Hardware Requirements and Installation of Server 2008
Hardware Requirements and Installation of Server 2008
Requirements
and Installation
of Server 2008
By
Abhishek Dogra
{B.Sc.IT, JCHNP, MCP, MCSA,
MCSE}
To use Windows Server 2008 you need to meet the following hardware requirements:
Component Requirement
Processor • Minimum: 1GHz (x86 processor) or 1.4GHz (x64 processor) • Recommended:
2GHz or faster Note: An Intel Itanium 2 processor is required for Windows
Server 2008 for Itanium-based Systems
Memory • Minimum: 512MB RAM • Recommended: 2GB RAM or greater • Maximum
(32-bit systems): 4GB (Standard) or 64GB (Enterprise and Datacenter) •
Maximum (64-bit systems): 32GB (Standard) or 2TB (Enterprise, Datacenter and
Itanium-based Systems)
Available Disk • Minimum: 10GB • Recommended: 40GB or greater Note: Computers with
Space more than 16GB of RAM will require more disk space for paging, hibernation,
and dump files
Drive DVD-ROM drive
Display and • Super VGA (800 x 600) or higher-resolution monitor • Keyboard • Microsoft
Peripherals Mouse or compatible pointing device
Upgrade notes:
I will not discuss the upgrade process in this article, but for your general knowledge, the upgrade
paths available for Windows Server 2008 shown in the table below:
If you are currently running: You can upgrade to:
Windows Server 2003 Standard Edition (R2, Full Installation of Windows Server 2008
Service Pack 1 or Service Pack 2) Standard Edition
Full Installation of Windows Server 2008
Enterprise Edition
Windows Server 2003 Enterprise Edition Full Installation of Windows Server 2008
(R2, Service Pack 1 or Service Pack 2) Enterprise Edition
Windows Server 2003 Datacenter Edition Full Installation of Windows Server 2008
(R2, Service Pack 1 or Service Pack 2) Datacenter Edition
<a href="http://ad.doubleclick.net/click%3Bh=v8/384a/3/0/%2a/d%3B215430611%3B0-
0%3B0%3B37193546%3B4307-300/250%3B31701324/31719200/1%3B%3B%7Esscs%3D
%3fhttp://clk.atdmt.com/ZH1/go/153834383/direct;wi.300;hi.250/01/" target="_blank"><img
src="http://view.atdmt.com/ZH1/view/153834383/direct;wi.300;hi.250/01/7078812"/></a><nos
cript><a href="http://ad.doubleclick.net/click%3Bh=v8/384a/3/0/%2a/d%3B215430611%3B0-
0%3B0%3B37193546%3B4307-300/250%3B31701324/31719200/1%3B%3B%7Esscs%3D
%3fhttp://clk.atdmt.com/ZH1/go/153834383/direct;wi.300;hi.250/01/" target="_blank"><img
border="0"
src="http://view.atdmt.com/ZH1/view/153834383/direct;wi.300;hi.250/01/7078812"
/></a></noscript>
6. Because you did not provide the correct ID, the installation process cannot determine what
kind of Windows Server 2008 license you own, and therefore you will be prompted to select
your correct version in the next screen, assuming you are telling the truth and will provide the
correct ID to prove your selection later on.
7. If you did provide the right Product ID, select the Full version of the right Windows version
you're prompted, and click Next.
8. Read and accept the license terms by clicking to select the checkbox and pressing Next.
9. In the "Which type of installation do you want?" window, click the only available option –
Custom (Advanced).
10. In the "Where do you want to install Windows?", if you're installing the server on a
regular IDE hard disk, click to select the first disk, usually Disk 0, and click Next.
If you're installing on a hard disk that's connected to a SCSI controller, click Load Driver and
insert the media provided by the controller's manufacturer.
If you're installing in a Virtual Machine environment, make sure you read the "Installing the
Virtual SCSI Controller Driver for Virtual Server 2005 on Windows Server 2008"
If you must, you can also click Drive Options and manually create a partition on the destination
hard disk.
11. The installation now begins, and you can go and have lunch. Copying the setup files from the
DVD to the hard drive only takes about one minute. However, extracting and uncompressing the
files takes a good deal longer. After 20 minutes, the operating system is installed. The exact time
it takes to install server core depends upon your hardware specifications. Faster disks will
perform much faster installs… Windows Server 2008 takes up approximately 10 GB of hard
drive space.
The installation process will reboot your computer, so, if in step #10 you inserted a floppy disk
(either real or virtual), make sure you remove it before going to lunch, as you'll find the server
hanged without the ability to boot (you can bypass this by configuring the server to boot from a
CD/DVD and then from the hard disk in the booting order on the server's BIOS)
12. Then the server reboots you'll be prompted with the new Windows Server 2008 type of login
screen. Press CTRL+ALT+DEL to log in.
13. Click on Other User.
14. The default Administrator is blank, so just type Administrator and press Enter.
15. You will be prompted to change the user's password. You have no choice but to press Ok.
16. In the password changing dialog box, leave the default password blank (duh, read step
#15…), and enter a new, complex, at-least-7-characters-long new password twice. A password
like "topsecret" is not valid (it's not complex), but one like "T0pSecreT!" sure is. Make sure you
remember it.
17. Someone thought it would be cool to nag you once more, so now you'll be prompted to
accept the fact that the password had been changed. Press Ok.
18. Finally, the desktop appears and that's it, you're logged on and can begin working. You will
be greeted by an assistant for the initial server configuration, and after performing some initial
configuration tasks, you will be able to start working.
Next, for the initial configuration tasks please follow my other Windows Server 2008 articles
found on the Related Windows Server 2008 Articles section below.