EdgeOS User Guide

Operating System for Ubiquiti EdgeRouters
Release Version: 1.4

i
Table of Contents EdgeOS
User Guide
Ubiquiti Networks, Inc.
Table of Contents
Chapter 1: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Configuration Interface System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hardware Overview and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Typical Deployment Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Chapter 2: Using EdgeOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Ports and Status Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Common Interface Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Chapter 3: Dashboard Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 4: Routing Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
IPv6 Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
OSPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Chapter 5: Security Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Firewall Policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
NAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Firewall/NAT Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
VPN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Chapter 6: Services Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
PPPoE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Chapter 7: Users Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Local . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Chapter 8: Wizards Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Setup Wizards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Feature Wizards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
ii
Table of Contents EdgeOS
User Guide
Chapter 9: Toolbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Discover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Packet Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Log Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Appendix A: Command Line Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Access the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
CLI Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Appendix B: Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Ubiquiti Networks Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
1
Chapter 1: Overview EdgeOS
User Guide
Service Provider Deployment
This scenario uses six EdgeRouter devices:
1. OSPF Area 0 to OSPF Area 1
2. OSPF Area 0 to OSPF Area 2
3. OSPF Area 1
4. OSPF Area 1 to Internet
5. OSPF Area 2
6. OSPF Area 2 to Internet
eth0
eth1
eth2
eth0
eth1
eth2
eth0
eth1
eth2
eth0
eth1
eth2
eth0
eth1
eth2
eth0
eth1
eth2
eth0
eth1
eth2
Site-to-Site
Link
OSPF
Area 0
OSPF
Area 1
OSPF
Area 2
Internet
Internet
Site A
Site B
Here are the typical steps to follow:
1. Configure the appropriate settings on the System tab
(see System on page 4 for more information):
Host Name
Time Zone
Gateway
Name Server
Domain Name
NTP
2. Configure the interfaces on the Dashboard tab; see
Interfaces on page 9 for more information.
3. Configure OSPF settings on the Routing > OSPF tab; see
OSPF on page 17 for more information.
4. Configure DHCP server(s) on the Services tab; see
DHCP Server on page 30 for more information.
5. Configure NAT rules on the Security > NAT tab; see
NAT on page 24 for more information.
Chapter 1: Overview
Introduction
EdgeOS
is a powerful, sophisticated operating system

