M/V Series Servo Drive AB250A060

Release Date:
8/30/2013
Revision:
2.01
Advanced Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 1 of 11

Description Power Range
AB250A060 servo amplifiers are designed to drive
brushless DC motors at a high switching frequency. It
is fully protected against over-voltage, over-current,
over-heating, under-voltage and short-circuits. This
model interfaces with digital controllers or can be used
as a stand-alone drive and requires only a single
unregulated DC power supply or battery. A single
red/green LED and a single digital output indicate
operating status. Loop gain, current limit, input gain,
and offset can be adjusted using 14-turn
potentiometers. The offset adjusting potentiometer
can also be used as an on-board input signal for
testing purposes. It will accept tachometer input,
quadrature encoder inputs, or Hall sensor inputs for
velocity control.
Peak Current (10 seconds) 250 A
Continuous Current 150 A
Supply Voltage 20 - 54 VDC


Features

Four Quadrant Regenerative Operation
Ramped Command Input Adjustment
Drive Brushed or Brushless Motors
Compact Size, High Power Density
Selectable 120/60 Hall Commutation Phasing
Offset Adjustment Potentiometer
Ingress Protection Rating: IP65
Selectable Inhibit/Enable Logic
Adjustable Current Limits
Multiple Modes of Operation




MODES OF OPERATION
Current
Voltage
Duty Cycle (Open Loop)
IR Compensation
Velocity
Hall Velocity
COMMAND SOURCE
10V Analog

FEEDBACK SUPPORTED
Halls
Incremental Encoder
Tachometer (60 DC)
INPUTS/OUTPUTS
Inhibit/Enable Input
Current Monitor Output
Velocity Monitor Output
Fault Output

COMPLIANCES & AGENCY APPROVALS
UL
cUL
RoHS
CE Pending

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

M/V Series Servo Drive AB250A060



Release Date:
8/30/2013
Revision:
2.01
Advanced Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 2 of 11

BLOCK DIAGRAM
LOOP INTEGRATOR
VELOCITY CURRENT LOOP
VARIABLE
RC-BLOCK
POT3
POT1
ON - RAMP
OFF- NO RAMP
SW1-5 SW1-4 SW1-3
20k
10k..310k
-
+
10k
20.8k
P1-5 PGND
CURRENT
SENSE
B+
B-
NC P1-6
PGND
HVIN
MOTOR B
MC
MOTOR A MA
MB
H-BRIDGE
MOTOR C
3-Phase
-
+
S
W
1
-
8
PWM AND
CONTROL
LOGIC
SW1-9
V
e
l
D
i
r
INH SEL
C
u
r
r
/
V
e
l
D
E
G
F
A
U
L
T
I
N
H
/
E
N
A
B
L
E
10nF
S
W
1
-
2
SW1-7
SW3-1..5
5nF..82nF
CF1*
DC-TO-DC
Peak/Cont.
CURRENT
LIMIT
SW3-6..10
20k
+5VI
P1-12 INH/ENABLE
5k
10k
CW
100k
-
+
10k
CW
SW1-10
RAMP
30k 10k
1nF
20k
+REF P1-1
20k
-
+
30k 10k
1nF
-REF P1-2
SW1-1
POT4
100k
+5V
5k
-5V
OFFSET
TEST
CW
CW
Min: 0.1s/V
Max: 1.8s/V
3.3k
10k
HALL/ENC
CONV.
RECOMMENDED SETTINGS FOR CURRENT MODE - POT1 FULLY CCW, POT3 FULLY CW
LED GREEN - NORMAL OPERATION, LED RED - FAULT
DRIVES ARE SHIPPED IN CURRENT MODE WITH MAXIMUM CURRENT SETTINGS
* OPTIONAL USER INSTALLED THROUGH HOLE COMPONENTS
FOR OTHER SWITCH FUNCTIONS SEE SWITCH DESCRIPTION
10k
P
1
-
1
5
10k
10k
P
1
-
1
9
S
W
1
-
6
50k
INTERNAL
CONVERTER
DC-TO-DC
+10V USER (3mA) P1-3
P1-4 -10V USER (3mA)
R
F
2
*
P
1
-
2
3
P
1
-
2
2
P
1
-
1
7
N/A
ON
ON
N/A
OFF
OFF
OFF
N/A
ON
OFF
N/A
ON
ON N/A
ON
SW1-6 SW1-7
HALL VELOCITY
SW1-3 MODE SELECTION
CURRENT
SW1-5 SW1-4
N/A
OFF
OFF
X
X
OFF
X
X
N/A - NOT APPLICABLE
TACHOMETER
X - DEPENDENT ON APPLICATION
OFF IR COMPENSATION**
ON
ENCODER VELOCITY OFF
DUTY CYCLE
OFF
OFF
OFF OFF
P
1
-
7
P
G
N
D
P1-16
P1-10 SGND
P1-11 SGND
P
1
-
8
N
C
10k
P
1
-
1
3
P
1
-
1
4
P
1
-
2
0
P
1
-
2
1
20k
+5VI
Q2
2222
P1-18 FAULT-OUT
FAULT
SGND P1-9
10k
CW
LIMIT
POT2
U34
H1,H2,H3 ON=120
CF2*
2.2uF
0.47uF
U31
AB250A060 FUNCTIONAL BLOCK DIAGRAM
CURRENT
100k U32
U15
POT5
LOOP GAIN
U20 REF IN
VELOCITY
+5VHE
ENC A,B
H
3
C
U
R
R
E
N
T

