Instructon Manua

HI 9126
Cabraton Check
Waterproof
pH/mV/C Meter
www.hannanst.com
Dear Customer,
Thank you for choosng a Hanna Instruments product.
Pease read ths nstructon manua carefuy before usng the
nstrument. Ths manua w provde you wth the necessary
nformaton for correct use of the nstrument, as we as a
precse dea of ts versatty. If you need addtona technca
nformaton, do not hestate to e-ma us at
[email protected].
WARRANTY
HI 9126 s guaranteed for two years aganst defects n
workmanshp and materas when used for ther ntended
purpose and mantaned accordng to nstructons. Eectrodes
and probes are guaranteed for sx months. Ths warranty s
mted to repar or repacement free of charge. Damage due to
accdents, msuse, tamperng or ack of prescrbed mantenance
s not covered.
If servce s requred, contact the deaer from whom you
purchased the
nstruments. If under warranty, report the mode number,
date of
purchase, sera number and the nature of the probem. If the
repar
s not covered by the warranty, you w be noted of the
charges
ncurred. If the nstruments are to be returned to Hanna
Instruments,
rst obtan a Returned Goods Authorzaton number from the
Technca
Servce department and then send t wth shppng costs
prepad.
When shppng any nstrument, make sure t s propery packed
for
compete protecton.
TABLE OF CONTENTS
WARRANTY...................................................2
PRELIMINARY EXAMINATION....................................3
GENERAL DESCRIPTION.........................................3
FUNCTIONAL DESCRIPTION.....................................4
SPECIFICATIONS...............................................5
OPERATIONAL GUIDE...........................................6
pH CALIBRATION............................................10
pH BUFFER TEMPERATURE DEPENDENCE..........................15
SETUP MENU................................................16
mV CALIBRATION............................................18
TEMPERATURE CALIBRATION....................................18
BATTERIES REPLACEMENT......................................19
LCD MESSAGE GUIDE..........................................21
TEMPERATURE CORRELATION FOR pH SENSITIVE GLASS............22
ELECTRODE CONDITIONING & MAINTENANCE.....................23
TROUBLESHOOTING GUIDE....................................25
ACCESSORIES................................................26
PRELIMINARY EXAMINATION
Remove the nstrument from the packng matera and examne t to
make sure that no damage has occurred durng shppng.
If there s any damage, notfy your deaer or the nearest Hanna
Customer Servce Center.
Each meter s supped wth:
HI 1230B combnaton doube-|uncton, ge pH eectrode
HI 7662 staness stee temperature probe wth 1 m (3.3) cabe
pH 4.01 & pH 7.01 buher soutons, 20 mL sachet
HI 700661 eectrode ceanng souton
100 mL pastc beaker
3 x 1.5V AAA Batteres
Instructon manua
Rugged carryng case
Note: Save a packng matera unt you are sure that the
nstrument
functons correcty. A defectve tems must be returned n
the
orgna packng wth the supped accessores.
GENERAL DESCRIPTION
HI 9126 s a state-of-the-art waterproof, heavy-duty pH meter
desgned
to provde aboratory resuts and accuracy under harsh ndustra
condtons.
A arge mut-eve LCD, wth cear ndcatons reated to the
eectrode and nstrument status, pH and temperature dspayed
smutaneousy, and user frendy graphc symbos durng
cabraton.TION
Ths meter s provded wth a seres of new dagnostc features whch
add an entrey new dmenson to pH measurement, by aowng the
user to dramatcay mprove the reabty of the measurement:
7 memorzed buhers (pH 1.68, 4.01, 6.86, 7.01, 9.18, 10.01
and 12.45) for cabraton
Custom cabraton (up to two custom buhers)
Messages on the LCD to make the cabraton easy and accurate
Dagnostc features to aert the user when the eectrode needs ceanng
Montorng of the eectrode agng
User-seectabe "cabraton tme-out" to remnd you when a
new
cabraton s necessary
HI 9126 can aso measure for Oxdaton Reducton Potenta n the
mV range wth a resouton of 0.1 mV.
It ohers an extended temperature range from -20 C (-4 F) to
120 C (248 F).
3
FUNCTIONAL DESCRIPTION
1) Lqud Crysta Dspay (LCD).
2) RANGE key, to seect pH or mV.
3) ON/OFF key, to turn the meter ON and OFF.
4) CAL key, to enter or ext cabraton mode.
5) SETUP/CFM key, to enter SETUP mode or to conrm
cabraton. 6) Battery compartment cap.
7) Temperature probe socket.
