FL-1

ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION FL
A
FL
N
O
P
CONTENTS
FUEL SYSTEM
SERVICE INFORMATION ........................ .... 2
PRECAUTIONS .............................................. ..... 2
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................2
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect .....................................2
PREPARATION .............................................. ..... 3
Special Service Tool ........................................... ......3
Commercial Service Tool .................................... ......3
FUEL SYSTEM .................................................... 4
Checking Fuel Line ...................................................4
General Precaution ................................................... 4
FUEL LEVEL SENSOR UNIT, FUEL FILTER
AND FUEL PUMP ASSEMBLY ......................... 5
Component ............................................................... 5
Removal and Installation ..................................... ..... 5
FUEL TANK ....................................................... 9
Component ............................................................... 9
Removal and Installation ..................................... ..... 9
SERVICE DATA AND SPECIFICATIONS
(SDS) .................................................................13
Standard and Limit ..................................................13
Revision: October 2008 2009 Sentra
FL-2
< SERVICE INFORMATION >
PRECAUTIONS
SERVICE INFORMATION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000004406764
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000004741959
NOTE:
This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
Remove and install all control units after disconnecting both battery cables with the ignition knob in the
LOCK position.
Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ACC position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the LOCK position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
Revision: October 2008 2009 Sentra
PREPARATION
FL-3
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
PREPARATION
Special Service Tool INFOID:0000000004406765
The actual shapes of the Kent-Moore tools may differ from those of the special tools illustrated here.
Commercial Service Tool INFOID:0000000004406766
Tool number
(Kent-Moore No.)
Tool name
Description

(J-45722)
130 mm lock ring tool
Removing and installing fuel tank lock ring
LBIA0398E
Tool name Description
Power tools Loosening bolts and nuts
PBIC0190E
Revision: October 2008 2009 Sentra
FL-4
< SERVICE INFORMATION >
FUEL SYSTEM
FUEL SYSTEM
Checking Fuel Line INFOID:0000000004406767
Inspect fuel lines, fuel filler cap and fuel tank for improper attach-
ment, leaks, cracks, damage, loose connections, chafing or deterio-
ration.
If necessary, repair or replace damaged parts.
General Precaution INFOID:0000000004406768
WARNING:
When replacing fuel line parts, be sure to observe the following.
Put a CAUTION: FLAMMABLE sign in the work area.
Be sure to work in a well ventilated area and have a CO2 fire extinguisher.
Do not smoke while working on the fuel system. Keep open flames and sparks away from the work
area.
Put drained fuel in an explosion-proof container and put the lid on securely. Keep the container in
safe area.
CAUTION:
Use gasoline required by the regulations for octane number. Refer to GI-4, "Precaution for Fuel
(Unleaded Regular Gasoline Recommended) Except SE-R Spec-V" or GI-4, "Precaution for Fuel
(Unleaded Premium Gasoline Required) SE-R Spec-V".
Before removing fuel line parts, perform the following procedures:
- Release fuel pressure from the fuel lines. Refer to EC-50, "System Description" MR20DE (California),
EC-596, "System Description" MR20DE (except California), or EC-1161, "Fuel Pressure Check"
QR25DE.
- Disconnect the battery ground cable.
Always replace O-rings and clamps with new ones.
Do not kink or twist tubes when they are being installed.
Perform work on level surface.
Do not tighten hose clamps excessively to avoid damaging hoses.
After connecting fuel tube quick connectors, make sure quick connectors are secure.
Ensure that connector and resin tube do not contact any adjacent parts.
After installing tubes, make sure there is no fuel leakage at connections in the following steps.
- Apply fuel pressure to fuel lines by turning ignition switch ON (without starting the engine). Then
check for fuel leaks at the fuel tube connections.
- Start engine and rev it up and check for fuel leaks at connections.
Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the
MIL may come on.
For servicing Evaporative Emission System parts, refer to EC-50, "System Description" MR20DE
(California), EC-590, "Description" MR20DE (except California), or EC-1111, "Description" QR25DE.
