trbl-mx3500n 3501n 4500n 4501n-1
trbl-mx3500n 3501n 4500n 4501n-1
trbl-mx3500n 3501n 4500n 4501n-1
MX3500N
Sv` Huuuu!
[8] SELF DIAG AND TROUBLE CODE
1. SeIf diag
When a trouble occurs in the machine or when the life of a consum-
able part is nearly expired or when the life is expired, the machine
detects and displays it on the display section. This allows the user
and the serviceman to take the suitable action. n case of a trouble,
this feature notifies the occurrence of a trouble and stops the
machine to minimize the damage.
A. Function and purpose
1) Securing safety. (The machine is stopped on detection of a
trouble.)
2) The damage to the machine is minimized. (The machine is
stopped on detection of a trouble.)
3) By displaying the trouble content, the trouble position can be
quickly identified. (This allows to perform an accurate repair,
improving the repair efficiency.)
4) Preliminary warning of running out of consumable parts allows
to arrange for new parts in advance of running out. (This
avoids stopping of the machine due to running out the a con-
sumable part.)
B. SeIf diag message kinds
The self diag messages are classified as shown in the table below.
C. SeIf diag operation and reIated work fIow
The machine always monitors its own state.
When the machine recognizes a trouble, it stops the operation and
displays the trouble message.
A warning message is displayed when a consumable part life is
nearly expired or is expired.
When a warning message is displayed, the machine may be or
may not be stopped.
The trouble messages and the warning messages are displayed by
the LCD.
Some trouble messages are automatically cleared when the trou-
ble is repaired. Some other troubles must be cleared by a simula-
tion.
Some warning messages of consumable parts are automatically
cleared when the trouble is repaired. Some other warning mes-
sages must be cleared by a simulation.
Class 1 User Warning of troubles which can be recovered by
the user. (Paper jam, consumable part life
expiration, etc.)
Serviceman Warning of troubles which can be recovered only
by a serviceman. (Motor trouble, maintenance,
etc.)
Other
Class 2 Warning Warning to the user, not a machine trouble
(Preliminary warning of life expiration of a
consumable part, etc.)
Trouble Warning of a machine trouble. The machine is
stopped.
Other
Troubleshoot the cause.
YES
NO
Detects/analyzes
the content.
Trouble/Warning
Warning
Trouble
The machine is stopped.
The content is displayed.
Trouble/Warning
Warning A consumable
part has reached
its lifetime.
Trouble
Replace or supply
the consumable part.
Cancel the self-
diagnostic message with
the diagnostics
(test commands).
Reset
Standby state
Monitors the machine
conditions.
Repair
SHARP TROUBLE & ERROR CODES
MX-M3500N, MX-M3501N, MX-M4500N, MX-M4501N
MX3500N SELF DAG AND TROUBLE CODE 8 2
D. Breakdown sequence
(1) Breakdown mode Iist
There are following cases of the breakdown mode.
Kind of troubIe
Judgment
bIock
TroubIe code
OperatabIe mode
Copy scan
(incIuding
interruption)
Scan
push
Scan puII
Scan
To
HDD
FAX
send
FAX
print
Print
List
print
Notification
to FAST
host
FAX board trouble MFP F6 1 1 1
(North
America
only)
HDD trouble E7 (03)
SCU communication
trouble
E7 (80), A0-02
PCU communication
trouble
E7 (90), A0-01
L8-20
Backup battery voltage fall U1 (01)
Printer port system trouble F9 (00)
*13 *14
Controller fan motor
trouble
L4-30
Connection trouble (MFP
detection)
E7 (60 65),
A0 (10 12, 20)
Serial number
discrepancy
U2 (30)
Memory error (included
not installed the expansion
RAM)
U2 (00, 05, 10,
11, 22, 23, 24,
25)
Operatable
but send
NG
Process control trouble
(Only history is left.) (MFP
detection)
F2 (80 87)
Laser trouble PCU E7 (20, 28, 29),
L6 (10) * 10
Connection trouble (PCU
detection)
E7 (50, 55),
A0 (21)
PCU section troubles
(motor, fusing, etc.)
H2, H3, H4, H5,
L4 (excluding L4-
30), U2 (90, 91),
F2 (40, 64, 70,
74), L8 (01, 02)
* 10
PCU color system
troubles
E7 (21), F2 (41
43, 65 67, 71
73, 75 77)
* 9 * 9 * 9 * 9 * 9 * 9 * 9 * 9
* 10
* 12
MX3500N SELF DAG AND TROUBLE CODE 8 3
: Operation enabled, : Operation disabled
1: The operation is enabled in a line other than the trouble line.
3: When detected during other than a job, the operation is enabled with a tray other than the trouble tray.
4: When detected during other than a job, the operation is enabled in a section other than the trouble paper exit section. * When, however,
the right tray is set.
* 9: When the color mode is set to Disable in the "Color mode disable setting" of the system setting, the operation is enabled in the Black
mode.
* 10: Since communication is enabled, reception can be transferred.
11: When detected during other than a job, the operation is enabled in other than the DESK.
* 12: Trouble display message is displayed in 2 lines. (Example: Ready to copy. F2 trouble)
*13 : When EF is installed, PCL and GD will not operate. (Machine specifications) (Exclusive)
*14 : Only EF list print (self print) is disabled.
* Trouble mode process
Machine operation enabled under some conditions.
The operations excluding the trouble mode are enabled (READY). For the mode where operations are disabled, only setting is enabled and
the operation disable message is made.
(NOT READY)
(Display) A dialog is displayed when a trouble occurs. For the mode where operations are enabled, [OK] button is added to the message.
When operations are disabled, [OK] button is not displayed, and the message is displayed until the trouble is cancelled.
* For 3, 4, 11, perform the following procedures. (n order to avoid patent interference.)
When a trouble is detected during a job, the machine operation is terminated. (Trouble display/without [OK] key)
When a trouble is detected during other than a JOB, the trouble display is not made and the trouble position cannot be selected. (The dis-
play is not turned off. Machine/Button)
Troubles which disable the machine operations
The trouble display is always made, and all the modes cannot be set.
Writing to the trouble memory
Writing of a same trouble to the trouble memory can be selected with SM 26-35. When this simulation is set, any trouble is written to the
trouble memory unconditionally.
(Sim.26-35)
0: Only once. f same as the previous one, it is not saved. (Default)
1: Any time. Though same as the previous one, it is saved.
Connection trouble (SCU
detection)
SCU E7 (70, 75),
A0 (22)
SCU color system
troubles
UC (02)
Document control trouble UC (20)
EEPROM system U2 (80, 81)
Scanner section troubles
(mirror motor, lens, copy
lamp)
L1, L3
CCD troubles (shading,
etc.)
E7 (10, 11, 14)
Process control trouble
(Only history is left.) (MFP
detection)
MFP F2 (80 87, 90)
Process control trouble
(Only history is left.) (PCU
detection)
PCU F2 (91 94)
Kind of troubIe
Judgment
bIock
TroubIe code
OperatabIe mode
Copy scan
(incIuding
interruption)
Scan
push
Scan puII
Scan
To
HDD
FAX
send
FAX
print
Print
List
print
Notification
to FAST
host
MX3500N SELF DAG AND TROUBLE CODE 8 4
(2) Power ON troubIe detection sequence.
When the power is turned ON and each trouble of H3, H4, H5, U1, U2, PF, U6 (09) is stored, it is judged as a trouble immediately.
2. TroubIe code Iist
TroubIe code
TroubIe code content Remarks
TroubIe
detection
Mechanism Option EIectricity FAX SuppIy Main
code
Sub
code
A0 01 PCU ROM abnormality PCU
02 SCU ROM abnormality Scanner
10 Controller ROM error MFP
11 F version discrepancy (CTL-PCU) MFP
12 F version discrepancy (CTL-SCU) MFP
20 Machine level error (CTL detection) MFP
21 Machine level error (PCU detection) PCU
22 Machine level error (SCU detection) Scanner
CE 00 Communication error other than CE-01 08 The trouble
code is not
displayed,
but only the
message for
each trouble
is displayed.
MFP
01 Network controller trouble MFP
02 Not-specified mail/FTP server error MFP
03 Communication error in image send MFP
04 FTP server account name or authentication password
input error
MFP
05 FTP server directory input error MFP
06 POP3 server access error MFP
07 POP3 server authentication check error MFP
08 POP3 server timeout error MFP
E6 10 Back-face shading trouble black correction (DSPF) Scanner
11 Shading trouble white correction (DSPF) Scanner
14 Back-face ASC communication trouble (DSPF) Scanner
E7 00 System memory access error MFP
01 System data trouble MFP
03 HDD trouble MFP
05 Local memory access error MFP
06 Decode error trouble: Compression decode error (A
compression file cannot decompressed.)
MFP
08 Local memory specifications error MFP
09 Local memory combination error MFP
10 Shading trouble (Black correction) Scanner
11 Shading trouble (White correction) Scanner
14 SCAN-ASC trouble Scanner
(To the corresponding
block)
MFP event
manager
Communication of trouble status
[Trouble code] [Trouble status]
sim task
Trouble cancel command
Trouble cancel status is communicated.
Each block
When the power is turned on,
check is made in each block.
Trouble cancel
(The trouble memory is
initialized.)
(Power ON sequence)
H3, H4, U1, U2, PF, U6 trouble check
(Trouble cancel sequence)
When executing SIM 13, 14, 15, 16, 17
Trouble check is made in each block when initializing
and data are sent to the MFPcnt.
H3, H4, H5: Saved in the MFPcnt.
U1: Saved in the MFPcnt.
U2: Saved in each block.
PF: Saved in the MFPcnt.
U6-09: Saved in the PCU.
SIM 13: U1 trouble cancel
SIM 14: H3, H4, H5 (Color mode
cancel)
SIM 15: LCC (U6) trouble cancel
SIM 16: U2 trouble cancel
SIM 17: PF trouble cancel
MX3500N SELF DAG AND TROUBLE CODE 8 5
E7 20 LSU BD detection trouble PCU
21 LSU LD deterioration trouble PCU
28 LSU control ASC connection abnormality PCU
29 LSU-ASC frequency abnormality PCU
50 Engine connection trouble PCU
55 PWB information sum error (Engine detection) PCU
60 Controller connection trouble (Engine detection) MFP
61 Controller connection trouble (Engine) MFP
62 Controller connection trouble (Scanner) MFP
65 PWB information sum error (Controller detection) MFP
70 Scanner connection trouble SCU
75 PWB information sum error (Scanner detection) SCU
80 Communication trouble between the controller and the
scanner
MFP
90 Communication trouble between the controller and the
engine
MFP
EE EC Auto developer adjustment trouble (The sample level
for every rotation is other than 128 10.)
PCU
EL Auto developer adjustment trouble (overtoner error) PCU
EU Auto development adjustment trouble (Under-toner
abnormality)
PCU
F1 00 Finisher communication trouble (Machine side
detection)
PCU
02 Saddle finisher transport motor trouble PCU
03 Finisher paddle motor trouble (MX-FNX2), finisher
swing motor trouble (MX-FNX1)
PCU
08 Finisher stapler shift motor trouble PCU
10 Finisher staple motor abnormality PCU
11 Finisher bundle process motor abnormality PCU
15 Finisher tray lift motor abnormality PCU
19 Finisher pre-alignment motor abnormality PCU
20 Finisher after-alignment motor abnormality PCU
21 Finisher fan motor abnormality (MX-FNX1), Finisher
interface fan motor abnormality (MX-FNX2)
PCU
31 Finisher folding sensor trouble (MX-FNX2) PCU
32 Communication trouble between the finisher and the
punch unit (MX-FN2)
PCU
33 Finisher punch shift motor trouble PCU
34 Finisher punch motor trouble PCU
35 Finisher punch side registration sensor trouble (MX-
FNX2)
PCU
36 Finisher punch registration sensor trouble (MX-FNX2) PCU
37 Finisher backup RAM trouble PCU
38 Finisher punch backup RAM trouble (MX-FNX2) PCU
39 Finisher punch dust sensor trouble (MX-FNX2) PCU
40 Saddle finisher punch power interruption trouble (MX-
FNX2)
PCU
50 Finisher incompatibility trouble PCU
F2 39 Process thermistor trouble PCU
40 Toner empty sensor abnormality (BLACK) PCU
41 Toner empty sensor abnormality (CYAN) PCU
42 Toner empty sensor abnormality (MAGENTA) PCU
43 Toner empty sensor abnormality (YELLOW) PCU
44 Black exclusive image density sensor trouble (Transfer
belt surface reflection ratio abnormality)
PCU
45 Color exclusive image density sensor trouble
(Calibration plate surface reflection ratio abnormality)
PCU
49 LSU thermistor trouble PCU
50 K phase sensor sensing trouble PCU
51 CL phase sensor sensing trouble PCU
58 Process humidity sensor trouble PCU
64 Toner supply abnormality error (BLACK) PCU
65 Toner supply abnormality error (CYAN) PCU
66 Toner supply abnormality error (MAGENTA) PCU
67 Toner supply abnormality error (YELLOW) PCU
70 Toner cartridge improper cartridge detection (BLACK) PCU
71 Toner cartridge improper cartridge detection (CYAN) PCU
72 Toner cartridge improper cartridge detection
(MAGENTA)
PCU
TroubIe code
TroubIe code content Remarks
TroubIe
detection
Mechanism Option EIectricity FAX SuppIy Main
code
Sub
code
MX3500N SELF DAG AND TROUBLE CODE 8 6
F2 73 Toner cartridge improper cartridge detection
(YELLOW)
PCU
74 Toner cartridge CRUM error (BLACK) PCU
75 Toner cartridge CRUM error (CYAN) PCU
76 Toner cartridge CRUM error (MAGENTA) PCU
77 Toner cartridge CRUM error (YELLOW) PCU
78 Registration exclusive image density sensor trouble
(Transfer belt surface reflection ratio abnormality)
PCU
80 Half tone process control 1st patch reference value
trouble (BLACK)
PCU
81 Half tone process control 1st patch reference value
trouble (CYAN)
PCU
82 Half tone process control 1st patch reference value
trouble (MAGENTA)
PCU
83 Half tone process control 1st patch reference value
trouble (YELLOW)
PCU
84 Half tone process control 2nd patch reference value
trouble (BLACK)
PCU
85 Half tone process control 2nd patch reference value
trouble (CYAN)
PCU
86 Half tone process control 2nd patch reference value
trouble (MAGENTA)
PCU
87 Half tone process control 2nd patch reference value
trouble (YELLOW)
PCU
92 High-density process control density correction error
(CYAN)
PCU
93 High-density process control density correction error
(MAGENTA)
PCU
94 High-density process control density correction error
(YELLOW)
PCU
F3 12 Main unit tray 1 lift-up trouble PCU
22 Main unit tray 2 lift-up trouble PCU
F6 00 Communication trouble between the CU and the FAX Refer to FAX manual for details
01 FAX board EEPROM read/write error
04 FAX MODEM operation trouble
21 Combination error between the TEL/LU PWB and the
FAX soft switch
30 Access error to power controller on the FAX board
(FAX detection)
97 FAX PWB incompatibility trouble
98 Combination error between the FAX-BOX PWB
destination information and the machine destination
information.
F9 00 Communication trouble between the controller and the
printer controller (EF1)
MFP
H2 00 Non-contact thermistor detection thermistor open
(TH_UM_AD2)
PCU
01 Lower thermistor open (TH_LM) PCU
02 Sub thermistor open (TH_US) PCU
03 Non-contact thermistor compensation thermistor open
(TH_UM_AD1)
PCU
04 Hang-up preventing thermistor open (TH-US) PCU
H3 00 Fusing section high temperature trouble (TH_UM) PCU
01 Fusing section high temperature trouble (TH_LM) PCU
02 Sub thermistor fusing section high temperature trouble
(TH_US)
PCU
04 Fusing section high temperature trouble (TH_US) PCU
H4 00 Fusing section low temperature trouble (TH_UM_AD2) PCU
01 Fusing section low temperature trouble (TH_LM) PCU
02 Sub thermistor fusing section low temperature trouble
(TH_US)
PCU
30 Thermistor differential input trouble (TH_UM) PCU
H5 01 5 continuous detection of POD1 not-reached jam PCU
L1 00 Mirror feed trouble Scanner
L3 00 Mirror return trouble Scanner
L4 02 Paper feed motor lock trouble PCU
04 Developing motor trouble (BLACK) PCU
05 Developing motor trouble (COLOR) PCU
06 Transfer belt separation position sensor trouble PCU
11 Shift motor trouble PCU
TroubIe code
TroubIe code content Remarks
TroubIe
detection
Mechanism Option EIectricity FAX SuppIy Main
code
Sub
code
MX3500N SELF DAG AND TROUBLE CODE 8 7
3. DetaiIs of troubIe code
A0-01 PCU ROM abnormaIity
A0-02 SCU ROM abnormaIity
A0-10 ControIIer ROM error
A0-11 IF version discrepancy (CTL-PCU)
L4 30 Controller fan/HDD fan motor trouble MFP
31 Paper exit cooling fan/Toner hopper fan trouble PCU
32 Power cooling fan/ozone exhaust fan trouble PCU
34 LSU cooling fan trouble PCU
L6 10 Polygon motor lock detection LSUcnt
L8 01 No full wave signal PCU
02 Full wave signal width abnormality PCU
20 Power controller communication trouble MFP
PC -- Personal counter not installed MFP
U1 01 Battery trouble MFP
U2 00 EEPROM read/write error (MFP detection) MFP
05 HDD/Flash/EEPROM data discrepancy MFP
10 SRAM user authentication index check sum error MFP
11 EEPROM check sum error (MFP detection) MFP
22 SRAM memory check sum error MFP
23 MFPC section SRAM memory individual data check
sum error
MFP
24 SRAM memory user authentication counter check sum
error
MFP
25 Flash memory user authentication counter check sum
error
MFP
30 Serial number data discrepancy (MFP PCU) MFP
50 HDD section individual data check sum error MFP
80 EEPROM read/write error (SCU detection) Scanner
81 Adjustment value check sum error (SCU detection) Scanner
90 EEPROM read/write error (PCU detection) PCU
91 EEPROM (PCU) check sum error PCU
U5 00 SPF communication trouble Scanner
16 SPF fan motor trouble Scanner
30 SPF tray lift-up trouble Scanner
31 SPF tray lift-down trouble Scanner
40 SPF install trouble Scanner
U6 00 Desk communication trouble PCU
01 Tray 1 lift-up trouble PCU
02 Tray 2 lift-up trouble PCU
09 LCC lift motor trouble PCU
10 Desk transport motor trouble PCU
20 LCC communication trouble PCU
21 LCC transport motor trouble PCU
22 LCC 24V power abnormality PCU
50 Desk incompatibility trouble PCU
51 LCC incompatibility trouble PCU
UC 02 CPT-ASC abnormality Scanner
20 Document control module trouble Scanner
TroubIe code
TroubIe code content Remarks
TroubIe
detection
Mechanism Option EIectricity FAX SuppIy Main
code
Sub
code
Trouble content PCU ROM content trouble
Section PCU
Case 1 Cause Firmware upgrade is not made properly due to power
OFF, etc.
Check
and
remedy
Use SM49-1 to upgrade the firmware.
Trouble content SCU ROM content trouble
Section Scanner
Case 1 Cause Some part of SFU is not upgraded during upgrading of
the firmware.
Check
and
remedy
Use SM49-1 to execute the firmware.
Trouble content SFU combination error in the controller
Section MFP
Case 1 Cause SFU upgrade was not properly made when upgrading
the firmware.
Check
and
remedy
Controller firmware upgrade
Trouble content Combination error between CTL and PCU
Section MFP
Case 1 Cause Combination error between CTL and PCU
Check
and
remedy
Check the firmware combination between CTL and
PCU.
MX3500N SELF DAG AND TROUBLE CODE 8 8
A0-12 IF version discrepancy (CTL-SCU)
A0-20 Machine IeveI error (CTL detection)
A0-21 Machine IeveI error (PCU detection)
A0-22 Machine IeveI error (SCU detection)
CE-00 Communication error other than CE-
01 - 08
CE-01 Network controIIer troubIe
CE-02 Not-specified maiI/FTP server error
CE-03 Communication error in image send
CE-04 FTP server account name or authenti-
cation password input error
Trouble content Combination error between CTL and SCU
Section MFP
Case 1 Cause Combination error between CTL and SCU
Check
and
remedy
Check the firmware combination between CTL and
SCU.
Trouble content Combination error between the machine production/
remodeling and the firmware
Section MFP
Case 1 Cause Combination error between the machine production/
remodeling and the firmware
Check
and
remedy
Check the combination between the machine
production/remodeling and the firmware.
Trouble content Combination error between the machine production/
remodeling and the firmware
Section PCU
Case 1 Cause Combination error between the machine production/
remodeling and the firmware
Check
and
remedy
Check the combination between the machine
production/remodeling and the firmware.
Trouble content Combination error between the machine production/
remodeling and the firmware
Section Scanner
Case 1 Cause Combination error between the machine production/
remodeling and the firmware
Check
and
remedy
Check the combination between the machine
production/remodeling and the firmware.
Trouble content Another communication error occurs.
Section MFP
Case 1 Cause Network cable connection trouble
Check
and
remedy
Check to insure that the network cable is securely
connected.
Trouble content Network controller and its peripheral circuit trouble
Section MFP
Case 1 Cause Network controller and its peripheral circuit trouble
Check
and
remedy
1) Check the network controller and its peripheral
circuit.
2) Output the NC Config Page and check the NC
version.
3) Replace the MFPcnt PWB.
Trouble content The specified mail server, FTP server, and SMB
server are not found
Section MFP
Case 1 Cause Network cable connection trouble
Check
and
remedy
Check to insure that the network cable is securely
connected.
Case 2 Cause Network setup trouble
Check
and
remedy
1) Check that the connected network supports TCP/
P protocol.
2) Check from Web page that the Primary/
Secondary E-mail Server Address or the FTP
server/Desktop PC/SMB server address as the
destination is properly set.
3) When the above address is described with the
Hostname, check that the DNS server is properly
set or not.
Case 3 Cause SMTP server/FTP server/NST/SMB server trouble
Check
and
remedy
Check the SMTP server/FTP server/NST/SMB server
for any trouble.
Trouble content The specified server does not respond during image
send.
Section MFP
Case 1 Cause Network cable connection trouble
Check
and
remedy
Check to insure that the network cable is securely
connected.
Case 2 Cause SMTP server/FTP server/NST/SMB server trouble
Check
and
remedy
Check the SMTP server/FTP server/NST/SMB server
for any trouble.
Trouble content The entered FTP server account name or the
authentication password is invalid.
The entered SMB server log-in name or the password
is invalid.
Section MFP
Case 1 Cause Network cable connection trouble
Check
and
remedy
Check to insure that the network cable is securely
connected.
Case 2 Cause The FTP server account name registered as the
destination or the password for the account is
incorrect.
Check
and
remedy
Check to insure that the FTP server account name
registered as the destination or the password for the
account is correct.
Case 3 Cause The SMB server account name registered as the
destination or the password for the account is
incorrect.
Check
and
remedy
Check to insure that the SMB server account name
registered as the destination or the password for the
account is correct.
MX3500N SELF DAG AND TROUBLE CODE 8 9
CE-05 FTP server directory input error
CE-06 POP3 server access error
CE-07 POP3 server authentication check
error
CE-08 POP3 server timeout error
E6-10 Back-face shading troubIe bIack
correction (DSPF)
E6-11 Shading troubIe white correction
(DSPF)
E6-14 Back-face SCAN-ASIC troubIe
Trouble content The entered FTP server directory is invalid.
The entered SMB server folder is invalid.
Section MFP
Case 1 Cause Network cable connection trouble
Check and
remedy
Check to insure that the network cable is securely
connected.
Case 2 Cause The FTP server account name registered as the
destination or the password for the account is
incorrect.
Check and
remedy
Check to insure that there exits the FTP server
directory registered as the destination.
Case 3 Cause The SMB server account name registered as the
destination or the password for it is incorrect.
Check and
remedy
Check to insure that there exists the SMB server
folder registered as the destination.
Trouble content The specified mail server (POP3) is not found.
(POP3 server access error)
Section MFP
Case 1 Cause Network cable connection trouble
Check and
remedy
Check to insure that the network cable is securely
connected.
Case 2 Cause Network setup error
Check and
remedy
1) Check that the connected network supports
TCP/P protocol.
2) Check the Web page to insure that the POP3
server address is correctly set.
3) f the above address is described in
Hostname, check to insure that the DNS
server is correctly set.
Case 3 Cause PO3 server trouble
Check and
remedy
Check the POP3 server for any trouble.
Trouble content The entered POP3 server account name or the
authentication password is invalid. (POP3 server
authentication check error)
Section MFP
Case 1 Cause Network cable connection trouble
Check and
remedy
Check to insure that the network cable is securely
connected.
Case 2 Cause The POP3 server account name or the password
registered for the account is incorrect.
Check and
remedy
Check to insure that the POP3 server account
name or the password for the account is correct.
Trouble content The specified mail server (POP3) does not
respond. (POP3 server timeout error)
Section MFP
Case 1 Cause Network cable connection trouble
Check and
remedy
Check to insure that the network cable is securely
connected.
Case 2 Cause POP3 server trouble
Check and
remedy
Check the POP3 server for any trouble.
Trouble content CCD black scan level abnormality when the copy
lamp is turned off. (MX-3501N/4501N)
Section Scanner
Case 1 Cause nstallation error of the CCD unit flat cable
Check and
remedy
Check the installing state of the flat cable to the
CCD unit.
Case 2 Cause CCD unit abnormality
Check and
remedy
Check the CCD unit.
Case 3 Cause SCU PWB abnormality
Check and
remedy
Check the SCU PWB.
Trouble content CCD white scan level abnormality when the copy
lamp is on. (MX-3501N/4501N)
Section Scanner
Case 1 Cause nstallation error of the CCD unit flat cable
Check and
remedy
Check the installing state of the flat cable to the
CCD unit.
Case 2 Cause Dirt on the mirror, the lens, or the reference white
plate.
Check and
remedy
Clean the mirror, the lens, or the reference white
plate.
Case 3 Cause Copy lamp lighting trouble
Check and
remedy
Check the installing state of the flat cable to the
copy lamp unit.
Case 4 Cause CCD unit abnormality
Check and
remedy
Check the CCD unit.
Case 5 Cause SCU PWB abnormality
Check and
remedy
Check the SCU PWB.
Trouble content Written register value cannot be read correctly
Section Scanner
Case 1 Cause SCU PWB abnormality
Check and
remedy
Check the SCU PWB.
MX3500N SELF DAG AND TROUBLE CODE 8 10
E7-00 System memory access error
* When E7-00 is in the following combination where system mem-
ory Slot 2 (inside) and Slot 1 (outside) operate normally but a
hard error occurs. (Combination of system memory (slot 1, slot 2)
E7-01 System data troubIe
E7-03 HDD troubIe
E7-05 LocaI memory access error
* Combination where local memory Slot 4 (inside) and Slot 3 (out-
side) operate normally (Refer to E7-09) but a hard error occurs.
E7-06 Decode error troubIe: Compression
decode error (A compression fiIe
cannot decompressed.)
E7-08 LocaI memory specifications error
* The error occurs when a DMM which is not recommended by
Sharp.
Trouble content System memory trouble (Tandem memory cannot be
guaranteed.)
Access to system memory cannot be made.
Section MFP
Case 1 Cause Expansion memory instillation error
Check
and
remedy
Check installation of the system expansion memory.
Case 2 Cause Garbled data
Check
and
remedy
1) Use SM60-01 to check memory read/write
2) Replace the expansion memory (if installed.)
3) Replace the MFPcnt PWB.
Case 3 Cause Dirt on the memory pin
Check
and
remedy
Clean the memory pin with alcohol.
No.
System memory Operation guarantee
When turning
on the power
SIot2
(Inside)
SIot1
(Outside)
Hard Soft
1 Since the
machine is not
booted, the
trouble display is
not made.
2 256MB Normal operation
3 512MB Normal operation
4 256MB 256MB Normal operation
5 512MB 256MB Normal operation
6 256MB 512MB Normal operation
7 512MB 512MB Normal operation
8 256MB Normal operation
9 512MB Normal operation
Trouble content CU data trouble occurs.
Section MFP
Case 1 Cause CU image transfer trouble
Check
and
remedy
1) Check the connection state of the MFPcnt PWB
connector.
2) Replace the MFPcnt PWB.
Trouble content HDD connection trouble
File control area data trouble (when FAT is broken)
Section MFP
Case 1 Cause The HDD is not properly installed to the MFPcnt PWB
Check
and
remedy
1) Check installation of the HDD of the MFPcnt
PWB.
2) Check connection of the harness of the MFPcnt
PWB.
3) Use SM62-2 and -3 to check read/write from/to
the HDD.
Case 2 Cause The HDD does not work properly.
Check
and
remedy
Replace the HDD.
Case 3 Cause MFPcnt PWB trouble
Check
and
remedy
Replace the MFPcnt PWB.
Trouble content Local memory cannot be accessed.
Section MFP
Case 1 Cause Local memory installation abnormality
Check
and
remedy
Check the installing state of the local memory.
Case 2 Cause Dirt on local memory pin
Check
and
remedy
Clean the local memory pin with alcohol.
Case 3 Cause Garbled data
Check
and
remedy
1) Use SM60-01 to check memory read/write.
2) Replace the memory.
3) Replace the MFPcnt PWB.
Trouble content A decode error occurs when forming an image.
Section MFP
Case 1 Cause Compression data abnormality
Check
and
remedy
1) Check the installing state of the PWB. (PC bus)
2) When an error occurs during a FAX job, check
the installation of the FAX PWB. n the other
cases, check the installation of the MFPcnt PWB
and HDD.
3) Replace the MFPcnt PWB.
Case 2 Cause HDD connection abnormality
Check
and
remedy
Check the HDD connection.
Case 3 Cause Data are garbled in image compression/send.
Check
and
remedy
1) Check the installation of the PWB. (PC bus)
2) When an error occurs during a FAX job, check
the installation of the FAX PWB. n the other
cases, check the installation of the MFPcnt PWB
and HDD.
3) Replace the MFPcnt PWB.
Case 4 Cause MFPcnt PWB abnormality
Check
and
remedy
Replace the MFPcnt PWB.
Case 5 Cause Local memory access trouble
Check
and
remedy
Check and execute remedy similarly to E7-05.
Trouble content DMM of different specification is detected in the local
memory slot.
Section MFP
Case 1 Cause DMM of different specification is installed to the local
memory slot.
Check
and
remedy
Check the installed DMM.
MX3500N SELF DAG AND TROUBLE CODE 8 11
E7-09 LocaI memory combination error
* When the following combination (E7-09) where operation is not
performed properly is used. Local memory (slot 3, slot 4) combi-
nation
E7-10 Shading troubIe (BIack correction)
E7-11 Shading troubIe (White correction)
E7-14 SCAN-ASIC troubIe
E7-20 LSU BD detection troubIe
E7-21 LSU LD deterioration troubIe
Trouble content Local memory slot combination error
Section MFP
Case 1 Cause DMM of other than 256MB is installed to the default
slot.
Check
and
remedy
Check the combination of installed DMM.
Case 2 Cause DMM of other than 256MB is installed to the
expansion slot.
Check
and
remedy
Check the combination of installed DMM.
No.
LocaI memory Operation guarantee
When turning
on the power
SIot 4
(Inside)
SIot 3
(Outside)
Hard Soft
1 E7-09
2 256MB Normal operation
3 512MB E7-09
4 256MB 256MB E7-09
5 512MB 256MB E7-09
6 256MB 512MB Normal operation
7 512MB 512MB E7-09
8 256MB E7-09
9 512MB E7-09
Trouble content CCD black scan level abnormality when the copy lamp
is turned off.
Section Scanner
Case 1 Cause nstallation error of the CCD unit flat cable
Check
and
remedy
Check the installing state of the flat cable to the CCD
unit.
Case 2 Cause CCD unit abnormality
Check
and
remedy
Check the CCD unit.
Case 3 Cause SCU PWB abnormality
Check
and
remedy
Check the SCU PWB.
Trouble content CCD white scan level abnormality when the copy lamp
is on.
Section Scanner
Case 1 Cause nstallation error of the CCD unit flat cable
Check
and
remedy
Check the installing state of the flat cable to the CCD
unit.
Case 2 Cause Dirt on the mirror, the lens, or the reference white
plate.
Check
and
remedy
Clean the mirror, the lens, or the reference white plate.
Case 3 Cause Copy lamp lighting trouble
Check
and
remedy
Check the installing state of the flat cable to the copy
lamp unit.
Case 4 Cause CCD unit abnormality
Check
and
remedy
Check the CCD unit.
Case 5 Cause SCU PWB abnormality
Check
and
remedy
Check the SCU PWB.
Trouble content Written register value cannot be read correctly
Section Scanner
Case 1 Cause SCU PWB abnormality
Check
and
remedy
Check the SCU PWB.
Trouble content LSU BD signal is not detected.
Section PCU
Case 1 Cause Disconnection or improper connection of harness and
connector between LD/BD PWB and LSUcnt PWB
Check
and
remedy
Check connection of the harness of each PWB inside
the LSU.
Case 2 Cause 1) Optical axis shift
2) BK laser deterioration, power reduction
3) BD PWB trouble
Check
and
remedy
1) Use SM61-1 to check the LSU operation.
2) Replace the LSUcnt/BD PWB.
3) f the trouble cannot be removed by the above 1)
to 2), replace the LSU.
Trouble content The color laser does not light up normally.
Section PCU
Case 1 Cause Disconnection or improper connection of harness and
connector between LD PWB and LSUcnt PWB
Check
and
remedy
Check connection of the harness of each PWB inside
the LSU.
Case 2 Cause Y/M/C laser deterioration
Check
and
remedy
1) Use SM61-1 to check the LSU operation.
2) Replace the LSUcnt PWB.
3) f the trouble cannot be removed by the above 1)
to 2), replace the LSU.
MX3500N SELF DAG AND TROUBLE CODE 8 12
E7-28 LSU controI ASIC connection abnor-
maIity
E7-29 LSU-ASIC frequency abnormaIity
E7-50 Engine connection troubIe
E7-55 PWB information sum error
(Engine detection)
E7-60 ControIIer connection troubIe
(Engine detection)
E7-61 ControIIer connection troubIe
(Engine)
E7-62 ControIIer connection troubIe
(Scanner)
E7-65 PWB information sum error
(ControIIer detection)
E7-70 Scanner connection troubIe
Trouble content Access error between the CPU of the PCU PWB
and the LSU control ASC
Section PCU
Case 1 Cause <When this trouble occurs in the initial process on
turn on the power>
Communication connector trouble between the
PCU PWB and the LSUcnt PWB (interface PWB).
Harness trouble.
Check and
remedy
Check the connector connection between the PCU
PWB and the LSUcnt PWB (interface PWB).
Check the harness. f the trouble cannot be
removed, replace the LSUcnt PWB or the PCU
PWB.
Case 2 Cause <When this trouble occurs on starting printing/
during printing, and SM61-1 is used to check the
LSU unit operation for each of B/W and COLOR
and the judgment is NG.>
Connected the connector between the PCU PWB
and the LSUcnt PWB (interface PWB) / Harness
trouble
Check and
remedy
Check the harness between the PCU PWB and the
LSUcnt PWB (interface PWB). f the trouble cannot
be removed, replace the LSUcnt PWB or the PCU
PWB.
Case 3 Cause PCU PWB or LSUcnt PWB (interface PWB)
trouble
Check and
remedy
Replace the PCU PWB or the LSUcnt PWB
(interface PWB).
Trouble content Oscillation trouble of the external oscillator used in
LSU-ASC and the internal oscillation circuit
Section PCU
Case 1 Cause Trouble of the oscillator on the LSU-ASC PWB,
the resistor and capacitor for the oscillation circuit,
and the LSU-ASC itself.
Check and
remedy
Replace the LSUcnt PWB.
Trouble content Unknown PWB identification information is
detected in the PCU PWB.
Section PCU
Case 1 Cause A PWB which is incompatible with the machine
specifications is connected.
Check and
remedy
1) Replace the PCU PWB.
2) Replace the LSU PWB.
Case 2 Cause A firmware which is incompatible with the machine
specifications is used.
Check and
remedy
Check the kind and the version of the firmware.
Trouble content EEPROM PWB information sum error
Section PCU
Case 1 Cause 1) EEPROM device error
2) EEPROM device contact failure
3) Device access error due to noises
Check and
remedy
Replace the PCU PWB.
Trouble content Unknown PWB kind information is detected in the
MFPcnt PWB.
A PWB/firmware which is not compatible with the
machine specifications is connected.
Section MFP
Case 1 Cause Controller PWB trouble
Check and
remedy
Replace the controller PWB.
Case 2 Cause A firmware which is not compatible with the
machine specifications is applied.
Check and
remedy
Check the kind and the version of the firmware.
Trouble content MFPcnt PWB connection trouble
Compatibility trouble between the controller and
the engine
Section MFP
Case 1 Cause Combination trouble of the controller PWB and the
engine
Check and
remedy
Check the controller PWB.
Check the combination between the controller
PWB and the engine.