SPECIFICATIONS
-2.00 to 16.00 pH
RANGE 699.9 mV / 1999 mV
-20.0 to 120.0 C (-4.0 to 248.0 F)
0.01 pH
RESOLUTION 0.1 mV / 1 mV
0.1 C (0.1 F)
0.01 pH
ACCURACY 0.2 mV / 1 mV
@ 20 C / 68 F
0.4 C (0.8 F)
(excudng probe error)
0.02 pH
Typca EMC Devaton 0.2 mV / 1 mV
0.4 C (0.8 F)
1 or 2-pont, wth 7 memorzed buhers
pH Cabraton (pH 1.68, 4.01, 6.86, 7.01, 9.18,
10.01, 12.45) and 2 custom buhers
Ohset Cabraton 1 pH
Sope Cabraton From 80 to 108%
Automatc, from -20.0 to 120.0 C (
Temperature Compensaton -4.0 to 248.0 F) or manua
wthout temperature probe
pH Eectrode HI 1230B (ncuded)
Temperature Probe HI 7662 (ncuded)
Input Impedance 10
12
ohms
3 x 1.5V AAA sze batteres
approx. 200 hours of contnuous use
8) BNC eectrode connector.
9) MR/CUST BUF key, to reca the stored vaue from memory or
to enter custom buher vaues.
10) MEM/CLR key, to store the readng n memory or to cear
cabraton.
11) and keys, for manua temperature settng, enterng
menu parameters or changng buher vaue.
12) LIGHT key, togge to swtch the dspay backght on and
oh. 13) Secondary dspay.
14) Prmary dspay.
4
Battery Type & Lfe
Auto-oh
Dmensons
Weght
Envronment
Warranty
wthout backght (50 hours wth
backght)
User seectabe: 20 mnutes or dsabed
185 x 72 x 36 mm (7.3 x 2.8 x 1.4")
300 g (10.6 oz.)
0 - 50 C (32 - 122 F)
max RH 100%
2 years
5
OPERATIONAL GUIDE
INITIAL PREPARATION
The meter s supped wth batteres (for detas see page 19).
To prepare the nstrument for use, connect the pH eectrode
and the temperature probe to the BNC and temperature sockets
on the top of the nstrument. The temperature probe can be
used ndependenty to take temperature measurements, or t
can be used n con|uncton wth the pH eectrode to utze the
meter's Automatc Temperature Compensaton (ATC) mode. If
the probe s dsconnected, temperature can aso be set manuay
wth the ARROW keys.
Turn the nstrument ON by pressng ON/OFF.
At start-up the dspay w show a LCD segments and then
the battery percentage whe the nstrument performs a sef
check (or as ong as the button s hed).
The meter w automatcay enter measurement mode.
After measurement swtch the meter oh. Cean the eectrode and
store t wth a few drops of HI 70300 storage souton n the
protectve cap. To save the batteres, the auto-oh feature
turns the meter oh after 20 mnutes (no button pressed). To
dsabe ths feature, see "Setup Menu" secton on page 16.
pH MEASUREMENTS
To take a pH measurement remove the
eectrode
The LCD w show the pH measurement and the temperature of
the
sampe.
In order to take more accurate pH measurements, make sure that
the nstrument s cabrated (see page 10 for detas).
The gass bub and the |uncton on your eectrode shoud aways be
most, never aow t to dry out.
If severa measurements are taken successvey n dherent
sampes, rnse the eectrode thoroughy wth deonzed or tap
water and a sma amount of the sampe to be measured.
The pH readng s drecty ahected by temperature. In order for the
meter
to measure the pH accuratey, temperature must be compensated
for. If
the sampe temperature s dherent from the temperature at whch
the pH
eectrode was kept, aow a few mnutes for therma equbraton.
To use the meter's Automatc Temperature Compensaton feature,
submerse the temperature probe nto the sampe as cose to
the eectrode as possbe and wat for a few mnutes.
If manua temperature compensaton s desred the temperature
probe must be dsconnected from the nstrument.
The dspay w show the defaut temperature of 25 C, or the ast
temperature set the "C" (or "F") ndcator w bnk.
The temperature can now be ad|usted wth the ARROW keys.
protectve cap and submerse the eectrode
and the temperature probe 3 cm (1V")
nto the sampe and str genty.
If necessary, press the RANGE key unt
the dspay shows pH mode.
Aow tme for the readng to stabze.
6
3 cm
(1V")
7
ORP MEASUREMENTS
To perform ORP measurements, connect an optona ORP
eectrode (see "Accessores" secton) to the meter and turn t
ON.
If necessary, enter the "mV" mode by pressng RANGE.
Submerse the ORP eectrode 3 cm (1V") nto the sampe to be
tested and wat for the readng to stabze.
Measurements wthn the 699.9 mV range are dspayed wth
0.1 mV resouton, whe outsde ths range the resouton s 1 mV.
The ATC (or MTC) key s turned oh because the mV readngs are
not temperature compensated.
