DRESSER Regulators Flowgrid

Download as pdf or txt
Download as pdf or txt
You are on page 1of 12
At a glance
Powered by AI
The document discusses the features and operation of the Mooney Flowgrid regulator, which was designed for easy maintenance in pressure and flow control applications.

The regulator has features like in-line maintenance with minimal parts, a rugged diaphragm, elliptical main spring, and over eighty-eight valve body options to fit any application.

It controls pressure and flow using a pilot regulator and spring case to open and close a throttling element based on downstream demand.

MOONEY

FLOWGRID

REGULATORS
The Flowgrid

Regulator is designed
for ease of maintenance
2 | Dresser
Mooney

Flowgrid

Regulator
The Mooney

Flowgrid

regulator was designed to fill the need for an easy-to-maintain valve that would be
used primarily with self-contained pilot systems for pressure or flow control of almost any gas or liquid.These
key design elements equate to increased productivity.
Extremely high accuracy of control, incredible responsiveness, wide rangeability, minimal parts and top entry
access to all components makes the Mooney Flowgrid regulator the regulator of choice. Our customers tell us
what they like most about the Mooney

Flowgrid regulator is....


Features
In-line maintenance with minimal parts
Rugged fabric-reinforced throttling element/diaphragm
provides wide-rangeability, stability and fast response in
severe service conditions
Elliptical main spring provides a high frequency
response, proportional action for stability, a consistent
low minimum differential and shut off force
Spring case has small volume to enhance speed of
response and stability
Over eighty-eight valve body options to fit any
application
you just set it and forget it.
Throttle plates offered in four standard capacities 100%,
50%, 75% and 35% or any custom capacity desired
Symmetrical throttle plate design inhibits debris from
accumulating under the seat and effecting shut-off
Drilled-hole throttle plates for reduced noise and extended
diaphragm life
Equal inlet/outlet pressure rating for all sizes assures easy
operation with no special start-up procedures
Dual-port valve design provides redundancy with dual pilots
and extra capacity with one pilot
Compact size for easy installation in any position
Mooney Flowgrid Regulator | 3
4 | Dresser
Pressure Relieving Valve
At no flow, when the outlet pressure is greater than the set
point of the Series 20

pilot regulator, the pilot is closed and


full inlet pressure loads the main valve spring case through the
pilot loading connection. In this condition, the main throttling
element is closed tightly against the throttling plate. The
pressure differential across the outlet half of the diaphragm
adds to the spring force to close the valve (Fig 1).
As demand for flow occurs in the downstream system,
the outlet pressure drops, causing the pilot to open and
start bleeding pressure out of the spring case faster than
it can enter through the restricting valve. Reducing the
loading pressure above the diaphragm allows inlet pressure
to progressively lift the diaphragm off the throttling plate,
opening the valve and satisfying the demand for the flow in
the downstream system (Fig 2).
When demand for flow ceases or is reduced, the downstream
pressure increases, causing the pilot regulator to close. Inlet
pressure continues to pass through the restriction until the
loading pressure equals the inlet pressure.
The spring force, plus the pressure differential across the
outlet half of the throttling plate closes the throttling element
against the throttling plate closing the main valve (Fig 1).
Adjustment of the variable restricting valve affects the
response rate, stability and sensitivity of the regulator. Smaller
restrictor openings result in higher gain (sensitivity) and slower
closing speeds. Larger openings result in lower gain (greater
proportional band), greater stability, and faster closing speed.
Back Pressure Valve
In a back pressure relief application (BPV) the valve functions
in the exact same way as previously described except that
the sense line for the control pilot is located upstream of the
regulator. The action of the pilot is the reverse of a pressure
reducing pilot such that the pilot opens when system pressure
increases above its set-point. The pilot will close when the
system pressure is less than its set-point (Fig 3).
Principle of Operation
PILOT LOADING
CONNECTION
PILOT SUPPLY
INLET OUTLET
PILOT OUTLET
CONNECTION
RESTRICTOR
PILOT SENSE
CONNECTION
PILOT SUPPLY
PILOT LOADING
CONNECTION
PILOT SENSE
CONNECTION
INLET OUTLET
PILOT OUTLET
CONNECTION
RESTRICTOR
PILOT SENSE
CONNECTION
PILOT LOADING
CONNECTION
PILOT SUPPLY
INLET OUTLET
PILOT OUTLET
CONNECTION
RESTRICTOR
Fig 1. Pressure Reducing Conguration Fully Closed.
Fig 2. Pressure Reducing Conguration Partially Open.
Fig 3. Back Pressure Valve
Applications
The Flowgrid

