J

N
T
U
W
O
R
L
D
Code No: A109211002 R09 Set No. 2
II B.Tech I Semester Examinations,November 2010
SWITCHING THEORY AND LOGIC DESIGN
Common to Instrumentation And Control Engineering, Electronics And
Computer Engineering, Electronics And Instrumentation Engineering
Time: 3 hours Max Marks: 75
Answer any FIVE Questions
All Questions carry equal marks

1. (a) Explain the procedure to obtain the Complement of a Function. Explain how
it diers from Dual of a function.
(b) Determine the complements of the following function.
i. AB+ CD(AB

+CD)
ii. AB(BC

+BC)(AC

+AB)
iii. A + B[A +(B+C)

D]
iv. AB + A

+ A

BC [8+7]
2. (a) Design a modulo-9 shift counter using T ip ops. Explain the design proce-
dure with state diagram, state table, excitation table.
(b) Construct a T-Latch and explain its operation. [10+5]
3. (a) i. Convert (1596.675)
10
to hexadecimal
ii. Convert (11110.1011)
2
to decimal
iii. Convert (10110001.01101001)
2
to octal
iv. Convert (235.0657)
8
to Binary
(b) Obtain the 1s complement and 2s complement of the binary numbers
i. 1011011
ii. 0110101
iii. 10110
iv. 00110 [8+7]
4. Minimize the following incompletely specied machine using Merger Table method.
[15]
PS NS,Z
X = 0 X = 1
A E,0 B,0
B F,0 A,0
C E,- C,0
D F,1 D,0
E C,1 C,0
F D,- B,0
5. (a) Design a logic circuit which accepts a 4 Binary input and converts it into BCD
number. Draw the logic circuit with AND gates and OR gates.
1
www.jntuworld.com
www.jntuworld.com
J
N
T
U
W
O
R
L
D
Code No: A109211002 R09 Set No. 2
(b) List down the Design procedure of combinational logic circuits. [8+7]
6. (a) Write short notes on ASM chart. Give the dierent boxes used in the ASM
chart. Explain them with examples.
(b) Write the salient features of ASM chart. [8+7]
7. List the PLA Programming table for OCTAL to BCD converter. Implement the
function in a ROM and PLA. Compare both the design and justify which is the
most economical. [15]
8. Design a circuit which takes 3 inputs A, B, C. The circuit should be designed in
such a way that it has 8 outputs connected to LED. The LED should glow if its
input is HIGH. The circuit should be designed in such a way that the one LED
glows at a time based on the Input combinations. The outputs of the circuit should
correspond to the minterms of the inputs. [15]

2
www.jntuworld.com
www.jntuworld.com
J
N
T
U
W
O
R
L
D
Code No: A109211002 R09 Set No. 4
II B.Tech I Semester Examinations,November 2010
SWITCHING THEORY AND LOGIC DESIGN
Common to Instrumentation And Control Engineering, Electronics And
Computer Engineering, Electronics And Instrumentation Engineering
Time: 3 hours Max Marks: 75
Answer any FIVE Questions
All Questions carry equal marks

1. What are the conditions for the two machines are to be equivalent? For the machine
given below, nd the equivalence partition and a corresponding reduced machine
in standard form. [15]
PS NS,Z
X=0 X=1
A F,0 B,1
B G,0 A,1
C B,0 C,1
D C,0 B,1
E D,0 A,1
F E,1 F,1
G E,1 G,1
2. Reduce the given function using Quine McC lusky method
F(A,B,C,D,E,F)=m (0,1,2,4,6,9,12,16,21,25,29,32,37,41,43,45,56,58,62,63) [15]
3. Explain the construction and working of SR ip Flop for dierent input conditions.
Explain in detail the output conditions of SR ip op if S=R=1.How the circuit is
modied to avoid this conditions. [15]
4. (a) Prove the following identity
XY + X

+YZ = XY +X

+X

Z
(b) Dene Switching functions. Consider a 3 variable switching function and
create a Truth table for all possible values of the input.
(c) Consider 2 functions, f = x

y +xyz

& g = xy

+ xz. For all possible values of

. [4+4+7]
5. Design a sequential logic circuit of a 4 bit counter to start counting from 0000 to
1000 and this process should go on. Draw the ASM chart and design the Data
processing unit and the control unit. [15]
6. (a) Design a full adder circuit using 2 half adders.
(b) Design a 4 bit Parallel adder using full adders. [8+7]
7. Implement the following Boolean functions using ROM and PAL.
F1(x,y,z) = (0,1,5,7)
F2(x,y,z) = (1,2,3,6,7)
3
www.jntuworld.com
www.jntuworld.com
J
N
T
U
W
O
R
L
D
Code No: A109211002 R09 Set No. 4
F3(x,y,z) = (3,5,6,7)
F4(x,y,z) = (0,2,3,4,6) [15]
8. (a) Explain the procedure for converting Gray code to Binary code with an
example.
(b) Explain the procedure for converting Binary code to Gray code with an
example. [8+7]

4
www.jntuworld.com
www.jntuworld.com
J
N
T
U
W
O
R
L
D
Code No: A109211002 R09 Set No. 1
II B.Tech I Semester Examinations,November 2010
SWITCHING THEORY AND LOGIC DESIGN
Common to Instrumentation And Control Engineering, Electronics And
Computer Engineering, Electronics And Instrumentation Engineering
Time: 3 hours Max Marks: 75
Answer any FIVE Questions
All Questions carry equal marks