For accurate ORP measurements, the surface of the eectrode
must be
cean and smooth. Pretreatment soutons are avaabe to
condton
the eectrode and mprove the response tme (see "Accessores"
secton).
Notes:
When the readng s out of range, the dspay w ash the
cosest
fu-scae vaue.
If usng a pH eectrode whe n mV mode, the meter w
measure
the mV generated by the pH eectrode.
MEM & MR FUNCTIONS
Pressng the MEM key w memorze the readng on the dspay
and store t n the nterna memory. The pH (mV) and
temperature, eectrode condton and the buhers used for
cabraton w be stored. The "MEMORIZE" tag bnks and the
dspay remans frozen unt the MEM key s pressed agan.
8
Note: Whe n MEM mode, the user can swtch between pH and
mV
by pressng the RANGE key.
A stored vaue can be recaed by pressng MR: the dspay w
show the memorzed readng and the "RECALL MEMORIZED"
tag, as ong as the MR key s pressed.
Note: MR w ony dspay the range that was actve when MEM
was
pressed.
BACKLIGHT FEATURE
The meter s provded wth a Backght feature,
whch can be easy accessed through the LIGHT
key.
Note: The backght automatcay shuts oh after approxmatey 1
mnute
of nonuse.
9
pH CALIBRATION
It s recommended to cabrate the nstrument frequenty, f
hgh accuracy s requred.
The nstrument shoud be recabrated:
Whenever the pH eectrode s repaced.
At east once a week.
After testng aggressve chemcas.
When extreme accuracy s requred.
When the cabraton tme-out s expred (f feature s
enabed). PROCEDURE
The meter ohers a choce of 7 memorzed buhers (1.68, 4.01, 6.86,
7.01, 9.18, 10.01 and 12.45 pH) and two user dened vaues,
C1
and C2 (see "Custom Buher Seecton" secton on page 12 for
detas).
Pour a sma quantty of seected buher soutons nto cean beakers.
For accurate cabraton use two beakers for each buher
souton, the
rst one for rnsng the eectrode and the second one for
cabraton.
Remove the protectve cap and rnse the eectrode wth some of
the buher souton to be used for the rst cabraton
pont. TWO-POINT CALIBRATION
Press the CAL key. The "CAL" and " " ndcators w
be
dspayed. The secondary LCD w dspay buher "7.01". If
a
dherent cabraton buher s desred (e.g. "6.86"), use
the ARROW keys to change the dspayed vaue.
Submerse the eectrode approxmatey 3 cm (1V") nto the
souton, pace the temperature probe as cose as possbe to the
eectrode and str genty.
The LCD w ash "WAIT
NOT
READY" for 12 seconds, then:
f the readng s not cose to
the
seected buher, "WRONG " and
"WRONG " w bnk
aternatvey;
f t s cose to the seected buher
the
meter w advse the user wth
an
10
audbe sgna (f enabed) when the readng becomes stabe
and the dspay w change to "READY" and bnkng "CFM".
Press the CFM key to conrm the cabraton: the meter stores the
rst cabraton pont; the prmary LCD w show the cabrated
readng, whe the secondary LCD w show the second buher to
be used for cabraton ("pH 4.01").
If youre gong to cabrate wth a dherent buher, seect
the desred vaue by pressng the arrow keys.
Note: The meter automatcay skps the buher used for the rst
cabraton
pont to avod erroneous procedure. A dherence of at east 1.5
pH
unt s requred between the two buhers: once cabrated at
ether pH 7.01 or 6.86, the nstrument automatcay gnores
the other vaue for the second pont (same for pH 10.01 and
9.18).
Submerse the eectrode approxmatey 3 cm (1V") nto the
second buher souton, pace the temperature probe as cose
as possbe to the eectrode and str genty.
The LCD w ash "WAIT NOT READY" for 12 seconds, then:
f the readng s not cose to the
seected buher, "WRONG " and
"WRONG " w bnk aternatvey;
f t s cose to the seected buher the
meter
w advse the user wth an audbe
sgna (f enabed) when the readng
becomes stabe and the dspay w change
to "READY" and bnkng "CFM".
Press the CFM key: the vaue s stored n memory and the meter
returns to measurement mode. The tags correspondng to the
buhers used for cabraton and the "condton" bargraph (f
enabed) w be ght up.
11
Note: To ncrease the speed, contnuousy press the ARROW keys.
Note: Durng cabraton, the secondary LCD shows the seected
buher
vaue; press RANGE to dspay the buher temperature.
Note: To cear a prevous cabraton and return to the defaut
vaues, press CLR at any tme after enterng the
cabraton mode. The LCD w show "CLr CAL" for one
second, and then w return to norma measurement
mode.
The LCD w show an empty bargraph to warn the user
that the meter s not cabrated.
ONE-POINT CALIBRATION
For optmum accuracy t s aways recommended to perform a
two-
pont cabraton, but for a faster operaton t s aso possbe
to carry out a snge-pont cabraton.
pH 7.01 or pH 6.86 (NIST) are typcay used, however the meter
can be cabrated wth any of the memorzed cabraton vaues.
After cabratng the rst pont (see two-pont cabraton), press
the CAL key to end the cabraton procedure.
Note: Wth one-pont cabraton eectrode "condton" s not
avaabe
and ony the frame s shown. Cabraton tme-out s actve.
CUSTOM BUFFER SELECTION
The meter aows the user to cabrate wth custom buhers.
To seect a custom buher press the CUST BUF key whe n cabraton
mode. Use the arrow keys to set the desred vaue for C1 (the
defaut vaue s 7.00).
12
Once the desred vaue s reached,
press CFM to conrm the vaue. The
meter w contnue cabraton as
wth memorzed buhers.
The meter w dspay "C2". Use the
arrow keys to change the vaue of
the second custom buher, or press
CUST BUF to seect a memorzed
buher.
EXPIRED CALIBRATION
The nstrument has a rea tme cock (RTC), n order to montor the
tme eapsed snce the ast pH cabraton.
The rea tme cock s reset every tme the meter s cabrated
and the "expred cabraton" status s trggered when the meter
detects a cabraton tme-out. The CAL tag w start bnkng to
warn the user that the meter shoud be recabrated.
The cabraton tme-out can be set (see "Setup menu" secton
on page 14) from 0 (functon dsabed) to 14 days.
For exampe, f a 4 days tme-out has been seected the meter w
ssue the aarm exacty 4 days after the ast cabraton.
If the expraton vaue s changed (e.g. to 7 days), then the aarm
w be mmedatey recacuated and appear 7 days after the
ast
cabraton.
Notes:
When the meter s not cabrated or cabraton s ceared
(defaut
vaues oaded) there s no "expred cabraton", and the dspay
aways shows a bnkng CAL tag.
When an abnorma condton n the RTC s detected the
meter
forces the "expred cabraton" status.
13
CONDITION
The dspay s provded wth a 5-dot bargraph (uness
dsabed)
whch gves an ndcaton of the eectrode status after cabraton:
Bargraph ndcaton Condton vaue
A 5 dots steady 81 to 100% of fe
4 dots steady 61 to 80%
3 dots steady 41 to 60%
2 dots steady 21 to 40%
1 dot steady 1 to 20%
1 dot bnkng 0%
Ony frame s ON No nfo avaabe
The "condton" bargraph remans actve for 12 hours after
cabraton, then ony the frame s shown.
Note: When an abnorma condton n the RTC s detected, the
"condton"
s ceared and ony the bargraph frame s shown on the
dspay.
CLEAN ELECTRODE
Each tme pH cabraton s performed, the meter nternay
compares the new cabraton wth the one prevousy stored.
When ths comparson ndcates a
sgncant
dherence, the "CLEAN ELECTRODE"
message bnks on the LCD to advse
the
user that the pH eectrode may need
to
be ceaned (see "Eectrode
Condtonng &
Mantenance" secton).
After ceanng, perform cabraton.
Note: If the cabraton data are ceared, the comparson s
done
wth the defaut vaues.
14
pH BUFFER TEMPERATURE
DEPENDENCE
The temperature has an ehect on pH. The cabraton buher
soutons
are ahected by temperature changes to a esser degree than
norma
soutons. Durng cabraton the nstrument w automatcay
cabrate
to the pH vaue correspondng to the measured or set
temperature.
TEMP pH BUFFERS
C F 1.68 4.01 6.86 7.01 9.18 10.01 12.45
0 32 1.67 4.01 6.98 7.13 9.46 10.32 13.38
5 41 1.67 4.00 6.95 7.10 9.39 10.24 13.18
10 50 1.67 4.00 6.92 7.07 9.33 10.18 12.99
15 59 1.67 4.00 6.90 7.05 9.27 10.12 12.80
20 68 1.68 4.00 6.88 7.03 9.22 10.06 12.62
25 77 1.68 4.01 6.86 7.01 9.18 10.01 12.45
30 86 1.68 4.02 6.85 7.00 9.14 9.96 12.29
35 95 1.69 4.03 6.84 6.99 9.11 9.92 12.13
40 104 1.69 4.04 6.84 6.98 9.07 9.88 11.98
45 113 1.70 4.05 6.83 6.98 9.04 9.85 11.83
50 122 1.71 4.06 6.83 6.98 9.01 9.82 11.70
55 131 1.72 4.08 6.84 6.98 8.99 9.79 11.57
60 140 1.72 4.09 6.84 6.98 8.97 9.77 11.44
65 149 1.73 4.11 6.84 6.99 8.95 9.76 11.32
70 158 1.74 4.12 6.85 6.99 8.93 9.75 11.21
75 167 1.76 4.14 6.86 7.00 8.91 9.74 11.10
80 176 1.77 4.16 6.87 7.01 8.89 9.74 11.00
85 185 1.78 4.17 6.87 7.02 8.87 9.74 10.91
90 194 1.79 4.19 6.88 7.03 8.85 9.75 10.82
95 203 1.81 4.20 6.89 7.04 8.83 9.76 10.73
Durng cabraton the nstrument w dspay the pH buher vaue at
25 C.
15
SETUP MENU
The nstrument aows the user to congure severa
parameters through the Setup Menu.
To enter the Setup Menu, whe n measurement mode, press
and hod the SETUP key for about 5 seconds.
Once the menu s entered, each parameter can be changed by
usng the arrow keys; then pressng the CFM key w conrm the
vaue and scro to the next parameter.
1. Audbe sgna: On (defaut) or Oh
2. Auto-oh feature: 20 mnutes (defaut) or dsabed
3. Temperature measure unt: C (defaut) or F
16
4. Cabraton segments: On (defaut) or Oh. Ths enabes or
dsabes
the bargraph, the "CLEAN ELECTRODE" message and the buher
segments.
5. Cabraton tme-out: 1 (defaut) to 14 days or dsabed (0 days)
After the ast parameter, press the CFM key to conrm the settng
and return to measurement mode.
17
mV CALIBRATION
HI 9126 has been precabrated for mV range at the factory. For
optmum accuracy, t s recommended to recabrate the meter
for mV readngs at east once a year. Contact your Deaer or the
nearest Hanna Customer Servce Center for more nformaton.
TEMPERATURE CALIBRATION
HI 9126 has beenprecabrated for temperature at the factory.
For optmum accuracy, t s recommended to recabrate the
meter for temperature at east once a year. Contact your
Deaer or the nearest Hanna Customer Servce Center for more
nformaton.
18
BATTERIES REPLACEMENT
The nstrument s supped wth batteres. Frst tme you start
workng wth the nstrument, nsert the supped batteres n
the battery compartment observng the correct poarty (see
page 20).
At start-up the battery percentage s dspayed.
If the batteres become weak, the dspay w ash the
battery symbo to advse the user that approxmatey 1 hour of
workng tme remans. It s recommended to change the batteres
as soon as the battery symbo appears bnkng.
The meter s aso provded wth the BEPS (Battery Error Preventon
System) feature whch automatcay turns the nstrument oh
when
the battery eve s too ow to ensure reabe readngs. At start-
up the
dspay w show "0 batt" for few seconds, then the meter
automatcay
turns oh.
19
To repace the batteres, foow the next steps:
LCD MESSAGE GUIDE
Turn OFF the nstrument.
Open the battery compartment cap (ocated on the top of the TAGS & SYMBOLS
nstrument).
Remove od batteres.
Insert three new 1.5V AAA batteres n the battery
compartment,
observng the poarty on the rear of the nstrument.
Reattach the battery compartment cap.
Mode tags ght up for ndcatng the correspondng actve mode,
and bnk for warnng the user.
SETUP on: setup menu mode has been entered.
MEASURE on: measurement mode.
CALIBRATION on: cabraton mode has been entered.
MEMORIZE on: measurement stored n the nterna memory and
frozen on the dspay
RECALL MEMORIZED on: stored vaue recaed.
Indcaton of temperature compensaton mode:
MTC for manua, ATC for automatc compensaton.
Battery symbo bnkng: ow battery condton. Batteres shoud
be repaced.
Cabraton messages.
WAIT NOT READY bnkng: buher has been recognzed, but
readng s not stabe.
READY on: buher has been recognzed and readng s stabe.
WRONG and WRONG bnkng aternatvey: wrong buher,
vaue not recognzed.
CLEAN ELECTRODE bnkng: an abnorma dherence between
new and prevous cabraton has been detected. Eectrode
ceanng s suggested. Foow the ceanng procedure descrbed
n the "Eectrode condtonng & mantenance" secton. If the
probem remans, check the buher soutons.
20 21
TEMPERATURE CORRELATION
FOR pH SENSITIVE GLASS
The resstance of gass eectrodes partay depends on the
temperature.
The ower the temperature, the hgher the resstance. It takes
more tme
for the readng to stabze f the resstance s hgher. In
addton, the
response tme w suher to a greater degree at temperatures
beow 25 C.
Snce the resstance of the pH eectrode s n the range of 50 -
200
Mohms, the current across the membrane s n the pco Ampere
range.
Large currents can dsturb the cabraton of the eectrode for
many
hours.
For these reasons hgh humdty envronments, short crcuts
and statc dscharges can be detrmenta to a stabe pH
readng.