M
O
N
I
T
O
R
VOLTAGE FEEDBACK
DUTY CYCLE FEEDBACK
IR-COMPENSATION
VELOCITY MODE SELECTOR
H1,H2,H3
ENC A,B
C
U
R
R
E
N
T

L
O
O
P
OFF=60
ON=CM
OFF=VM
CURRENT FEEDBACK
V
E
L
O
C
I
T
Y

M
O
N
I
T
O
R
T
A
C
H
-
I
N
+
5
V
H
E

(
2
5
0
m
A
)
H
1
H
2
E
N
C
B
E
N
C
A
+5VHE
RF1*
**IR COMPENSATION MODE REQUIRES USER INSTALLED RESISTOR RF1 ON PCB
SGND
OFF OFF OFF OFF VOLTAGE X



Information on Approvals and Compliances

US and Canadian safety compliance with UL 508c, the industrial standard for power conversion electronics. UL
registered under file number E140173. Note that machine components compliant with UL are considered UL
registered as opposed to UL listed as would be the case for commercial products.

RoHS (Reduction of Hazardous Substances) is intended to prevent hazardous substances such as lead from being
manufactured in electrical and electronic equipment.
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

M/V Series Servo Drive AB250A060



Release Date:
8/30/2013
Revision:
2.01
Advanced Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 3 of 11

SPECIFICATIONS
Power Specifications
Description Units Value
DC Supply Voltage Range VDC 20 - 54
DC Bus Over Voltage Limit VDC 59
DC Bus Under Voltage Limit VDC 18
Logic Supply Voltage (Keyswitch) VDC 20 - 54
MaximumPeak Output Current
1
A 250
MaximumContinuous Output Current A 150
Max. Continuous Output Power W 7695
Max. Continuous Power Dissipation W 405
Internal Bus Capacitance F 12600
MinimumLoad Inductance (Line-To-Line)
2
H 200
Switching Frequency kHz 14.5
MaximumOutput PWM Duty Cycle % 100
Control Specifications
Description Units Value
Command Sources - 10V Analog
Feedback Supported - Halls, Incremental Encoder, Tachometer (60 VDC)
Commutation Methods - Trapezoidal
Modes of Operation - Current, Voltage, IR Compensation, Duty Cycle (Open Loop), Hall Velocity, Velocity
Motors Supported - Single Phase (Brushed, Voice Coil, Inductive Load), Three Phase (Brushless)
Hardware Protection -
Over Current, Over Temperature, Over Voltage, Short Circuit (Phase-Phase & Phase-Ground),
Under Voltage
Mechanical Specifications
Description Units Value
Agency Approvals - cUL, UL, RoHS, CE Pending
Size (H x W x D) mm(in) 203.2 x 139.7 x 59.7 (8.0 x 5.5 x 2.4)
Size (H x W x D) with 23-pin mating connector installed mm(in) 203.2 x 139.7 x 74.0 (8.0 x 5.5 x 2.9)
Weight g (oz) 1638.60 (57.80)
Heatsink (Base) Temperature Range
3
C (F) 0 - 75 (32 - 167)
Storage Temperature Range C (F) -20 - 85 (-4 - 185)
Cooling System
3
- Natural Convection
FormFactor - Vehicle Mount
IP Rating - 65
I/O Connector - 23-pin, AMPSEAL connector
MOTOR POWER Connector - 3 Individual M6 threaded terminals
POWER Connector - 2 Individual M6 threaded terminals
Notes
1. Maximum duration of peak current is ~5 seconds for zero-to-peak current command, and ~10 seconds for peak-to-peak current command.
2. Lower inductance is acceptable for bus voltages well below maximum. Use external inductance to meet requirements.
3. Additional cooling and/or heatsink is required to achieve rated performance. Thermal grease recommended between baseplate and external heatsink.




Mating Connector Kit
Mating connector housing, socket contacts, and seal plugs can be ordered as a kit using ADVANCED Motion Controls part number
KC-23AMPSEAL01.

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

M/V Series Servo Drive AB250A060



Release Date:
8/30/2013
Revision:
2.01
Advanced Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 4 of 11

PIN FUNCTIONS

I/O - Signal Connector
Pin Name Description / Notes I/O
1 +REF IN
Differential Reference Input (10 V Operating Range, 15 V Maximum Input)
I
2 -REF IN I
3 +10V 3mA OUT 10 V @ 3 mA low power supply for customer use. Short Circuit Protected. Reference
ground common with signal ground.
O
4 -10V 3mA OUT O
5 POWER GROUND Power Ground PGND
6 RESERVED Reserved -
7 POWER GROUND Power Ground (Low Current. 500 mA max) PGND
8 RESERVED Reserved -
9 SIGNAL GROUND
Signal Ground
SGND
10 SIGNAL GROUND SGND
11 SIGNAL GROUND SGND
12 INHIBIT/ENABLE
This TTL level input signal turns off all power devices of the Hbridge when pulled to Signal
Ground with SW1-9=ON. If SW1-9=OFF, pulling this pin to Signal Ground will enable the
drive.
I
13 HALL 1
Hall sensor inputs. Logic levels: maximum low level input is 1.5 VDC, minimum high level
input is 3.5 VDC. Reference to Power Ground.
I
14 HALL 2 I
15 HALL 3 I
16 SIGNAL GROUND Signal Ground SGND
17 VELOCITY MONITOR
1V =21.5 kHz Encoder Frequency; 1V =98.5 Hz Hall Sensor Frequency. Reference to
Power Ground.
O
18 FAULT OUT
This output activates during short circuit, over-voltage, under voltage, inhibit, over-
temperature and power-on reset. A red LED also indicates a fault condition. Reference to
Signal Ground. Can be used with an external voltage supply and LED for visual fault
indication.
O
19 CURRENT MONITOR
Scaling factor =27.6 A/V. This output represents the actual motor output current. Reference
to Power Ground.
O
20 ENCODER A Encoder Channel A. Reference to Power Ground. I
21 ENCODER B Encoder Channel B. Reference to Power Ground. I
22 +5V OUT +5V @ 150mA. For customer use. Reference to Power Ground. O
23 TACH Tachometer Input, 60k ohm input resistance, 60 V max. Reference to Power Ground. I

MOTOR POWER - Power Connector
Terminal Name Description / Notes I/O
MA MOTOR A Motor Phase A O
MB MOTOR B Motor Phase B O
MC MOTOR C Motor Phase C O

POWER - Power Connector
Terminal Name Description / Notes I/O
B- POWER GROUND Power Ground PGND
B+ HIGH VOLTAGE DC Power Input. Battery Power. I


















ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

M/V Series Servo Drive AB250A060



Release Date:
8/30/2013
Revision:
2.01
Advanced Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 5 of 11

HARDWARE SETTINGS
Switch Functions
SW1
Switch Description
Setting
On Off
1
Test / Offset controls the sensitivity of the offset pot. This is used
as an on-board reference signal in test mode.
Test Offset
2 120/60 degree commutation phasing. 120 degree phasing 60 degree phasing
3 Mode Select. Refer to Mode Selection Table Duty-Cycle / Hall IR Comp / Encoder
4 Mode Select. Refer to Mode Selection Table Hall / Encoder Duty-Cycle / Voltage
5 Mode Select. Refer to Mode Selection Table Tach Mode Other Modes
6 Mode Select. Refer to Mode Selection Table Current Mode Velocity Modes
7 Velocity Integrator Capacitor
More Capacitance
(ON for Hall Velocity Mode)
Less Capacitance
8 Velocity Feedback Polarity (for Hall or Encoder Velocity Mode) One Direction Opposite Direction
9 Inhibit / Enable Logic Select Ground Inhibit pin to Inhibit
Ground Inhibit enable motor
outputs
10 Ramp Enable Enable Command Ramping No Command Ramping

Mode Selection Table
Operating modes can be selected by setting SW1 DIP switches according to the following table.
Mode SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 SW1-9 SW1-10
CURRENT X X X X OFF ON X X X X
DUTY CYCLE X X ON OFF OFF OFF X X X X
VOLTAGE X X OFF OFF OFF OFF X X X X
IR COMPENSATION* X X OFF OFF OFF OFF X X X X
HALL VELOCITY X X ON ON OFF OFF ON X X X
ENCODER VELOCITY X X OFF ON OFF OFF X X X X
TACHOMETER X X X X ON OFF X X X X
X =does not affect mode
* IR Comp Mode requires the addition of an IR Comp resistor RF1 on the PCB.

Current Loop Tuning Values
SW3 DIP switches add additional resistance and capacitance to the current loop tuning circuitry. SW3 switches 1-5 add additional
parallel capacitance to the current loop integrator capacitor, and SW3 switches 6-10 add additional series resistance to the
current loop gain resistor (see Block Diagram). Capacitance and resistance values are given in the tables below along with the
appropriate DIP switch settings.

SW3
Switch
Additional Current Loop Integrator Capacitance (F)
SHORT .082 .077 .072 .067 .062 .057 .052 .047 .035 .030 .025 .020 .015 .010 .005 OPEN
1 ON ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF
2 ON ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF
3 ON ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF
4 ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF
5 ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

M/V Series Servo Drive AB250A060



Release Date:
8/30/2013
Revision:
2.01
Advanced Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 6 of 11

SW3
Switch
Additional Current Loop Gain Resistance (k)
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
6 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF
7 ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF
8 ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF
9 ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF
10 ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
Switch
(continued)
160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310
6 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF
7 ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF
8 ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF
9 ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF
10 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF

Potentiometer Functions
Potentiometer Description Turning CW
Pot 1
Loop gain adjustment in duty cycle and velocity modes. Turn this pot fully CCW in
current mode.
Increases loop gain
Pot 2
Current limit. This potentiometer adjusts both the continuous and peak current limit
while maintaining the continuous to peak ratio (60%).
Increases current limit
Pot 3
Reference in gain. This potentiometer adjusts the ratio between input signal and
output variables (voltage, current, and velocity).
Increases reference input gain
Pot 4
Test/Offset. Used to adjust any imbalance in the input signal or in the drive. When
SW1-1 (DIP switch) is ON, the sensitivity of this pot is greatly increased allowing it to
be used as an on-board signal source for testing purposes.
Zero speed setting is at the
midpoint of this 14-turn pot.
Pot 5 Ramp Time. Sets the ramp time for the command input signal.
Decreases ramp time
(faster response time)
Note: Potentiometers are approximately linear and have 12 active turns plus 1 inactive turn on each end.

Ramping (Pot 5):
The built-in ramp circuit allows the command input to be ramped linearly. This feature is activated by setting SW1-10 = ON. The
ramp time can be set for up to 20 seconds in reaching the max command by adjusting Pot 5 fully counter-clockwise. Ramping
rates are linear with respect to time and apply to both directions of motion. For example, if the single-ended command input is
only 2.5 Volts, the time to ramp to this voltage would be half the time to ramp to 5 Volts.
Current Limit Adjustments:
These amplifiers feature separate peak and continuous current limits. The current limit adjustment Pot 2 adjusts both peak and
continuous current limit at the same time. Pot 2 has 12 active turns and one inactive turn on each end and is approximately
linear. Thus, to adjust the current limit turn the potentiometer counter-clockwise to zero, then turn clockwise to the appropriate
value.


ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

M/V Series Servo Drive AB250A060



Release Date:
8/30/2013
Revision:
2.01
Advanced Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 7 of 11

Through-hole Components

Location Description
CF2*
Velocity Loop Integrator. Through-hole capacitor that can be added for more precise velocity loop tuning. See section
below on Tuning with Through-hole components for more details.
CF1*
Current Loop Integrator. Through-hole capacitor that can be added for more precise current loop tuning. See section
below on Tuning with Through-hole components for more details.
RF2*
Tachometer Gain Scaling. Through-hole resistor that can be added to change the gain of the tachometer input. See
section below on Tachometer Gain for more details.
RF1*
IR Compensation Scaling. Through-hole resistor that can be added to configure the amplifier for IR Compensation mode.
See section below on IR Compensation Notes for more details.
Tuning With Through-hole Components
In general, the drive will not need to be further tuned with through-hole components. However, for applications requiring more
precise tuning than what is offered by the potentiometers and DIP switches, the drive can be manually modified with through-
hole capacitors as denoted in the above table. By default, the through-hole locations are not populated when the drive is shipped.
Before attempting to add through-hole components to the board, consult the section on loop tuning in the installation notes on
the manufacturers website. A general rule of thumb to follow when adding through-hole components is:
A larger capacitor value will increase the integration time, and therefore create a slower response time.
Proper tuning using the through-hole components will require careful observation of the loop response on a digital oscilloscope to
find the optimal through-hole component values for the specific application.
Tachometer Gain
Some applications may require an increase in the gain of the tachometer input signal. This occurrence will be most common in
designs where the tachometer input has a low voltage to RPM scaling ratio. The drive offers a through-hole location listed in the
above table where a resistor can be added to increase the tachometer gain. Use the drives block diagram to determine an
appropriate resistor value.
IR Compensation
For applications that will use IR Compensation mode, a resistor can be added to the location named in the table above. The
combination of the added resistor and correct DIP switch settings will configure the amplifier for IR Compensation mode. While in
IR Compensation mode, the amplifier will adjust the duty cycle to compensate for changes in the output current. Consult the
amplifiers functional block diagram and the manufacturers website for more information.

NOTE: DAMAGE DONE TO THE DRIVE WHILE PERFORMING THESE MODIFICATIONS WILL VOID THE WARRANTY.


ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

M/V Series Servo Drive AB250A060



Release Date:
8/30/2013
Revision:
2.01
Advanced Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 8 of 11

MECHANICAL INFORMATION
I/O - Signal Connector
Connector Information 23-pin, AMPSEAL connector
Mating Connector
Details
TE Connectivity: Housing P/N 770680-1; Socket Contacts P/N 770854-3 (loose); Seal Plug P/N
770678-1; Crimp Tool P/N 58529-1
Included with Drive No
1 +REF IN 15 HALL 3
16 SIGNAL GROUND
2 -REF IN
3 +10V 3mA OUT
4 -10V 3mA OUT
5 POWER GROUND
6 RESERVED
7 POWER GROUND
8 RESERVED
14 HALL 2
13 HALL 1
12 INHIBIT/ENABLE
11 SIGNAL GROUND
10 SIGNAL GROUND
9 SIGNAL GROUND
17 VELOCITY MONITOR
18 FAULT OUT
19 CURRENT MONITOR
20 ENCODER A
21 ENCODER B
22 +5V OUT
23 TACH


MOTOR POWER - Power Connector
Connector Information Three individual M6 threaded terminal
Mating Connector
Details M6 screw or bolt with washer
Included with Drive Yes

POWER - Power Connector
Connector Information Two individual M6 threaded terminal
Mating Connector
Details M6 screw or bolt with washer
Included with Drive Yes





ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

M/V Series Servo Drive AB250A060



Release Date:
8/30/2013
Revision:
2.01
Advanced Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 9 of 11

WIRING DIAGRAM
Motor
Hall
Sensors
Inhibit
Power Fuse
High
Voltage
Power
GND
Motor A
Motor B
Motor C
Hall 1
*+5V Supply
Hall 3
Hall 2
Power GND
Fault Out
-10V Supply
+10V Supply
DC Power
Input
Tach
Tach -
Tach Return /
Power GND
Throttle
Pot
+Ref In
-Ref In
NOTE: All
Feedback
cannot be
supported at
one time
ON board Status LED
Current Monitor
V
Ud
Current
Velocity Monitor
Isolation (on 200V drives)
V
Ud
Speed
Chassis GND
Power GND
Signal Ground
Encoder
Encoder A
Encoder B
*+5V Supply
Power GND
*+5V Supply
is only one
connection pin
LED
+5VDC
500 ohm

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

M/V Series Servo Drive AB250A060



Release Date:
8/30/2013
Revision:
2.01
Advanced Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 10 of 11

MOUNTING DIMENSIONS

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

M/V Series Servo Drive AB250A060



Release Date:
8/30/2013
Revision:
2.01
Advanced Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 11 of 11

PART NUMBERING INFORMATION
A 060 250
Peak Current
Brushless Motor B:
Motor Type
Maximum peak current rating in Amps
Standard Analog Blank:
Drive Type
V: Vehicle (0-5V, 0-5K)
A B
Peak/Continuous Ratio
Continuous =~0.6Peak A:
Continuous =Peak C:
Maximum Voltage
54V Over-Voltage 060:
88V Over-Voltage 100:
190V Over-Voltage 200:
Analog Servo Drive


ADVANCED Motion Controls servo drives are available in many configurations. Note that not all possible part number
combinations are offered as standard drives. All models listed in the selection tables of the website are readily available, standard
product offerings.

ADVANCED Motion Controls also has the capability to promptly develop and deliver specified products for OEMs with volume
requests. Our Applications and Engineering Departments will work closely with your design team through all stages of
development in order to provide the best servo drive solution for your system. Equipped with on-site manufacturing for quick-
turn customs capabilities, ADVANCED Motion Controls utilizes our years of engineering and manufacturing expertise to decrease
your costs and time-to-market while increasing system quality and reliability.

Examples of Customized Products
Integration of Drive into Motor Housing Integrate OEM Circuitry onto Drive PCB
Mount OEM PCB onto Drive Without Cables Custom Control Loop Tuned to Motor Characteristics
Multi-axis Configuration for Compact System Custom I/O Interface for System Compatibility
Custom PCB and Baseplate for Optimized Footprint Preset Switches and Pots to Reduce User Setup
RTV/Epoxy Components for High Vibration Optimized Switching Frequency
OEM Specified Connectors for Instant Compatibility Ramped Velocity Command for Smooth Acceleration
OEM Specified Silkscreen for Custom Appearance Remove Unused Features to Reduce OEM Cost
Increased Thermal Limits for High Temp. Operation Application Specific Current and Voltage Limits

Feel free to contact Applications Engineering for further information and details.























All specifications in this document are subject to change without written notice. Actual product may differ from pictures provided in this document.
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By: