Scribd
Upload
34 views2 pages

Practiva 1-2 Ccna

The document shows the configuration of a router interface. It configures IP address 10.1.1.1 on interface FastEthernet0/0 and performs ping tests to different IP addresses on the subnet and shows the interface status and configuration.

Uploaded by

Linda Lizzy Liemka
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
34 views2 pages

Practiva 1-2 Ccna

The document shows the configuration of a router interface. It configures IP address 10.1.1.1 on interface FastEthernet0/0 and performs ping tests to different IP addresses on the subnet and shows the interface status and configuration.

Uploaded by

Linda Lizzy Liemka
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

Router

--- System Configuration Dialog ---


Continue with configuration dialog? [yes/no]: n
Press RETURN to get started!
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#show int e0/0
^
% Invalid input detected at '^' marker.
Router(config)#do show int brief
show int brief
^
% Invalid input detected at '^' marker.
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
show int brief
^
% Invalid input detected at '^' marker.
Router#show ip int brief
Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 unassigned YES unset administratively down down

FastEthernet0/1 unassigned YES unset administratively down down

Vlan1 unassigned YES unset administratively down down
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#ip address 10.1.1.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state t
o up
Router(config-if)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
ping 10.1.1.11
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.11, timeout is 2 seconds:
..!!!
Success rate is 60 percent (3/5), round-trip min/avg/max = 3/4/5 ms
Router#ping 10.1.1.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.10, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Router#ping 10.1.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.100, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 7/8/9 ms
Router#show logging
Syslog logging: enabled (0 messages dropped, 0 messages rate-limited,
0 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
Console logging: level debugging, 4 messages logged, xml disabled,
filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
filtering disabled
Buffer logging: disabled, xml disabled,
filtering disabled
Logging Exception size (4096 bytes)
Count and timestamp logging messages: disabled
Persistent logging: disabled
No active filter modules.
ESM: 0 messages dropped
Trap logging: level informational, 4 message lines logged
Router#show ip int brief
Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 10.1.1.1 YES manual up up

FastEthernet0/1 unassigned YES unset administratively down down

Vlan1 unassigned YES unset administratively down down
Router#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state t
o down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state t
o up
Router#copy run start
Router#copy run startup-config
Destination filename [startup-config]?
Building configuration...

You might also like