Scribd
Upload
315 views

Help Optimization Parameters

This document discusses various radio network optimization parameters in 3G mobile networks. It covers topics like offset configuration, carrier to interference ratios, congestion levels, handover parameters, radio link parameters and adaptive modulation and coding settings. The goal is to optimize network performance by fine-tuning these radio resource management settings based on traffic patterns and coverage needs.

Uploaded by

عبدالرحمن دقداق
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
315 views

Help Optimization Parameters

This document discusses various radio network optimization parameters in 3G mobile networks. It covers topics like offset configuration, carrier to interference ratios, congestion levels, handover parameters, radio link parameters and adaptive modulation and coding settings. The goal is to optimize network performance by fine-tuning these radio resource management settings based on traffic patterns and coverage needs.

Uploaded by

عبدالرحمن دقداق
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 4

http://fr.scribd.

com/doc/137526574/Ericsson-Features
Offset____________________________________________
Offset with cong to cell high HO att and no cong
cell cellr offsetN
high cong no cong
high Ho attempt
HOSR>99
RANKn = SS_DLn - OFFSETn,s - HYSTn
CLS_______________________________________________
LSSTATE BSC ACTIVE
check per neighbour handover success rate and only then optimise CLS settings
nbr belonging same BSC
nbr same Layer
Idle TCH=<CLSLEVEL 15
Idle TCH/F>CLSACC 25
GPRSPRIO in BSC if PDCH idle or busy
For the cell with high load [TCH cong > 2% & DTHNAMR =100]
CLSSTATE=Active
CLSLEVEL =15
RHYST=100
CLSRAMP=8
and for the neighbour [TCH cong < 2% & DTHNAMR < 50]
HOCLSACC=On
CLSACC = 25.
HCS ----------------------------------------------
HCSBANDTHR= -95 dbm
900 GSM Macro (Layer=8, LYTRH= -75 dBm)
900 GSM micro (Layer=6, LYTRH= -75 dBm) for coverage
1800 GSM macro (Layer=3, LYTRH= -75 dBm)
1800 GSM micro (Layer=1, LYTRH= -75 dBm) for capacity
1800 > 1
900 > 2
HCSTRAFDISSTATE Over BSC
in HO allow tch avail>= HCSIN 30
out HO allow tch avail <= HCSOUT 50
FASTMSREG HO>NHO in THO MS Directed to higher layer
Assignment to other cell--------------------------------
MSC: HNDSDCCHTCH:(1) controls whether an intra-MSC inter-BSC
BSC: Assoc=ON
IBHOASS=ON to other BSC
Better cell (Quality)-----------------------------
Assoc=ON
SSEVALSI=6 to 9
SSRAMPSI=1
Worse cell (Congestion)--------------------------
Check per neighbour handover success rate before implementing this feature.
AW=ON assignment to a worse cell is allowed from that cell
AWOFFSET=3 ( no congestion)
5 congestion
20 no interference
SS+AWOFFSET
MS measures SS(serving) =-70,AWOFFSET=15 allows assignment to neighbour with SS=
-85 or stronger
Relation
CAND=BOTH
IHO --------------------------------------------------
MAXIHO=2 hop
3 no hop
TMAXIHO=7
TIHO=10
rxqual-ul > QOFFSETUL + FQSS(RXLEV_UL + SSOFFSETUL)
rxqual-dl > QOFFSETDL + FQSS(RXLEV_DL + SSOFFSETDL)
QOFFSETULN=13 (due to bad uplink quality)
increase nbr of UL att
decrease nbr of DL att
IRC ----------------------------------------------------
