Scribd
Upload
71 views6 pages

What Is RTWP?: Statistics Categories

This document discusses RTWP (Received Total Wideband Power), which is a measure of uplink interference in UMTS networks. Typical acceptable RTWP values range from -104.5 to -105.5 dBm, while higher values indicate increased interference that can degrade call performance. If RTWP is outside the typical range, the document recommends first checking configuration and hardware settings, then performing field testing and data collection over multiple days and cells to help locate potential external interference sources affecting the network. Maintaining RTWP close to -105 dBm can help improve call drop rates by reducing uplink interference.

Uploaded by

Opeyemi Dada
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
71 views6 pages

What Is RTWP?: Statistics Categories

This document discusses RTWP (Received Total Wideband Power), which is a measure of uplink interference in UMTS networks. Typical acceptable RTWP values range from -104.5 to -105.5 dBm, while higher values indicate increased interference that can degrade call performance. If RTWP is outside the typical range, the document recommends first checking configuration and hardware settings, then performing field testing and data collection over multiple days and cells to help locate potential external interference sources affecting the network. Maintaining RTWP close to -105 dBm can help improve call drop rates by reducing uplink interference.

Uploaded by

Opeyemi Dada
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

What is RTWP?

-
February 2011
+

S M T W T F S
30 31 1 2 3 4 5
6 7 8 9 10 11 12
13 14 15 16 17 18 19
20 21 22 23 24 25 26
27 28 1 2 3 4 5
6 7 8 9 10 11 12


Statistics

Entries (26)
Categories

Course (26)

LTE (1)

RF Components (1)
Related Posts

What is ISI (Inter Symbol Interference) in LTE?

What is Splitter and Combiner?

Analyzing Coverage with Propagation Delay - PD and Timing Advance - TA (GSM-WCDMA-LTE)

What is RRC and RAB?

What is Retransmission, ARQ and HARQ?

IP Packet switching in Telecom - Part 4

IP Packet switching in Telecom - Part 3

IP Packet switching in Telecom - Part 2

IP Packet switching in Telecom - Part 1

Goodbye IPv4... Hello IPv6!

What is Antenna Electrical and Mechanical Tilt (and How to use it)?

What is MIMO?

How to Run a RF Site Survey (Tips and Best Practices)

What is Ec/Io (and Eb/No)?

What is Cellular Field Test Mode?


Archives

February, 2014 (1)

October, 2013 (1)

June, 2013 (1)

May, 2013 (1)

June, 2012 (1)

March, 2012 (1)

February, 2012 (2)

January, 2012 (1)

November, 2011 (1)

October, 2011 (1)

September, 2011 (1)

June, 2011 (1)

April, 2011 (2)

March, 2011 (3)

February, 2011 (5)

January, 2011 (1)

December, 2010 (2)


Posted by leopedrini Tuesday, February 01, 2011 9:39:00 AM Categories: Course
Previous Post << >> Next Post
Rate this Content


20 Votes
If you work with UMTS,'ve probably heard someone talk about RTWP. Its definition can be
found in a dictionary of acronyms, such ashttp://acronyms.thefreedictionary.com/RTWP:
Received Total Wideband Power.
Represents a measure of UMTS technology: the total level of noise within the UMTS
frequency band of any cell.
RTWP is related to uplink interference, and its monitoring helps control the call drops -
mainly CS. It also has importance in the capacity management, as it provides information
for the Congestion Control regarding Uplink Interference.
In UMTS, the uplink interference may vary due to several factors, such as the number of
users in the cell, the Service, Connection Types and Conditions of Radio, etc..
As our goal is to always be as simple as possible, we will not delve in terms of formulas or
concepts involved. We will then know the typical values, and know what must be done in
case of problems.

Typical Values
Ok, we know that RTWP can help us in checking the uplink interference, then we need to
know its typical values.
In a network is not loaded, normal, acceptable RTWP Average value is generally around -
104.5 and -105.5 dBm.


Values around -95 dBm indicate that the cell has some uplink interferers.
If the value is around -85 dBm, the situation is ugly, with strong uplink interferers.
Usually we have High, Low and Medium measures of RTWP. However, the maximum and
minimum values are recommended only as auxiliary or reference, since they may have been
caused by a peak of access, or even been forced to have a momentary value due to some
algorithm i.e..
Thus, the value that helps us, and has the most accurate information is the same Mean
RTWP!
For cases in which cell has two carriers, the difference between them RTWP should not
exceed 6 dB.



Based on these typical values, most vendors have an alarm: RTWP "Very High. "

What to do in case of problems?
We have seen that RTWP can cause performance degradation, mainly CS Call Drops. Note:
Actually, it's not RTWP that causes performance degradation. What happens is that when its
value is 'bad', it's actually indicating the presence of interference - the latter being
responsible for degradation.
But what can we do when we find bad values?
If RTWP is not at acceptable levels, some actions should be taken.

The first thing to do is check if there is a configuration issue with the RNC or NodeB. This is the
most common case, especially in cases of new activations.

Once verified the parameter settings, the next step is the physical examination, especially jumpers
and cables, often partially reversed. It also should be checked if there is faulty transmitters, or any
other problem that could generate intermodulation between the NodeB and the antenna.

If the parameter settings and hardware are ok, the chance is very high that we have external
interference, such as a Interferer Repeater.
In cases where there may be external interference, we must begin to act after such a
prioritization based on how much this is affecting the cell KPI's across the network, if it
carry high traffic, major subscribers, etc..
Note: There are many forms of interference in the uplink, both internal and external. Only a
few are listed above. The deepening of all possibilities is beyond the goal of being simple to
teach the concepts, but this is a suggestion for whoever wants to deepen the study,
identification and elimination of interference.

In practice
to find - and eliminate - problems of interference is one of the biggest challenges in our
area. For being such a complex problem, we recommend that be collected enough data for
each investigation. Insufficient data collected can lead to erroneous conclusions, further
worsening the problem.
The uplink interference may appear only in specific periods. Thus, it is recommended that
data be collected from at least one week (7 days) for every 24 hours. Usually this amount of
data is sufficient. In the figure below, we see different days and times - colorful - a fictional
example where the interference occurred.


Data should be collected for the suspicious cell, but also for its adjacent cells, allowing it to
make a triangulation increasing the chances of locating the source of interference.
Another way to locate the source of interference is to do a test in field. An antenna guy
must gradually change the azimuth of the antenna, while another professional do RTWP
measurements. That is, through the information directing the antenna and the respective
values of RTWP, you can draw conclusions very good.
It is obvious that changing the online system may not be a good practice, and tests can be
made with a Yagi antenna and a Spectrum Analyzer.
Vendors offer several ways to measure RTWP, using the OSS, performance counters and
logs.

Conclusion
In this brief tutorial, we learn what is RTWP, and that the ideal typical value is about -104.5
dBm and -105.5 dBm.
As the RTWP is directly related to Uplink Interference - and we know that interference is the
main cause of performance degradation - have concluded that improving RTWP, ie making
is as close as possible to -105 dBm, improving the Call Drop Rate!
IMPORTANT : Seizing the opportunity, see what was stated at the start of this tutorial -
dictionary - by describing RTWP. Remember that this site has been the subject of a very
interesting tutorial in the TipsSection. If you have not visited this section of the portal yet , I
strongly recommend, because it has many issues that help in our growth in telecom and IT
area.

You might also like