is ideal for pressure reducing (PRV), back pressure


or relief (BPV), flow-control, and multi-function control applications
where good regulation, simplicity, and ease of maintenance are of
prime importance.
The Flowgrid can handle gas and liquids that are relatively clean,
noncorrosive, and compatible with standard carbon steel/17-4ph
stainless steel/nitrile rubber construction. The normal temperature
range is -20F to 150F. Alternative materials for conditions outside
the normal temperature range are available.
The Flowgrid can easily be interfaced with conventional pneumatic,
electronic or microprocessor-based controllers for a variety of
pressure and flow control applications. These applications can
often result in lower overall costs and substantial energy savings.
Natural Gas Industry Applications
District Regulator
Monitor Regulator
Relief Valve (BPV)
Flow Control
Compressor Fuel Gas
Co-generation Fuel Supply
Industrial Applications
Boiler Fuel Gas
Oil

Water
Industrial Gasses (e.g., air, nitrogen, argon)
Bi-directional Pressure Control
Check Valve
Differential Control Pressure or Flow
Set-Point Control
The Jordan

1020 Actuator connected directly to any Series 20

pilot allows
remote control of any set point between 5 i.w.c. and 900 psig. The actuator
is available in a variety of electrical classications, voltages and input signals.
input signals.
Pneumatic Control Application
A pneumatic input signal to a Badger

Control Pilot mounted on


a Flowgrid

valve offers a variety of pressure, ow and remote


set point options.
Remote control of the Series 20

pilot set point is also possible


by pressure loading the spring case through the tapped vent
connection.
Mooney Flowgrid Regulator | 5
Standby Monitor System (Fig 4)
Under normal operating conditions, one of the Flowgrid

regulators operates as a worker while the other acts as a


monitor of the system. The upstream or downstream regulator can serve either function.
The monitor pilot is set at a slightly higher pressure than the worker (e.g., +5%). If the operating regulator should
fail, P2 will increase until it reaches the set point of the monitor pilot, allowing the monitor regulator to take over
protecting the downstream system P2 from being over pressured.
NOTE: On dead-end systems, a token relief downstream of the second stage regulator is recommended to
compensate for slight leaks due to wear or debris in the monitor regulator and/or operating regulator.
NOTE: Ref. Fig 4. Use alternative outlet to insure full capacity when the pressure drops across the regulator are
less than 60 psid. NOTE: System will shut off at upstream pilot setting.
Working Monitor System (Fig 5)
Under normal conditions, both Flowgrid