1. Draw the ASM for the following sequence.
0000 0001 0010 0011 0100 0000 and continues.
Design the data processing unit and control unit to implement the above mentioned
design. [15]
2. (a) Simplify using Boolean postulates and verify using K-map the following
i. (x+y

+xy

)(xy+x

z+yz)
ii. (A+B)(A

+C)(B+C)
(b) Simplify the following function using K-map
F = M(1,5,7,9,11,13) [11+4]
3. (a) Dene Truth table with examples. Dene Huntington Postulates.
(b) Implement the following Boolean functions as logic circuits
F1 = (AB + C

D)

(A

B xor D)

(C

D)

F2 = (A + B[A+(B+C)

D]

) [8+7]
4. (a) Explain how decoder acts as a demultiplexer.
(b) Realize the logic function using 8:1 multiplexer
F(w,x,y,z) = m(0,1,3,5,6,15) [8+7]
5. For the machine shown, nd the equivalent partition and a corresponding reduced
machine in standard form. [15]
PS NS,Z
X = 0 X = 1
A F,0 B,1
B G,0 A,1
C B,0 C,1
D C,0 B,1
E D,0 A,1
F E,1 F,1
G E,1 G,1
6. (a) Solve for X
i. (F3A7C2)
16
= (X)
10
ii. (2AC5)
16
= (10949)
X
iii. (0.93)
10
= (X)
8
5
www.jntuworld.com
www.jntuworld.com
J
N
T
U
W
O
R
L
D
Code No: A109211002 R09 Set No. 1
iv. (4057.06)
8
= (X)
10
(b) The message given below has been coded in the Hamming code and transmit-
ted through a noisy channel. Decode the message assuming that at most a
single error has occurred in each code word of 8 bits.
1 0 0 1 0 0 1 0 1 1 1 0 0 1 1 1 1 0 1 1 0 0 0 1 1 0 1 1 [8+7]
7. A combinational logic circuit is dened by the following functions.
F1(w,x,y,z) = (1,3,12)
F2(w,x,y,z) = (1,2,5,7,8,9,10)
F3(w,x,y,z) = (0,1,2,4,6,8,9,12,15)
F4(w,x,y,z) = (1,2,3,5,7,9,12,14,15)
Implement the circuit using PLA. [15]
8. A long sequence of pulses enters a 2 input, 2 output synchronous sequential circuit,
which is required to produce an output pulse y =1 whenever the sequence 1010
occurs. Overlapping sequences are accepted.
(a) Draw the state diagram.
(b) Select an assignment and show the excitation and output tables.
(c) Write the excitation table for JK ip op and draw the corresponding logic
diagram. [15]

6
www.jntuworld.com
www.jntuworld.com
J
N
T
U
W
O
R
L
D
Code No: A109211002 R09 Set No. 3
II B.Tech I Semester Examinations,November 2010
SWITCHING THEORY AND LOGIC DESIGN
Common to Instrumentation And Control Engineering, Electronics And
Computer Engineering, Electronics And Instrumentation Engineering
Time: 3 hours Max Marks: 75
Answer any FIVE Questions
All Questions carry equal marks

1. (a) Dierentiate Hexadecimal codes and Alpha numeric codes
(b) Write Gray codes for the following decimal numbers
i. 1000
ii. 724
iii. 83
iv. 37
[8+7]
2. Design a combinational logic circuit to convert the input Gray code into equivalent
BCD code using a Multiplexer. Write the truth table to indicate the conversion.
Draw the logic diagram. [15]
3. (a) Obtain the ASM chart for the following state transition. State T1 starts and
then goes to state T2 when AB = 00, then goes to state T3 when AB = 01
and then goes to state T1 when AB = 10, otherwise to state T3.
(b) Draw an ASM chart for a DATA ip op. [8+7]
4. Minimize the following incompletely specied machine using Merger Graph method.
[15]
PS NS,Z
I1 I2 I3 I4
A - C,1 E,1 B,1
B E,0 - - -
C F,0 F,1 - -
D - - B,1 -
E - F,0 A,0 D,1
F C,0 - B,0 C,1
5. (a) Dene the Distributive law and Idempotence law with examples
(b) Prove that
i. AB + A

C = (A +C)(A

+B)
ii. (A+B) (A

+C)(B+C) = (A+B)(A

+C) [8+7]
6. (a) Design a clocked SR ip op. Explain its operation with the help of charac-
teristic table and characteristic equation. Give the symbol of edge triggered
SR ipop.
7
www.jntuworld.com
www.jntuworld.com
J
N
T
U
W
O
R
L
D
Code No: A109211002 R09 Set No. 3
(b) Explain the operation of JK ipop with the help of input output waveforms.
[8+7]
7. A digital system has 4 inputs W, X,Y, Z. If any three, or all four inputs are HIGH
The output F must go HIGH. If only 2 inputs are HIGH, then the output will take
the value of Z. If only one, or none, of the inputs is HIGH the output must be
LOW. Design the circuit. [15]
8. Design a 4 input priority encoder in a ROM and PAL. [15]

8
www.jntuworld.com
www.jntuworld.com