Analog Servo Drive: Description Power Range

Analog Servo Drive AZ20A20
Description Power Range

Peak Current 20 A
Continuous Current 10 A
Supply Voltage 40 - 175 VDC
The AZ20A20 PWM servo drive is designed to drive
brush-type DC motors at a high switching frequency.
To increase system reliability and to reduce cabling
costs, the drive is designed for direct integration into
your PCB. The AZ20A20 is fully protected against over-
voltage, under-voltage, over-current, over-heating and
short-circuits. A single digital output indicates
operating status. The drive interfaces with digital
controllers that have analog +/-10V output. This servo
drive requires only a single unregulated isolated DC
power supply, and is fully RoHS (Reduction of
Hazardous Substances) compliant.
See Part Numbering Information on last page of
datasheet for additional ordering options.

Features

High Power Density
Compact Size
Direct Board-to-Board Integration
Lightweight
High Switching Frequency
Four Quadrant Regenerative Operation
Wide Temperature Range
High Performance Thermal Dissipation
Differential Input Command
Current Monitor Output
Digital Fault Output Monitor
Wide Supply Voltage Range

HARDWARE PROTECTION
Over-Voltage
Under-Voltage
Over-Current
Over-Temperature
Short-circuit (phase-phase)
Short-circuit (phase-ground)
INPUTS/OUTPUTS
Digital Fault Output
Digital Inhibit Input
Analog Current Monitor
Analog Command Input
Analog Current Reference
MODES OF OPERATION
Current
MOTORS SUPPORTED
Single Phase (Brushed, Voice Coil, Inductive Load)
COMMAND SOURCE
10 V Analog
COMPLIANCES & AGENCY APPROVALS
RoHS

Release Date:
10/8/2010
Revision:
2.01
ADVANCED Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 1 of 7

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:


BLOCK DIAGRAM

Information on Approvals and Compliances

RoHS (Reduction of Hazardous Substances) is intended to prevent hazardous substances such as lead from being
manufactured in electrical and electronic equipment.
Release Date:
10/8/2010
Revision:
2.01
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 2 of 7

ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:


Release Date:
10/8/2010
Revision:
2.01
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 3 of 7

SPECIFICATIONS
Power Specifications
Description Units Value
DC Supply Voltage Range VDC 40 175
DC Bus Under Voltage Limit VDC 36
DC Bus Over Voltage Limit VDC 193
Maximum Peak Output Current
1
A 20
Maximum Continuous Output Current A 10
Maximum Continuous Output Power W 1663
Maximum Power Dissipation at Continuous Current W 88
Minimum Load Inductance (Line-To-Line)
2
H 250
Internal Bus Capacitance
3
F 20
Low Voltage Supply Outputs - +6 VDC (30 mA)
Switching Frequency kHz 20.7
Control Specifications
Command Sources - 10 V Analog
Modes of Operation - Current
Motors Supported - Single Phase (Brushed, Voice Coil, Inductive Load)
Hardware Protection -
Over Current, Over Temperature, Over Voltage, Under Voltage, Short Circuit
(Phase-Phase & Phase-Ground)
Mechanical Specifications
Agency Approvals - RoHS
Size (H x W x D) mm (in) 76.2 x 50.8 x 22.86 (3 x 2 x 0.9)
Weight g (oz) 119.7 (4.2)
Heatsink (Base) Temperature Range
4
C (F) 0 - 75 (32 - 167)
Storage Temperature Range C (F) -40 - 85 (-40 - 185)
P1 Connector - 16-pin, 2.54 mm spaced header
P2 Connector - 22-pin, 2.54 mm spaced, dual-row header
P3 Connector - 22-pin, 2.54 mm spaced, dual-row header
Notes
1. Maximum duration of peak current is ~2 seconds.
2. Lower inductance is acceptable for bus voltages well below maximum. Use external inductance to meet requirements.
3. Requires a 100F/200V electrolytic capacitor near the P2 Power Connector between High Voltage and Power Ground pins.
4. Additional cooling and/or heatsink may be required to achieve rated performance.
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:


Release Date:
10/8/2010
Revision:
2.01
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 4 of 7

PIN FUNCTIONS
P1 - Signal Connector
Pin Name Description / Notes I/O
1 +REF IN Differential Reference Input (10 V Operating Range, 15 V Maximum Input) I
2 SIGNAL GND Signal Ground GND
3 -REF IN Differential Reference Input (10 V Operating Range, 15 V Maximum Input) I
4 CURRENT MONITOR
Current Monitor. Analog output signal proportional to the actual current output. Scaling is 6.6
A/V. Measure relative to signal ground.
O
5 INHIBIT IN
TTL level (+5 V) inhibit/enable input. Leave open to enable drive. Pull to ground to inhibit
drive. Inhibit turns off all power devices.
I
6 +6V 30mA OUT +6V @ 30mA power supply for customer use. O
7 SIGNAL GND Signal Ground GND
8 RESERVED -
9 RESERVED -
10 RESERVED
Reserved
-
11 CURRENT REFERENCE
Measures the command signal to the internal current-loop. This pin has a maximum output
of 7.3 V when the drive outputs maximum peak current. Measure relative to signal ground.
O
12 FAULT OUT
TTL level (+5 V) output becomes high when power devices are disabled due to at least one
of the following conditions: inhibit, invalid Hall state, output short circuit, over voltage, over
temperature, power-up reset.
O
13 RESERVED -
14 RESERVED -
15 RESERVED -
16 RESERVED
Reserved
-

P2 and P3- Power Connectors
Pin Name Description / Notes I/O
1b 1a HIGH VOLTAGE I
2b 2a HIGH VOLTAGE
DC Power Input. 3A Continuous Current Rating Per Pin.
I
3b NC Not Connected (Reserved) -
3a NC (KEY) Key: No Connection (pin removed) for P2. Not Connected (Reserved) for P3. -
4b 4a PWR GND GND
5b 5a PWR GND
Power Ground (Common With Signal Ground). 3A Continuous Current Rating Per Pin.
GND
6b 6a RESERVED -
7b 7a RESERVED
Reserved
-
8b 8a MOTOR B O
9b 9a MOTOR B
Motor Phase B. 3A Continuous Current Rating Per Pin.
O
10b 10a MOTOR A O
11b 11a MOTOR A
Motor Phase A. 3A Continuous Current Rating Per Pin.
O

HARDWARE SETTINGS
Jumper Settings
Jumper is a SMT, 0 ohm resistor located on the underside of the drive PCB. By default, the drive is configured with the jumper
installed. Typical drive operation will not require the jumper to be removed. Please contact the factory before jumper removal.

Jumper Description Configuration
SMT Jumper (0 Resistor) Not Installed Installed
JE1
Inhibit logic. Sets the logic level of inhibit pins. Labeled JE1 on the PCB of the
drive.
Low Enable Low Inhibit
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:


MECHANICAL INFORMATION
P1 - Signal Connector
Connector Information 16-pin, 2.54 mm spaced header
Details Samtec: BCS-116-L-S-PE
Mating Connector
Included with Drive No
+REF IN 1
SIGNAL GND 2
-REF IN 3
CURRENT MONITOR 4
INHIBIT IN 5
SIGNAL GND 7
CURRENT REFERENCE 11
FAULT OUT 12
+6V 30mA OUT 6

P2 - Power Connector
Connector Information 22-pin, 2.54 mm spaced, dual-row header
Details Samtec: SSM-111-L-DV
Mating Connector
HIGH VOLTAGE 1b
HIGH VOLTAGE 1a
HIGH VOLTAGE 2b
HIGH VOLTAGE 2a
NC 3b
NC (KEY) 3a
PWR GND 4b
PWR GND 4a
PWR GND 5b
PWR GND 5a
MOTOR B 8b
MOTOR B 9a
MOTOR B 8a
MOTOR A 10a
MOTOR A 11a
MOTOR A 11b
MOTOR A 10b
MOTOR B 9b

P3 - Power Connector
Connector Information 22-pin, 2.54 mm spaced, dual-row header
Details Samtec: SSM-111-L-DV
Mating Connector
HIGH VOLTAGE 1b
HIGH VOLTAGE 1a
HIGH VOLTAGE 2b
HIGH VOLTAGE 2a
NC 3b
NC 3a
PWR GND 4b
PWR GND 4a
PWR GND 5b
PWR GND 5a
MOTOR B 8b
MOTOR B 9a
MOTOR B 8a
MOTOR A 10a
MOTOR A 11a
MOTOR A 11b
MOTOR A 10b
MOTOR B 9b

Release Date:
10/8/2010
Revision:
2.01
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 5 of 7

ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:


MOUNTING DIMENSIONS

Release Date:
10/8/2010
Revision:
2.01
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 6 of 7

ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:


PART NUMBERING INFORMATION
A 20 20 -
Blank: Current Mode only
E: Encoder Velocity Mode Available
H: Hall velocity Mode Available
Brushed Drive Blank:
AZ Analog Drive Series
AZ
Drive Type
DDC: Brushed Drive, PWM Command
B: Brushless drive
BDC: Brushless Drive, PWM Command
Feedback Supported
6: 6 Peak, 3 Continuous
8: 80
Standard Environmental Ratings Blank:
Environment Option
X: EXTended Environmental Ratings
Inverted Inhibit Logic INV:
*Options available for orders with sufficient volume.
Contact ADVANCED Motion Controls for more information.
20: 175
Peak Current (Amps)
Max DC Bus Voltage (~1:10 in Volts)
PWM Command
Revision
Additional Options*
Assigned a letter (A through Z) by manufacturer
175V models
80V models

ADVANCED Motion Controls AZ series of servo drives are available in many configurations. All models listed in the selection tables
of the website are readily available, standard product offerings.

ADVANCED Motion Controls also has the capability to promptly develop and deliver specified products for OEMs with volume
requests. Our Applications and Engineering Departments will work closely with your design team through all stages of
development in order to provide the best servo drive solution for your system. Equipped with on-site manufacturing for quick-
turn customs capabilities, ADVANCED Motion Controls utilizes our years of engineering and manufacturing expertise to decrease
your costs and time-to-market while increasing system quality and reliability.

Examples of Modifications and Customized Products
Integration of Drive into Motor Housing Integrate OEM Circuitry onto Drive PCB
Mount OEM PCB onto Drive Without Cables Custom Control Loop Tuned to Motor Characteristics
Multi-axis Configuration for Compact System Custom I/O Interface for System Compatibility
Custom PCB and Baseplate for Optimized Footprint Preset Switches and Pots to Reduce User Setup
RTV/Epoxy Components for High Vibration Optimized Switching Frequency
OEM Specified Connectors for Instant Compatibility Ramped Velocity Command for Smooth Acceleration
OEM Specified Silkscreen for Custom Appearance Remove Unused Features to Reduce OEM Cost
Increased Thermal Limits for High Temp. Operation Application Specific Current and Voltage Limits

Feel free to contact Applications Engineering for further information and details.

Available Accessories
ADVANCED Motion Controls offers a variety of accessories designed to facilitate drive integration into a servo system.
Visit www.a-m-c.com to see which accessories will assist with your application design and implementation.

Power Supplies

Mounting Card
MC1XAZ01
Shunt Regulators

Filter Cards
Release Date:
10/8/2010
Revision:
2.01
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 7 of 7

Drive(s)

To Motor

All specifications in this document are subject to change without written notice. Actual product may differ from pictures provided in this document.
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:

Analog Servo Drive: Description Power Range

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Analog Servo Drive: Description Power Range

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Analog Servo Drive: Description Power Range

Uploaded by

Copyright:

Available Formats

Analog Servo Drive AZ20A20

Description Power Range

20: 20 Peak, 12 Continuous

40: 40 Peak, 20 Continuous

You might also like