The pH eectrodes fe aso depends on the temperature. If
constanty
used at hgh temperatures, the eectrode fe s drastcay
reduced.
Typca Eectrode Lfe
Ambent Temperature 1 - 3 years
90 C Less than 4 months
120 C Less than 1 month
Akane Error
Hgh concentratons of sodum ons nterfere wth readngs n
akane soutons. The pH at whch the nterference starts to be
sgncant depends upon the composton of the gass. Ths
nterference s caed akane error and causes the pH to be
underestmated. Hannas gass formuatons have the ndcated
characterstcs.
Sodum Ion Correcton for Gass at 20-25 C
Concentraton pH Error
0.1 Mo L
-1
Na
+
13.00 0.10
13.50 0.14
14.00 0.20
12.50 0.10
13.00 0.18
1.0 Mo L
-1
Na
+
13.50 0.29
14.00 0.40
22
ELECTRODE CONDITIONING & MAINTENANCE
Not present n ge eectrodes.
PREPARATION PROCEDURE
Remove the eectrode protectve cap.
DO NOT BE ALARMED IF ANY SALT DEPOSITS ARE PRESENT. Ths s
norma wth eectrodes and they w dsappear when rnsed wth
water. Durng transport tny bubbes of ar may have formed
nsde the gass bub. The eectrode cannot functon propery
under these condtons. These bubbes can be removed by "shakng
down" the eectrode as you woud do wth a gass thermometer.
If the bub and/or |uncton are dry, soak the eectrode n HI 70300
Storage Souton for at east one hour.
23
For reabe eectrodes, f the re souton (eectroyte) s
more than
2 cm (1") beow the hoe, add the approprate Eectroyte
Souton.
MEASUREMENT
Rnse the eectrode tp wth dsted water, submerse t 3 cm
(1V") n the sampe and str genty for a few seconds.
For a faster response and to avod cross contamnaton of the
sampes, rnse the eectrode tp wth the souton to be tested,
before takng any measurements.
STORAGE PROCEDURE
To mnmze coggng and ensure a quck response tme, the
gass bub and the |uncton shoud aways be kept most.
When not n use, store t wth a few drops of HI 70300
storage souton n the protectve cap.
NEVER STORE THE ELECTRODE IN DISTILLED OR DEIONIZED
WATER.
PERIODIC MAINTENANCE
Inspect eectrode and cabe. The cabe must be ntact. No
cracks shoud be seen on the eectrode stem or bub. If any
scratches or cracks are present, repace the eectrode. Rnse oh
any sat deposts wth water. Connectors must be perfecty cean
and dry.
For reabe eectrodes:
Re the eectrode wth fresh eectroyte (see the eectrodes
speccatons to seect the correct reng souton). Aow the
eectrode to stand uprght for 1 hour. Foow the Storage
Procedure above.
CLEANING PROCEDURE
Genera Soak n Hanna HI 7061 Genera Ceanng
Souton for approxmatey hour.
Proten Soak n Hanna HI 7073 Proten Ceanng
Souton for 15 mn.
Inorganc Soak n Hanna HI 7074 Inorganc
CeanngSouton for 15 mn.
O/grease Rnse wth Hanna HI 7077 O & Fat Ceanng
Souton for 1 mn.
IMPORTANT: After performng any of the ceanng procedures,
rnse
the eectrode thoroughy wth dsted water and soak t n HI
70300
Storage Souton for at east 1 hour before takng
measurements.
24
TROUBLESHOOTING GUIDE
SYMPTOMS PROBLEM SOLUTION
Sow reponse/excessve Drty pH eectrode. The eectrode needs to be
drft. cean.
Foow the Ceanng
Procedure on page 24.
Readng uctuates up Cogged/drty |uncton. Cean the eectrode.
and down (nose). Low eectroyte eve Re wth fresh eectroyte
(reabe eectrodes (reabe eectrodes ony).
ony). Check cabe and
connector.
Dspay shows Readng out of Make sure the eectrode s
bnkng fu scae range. connected.
vaue. Check that sampe s
wthn measurabe range;
Check eectroyte eve and
genera eectrode status.
mV scae out of Dry membrane or dry Soak eectrode n HI 70300
range. |uncton. storage souton for at east
30 mnutes.
Check cabe and connector.
Dspay shows Broken temperature Repace temperature
bnkng "C" or "F". probe. probe.
Dspay shows Dherence between Cean eectrode and
"CLEAN ELECTRODE new and prevous recabrate. If the probem
" bnkng. cabraton has been remans, check the buher
detected. soutons.
Dspay shows Low battery eve. Repace the batteres.
bnkng battery
symbo.
Meter does not work Broken temperature Repace temperature
wth temperature probe. probe.
probe. Wrong temperature
probe used.
Meter fas to cabrate Broken pH eectrode. Repace eectrode.
or gves fauty
readngs.
"WRONG Wrong or Check that buher souton
CALIBRATION" s contamnated buher. s correct and fresh.
dspayed durng pH
cabraton procedure.
Meter shuts oh. Dead batteres or Repace the batteres.
Auto-oh feature s Press ON/OFF.
enabed: n ths case,
meter shuts oh after
20 mn of non-use.
"Er0", "Er1", "Er2" EEPROM error. Contact your deaer or any
message at start up. Hanna Servce Center.
"Cr" message at start Loaded defaut pH Perform pH cabraton.
up. cabraton vaues.
25
ACCESSORIES
pH CALIBRATION SOLUTIONS
HI 70004P pH 4.01 Buher Souton, 20 mL sachet, 25 pcs
HI 70007P pH 7.01 Buher Souton, 20 mL sachet, 25
pcs HI 70010P pH 10.01 Buher Souton, 20 mL sachet,
25 pcs
HI 7004L pH 4.01 Buher Souton, 500 mL botte
HI 7004M pH 4.01 Buher Souton, 230 mL botte
HI 7006L pH 6.86 Buher Souton, 500 mL
botte
HI 7006M pH 6.86 Buher Souton, 230 mL
botte
HI 7007M pH 7.01 Buher Souton, 500 mL
botte
HI 7007M pH 7.01 Buher Souton, 230 mL
botte
HI 7009L pH 9.18 Buher Souton, 500 mL
botte
HI 7009M pH 9.18 Buher Souton, 230 mL
botte
HI 7010L pH 10.01 Buher Souton, 500 mL
botte HI 7010M pH 10.01 Buher Souton, 230
mL botte ELECTRODE STORAGE SOLUTION
HI 70300L Storage Souton, 500 mL
botte HI 70300M Storage Souton, 230
mL botte ELECTRODE CLEANING
SOLUTIONS
HI 70000P Eectrode Rnse Souton, 20 mL sachet, 25
pcs
HI 7061L Genera Ceanng Souton, 500 mL botte
HI 7061M Genera Ceanng Souton, 230 mL botte
HI 7073L Proten Ceanng Souton, 500 mL
botte
HI 7073M Proten Ceanng Souton, 230 mL
botte
HI 7074L Inorganc Ceanng Souton, 500 mL
botte
HI 7074M Inorganc Ceanng Souton, 230 mL
botte
HI 7077L O & Fat Ceanng Souton, 500 mL
botte
HI 7077M O & Fat Ceanng Souton, 230 mL
botte
REFILLING ELECTROLYTE SOLUTIONS (50 mL, 4 pcs)
HI 7071 3.5M KC+AgC Eectroyte for snge |uncton eectrodes
HI 7072 1M KNO3 Eectroyte
HI 7082 3.5M KC Eectroyte for doube |uncton eectrodes
HI 8093 1M KC+AgC Eectroyte
ORP PRETREATMENT SOLUTIONS
HI 7091L Reducng Pretreatment Souton, 500 mL
botte
HI 7091M Reducng Pretreatment Souton, 230 mL
botte
HI 7092L Oxdzng Pretreatment Souton, 500 mL
botte HI 7092M Oxdzng Pretreatment Souton, 230
mL botte ORP SOLUTIONS
HI 7020L Test Souton 200-275 mV, 500 mL botte
HI 7020M Test Souton 200-275 mV, 230 mL botte
HI 7021L Test
Souton 240 mV, 500 mL
botte
HI 7021M Test
Souton 240 mV, 230
mL botte
26
HI 7022L Test Souton 470 mV, 500 mL botte HI 7022M Test
Souton 470 mV, 230 mL botte pH ELECTRODES
A eectrodes part numbers endng n B are supped wth a BNC connector and 1 m (3.3')
cabe, as shown beow:
HI 1043B
Gass-body, doube |uncton, reabe, combnaton pH eectrode. Use: strong
acd/aka.
9.5mm DIA 12 mm
0.37" 0.5"
HI 1043
120 mm
4.7"
HI 1053B
Gass-body, trpe ceramc, conc shape, reabe, combnaton pH eectrode.
Use: emusons.
12 mm
0.5"
HI 1053
120 mm
4.7"
HI 1083B
Gass-body, mcro, Vscoene, non-reabe, combnaton pH eectrode. Use: botechnoogy,
mcro ttraton.
12 mm
0.5" 5 mm 3 mm
0.2" 0.12" 3.0 mm DIA0.12"
HI 1083
120 mm4.7"
HI 1131B
Gass-body, snge |uncton, reabe, combnaton pH eectrode. Use: genera
purpose.
9.5mm DIA 12 mm
0.37" 0.5"
HI 1131
120 mm
4.7"
27
HI 1330B
Gass-body, semmcro, snge |uncton, reabe, combnaton
pH eectrode.