from Ubiquiti Networks
.
. It allows you to manage your
EdgeRouter and networks. This User Guide is designed for
use with version 1.3 or above of the EdgeOS Configuration
Interface and all of the EdgeRouter models, which this
User Guide will collectively refer to as EdgeRouter.
Additional information is available on our website at:
http://community.ubnt.com/edgemax
http://documentation.ubnt.com/edgemax
Product Name Model Number of Ports PoE
EdgeRouter Lite ERLite-3 3
EdgeRouter PoE ERPoe-5 5
8-Port EdgeRouter ER-8 8
EdgeRouter PRO ERPro-8 8*
* Two ports are either RJ45 or SFP.
Configuration
The intuitive EdgeOS Configuration Interface allows you
to conveniently manage your EdgeRouter using your web
browser. (See Using EdgeOS on page 3 for more
information.) If you need to configure advanced features
or prefer configuration by command line, you can use
the Command Line Interface (CLI). (See Command Line
Interface on page 45 for more information.)
Configuration Interface System
Requirements
Microsoft Windows 7, Windows 8, Linux, or Mac OS X
Web Browser: Google Chrome, Mozilla Firefox, or
Microsoft Internet Explorer 8 (or above)
Hardware Overview and Installation
The Quick Start Guide that accompanied your EdgeRouter
includes a hardware description and instructions for
hardware installation.
Typical Deployment Scenarios
While there are numerous scenarios that are possible, this
section highlights three typical deployments:
Small Office/Home Office (SOHO) Deployment
Service Provider Deployment
Corporate Deployment
SOHO Deployment
Click the Wizards tab and follow the on-screen
instructions. See Wizards Tab on page 37 for more
information.
2
Chapter 1: Overview EdgeOS
User Guide
6. Configure firewall rules on the Security > Firewall
Policies tab; see Firewall Policies on page 20 for
more information.
7. Configure additional settings as needed for your
network.
Corporate Deployment
This scenario uses a single EdgeRouter device. The three
independent interfaces connect to the following:
Internet
DMZ
LAN
eth0
eth1
eth2
Internet
DMZ
LAN
Firewall Policies
Here are the typical steps to follow:
1. Configure the appropriate settings on the System tab
(see System on page 4 for more information):
Host Name
Time Zone
Gateway
Name Server
Domain Name
NTP
2. Configure the interfaces on the Dashboard tab; see
Interfaces on page 9 for more information.
3. Configure DHCP server(s) on the Services tab; see
DHCP Server on page 30 for more information.
4. Configure NAT rules on the Security > NAT tab; see
NAT on page 24 for more information.
5. Configure firewall rules on the Security > Firewall
Policies tab; see Firewall Policies on page 20 for
more information.
6. Configure additional settings as needed for your
network.
3
Chapter 2: Using EdgeOS EdgeOS
User Guide
Chapter 2: Using EdgeOS
EdgeOS is a powerful, sophisticated operating system that
manages your EdgeRouter. It offers both a browser-based
interface (EdgeOS Configuration Interface) for easy
configuration and a Command Line Interface (CLI) for
advanced configuration.
To access the EdgeOS Configuration Interface:
1. Connect an Ethernet cable from the Ethernet port
of your computer to the port labeled eth0 on the
EdgeRouter.
eth0
eth1
eth2
2. Configure the Ethernet adapter on your computer
with a static IP address on the 192.168.1.x subnet (e.g.,
192.168.1.100).
Note: As an alternative, you can connect a serial
cable to the Console port of the EdgeRouter. See
Command Line Interface on page 45 for
more information.
3. Launch your web browser. Type https://192.168.1.1 in
the address field. Press enter (PC) or return (Mac).
4. The login screen will appear. Enter ubnt in the
Username and Password fields. Read the Ubiquiti
License Agreement, and check the box next to I agree
to the terms of this License Agreement to accept it. Click
Login.
The EdgeOS Configuration Interface will appear, allowing
you to customize your settings as needed.
Note: To enhance security, we recommend that you
change the default login using one of the following:
Set up a new user account on the Users > Local tab
(preferred option). For details, go to Add User
on page 35.
Change the default password of the ubnt login on
the Users > Local tab. For details, go to Configure
the User on page 36.
Ports and Status Information
The Ports image displays the active connections. An amber
port indicates 10/100 Mbps, and a green port indicates
1000 Mbps. The Status bar graphs display the following:
CPU The percentage of processing power used by the
EdgeRouter.
RAM The percentage of RAM used by the EdgeRouter.
Uptime The duration of the EdgeRouters activity.
Place your mouse over a port to view the following:
Enabled/Disabled The administrative status is displayed.
Link The connection status is displayed.
Speed The speed (in Mbps) and duplex mode are
displayed.
Navigation
The EdgeOS software consists of five primary tabs, and
some of these tabs have sub-tabs. This User Guide covers
each tab with a chapter. For details on a specific tab, refer
to the appropriate chapter.
Dashboard The Dashboard Tab on page 8
displays status information about services and
interfaces. You can also configure interfaces and Virtual
Local Area Networks (VLANs).
Routing The Routing Tab on page 14 configures
static routes and Open Shortest Path First (OSPF)
settings, including metrics, areas, and interfaces.
Security The Security Tab on page 20 configures
firewall policies, Network Address Translation (NAT)
rules, firewall/NAT groups, and PPTP VPN options.
Services The Services Tab on page 30 configures
DHCP servers, DNS forwarding, and the PPPoE server.
Users The Users Tab on page 35 configures user
accounts with administrator or operator access.
Wizards The Wizards Tab on page 37 offers
a variety of wizards: a setup wizard that configures
the EdgeRouter for a typical SOHO deployment and
feature wizards that configure port forwarding, TCP MSS
clamping, and UPnP.
4
User Guide
Depending on the tab you click, some of the screens
display information and options in multiple sections. You
can click the open/close tab to hide or display a section.
Open/Close Tab
Open/Close Tab
Common Interface Options
The common interface options are accessible from all tabs
on the EdgeOS interface:
Welcome
CLI
Toolbox
Alerts
System
Required fields are marked by a blue asterisk *. When the
information icon is displayed, you can click the icon for
more information about an option.
Welcome
At the top left of the screen, click Welcome to view the
Logout option:
Logout To manually log out of the EdgeRouter
Configuration Interface, click this option.
CLI
Advanced users can make configuration changes using
Linux commands. At the top right of the screen, click the
CLI button. See Command Line Interface on page
45 for more information.
Toolbox
At the top right of the screen, click the Toolbox
button. The following network administration and
monitoring tools are available:
Ping on page 42
Trace on page 43
Discover on page 43
Packet Capture on page 43
Log Monitor on page 44
Alerts
The number of new alerts is displayed in a red popup.
At the bottom of the screen, click the Alerts tab.
A table displays the following information about each
important event.
Message A description of the event is displayed.
Field The settings that are affected by the event are
displayed.
Actions The following options are available:
Remove Click this button to clear an alert.
Clear All Click this button to clear all alerts.
Click the top right corner of the Alerts tab to close it.
System
At the bottom of the screen, click the System tab to access
the device settings.
The device settings are organized into these sections:
Basic Settings on page 5
Management Settings on page 5
Configuration Management & Device Maintenance
on page 6
Restart & Shut Down Router on page 7
5
User Guide
Basic Settings
Host Name
System host name Enter a name for the EdgeRouter. The
host name identifies the EdgeRouter as a specific device.
For example, a .com URL typically uses this format:
<host_name>.domain_name.com
Time Zone
Use Coordinated Universal Time (UTC) UTC is the
international time standard used by Network Time
Protocol (NTP) servers. If your routers are located in
multiple time zones, then you may want to use UTC.
Time zone To set your network to a specific time zone,
select Time zone and configure the following:
Select continent/ocean Select your location.
Select country/region Select your location.
Select time zone Select your time zone.
Gateway
System gateway address Enter the IP address of your
gateway. This will set up your default route. If you want to
set up additional default routes, configure them as static
routes on the Routing tab. See Routing Tab on page
14 for more information.
Name Server
Domain Name System (DNS) translates domain names to
IP addresses; each DNS server on the Internet holds these
mappings in its respective DNS database.
System name server Enter the IP address of your DNS
server (example: 192.0.2.1 for IPv4 or 2001:db8::1 for IPv6).
Click Add New to add additional servers.
Domain Name
System domain name Enter the domain name of your
EdgeRouter. The domain name identifies the EdgeRouters
network on the Internet. For example, a .com URL typically
uses this format:
host_name.<domain_name>.com
NTP
NTP is a protocol for synchronizing the clocks of computer
systems over packet-switched, variable-latency data
networks. You can use it to set the system time on the
EdgeRouter. If the System Log option is enabled, then
the system time is reported next to every log entry that
registers a system event.
Automatically update system time using NTP By
default, the EdgeRouter obtains the system time from a
time server on the Internet.
Click Save to apply your changes.
Management Settings
SSH Server
Enable Enabled by default. This option allows SSH
(Secure Shell) access to the EdgeRouter for remote
configuration by command line. SSH uses encryption and
authentication, so it is a secure form of communication.
See Command Line Interface on page 45 for more
information.
Port Specify the TCP/IP port of the SSH server. The default
is 22.
6
User Guide
Telnet Server
Enable Disabled by default. This option allows Telnet
access to the EdgeRouter for remote configuration
by command line. Telnet is not a secure form of
communication, so we recommend SSH. See Command
Line Interface on page 45 for more information.
Port Specify the TCP/IP port of the Telnet server. The
default is 23.
System Log
Every logged message contains at least a system time and
host name. Usually a specific service name that generates
the system event is also specified within the message.
Messages from different services have different contexts
and different levels of detail. Usually error, warning, or
informational system service messages are reported;
however, more detailed debug level messages can also
be reported. The more detailed the system messages
reported, the greater the volume of log messages
generated.
Log to remote server This option allows the EdgeRouter
to send system log messages to a remote server. Enter
the remote host IP address and TCP/IP port that should
receive the system log (syslog) messages. 514 is the
default port for the commonly used, system message
logging utilities.
Note: Properly configure the remote host to receive
syslog protocol messages.
SNMP Agent
Simple Network Monitor Protocol (SNMP) is an
application layer protocol that facilitates the exchange
of management information between network
devices. Network administrators use SNMP to monitor
network-attached devices for issues that warrant
attention.
The EdgeRouter contains an SNMP agent, which does the
following:
Provides an interface for device monitoring using SNMP
Communicates with SNMP management applications
for network provisioning
Allows network administrators to monitor network
performance and troubleshoot network problems
For the purpose of equipment identification, configure the
SNMP agent with contact and location information:
Enable Disabled by default. This option activates the
SNMP agent.
SNMP community Specify the SNMP community string.
It is required to authenticate access to MIB (Management
Information Base) objects and functions as an embedded
password. The device supports a read-only community
string; authorized management stations have read access
to all the objects in the MIB except the community strings,
but do not have write access. The device supports SNMP
v1. The default is public.
Contact Specify the contact who should be notified in
case of emergency.
Location Specify the physical location of the EdgeRouter.
Configuration Management & Device
Maintenance
The controls in this section manage the device
configuration routines, firmware maintenance, and reset
to factory default settings.
Back Up Config
We recommend that you back up your current system
configuration before updating the firmware or uploading
a new configuration.
Download backup config file Click Download to
download the current system configuration file.
Note: We strongly recommend that you save the
configuration file in a secure location because it
includes confidential information. The user login
passwords are encrypted; however, other passwords
and keys (such as those used for VPN, BGP,
authentication, and RADIUS) are stored in plain text.
7
User Guide
Restore Config
Upload config file Click Upload a file to locate the
configuration file previously created by the Back Up Config
option. Select the file and click Choose. We recommend
that you back up your current system configuration before
uploading the new configuration.
Note for advanced users: You can also upload a
raw configuration file, /config/config.boot, using
thisoption.
Upgrade System Image
Download the firmware file from downloads.ubnt.com
and save it on your computer.
The firmware update is compatible with all configuration
settings. The system configuration is preserved while
the EdgeRouter is updated with a new firmware version.
However, we recommend that you back up your current
system configuration before updating the firmware.
Upload system image To update the EdgeRouter with
new firmware, click Upload a file and locate the new
firmware file. Then click Choose.
Please be patient, as the firmware update routine can take
three to seven minutes. You cannot access the EdgeRouter
until the firmware update routine is completed.
WARNING: Do not power off, do not reboot, and
do not disconnect the EdgeRouter from the power
supply during the firmware update process as these
actions will damage the EdgeRouter!
Reset Config to Default
This option resets the EdgeRouter to the default
configuration. This option will reboot the EdgeRouter, and
the default configuration will be restored. We recommend
that you back up your current system configuration before
resetting the EdgeRouter to its default configuration.
Reset to Default To reset the EdgeRouter to its default
configuration, click this option.
Restart & Shut Down Router
Restart Router
Restart To turn the EdgeRouter off and back on again,
click this option.
Shut Down Router
Shut Down To turn off the EdgeRouter, click this option.
WARNING: Click Shut Down to properly shut down
the EdgeRouter. An improper shutdown, such