For servicing "On Board Refueling Vapor Recovery (ORVR)" parts, refer to Refer to EC-50, "System
Description" MR20DE (California), EC-596, "System Description" MR20DE (except California), or EC-
1117, "System Description" QR25DE.
SMA803A
Revision: October 2008 2009 Sentra
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-5
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
Component INFOID:0000000004406769
Removal and Installation INFOID:0000000004406770
REMOVAL
WARNING:
Be sure to read General Precautions before working on the fuel system. Refer to GI-3, "General Pre-
caution".
1. Check fuel level with the vehicle on a level surface. If the fuel
gauge indicates more than the level as shown (7/8 full), drain
fuel from the fuel tank until the fuel gauge indicates level as
shown (7/8 full).
NOTE:
Fuel will be spilled when removing fuel pump assembly if fuel
level is above the fuel pump assembly installation surface.
As a guide, fuel level is at the level as shown or below when
approximately 12 (3 1/8 US gal, 2 5/8 Imp gal) of fuel is
drained from a full fuel tank.
In case fuel pump does not operate, perform the following pro-
cedure.
a. Insert fuel tubing of less than 25 mm (0.98 in) in diameter into fuel filler tube through fuel filler opening to
drain fuel from fuel filler tube.
b. Disconnect fuel filler hose from fuel filler tube. Refer to FL-9.
c. Insert fuel tubing into fuel tank through fuel filler hose to drain fuel from fuel tank.
2. Open fuel door and unscrew the fuel filler cap to release the pressure inside the fuel tank.
3. Release the fuel pressure from the fuel lines. Refer to EC-93, "Fuel Pressure Check" MR20DE (Califor-
nia), EC-639, "Fuel Pressure Check" MR20DE (except California), or EC-1161, "Fuel Pressure Check"
QR25DE.
4. Remove rear seat bottom. Refer to SE-19, "Component Parts Drawing" 60/40 Split Fold Down Seat or SE-
24, "Component Parts Drawing" Fixed Back Seat.
1. Lock ring 2. Fuel level sensor unit, fuel filter and fuel pump assembly 3. O-ring
4. Fuel tank
WBIA0804E
KBIA3505J
Revision: October 2008 2009 Sentra
FL-6
< SERVICE INFORMATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
5. Turn the three retainers (A) 90 in a clockwise direction and
remove the fuel pump inspection hole cover.
6. Disconnect electrical connector (A) and fuel feed hose quick
connector (B).
Fuel feed hose (1)
Disconnect the quick connector using the following procedure.
- Hold the sides of the connector, push in tabs and pull out the
tube.
- If quick connector and tube on fuel pump assembly are stuck,
push and pull several times until they move. Disconnect them
by pulling.
CAUTION:
The tube can be removed when the tabs are completely
depressed. Do not twist it more than necessary.
Do not use any tools to remove the quick connector.
Keep resin tube away from heat. Be especially careful
when welding near the resin tube.
Prevent acid liquid such as battery electrolyte, from get-
ting on resin tube.
Do not bend or twist resin tube during installation and removal.
To keep the connecting portion clean, free of foreign
materials and to avoid damage, cover them completely
with plastic bags or something similar.
Do not insert plug to prevent damage to O-ring in quick
connector.
WBIA0805E
WBIA0806E
SFE562A
PBIC0163E
Revision: October 2008 2009 Sentra
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-7
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
7. Remove the lock ring using Tool (A) as shown.
8. Remove fuel level sensor unit, fuel filter and fuel pump assembly
(1).
CAUTION:
Do not bend float arm during removal.
Do not allow foreign materials to fall into fuel tank. Use a
lint free cloth when handling components.
Avoid impacts such as dropping when handling compo-
nents.
INSPECTION AFTER REMOVAL
Make sure that the fuel level sensor unit, fuel filter and fuel pump is free from defects and foreign materials.