regulators are working to reduce pressure in a two-stage


sequence. If a problem occurs in the upstream regulator, the downstream regulator takes over the entire
pressure cut, maintaining P
3
at the same pressure. If the downstream regulator fails, P
3
will rise, causing
the monitor pilot on the upstream regulator to take over maintaining the pressure in the downstream
system P
3
at the set point of the monitor pilot.
NOTE: On dead-end systems, a token relief downstream of the second stage regulator is recommended
to compensate for slight leaks due to wear or debris in the monitor regulator.
NOTE: An additional benefit of this system is the lower noise level that results when the pressure is
reduced in two stages.
I
O
O L
RESTRICTOR
MONITOR REGULATOR
SERIES 20 PILOT
ALTERNATE OUTLET
If P1 - P2 < 60 psi
I
S
L
OPERATING REGULATOR
RESTRICTOR
S
FLOW
LEGEND
I = INLET
O= OUTLET
S= SENSE
L= LOADING
P2 P1
SERIES 20 PILOT
1ST STAGE PILOT
I
O
O
S
L
RESTRICTOR
1ST STAGE & MONITOR REGULATOR
2ND STAGE PILOT
I
S
L
MONITOR PILOT
2ND STAGE REGULATOR
RESTRICTOR
L
P3 P2 P1
S
O I
FLOW
LEGEND
I = INLET
O= OUTLET
S= SENSE
L= LOADING
6 | Dresser
Mooney Flowgrid Regulator | 7
Sizes 1- 12
Body Styles Single & Dual Port
Body Materials Steel, Ductile Iron*
End Connections Screwed, Socket Weld,
Flanged, Flangeless &
Buttweld
Outlet Pressures 5 i.w.c. - 900 psig
Maximum Operating Differential 800 psid,
1 1000 psid
Maximum Emergency
Differential
1,000 psid (unless limited
by body rating)
1 1500 psid
Cracking Differential 4 1 psid
Temperature Range -20F to 150F
Minimum/Maximum -40F to 175F
Flow Direction Bi-Directional
Specications
* Stainless steel available in some sizes. Factory quote required.
Spring Color Type 20

Pilot
Outlet Presure
Range
White 20L 5-15 i. w. c.
Brown 20L 10-40 i. w. c.
Yellow 20L 1-3 psig
Orange 20L 2-5 psig
Gray 20L 4-8 psig
Spring Color Type 20

Pilot
Outlet Presure
Range
Red 20 3-12 psig
Cadmium 20 10-40 psig
Blue 20 25-90 psig
Purple 20 60-200 psig
Black 20 100-260 psig
White/Green 20 200-450 psig
Black 20HP 200-520 psig
White/Green 20HP 400-900 psig
Pilot available in:
20L Aluminum & Bronze, 20 Brass and SST, 20H Brass and SST
Guidelines for Diaphragm Selection
Compound Temperature
Range
(Degrees F)
Maximum
Differential
1 Value
Maximum
Differential
All Others
Characteristics Recommended Applications
75 Duro
(standard)
-20 to 150 1000 psid 800 psid Best all around material 60 psid to Maximum Differential
60 Duro* -25 to 150 300 psid* 300 psid* Best shutoff at low differential
pressure
Low Differential (100 psid or less) or
low temperature
80 Duro
High ACN
-5 to 175 1000 psid 800 psid Higher abrasion and swelling
resistance
High Differential (400 psid or higher) or
abrasive conditions with distillates
80 Duro
Low ACN
-20 to 150 1000 psid 800 psid Higher abrasion resistance
and low temperature flexibility
High Differential (400 psid or higher) or
abrasive conditions at low temperatures
NOTE: Minimum temperature is dened as lowest temperature for normal valve operation. Valve will operate below this
temperature, but response times may increase and bubble-tight shutoff may be impaired. At extreme low temperatures
below -40 F), exure of the diaphragm may result in cracking of the material. This will require replacement of the diaphragm.
Maximum differentials listed are recommended for best diaphragm life. Exceeding these differentials will not result in
diaphragm damage, but may accelerate wear of the part.
* The 60 durometer diaphragm is standard on the Flowgrid

250 Valve which is a ductile iron and aluminum construction


with a maximum inlet and differential rating of 250 psi.
Valve Performance
Performance with Series 20L

and Series 20

Pilot
Mooney

Series 20L Pilot Pressure Reducing Mode Restrictor Set at 4


Pilot Spring Range Lockup Droop Maximum Capacity
1
Boost @ Constant Flow
White 5 i.w.c. - 15 i.w.c. 1.0. i.w.c. 0.5 i.w.c. 0.7 i.w.c.
Brown 10 i.w.c. - 40 i.w.c. 1.0 i.w.c. 2 i.w.c. 0.7 i.w.c.
Yellow 1-3 psig 0.2 psig 0.15 psig 0.25 psig
Orange 2-5 psig 0.35 psig 0.25 psig 0.25 psig
Gray 4-8 psig .5 psig 0.30 psig 0.25 psig
Mooney

Series 20 Pilot Pressure Reducing Mode Restrictor Set at 4 Back Pressure Mode Restrictor Set
at 4
Pilot Spring Range Lockup Droop
1
Maximum
Capacity
Boost at
2

Constant Flow
Buildup
Maximum
Capacity
Lockup
Red 3-12 psig 1.0 psig .30 .70 psig
4 4
Cadmium 10-40 psig 1.0 psig .30 .70 psig + .50 psig -1.0 psig
Blue 25-90 psig 2.0 psig .60 .70 psig + .50 psig -1.0 psig
Purple 60-200 psig 2.0 psig 1.30 .70 psig + 1.0 psig -1.0 psig
Black 100-260 psig 5.0 psig 2.00 .70 psig + 3.0 psig -1.5 psig
Green 200-450 psig 10.0 psig 4.00 .70 psig + 5.0 psig -2.0 psig
HP Black 200-520 psig 10.0 psig 4.00 1.50 psig + 5.0 psig
3
-3.0 psig
HP Green 400-900 psig 20.0 psig 8.00 1.50 psig +12.0 psig
3
-5.0 psig
1 Inlet pressure (P
1
) constant
2 Per 100 psi decrease in inlet pressure (P
1
)
3 SST/Delrin trim required
0
5
10
15
20
25
30
25% 50% 75% 100%
CAPACITY
D
I
F
F
E
R
E
N
T
I
A
L

P
S
I
D
A
I
B
H
F
E
G
J
D
C
Minimum Pressure Differential Versus Capacity
4 Minimum set point for the Flowgrid Valve and Pilot when used as a relief valve is 15 psig
or the minimum differential, whichever is greater.
A 1 75 Duro, STD Spring
B 1 60 Duro, Low Spring
C 2 LP 75 Duro, STD Spring
D 3 75 Duro. STD Spring
E 2 STD 75 Duro, STD Spring
F 4, 6 75 Duro, STD Spring
G 2 STD 60 Duro, Low Spring
H 4, 6 60 Duro, Low Spring
I 2 LP 60 Duro, Low Spring
J 3 60 Duro, Low Spring
Use the chart at left to determine the
amount of available capacity through
a Flowgrid

valve when the differen-


tial pressure across the regulator falls
below 30 psid.
For example: At 15 psid a 1 single
port valve with a standard main
spring and 75 durometer diaphragm
(A) can flow 50% of total calculated
capacity in this condition. With a
low differential main spring and 60
durometer diaphragm is installed
(B) the valve can flow 100% of its
calculated capacity.
8 | Dresser
Simplied Gas Sizing Equation
In the following term (P
1
-P
2
) /P
1
equals .64 or greater, then
sonic velocity is present in the valve and the simplified version
of the gas-sizing equation may be used.
Air: Q = P
1
Cg Natural Gas: Q = P
1
Cg 1.29
NOTE: Valve sizing and selection software is available for
download at: dresser.com/mooney
Liquid Sizing
Gas Velocity
To avoid generating additional noise in the outlet piping, it is
recommended that the body outlet velocity be limited to
approximately 0.5 of Mach. This equates to approximately
500 ft/sec for air and 700 ft/sec for natural gas. Swages
(reducers) should be used to further reduce the outlet piping
velocity to approximately 200 ft/sec or less to minimize
pressure loss. The formulas for velocity and pipe size are
as follows:
NOTE: To avoid the possibility of excessive noise, vibration,
and damage to the regulator and piping, the outlet velocity
should not exceed 70% of sonic velocity.
Air: 770 ft/sec Natural Gas: 1000 ft/sec
Universal Gas Sizing Equation
520
G T
SIN P
1
[ [
Cg = deg.
Q
3417
C
1
P
1
- P
2
P
1
Simplifies
1.29
Natural Gas at 60 F & 0.6 Sg
Simplifies
1.00
Critical Flow
Q Flow Rate (SCFH)
Cg Gas Sizing Coefcient
P
1
Inlet Pressure (psia)
P Pressure Drop Across Valve ( P = P
1
- P
2
) (psid)
P
2
Outlet Pressure (psia)
C1 Valve Recovery Coefcient (C
1
= Cg/C
v
)
Cv Liquid Sizing Coefcient
G Specic Gravity (0.6 for Natural Gas) (1.0 for Air)
T Gas Temperature (Rankine) (T - 460 + F)
P
A
G
Q = C
v
F
p
P
A
or
P
Allowable
P
A
P
1
- P
2
or
.8 (P
1
- P
v
) } whichever is less
Q Flow gpm (gallons per minute)
Cv Liquid Specic Gravity
Use the minimum inlet and maximum flow conditions for a
given application and solve the equation for Cg. For optimum
performance, select a regulator to operate in the 10-80%
range. A Dresser representative can help you select and
size a Flowgrid

regulator.
748 Q
d
2
P
2
V =
V Velocity in ft/sec
d Internal pipe diameter in inches
Q Flow in MSCFH
P
2
Outlet Pressure (psia)
Mooney Flowgrid Regulator | 9
520
G T
Cg P
1
SIN 3417
C
1
[ [
Q =
P
P
1
deg.
G Liquid Specic Gravity
P
1
Inlet Pressure (psia)
P
2
Outlet Pressure (psia)
Pv Vapor Pressure (psia)
F
P
Piping Swage Factor
Nominal
Size
inches
Stock No. End
Connections
Max
Pressure
(psig)
Nominal
Port Size
Cg C
v
C
1
Face to Face
inches
(metric)
Weight
(valve only)
1 FG11 & 12 NPT/SWE 1480 1 450 13.4 34 7.00 (178) 11 lbs.
1 FG 54** 150 CL FLG 285 1 450 13.4 34 7.25 (184) 14 lbs.
1 FG 55 ** 300 CL FLG 740 1 450 13.4 34 7.75 (197) 16 lbs.
1 FG 56** 600 CL FLG 1480 1 450 13.4 34 8.25 (210) 18 lbs.
1-1/4 FG 13 & 14 NPT/SWE 1480 1 450 13.4 34 7.00 (178) 11 lbs.
1-1/2 FG 47 &48 NPT/SWE 1480 1 480 13.4 36 7.00 (178) 11 lbs.
1 FG 24 NPT 250* 1 428 13.1 32 7.00 (178) 8 lbs.
1-1/4 FG 25 NPT 250* 1 432 13.6 31 7.00 (178) 8 lbs.
1-1/2 FG 26 NPT 250* 1 457 14 32 7.00 (178) 8 lbs
2 x 1 FG 29 & 50 NPT/SWE 1480 1 500 13.4 37 7.00 (178) 14 lbs.
2 x 1 FG 51 150 CL FLG 285 1 500 13.4 37 10.00 (254) 23 lbs.
2 x 1 FG 52 300 CL FLG 740 1 500 13.4 37 10.50 (267) 26 lbs.
2 x 1 FG 53 600 CL FLG 1480 1 500 13.4 37 11.25 (286) 30 lbs.
2 FG 1 & 2 NPT/SWE 1480 2 Std 1130 32 35 8.00 (203) 25 lbs.
2 FG 3 150 CL FLG 285 2 Std 1130 32 32 10.00 (254) 37 lbs.
2 FG 4 300 Cl FLG 740 2 Std 1130 32 35 10.50 (267) 39 lbs.
2 FG 5 600 CL FLG 1480 2 Std 1130 32 35 11.25 (286) 43 lbs.
2 FG 27 & 28 NPT/SWE 1480 2 LP 1420 40 35 8.00 (203) 25 lbs.
2 FG 29 150 CL FLG 285 2 LP 1420 40 35 10.00 (254) 34 lbs.
2 FG 30 300 CL FLG 740 2 LP 1420 40 35 10.50 (267) 37 lbs.
2 FG 31 600 CL FLG 1480 2 LP 1420 40 35 11.25 (286) 40 lbs.
2 FG 82 NPT 250* 2 LP 1600 46 35 8.00 (203) 17 lbs.
2 FG 83 150 CL FLG RF 250* 2 LP 1600 46 35 10.00 (254) 22 lbs.
2 FG 84 150 CL FLG FF 250* 2 LP 1600 46 35 10.00 (254) 22 lbs.
2 x 3 FG 119 150 CL FLG 285 3 1970 56 35 10.00 (254) 78 lbs.
2 x 3 FG 120 300 CL FLG 740 3 1970 56 35 10.50 (267) 82 lbs.
2 x 3 FG 121 600 CL FLG 1480 3 1970 56 35 11.25 (286) 88 lbs.
2 x 3 FG 117 NPT CL 600 1480 3 1970 56 35 8.00 (203) 68 lbs.
2 x 3 FG 118 SWE CL 600 1480 3 1970 56 35 8.00 (203) 68 lbs.
3 FG 16 150 CL FLG 285 3 3450 96 36 11.75 (298) 73 lbs.
3 FG 17 300 CL FLG 740 3 3450 96 36 12.50 (317) 85 lbs.
3 FG 18 600 CL FLG 1480 3 3450 96 36 13.25 (337) 94 lbs.
4 FG 39 150 CL FLG 285 4 6500 172 38 13.88 (352) 103 lbs.
4 FG 40 300 CL FLG 740 4 6500 172 38 14.50 (368) 117 lbs.
4 FG 41 600 CL FLG 1480 4 6500 172 38 15.50 (394) 143 lbs.
6 FG 44 150 CL FLG 285 6 12500 313 40 17.75 (451) 200 lbs.
6 FG 45 300 CL FLG 740 6 12500 313 40 18.62 (473) 240 lbs.
6 FG 46 600 CL FLG 1480 6 12500 313 40 20.00 (508) 330 lbs.
8 FG 72 150 CL FLG 285 8 20200 530 38 21.38 (543) 450 lbs.
8 FG 72 300 CL FLG 740 8 20200 530 38 22.38 (568) 500 lbs.
8 FG 80 600 CL FLG 1480 8 20200 530 38 24.00 (610) 650 lbs.
* Ductile Iron & Aluminum ** Special welded assembly
Single Port Designs
10 | Dresser
Nominal
Size
inches
Stock No. End
Connections
Max
Pressure
(psig)
Nominal
Port Size
Cg C
v
C
1
Face to Face
inches
(metric)
Weight
(valve only)
2 FG 8 150 CL FLG 285 2 Std 1960 56 35 10.00 (254) 52 lbs.
2 FG 9 300 CL FLG 740 2 Std 1960 56 35 10.50 (267) 55 lbs.
2 FG 10 600 CL FLG 1480 2 Std 1960 56 35 11.25 (286) 59 lbs.
2 FG 32 150 CL FLG 285 2 LP 2050 59 35 10.00 (254) 50 lbs.
2 FG 33 300 CL FLG 740 2 LP 2050 59 35 10.50 (267) 52 lbs.
2 FG 34 600 CL FLG 1480 2 LP 2050 59 35 11.25 (286) 54 lbs.
4 FG 21 150 CL FLG 285 3 6700 185 36 13.88 (352) 145 lbs.
4 FG 22 300 CL FLG 740 3 6700 185 36 14.50 (368) 160 lbs.
4 FG 23 600 CL FLG 1480 3 6700 185 36 15.50 (394) 194 lbs.
10 FG 57 150 CL FLG 285 6 22000 550 40 26.50 (673) 590 lbs.
10 FG 58 300 CL FLG 740 6 22000 550 40 27.88 (708) 670 lbs.
10 FG 59 600 CL FLG 1480 6 22000 550 40 29.60 (752) 900 lbs.
12 FG 74 150 CL FLG 285 8 40400 1060 38 29.00 (737) 1097 lbs.
12 FG 75 300 CL FLG 740 8 40400 1060 38 30.50 (775) 1195 lbs.
12 FG 81 600 CL FLG 1480 8 40400 1060 38 32.25 (819) 1383 lbs.
Dual Port Designs
Nominal
Size
inches
Stock No. End
Connections
Max
Pressure
(psig)
Nominal
Port Size
Cg C
v
C
1
Face to Face
inches
(metric)
Weight
(valve only)
2 FG 15 150 CL FLG 285 2 Std 1120 32 35 4.187 (106) 27 lbs.
2 FG 15 300 CL FLG 740 2 Std 1120 32 35 4.187 (106) 27 lbs.
2 FG 15 600 CL FLG 1480 2 Std 1120 32 35 4.187 (106) 27 lbs.
2 FG 35 150 CL FLG 285 2 LP 1300 37 35 4.187 (106) 27 lbs.
2 FG 35 300 CL FLG 740 2 LP 1300 37 35 4.187 (106) 27 lbs.
2 FG 35 600 CL FLG 1480 2 LP 1300 37 35 4.187 (106) 27 lbs.
4 x 3 FG 19 150 CL FLG 285 3 3400 95 36 5.81 (148) 92 lbs.
4 x 3 FG 20 300 CL FLG 740 3 3400 95 36 5.81 (148) 92 lbs.
6 x 4 FG 42 150 CL FLG 285 4 6400 172 37 8.00 (203) 115 lbs.
6 x 4 FG 43 300 CL FLG 740 4 6400 172 37 8.00 (203) 115 lbs.
Flangeless Port Designs
Nominal
Size
inches
Stock No. End
Connections
Max
Pressure
(psig)
Nominal
Port Size
Cg C
v
C
1
Face to Face
inches
(metric)
Weight
(valve only)
2 FG 100 150 CL FLG 285 2 LP 1420 40 35 3.03 (77) 29 lbs.
2 FG 101 300 CL FLG 740 2 LP 1420 40 35 3.03 (77) 29 lbs.
2 FG 102 600 CL FLG 1480 2 LP 1420 40 35 3.41 (87) 29 lbs.
3 FG 103 150 CL FLG 285 3 3240 95 36 3.72 (94) 60 lbs.
3 FG 104 300 CL FLG 740 3 3240 95 36 3.72 (94) 60 lbs.
4 FG 106 150 CL FLG 285 4 5800 168 35 4.50 (114) 85 lbs.
4 FG 107 300 CL FLG 740 4 5800 168 35 4.50 (114) 85 lbs.
Type-A Flangeless Port Designs*
* Same face-to-face dimensions as American Meter Axial

Flow Valves.
Mooney Flowgrid Regulator | 11
About Dresser, Inc.
Dresser, Inc. is a leader in providing highly engineered
infrastructure products for the global energy industry.
The company has leading positions in a broad portfolio
of products, including valves, actuators, meters,
switches, regulators, piping products, natural gas-
fueled engines, retail fuel dispensers and associated
retail point-of-sale systems, and air and gas handling
equipment. Leading brand names within the Dresser
portfolio include Dresser Wayne

retail fueling systems,


Waukesha

natural gas-fired engines, Masoneilan


control valves, Consolidated

pressure relief valves,


and Roots

blowers. It has manufacturing and cus-


tomer service facilities located strategically worldwide
and a sales presence in more than 100 countries.
About Dresser

Products
Dresser brand products are highly engineered, technically
superior and are designed to help global customers meet and
exceed requirements for mission critical energy applications.
The information presented in this brochure is for informational purposes only.
For actual design assistance please visit our website at www.dresser.com/mooneyregulators
or see your local representative.
www.dresser.com
Dresser, Inc.
2822 S. 1030 W.
Salt Lake City, Utah 84119
Phone: 801.487.2225 Fax: 801.487.2587
www.dresser.com/mooney
2010 Dresser, Inc.
FlowMax and Mooney are registered trademarks of Dresser, Inc.
Flowgrid Regulator
7.10

You might also like