.00

24 x 20 24.00 20.00 20.00

24 x 18 24.00 18.00 20.00

24 x 16 24.00 16.00 20.00

Outside Diameter
at Bevel

Nominal
Pipe
Size
Large
End
Small
End
Length
H

3/4 x 1/2 1.05 0.84 1.50

1 x 3/4 1.32 1.05 2.00
1 x 1/2 1.32 0.84 2.00
1 x 3/8 1.32 0.68 2.00
1-1/4 x 1 1.66 1.32 2.00

1-1/4 x 3/4 1.66 1.05 2.00
1-1/4 x 1/2 1.66 0.84 2.00
1-1/2 x 1-1/4 1.90 1.66 2.50

1-1/2 x 1 1.90 1.32 2.50
1-1/2 x 3/4 1.90 1.05 2.50
1-1/2 x 1/2 1.90 0.84 2.50
2 x 1-1/2 2.38 1.90 3.00

2 x 1-1/4 2.38 1.66 3.00
2 x 1 2.38 1.32 3.00
2 x 3/4 2.38 1.05 3.00
2-1/2 x 2 2.88 2.38 3.50

2-1/2 x 1-1/2 2.88 1.90 3.50
2-1/2 x 1-1/4 2.88 1.66 3.50
2-1/2 x 1 2.88 1.32 3.50
3 x 2-1/2 3.50 2.88 3.50

3 x 2 3.50 2.88 3.50
3 x 1-1/2 3.50 1.90 3.50
3 x 1-1/4 3.50 1.66 3.50
3 x 1/2 x 3 4.00 3.50 4.00

3 x 1/2 x 2-1/2 4.00 2.88 4.00
3-1/2 x 2 4.00 2.38 4.00
3-1/2 x 1-1/2 4.00 1.90 4.00
3-1/2 x 1-1/4 4.00 1.66 4.00
4 x 3-1/2 4.50 4.00 4.00

4 x 3 4.50 3.50 4.00
4 x 2-1/2 4.50 2.88 4.00
4 x 2 4.50 2.38 4.00
4 x 1-1/2 4.50 1.90 4.00
5 x 4 5.56 4.50 5.00

5 x 3-1/2 5.56 4.00 5.00
5 x 3 5.56 3.50 5.00
5 x 2-1/2 5.56 2.88 5.00
5 x 2 5.56 2.38 5.00

Copyright MSS
-
-
`
,
`
,
,
`
,
`
,
,
,
`
,
`
`
,
`
`
,
,
`
`
`
,
,
`
,
`
,
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-

10
ANNEX A

Referenced Standards and Applicable Dates

This Annex is an integral part of this Standard Practice and is placed after the main text for convenience.

Standard Name or Description

ASME, ANSI/ASME, ANSI, ASME/ANSI

ASME B16.9 2003 Factory-Made Wrought Steel Buttwelding Fittings
ASME B36.10M 2004 Welded and Seamless Wrought Steel Pipe
ASME B36.19M 2004 Stainless Steel Pipe

MSS

SP-25-1998 Standard Marking System for Valves, Fittings, Flanges and Unions

Publications of the following organizations appear in the above list:

AISI American Iron and Steel Institute
1101 17th Street, N.W.
Washington, D.C. 20036-4700

ANSI American National Standards Institute
25 West 43rd Street
New York, NY 10036

ASME ASME International
Three Park Avenue
New York, NY 10016-5990

ASTM ASTM International
100 Barr Harbor Drive
West Conshohocken, PA 19428-2959

MSS Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.
127 Park Street, N.E.
Vienna, VA 22180-4602

Copyright MSS
-
-
`
,
`
,
,
`
,
`
,
,
,
`
,
`
`
,
`
`
,
,
`
`
`
,
,
`
,
`
,
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-

List of MSS Standard Practices
(Price List Available Upon Request)
Number
SP-6-2007 Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings
SP-9-2008 Spot Facing for Bronze, Iron and Steel Flanges
SP-25-2008 Standard Marking System for Valves, Fittings, Flanges and Unions
SP-42-2004 Class 150 Corrosion Resistant Gate, Glove, Angle and Check Valves with Flanged and Butt Weld Ends
SP-43-2008 Wrought and Fabricated Butt-Welding Fittings for Low Pressure, Corrosion Resistant Applications
SP-44-2006 Steel Pipeline Flanges
SP-45-2003 (R 08) Bypass and Drain Connections
SP-51-2007 Class 150LW Corrosion Resistant Flanges and Cast Flanged Fittings
SP-53-1999 (R 07) Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fittings and Other Piping Components - Magnetic Particle
Examination Method
SP-54-1999 (R 07) Quality Standard for Steel Castings for Valves, Flanges, and Fittings and Other Piping Components - Radiographic Examination Method
SP-55-2006 Quality Standard for Steel Castings for Valves, Flanges and Fittings and Other Piping Components - Visual Method for Evaluation of
Surface Irregularities
SP-58-2002 Pipe Hangers and Supports - Materials, Design and Manufacture
SP-60-2004 Connecting Flange Joint Between Tapping Sleeves and Tapping Valves
SP-61-2003 Pressure Testing of Steel Valves
SP-65-2008 High Pressure Chemical Industry Flanges and Threaded Stubs for Use with Lens Gaskets
SP-67-2002a Butterfly Valves
SP-68-1997 (R 04) High Pressure Butterfly Valves with Offset Design
SP-69-2003 Pipe Hangers and Supports - Selection and Application (ANSI/MSS Edition)
SP-70-2006 Gray Iron Gate Valves, Flanged and Threaded Ends
SP-71-2005 Gray Iron Swing Check Valves, Flanged and Threaded Ends
SP-72-1999 Ball Valves with Flanged or Butt-welding Ends for General Service
SP-75-2004 Specification for High Test Wrought Butt Welding Fittings
SP-77-1995 (R 00) Guidelines for Pipe Support Contractual Relationships
SP-78-2005a Gray Iron Plug Valves, Flanged and Threaded Ends
SP-79-2004 Socket-Welding Reducer Inserts
SP-80-2008 Bronze Gate, Globe, Angle and Check Valves
SP-81-2006a Stainless Steel, Bonnetless, Flanged, Knife Gate Valves
SP-83-2006 Class 3000 Steel Pipe Unions, Socket-Welding and Threaded
SP-85-2002 Gray Iron Globe & Angle Valves, Flanged and Threaded Ends
SP-86-2002 Guidelines for Metric Data in Standards for Valves, Flanges, Fittings and Actuators
SP-88-1993 (R 01) Diaphragm Valves
SP-89-2003 Pipe Hangers and Supports - Fabrication and Installation Practices
SP-90-2000 Guidelines on Terminology for Pipe Hangers and Supports
SP-91-1992 (R 96) Guidelines for Manual Operation of Valves
SP-92-1999 MSS Valve User Guide
SP-93-1999 (R 04) Quality Standard for Steel Castings and Forgings for Valves, Flanges, and Fittings and Other Piping Components - Liquid Penetrant
Examination Method
SP-94-1999 (R 04) Quality Std for Ferritic and Martensitic Steel Castings for Valves, Flanges, and Fittings and Other Piping Components - Ultrasonic
Examination Method
SP-95-2006 Swage(d) Nipples and Bull Plugs
SP-96-2001 (R 05) Guidelines on Terminology for Valves and Fittings
SP-97-2006 Integrally Reinforced Forged Branch Outlet Fittings - Socket Welding, Threaded and Buttwelding Ends
SP-98-2001 (R 05) Protective Coatings for the Interior of Valves, Hydrants, and Fittings
SP-99-1994 (R 05) Instrument Valves
SP-100-2002 Qualification Requirements for Elastomer Diaphragms for Nuclear Service Diaphragm Valves
SP-101-1989 (R 01) Part-Turn Valve Actuator Attachment - Flange and Driving Component Dimensions and Performance Characteristics
SP-102-1989 (R 01) Multi-Turn Valve Actuator Attachment - Flange and Driving Component Dimensions and Performance Characteristics
SP-104-2003 Wrought Copper Solder Joint Pressure Fittings
SP-105-1996 (R 05) Instrument Valves for Code Applications
SP-106-2003 Cast Copper Alloy Flanges and Flanged Fittings, Class 125, 150 and 300
SP-108-2002 Resilient-Seated Cast-Iron Eccentric Plug Valves
SP-109-1997 (R 06) Welded Fabricated Copper Solder Joint Pressure Fittings
SP-110-1996 Ball Valves Threaded, Socket-Welding, Solder Joint, Grooved and Flared Ends
SP-111-2001 (R 05) Gray-Iron and Ductile-Iron Tapping Sleeves
SP-112-1999 (R 04) Quality Standard for Evaluation of Cast Surface Finishes -Visual and Tactile Method. This SP must be sold with a 10-surface, three
Dimensional Cast Surface Comparator, which is a necessary part of the Standard. Additional Comparators may be sold separately.
SP-113-2001 (R 07) Connecting Joint between Tapping Machines and Tapping Valves
SP-114-2007 Corrosion Resistant Pipe Fittings Threaded and Socket Welding, Class 150 and 1000
SP-115-2006 Excess Flow Valves, 1 1/4 NPS and Smaller, for Fuel Gas Service
SP-116-2003 Service Line Valves and Fittings for Drinking Water Systems
SP-117-2006 Bellows Seals for Globe and Gate Valves
SP-118-2007 Compact Steel Globe & Check Valves - Flanged, Flangeless, Threaded & Welding Ends (Chemical & Petroleum Refinery Service)
SP-119-2003 Factory-Made Belled End Socket Welding Fittings
SP-120-2006 Flexible Graphite Packing System for Rising Stem Steel Valves (Design Requirements)
SP-121-2006 Qualification Testing Methods for Stem Packing for Rising Stem Steel Valves
SP-122-2005 Plastic Industrial Ball Valves
SP-123-1998 (R 06) Non-Ferrous Threaded and Solder-Joint Unions for Use with Copper Water Tube
SP-124-2001 Fabricated Tapping Sleeves
SP-125-2000 Gray Iron and Ductile Iron In-Line, Spring-Loaded, Center-Guided Check Valves
SP-126-2007 Steel In-Line Spring-Assisted Center Guided Check Valves
SP-127-2001 Bracing for Piping Systems Seismic-Wind-Dynamic Design, Selection, Application
SP-128-2006 Ductile Iron Gate Valves
SP-129-2003 (R 07) Copper-Nickel Socket-Welding Fittings and Unions
SP-130-2003 Bellows Seals for Instrument Valves
SP-131-2004 Metallic Manually Operated Gas Distribution Valves
SP-132-2004 Compression Packing Systems for Instrument Valves
SP-133-2005 Excess Flow Valves for Low Pressure Fuel Gas Appliances
SP-134-2006a Valves for Cryogenic Service Including Requirements for Body/Bonnet Extensions
SP-135-2006 High Pressure Steel Knife Gate Valves
SP-136-2007 Ductile Iron Swing Check Valves
SP-137-2007 Quality Standard for Positive Material Identification of Metal Valves, Flanges, Fittings, and Other Piping Components
(R-YEAR) Indicates year standard reaffirmed without substantive changes

A large number of former MSS Practices have been approved by the ANSI or ANSI Standards, published by others. In order to maintain a single source
of authoritative information, the MSS withdraws its Standard Practices in such cases.
Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.
127 Park Street, N.E., Vienna, VA 22180-4620 (703) 281-6613 Fax # (703) 281-6671
MSS-IHS SP

Copyright MSS
-
-
`
,
`
,
,
`
,
`
,
,
,
`
,
`
`
,
`
`
,
,
`
`
`
,
,
`
,
`
,
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-

MSS SP-43-2008

Uploaded by

Copyright:

Available Formats

MSS SP-43-2008

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MSS SP-43-2008

Uploaded by

Copyright:

Available Formats

MSS SP- 43 - 2008

Wrought and Fabricated

You might also like