as disconnecting the EdgeRouter from its power
supply, runs the risk of data corruption!
Click the top right corner of the System tab to close it.
8
Chapter 3: Dashboard Tab EdgeOS
User Guide
Chapter 3: Dashboard Tab
The Dashboard tab displays status information about
services and interfaces. You can also configure interfaces
and Virtual Local Area Networks (VLANs). Any setting
marked with a blue asterisk * is required.
Services
Status information is displayed. Each heading is a
convenient link to the appropriate tab.
Routes
The following route types are listed:
Connected
Static
RIP (Routing Information Protocol)
OSPF (Open Shortest Path First)
EBGP (Exterior Border Gateway Protocol)
IBGP (Interior Border Gateway Protocol)
The number of each route type and the total number
of routes are displayed. Click Routes to display the
Routing>Routes tab. Go to Routes on page 15 for
more information.
OSPF
The OSPF status, settings, and number of areas are
displayed. Click OSPF to display the Routing > OSPF tab.
Go to OSPF on page 17 for more information.
NAT
The NAT (Network Address Translation) status and number
of NAT rules are displayed. Click NAT to display the
Security > NAT tab. Go to NAT on page 24 for more
information.
Firewall
The firewall status and numbers of sets and rules are
displayed. Click Firewall to display the Security > Firewall
Policies tab. Go to Firewall Policies on page 20 for
more information.
9
User Guide
DHCP
The DHCP server status and numbers of active and
inactive servers are displayed. Click DHCP to display the
Services tab. Go to DHCP Server on page 30 for more
information.
Interfaces
Distribution
Click Hide Distribution to hide the Interfaces > Distribution
section. Click the remaining open/close tab to display the
Interfaces > Distribution section again.
Open/Close Tab
Select the physical or virtual interfaces you want to display
from the Interfaces column.
The TX Rate and RX Rate bar graphs display the
current data traffic, which is color-coded to match the
corresponding interface. The graph scale and throughput
dimension (Mbps, for example) change dynamically
depending on the mean throughput value. The statistics
are updated automatically.
Place your mouse over a bar to view the Current Rate and
Total Amount of traffic for the selected interfaces.
All/Ethernet/VLAN
Add VLAN To create a new VLAN, click Add VLAN.
The Create a New VLAN screen appears.
VLAN ID The VLAN ID is a unique value assigned to
each VLAN at a single device; every VLAN ID represents
a different VLAN. The VLAN ID range is 2 to 4094.
Interface Select the appropriate interface.
Description Enter keywords to describe this VLAN.
MTU Enter the MTU (Maximum Transmission Unit)
value, which is the maximum packet size (in bytes) that a
network interface can transmit. The default is 1500.
Address Select one of the following:
- No address settings The VLAN uses no address
settings. (In most cases, an address is needed.)
- Use DHCP The VLAN acquires network settings from
a DHCPv4 server.
- Use DHCP for IPv6 The VLAN acquires network
settings from a DHCPv6 server.
- Manually define IP address(es) Enter the
static IP address (example: 192.0.2.1/24 for IPv4
or 2001:db8::1/32 for IPv6). Click Add IP to enter
additional IP addresses.
Click Save to apply your changes, or click Cancel.
Search Allows you to search for specific text. Begin
typing; there is no need to press enter. The results are
filtered in real time as soon as you type two or more
characters.
10
User Guide
All/Ethernet/VLAN Click the appropriate tab to filter the
interfaces as needed.
All All interfaces are displayed by default.
Ethernet All of the Ethernet interfaces are displayed.
VLAN All VLANs are displayed.
interface. Click a column heading to sort by that heading.
Description The keywords you entered to describe the
interface are displayed.
Interface The name of the interface is displayed.
Note: A switch interface is created by default
(EdgeRouter PoE only); however, there are no
switched ports by default. To configure ports for the
switch interface, click Actions > Config and go to
Configure the Switch on page 12.
Type The type of interface is displayed.
PoE (Available for the EdgeRouter PoE only.) The status
(off) or voltage (24v/48v) of the PoE feature is displayed.
IP Addr The IP address of the interface is displayed.
MTU The MTU (Maximum Transmission Unit) value of the
interface is displayed. This is the maximum packet size (in
bytes) that the interface can transmit.
TX The transmit speed of the interface is displayed.
RX The receive speed of the interface is displayed.
Status The connection status of the interface is displayed.
Actions Click the Actions button to access the following
options:
Config To configure the interface, click Config.
If the interface is a physical port, go to the Configure the
Interface section.
If the interface is a VLAN, go to Configure the VLAN
on page 11.
If the interface is a switch (available for the EdgeRouter
PoE only), go to Configure the Switch on page 12.
PoE (Available for the EdgeRouter PoE only.) To
configure the PoE settings, click PoE. Go to Configure
the PoE Settings on page 12.
Disable Disable the interface while keeping its
configuration. (The switch interface cannot be disabled.)
Note: If you disable a port, its PoE functionality
remains. (This applies only to the EdgeRouter PoE.)
Delete (Available for VLANs only.) Delete the VLAN from
the EdgeRouter configuration.
Configure the Interface
After you click Config, the Interface Configuration screen
appears.
Make changes as needed.
Description Enter keywords to describe this interface.
Enable Check the box to enable the interface. All of
the interfaces are saved in the system configuration file;
however, only the enabled interfaces are active on the
device.
Note: If you disable a port, its PoE functionality
remains. (This applies only to the EdgeRouter PoE.)
- No address settings The interface uses no address
- Use DHCP The interface acquires network settings
from a DHCPv4 server. Click the Renew button to
acquire fresh network settings.
- Use DHCP for IPv6 The interface acquires network
11
User Guide
Speed/Duplex The default is Auto negotiation. The
EdgeRouter automatically negotiates transmission
parameters, such as speed and duplex, with its
counterpart. In this process, the networked devices
first share their capabilities and then choose the fastest
transmission mode they both support.
To manually specify the transmission link speed and
duplex mode, select one of the following options:
100/full, 100/half, 10/full, or 10/half.
Full-duplex mode allows communication in both
directions simultaneously. Half-duplex mode
allows communication in both directions, but not
simultaneously and only in one direction at a time.
Proxy ARP Enable the EdgeRouter to answer a source
hosts ARP (Address Resolution Protocol) requests for
the IP address of a destination host that is not located
on the source hosts network. ARP allows hosts on the
same network to discover each others IP address via a
layer 2 broadcast to all MAC addresses. If they are not on
the same network, the layer 2 broadcast will not reach
its destination; however, the EdgeRouter can serve as
the go-between if Proxy ARP is enabled.
Configure the VLAN
After you click Config, the Interface Configuration screen
appears.
VLAN ID The VLAN ID is displayed.
Parent The interface belonging to this VLAN is
displayed.
Description Enter keywords to describe this interface.
Enable Check the box to enable the VLAN. All of
the VLANs are saved in the system configuration file;
however, only the enabled VLANs are active on the
device.
- No address settings The interface uses no address
- Use DHCP The interface acquires network settings
from a DHCPv4 server. Click the Renew button to
acquire fresh network settings.
- Use DHCP for IPv6 The interface acquires network
12
User Guide
Configure the Switch
(Available for the EdgeRouter PoE only.) After you click
Config, the Interface Configuration screen appears.
Description Enter keywords to describe this switch.
- No address settings The switch uses no address
- Use DHCP The switch acquires network settings from
a DHCPv4 server. Click the Renew button to acquire
fresh network settings.
- Use DHCP for IPv6 The switch acquires network
Switch Ports Select the ports for the switch interface.
Configure the PoE Settings
Note: Before enabling PoE, check the specifications
of your airMAX, airVision, mFi, UniFi, legacy, or
third-party devices to ensure they support passive
PoE and require the available amount of voltage.
(Available for the EdgeRouter PoE only.) After you click PoE,
the PoE tab of the Interface Configuration screen appears.
PoE is disabled by default on all ports. Make changes as
needed.
PoE Select one of the following:
- Off To disable PoE, select Off.
Note: To disable PoE, you must use this setting. If
you disable a port, its PoE functionality remains.
- 24V To output 24V PoE to the connected device,
select 24V.
- 48V To output 48V PoE to the connected device,
select 48V.
Note: You must have a 48V power adapter
(not included) powering the EdgeRouter PoE;
otherwise, 48V PoE is not allowed.
PoE Watchdog
PoE Watchdog is only for PoE-enabled ports. It configures
the device to continuously ping a user-defined IP address
(it can be the Internet gateway, for example). If it is
unable to ping under the user-defined constraints, then
the device will automatically turn off PoE on the port,
and then turn it back on. This option creates a kind of
fail-proof mechanism.
PoE Watchdog is dedicated to continuous monitoring of
the specific connection to the remote host using the
Ping tool. The Ping tool works by sending ICMP echo
request packets to the target host and listening for ICMP
echo response replies. If the specified number of replies
is not received, the tool reboots the device.
13
User Guide
Enable Watchdog Enable the use of PoE Watchdog.
- IP Address To Ping Specify the IP address of the
target host to be monitored by PoE Watchdog.
- Ping Interval Specify the time interval (in seconds)
between the ICMP echo requests that are sent by PoE
Watchdog. The default value is 300 seconds.
- Startup Delay Specify the initial time delay (in
seconds) until the first ICMP echo requests are sent
by PoE Watchdog. The default value is 300 seconds.
The Startup Delay value should be at least 60 seconds
as the network interface and wireless connection
initialization takes a considerable amount of time if
the device is rebooted.
- Failure Count Specify the number of ICMP echo
response replies. If the specified number of ICMP
echo response packets is not received continuously,
PoE Watchdog will reboot the device. The default
value is3.
- Cut power for Specify the number of seconds this
port should pause PoE (if applicable).
WARNING: Cutting power during a firmware
upgrade can damage your device. Ensure that you
specify a safe Ping Interval.
14
Chapter 4: Routing Tab EdgeOS
User Guide
Chapter 4: Routing Tab
The Routing tab displays status information about a variety
of connected, static, RIP, and OSPF routes. You can also
configure static routes and OSPF options. Any setting
You have two sub-tabs:
Routes View route information and create static routes.
OSPF Configure OSPF options.
IPv6 Routing
IPv6 (Internet Protocol version 6) is gaining popularity
and is bound to grow as IP addressing demands increase.
The EdgeOS Configuration Interface supports IPv6 for the
following options:
System > Name Server configuration
(Refer to Name Server on page 5.)
Dashboard > VLAN configuration
(Refer to Add VLAN on page 9.)
Dashboard > Interface configuration
(Refer to Configure the Interface on page 10.)
For IPv6 addresses, the EdgeOS Configuration Interface
supports :: (double-colon) notation, which substitutes
:: for a contiguous sequence of 16-bit blocks set to zero.
Here is an example: 2001:db8::1
If written out, the IPv6 address becomes:
2001:db8:0000:0000:0000:0000:0000:0001
The EdgeOS Configuration Interface displays IPv6
addresses only in two locations:
System > Name Server section
Dashboard tab
The EdgeOS Configuration Interface will increase its
support of IPv6 in future releases. For other options, you
can use the CLI, which has comprehensive IPv6 support.
Note: Use the CLI to view IPv6 options configured
in the CLI but not supported by the EdgeOS
Configuration Interface.
15
User Guide
Routes
A route determines how traffic travels to its destination
network. If more than one route is suitable, the
EdgeRouter uses administrative distance as a metric to
compare all available routes, including directly connected
routes, manually configured static routes, dynamic routes,
and the default route. The EdgeRouter uses the route with
the lowest administrative distance.
All/Static/Connected/RIP/OSPF
Add Static Route To create a new static route, click Add
Static Route.
The Create Static Route screen appears.
Complete the following:
Select Route Type You have three options: Gateway,
Interface, or Black Hole.
- Gateway Define a route using the IP address and
subnet mask of the next hop gateway.
Destination network Enter the IP address and
subnet mask using slash notation:
<network_IP_address>/<subnet_mask_number>
(example: 192.0.2.0/24).
The first default route is configured on the System
tab; see System gateway address on page 5
for more information. To create multiple default
routes, set up static routes and enter 0.0.0.0/0.
Next hop address Enter the IP address.
Distance (1-255) Enter the administrative distance.
If there are identical routes from different sources
(such as static, RIP, or OSPF), the EdgeRouter
compares the routes and uses the route with the
lowest distance.
Enable Check the box to enable the route.
- Interface Define a route using a next hop interface.
(example: 192.0.2.0/24).
Next hop interface Select the appropriate
interface from the drop-down list.
(such as static, RIP, and OSPF), the EdgeRouter
lowest distance.
- Black Hole Define a route that drops unwanted
traffic.
(example: 192.0.2.0/24).
(such as static, RIP, and OSPF), the EdgeRouter
lowest distance.
characters.
16
User Guide
All/Static/Connected/RIP/OSPF Click the appropriate tab
to filter the routes as needed.
All All routes are displayed by default.
Static All static routes that you have configured are
displayed.
Connected All routes that are directly connected to the
EdgeRouter are displayed.
RIP All RIP (Routing Information Protocol) routes are
displayed. RIP is an interior, distance vector routing
protocol that uses hop count as a metric to determine
the best route.
OSPF All OSPF (Open Shortest Path First) routes are
displayed. OSPF is an interior, link-state routing protocol
that uses cost as a metric to determine the best route.
The bandwidth of an interface determines the cost the
higher the bandwidth, the lower the cost.
route. Click a column heading to sort by that heading.
Selected The status of the route, whether it has been
selected for the routing table, is displayed.
Destination The destination IP address is displayed.
Next Hop The IP address of the next-hop interface is
displayed.
Route Type The type of route is displayed.
In FIB The forwarding status of the route, whether it is in
the FIB (Forwarding Information Base), is displayed.
options:
Config To configure the route, click Config. Go to the
Configure the Static Route section below.
Delete Delete the route; its configuration will be
removed.
Disable Disable the route while keeping its
configuration. (This option is not available for black hole
routes.)
Configure the Static Route
After you click Config, the Static Route Configuration screen
appears.
Follow the instructions for your route type:
Gateway
Route type The gateway route uses the IP address and
subnet mask of the next hop gateway.
Destination network The IP address and subnet mask
are displayed in slash notation.
Next hop address The IP address of the next hop
gateway is displayed.
Distance (1-255) Enter the administrative distance. If
there are identical routes from different sources (such
as static, RIP, and OSPF), the EdgeRouter compares the
routes and uses the route with the lowest distance.
Interface
Route type The interface route uses the next hop
interface.
Next hop interface The name of the next hop interface
is displayed.
17
User Guide
Black Hole
Route type The black hole route drops unwanted traffic.
OSPF
Using Link State Advertisements, routers communicate
with each other when there is a router or link status
change. Each router maintains the information in a
database, which is used to create and update a network
map from the routers point of view. Each router then uses
the map to build and update a routing table.
Router
Router ID Enter the IP address that identifies a specific
router in an OSPF network. In OSPF, the highest Router ID
determines which router is the Designated Router (DR),
which distributes updates to the other OSPF routers.
Click Save to apply your changes, or click Delete OSPF
to remove the Router, Redistribution, and Area settings
(Interfaces settings are retained).
Redistribution
A single router can use multiple routing protocols, such
as OSPF and RIP, which use incompatible metrics. It
must reconcile information from multiple protocols to
determine which route to use for a specific destination
network. You can change the metrics of the distributed
protocol to create protocol compatibility.
Redistribute connected If enabled, the EdgeRouter
connects an OSPF area to a network using a different
routing protocol and redistributes the other protocols
directly connected routes into the OSPF area. These routes
become external OSPF routes.
- Metric If there are multiple routes to the same
destination, OSPF uses the metric to select a route
for the routing table. Assign a cost value to the
redistributed connected routes. The EdgeRouter can
then use this metric to compare these routes to other
OSPF routes.
Redistribute static If enabled, the EdgeRouter connects
an OSPF area to a network using a different routing
protocol and redistributes the other protocols static
routes into the OSPF area. These routes become external
OSPF routes.
- Metric If there are multiple routes to the same
destination, OSPF uses the metric to select a route
for the routing table. Assign a cost value to the
redistributed static routes. The EdgeRouter can then
use this metric to compare these routes to other OSPF
routes.
Announce default route If enabled, the EdgeRouter
communicates the default route to the other routers of
the OSPF network, eliminating the need to configure
the default route on the other routers. The default route
connects the OSPF network to an outside network.
18
User Guide
Areas
To enhance scalability, an OSPF network is comprised of
smaller sections called areas. At the minimum, there is the
backbone area, called Area 0.
Add Area To create a new area, click Add Area.
The Create OSPF Area screen appears.
Area ID This is the number that identifies an area. It can
be an integer or use a format similar to an IPv4 address.
Area Type This defines the routes that are acceptable
inside the area. Select the appropriate option:
- Normal/sec The default type accepts all routes.
- NSSA A NSSA (Not So Stubby Area) network is a
variation of a stub network. It can import external
routes from type 7 Link State Advertisements, which
are NSSA-specific.
- Stub The network has no external routes. Typically, it
has a default route for outbound traffic.
Auth Type Authentication helps secure communication
between routers. Select the appropriate option:
- Off No authentication is used.
- MD5/sec Each router uses a key (password) and key
ID. This is the most secure option because the key is
never transmitted.
- Plain text Each router uses a key. This provides
minimal security because the key is transmitted in
plain text format.
Network Enter the IP address and subnet mask using
slash notation:
(example: 192.0.2.0/24).
Click Add New to enter more network addresses.
OSPF Area. Click a column heading to sort by that
heading.
Area ID The identification number of the area is
displayed.
Area Type The type of area is displayed.
Auth Type The authentication type of the area is
displayed.
Network The network address of the area is displayed.
options:
Config To configure the OSPF Area, click Config. Go to
the Configure the OSPF Area section.
Delete Delete the OSPF Area.
Configure the OSPF Area
After you click Config, the OSPF Area Configuration screen
appears.
Area ID This is the number that identifies an area. It can
be an integer or use a format similar to an IPv4 address.
Area Type This defines the routes that are acceptable
inside the area. Select the appropriate option:
- Normal/sec The default type accepts all routes.
- NSSA A NSSA (Not So Stubby Area) network is a
variation of a stub network. It can import external
routes from type 7 Link State Advertisements, which
are NSSA-specific.
- Stub The network has no external routes. Typically, it
has a default route for outbound traffic.
never transmitted.
plain text format.
19
User Guide
Network Enter the IP address and subnet mask using
slash notation:
(example: 192.0.2.0/24).
Interfaces
You can configure interfaces with specific OSPF options.
Add OSPF Interface To create a new interface, click Add
OSPF Interface.
The OSPF Interface Configuration screen appears.
Interface Select the appropriate interface from the
drop-down list.
Auth Type OSPF authentication helps secure
communication between routers. Select the appropriate
option:
never transmitted.
plain text format.
Auth Key Enter the key used for authentication.
Cost By default, the cost of an interface is based on its
bandwidth; however, you can manually assign a cost to
the interface.
OSPF Interface. Click a column heading to sort by that
heading.
Cost The cost of the interface is displayed. OSPF uses cost
as a metric to determine the best route.
options:
Config To configure the OSPF Interface, click Config.
Go to the Configure the OSPF Interface section.
Delete Delete the OSPF Interface.
Configure the OSPF Interface
After you click Config, the OSPF Interface Configuration
screen appears.
never transmitted.
plain text format.
Auth Key Enter the key used for authentication.
Cost By default, the cost of an interface is based on its
bandwidth; however, you can manually assign a cost to
the interface.
20
Chapter 5: Security Tab EdgeOS
User Guide
Chapter 5: Security Tab
The Security tab displays status information about firewall
policies, firewall groups, (Network Address Translation)
rules, and PPTP VPN options. You can also configure these
policies, groups, rules, and options. Any setting marked
with a blue asterisk * is required.
You have four sub-tabs:
Firewall Policies Each firewall policy is a set of rules
applied in the order you specify.
NAT View and create NAT rules.
Firewall/NAT Groups Create groups defined by IP
address, network address, or port number.
VPN Configure the EdgeRouter as a PPTP VPN server.
Firewall Policies
A firewall policy is a set of rules with a default action.
Firewall policies are applied before SNAT (Source Network
Address Translation) and after DNAT (Destination Network
Address Translation).
To create a firewall policy:
1. Click the Firewall/NAT Groups tab, and create the
applicable firewall groups. See Firewall/NAT Groups
on page 28 for more information.
2. Click the Firewall Policies tab, and then click Add
Policy. Configure the basic parameters. See the
Add Policy description in the next column for more
information.
3. Configure the details of the firewall policy. See
Configure the Firewall Policy on page 21 for
more information.
All/Drop/Reject/Accept
Add Policy To create a new policy, click Add Policy.
The Create New Ruleset screen appears.
Name Enter a name for this policy.
Description Enter keywords to describe this policy.
Default action All policies have a default action if the
packets do not match any rule. Select the appropriate
default action:
- Drop Packets are blocked with no message.
- Reject Packets are blocked, and an ICMP (Internet
Control Message Protocol) message is sent saying the
destination is unreachable.
- Accept Packets are allowed through the firewall.
21
User Guide
Default Log Check this box to log packets that trigger
the default action.
characters.
All/Drop/Reject/Accept Click the appropriate tab to filter
the policies by default action.
All All policies are displayed by default.
Drop All of the drop policies are displayed.
Reject All of the reject policies are displayed.
Accept All of the accept policies are displayed.
policy. Click a column heading to sort by that heading.
Name The name of the policy is displayed.
Interfaces The specified interface and direction of traffic
flow are displayed.
Number of Rules The number of rules in the policy is
displayed.
Default Action The action that the policy will execute if
the packets do not match any rule is displayed.
options:
Edit Rules To configure the rules, click Edit Rules. Go to
the Rules section in the next column.
Configuration To configure the policy, click
Configuration. Go to Configuration on page 24.
Interfaces To select interfaces and direction of traffic
flow for your policy, click Interfaces. Go to Interfaces
on page 24.
Stats To view statistics on firewall usage, click Stats. Go
to Stats on page 24.
Copy Policy To create a duplicate, click Copy Policy.
The Copy Firewall Ruleset screen appears.
- Name Enter a new name for this policy.
Click Copy to confirm, or click Cancel.
Delete Policy Remove the policy.
Configure the Firewall Policy
The Ruleset Configuration for _ screen appears.
You have four tabs available:
Rules (see below)
Configuration on page 24
Interfaces on page 24
Stats on page 24
Add New Rule To create a new rule, click Add New Rule.
Go to Add or Configure a Rule on page 22.
Save Rule Order To change the rule order, click and drag
a rule up or down the sequence, and then release the rule.
When you are finished, click Save Rule Order.
Rules
A rule tells the EdgeRouter what action to take with a
specific packet. Define the following:
Criteria for matching packets
Action to take with matching packets
Rules are organized into a set and applied in the specified
Rule Order. If the packets match a rules criteria, then its
action is triggered. If not, then the next rule is applied.
A table displays the following information about each rule.
Click a column heading to sort by that heading.
Order The rules are applied in the order specified. The
number of the rule in this order is displayed.
Description The keywords you entered to describe this
rule are displayed.
Source The source specified by this rule is displayed.
Destination The destination specified by this rule is
displayed.
Protocol The protocol that matches the rule is displayed.
Action The action specified by this rule is displayed.
options:
Basic To configure the basic options of a rule, click
Basic. Go to Basic on page 22.
Advanced To configure the advanced options of a rule,
click Advanced. Go to Advanced on page 22.
Source To configure the source options of a rule, click
Source. Go to Source on page 23.
Destination To configure the destination options of a
rule, click Destination. Go to Destination on page
23.
Time To configure the time options of a rule, click Time.
Go to Time on page 23.
22
User Guide
Copy Rule To create a duplicate, click Copy Rule. The
duplicate rule appears at the bottom of the list.
Delete Rule Remove the rule.
Add or Configure a Rule
The Rule Configuration for _ screen appears. You have five
tabs available:
Basic (see below)
Advanced (see the next column)
Source on page 23
Destination on page 23
Time on page 23
Basic
Description Enter keywords to describe this rule.
Enable Check the box to enable this rule.
Action Select the action for packets that match this
rules criteria.
- Drop Packets are blocked with no message.
- Reject Packets are blocked, and an ICMP (Internet
- Accept Packets are allowed.
Protocol
- All protocols Match packets of all protocols.
- TCP Match TCP packets.
- UDP Match UDP packets.
- Both TCP and UDP Match TCP and UDP packets.
- Choose a protocol by name Select the protocol from
the drop-down list. Match packets of this protocol.
Match all protocols except for this Match packets
of all protocols except for the selected protocol.
- Enter a protocol number Enter the port number of
the protocol. Match packets of this protocol.
Logging Check this box to log instances when the rule
is matched.
Advanced
State This describes the connection state of a packet.
- Established Match packets that are part of a two-way
connection.
- Invalid Match packets that cannot be identified.
- New Match packets creating a new connection.
- Related Match packets related to established
connections.
Recent Time Enter the number of seconds to monitor
for attempts to connect from the same source.
Recent Count Enter the number of times the same
source is detected within the Recent Time duration.
This helps thwart attacks using continual attempts to
connect.
IPsec IPsec (Internet Protocol security) helps secure
packet routing.
- Dont match on IPsec packets Do not match any
IPsec packets.
- Match inbound IPsec packets Match IPsec packets
that are entering the EdgeRouter.
- Match inbound non-IPsec packets Match non-IPsec
packets that are entering the EdgeRouter.
23
User Guide
P2P Match P2P (Peer-to-Peer) applications.
- None Do not match P2P connections.
- All Match all P2P connections.
- Choose P2P app(s) by name Match packets of the
selected P2P application(s). Check the box of any P2P
application on this list to select it.
Source
Address Enter the IP address of the source.
Port Enter the port number or range of the source.
MAC Address Enter the MAC address of the source.
Firewall groups are created on the Firewall/NAT Groups
tab; see Firewall/NAT Groups on page 28 for
more information. Select the appropriate group(s);
you can specify up to two groups maximum in these
combinations:
An address group and port group
A network group and port group
The packets must match both groups to apply the rule.
Address Group or Interface Addr. Select the
appropriate address group or interface address. If you
select Other as the interface address, then enter the
interface name in the field provided. The firewall rule
will match the IP address of the selected interface.
Network Group Select the appropriate network group.
