DC201E Series

ADVANCED MOTION CONTROLS

3805 Calle Tecate, Camarillo, CA 93012
Tel: (805) 389-1935, Fax: (805) 389-1165
Page 1 of 11
DIGIFLEX DIGITAL SERVO DRIVES
WITH CANopen INTERFACE
MODEL: DC201E20A8BDC

FEATURES:

Fully digital, state-of-the-art DSP design
Brushed DC, brushless AC drive technology
10 kHz digital current loop, 5 kHz digital velocity loop, 5 kHz digital
position loop with programmable gain settings
Encoder and Hall sensor feedback for sinusoidal commutation
Surface-mount technology
Small size, low cost, ease of use

Isolated CAN bus interface for setup and networking
Supports CANopen communication protocol (DS301) and Device Profile
for Drives and Motion Control commands (DSP-402)
CAN bus address and bit rate selection via DIP-switches
Windows based DigiFlex DriveWare setup software via CAN interface
(operates with third party PC-to-CAN interface)
Operates in torque, velocity or position mode

Single encoder input
3 programmable isolated digital inputs (sinking), sourcing inputs optional (-
SRC).
3 programmable isolated digital outputs (sinking)
Dedicated isolated limit and home switch inputs
2 programmable analog inputs (14-bit)
1 programmable analog output (10-bit)

Four quadrant regenerative operation
Separate backup logic supply input
Bi-color LED status indicator
Extensive built-in protection against:
over-voltage
under-voltage
short-circuit: phase-phase, phase-ground
over-current
over-temperature


Note: picture for reference only.
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:
ADVANCED MOTION CONTROLS DC201E Series
Page 2 of 11
BLOCK DIAGRAM:
10K
10K
10K
+5V +5V +5V
DRIVE READY
PROGR. OUTPUT 1..3
GNDIO
GNDIO
GNDIO
GNDIO
GNDIO
DRIVE ENABLE
+PROGR. ANALOG INPUT 1,2
-PROGR. ANALOG INPUT 1,2
PROGR. ANALOG OUTPUT
HALL A
HALL B
HALL C
GND
MOT ENC A+
MOT ENC A-
MOT ENC B+
MOT ENC B-
MOT ENC I+
MOT ENC I-
I
/
O

I
S
O
L
A
T
I
O
N
CAN INTERFACE
M
O
T
O
R

F
E
E
D
B
A
C
K
MAIN CONTROLLER
CURRENT CONTROL
TORQUE CONTROL
VELOCITY CONTROL
POSITION CONTROL
+
-
+5V
5.6VZ
CONTROL
LOGIC AND
PROTECTION
CIRCUIT
SYSTEM RESET
GNDSGN
CAN_H
CAN_L
GNDCAN
SHIELD_CAN
RTERM_CAN
CAN_V+
FAULT RESET, HOME,
POS LIMIT, NEG LIMIT
PROGR. INPUT 1..3
DC201E15A8BDC
ISOLATION
MOTOR A
MOTOR B
MOTOR C
LOGIC POWER
SUPPLY
HIGH VOLTAGE
LOGIC POWER
GROUND
POWER
OUTPUT STAGE


DESCRIPTION:

The DC201E Series digital PWM servo drives are designed to drive brushed and brushless servomotors. These fully
digital drives can operate in torque, velocity, or position mode. Various feedback signals can be used to close the
velocity and position loop. The command source can be generated internally or can be supplied externally. In addition
to motor control, these dri ves feature dedicated and programmable digital and analog inputs and outputs to enhance
interfacing with external controllers and devices.

DC201E Series drives feature a single CAN interface which supports the CANopen protocol (DS301 and DSP402).
This interface is used for drive configuration and setup as well as online operation in networked applications. Drive
commissioning can be accomplished through DigiFlex DriveWare, a fully graphical Windows based application.

Torque, velocity, or position commands can be generated from an analog input, a preset index table, or the CAN
interface. The DC201E Series also feature an interpolated position mode with cubic interpolation for smooth,
coordinated, multi-axis position control via the CAN interface. A homing routine based on the home switch input and/or
the encoder index pulse is also implemented.