INSTALLATION
Installation is in the reverse order of removal.
Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly
1. Install O-ring to fuel tank without twisting.
2. Install fuel level sensor unit, fuel filter and fuel pump assembly
as shown.
Tool number : (J-45722)
WBIA0807E
WBIA0808E
: Vehicle front
WBIA0809E
Revision: October 2008 2009 Sentra
FL-8
< SERVICE INFORMATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
Turn the lock ring (1) using Tool until the lock ring is fully
rotated into the fuel tank lock tabs (A) as shown.
Quick Connector
1. Check the connection for damage or any foreign materials.
2. Align the connector with the tube, then insert the connector straight into the tube until a click sound is
heard.
3. After connecting, make sure that the connection is secure using the following procedure.
Visually confirm that the two retainer tabs are secured to the connector.
Pull the tube and the connector to make sure they are securely
connected.
Inspection Hole Cover
1. Before installing inspection hole cover, confirm that there are no fuel leaks. Refer to FL-9, "Removal and
Installation".
2. Install inspection hole cover with the front mark (arrow) facing
front of vehicle.
3. Lock clips (A) by turning counterclockwise.
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn ignition switch ON (without starting the engine), to check the connections for fuel leaks with the
electric fuel pump applying pressure to the fuel piping.
2. Start the engine and let it idle to check that there are no fuel leaks at the fuel system connections.
Tool number : (J-45722)
WBIA0810E
PBIC1653E
WBIA0805E
Revision: October 2008 2009 Sentra
FUEL TANK
FL-9
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
FUEL TANK
Component INFOID:0000000004406771
Removal and Installation INFOID:0000000004406772
REMOVAL
WARNING:
Be sure to read General Precautions when working on the fuel system. Refer to FL-4, "General Pre-
caution".
1. Drain fuel from fuel tank if necessary. Refer to FL-5, "Removal and Installation".
CAUTION:
Because fuel tank becomes unstable when installing/removing, fuel should be drained if the
level exceeds specification.
Situate vehicle on a flat and solid surface.
2. Open fuel door and unscrew the fuel filler cap to release the pressure inside the fuel tank.
3. Release the fuel pressure from the fuel lines. Refer to EC-93, "Fuel Pressure Check" MR20DE (Califor-
nia), EC-639, "Fuel Pressure Check" MR20DE (except California), or EC-1161, "Fuel Pressure Check"
QR25 DE.
1. Lock ring 2. Fuel level sensor unit, fuel filter and fuel
pump assembly
3. O-ring
4. Fuel tank 5. Fuel tank protector 6. Fuel tank band (LH)
7. Fuel tank band (RH) 8. EVAP hose 9. Hose clamp
10. Fuel filler hose 11. Fuel filler tube 12. Fuel filler shield
13. Grommet 14. Fuel filler cap Front of vehicle
WBIA0811E
Revision: October 2008 2009 Sentra
FL-10
< SERVICE INFORMATION >
FUEL TANK
4. Remove rear seat bottom. Refer to SE-19, "Component Parts Drawing" 60/40 Split Fold Down Seat or SE-
24, "Component Parts Drawing" Fixed Back Seat.
5. Turn the three retainers (A) 90 in a clockwise direction and
remove the fuel pump inspection hole cover.
6. Disconnect electrical connector (A) and fuel feed hose quick
connector (B).
Fuel feed hose (1)
Disconnect the quick connector using the following procedure.
- Hold the sides of the connector, push in tabs and pull out the
tube.
- If quick connector and tube on fuel pump assembly are stuck,
push and pull several times until they move. Disconnect them
by pulling.
CAUTION:
The tube can be removed when the tabs are completely
depressed. Do not twist it more than necessary.
Do not use any tools to remove the quick connector.
Keep resin tube away from heat. Be especially careful
when welding near the resin tube.
Prevent acid liquid such as battery electrolyte, from get-
ting on resin tube.
Do not bend or twist resin tube during installation and removal.
To keep the connecting portion clean, free of foreign
materials and to avoid damage, cover them completely
with plastic bags or something similar.
Do not insert plug to prevent damage to O-ring in quick
connector.
7. Remove center exhaust tube. Refer to EX-4, "Component" MR20DE, or EX-9, "Component" QR25DE.
8. Remove fuel tank protector.
WBIA0805E
WBIA0806E
SFE562A
PBIC0163E
Revision: October 2008 2009 Sentra
FUEL TANK
FL-11
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
9. Loosen fuel filler hose clamp (B) and remove fuel filler hose (1).
CAUTION:
Do not remove fuel filler hose (1) from fuel filler tube. When
removing fuel filler hose (1) at the fuel filler tube, mark com-
ponents for alignment.
10. Remove vent hose (3) and EVAP hose (2) at rear of fuel tank.
Disconnect vent hose and EVAP hose quick connectors using
the following procedures.
a. Pinch retaining tabs (C) of vent hose quick connector and
remove vent hose (3).
b. Pinch retaining tabs (A) of EVAP hose quick connector and
remove EVAP hose (2).
If hoses are stuck, push and pull (A) several times until they
move freely, and disconnect by holding side of connector and
pushing in the tabs (B).
CAUTION:
The tube can be removed when the tabs are completely depressed. Do not twist it more than
necessary.
Do not use any tools to remove the quick connector.
Keep the resin tube away from heat. Be especially careful when welding near the tube.
Prevent acid liquid such as battery electrolyte, from getting on the resin tube.
Do not bend or twist the tube during installation and removal.
Do not insert plug that may cause damage to O-ring in quick connector.
To keep the connecting portion clean and to avoid dam-
age and foreign materials, cover them completely with
plastic bags or something similar.
11. Support center of fuel tank (1) with transmission jack (A) as
shown.
CAUTION:
Securely support the fuel tank with a suitable tool (B).
12. Remove fuel tank bands (RH and LH).
13. Lower transmission jack carefully to remove fuel tank while sup-
porting it by hand as shown.
CAUTION:
Fuel tank may be in an unstable position because of the
shape of fuel tank bottom. Be sure to support tank securely.
INSTALLATION
Installation is in the reverse order of removal.
WBIA0812E
WBIA0831E
PBIC0713E
PBIC3792E
Revision: October 2008 2009 Sentra
FL-12
< SERVICE INFORMATION >
FUEL TANK
EVAP Canister
1. Check the connection for damage or any foreign materials.
2. Align the connector with the tube, then insert the connector straight into the tube until a click sound is
heard.
3. After connecting, make sure that the connection is secure.
Pull the tube and the connector to make sure they are securely connected.
Fuel Tank Band
Install them in the proper position by referring to the identification stamp mark R and L on the end.
Fuel Filler Hose
Insert fuel filler hose (1) to the length (A) below on the fuel tank (3).
Be sure hose clamp (2) is not placed on swelled area of fuel filler
hose (1).
EVAP Hose
1. Check connections for damage or foreign material.
2. Align the matching quick connector (A) with the center of EVAP
hose (1), and insert quick connector (A) straight until it clicks.
3. After connecting, pull on quick connector (A) and EVAP hose (1)
by hand. Make sure connections are secure.
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn ignition switch ON (without starting the engine), to check the connections for fuel leaks with the
electric fuel pump applying pressure to the fuel piping.
2. Start the engine and let it idle to check that there are no fuel leaks at the fuel system connections.
Fuel filler hose installation
on fuel tank (A)
: 35mm (1.38 in)
WBIA0832E
BBIA0873E
Revision: October 2008 2009 Sentra
SERVICE DATA AND SPECIFICATIONS (SDS)
FL-13
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
Standard and Limit INFOID:0000000004406773
FUEL TANK
Unit: (US gal, Imp gal)
Fuel tank capacity 55.0 (14 1/2, 12 1/8)
Fuel specification Refer to MA-14
Revision: October 2008 2009 Sentra