Trouble content Controller connection trouble
Compatibility trouble between the controller and
the scanners
Section MFP
Case 1 Cause Combination trouble between the controller PWB
and the engine
Check and
remedy
Replace the controller PWB.
Check the combination between the controller
PWB and the engine.
Trouble content EEPROM PWB information sum error
Section MFP
Case 1 Cause 1) EEPROM device trouble
2) EEPROM device contact failure
3) Device access error due to noises
Check and
remedy
Replace the MFPcnt PWB.
Trouble content Unknown identification information is detected in
the SCU PWB.
Section SCU
Case 1 Cause SCU PWB trouble
Check and
remedy
Replace the SCU PWB.
Case 2 Cause A firmware which is incompatible with the machine
specifications is connected.
Check and
remedy
Check the kind and the version of the firmware.
MX3500N SELF DAG AND TROUBLE CODE 8 13
E7-75 PWB information sum error
(Scanner detection)
E7-80 Communication troubIe between the
controIIer and the scanner
E7-90 Communication troubIe between the
controIIer and the engine
EE-EC Auto deveIoper adjustment troubIe
(The sampIe IeveI for every rotation is
other than 128 10).
EE-EL Auto deveIoper adjustment troubIe
(overtoner error)
EE-EU Auto deveIopment adjustment troubIe
(Under-toner abnormaIity)
F1-00 Finisher communication troubIe
(Machine side detection)
F1-02 SaddIe finisher transport motor
troubIe
Trouble content EEPROM PWB information sum error
Section SCU
Case 1 Cause 1) EEPROM device trouble
2) EEPROM device contact failure
3) Device access error due to noises
Check and
remedy
Replace the scanner control PWB.
Trouble content Communication trouble between the MFP and the
scanner MFP detection
Communication establishment error/Framing/
Parity/Protocol error
Section MFP
Case 1 Cause SCU PWB connector connection trouble
Check and
remedy
Check the connector connection between the SCU
PWB and the MFPcnt PWB.
Case 2 Cause Harness trouble between the SCU PWB and the
MFPcnt PWB
Check and
remedy
Check the harness between the SCU PWB and
the MFPcnt PWB.
Case 3 Cause Broken connector pin of the SCU PWB mother
board
Check and
remedy
Check grounding of the machine.
Trouble content Communication trouble between the MFP and the
PCU (MFP detection)
Communication establishment error/Framing/
Parity/Protocol error
Section MFP
Case 1 Cause PCU PWB connector connection trouble
Check and
remedy
Check the connector connection between the PCU
PWB and the MFPcnt PWB.
Case 2 Cause Harness trouble between the PCU PWB and the
MFPcnt PWB
Check and
remedy
Check the harness between the PCU PWB and
the MFPcnt PWB.
Case 3 Cause Broken connector pin of the PCU PWB mother
board
Check and
remedy
Check grounding of the machine.
Trouble content Auto developer adjustment trouble (The sample
level for every rotation is other than 128 10.)
<Detection only with SM25-2, no trouble memory,
only display>
Section PCU
Case 1 Cause Toner density sensor trouble, charging voltage/
developing voltage trouble, toner density trouble,
developing unit trouble, PCU PWB trouble
Check and
remedy
Use SM25-2 to execute the auto development
adjustment.
Trouble content The sample level is 76 or below, or the control
voltage is 208V or above. <Detection only with
SM25-2, no trouble memory, only display>
Section PCU
Case 1 Cause Toner density sensor trouble, charging voltage/
developing voltage trouble, toner density trouble,
developing unit trouble, PCU PWB trouble
Check and
remedy
Use SM25-2 to execute the auto development
adjustment.
Trouble content The sample level is 178 or above, or the control
voltage is 51V or below. <Detection only with
SM25-2, no trouble memory, only display>
Section PCU
Case 1 Cause Toner density sensor trouble, charging voltage/
developing voltage trouble, toner density trouble,
developing unit trouble, PCU PWB trouble
Check and
remedy
Use SM25-2 to execute the auto development
adjustment.
Trouble content Communication line test error when turning on the
power or after canceling an exclusion simulation.
Communication error with the finisher
Section PCU
Case 1 Cause Malfunction due to noises
Check and
remedy
Turn OFF/ON the power to cancel.
Case 2 Cause PCU finisher connector or harness connection
error or disconnection
Check and
remedy
Check the connector and harness in the
communication line.
Case 3 Cause Finisher control PWB trouble
Check and
remedy
Replace the finisher control PWB.
Case 4 Cause Control PWB (PCU) trouble
Check and
remedy
Replace the PCU PWB.
Trouble content Transport drive motor trouble
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, motor
overvoltage, saddle finisher control PWB trouble
Check and
remedy
Use SM3-3 to check the operation of the transport
motor (FFM).
Replace the finisher control PWB.
MX3500N SELF DAG AND TROUBLE CODE 8 14
F1-03 Finisher paddIe motor troubIe (MX-
FNX2), finisher swing motor troubIe
(MX-FNX1)
F1-08 Finisher stapIer shift motor troubIe
F1-10 Finisher stapIe motor abnormaIity
F1-11 Finisher bundIe process motor
abnormaIity
F1-15 Finisher tray Iift motor abnormaIity
F1-19 Finisher pre-aIignment motor
abnormaIity
F1-20 Finisher after-aIignment motor
abnormaIity
F1-21 Finisher fan motor abnormaIity (MX-
FNX1), Finisher interface fan motor
abnormaIity (MX-FNX2)
F1-31 Finisher foIding sensor troubIe
(MX-FNX2)
F1-32 Communication troubIe between the
finisher and the punch unit (MX-FN2)
F1-33 Finisher punch shift motor troubIe
Trouble content Paddle motor operation trouble (MX-FNX2)
Swing motor operation trouble (MX-FNX1)
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, motor
overvoltage, finisher control PWB trouble
Check and
remedy
Use SM3-3 to check the operation of the motor
(FPM/FSWM).
Replace the finisher control PWB.
Trouble content Stapler shift motor operation trouble
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, motor
overvoltage, finisher control PWB trouble
Check and
remedy
Use SM3-3 to check the operation of the staple
motor (FSM).
Replace the finisher control PWB.
Trouble content Staple operation trouble
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, motor
overvoltage, saddle finisher control PWB trouble
Check and
remedy
Use SM3-3 to check the operation of the staple
motor (FFSM).
Replace the finisher control PWB.
Trouble content Bundle process motor trouble
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, motor
overvoltage, finisher control PWB trouble (MX-
FNX2)
Check and
remedy
Use SM3-3 to check the operation of the bundle
process motor (FAM).
Replace the finisher control PWB.
Trouble content Lift motor trouble
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, motor
overvoltage, finisher control PWB trouble
Check and
remedy
Use SM3-3 to check the operation of the tray lift
motor (FLM/FTLM).
Replace the finisher control PWB.
Trouble content Pre-alignment motor trouble
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, motor
overvoltage, saddle finisher control PWB trouble
Check and
remedy
Use SM3-3 to check the operation of the pre-
alignment motor (FFJM).
Replace the finisher control PWB.
Trouble content After-alignment motor trouble
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, motor
overvoltage, finisher control PWB trouble
Check and
remedy
Use SM3-3 to check the operation of the after-
alignment motor (FRJM).
Replace the finisher control PWB.
Trouble content Cooling fan motor trouble (MX-FNX1)
nterface transport fan motor trouble (MX-FNX2)
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, motor
overvoltage, finisher control PWB trouble
Check and
remedy
Use SM3-3 to check the operation of the fan
motor (FFAM/FJFM).
Replace the finisher control PWB.
Trouble content Sensor input value abnormality
Section PCU
Case 1 Cause Sensor breakage, harness disconnection, finisher
control PWB trouble (MX-FNX2)
Check and
remedy
Use SM3-2 to check the operation of the sensor
(FFPD).
Replace the finisher control PWB.
Trouble content Finisher and punch unit communication trouble
(MX-FNX2)
Section PCU
Case 1 Cause Malfunction due to noises
Check and
remedy
Cancel by turning OFF/ON the power.
Case 2 Cause Connector/harness connection error or
disconnection between the finisher and the punch
unit
Check and
remedy
Check the connector and the harness in the
communication line.
Case 3 Cause Finisher control PWB trouble (MX-FNX2)
Check and
remedy
Replace the finisher control PWB.
Case 4 Cause Control PWB (PCU) trouble
Check and
remedy
Replace the control PWB (PCU) trouble
Trouble content Punch shift motor operation abnormality
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, motor
overvoltage, finisher control PWB trouble, punch
control PWB trouble (MX-FNX2)
Check and
remedy
Use SM3-3 to check the operation of the punch
shift motor (FPSM).
Replace the finisher punch unit (Replace the
punch control PWB.).
MX3500N SELF DAG AND TROUBLE CODE 8 15
F1-34 Finisher punch motor troubIe
F1-35 Finisher punch side registration sen-
sor troubIe (MX-FNX2)
F1-36 Finisher punch registration sensor
troubIe (MX-FNX2)
F1-37 Finisher backup RAM troubIe
F1-38 Finisher punch backup RAM troubIe
(MX-FNX2)
F1-39 Finisher punch dust sensor troubIe
(MX-FNX2)
F1-40 SaddIe finisher punch power
interruption troubIe (MX-FNX2)
F1-50 Finisher incompatibiIity troubIe
F2-39 Process thermistor troubIe
F2-40 Toner empty sensor abnormaIity
(BLACK)
Trouble content Punch motor operation abnormality
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, motor
overvoltage, finisher control PWB trouble, punch
control PWB trouble (MX-FNX2)
Check and
remedy
Use SM3-3 to check the operation of the punch
motor (FPNW).
Replace the finisher punch unit (Replace the
punch control PWB.).
Trouble content Sensor input value abnormality
Section PCU
Case 1 Cause Sensor breakage, harness disconnection, saddle
finisher control PWB trouble (MX-FNX2), punch
control PWB trouble (MX-FNX2)
Check and
remedy
Use SM3-2 to check the operation of the punch
section sensor (FPSHPD/FPSD1-4).
Replace the finisher punch unit (Replace the
punch control PWB.).
Trouble content Sensor input value abnormality
Section PCU
Case 1 Cause Sensor breakage, harness disconnection, saddle
finisher control PWB trouble (MX-FNX2), punch
control PWB trouble (MX-FNX2)
Check and
remedy
Use SM3-2 to check the operation of the punch
timing sensor (FPTD).
Replace the finisher punch unit (Replace the
punch control PWB.).
Trouble content Backup RAM data garbled
Section PCU
Case 1 Cause Finisher control PWB trouble, malfunction due to
electrical noises
Check and
remedy
Replace the finisher control PWB.
Trouble content Punch unit backup RAM data garbled
Section PCU
Case 1 Cause Punch control PWB trouble, malfunction due to
electrical noises
Check and
remedy
Replace the punch control PWB.
Trouble content Punch dust sensor detection trouble
Section PCU
Case 1 Cause Sensor breakage, harness disconnection, finisher
control PWB trouble (MX-FNX2), punch control
PWB trouble (MX-FNX2)
Check and
remedy
Use SM3-2 to check the operation of the sensor
punch dust sensor (FPDD).
Replace the finisher control PWB or the punch
control PWB.
Trouble content When the punch unit power interruption is
detected.
Section PCU
Case 1 Cause Harness disconnection, punch control PWB
trouble
Check and
remedy
Use SM3-3 to check the operation punch motor
(FPNW).
Replace the finisher punch unit (Replace the
punch control PWB.).
Trouble content Detection of finisher incompatible with MX-3500**/
4500**/3501**/4501**
Section PCU
Case 1 Cause Connection of the AR-F13, etc. which is
incompatible with MX-3500**/4500**/3501**/
4501** is detected.
Check and
remedy
Connect the MX-FNX1/MX-FNX2.
Trouble content Process thermistor open
Section PCU
Case 1 Cause Process thermistor harness connection trouble
Check and
remedy
Check the connection of the harness, connector of
the process thermistor.
Case 2 Cause Process thermistor trouble
Check and
remedy
Check the connection of the process thermistor.
Case 3 Cause PCU PWB trouble
Check and
remedy
Check the PCU PWB.
Trouble content Toner empty sensor output abnormality. Sample
level 25 or less or 231 or above.
Section PCU
Case 1 Cause The connector is not installed.
Check and
remedy
Check the connection of the connector harness to
the PCU PWB. Check the connection of the toner
empty sensor.
Case 2 Cause Connector harness trouble
Check and
remedy
Check the harness disconnection.
Case 3 Cause Cartridge trouble
Check and
remedy
Check the cartridge connection.
MX3500N SELF DAG AND TROUBLE CODE 8 16
F2-41 Toner empty sensor abnormaIity
(CYAN)
F2-42 Toner empty sensor abnormaIity
(MAGENTA)
F2-43 Toner empty sensor abnormaIity
(YELLOW)
F2-44 BIack excIusive image density sensor
troubIe (Transfer beIt surface
refIection ratio abnormaIity)
F2-45 CoIor excIusive image density sensor
troubIe (CaIibration pIate surface
refIection ratio abnormaIity)
F2-49 LSU thermistor troubIe
Trouble content Toner empty sensor output abnormality. Sample level
25 or less or 231 or above.
Section PCU
Case 1 Cause The connector is not installed.
Check
and
remedy
Check the connection of the connector harness to the
PCU PWB. Check the connection of the toner empty
sensor.
Case 2 Cause Connector harness trouble
Check
and
remedy
Check the harness disconnection.
Case 3 Cause Cartridge trouble
Check
and
remedy
Check the cartridge connection.
Trouble content Toner empty sensor output abnormality. Sample level
25 or less or 231 or above.
Section PCU
Case 1 Cause The connector is not installed.
Check
and
remedy
Check the connection of the connector harness to the
PCU PWB. Check the connection of the toner empty
sensor.
Case 2 Cause Connector harness trouble
Check
and
remedy
Check the harness disconnection.
Case 3 Cause Cartridge trouble
Check
and
remedy
Check the cartridge connection.
Trouble content Toner empty sensor output abnormality. Sample level
25 or less or 231 or above.
Section PCU
Case 1 Cause The connector is not installed.
Check
and
remedy
Check the connection of the connector harness to the
PCU PWB. Check the connection of the toner empty
sensor.
Case 2 Cause Connector harness trouble
Check
and
remedy
Check the harness disconnection.
Case 3 Cause Cartridge trouble
Check
and
remedy
Check the cartridge connection.
Trouble content The transfer belt surface is scanned by the image
density sensor before starting the process control, and
adjust the sensor gain so that the output is kept at a
certain level. However, the output is not within the
specified range though the senor gain is adjusted.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU PWB and the image density
sensor, image density sensor dirt, transfer belt
cleaning trouble, calibration plate solenoid operation
trouble
Check
and
remedy
Use SM44-2 to execute the process control sensor
gain adjustment. f "ERROR" is displayed, check the
sensor, the harness, the calibration plate solenoid
operation for any trouble. f the adjustment is
completed, check the transfer belt surface state.
Trouble content The calibration plate surface is scanned by the image
density sensor before starting the process control, and
adjust the sensor gain so that the output is kept at a
certain level. However, the output is not within the
certain level though the senor gain is adjusted.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU PWB and the image density
sensor, image density sensor dirt, calibration plate
dirt, calibration plate solenoid operation trouble
Check
and
remedy
Use SM44-2 to execute the process control gain
adjustment. f "ERROR" is displayed, check the
sensor and the harness. f the adjustment is
completed, check the calibration plate solenoid
operation.
Trouble content The detection temperature is out of the range of 5C
to 55C.
Section PCU
Case 1 Cause LSU thermistor harness connection trouble
Check
and
remedy
Check the connection of the LSU thermistor harness
and connector.
f the trouble cannot be removed, replace the LSU
thermistor or the PCU PWB.
Case 2 Cause LSU thermistor trouble, PCU PWB trouble
Check
and
remedy
Check the PCU PWB.
f the trouble cannot be removed, replace the LSU
thermistor or the PCU PWB.
MX3500N SELF DAG AND TROUBLE CODE 8 17
F2-50 K phase sensor sensing troubIe
F2-51 CL phase sensor sensing troubIe
F2-58 Process humidity sensor troubIe
F2-64 Toner suppIy abnormaIity (BLACK)
F2-65 Toner suppIy abnormaIity (CYAN)
F2-66 Toner suppIy abnormaIity (MAGENTA)
Trouble content Detection is made by interruption of light in the sensor
section of the projection rib on the drum drive gear to
control the BK drum phase. The detection signal
cannot be acquired and phase control cannot be
made.
Section PCU
Case 1 Cause Sensor connector connection trouble
Check
and
remedy
Check the sensor connector connection.
Case 2 Cause Dirt on the sensor light emitting section, or installation
trouble
Check
and
remedy
Check for dirt on the sensor or check the installation
state.
Case 3 Cause Drum drive gear upper rib breakage, sensor trouble
Check
and
remedy
f there is no trouble in the rib, replace the sensor.
(Use SM30-1 "DHPD_K" to check interruption or
transmission of light.)
Trouble content Detection is made by interruption of light in the sensor
section of the projection rib on the drum drive gear to
control the phases of all the color drums. The
detection signal cannot be acquired and phase control
cannot be made.
Section PCU
Case 1 Cause Sensor connector connection trouble
Check
and
remedy
Check the sensor connector connection.
Case 2 Cause Dirt on the sensor light emitting section, or installation
trouble
Check
and
remedy
Check for dirt on the sensor or check the installation
state.
Case 3 Cause Drum drive gear upper rib breakage, sensor trouble
Check
and
remedy
f there is no trouble in the rib, replace the sensor.
(Use SM30-1 "DHPD_CL" to check interruption or
transmission of light.)
Trouble content Process humidity sensor open
Section PCU
Case 1 Cause Process humidity sensor harness connection trouble
Check
and
remedy
Check the harness and connector connection of the
process humidity sensor.
Case 2 Cause Process humidity sensor trouble
Check
and
remedy
Check the process humidity sensor.
Case 3 Cause PCU PWB trouble
Check
and
remedy
Check the PCU PWB.
Trouble content Toner end with the remaining quantity of 50% or more.
The toner supply time exceeds 3 times as much as
the specified time.
Section PCU
Case 1 Cause Toner motor section connector harness trouble
Check
and
remedy
Check the connector connection of the toner motor
section.
Check the connector harness (TM) connection to the
main PWB.
Case 2 Cause Toner motor and toner density sensor trouble
Check
and
remedy
Check the toner density sensor output. (SM25-1)
Check that the toner transport pipe is not clogged
between the toner cartridge and the developing unit.
Replace the toner cartridge (CRUM) if necessary.
f replacement of the toner cartridge (CRUM) does not
clear the trouble, check the developing unit.
Trouble content Toner end with the remaining quantity of 50% or more.
The toner supply time exceeds 3 times as much as
the specified time.
Section PCU
Case 1 Cause Toner motor section connector harness trouble
Check
and
remedy
Check the connector connection of the toner motor
section.
Check the connector harness (TM) connection to the
main PWB.
Case 2 Cause Toner motor and toner density sensor trouble
Check
and
remedy
Check the toner density sensor output. (SM25-1)
Check that the toner transport pipe is not clogged
between the toner cartridge and the developing unit.
Replace the toner cartridge (CRUM) if necessary.
f replacement of the toner cartridge (CRUM) does not
clear the trouble, check the developing unit.
Trouble content Toner end with the remaining quantity of 50% or more.
The toner supply time exceeds 3 times as much as
the specified time.
Section PCU
Case 1 Cause Toner motor section connector harness trouble
Check
and
remedy
Check the connector connection of the toner motor
section.
Check the connector harness (TM) connection to the
main PWB.
Case 2 Cause Toner motor and toner density sensor trouble
Check
and
remedy
Check the toner density sensor output. (SM25-1)
Check that the toner transport pipe is not clogged
between the toner cartridge and the developing unit.
Replace the toner cartridge (CRUM) if necessary.
f replacement of the toner cartridge (CRUM) does not
clear the trouble, check the developing unit.
MX3500N SELF DAG AND TROUBLE CODE 8 18
F2-67 Toner suppIy abnormaIity (YELLOW)
F2-70 Toner cartridge improper cartridge
detection (BLACK)
F2-71 Toner cartridge improper cartridge
detection (CYAN)
F2-72 Toner cartridge improper cartridge
detection (MAGENTA)
F2-73 Toner cartridge improper cartridge
detection (YELLOW)
F2-74 Toner cartridge CRUM error (BLACK)
F2-75 Toner cartridge CRUM error (CYAN)
F2-76 Toner cartridge CRUM error
(MAGENTA)
Trouble content Toner end with the remaining quantity of 50% or more.
The toner supply time exceeds 3 times as much as
the specified time.
Section PCU
Case 1 Cause Toner motor section connector harness trouble
Check
and
remedy
Check the connector connection of the toner motor
section.
Check the connector harness (TM) connection to the
main PWB.
Case 2 Cause Toner motor and toner density sensor trouble
Check
and
remedy
Check the toner density sensor output. (SM25-1)
Check that the toner transport pipe is not clogged
between the toner cartridge and the developing unit.
Replace the toner cartridge (CRUM) if necessary.
f replacement of the toner cartridge (CRUM) does not
clear the trouble, check the developing unit.
Trouble content mproper data are detected in the CRUM contents
when the normal CRUM of the cartridge is detected.
Section PCU
Case 1 Cause An improper cartridge is inserted. Toner cartridge
trouble
Check
and
remedy
Replace the toner cartridge.
Trouble content mproper data are detected in the CRUM contents
when the normal CRUM of the cartridge is detected.
Section PCU
Case 1 Cause An improper cartridge is inserted. Toner cartridge
trouble
Check
and
remedy
Replace the toner cartridge.
Trouble content mproper data are detected in the CRUM contents
when the normal CRUM of the cartridge is detected.
Section PCU
Case 1 Cause An improper cartridge is inserted. Toner cartridge
trouble
Check
and
remedy
Replace the toner cartridge.
Trouble content mproper data are detected in the CRUM contents
when the normal CRUM of the cartridge is detected.
Section PCU
Case 1 Cause An improper cartridge is inserted. Toner cartridge
trouble
Check
and
remedy
Replace the toner cartridge.
Trouble content CRUM cannot be read or written.
Section PCU
Case 1 Cause Connection trouble or disconnection of the connector
and the harness between the PCU and the toner
cartridge.
Check
and
remedy
Check the connector and the harness between the
PCU and the toner cartridge.
Case 2 Cause CRUM trouble
Check
and
remedy
Replace the toner cartridge.
Case 3 Cause Control PWB (PCU) trouble
Check
and
remedy
Replace the PCU PWB.
Trouble content CRUM cannot be read or written.
Section PCU
Case 1 Cause Connection trouble or disconnection of the connector
and the harness between the PCU and the toner
cartridge.
Check
and
remedy
Check the connector and the harness between the
PCU and the toner cartridge.
Case 2 Cause CRUM trouble
Check
and
remedy
Replace the toner cartridge.
Case 3 Cause Control PWB (PCU) trouble
Check
and
remedy
Replace the PCU PWB.
Trouble content CRUM cannot be read or written.
Section PCU
Case 1 Cause Connection trouble or disconnection of the connector
and the harness between the PCU and the toner
cartridge.
Check
and
remedy
Check the connector and the harness between the
PCU and the toner cartridge.
Case 2 Cause CRUM trouble
Check
and
remedy
Replace the toner cartridge.
Case 3 Cause Control PWB (PCU) trouble
Check
and
remedy
Replace the PCU PWB.
MX3500N SELF DAG AND TROUBLE CODE 8 19
F2-77 Toner cartridge CRUM error
(YELLOW)
F2-78 Registration excIusive image density
sensor troubIe (Transfer beIt surface
refIection ratio abnormaIity)
F2-80 HaIf tone process controI 1st patch
reference vaIue troubIe (BLACK)
F2-81 HaIf tone process controI 1st patch
reference vaIue troubIe (CYAN)
F2-82 HaIf tone process controI 1st patch
reference vaIue troubIe (MAGENTA)
F2-83 HaIf tone process controI 1st patch
reference vaIue troubIe (YELLOW)
Trouble content CRUM cannot be read or written.
Section PCU
Case 1 Cause Connection trouble or disconnection of the connector
and the harness between the PCU and the toner
cartridge.
Check
and
remedy
Check the connector and the harness between the
PCU and the toner cartridge.
Case 2 Cause CRUM trouble
Check
and
remedy
Replace the toner cartridge.
Case 3 Cause Control PWB (PCU) trouble
Check
and
remedy
Replace the PCU PWB.
Trouble content The transfer belt surface is scanned by the image
density sensor before starting the registration, and
adjust the sensor gain so that the output is kept at a
certain level. However, the output is not within the
specified range though the senor gain is adjusted.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU PWB and the image density
sensor, image density sensor dirt, transfer belt
cleaning trouble, calibration plate solenoid operation
trouble
Check
and
remedy
Check the sensor and the harness. Check the
calibration plate solenoid operation and the transfer
belt surface state.
f the trouble is not cleared, replace the image sensor
exclusively used for registration, replace the transfer
belt, replace the calibration plate, replace the
solenoid, or replace the PCU PWB according to the
check result.
Trouble content The low-density rising point or the high-density
saturation point cannot be calculated because of a
calculation error in the primary approximation formula
of the sensor output ratio for the LSU PWM value
obtained from the first step patch print result when
executing the half tone process control in BLACK.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU sub PWB and the image density
sensor, image density sensor dirt, transfer belt
cleaning trouble
Check
and
remedy
Use SM44-2 to execute the process control gain
adjustment. f "ERROR" is displayed, check the
sensor and the harness. f the adjustment is
completed, check the drum surface state and the belt
surface state.
Trouble content The low-density rising point or the high-density
saturation point cannot be calculated because of a
calculation error in the primary approximation formula
of the sensor output ratio for the LSU PWM value
obtained from the first step patch print result when
executing the half tone process control in CYAN.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU sub PWB and the image density
sensor, image density sensor dirt, transfer belt
cleaning trouble
Check
and
remedy
Use SM44-2 to execute the process control gain
adjustment. f "ERROR" is displayed, check the
sensor and the harness. f the adjustment is
completed, check the drum surface state and the belt
surface state.
Trouble content The low-density rising point or the high-density
saturation point cannot be calculated because of a
calculation error in the primary approximation formula
of the sensor output ratio for the LSU PWM value
obtained from the first step patch print result when
executing the half tone process control in MAGENTA.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU sub PWB and the image density
sensor, image density sensor dirt, transfer belt
cleaning trouble
Check
and
remedy
Use SM44-2 to execute the process control gain
adjustment. f "ERROR" is displayed, check the
sensor and the harness. f the adjustment is
completed, check the drum surface state and the belt
surface state.
Trouble content The low-density rising point or the high-density
saturation point cannot be calculated because of a
calculation error in the primary approximation formula
of the sensor output ratio for the LSU PWM value
obtained from the first step patch print result when
executing the half tone process control in YELLOW.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU sub PWB and the image density
sensor, image density sensor dirt, transfer belt
cleaning trouble
Check
and
remedy
Use SM44-2 to execute the process control gain
adjustment. f "ERROR" is displayed, check the
sensor and the harness. f the adjustment is
completed, check the drum surface state and the belt
surface state.
MX3500N SELF DAG AND TROUBLE CODE 8 20
F2-84 HaIf tone process controI 2nd patch
reference vaIue troubIe (BLACK)
F2-85 HaIf tone process controI 2nd patch
reference vaIue troubIe (CYAN)
F2-86 HaIf tone process controI 2nd patch
reference vaIue troubIe (MAGENTA)
F2-87 HaIf tone process controI 2nd patch
reference vaIue troubIe (YELLOW)
F2-92 High-density process controI density
correction error (CYAN)
F2-93 High-density process controI density
correction error (MAGENTA)
Trouble content The low-density section output is greater than the
middle-density section output when connecting the
low-density section approximation formula and the
middle-density section approximation formula
(formula of the sensor output ratio for the LSU PWM
value) from the second step patch print result when
executing the half tone process control in BLACK.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU sub PWB and the image density
sensor, image density sensor dirt, transfer belt
cleaning trouble, transfer belt cleaning trouble
Check
and
remedy
Use SM44-2 to execute the process control gain
adjustment. f "ERROR" is displayed, check the
sensor and the harness. f the adjustment is
completed, check the drum surface state and the belt
surface state.
Trouble content The low-density section output is greater than the
middle-density section output when connecting the
low-density section approximation formula and the
middle-density section approximation formula
(formula of the sensor output ratio for the LSU PWM
value) from the second step patch print result when
executing the half tone process control in CYAN.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU sub PWB and the image density
sensor, image density sensor dirt, transfer belt
cleaning trouble
Check
and
remedy
Use SM44-2 to execute the process control gain
adjustment. f "ERROR" is displayed, check the
sensor and the harness. f the adjustment is
completed, check the drum surface state and the belt
surface state.
Trouble content The low-density section output is greater than the
middle-density section output when connecting the
low-density section approximation formula and the
middle-density section approximation formula
(formula of the sensor output ratio for the LSU PWM
value) from the second step patch print result when
executing the half tone process control in MAGENTA.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU sub PWB and the image density
sensor, image density sensor dirt, transfer belt
cleaning trouble
Check
and
remedy
Use SM44-2 to execute the process control gain
adjustment. f "ERROR" is displayed, check the
sensor and the harness. f the adjustment is
completed, check the drum surface state and the belt
surface state.
Trouble content The low-density section output is greater than the
middle-density section output when connecting the
low-density section approximation formula and the
middle-density section approximation formula (formula
of the sensor output ratio for the LSU PWM value)
from the second step patch print result when
executing the half tone process control in YELLOW.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU sub PWB and the image density
sensor, image density sensor dirt, transfer belt
cleaning trouble
Check
and
remedy
Use SM44-2 to execute the process control gain
adjustment. f "ERROR" is displayed, check the
sensor and the harness. f the adjustment is
completed, check the drum surface state and the belt
surface state.
Trouble content The patch density value is not in the range of the
density correction reference density value (STD
value) 30% at the upper limit or the lower limit bias
voltage when executing the high density process
control.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU PWB-image density sensor, dirt
on image density sensor, transfer belt cleaning trouble
Check
and
remedy
1) Use SM44-2 to execute the process control
sensor gain adjustment.
2) f an error occurs, check the sensors and the
harnesses.
3) f the adjustment of 1) is completed, check the
drum surface state, the belt surface state, etc.
Trouble content The patch density value is not in the range of the
density correction reference density value (STD
value) 30% at the upper limit or the lower limit bias
voltage when executing the high density process
control.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU PWB-image density sensor, dirt
on image density sensor, transfer belt cleaning trouble
Check
and
remedy
1) Use SM44-2 to execute the process control
sensor gain adjustment.
2) f an error occurs, check the sensors and the
harnesses.
3) f the adjustment of 1) is completed, check the
drum surface state, the belt surface state, etc.
MX3500N SELF DAG AND TROUBLE CODE 8 21
F2-94 High-density process controI density
correction error (YELLOW)
F3-12 Main unit tray 1 Iift-up troubIe
F3-22 Main unit tray 2 Iift-up troubIe
F9-00 Communication troubIe between the
controIIer and the printer controIIer
(EF1)
H2-00 Non-contact thermistor detection
thermistor open (TH_UM_AD2)
H2-01 Lower thermistor open (TH_LM)
H2-02 Sub thermistor open (TH_US)
H2-03 Non-contact thermistor
compensation thermistor open
(TH_UM_AD1)
H2-04 Hang-up preventing thermistor open
(TH-US)
Trouble content The patch density value is not in the range of the
density correction reference density value (STD
value) 30% at the upper limit or the lower limit bias
voltage when executing the high density process
control.
Section PCU
Case 1 Cause mage density sensor trouble, harness connection
trouble between PCU PWB-image density sensor, dirt
on image density sensor, transfer belt cleaning trouble
Check
and
remedy
1) Use SM44-2 to execute the process control
sensor gain adjustment.
2) f an error occurs, check the sensors and the
harnesses.
3) f the adjustment of 1) is completed, check the
drum surface state, the belt surface state, etc.
Trouble content LUD1 does not turn ON within the specified time.
Section PCU
Case 1 Cause LUD1 sensor trouble, harness connection trouble
between PCU PWB, the lift-up unit, and the paper
feed unit.
Check
and
remedy
Check the harness and the connector of LUD1.
Case 2 Cause Tray 1 lift-up motor trouble
Check
and
remedy
Check the lift-up unit.
Trouble content LUD2 does not turn ON within the specified time.
Section PCU
Case 1 Cause LUD2 sensor trouble, harness connection trouble
between PCU PWB, the lift-up unit, and the paper
feed unit.
Check
and
remedy
Check the harness and the connector of LUD2.
Case 2 Cause Tray 2 lift-up motor trouble
Check
and
remedy
Check the lift-up unit.
Trouble content A communication error is detected during initial
establishment or after establishment of
communication with the EF controller.
Section MFP
Case 1 Cause Printer controller MFPcnt PWB cable trouble
Check
and
remedy
Check the printer controller MFPcnt PWB cable.
Case 2 Cause MFPcnt PWB cable trouble, printer controller PWB
trouble
Check
and
remedy
Replace the MFPcnt PWB. Repair or replace the
printer controller PWB.
After completion of check, turn OFF/ON the machine
and the printer controller.
Trouble content Thermistor open
Section PCU
Case 1 Cause Thermistor trouble, control PWB trouble, fusing
section connector connection trouble, AC power
source trouble, fusing unit not-installed
Check
and
remedy
Check the harness and the connector from the
thermistor to the control PWB.
Trouble content Thermistor open
Section PCU
Case 1 Cause Thermistor trouble, control PWB trouble, fusing
section connector connection trouble, AC power
source trouble, fusing unit not-installed
Check
and
remedy
Check the harness and the connector from the
thermistor to the control PWB.
Trouble content Thermistor open
Section PCU
Case 1 Cause Thermistor trouble, control PWB trouble, fusing
section connector connection trouble, AC power
source trouble, fusing unit not-installed
Check
and
remedy
Check the harness and the connector from the
thermistor to the control PWB.
Trouble content Thermistor open
Section PCU
Case 1 Cause Thermistor trouble, control PWB trouble, fusing
section connector connection trouble, AC power
source trouble
Check
and
remedy
Check the harness and the connector from the
thermistor to the control PWB.
Trouble content Thermistor open
Section PCU
Case 1 Cause Thermistor trouble, control PWB trouble, fusing
section connector connection trouble, AC power
source trouble
Check
and
remedy
Check the harness and the connector from the
thermistor to the control PWB.
MX3500N SELF DAG AND TROUBLE CODE 8 22
H3-00 Fusing section high temperature
troubIe (TH_UM)
H3-01 Fusing section high temperature trou-
bIe (TH_LM)
H3-02 Sub thermistor fusing section high
temperature troubIe (TH_US)
H3-04 Fusing section high temperature
troubIe (TH_US)
H4-00 Fusing section Iow temperature
troubIe (TH_UM_AD2)
H4-01 Fusing section Iow temperature
troubIe (TH_LM)
Trouble content The fusing temperature inside the PWB exceeds the
specified level.
Section PCU
Case 1 Cause Thermistor trouble, control PWB trouble, fusing
section connector connection error, AC power source
trouble
Check
and
remedy
1) Use SM5-2 to check blinking of the heater lamp.
2) f it blinks normally, check the thermistor and the
harness.
Check the control PWB thermistor input circuit
section.
3) f the heater lamp keep lighting, check the AC
PWB and the control PWB lamp control circuit.
4) Use SM14 to cancel the trouble.
Trouble content The fusing temperature inside the PWB exceeds the
specified level.
Section PCU
Case 1 Cause Thermistor trouble, control PWB trouble, fusing
section connector connection error, AC power source
trouble
Check
and
remedy
1) Use SM5-2 to check blinking of the heater lamp.
2) f it blinks normally, check the thermistor and the
harness.
Check the control PWB thermistor input circuit
section.
3) f the heater lamp keep lighting, check the AC
PWB and the control PWB lamp control circuit.
4) Use SM14 to cancel the trouble.
Trouble content The fusing temperature inside the PWB exceeds the
specified level.
Section PCU
Case 1 Cause Thermistor trouble, control PWB trouble, fusing
section connector connection error, AC power source
trouble
Check
and
remedy
1) Use SM5-2 to check blinking of the heater lamp.
2) f it blinks normally, check the thermistor and the
harness.
Check the control PWB thermistor input circuit
section.
3) f the heater lamp keep lighting, check the AC
PWB and the control PWB lamp control circuit.
4) Use SM14 to cancel the trouble.
Trouble content The temperature of the hung-up prevention thermistor
exceeds the specified level.
Section PCU
Case 1 Cause Non-contact thermistor trouble, control PWB trouble,
fusing section connector connection error, AC power
source trouble
Check
and
remedy
1) Use Sim44-14 to check if the non-contact
thermistor shows an abnormal temperature. f
the display is normal, use Sim5-2 to check the
blinking operation of the heater lamp.
a) f it blinks normally, check the thermistor
and the harness.
Check the control PWB thermistor input
circuit section.
b) f the heater lamp keep lighting, check the
AC PWB and the control PWB lamp control
circuit.
2) Use SM14 to cancel the trouble.
Trouble content The temperature does not reach the specified level
within the specified time after turning on the power
relay.
Section PCU
Case 1 Cause Thermistor trouble, heater lamp trouble, PCU PWB
trouble, thermostat trouble, AC power source trouble,
interlock switch trouble
Check
and
remedy
1) Use SM5-2 to check blinking of the heater lamp.
2) f it blinks normally, check the thermistor and the
harness.
Check the control PWB thermistor input circuit
section.
3) f it is not lighted, check for the heater lamp
disconnection and the thermostat breakage.
Check the interlock switch. Check the AC PWB
and the PCU PWB lamp control circuit.
4) Use SM14 to cancel the trouble.
Trouble content The temperature does not reach the specified level
within the specified time after turning on the power
relay.
Section PCU
Case 1 Cause Thermistor trouble, heater lamp trouble, PCU PWB
trouble, thermostat trouble, AC power source trouble,
interlock switch trouble
Check
and
remedy
1) Use SM5-2 to check blinking of the heater lamp.
2) f it blinks normally, check the thermistor and the
harness.
Check the control PWB thermistor input circuit
section.
3) f it is not lighted, check for the heater lamp
disconnection and the thermostat breakage.
Check the interlock switch. Check the AC PWB
and the PCU PWB lamp control circuit.
4) Use SM14 to cancel the trouble.
MX3500N SELF DAG AND TROUBLE CODE 8 23
H4-02 Sub thermistor fusing section Iow
temperature troubIe (TH_US)
H4-30 Thermistor differentiaI input troubIe
(TH_UM)
H5-01 5 continuous detection of POD1 not-
reached jam
L1-00 Mirror feed troubIe
L3-00 Mirror return troubIe
L4-02 Paper feed motor Iock troubIe
L4-04 DeveIoping motor troubIe (BLACK)
L4-05 DeveIoping motor troubIe (COLOR)
Trouble content The temperature does not reach the specified level
within the specified time after turning on the power
relay.
Section PCU
Case 1 Cause Thermistor trouble, heater lamp trouble, PCU PWB
trouble, thermostat trouble, AC power source trouble,
interlock switch trouble
Check
and
remedy
1) Use SM5-2 to check blinking of the heater lamp..
2) f it blinks normally, check the thermistor and the
harness.
Check the control PWB thermistor input circuit
section.
3) f it is not lighted, check for the heater lamp
disconnection and the thermostat breakage.
Check the interlock switch. Check the AC PWB
and the PCU PWB lamp control circuit.
4) Use SM14 to cancel the trouble.
Trouble content TH_UM_AD1 and TH_UM_AD2 do not exceed the
specified level (50 count with the AD value) within
1minute after HL_UM is turned on.
Section PCU
Case 1 Cause HL_UM does not turn on. Thermistor trouble, harness
trouble, PCU PWB trouble
Check
and
remedy
1) Use SM5-2 to check blinking of the heater lamp.
2) f it blinks normally, check the thermistor and the
harness.
Check the PCU PWB thermistor input circuit
section.
3) f it is not lighted, check for the heater lamp
disconnection and the thermostat breakage.
Check the interlock switch. Check the AC PWB
and the PCU PWB lamp control circuit.
4) Use SM14 to cancel the trouble.
Trouble content 5 continuous detection of POD1 not-reached jam
Section PCU
Case 1 Cause The fusing jam is not removed completely. (Jam paper
remains.)
Check
and
remedy
Check the fusing section for jam paper. (winding, etc.)
Case 2 Cause POD1 sensor trouble or harness connection trouble
Check
and
remedy
Check the POD1 sensor harness. Use SM14 to
cancel the trouble.
Case 3 Cause Fusing unit installation trouble
Check
and
remedy
Check the fusing unit installation.
Trouble content Mirror feed is not completed within the specified time.
Section Scanner
Case 1 Cause Mirror unit trouble, mirror wire disengagement
Check
and
remedy
Use SM1-1 to check the mirror operation.
Trouble content Mirror return is not completed within the specified
time.
Section Scanner
Case 1 Cause Mirror unit trouble, mirror wire disengagement
Check
and
remedy
Use SM1-1 to check the mirror operation.
Trouble content When the paper feed motor is rotated in warming up
or in canceling a jam and the lock signal is not
detected within 1sec.
Section PCU
Case 1 Cause Paper feed motor trouble, harness connection trouble
between PCU PWB and paper feed motor, control
circuit trouble
Check
and
remedy
Use SM6-1 to check the paper feed motor operation.
Check the harness and the connector between the
PCU PWB and the paper feed motor.
Trouble content The motor lock signal is detected during rotation of the
developing motor.
Section PCU
Case 1 Cause Harness connection trouble between the PCU PWB
and the developing motor.
Check
and
remedy
Check the harness and the connector between the
PCU PWB and the developing motor.
Case 2 Cause Developing motor trouble, control circuit trouble
Check
and
remedy
Use SM25-1 to check the operation of the developing
motor.
Trouble content The motor lock signal is detected during rotation of the
developing motor.
Section PCU
Case 1 Cause Harness connection trouble between the PCU PWB
and the developing motor.
Check
and
remedy
Check the harness and the connector between the
PCU PWB and the developing motor.
Case 2 Cause Developing motor trouble, control circuit trouble
Check
and
remedy
Use SM25-1 to check the operation of the developing
motor.
MX3500N SELF DAG AND TROUBLE CODE 8 24
L4-06 Transfer beIt separation position
sensor troubIe
L4-11 Shift motor troubIe
L4-30 ControIIer fan/HDD fan motor troubIe
L4-31 Paper exit cooIing fan/Toner hopper
fan troubIe
L4-32 Power cooIing fan/ozone exhaust fan
troubIe
L4-34 LSU cooIing fan troubIe
L6-10 PoIygon motor Iock detection
Trouble content When separating the primary transfer belt unit,
change in the separation position sensor
characteristics is not detected within the specified
time.
Section PCU
Case 1 Cause Harness connection trouble between the PCU
PWB and the separation position sensor
Check and
remedy
Check the harness between the PCU PWB and
the separation position sensor.
Case 2 Cause The belt position sensor is not interrupted or it is
always interrupted. Belt separation clutch
operation trouble
Check and
remedy
Use SM6-3 to check the belt separation operation.
Case 3 Cause The primary transfer belt unit is not installed.
Check and
remedy
nstall the primary transfer belt.
Trouble content When the shift motor is initialized, no
characteristics change of the shifter home position
sensor is not detected within the specified time.
Section PCU
Case 1 Cause Shift motor trouble
Check and
remedy
Use SM6-1 to check the operation of the shift
motor.
Case 2 Cause Harness connection trouble between the PCU
PWB and the shift motor, control circuit trouble
Check and
remedy
Use SM30-1 to check the shifter home position
sensor. Check the harness and the connector
between the PCU PWB and the shift motor.
Case 3 Cause When the finisher is installed with the finisher
connector disconnected and when the finisher
communication trouble occurs.
Check and
remedy
Connect the finisher connector.
When the communication trouble occurs between
the PCU and the finisher, refer to the content of
F1-00.
Trouble content 1) The motor lock signal is detected during
rotation of the controller fan motor.
2) The motor lock signal is detected during
rotation of the HDD fan motor.
Section MFP
Case 1 Cause Fan motor trouble
Check and
remedy
Use SM6-2 to check the operation of the fan
motor.
Case 2 Cause Harness connection trouble between the mother
PWB and the fan motor.
Check and
remedy
Check the harness and the connector between the
mother PWB and the fan motor.
Case 3 Cause Control circuit trouble
Check and
remedy
Replace the controller PWB.
Case 4 Cause Mother PWB trouble.
Check and
remedy
Replace the mother PWB.
Trouble content When the paper exit cooling fan/toner hopper fan
are operated, the fan operation signal is not
detected within the specified time.
Section PCU
Case 1 Cause Fan connector disconnection
Check and
remedy
Check the harness and the connector between the
PCU PWB and the fan.
Case 2 Cause Fan does not rotate because of other trouble.
Check and
remedy
Use SM6-2 to check that the fan is rotation
actually.
Trouble content When the power cooling fan/ozone exhaust fan is
operated, the fan operation signal is not detected
within the specified time.
Section PCU
Case 1 Cause Power cooling fan or ozone exhaust fan connector
disconnection
Check and
remedy
Check the harness and the connector between the
PCU PWB and the fan.
Case 2 Cause Fan does not rotate because of other trouble
Check and
remedy
Use SM6-2 to check that the fan is actually
rotating.
Trouble content When the LSU cooling fan is operated, the fan
operation signal is not detected within the
specified time.
Section PCU
Case 1 Cause Fan connector disconnection
Check and
remedy
Check the harness and the connector between the
LSU PWB and the fan.
Case 2 Cause Fan does not rotate because of other trouble.
Check and
remedy
Use SM6-2 to check that the fan is rotation
actually. Replace the LSU fan. Replace the LSU
PWB.
Trouble content t is judged that the LSU polygon motor lock signal
is not outputted, and the lock signal is checked
after 7 sec from starting rotation of the polygon
motor and it is judged that the polygon motor does
not rotate properly.
Section LSU
Case 1 Cause Disconnection of the LSU connector or the LSU
inside harness, or breakage
Check and
remedy
Check connection of the harness and the
connector.
f the trouble cannot be removed, replace the
LSUcnt PWB or the LSU.
Case 2 Cause Polygon motor trouble, LSU PWB trouble
Check and
remedy
Use SM61-1 to check the operation of the polygon
motor.
f the trouble cannot be removed, replace the
LSUcnt PWB or the LSU.
MX3500N SELF DAG AND TROUBLE CODE 8 25
L8-01 No fuII wave signaI
L8-02 FuII wave signaI width abnormaIity
L8-20 Power controIIer communication
troubIe
PC--- PersonaI counter not instaIIed
U1-01 Battery troubIe
U2-00 EEPROM read/write error
(MFP detection)
U2-05 HDD/FIash/EEPROM data discrepancy
U2-10 SRAM user authentication index
check sum error
U2-11 EEPROM check sum error
(MFP detection)
U2-22 SRAM memory check sum error
Trouble content No full wave signal is detected.
Section PCU
Case 1 Cause Harness trouble
Check and
remedy
Check connection of the harness and the
connector.
Case 2 Cause Power unit trouble
Check and
remedy
Replace the power unit.
Case 3 Cause PCU PWB trouble
Check and
remedy
Replace the PCU PWB.
Trouble content The full wave signal is judged as frequency
abnormality. (The detection frequency is judged as
65Hz or above or 45Hz or less.)
Section PCU
Case 1 Cause Harness trouble
Check and
remedy
Check the harness and the connector connection.
Case 2 Cause Power unit trouble
Check and
remedy
Replace the power unit.
Case 3 Cause PCU PWB trouble
Check and
remedy
Replace the PCU PWB.
Trouble content Communication establishment error/Framing/
Parity/Protocol error
Section MFP
Case 1 Cause Connector connection trouble between the mother
board PWB and the MFPcnt PWB.
MFPcnt PWB mother board connector pin
breakage
Check and
remedy
Check the connector connection between the
mother board PWB and the MFPcnt PWB. Check
grounding of the machine.
Case 2 Cause Mother PWB trouble
Check and
remedy
Replace the mother PWB.
Case 3 Cause Mother PWB jumper error
Check and
remedy
Set the mother PWB jumper to the Default side.
Trouble content The personal counter is not installed.
Section MFP
Case 1 Cause The personal counter is not installed.
Check and
remedy
nstall the personal counter.
Trouble content Backup SRAM battery voltage fall
Section MFP
Case 1 Cause 1) Battery life
2) Battery circuit abnormality
Check and
remedy
Check that the battery voltage is about 2.5V or
above.
Trouble content EEPROM device read/write error
Section MFP
Case 1 Cause EEPROM device trouble
Check and
remedy
Replace the EEPROM device.
Case 2 Cause EEPROM device contact failure
Check and
remedy
Check that EEPROM device is properly inserted.
Case 3 Cause Device access error due to electrical noises
Check and
remedy
Replace the MFPcnt PWB.
Trouble content A HDD or Flash memory for user authentication
different from that used before turn off the power is
installed.
Section MFP
Case 1 Cause HDD replacement or Flash memory replacement
Check and
remedy
nitialize the authentication information with
SM16, and import the backup data (exported
data) if any.
Trouble content User index information (basic data of user
authentication) check sum error on the SRAM
Section MFP
Case 1 Cause 1) SRAM trouble
2) Hang-up of the control circuit due to electrical
noises
3) MFPcnt PWB SRAM access circuit trouble
Check and
remedy
Use SM16 to cancel U2 trouble.
Trouble content Counter information check sum error on the
EEPROM
Section MFP
Case 1 Cause 1) EEPROM device trouble
2) EEPROM device contact failure
3) Device access error due to electrical noises
Check and
remedy
Use SM16 to cancel U2 trouble.
Trouble content MFPcnt PWB SRAM memory check sum error
Section MFP
Case 1 Cause SRAM trouble
Check and
remedy
1) nitialize the communication management
table registered in SRAM and the FAX soft
switch.
2) Since the registered contents have been
deleted, register them again.
Case 2 Cause Control circuit hang-up due to electrical noises
Check and
remedy
Use SM16 to cancel U2 trouble.
Case 3 Cause MFPcnt PWB SRAM access circuit trouble
Check and
remedy
Replace the MFPcnt PWB.
MX3500N SELF DAG AND TROUBLE CODE 8 26
U2-23 MFPC section SRAM memory
individuaI data check sum error
U2-24 SRAM memory user authentication
counter check sum error
U2-25 FIash memory user authentication
counter check sum error
U2-30 SeriaI number data discrepancy
(MFP PCU)
U2-50 HDD section individuaI data check
sum error
U2-80 EEPROM read/write error
(SCU detection)
U2-81 Adjustment vaIue check sum error
(SCU detection)
Trouble content MFPcnt PWB SRAM memory individual data
check sum error (Communication management
table, sender registration data, etc.)
Section MFP
Case 1 Cause SRAM trouble
Check and
remedy
1) Turn OFF/ON the power to initialize the data
related to the check sum error automatically.
2) Since the registered contents have been
deleted, register them again.
Case 2 Cause Control circuit hang-up due to electrical noises
Check and
remedy
Use SM16 to cancel U2 trouble.
Case 3 Cause MFPcnt PWB SRAM access circuit trouble
Check and
remedy
Replace the MFPcnt PWB.
Trouble content Check sum error of the user counter on SRAM
Section MFP
Case 1 Cause 1) SRAM trouble
2) Control circuit hang-up due to electrical
noises
3) MFPcnt PWB SRAM access circuit trouble
Check and
remedy
Use SM16 to cancel U2 trouble.
Trouble content Check sum error of the user authentication
counter on FLASH
Section MFP
Case 1 Cause Flash trouble. Control circuit hang-up due to
electrical noises
MFPcnt PWB FLASH access circuit trouble.
Check and
remedy
Use SM16 to recalculate the check sum of the
user counter and save the normal sum value.
Trouble content The serial number stored in the PCU differs from
that stored in the MFP.
Section MFP
Case 1 Cause EEPROM is not changed when the PCU/MFPcnt
PWB is replaced.
Check and
remedy
1) Check that EEPROM is properly set.
2) Check that EEPROM on the previous PWB is
inserted to the newly installed PWB.
Trouble content MFPcnt HDD individual data check sum error
(One-touch, group, program, etc.)
Section MFP
Case 1 Cause Write/read error to/from HDD
Check and
remedy
1) Turn OFF/ON the power to initialize the data
related to the check sum error contents.
2) Since the registered contents have been
deleted, register them again.
3) f the trouble is not canceled, replace the
HDD.
Case 2 Cause Control circuit hang-up due to electrical noises
Check and
remedy
Use SM16 to cancel U2 trouble.
Case 3 Cause MFPcnt PWB HDD access circuit trouble
Check and
remedy
Replace the MFPcnt PWB.
Trouble content 1) EEPROM version error
2) Write error to EEPROM
Section Scanner
Case 1 Cause EEPROM trouble, installation of EEPROM which
is not initialized
Check and
remedy
Check that EEPROM is properly set.
Case 2 Cause SCU PWB EEPROM access circuit trouble
Check and
remedy
To avoid deletion of the counter data/adjustment
data, use the simulation to save the counter/
adjustment values. (f there is a printer option,
execute SM22-1 to save the counter data and the
adjustment values.) Replace the SCU PWB. Use
SM16 to cancel the trouble.
Trouble content EEPROM (SCU) check sum error
Section Scanner
Case 1 Cause Control circuit hang-up due to electrical noises
Check and
remedy
Use SM16 to cancel U2 trouble.
Case 2 Cause EEPROM trouble
Check and
remedy
To avoid deletion of the counter data/adjustment
data, use the simulation to save the counter/
adjustment values. (f there is a printer option,
execute SM22-1 to save the counter data and the
adjustment values.) Replace the SCU PWB. Use
SM16 to cancel the trouble.
Case 3 Cause SCU PWB EEPROM access circuit trouble
Check and
remedy
Check that EEPROM is properly set.
MX3500N SELF DAG AND TROUBLE CODE 8 27
U2-90 EEPROM read/write error
(PCU detection)
U2-91 EEPROM (PCU) check sum error
U5-00 SPF communication troubIe
U5-16 SPF fan motor troubIe
U5-30 SPF Iift-up troubIe
U5-31 SPF tray Iift-down troubIe
U5-40 SPF instaII troubIe
U6-00 Desk communication troubIe
U6-01 Tray 1 Iift-up troubIe
U6-02 Tray 2 Iift-up troubIe
Trouble content EEPROM version error, write error to EEPROM
Section PCU
Case 1 Cause EEPROM trouble, installation of EEPROM which
is not initialized
Check and
remedy
Check that EEPROM is properly set.
Case 2 Cause PCU PWB EEPROM access circuit trouble
Check and
remedy
To avoid deletion of the counter data/adjustment
data, use the simulation to save the counter/
adjustment values. (f there is a printer option,
execute SM22-1 to save the counter data and the
adjustment values.) Replace the PCU PWB. Use
SM16 to cancel the trouble.
Trouble content Check sum error of adjustment value (PCU)
Section PCU
Case 1 Cause Control circuit hang-up due to electrical noises
Check and
remedy
Use SM16 to cancel the trouble.
Case 2 Cause EEPROM trouble.
Check and
remedy
Check that EEPROM is properly set.
Case 3 Cause PCU PWB EEPROM access circuit trouble
Check and
remedy
To avoid deletion of the counter data/adjustment
data, use the simulation to save the counter/
adjustment values. (f there is a printer option,
execute SM22-1 to save the counter data and the
adjustment values.) Replace the PCU PWB.
Trouble content Communication error between the SCU and the
DSPF, communication line test error after turning
on the power or canceling the exclusive simulation
(MX-3501N/3501FN/4501N/4501FN)
Section Scanner
Case 1 Cause Malfunction due to electrical noises
Check and
remedy
Cancel the trouble by turning OFF/ON.
Case 2 Cause Connector and harness connection trouble or
disconnection
Check and
remedy
Check the connector and the harness of the
communication line.
Case 3 Cause Control (SCU) PWB trouble. DSPF PWB trouble
Check and
remedy
Replace the control (SCU) PWB. Replace the
DSPF PWB.
Trouble content The motor lock signal is detected during rotation of
the fan.
Section Scanner
Case 1 Cause Fan motor trouble,harness of the fan motor related,
circuit trouble
Check and
remedy
Use SM2-3 to check the operation.
Check harness, connector and fan motor related
circuit.
Trouble content Lift-up trouble is detected 5 times continuously.
(MX-3501N/4501N)
Section Scanner
Case 1 Cause STUD/STLD trouble
Check and
remedy
Check STUD/STLD and its harness and connector.
Check the lift-up unit.
Trouble content Lift-down trouble (STLD does not turn OFF within
the specified time.) (MX-3501N/4501N)
Section Scanner
Case 1 Cause STUD/STLD trouble
Check and
remedy
Check STUD/STLD and its harness and connector.
Check the lift-up unit.
Trouble content Detected the installed (individual installed signal )
of RSPF/DSPF both.
Section Scanner
Case 1 Cause Circuit trouble of the installed detection signal
Check and
remedy
Check installed detection circuit and harness,
connector.
Trouble content Desk communication error, communication line
test error after turning on the power or canceling
the exclusive simulation
Section PCU
Case 1 Cause Connector and harness connection trouble or
disconnection, desk control PWB trouble, control
PWB (PCU) trouble, malfunction due to electrical
noises
Check and
remedy
Cancel the trouble by turning OFF/ON. Check the
connector and the harness of the communication
line.
Trouble content DLUD1 does not turn ON within the specified time.
Section PCU
Case 1 Cause DLUD1 sensor trouble, tray 1 lift-up motor trouble,
desk PWB, lift-up unit, paper feed unit harness
connection trouble
Check and
remedy
Check DLUD1 and its harness and connector.
Check the lift-up unit.
Trouble content DLUD2 does not turn ON within the specified time.
Section PCU
Case 1 Cause DLUD2 sensor trouble, tray 2 lift-up motor trouble,
desk PWB, lift-up unit, paper feed unit harness
connection trouble
Check and
remedy
Check DLUD2 and its harness and connector.
Check the lift-up unit.
MX3500N SELF DAG AND TROUBLE CODE 8 28
U6-09 LCC Iift motor troubIe
U6-10 Desk transport motor troubIe
U6-20 LCC communication troubIe
U6-21 LCC transport motor troubIe
U6-22 LCC 24V power abnormaIity
U6-50 Desk incompatibiIity troubIe
U6-51 LCC incompatibiIity troubIe
UC-02 CPT-ASIC abnormaIity
UC-20 Document controI moduIe troubIe
Trouble content The encoder input value is not changed in
0.13sec (1st time)/0.5sec (2nd time and later)
after rotation of the motor.
The motor is rotated for 18sec or more.
The encoder is changed after passing a certain
time from stopping the motor. (2sec, 10 count or
more)
Section PCU
Case 1 Cause Sensor trouble, LCC control PWB trouble, gear
breakage, lift motor trouble
Check and
remedy
Use SM4-2 and 4-3 to check the operation of the
sensor and the lift motor. Use SM15 to cancel the
trouble.
Trouble content Desk transport motor operation trouble
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, overcurent to
the motor, console finisher control PWB trouble
Check and
remedy
Use SM 4-3 to check the operation of the desk
transport motor.
Trouble content LCC communication error. Communication line
test error after turning ON the power or canceling
the exclusive simulation. LCC and machine model
codes discrepancy error
Section PCU
Case 1 Cause Connector and harness connection trouble or
disconnection, LCC control PWB trouble, control
PWB (PCU) trouble, malfunction due to electrical
noises
Check and
remedy
Turn OFF/ON the power to cancel the trouble.
Check the connector and the harness of the
communication line.
Trouble content The encoder input value is not changed in
0.06sec after turning on the motor.
The encoder input value is changed after a
certain time from turning OFF the motor. (After
5sec, count is made for 0.1sec to get 100 or
more count.)
Section PCU
Case 1 Cause Motor lock, motor RPM abnormality, an
overcurrent to the motor, LCC control PWB trouble
Check and
remedy
Use SM4-3 to check the operation of the transport
motor.
Trouble content DC24V power is not supplied to LCC.
Section PCU
Case 1 Cause Connector and harness connection trouble or
disconnection, LCC control PWB trouble, power
unit trouble
Check and
remedy
Check the connector and the harness of the power
line. Check that the power unit and the LCC control
PWB is of 24V.
Trouble content Detection of desk connection incompatible with the
MX-3500/4500/3501/4501 **
Section PCU
Case 1 Cause Connection of a desk which is incompatible with
the MX-3500/4500/3501/4501** is detected.
Check and
remedy
Connect the MX-DEX3/DEX4.
Trouble content Detection of LCC connection which is incompatible
with the MX-3500/4500/3501/4501 **.
Section PCU
Case 1 Cause Connection of the LCC, which is incompatible with
the MX-3500/4500/3501/4501 ** is detected.
Check and
remedy
Connect the MX-LCX1.
Trouble content CPT-ASC access error (When the ASC does not
operate normally.)
Section Scanner
Case 1 Cause CPT-ASC abnormality, SCU PWB abnormality
Check and
remedy
Turn OFF/ON the power several times. f the
trouble still occurs, replace the SCU PWB or the
CPT-ASC.
Trouble content Communication error between SCU and DOCC
Communication line test error when turning on the
power or after canceling an exclusion simulation.
Section Scanner
Case 1 Cause Connector or harness connection error or
disconnection
Check and
remedy
Check the connector and harness in the
communication line.
Case 2 Cause Control PWB (SCU) trouble, DOCC PWB trouble.
Check and
remedy
Replace the SCU PWB or the DOCC PWB.
Case 3 Cause Malfunction due to electrical noises.
Check and
remedy
Turn OFF/ON the power to electrical cancel the
trouble.