Port Group Select the appropriate port group.
Destination
Address Enter the IP address of the destination.
Port Enter the port number of the destination.
Firewall groups are created on the Firewall/NAT Groups
combinations:
Address Group or Interface Addr. Select the
interface name in the field provided. The firewall rule
will match the IP address of the selected interface.
Network Group Select the appropriate network group.
Port Group Select the appropriate port group.
Time
Month Days Enter the days of the month when the rule
should be applied. Enter numbers in the range 1 to 31.
If you enter more than one day, use commas to separate
the numbers (example: 3, 4, 5).
- Match all month days except for these Match all
days of the month except for the selected days.
24
User Guide
Week Days Enter the days of the week when the rule
should be applied. Enter Sun, Mon, Tue, Wed, Thu, Fri,
or Sat. If you enter more than one day, use commas to
separate the days (example: Mon, Tue, Wed).
- Match all week days except for these Match all days
of the week except for the selected days.
Start Date Enter the date the rule should start being
applied. Use the YYYY-MM-DD (year-month-day) format.
Start Time Enter the time the rule should start
being applied. Use the 24-hour format, HH:MM:SS
(hours:minutes:seconds).
Stop Date Enter the date the rule should stop being
applied. Use the YYYY-MM-DD (year-month-day) format.
Stop Time Enter the time the rule should stop
being applied. Use the 24-hour format, HH:MM:SS
(hours:minutes:seconds).
Interpret dates and times as UTC Check the box if
your network uses UTC.
Configuration
Name The name of this policy is displayed.
Description Enter keywords to describe this policy.
Default action All policies have a default action if the
packets do not match any rule. Select the appropriate
default action:
Drop Packets are blocked with no message.
Reject Packets are blocked, and an ICMP (Internet
Accept Packets are allowed.
Default Log Check this box to log packets that trigger the
default action.
Click Save Ruleset to apply your changes.
Interfaces
Interface Select the appropriate interface from the
drop-down list.
Direction Select the direction of the traffic flow.
- in Match inbound packets.
- out Match outbound packets.
- local Match local packets.
Add Interface Click Add Interface to enter more
interfaces.
Click Save Ruleset to apply your changes.
Stats
A table displays the following statistics about each rule.
Rule The rules are applied in the order specified. The
Packets The number of packets that triggered this rule is
displayed.
Bytes The number of bytes that triggered this rule is
displayed.
Action The action specified by this rule is displayed.
rule are displayed.
NAT
NAT changes the addressing of packets. A NAT rule tells
the EdgeRouter what action to take with a specific packet.
Define the following:
Criteria for matching packets
Action to take with matching packets
Rules are organized into a set and applied in the specified
Rule Order. If the packets match a rules criteria, then its
action is performed. If not, then the next rule is applied.
25
User Guide
Source NAT Rules
Source NAT Rules change the source address of packets;
a typical scenario is that a private source needs to
communicate with a public destination. A Source NAT
Rule goes from the private network to the public network
and is applied after routing, just before packets leave the
EdgeRouter.
Add Source NAT Rule To create a new rule, click Add
Source NAT Rule. Go to Add or Configure a Source NAT
Rule on page 25.
characters.
rule are displayed.
Source Addr. The source IP address is displayed.
Source Port The source port number is displayed.
Dest. Addr. The destination IP address is displayed.
Dest. Port The destination port number is displayed.
Translation A description of the translation (such as
masquerade to eth_) is displayed.
Count The number of translations is displayed.
options:
Config To configure the rule, click Config. Go to the
Add or Configure a Source NAT Rule section below.
Copy To create a duplicate, click Copy. The duplicate
rule appears at the bottom of the list.
Delete Remove the rule.
Add or Configure a Source NAT Rule
After you click Config, the Source NAT Rule Configuration
screen appears.
Outbound Interface Select the interface through
which the outgoing packets exit the EdgeRouter. This is
required only for Source NAT Rules that use Masquerade.
Translation Select one of the following:
- Use Masquerade Masquerade is a type of Source
NAT. If enabled, the source IP address of the packets
becomes the public IP address of the outbound
interface.
- Specify address and/or port If enabled, the source
IP address of the packets becomes the specified IP
address and port.
Address Enter the IP address that will replace the
source IP address of the outgoing packet. You can
also enter a range of IP addresses; one of them will
be used.
Port Enter the port number that will replace the
source port number of the outgoing packet. You
can also enter a range of port numbers; one of them
will be used.
Exclude from NAT Check the box to exclude packets
that match this rule from NAT.
26
User Guide
Enable Logging Check this box to log instances when
the rule is matched.
Protocol Select one of the following:
Src Address Enter the IP address or network address of
the source. You can also enter a range of IP addresses;
one of them will be used.
Note: If you enter a network address, enter the IP
address and subnet mask using slash notation:
(example: 192.0.2.0/24).
Src Port Enter the port name or number of the source.
You can also enter a range of port numbers; one of them
will be used.
NAT groups are created on the Firewall/NAT Groups
combinations:
Src Address Group or Interface Addr. Select the
interface name in the field provided. The NAT rule will
match the IP address of the selected interface.
Src Network Group Select the appropriate network
group.
Src Port Group Select the appropriate port group.
Dest. Address Enter the IP address or network address
of the destination. You can also enter a range of IP
addresses; one of them will be used.
(example: 192.0.2.0/24).
Dest. Port Enter the port name or number of the
destination. You can also enter a range of port numbers;
Dest Address Group or Interface Addr. Select the
Dest Network Group Select the appropriate network
group.
Dest Port Group Select the appropriate port group.
Destination NAT Rules
Destination NAT Rules change the destination address of
packets; a typical scenario is that a public source needs
to communicate with a private destination. A Destination
NAT Rule goes from the public network to the private
network and is applied before routing.
Add Destination NAT Rule To create a new rule, click
Add Destination NAT Rule. Go to the Add or Configure a
Destination NAT Rule section.
characters.
27
User Guide
rule are displayed.
Source Addr. The source IP address is displayed.
Source Port The source port number is displayed.
Dest. Addr. The destination IP address is displayed.
Dest. Port The destination port number is displayed.
Translation A description of the translation (such as to
<IP_address>) is displayed.
Count The number of translations is displayed.
options:
Config To configure the rule, click Config. Go to the
Add or Configure a Destination NAT Rule section below.
Copy To create a duplicate, click Copy. The duplicate
rule appears at the bottom of the list.
Delete Remove the rule.
Add or Configure a Destination NAT Rule
After you click Config, the Destination NAT Rule
Configuration screen appears.
Inbound Interface Select the interface through which
the incoming packets enter the EdgeRouter.
Translations Complete the following:
- Address Enter the IP address that will replace the
destination IP address of the incoming packet.
- Port Enter the port number that will replace the
destination port number of the incoming packet.
Exclude from NAT Check the box to exclude packets
that match this rule from NAT.
Enable Logging Check this box to log instances when
the rule is matched.
Protocol
Src Address Enter the IP address or network address of
the source. You can also enter a range of IP addresses;
(example: 192.0.2.0/24).
Src Port Enter the port name or number of the source.
You can also enter a range of port numbers; one of them
will be used.
NAT groups are created on the Firewall/NAT Groups
combinations:
28
User Guide
Src Address Group or Interface Addr. Select the
Src Network Group Select the appropriate network
group.
Src Port Group Select the appropriate port group.
Dest. Address Enter the IP address or network address
of the destination. You can also enter a range of IP
addresses; one of them will be used.
(example: 192.0.2.0/24).
Dest. Port Enter the port name or number of the
destination. You can also enter a range of port numbers;
Dest Address Group or Interface Addr. Select the
Dest Network Group Select the appropriate network
group.
Dest Port Group Select the appropriate port group.
Firewall/NAT Groups
Create groups organized by IP address, network address,
or port number.
All/Address/Network/Port
Add Group To create a new group, click Add Group.
The Create New Group screen appears.
Name Enter a name for this group.
Description Enter keywords to describe this group.
Group Type Select the appropriate option:
- Address Group Define a group by IP address.
- Network Group Define a group by network address.
- Port Group Define a group by port numbers.
characters.
All/Address/Network/Port Click the appropriate tab to
filter the groups as needed.
All All groups are displayed by default.
Address All of the address groups are displayed.
Network All of the network groups are displayed.
Port All of the port groups are displayed.
group. Click a column heading to sort by that heading.
Name The name of the group is displayed.
Description The keywords you entered to describe the
group are displayed.
Type The type of group is displayed.
Number of group members The number of members is
displayed.
options:
Config To configure the group, click Config. Go to the
Configure the Firewall/NAT Group section below.
Delete Remove the group.
29
User Guide
Configure the Firewall/NAT Group
After you click Config, the Edit Firewall Group screen
appears. Follow the instructions for your group type:
Address Group Make changes as needed.
- Name The name of this group is displayed.
- Description Enter keywords to describe this group.
- Address Enter the IP address or range of addresses
(examples: 192.0.2.1 or 192.0.2.1-15). Click Add New to
enter more IP addresses.
Network Group Make changes as needed.
- Network Enter the IP address and subnet mask using
slash notation:
(example: 192.0.2.0/24).
Port Group Make changes as needed.
- Port Enter the port name, number, or range. Click
Add New to enter more ports.
VPN
A common type of VPN uses PPTP (Point-to-Point
Tunneling Protocol). The EdgeRouter can function as a
PPTP VPN server so a remote VPN client can access the
LAN using a PPTP VPN tunnel over the Internet.
PPTP Server
Client IP pool range start The client IP pool is the pool
of IP addresses that remote VPN clients will use. Enter the
starting IP address of the range (this address must in a /24
subnet).
Client IP pool range stop Enter the last IP address of the
range.
Server outside address Enter the IP address that VPN
clients will connect to; this is the outside or external
address of the PPTP server.
RADIUS server IP address The RADIUS (Remote Access
Dial-In User Service) server provides authentication to
help secure VPN tunnels. Enter the IP address of the
RADIUS server.
RADIUS server key Enter the key shared with the RADIUS
server.
network interface can transmit. The default is 1492 for the
PTTP VPN connection.
DNS 1 Enter the IP address of the primary remote access
DNS server that your VPN client will use.
DNS 2 Enter the IP address of the secondary remote
access DNS server.
30
Chapter 6: Services Tab EdgeOS
User Guide
Chapter 6: Services Tab
The Services tab displays status information about DHCP
servers, DNS forwarding, and the PPPoE server. Any setting
You have three sub-tabs:
DHCP Server Configure DHCP servers to implement
different subnets on the independent interfaces.
DNS Configure DNS forwarding so the EdgeRouter
receives all LAN DNS requests and forwards them to the
service providers DNS server.
PPPoE Server Configure the PPPoE server so a remote
PPPoE client can establish a tunnel to the EdgeRouter for
network access.
DHCP Server
A DHCP server assigns IP addresses to DHCP clients. You
can configure multiple DHCP servers to assign IP ranges in
different subnets on the different interfaces.
Add DHCP Server To create a new DHCP server, click Add
DHCP Server.
The Create DHCP Server screen appears.
DHCP Name Enter a name for this DHCP server.
Subnet Enter the IP address and subnet mask using
slash notation:
(example: 192.0.2.0/24).
Range Start Enter the starting IP address of the range.
Range Stop Enter the last IP address of the range.
Router Enter the default route of the DHCP clients. The
DHCP clients route all packets to this IP address, which is
the EdgeRouters own IP address in most cases.
DNS 1 Enter the IP address of the primary DNS server.
Your ISP may provide this information, or you can use
Googles DNS server at 8.8.8.8.
DNS 2 Enter the IP address of the secondary DNS server.
31
User Guide
UniFi Controller Enter the IP address of the UniFi
Controller. The DHCP server will return the UniFi
Controllers IP address to its DHCP clients, so if a client
is a UniFi AP, it will know how to contact the UniFi
Controller.
Enable Check the box to enable this DHCP server.
characters.
DHCP server. Click a column heading to sort by that
heading.
Name The name of the DHCP server is displayed.
Subnet The IP address and subnet mask of the DHCP
server are displayed.
Pool size The total number of IP addresses is displayed.
Leased The number of leased IP addresses is displayed.
Available The number of available IP addresses is
displayed.
options:
View Leases To view the current DHCP leases, click
View Leases. Go to the Configure the DHCP Server >
Leases section.
Configure Static Map To map static IP addresses to
MAC addresses, click Configure Static Map. Go to
Static MAC/IP Mapping on page 32.
View Details To configure the DHCP server, click View
Details. Go to Details on page 33.
Delete Delete the DHCP server; its configuration will be
removed.
Disable Disable the DHCP server while keeping its
configuration.
Configure the DHCP Server
The DHCP Server - screen appears. You have three tabs
available.
Leases
The top section displays the following status information:
Pool Size The total number of IP addresses is displayed.
The DHCP server assigns IP address from the pool (or
group) of IP addresses.
Leased The number of used IP addresses is displayed.
displayed.
server are displayed in slash notation.
Range Start The starting IP address of the range is
displayed.
Range End The last IP address of the range is displayed.
Router The default route of the DHCP clients is
displayed. The DHCP clients route all packets to this IP
address, which is the EdgeRouters own IP address in
most cases.
DNS The IP address of the DNS server is displayed.
Status The Enabled/Disabled status of the DHCP server
is displayed.
characters.
32
User Guide
DHCP client. Click a column heading to sort by that
heading.
IP Address The IP address assigned to the DHCP client
is displayed.
Hardware Address The MAC address of the DHCP
client is displayed.
Lease Expiration The date and time when the DHCP
lease will expire is displayed.
Pool The name of the DHCP server is displayed.
Hostname The name used to identify the DHCP client is
displayed.
At the bottom of the screen, you can click Delete to
delete the DHCP server and its configuration.
Static MAC/IP Mapping
displayed.
displayed.
most cases.
is displayed.
Create New Mapping To map a static IP address to a
specific MAC address, click Create New Mapping.
The Create Static MAC/IP Mapping appears.
- ID Enter a name for this mapping.
- MAC Address Enter the MAC address of the DHCP
client.
- IP Address Enter the IP address that should be
assigned.
characters.
static MAC/IP mapping. Click a column heading to sort by
that heading.
Name The name of the mapping is displayed.
MAC Address The MAC address of the DHCP client is
displayed.
IP Address The IP address assigned to the
corresponding MAC address is displayed.
Actions Click the Actions button to access the
following options:
- Config To configure the mapping, click Config. Go to
Configure Static MAC/IP Mapping on page 33.
- Delete Remove the selected mapping.
33
User Guide
Configure Static MAC/IP Mapping
The Static MAC/IP Mapping screen appears.
- ID The name of this mapping is displayed.
- MAC Address Enter the MAC address of the DHCP
client.
- IP Address Enter the IP address that should be
assigned.
Details
displayed.
displayed.
most cases.
is displayed.
The rest of the Details tab displays the following:
DHCP Name The name of the DHCP server is displayed.
Make changes as needed to the following options:
Range Start Enter the starting IP address of the range.
Range Stop Enter the last IP address of the range.
Router Enter the default route of the DHCP clients. The
DHCP clients route all packets to this IP address, which is
the EdgeRouters own IP address in most cases.
UniFi Controller Enter the IP address of the UniFi
Controller. The DHCP server will return the UniFi
Controllers IP address to its DHCP clients, so if a client
is a UniFi AP, it will know how to contact the UniFi
Controller.
DNS 1 Enter the IP address of the primary DNS server.
Your ISP may provide this information, or you can use
Googles DNS server at 8.8.8.8.
DNS 2 Enter the IP address of the secondary DNS server.
Domain Enter the domain name for DHCP clients.
Lease Time Enter the period of time (in seconds) that a
DHCP lease should last.
Enable Check the box to enable this DHCP server.
34
User Guide
DNS
The EdgeRouter receives all LAN DNS requests and
forwards them to the service providers DNS server. The
EdgeRouter receives responses from the DNS server and
forwards them to the LAN clients.
DNS Forwarding
Cache Size Completed DNS requests are cached so
response time is faster for cached entries, and there is less
traffic traveling to the DNS server. Enter the maximum
number of DNS queries to cache.
Interface Select the appropriate interface that the
EdgeRouter will listen to so it can forward DNS requests.
Add Listen Interface You can select multiple interfaces.
To add another interface for DNS forwarding, click Add
Listen Interface. From the new Interface drop-down
menu, select the appropriate interface.
PPPoE
The EdgeRouter can function as a PPPoE (Point-to-Point
Protocol over Ethernet) server so a remote PPPoE client
can establish a tunnel to the EdgeRouter for network
access.
PPPoE Server
Client IP pool range start The client IP pool is the pool of
IP addresses that remote PPPoE clients will use. Enter the
starting IP address of the range (this address must in a /24
subnet).
Client IP pool range stop Enter the last IP address of the
range.
RADIUS server IP address The RADIUS (Remote Access
Dial-In User Service) server provides authentication to
help secure PPPoE connections. Enter the IP address of the
RADIUS server.
RADIUS server key Enter the key shared with the RADIUS
server.
network interface can transmit. The default is 1492 for the
PPPoE connection.
DNS 1 Enter the IP address of the primary remote access
DNS server that your PPPoE client will use.
DNS 2 Enter the IP address of the secondary remote
access DNS server.
Interface Select the appropriate interface that the
EdgeRouter will listen to so it can forward PPPoE requests.
Add Listen Interface You can select multiple interfaces.
To add another interface for PPPoE connections, click
Add Listen Interface. From the new Interface drop-down
menu, select the appropriate interface.
35
Chapter 7: Users Tab EdgeOS
User Guide
Chapter 7: Users Tab
The Users tab displays account information about users.
You can also configure these user accounts. Any setting
You have two sub-tabs:
Local Displays configurable user accounts.
Remote Displays statistics about the users who remotely
access the EdgeRouter.
Local
Configure user accounts with unique logins.
Add User To create a new user, click Add User.
The Create New Local User screen appears.
Username Enter a unique account name for the user.
Full Name Enter the actual name of the user.
Password Enter the password.
Confirm Enter the password again.
Role Select the appropriate permission level:
- Admin The user can make changes to the
EdgeRouter configuration.
- Operator The user can view the EdgeRouter
configuration but cannot make changes.
characters.
user. Click a column heading to sort by that heading.
Username The account name of the user is displayed.
Name The actual name of the user is displayed.
Level The permission level of the user is displayed.
Active Sessions The number of times the user has
accessed the EdgeRouter is displayed.
Date Connected The date of the users most recent
access is displayed.
Uptime The duration of the users access is displayed.
Status The status of the user is displayed.
36
Chapter 7: Users Tab EdgeOS
User Guide
options:
Config To configure the user, click Config. Go to the
Configure the User section below.
Delete Delete the user account; its configuration will be
removed.
Configure the User
After you click Config, the Username screen appears. Make
changes as needed.
Username The unique account name is displayed.
Full Name Enter the actual name of the user.
Role Select the appropriate permission level:
- Admin The user can make changes to the
EdgeRouter configuration.
- Operator The user can view the EdgeRouter
configuration but cannot make changes.
Password Click Change Password to make a change.
- Password Enter the new password.
- Confirm Enter the new password again.
- Cancel Change Password Click this option to cancel.
Remote
Remote access of the EdgeRouter is logged on this tab.
characters.
PPTP/L2TP/PPPOE/All Click the appropriate tab to filter
the remote users as needed.
PPTP All users who use PPTP (Point-to-Point Tunneling
Protocol) connections are displayed.
L2TP All users who use L2TP (Layer 2 Tunneling
Protocol) connections are displayed.
PPPOE All users who use PPPOE (Point-to-Point over
Ethernet) connections are displayed.
All All remote users are displayed by default.
remote user. Click a column heading to sort by that
heading.
Name The actual name of the user is displayed.
Type The type of connection used by the user is
displayed.
Time The duration of the users access is displayed.
Interface The specific interface used by the user is
displayed.
Remote IP The remote IP address of the user is displayed.
TX packets The number of packets transmitted is
displayed.
TX bytes The number of bytes transmitted is displayed.
RXpackets The number of packets received is displayed.
RX bytes The number of bytes received is displayed.
37
Chapter 8: Wizards Tab EdgeOS
User Guide
Chapter 8: Wizards Tab
The Wizards tab allows you to access any available wizards:
Setup Wizards
WAN+2LAN (see the next column)
Feature Wizards
Port Forwarding on page 40
TCP MSS Clamping on page 41
UPnP on page 41
Setup Wizards
The WAN+2LAN setup wizard will guide you through a
typical Small Office Home Office (SOHO) deployment:
Configures the Internet connection and NAT
masquerade for the Internet port
Enables default firewall settings for the Internet port
Enables DHCP server functionality for local networks
Automatically enables DNS (Domain Name System)
forwarding for local networks
Automatically enables TCP MSS (Maximum Segment
Size) clamping for a PPPoE (Point-to-Point over Ethernet)
connection
If the EdgeRouter is already configured, then the
WAN+2LAN setup wizard is not available. It is available only
if the EdgeRouter uses its default configuration.
You can reset the EdgeRouter to its factory defaults using
the EdgeOS Configuration Interface:
System Tab Refer to Reset Config to Default on page
7 for instructions.
Wizards Tab Click the WAN+2LAN setup wizard in the
column on the left. The following window will appear.
Click Reset to Default Configuration and then follow the
on-screen instructions.
WAN+2LAN
Click the WAN+2LAN setup wizard to begin the SOHO
configuration.
Go to the section for your EdgeRouter model:
ERLite-3, ER-8, and ERPro-8 See ERLite-3, ER-8,
ERPro-8 on page 38.
ERPoe-5 See ERPoe-5 on page 39.
Note: The WAN+2LAN setup wizard is designed to
set up a basic SOHO network. For full configuration
functionality, use the other tabs of the EdgeOS
Configuration Interface or the Command Line
Interface (CLI).
38
User Guide
ERLite-3, ER-8, ERPro-8
LAN port (eth0)
Connect eth0 to your local network, such as a switch.
Address The IP address is displayed in the first field,
and the subnet mask or prefix length is displayed in the
second field.
DHCP Select this checkbox to have the EdgeRouter assign
IP addresses.
Internet port (eth1)
Connect eth1 to your Internet connection.
Internet connection type Select the Internet connection
type your network is using.
DHCP Select this option if your Internet Service
Provider (ISP) automatically assigns network settings to
your network.
Static IP Select this option if your ISP has assigned
static network settings to your network.
- Address Enter the IP address in the first field and the
subnet mask or prefix length in the second field.
- Gateway Enter the IP address of the ISPs gateway
server, which provides the point of connection to the
Internet.
- DNS server Enter the IP address of the ISPs DNS
server.
PPPoE Select this option if your ISP uses PPPoE.
- Account Name Enter the name of your PPPoE
account.
- Password Enter the password of your PPPoE account.
Firewall Enabled by default. This option applies
the default firewall settings to the EdgeRouter; only
established and related traffic types are allowed for local
and inbound traffic.
(Optional) Secondary LAN port (eth2)
Click configure this section if you connect eth2 to your
devices and/or a switch.
second field.
IP addresses.
Click Apply to apply your changes, or click Cancel.
39
User Guide
ERPoe-5
Optional Secondary LAN port (eth0)
Click configure this section if you connect eth0 to your
secondary local network.
second field.
IP addresses.
Internet port (eth1)
Connect eth1 to your Internet connection.
Internet connection type Select the Internet connection
type your network is using.
DHCP Select this option if your ISP automatically
assigns network settings to your network.
Static IP Select this option if your ISP has assigned
static network settings to your network.
- Address Enter the IP address in the first field and the
subnet mask or prefix length in the second field.
- Gateway Enter the IP address of the ISPs gateway
server, which provides the point of connection to the
Internet.
- DNS server Enter the IP address of the ISPs DNS
server.
PPPoE Select this option if your ISP uses PPPoE.
- Account Name Enter the name of your PPPoE
account.
- Password Enter the password of your PPPoE account.
Firewall Enabled by default. This option applies
the default firewall settings to the EdgeRouter; only
established and related traffic types are allowed for local
and inbound traffic.
LAN ports (eth2, eth3, and eth4)
Click configure this section if you connect eth2, eth3,
and/or eth4 to your devices and/or a switch. (The eth2,
eth3, and/or eth4 become switch ports for a local network.)
second field.
IP addresses.
40
User Guide
Feature Wizards
Each wizard will guide you through configuration of
the corresponding feature: port forwarding, TCP MSS
clamping, or UPnP.
Port Forwarding
Typically you configure a port forwarding rule so a host on
the external network can access a server on the internal
network by using the public IP address (or hostname) of
the EdgeRouter.
Click the Port Forwarding feature wizard to begin
configuration.
Set Up Port Forwarding
Show advanced options Select this checkbox to display
the Auto firewall option.
WAN interface Select the appropriate interface from
the drop-down menu. (If you select Other, then enter the
interface name in the field provided.)
Hairpin NAT Enabled by default. If you want to allow a
host on the internal network to use the public IP address
to access an internal server, then keep Hairpin NAT
enabled. (Hairpin NAT is also known as NAT loopback or
NAT reflection.)
Note: If Hairpin NAT is enabled, then it only enables
Hairpin NAT for the port forwarding rules defined in
the wizard; it does not affect the Destination NAT
Rules defined on the Security>NATtab (refer to
Destination NAT Rules on page 26).
Auto firewall Enabled by default. The Auto firewall option
is displayed if Show advanced options is enabled. If you
want the EdgeRouter to automatically open ports for the
specified port forwarding rules, then keep Auto firewall
enabled.
If you disable the Auto firewall option, then you will need
to manually define firewall rules on the Security > Firewall
Policies tab (refer to Firewall Policies on page 20).
LAN interface Click Add New to display the drop-down
menu. Then select the appropriate interface. (If you select
Other, then enter the interface name in the field provided.)
Remove Click to delete an interface.
Add New Click to add another new interface.
Port Forwarding Rules
Add New Click to create a new rule.
Original port Enter the port or ports that will be
forwarded to the LAN. You can identify the port or ports
by name, number, and/or range. To specify multiple
ports, use a comma-separated list.
Example: https,20-23,554
Protocol Enter the protocol that will be forwarded to
the LAN: Both, TCP, or UDP.
Forward-to address Enter the LAN IP address that will
receive the forwarded port traffic.
Forward-to port Enter the port or ports that will
receive the forwarded port traffic. You can identify the
port or ports by name, number, and/or range. If you
do not specify the Forward-to port, then the original
destination port of the traffic will be used.
Description Enter keywords that will identify this rule.
Remove Click to delete a rule.
Add New Click to create a new rule.
Click Apply to apply your changes, or click Cancel. To
remove the entire port forwarding configuration created
by the wizard, click Delete.
41
User Guide
TCP MSS Clamping
TCP MSS (Maximum Segment Size) clamping is typically