All drive and motor parameters are stored in non-volatile memory.
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:
ADVANCED MOTION CONTROLS DC201E Series
Page 3 of 11
SPECIFICATIONS:

POWER STAGE SPECIFICATIONS DC201E20A8BDC
DC SUPPLY VOLTAGE 2080 VDC
PEAK CURRENT 20A (14.2Arms)
MAXIMUM CONTINUOUS CURRENT 10A (7.1Arms)
MINIMUM LOAD INDUCTANCE 250 H
SWITCHING FREQUENCY 20 kHz
HEATSINK (BASEPLATE) TEMPERATURE RANGE 0 to 65 C, disables at 65 C
POWER DISSIPATION AT CONTINUOUS CURRENT 50W
MIN. UNDER-VOLTAGE SHUTDOWN 20 VDC
MAX. OVER-VOLTAGE SHUTDOWN 86 VDC
LOGIC SUPPLY VOLTAGE (backup supply) 2080 VDC, 20W maximum


CAN INTERFACE SUPPLY SPECIFICATIONS
DC SUPPLY VOLTAGE 7.5 to 13 VDC
INPUT CURRENT 150 mA max.


MECHANICAL SPECIFICATIONS
POWER CONNECTOR: P1 Plug-in with crimp-terminal
MOTOR FEEDBACK CONNECTOR: CN3* 15-pin high density female D-sub
I/O CONNECTOR: CN2* 26-pin high density female D-sub
COMMUNICATIONS INTERFACE (CAN): CN1* 9-pin male D-sub
SIZE
5.22 x 3.52 x 1.42 inches
132.5 x 89.5 x 35.9 mm
WEIGHT
1 lb.
0.44 kg

* Mating connectors are not included.
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:
ADVANCED MOTION CONTROLS DC201E Series
Page 4 of 11
PIN FUNCTIONS:

P1 - Motor and Power Connector:

CAUTION: the pin numbering of the mating connector is different from the numbering of the drive connector.
In the table below, the second column corresponds to the drive pin numbering (silkscreen). The second to last
column corresponds to the mating connector pin numbering.

DRIVE
CONN.
PIN NAME DESCRIPTION I/O PIN
MATING
CONN.
1 MA Motor phase A O 6
2 MB Motor phase B O 5
3 MC Motor phase C O 4
4 HV IN
DC motor and power input. This input is used
to supply power to the motor and drive logic
circuitry.
I 3
5 GND Ground GND 2
P1
6
LOGIC
PWR
Logic supply input. This input can be used to
supply power to the drive logic circuitry only.
Effective only when the voltage applied to pin
P1-4 is lower then the voltage applied to P1-6.
I 1


CN3 - Motor Feedback Connector:

CONNECTOR PIN NAME DESCRIPTION I/O
1 MOT ENC A+ I
2 MOT ENC A-
Differential Encoder Input
I
3 MOT ENC B+ I
4 MOT ENC B-
Differential Encoder Input
I
5 GNDSGN Signal ground GNDSGN
6 Hall A I
7 Hall B I
8 Hall C
Commutation sensor inputs. Internal
2K pull-up to +5VDC.
I
9 - Not connected
10 - Not connected
11 MOT ENC I+ I
12 MOT ENC I-
Differential Encoder Input
I
13 +5V OUT
+5V @ 400mA max. Short-circuit
protected.
O
14 MOTOR OVER TEMP TTL input I
CN3
15 SHIELD
Motor feedback cable shield. Internally
connected to GNDSGN
SHLD

CN2 I/O Connector:

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:
ADVANCED MOTION CONTROLS DC201E Series
Page 5 of 11 GNDIO
OUTPUT
CONNECTOR PIN NAME DESCRIPTION I/O
1 +24V IN
+24V input pull-up (for sourcing
inputs option only)
I
2 PROG INPUT 1 I
3 PROG INPUT 3
Programmable digital input. Opto-
isolated. See schematic below.
I
4 FAULT RESET
Fault reset input. Opto-isolated.
See schematic below.
I
5 PROG OUTPUT 2
Programmable digital output. Opto-
isolated. See schematic below.
O
6 - Reserved
7 -PROG ANALOG INPUT 1 I
8 -PROG ANALOG INPUT 2
See pin 16, 17
I
9 GNDSGN Signal ground. GNDSGN
10 +24V IN
+24V input pull-up (for sourcing
inputs option only)
I
11 HOME SWITCH
Home switch input. Opto-isolated.
See schematic below.
I
12 PROG INPUT 2
Programmable digital input. Opto-
isolated. See schematic below.
I
13 DRIVE ENABLE
Drive enable input. Opto-isolated.
See schematic below.
I
14 PROG OUTPUT 1 O
15 PROG OUTPUT 3
Programmable digital output. Opto-
isolated. See schematic below.
O
16 +PROG ANALOG INPUT 1 I
17 +PROG ANALOG INPUT 2
Programmable analog input. Opto-
isolated. See schematic below.
I
18 SYSTEM RESET
TTL input. Pull to ground to reset
drive (same as power cycle).
Referenced to GNDSGN.
I
19 NEGATIVE LIMIT SWITCH
Negative limit switch input. Opto-
isolated. See schematic below.
I
20 POSITIVE LIMIT SWITCH
Positive limit switch input. Opto-
isolated. See schematic below.
I
21 DRIVE READY
Drive ready output. Opto-isolated.
See schematic below.
O
22 GNDIO Isolated ground GNDIO
23 GNDIO Isolated ground GNDIO
24 GNDA
Analog signal ground. Internally
connected to GNDSGN
GNDA
25 PROG ANALOG OUTPUT 1
Programmable analog output. See
schematic below.
O
CN2
26 SHIELD
Cable shield. Internally connected
to GNDSGN
SHLD

I/O SCHEMATICS:

Isolated Outputs

DRIVE READY, PROGRAMMABLE OUTPUT 13
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:
ADVANCED MOTION CONTROLS DC201E Series
Page 6 of 11
GNDIO
INPUT
10K
INPUT
+24V IN
10K

Active maximum voltage +0.7 VDC
Active maximum current 200 mA
Inactive maximum voltage +30 VDC
Inactive maximum current 0.01 mA

Isolated Inputs

DRIVE ENABLE, FAULT RESET, HOME SWITCH, POSITIVE LIMIT SWITCH, NEGATIVE LIMIT SWITCH,
PROGRAMMABLE INPUT 13

Sinking Inputs (standard version)

Active maximum voltage +30 VDC
Active mi nimum voltage +18 VDC
Inactive maximum voltage +2.5 VDC
Inactive minimum voltage 5VDC

Sourcing Inputs (optional SRC version)


Active maximum voltage +10VDC
Active minimum voltage 5VDC
Inactive maximum voltage +24VIN + 5VDC
Inactive minimum voltage +24VIN 2.5VDC

Programmable Analog Output

Voltage Range -10V+10V
Resolution 10-bit
Minimum Load Resistance 2K Ohm

Programmable Analog Inputs

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:
ADVANCED MOTION CONTROLS DC201E Series
Page 7 of 11
+
-
10K 10K
10K
10K 10K
0.01uF
0.01uF


Voltage Range 10V+10V
Resolution 12-bit

System Reset Input

CN1 - Communications Interface (CAN):

CONNECTOR PIN NAME DESCRIPTION I/O
2 CAN_L CAN _L bus line (dominant low) I
3 CAN_GND CAN ground GND
5 CAN_SHLD CAN shield SHLD
7 CAN_H CAN_H bus line (dominant high) I
8 CAN_TERM
Termination. Connect to CAN_H
for CAN bus termination (120
Ohm)
GND
CN1
9 CAN_V+
CAN external supply
7.513 VDC
I

DIP SWITCH FUNCTIONS:

CAN Address Setting

Node-ID SW1 SW2 SW3 SW4 SW5 SW6
Via CAN OFF OFF OFF OFF OFF OFF
1 ON OFF OFF OFF OFF OFF
2 OFF ON OFF OFF OFF OFF
3 ON ON OFF OFF OFF OFF

63 ON ON ON ON ON ON
+5V
5.6VZ
14K
1K
0.1uF
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:
ADVANCED MOTION CONTROLS DC201E Series
Page 8 of 11

CAN Bus Bit Rate Setting

Bit Rate (bits/sec) SW7 SW8
Via CAN OFF OFF
500K OFF ON
250K ON OFF
125K ON ON

CAN Bus Termination

SW10 can be used for CAN bus termination. Setting SW10 ON will internally connect the CAN_H signal to CAN_L via
a 120 resistor. This can be used if the drive is the last node in a CAN network. Setting SW10 OFF will open this
termination. Note: the CAN_TERM pin can also be used for termination, see below.


DIGIFLEX DRIVEWARE:

DigiFlex DriveWare is a Windows based application that can be used to setup and configure the DigiFlex series of
digital servo drives via the CAN interface. This application operates with the following PC-to-CAN interfaces:

Manufacturer Part Number Style Manufacturer Contact Information
Advantech PCL-841 ISA-bus www.advantech.com
IXXAT any any www.ixxat.com
Kvaser any any www.kvaser.com
Vector Any Any www.vector-cantech.com
ESD Electronics any any www.esd-electronics.com

CANopen OBJECT DICTIONARY:

For more detailed information on CANopen, please visit http://www.can-cia.org/, the official web site of CAN in
Automation (CiA), the governing body of the CANopen standard.

I. Communication Profile Objects (DS301):

1000h: Device_Type
1001h: Error_register
1002h: Manufacturer_Stat us_Register
1008h: Manufacturer_Device_Name
1009h: Manufacturer_Hardware_Version
100Ah: Manufacturer_Software_Version
100Ch: guard-time
100Dh: life-time factor
1010h: store_parameters
1400h: 1
st
receive pdo communication parameter
1401h: 2
nd
receive pdo communication parameter
1402h: 3
rd
receive pdo communication parameter
CAN
TRANSCEIVER
CAN_H
CAN_L
CAN_GND
SW10
120
CAN_TERM
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:
ADVANCED MOTION CONTROLS DC201E Series
Page 9 of 11
1403h: 4
th
receive pdo communication parameter
1404h: 5
th
receive pdo communication parameter
1414h: 21
st
receive pdo communication parameter
1415h: 22
nd
receive pdo communication paramet er
1416h: 23
rd
receive pdo communication parameter
1417h: 24
th
receive pdo communication parameter
1600h: 1
st
receive pdo mapping parameter
1601h: 2
nd
receive pdo mapping parameter
1602h: 3
rd
receive pdo mapping parameter
1603h: 4
th
receive pdo mapping parameter
1604h: 5
th
receive pdo mapping parameter
1614h: 21
st
receive pdo mapping parameter
1615h: 22
nd
receive pdo mapping parameter
1616h: 23
rd
receive pdo mapping parameter
1617h: 24
th
receive pdo mapping parameter
1800h: 1
st
transmit pdo communication parameter
1802h: 3
rd
transmit pdo communication parameter
1803h: 4
th
transmit pdo communication parameter
1804h: 5
th
transmit pdo communication parameter
1814h: 21
st
transmit pdo communication parameter
1815h: 22
nd
transmit pdo communication parameter
1816h: 23
rd
transmit pdo communication parameter
1817h: 24
th
transmit pdo communication parameter
1818h: 25
th
transmit pdo communication parameter
1819h: 26
th
transmit pdo communication parameter
1A00h: 1
st
transmit pdo mapping parameter
1A02h: 3
rd
transmit pdo mapping parameter
1A03h: 4
th
transmit pdo mapping parameter
1A04h: 5
th
transmit pdo mapping parameter
1A14h: 21
st
transmit pdo mapping parameter
1A15h: 22
nd
transmit pdo mapping parameter
1A16h: 23
rd
transmit pdo mapping parameter
1A17h: 24
th
transmit pdo mapping parameter
1A18h: 25
th
transmit pdo mapping parameter
1A19h: 26
th
transmit pdo mapping parameter

II. Drive Profile Objects (DSP402)

Common Objects

6402h: motor_type
6403h: motor_catalogue_number
6404h: motor_manufacturer
6410h: motor_data
6510h: drive_data
6502h: supported_ drive_modes
6503h: drive_catalogue_number
6504h: drive_manufacturer

2001h: user_defined_drive_name
2002h: user_units
200Eh: active_non_fatal_errors
200Fh: error_self_reset
2011h: commutation_sensor_selection_code
2012h: hall_sensor_parameters
201Fh: hall_sensor_error_option_code
2031h: hall_sensor_error_counter
2032h: hall_sensor_error_counter_limit
2013h: encoder_parameters
2020h: encoder_counter
2021h: encoder_position
2022h: encoder_index_counter
2027h: encoder_error_option_code
2023h: encoder_error_counter
2024h: encoder_error_counter_limit
2014h: auxiliary_encoder_parameters
2028h: auxiliary_encoder_counter
2029h: auxiliary_encoder_position
202Ah: auxiliary_encoder_index_counter
2030h: auxiliary_encoder_error_option_code
202Bh: auxiliary_encoder_error_counter
202Ch: auxiliary_encoder_error_counter_limit
2040h: DIP-switch_settings
20A0h: programmable_digital_inputs
20A1h: programmable_digital_outputs
20A2h : programmable_analog_inputs
20A3h: programmable_analog_outputs
20A4h: programmable_digital_inputs_polarity
20A5h: programmable_digital_inputs_function
20A8h: programmable_digital_outputs_polarity
20A9h: programmable_digital_outputs_function
20ACh : programmable_analog_input_parameters
20AEh: programmable_analog_output_parameters
20C2h: power_stage_temperature
20C8h: communication_control
208Fh: load_inertia

Device Control Objects

6040h: controlword
20C4h: controlword_initial_value
20C5h: auxiliary_controlword
6041h: statusword
605Ah: quick_stop_option_code
605Bh: shutdown_option_code
605Ch: disable_operation_option_code
6060h: modes_of_operation
6061h: modes_of_operation display
2000h: statusword_1
2004h: dedicated_digital_inputs
2005h: dedicated_digital_outputs
2006h: dedicated_digital_inputs_polarity
2007h: dedicated_digital_outputs_polarity
2049h: invert_command
20B0h: trigger_at_value
20B1h: capture_value
20B3h: trigger_signal
20B5h: capture_signal
20B6h: capture_event
20C1h: delay_times
20C3h: motor_overtemperature_option_code

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:
ADVANCED MOTION CONTROLS DC201E Series
Page 10 of 11
Factor Group Objects

6090h: velocity_encoder_resolution
608Fh: position_encoder_resolution
6093h: position_factor
6094h: velocity_encoder_factor
6097h: acceleration_factor
2079h: analog_torque_command_factor
207Ah: digital_torque_command_factor
2081h: analog_velocity_command_factor
2082h: digital _velocity_command_factor
2091h: analog_position_command_factor
2092h: digital_position_command_factor

Profile Position Mode Objects

607Ah: target_position
607Dh: software_position_limit
6086h: motion_profile_type
607Fh: maximum_profile_velocity
6081h: profile_velocity
6083h: profile_acceleration
6084h: profile_deceleration
6085h: Quick_stop_deceleration

Homing Mode Objects

607Ch: home_offset
6098h: homing_method
6099h: homing_speeds
609Ah: homing_acceleration

Position Control Function Objects

6062h: position_demand_value
6063h: position_actual_value*
6064h: position_actual_value
6067h: position_window
6068h: position_window_time
6065h: following_error_window
6066h: following_error_time_out
60F4h: following_error_actual_value
60FBh: position_control_parameter_set
60FCh: position_demand_value*
2090h: demand_position_offset
2093h: position_command_low_pass_filter

Profile Velocity Mode Objects

6069h: velocity_sensor_actual_value
606Ah: sensor_selection_code
606Bh: velocity_demand_value
606Ch: velocity_actual_value
606Dh: velocity_window
606Eh: velocity_window_time
606Fh: velocity_threshold
6070h: velocity_threshold_time
60F9h: velocity_control_parameter_set
60FFh: target_velocity
2080h: demand_velocity_offset
2083h: velocity_command_low_pass_filter
2084h: velocity_error

Profile Torque Mode Objects

6071h: target_torque
6072h: max_torque
6074h: torque_demand_value
6075h: motor_rated_current
6076h: motor_rated_torque
6077h: torque_actual_value
6078h: current_actual_value
6079h: dc_link_circuit_voltage
6087h: torque_slope
6088h: torque_profile_type
60F8h: torque_control_parameters
2010h: rated_voltage
2070h: current_control_parameter_set
2074h: target_current_q
2075h: reference_current_q
2077h: reference_torque
2078h: rated_torque_constant
207Bh: Torque command low pass filter



ORDERING INFORMATION:

Standard model: DC201E20A8BDCX
With sourcing inputs: DC201E20A8BDCX-SRC
X indicates the current revision letter.
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:
ADVANCED MOTION CONTROLS DC201E Series
Page 11 of 11
MOUNTING DIMENSIONS:


ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By: