400e PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

The Model 400E UV Absorption Ozone Analyzer is a

microprocessor-controlled analyzer that uses a system


based on the Beer-Lambert law for measuring low
ranges of ozone in ambient air.
A 254 nm UV light signal is passed through the sample
cell where it is absorbed in proportion to the amount of
ozone present. Every three seconds, a switching valve
alternates measurement between the sample stream
and a sample that has been scrubbed of ozone. The
result is a true, stable ozone measurement.
Multi-tasking software gives real time indication of a
large number of operational parameters, and provides
automatic warnings if diagnostic limits are exceeded.
Built-in data acquisition capability, using the analyzer's
internal memory, allows the logging of multiple
parameters including averaged or instantaneous
concentration values, calibration data, and operating
parameters such as pressure and flow rate.
Stored data are easily retrieved through the serial port
or optional Ethernet port via our APIcom software or from
the front panel, allowing operators to perform predictive
diagnostics and enhanced data analysis by tracking
parameter trends. Multiple averaging periods of one
minute to 365 days are available for over a period of
one year.
Standard two year warranty
Ranges, 0-100 ppb to 0-10 ppm, user
selectable
Single pass ultraviolet absorption
Microprocessor controlled for versatility
Multi-tasking software allows viewing of test
variables during operation
Continuous self checking with alarms
Dual bi-directional RS-232 ports for remote
operation (optional RS-485 or Ethernet)
Digital status outputs provide instrument
operating condition
Adaptive signal filtering optimizes response
time
Optional Internal Zero/Span check and dual
span points
Temperature & Pressure compensation
Internal data logging with 1 min to 365 day
multiple averages
APIcom remote operation software
UV Absorption O
3
Analyzer
MODEL 400E
E P A A P P R O V A L E Q O A - 0 9 9 2 - 0 8 7
M C E R T S c e r t i f i e d S i r a M C 0 5 0 0 7 0 / 0 0
E N A p p r o v a l E N 1 4 6 2 5
FREE Customer Support by telephone and email for the life of the instrument
For more information about the Teledyne API
family of monitoring instrumentation products,
call us or visit our website at
www. t e l e d y n e - a p i . c o m
9480 Carroll Park Drive San Diego, CA 92121-5201
Ph. 858-657-9800 Fax 858-657-9816
Email [email protected]
Ranges: 0-100 ppb to 0-10 ppm, user selectable.
Dual ranges and auto-ranging supported
Units: ppb, ppm, g/m
3
, mg/m
3
Zero Noise: < 0.3 ppb (RMS)
Span Noise: < 0.5% of reading above 100 ppb (RMS)
Lower Detectable Limit (LDL):< 0.6 ppb (RMS)
Zero Drift: < 1.0 ppb/24 hours, <1.0 ppb/7 days
Span Drift: <1% of reading/7 days
Lag Time: <10 seconds
Rise and Fall Time: < 20 seconds to 95%
Linearity: 1% of full scale
IZS Specifications (with optional reference feedback):
Flow Rate 800 cm
3
/min
Maximum Concentration 1.0 ppm
Minimum Concentration 0.050 ppm
Resolution 0.5 ppb
Repeatability (7 days) 1% of reading
Initial accuracy 5% of target
Sample Flow Rate: 800 cm
3
/min 10%
Operating Temperature
Range: 5 - 40C (with EPA Equivalency)
Dimensions (HxWxD): 7 (178 mm) x 17 (432 mm) x 23.5 (597
mm)
Weight: 28 lbs (12.7 kg); 30.6 lbs (13.8kg) with IZS
Power: 100V - 120V, 220V - 240V, 50/60 Hz, 250W
Analog Outputs: 10V, 5V, 1V, 100mV, selectable
Recorder Offset: 10%
Serial Outputs: Serial Port 1: RS-232 (DB-9M)
Serial Port 2: standard RS-232 or optional
RS-485 (DB-9F), Ethernet
Status (Digital): 8 outputs, 6 inputs (opto-isolated)
Current Output: Optional 4-20mA, select up to three
channels
Approvals: USEPA EQOA-0992-087
MCERTS certified Sira MC050070/00
EN14625 Approved, CE and others
NOTE: The values expressed above are in accordance with EPA
specifications. All error specifications are based on constant conditions.
Model 400E UV Absorption O
3
Analyzer
includes:
Standard two year warranty
Selectable voltage (specify below)
Internal pump
Auto ranging and dual ranges
47mm diameter particulate filter
8 isolated digital status outputs
Dual bi-directional RS-232
APIcom remote control software
Specify input AC voltage & frequency:
100V - 115V 50Hz
220V - 240V 60Hz
Specify output DC voltage:
10V 5V 1V 0.1V
Optional Equipment:
Rack mount brackets (19) with chassis slides
Rack mount brackets only
4-20mA output (specify up to three
channels)
Multi-drop serial interface
Ethernet port includes 7 ft. CAT-5 cable
(disables one serial port)
Calibration Options:
Valves for selection of customer-supplied
zero and span gas
i nternal zero air and span source for
calibration check
Reference adjustment feedback control
IZS ozone generator
Accessories:
RS-232 Cable
Expendables Kit
Spare Parts Kit
UV Absorption O
3
Analyzer
Schemati c
Speci fi cati ons
How to Order
MODEL 400E
Specifications subject to change without notice. Printed documents are uncontrolled. SAL000018 A (DCN 5058) M400E/08/08/08.

You might also like