used when Path MTU Discovery is not working properly.
Using ICMP messages, Path MTU Discovery determines
the highest allowable MTU (Maximum Transmission
Unit) of traffic traveling between two hosts to avoid
fragmentation.
TCP uses MSS, which is the MTU minus the IP and TCP
headers. The sender should limit its data so it does not
exceed the MSS reported by the receiver.
Sometimes security firewalls or other issues interfere
with the Path MTU Discovery process (for example, ICMP
messages are blocked), so you can use a workaround,
TCP MSS clamping, which sets the MSS value for all TCP
connections.
Click the TCP MSS Clamping feature wizard to begin
configuration.
TCP MSS Clamping
Enable MSS clamping for TCP connections Select this
option to specify the MSS value for TCP connections.
Interface Types You can select which interface types use
MSS clamping; PPPoE and PPTP are enabled by default.
MSS Enter the MSS value to use; 1412 is the default.
UPnP
Instead of manually configuring port forwarding rules, you
can use UPnP for automatic port forwarding when you
have hardware that supports UPnP.
Click the UPnP feature wizard to begin configuration.
Set Up UPnP Interfaces
Add New Click to create a new UPnP interface.
Internal interface Select the appropriate LAN interface
from the drop-down menu. (If you select Other, then
enter the interface name in the field provided.)
External interface Select the appropriate WAN
interface from the drop-down menu. (If you select
Other, then enter the interface name in the field
provided.)
Remove Click to delete a UPnP interface.
Add New Click to create another new UPnP interface.
42
Chapter 9: Toolbox EdgeOS
User Guide
Chapter 9: Toolbox
Each tab of the EdgeOS interface contains network
administration and monitoring tools. At the top right of
the screen, click the Toolbox button. The Toolbox
drop-down menu appears.
The following tools are available:
Ping
Trace
Discover
Packet Capture
Log Monitor
Ping
You can ping other devices on the network directly from
the EdgeRouter. The Ping tool uses ICMP packets to check
the preliminary link quality and packet latency estimation
between two network devices.
Destination Host/IP Enter the IP address.
Packet Count Enter the number of packets to send for
the ping test.
Packet Size Specify the size of the packet.
Run Test Click this button to start the test.
Packet loss statistics and latency time evaluation are
displayed after the test is completed.
43
User Guide
Trace
The Trace tool traces the hops from the EdgeRouter to a
specified outgoing IP address. Use this tool to find the
route taken by ICMP packets across the network to the
destination host.
Destination Host Enter the IP address of the destination
host.
Resolve IP Address Select this option to resolve the IP
addresses symbolically (as names) instead of numerically.
Run Test Click this button to start the test.
Responses are displayed after the test is completed.
Discover
The Discover tool searches for all Ubiquiti devices on your
network. The Search field automatically filters devices
containing specified names or numbers as you enter
them.
All/eth_ Select which interface to search, or select All.
The tool reports the number of Discovered and Displayed
Ubiquiti devices. A table displays the following
information about each Ubiquiti device. Click a column
heading to sort by that heading.
Interface The EdgeRouter interface used by the device is
displayed.
Hardware Address The MAC address of the device is
displayed.
Device Name The name assigned to the device is
displayed.
Product Name The Ubiquiti name of the device is
displayed.
IP Address The IP address of the device is displayed. You
can click it to access the devices configuration through its
web management interface.
For more information, click the arrow to view the
following:
Firmware Version The version number of the devices
firmware is displayed.
Uptime The duration of the devices activity is
displayed.
Addresses The addresses of the devices interface are
displayed. If the device has more than one interface,
addresses for each interface are displayed.
- hwaddr The MAC address of the devices interface is
displayed.
- ipv4 The IP address of the devices interface is
displayed.
Packet Capture
Capture packets traveling through the specified interface
for analysis. You can set up filters to capture the specific
types of packets you are seeking.
Interface Enter the name of the interface.
Packet Limit Enter the number of packets to capture. The
maximum number is 300.
Resolve addresses Select this option to resolve the IP
addresses symbolically (as names) instead of numerically.
Filter
Protocol Enter the protocol to filter.
Address Enter the address to filter.
Port Enter the port number to filter.
Negate filter Check this box to capture all packets
except for the ones matching the selected filter(s).
44
User Guide
Start Click this button to start the capture. (If a Packet
Limit is not specified, then this button becomes a Stop
button during the capture.)
Capture results are displayed with Time and Packet
descriptions.
Log Monitor
The Log Monitor is a log displaying live updates.
Click the pause button to stop the live updates. Click the
play button to resume the live updates.
The System log messages table displays the following
information about each log. Click a column heading to
sort by that heading.
Time The system time is displayed next to every log entry
that registers a system event.
Message A description of the system event is displayed.
45
Appendix A: Command Line Interface EdgeOS
User Guide
Appendix A: Command Line
Interface
Overview
The Command Line Interface (CLI) is available if you
need to configure and monitor advanced features on the
EdgeRouter or prefer configuration by command line. The
CLI provides direct access to standard Linux tools and shell
commands. This chapter explains how to access the CLI
and describes a basic set of frequently used commands.
Additional information is available on our website at:
community.ubnt.com/edgemax
Access the CLI
There are four methods you can use to access the CLI:
terminal emulator Go to the following section, Connect
to the Console Port.
SSH If you are using the console port, go to the
following section, Connect to the Console Port; otherwise,
go to Access Using SSH on page 46.
Telnet If you are using the console port, go to the
following section, Connect to the Console Port; otherwise,
go to Access Using Telnet on page 46.
EdgeOS Configuration Interface Go to Access Using
the EdgeOS Configuration Interface on page 47.
Connect to the Console Port
Instructions may vary slightly, depending on your specific
terminal emulator.
1. Use a RJ45-to-DB9, serial console cable, also known
as a rollover cable, to connect the Console port of the
EdgeRouter to your computer. (If your computer does
not have a DB9 port, then you will also need a DB9
adapter.)
eth0 eth1 eth2
Computer
Console
2. Follow the appropriate set of instructions:
terminal emulator Go to the following section,
Access Using a Terminal Emulator.
SSH Go to Access Using SSH on page 46.
Telnet Go to Access Using Telnet on page 46.
Access Using a Terminal Emulator
Instructions may vary slightly, depending on your specific
terminal emulator.
1. Open the terminal emulator on your computer, and
configure it with the following serial port settings:
Baud rate 115200
Data bits 8
Parity NONE
Stop bits 1
Flow control NONE
2. Select Serial as the connection type.
3. Click Open to connect to the EdgeRouter.
4. At the ubnt login prompt, enter the username (the
default is ubnt).
5. At the Password prompt, enter the password (the
default is ubnt).
6. For help with commands, you can either press the ? key
or enter show and press the ? key.
change the default login using one of the following:
Set up a new user account (preferred option).
For details, go to Remove the Default User
Account on page 49.
Change the default password of the ubnt login.
Use the set command as detailed in Remove the
Default User Account on page 49.
46
User Guide
Access Using SSH
SSH is enabled by default.
1. Open the SSH client on your computer.
2. At the login prompt, enter:
ssh <username>@<hostname>
The defaults are ubnt for the username and 192.168.1.1
for the hostname. You can also enter a domain name
instead of an IP address for the hostname.
Note: Upon initial login, a host key will be
displayed. You will be asked to confirm that you
want to save the host key to the local database.
Click Yes to bypass this message in the future.
default is ubnt).
change the default login using at least one of the
following options:
Account on page 49.
Access Using Telnet
Telnet is disabled by default. To use Telnet, enable it on the
System tab (see Telnet Server on page 6).
1. Open the telnet client on your computer.
2. At the prompt, enter:
telnet <hostname>
The default is 192.168.1.1 for the hostname. You can
also enter a domain name instead of an IP address for
the hostname.
3. At the login prompt, enter the username (the default is
ubnt).
default is ubnt).
following options:
Account on page 49.
47
User Guide
Access Using the EdgeOS Configuration
Interface
Each tab of the EdgeOS interface contains CLI access.
1. At the top right of the screen, click the CLI button.
2. The CLI window appears. At the login prompt, enter the
username (the default is ubnt).
default is ubnt).
following options:
Account on page 49.
CLI Modes
Operational Mode
When you first log in, the CLI is in operational mode. Press
the ? key to view the available commands.
ubnt@ubnt:~$
Note: The question mark does not display onscreen.
add delete ping6 reset terminal
clear disconnect reboot restart traceroute
configure generate release set traceroute6
connect initial-setup remove show undebug
copy no rename shutdown
debug ping renew telnet
Enter show and press the ? key to view the settings that
you have configured.
ubnt@ubnt:~$ show
arp flow-accounting nat tech-support
bridge hardware ntp ubnt
configuration history openvpn users
date host pppoe-server version
debugging incoming queueing vpn
dhcp interfaces reboot vrrp
dhcpv6 ip route-map webproxy
disk ipv6 shutdown zebra
dns lldp snmp
file log system
firewall login table
For example, type show interfaces to display the
interfaces and their status information.
ubnt@ubnt:~$ show interfaces
Codes: S - State, L - Link, u - Up, D - Down,
A - Admin Down
Interface IP Address S/L Description
--------- ---------- --- -----------
eth0 - u/u
eth1 - u/D
eth2 - u/D
lo 127.0.0.1/8 u/u
To properly shut down the EdgeRouter, use the shutdown
command.
ubnt@ubnt:~$ shutdown
WARNING: Use the shutdown command to properly
shut down the EdgeRouter. An improper shutdown,
such as disconnecting the EdgeRouter from its
power supply, runs the risk of data corruption!
48
User Guide
Configuration Mode
To switch to configuration mode, use the configure
command.
ubnt@ubnt:~$ configure
[edit]
ubnt@ubnt#
For the show, set, and delete commands, you can press the
? key for help.
set ? View the available commands.
show ? View the settings that you have configured.
(Because configurations vary, the list you see will differ
from the sample list displayed below.)
delete ? View the settings that you can delete.
Enter show and press the ? key.
ubnt@ubnt# show
firewall interfaces protocol service system
[edit]
To display the available command completions, press the
tab key.
Note: The tab does not display onscreen.
ubnt@ubnt# show
Possible completions:
firewall Firewall
interfaces Network interfaces
protocols Routing protocol parameters
service Services
system System parameters
The EdgeRouter uses three configurations:
Working When you make changes to the working
configuration, they are not applied until you commit the
changes to the active configuration.
Active When you commit changes to the active
configuration, they are applied; however, the changes
do not become part of the boot configuration until you
save the changes to the boot configuration.
Boot When the EdgeRouter reboots, it loads the boot
configuration for use.
The following scenarios cover some of the most
commonly used commands:
Configure an Interface (see below)
Remove the Default User Account on page 49
Create a Firewall Rule on page 49
Manage the Configuration File on page 52
Configure an Interface
To configure an interface, do the following:
Assign an IP address and subnet mask
Enter a description
Use the set, compare, commit, and save commands.
To configure an interface, use the set command.
[edit]
To view the possible completions for the eth0 address,
enter set interfaces ethernet eth0 address and press the
? key.
ubnt@ubnt# set interfaces ethernet eth0 address
<x.x.x.x/x> IP address and prefix length
<h:h:h:h:h:h:h:h/x> IPv6 address and prefix length
dhcp Dynamic Host Configuration Protocol
dhcpv6 Dynamic Host Configuration Protocol
for IPv6
[edit]
ubnt@ubnt# set interfaces ethernet eth0 address
10.1.1.80/23
[edit]
ubnt@ubnt# set interfaces ethernet eth0 description
production LAN
These changes affect the working configuration, not the
active configuration. To see what changes have been
made to the working configuration, use the compare
command:
ubnt@ubnt# compare
[edit interfaces ethernet eth0]
+address 10.1.1.2/24
+description production LAN
[edit]
To make the changes active, use the commit command:
ubnt@ubnt# commit
[edit]
If you reboot the EdgeRouter, the changes will be lost. To
save these changes, use the save command to save the
active configuration to the boot configuration.
ubnt@ubnt# save
Saving configuration to /config/config.boot...
Done
[edit]
ubnt@ubnt# exit
exit
ubnt@ubnt:~$
ubnt@ubnt:~$ show interfaces
Codes: S - State, L - Link, u - Up, D - Down,
A - Admin Down
Interface IP Address S/L Description
--------- ---------- --- -----------
eth0 10.1.1.80/23 u/u production LAN
eth1 - u/D
eth2 - u/D
lo 127.0.0.1/8
::1/128
u/u
ubnt@ubnt:$ ping 10.1.0.1
PING 10.1.0.1 (10.1.0.1) 56(84) bytes of data.
64 bytes from 10.1.0.1: icmp_req=1 ttl=64 time=0.460 ms
64 bytes from 10.1.0.1: icmp_req=2 ttl=64 time=0.407 ms
^C
--- 10.1.0.1 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time
999 ms
rtt min/avg/max/mdev = 0.407/0.433/0.460/0.033 ms
49
User Guide
Remove the Default User Account
To remove the default user account, do the following:
Create a new user
Log out of the default user account
Log in with the new user account
Delete the default user account
Use the set, commit, save, exit, and delete commands.
[edit]
ubnt@ubnt:# set system login user admin1 authentication
plaintext-password admin1pass
[edit]
ubnt@ubnt:# commit
[edit]
ubnt@ubnt:# save
Done
[edit]
ubnt@ubnt:# exit
exit
ubnt@ubnt:~$ exit
logout
Welcome to Edge OS ubnt ttyS0
ubnt login: admin1
Password:
Linux ubnt 2.6.32.13-UBNT #1 SMP Fri Jun 8 09:48:31 PDT
2012 mips64
Welcome to EdgeOS
admin1@ubnt:~$ configure
[edit]
admin1@ubnt# delete system login user ubnt
[edit]
admin1@ubnt# commit
[edit]
admin1@ubnt# save
Done
[edit]
admin@ubnt# exit
exit
admin1@ubnt:~$
The plaintext password that you entered is converted to
an encrypted password.
admin1@ubnt:~$ configure
[edit]
admin1@ubnt# show system login
user admin1 {
authentication {
encrypted-password
$1$mv8ERQ1T$7xq/eUDwy/5And7nV.9r6.
plaintext-password

}
}
[edit]
admin1@ubnt# exit
exit
admin1@ubnt:~$
Create a Firewall Rule
To create a firewall rule, use the set or edit commands
(both methods are described below). In addition, use the
compare, discard, up, top, copy, and rename commands.
Create a firewall rule using the full syntax:
[edit]
ubnt@ubnt# set firewall name TEST default-action drop
[edit]
ubnt@ubnt# set firewall name TEST enable-default-log
[edit]
ubnt@ubnt# set firewall name TEST rule 10 description
allow icmp
[edit]
ubnt@ubnt# set firewall name TEST rule 10 action accept
[edit]
ubnt@ubnt# set firewall name TEST rule 10 protocol icmp
[edit]
To display uncommitted changes, use the compare
command:
ubnt@ubnt# compare
[edit firewall]
+name TEST {
+ default-action drop
+ enable-default-log
+ rule 10 {
+ action accept
+ description allow icmp
+ protocol icmp
+ }
+}
[edit]
To undo uncommitted changes, use the discard
command:
ubnt@ubnt# discard
Changes have been discarded
[edit]
ubnt@ubnt# compare
No changes between working and active configurations
[edit]
To create the same firewall rule while reducing the amount
of repetition in the full syntax, use the edit command:
ubnt@ubnt# edit firewall name TEST
[edit firewall name TEST]
ubnt@ubnt#set default-action drop
ubnt@ubnt# set enable-default-log
ubnt@ubnt#edit rule 10
[edit firewall name TEST rule 10]
50
User Guide
Press the ? or tab key to display options for the specified
edit level.
ubnt@ubnt# set
action disable ipsec p2p source time
description fragment limit protocol state
destination icmp log recent tcp
ubnt@ubnt# set description allow icmp
ubnt@ubnt# set action accept
ubnt@ubnt# set protocol icmp
To show changes within the edit level, use the compare
command:
ubnt@ubnt# compare
+action accept
+description allow icmp
+protocol icmp
To move up an edit level, use the up command:
ubnt@ubnt#up
ubnt@ubnt# compare
+default-action drop
+enable-default-log
+rule 10 {
+ action accept
+ protocol icmp
+}
ubnt@ubnt# up
[edit firewall]
ubnt@ubnt# compare
[edit firewall]
+name TEST {
+ rule 10 {
+ action accept
+ protocol icmp
+ }
+}
[edit firewall]
To return to the top edit level, use the top command:
ubnt@ubnt# top
[edit]
ubnt@ubnt# compare
[edit firewall]
+name TEST{
+ rule 10 {
+ action accept
+ protocol icmp
+ }
+}
[edit]
To display the existing firewall rule, use the show firewall
command:
ubnt@ubnt# show firewall
name WAN1_LOCAL {
default-action drop
rule 10 {
action accept
state {
established enable
related enable
}
}
rule 20 {
action drop
state {
invalid enable
}
}
rule 30 {
action accept
destination {
port 22
}
protocol tcp
}
}
[edit]
51
User Guide
To create a new firewall rule from an existing firewall rule,
use the copy command.
ubnt@ubnt# edit firewall
[edit firewall]
ubnt@ubnt# copy name WAN1_LOCAL to name WAN2_LOCAL
[edit firewall]
ubnt@ubnt# commit
[edit firewall]
ubnt@ubnt#top
[edit]
ubnt@ubnt#show firewall
name WAN1_LOCAL {
default-action drop
rule 10 {
action accept
state {
established enable
related enable
}
}
rule 20 {
action drop
state {
invalid enable
}
}
rule 30 {
action accept
destination {
port 22
}
protocol tcp
}
}
name WAN2_LOCAL {
default-action drop
rule 10 {
action accept
state {
established enable
related enable
}
}
rule 20 {
action drop
state {
invalid enable
}
}
rule 30 {
action accept
destination {
port 22
}
protocol tcp
}
}
[edit]
To change the name of the new firewall rule, use the
rename command.
ubnt@ubnt# edit firewall
[edit firewall]
ubnt@ubnt# rename name W[TAB]
WAN1_LOCAL WAN2_LOCAL
[edit firewall]
ubnt@ubnt# rename name WAN2_LOCAL to name WAN2_IN
[edit firewall]
ubnt@ubnt# commit
[edit firewall]
ubnt@ubnt#top
[edit]
ubnt@ubnt# show firewall name
name WAN1_LOCAL {
default-action drop
rule 10 {
action accept
state {
established enable
related enable
}
}
rule 20 {
action drop
state {
invalid enable
}
}
rule 30 {
action accept
destination {
port 22
}
protocol tcp
}
}
name WAN2_IN {
default-action drop
rule 10 {
action accept
state {
established enable
related enable
}
}
rule 20 {
action drop
state {
invalid enable
}
}
rule 30 {
action accept
destination {
port 22
}
protocol tcp
}
}
[edit]
ubnt@ubnt#
52
User Guide
Manage the Configuration File
Typically, you use the save command to save the active
configuration to disk (config/config.boot); however, you
can also save the active configuration to a different file or
remote server.
Enter save and press the ? key.
ubnt@RTR# save
<Enter> Save to system
config file
<file> Save to file on
local machine
scp://<user>:<passwd>@<host>/<file> Save to file on
remote machine
ftp://<user>:<passwd>@<host>/<file> Save to file on
remote machine
tftp://<host>/<file> Save to file on
remote machine
[edit]
ubnt@RTR# save tftp://10.1.0.15/rtr-config.boot
Saving configuration to
tftp://10.1.0.15rtr-config.boot...
############################################### 100.0%
Done
[edit]
Scenario: In the midst of the administrator changing an
IPsec tunnel into an OpenVPN tunnel, the administrator
had to revert the EdgeRouter to its previous configuration
with the IPsec tunnel.
1. Before making changes, the administrator saved a
backup configuration file with a working IPsec tunnel
configuration:
ubnt@RTR# save config.boot-ipsec
Saving configuration to /config/config.boot-ipsec...
Done
[edit]
Note: This is a backup; if the EdgeRouter were
rebooted, it would still boot from the default file:
/config/config.boot
2. After the administrator deleted the IPsec configuration
and was configuring of the OpenVPN tunnel,
circumstances changed so that the IPsec tunnel was
required again. Consequently, the administrator
reverted the EdgeRouter to its previous configuration
with the IPsec tunnel.
ubnt@RTR# load config.boot-ipsec
Loading configuration from
/config/config.boot-ipsec...
Load complete. Use commit to make changes active.
[edit]
ubnt@RTR# commit
[edit]
ubnt@RTR# save; exit
Done
exit
ubnt@RTR:~$
To automatically make a remote backup after every
commit, use the commit-archive configuration option,
enter location, and press the ? key.
ubnt@RTR# set system config-management commit-archive
location
<url> Uniform Resource Identifier
Detailed information:
scp://<user>:<passwd>@<host>/<dir>
ftp://<user>:<passwd>@<host>/<dir>
tftp://<host>/<dir>
ubnt@RTR# set system config-management commit-archive
location tftp://10.1.0.15/RTR
[edit]
ubnt@RTR# commit
Archiving config...
tftp://10.1.0.15/RTR OK
[edit]
On the remote tftp server, a copy with the hostname and
date is saved for each commit.
admin2@server://tftpboot/RTR$ ls -l
total 8
-rw------- 1 nobody nogroup 908 Aug 17 17:19
config.boot-RTR.20120817_171932
-rw------- 1 nobody nogroup 874 Aug 17 17:20
config.boot-RTR.20120818_002046
You can also keep a specified number of revisions
of the configuration file on the local disk. Use the
commit-revisions configuration option.
ubnt@RTR# set system config-management commit-revisions
50
[edit]
ubnt@RTR# commit
[edit]
Here is an example that uses the commit-revisions
command:
ubnt@RTR# set system login user joe authentication
plaintext-password secret
[edit]
ubnt@RTR# commit
[edit]
Done
exit
ubnt@RTR:~$ show system commit
0 2012-08-17 18:32:13 by ubnt via cli commit
2 2012-08-17 18:31:51 by root via init commit
53
User Guide
Note: The following commands require that the
configuration option, commit-revisions, be set first.
show system commit diff commit-confirm
show system commit file confirm
show system commit rollback
commit comment
For details on the commit-revisions option, go to
Manage the Configuration File on page 52.
To display the changes in revision 0, use the show system
commit diff command.
ubnt@RTR:~$ show system commit diff 0
[edit system login]
+user joe {
+ authentication {
+ encrypted-password
$1$CWVzYggs$NyJXxC3S572rfm6pY8ZMO.
+ plaintext-password
+ }
+ level admin
+}
To display the entire configuration file for revision 0, use
the show system commit file command.
ubnt@RTR:~$ show system commit file 0
To add a comment to the commit, use the comment
command.
ubnt@RTR# set system login user joe level operator
[edit]
ubnt@RTR# commit comment change joe from admin to op
[edit]
Done
exit
Now you will see the comment when you use the show
system commit command.
0 2012-08-17 18:44:41 by ubnt via cli change joe
from admin to op
4 2012-08-17 18:31:51 by root via init commit
When you work on a remote router, certain changes,
such as a firewall or NAT rule, can cut off access to the
remote router, so you then have to visit the remote router
and reboot it. To avoid such issues when you make risky
changes, use the commit-confirm command first. Then
use the confirm command to save your changes.
ubnt@RTR:~$ configure
[edit]
ubnt@RTR# set firewall name WAN_IN rule 50 action drop
[edit]
ubnt@RTR# set firewall name WAN_IN rule 50 destination
address 172.16.0.0/16
[edit]
ubnt@RTR# commit-confirm
commit confirm will be automatically reboot in
10 minutes unless confirmed
Proceed? [confirm][y]
[edit]
After you verify that the changes should be saved, use the
confirm command.
ubnt@RTR# confirm
[edit]
You can also specify the number of minutes to wait, but
you must remember to also use the confirm command.
Otherwise, if you forget, then you can be surprised by the
EdgeRouters reboot to its previous configuration.
ubnt@RTR# commit-confirm 1
commit confirm will be automatically reboot in 1 minutes
unless confirmed
Proceed? [confirm][y]
[edit]
ubnt@RTR#
Broadcast message from root@RTR (Mon Aug 20 14:00:06
2012):
The system is going down for reboot NOW!
INIT: Switching to runlevel: 6
INIT: Stopping routing services...zebra...done.
Removing all Quagga Routes.
[SNIP]
To roll back to an earlier commit, use the show system
commit and rollback commands.
0 2012-08-21 14:46:41 by admin_5 via cli
fix bgp policy maps
1 2012-08-21 14:45:59 by admin_5 via cli
commit
2 2012-08-21 14:45:33 by admin_5 via cli
fix port forwarding
3 2012-08-21 14:45:15 by admin_5 via cli
fix firewall
4 2012-08-21 14:44:29 by ubnt via cli
commit
5 2012-08-21 14:21:15 by ubnt via cli
add port forward for port 2222 to build-server
6 2012-08-21 14:20:24 by ubnt via cli
add dmz interface to eth2
7 2012-08-21 14:19:53 by ubnt via cli
add ipsec tunnel to office_exchange
8 2012-08-21 14:07:18 by ubnt via cli
add firewall for WAN_IN
9 2012-08-21 14:06:37 by ubnt via cli
add user first_last
10 2012-08-21 14:04:47 by ubnt via cli
commit
11 2012-08-21 14:04:46 by root via init
commit
After viewing the history of system commits, you decide
to discard the last four commits by admin_5. Roll back the
system configuration file to commit 4:
ubnt@RTR# rollback 4
Proceed with reboot? [confirm] [y]
Broadcast message from root@RTR (ttyS0) (Mon Aug 21
15:09:12 2012):
The system is going down for reboot NOW!
54
Appendix B: Contact Information EdgeOS
User Guide
Appendix B: Contact
Information
Ubiquiti Networks Support
Ubiquiti Support Engineers are located around the world
and are dedicated to helping customers resolve software,
hardware compatibility, or field issues as quickly as
possible. We strive to respond to support inquiries within
a 24-hour period.
Online Resources
Support: support.ubnt.com
Community: community.ubnt.com
Downloads: downloads.ubnt.com
2580 Orchard Parkway
San Jose, CA 95131
www.ubnt.com
2012-2014 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti,
UbiquitiNetworks, the Ubiquiti U logo, the Ubiquiti beam logo,
EdgeMAX, EdgeOS, EdgeRouter, and UniFi are trademarks of Ubiquiti
Networks, Inc. in the United States and in other countries. All other
trademarks are the property of their respectiveowners.
JL020714

EdgeOS User Guide

Uploaded by

Copyright:

Available Formats

EdgeOS User Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

EdgeOS User Guide

Uploaded by

Copyright:

Available Formats

Operating System for Ubiquiti EdgeRouters

Release Version: 1.4

is a powerful, sophisticated operating system

You might also like