Use: aboratory, vas.
5mm DIA 5mm
0.2" 0.2"
HI 1330
120 mm
4.7"
HI 1331B
Gass-body, semmcro, snge |uncton, reabe, combnaton
pH eectrode.
Use: asks.
8 mm 7.5mm DIA
0.3" 0.29"
HI 1331
210 mm
8.25"
HI 1230B
Pastc-body (PES), doube |uncton, ge-ed, combnaton
pH
eectrode.
Use: genera, ed.
12 mm
0.5"
HI 1230
120 mm
4.7"
HI 2031B
Gass-body, semmcro, conc, reabe, combnaton pH
eectrode. Use: semsod products.
6 mm
0.25"
HI 2031
75 mm
2.95"
HI 1332B
Pastc-body (PES), doube |uncton, reabe, combnaton
pH
eectrode.
Use: genera purpose.
12 mm
0.5"
HI 1332
120 mm
4.7"
28
FC 100B
Pastc-body (PVDF), doube |uncton, reabe, combnaton pH
eectrode. Use: genera purpose for food ndustry.
12 mm
0.5"
FC 100
120 mm
4.7"
FC 200B
Pastc-body (PVDF), open |uncton, conc, Vscoene, non-
reabe, combnaton pH eectrode.
Use: meat & cheese.
6 mm
0.25"
FC 200
75 mm
2.95"
FC 210B
Gass-body, doube |uncton, conc, Vscoene, non-reabe,
combnaton pH eectrode.
Use: mk, yogurt.
12 mm
0.5"
FC 210
120 mm
4.7"
FC 220B
Gass-body, trpe-ceramc, snge |uncton, reabe,
combnaton pH eectrode.
Use: food processng.
9.5mm DIA 12 mm
0.37" 0.5"
FC 220
120 mm
4.7"
FC 911B
Pastc-body (PVDF), doube |uncton, reabe wth but-n
amper, combnaton pH eectrode. Use: very hgh humdty.
12 mm0.5"
FC 911
110 mm
4.3"
29
HI 1413B
Gass-body, snge |uncton, at tp, Vscoene, non-reabe,
combnaton pH eectrode. Use: surface measurement.
12 mm
0.5"
HI 1413
110 mm
4.3"
ORP ELECTRODES
HI 3131B
Gass-body, reabe, combnaton patnum ORP
eectrode. Use: ttraton.
12 mm
0.5"
HI 3131
150 mm5.9"
HI 3230B
Pastc-body (PES), ge-ed, combnaton patnum ORP
eectrode. Use: genera purpose.
12 mm
0.5"
HI 3230
120 mm
4.7"
HI 4430B
Pastc-body (PES), ge-ed, combnaton god ORP
eectrode. Use: genera purpose.
12 mm
0.5"
HI 4430
120 mm
4.7"
Consut the Hanna Genera Cataog for a compete and wde
seecton of eectrodes.
OTHER ACCESSORIES
HI 721317 Rugged carryng case
HI 740157 Pastc eectrode reng ppet (20 pcs)
HI 76405 Eectrode hoder
HI 7662 Temperature probe wth 1 m (3.3') screened cabe
HI 8427 pH and ORP eectrode smuator wth 1 m (3.3')
coaxa cabe endng n femae BNC connectors
HI 931001 pH and ORP eectrode smuator wth LCD and 1 m
(3.3') coaxa cabe endng n femae BNC
connectors
30
RECOMMENDATIONS FOR USERS
Before usng these products, make sure they are entrey sutabe
for the envronment n whch they are used.
Operaton of these nstruments n resdenta areas coud cause
unacceptabe nterferences to rado and TV equpment, requrng
the operator to foow a necessary steps to correct nterferences.
The gass bub at the end of the pH eectrode s senstve
to eectrostatc dscharges. Avod touchng ths gass bub at a
tmes. Durng operaton, ESD wrst straps shoud be worn to
avod possbe damage to the eectrode by eectrostatc
dscharges.
Any varaton ntroduced by the user to the supped equpment
may degrade the nstruments EMC performance.
To avod eectrca shock, do not use these nstruments when
votages at the measurement surface exceed 24 VAC or 60 VDC.
To avod damage or burns, do not perform any measurement n
mcrowave ovens.
Hanna Instruments reserves the rght to modfy the desgn,
constructon and appearance of ts products wthout advance
notce.
Hanna Instruments Inc.
Hghand Industra Park
584 Park East Drve
Woonsocket, RI 02895 USA
Technca Support for Customers
Te. (800) 426 6287
Fax (401) 765 7575
E-ma [email protected]
www.hannanst.com
Loca Saes and Customer Servce Omce
Prnted n EUROPE
(ROMANIA) MAN9126Y 09/10