ICM4&5_TCH
TCH Drop Reason, Bad Quality Uplink
TRX DTRU
RXD=AB
Power Control ----------------------------------------
DL UL AMR
SSDESDL = 90 92 92 94
QDESDL = 30 30 40 40
LCOMPDL = 10 6 6 6
QCOMPDL = 60 60 60 60
Half rate tuning -------------------------------------
TCH Traffic
Average Number of available TCH roundup
TCONGSAS
TCONGSHO
TMSESTB
wasted traffic=TCH Traffic*(TCONGSAS+TCONGSHO)/TMSESTB
Total Traffic=wasted Traffic+TCH traffic roundup
Amended Traffic=if(Total traffic>=87,87,Total Traffic)
TSreqforAmendedTraffic Erlang table
HRRatio=((TSreq/average nbr avail TCH)-1)*100
NewHRRatio=if(HRratio>100,100,HRRatio)
omittingnegative=if(NewHRRatio<0,20,NewHRRatio) roundup
left=if(omitting<10,0,if(omitting<100,left(omitting),omitting))
right=if(omitting<10,omitting,if(omitting<100,right(omitting),omitting)) int
Rounded Right=if(right=100,100,if(right<=5,5,0)
Merged=if(rounded=100,100,if(rounded=5,left&rounded,(left+1)&rounded))
finalHR=Merged
Adaptive configuration of logical channel------------------
Increased STIME (40) will lower the SDCCH congestion
while decreased SLEVEL (2) will raise it.
TRH Load distribution:----------------------------------------------
RAHDC:CAPHYST=10,CAPLIM=20,STIME=0300,INTERVAL=24;
RAHPI:MP=0;
rahlc:AVELIM=25,NOTRHLIM=30,TRHLIM=10;
TRTSI:MP=0,TIME=0200,RPL=240,NDAYS=365,DATE=120710;
Flexible Abis -----------------------------------------------------------
1. TAB level
------------------
Full Rate AMR on 8 kbps
TAB=AXEPARS ,DAMRREDUCE=1.
Abis Triggered HR Allocation
TAB=AXEPARS, ATHAABIS=1.
Flexible Abis
TAB=AXEPARS,FLEXABIS=1
2.TG level :
----------------
ABISALLOC=FLEXIBLE
3.CHGR0 level
-----------------------
NUMREQEGPRBPC =6 if possible, check EGPRBPCLIMIT
4.Cell level
---------------
FPDCH = 2 or 1 or 0 it depends on data volume and CS congestion
SPDCH For save GSL utilusation
FLEXHIGHGPRS = 0
Abis ------
AbisCap = TS64 +TS16/4 + SigTS
SigTS = #TRX / ConFactor
TS16 = #TRX*8 #BCCH #SDCCH TS64
Flexible Priority Handling of Packet Data -------------------------------------
----
AXEPARS, PDCHPREEMPT=2
Cell, PDCHPREEMPT = 4
Queuing Feature:----------------------------------------------------------------
------
DESCRIPTION SOURCE NE LEVEL PARAMETER
Call Queuing BSCPROP BSC MSQUEUING
Abis Optimization:--------------------------------------------------------------
-------
Requires PGW Packet Gateway
Requires R06A
Requires dTRU based BTS
18 TRXs are handled with 1E1
SCGR
NUMDEV
DCP
SDAMRREDABISTHR
SDHRAABISTHR
SDFRMAABISTHR
ATHABIS
DAMRCRABIS
JBPTA
AMR ----------------------------------------------------------------------------
--------------
Besides the pre-defined codec sets (1, 2 and 5 for AMR FR and1 and 2 for AMR HR)
,
both AMR FR and AMR HR codec set 3and 4 are available.
These codec sets can be configured by the operator giving the possibility to fin
e tune AMR parameters
AMRFRSUPPORT 2
AMRHRSUPPORT 2
SET MODE THR HYST
FR3 1
FR3 3 12 2
FR3 4 21 3
FR3 7 21 3
FR4 1
FR4 3 12 2
FR4 6 17 3
FR4 8 25 3
HR3 1
HR3 3 23 3
HR3 4 28 4
HR3 5 32 4
HR4 1
HR4 3 23 3
HR4 5 31 4
MODE
THR
HYST
DTHAMR>DTHNAMR
50 20 or 40
70 60
90 80
RLINKUP 20
RLINKUPAFR 32
RLINKUPAHR 32
RLINKT 20
RLINKTAFR 32
RLINKTAHR 32

You might also like