BNBC Part 05 - Building Materials

5-i Vol.
2
TABLE OF CONTENTS

PART 5 BUILDING MATERIALS
Chapter 1 SCOPE AND DEFINITIONS
1.1 SCOPE 5-1
1.2 TERMINOLOGY 5-1
Chapter 2 BUILDING MATERIALS
2.1 GENERAL 5-3
2.2 MASONRY 5-4
2.3 CEMENT AND CONCRETE 5-10
2.4 PRE-STRESSED CONCRETE 5-17
2.5 BUILDING LIMES 5-18
2.6 GYPSUM BASED MATERIALS AND PLASTER 5-19
2.7 FLOORING MATERIALS 5-20
2.8 STEEL 5-24
2.9 TIMBER & WOOD PRODUCTS 5-39
2.10 DOORS, WINDOWS AND VENTILATORS 5-42
2.11 ALUMINIUM AND ALUMINIUM ALLOYS 5-45
2.12 BUILDERS HARDWARE 5-47
2.13 ROOF COVERINGS 5-49
2.14 PAINTS AND VARNISHES 5-54
2.15 SANITARY APPLIANCES AND WATER FITTINGS 5-60
2.16 MISCELLANEOUS MATERIALS 5-71
2.17 CGI SHEET ROOFING AND WALLING 5-88

PERSONAL COLLECTION OF
ENGR. PRANOY BARUA
BANGLADESH STEEL RE-ROLLING MILLS LTD
[email protected]

Part 5
Building Materials 5-1
Chapter 1
SCOPE AND DEFINITIONS
1.1 SCOPE
This part specifies the minimum requirements of materials to be complied with in buildings and works under the
provisions of the Code.
For each of the building materials the applicable standard specifications and test methods are listed. All materials
shall conform to these standards.
The list of standards given in this part of the Code would be augmented from time to time by amendments,
revisions and additions of which the Authority shall take cognizance. The latest version of a specification shall, as
far as practicable, be applied in order to fulfil the requirements of this part.
In view of the limited number of Bangladesh Standards for building materials available at the present time, a
number of standards of other countries have been referenced in this Code as applicable standards. As more
Bangladesh Standards regarding building materials become available, these after adoption by amendment of the
Code, shall supplement and/or replace the relevant standards listed in this part.
1.2 TERMINOLOGY
This section provides an alphabetical list of the terms used in and applicable to this part of the Code. In case of
any conflict or contradiction between a definition given in this section and that in Part 1, the meaning provided in
this part shall govern for interpretation of the provisions of this part.
Actual dimensions: Measured dimensions of a designated item.
Admixture: Material other than water, aggregate, or hydraulic cement used as an ingredient of concrete and
added to concrete before or during its mixing to modify its properties.
Aggregate, Lightweight: Aggregate with a dry, loose weight of 11.25 kN/m
3
.
Aggregate: Granular material, such as sand, gravel, crushed stone, crushed brick and iron blast-furnace slag, when
used with a cementing medium forms a hydraulic cement concrete or mortar.
Concrete: A mixture of Portland cement or any other hydraulic cement, fine aggregate, coarse aggregate and
water, with or without admixtures.
Deformed Reinforcement: Deformed reinforcing bars, bar and rod mats, deformed wire, welded smooth wire
fabric and welded deformed wire fabric.
Fibreboard: A fibre-felted, homogenous panel made from lignocellulosic fibres (usually wood or cane) and having
a unit weight of less than 5 kN/m
3
but more than 1.6 kN/m
3
.
Grouted Hollow-unit Masonry: Form of grouted masonry construction in which certain designated cells of hollow
units are continuously filled with grout.
Hardboard: A fibre-felted homogenous panel made from lignocellulosic fibres consolidated under heat and
pressure in a hot press to a density not less than 4.9 kN/m
3
.
HOLLOW MASONRY Unit: A masonry unit whose net cross-sectional area in every plane parallel to the bearing
surface is less than 75 per cent of the gross cross-sectional area in the same plane.
Masonry Unit: Brick, tile, stone, glass-block or concrete-block used in masonry constructions.
Nominal dimensions: Nominal dimensions of masonry units are equal to their specified dimensions plus the
thickness of the joint with which the unit is laid.
Part 5
Building Materials

5-2 Vol. 1
Particle board: A manufactured panel product consisting of particles of wood or combinations of wood
particles and wood fibres cemented together with synthetic resins or other suitable bonding system by
an appropriate bonding process.
Plain Concrete: Concrete that does not conform to the definition of reinforced concrete.
Plain ReinforcemenT: Reinforcement that does not conform to definition of deformed reinforcement.
Plywood: A built-up panel of laminated veneers
Precast Concrete: Plain or reinforced concrete element cast separately before they are fixed in position.
Prestressed Concrete: Reinforced concrete in which internal stresses have been introduced to reduce
potential tensile stresses in concrete resulting from loads.
Reinforced Concrete: Concrete containing adequate reinforcement, prestressed or non-prestressed, and
designed on the assumption that the two materials act together in resisting forces.
Reinforced Masonry: Form of masonry construction in which reinforcement acting in conjunction with
the masonry is used to resist designed forces.
Reinforcement: Reinforcing bars, plain or deformed, excluding prestressing tendons, bar and rod mats,
welded smooth wire fabric and welded deformed wire fabric used in concrete.
Solid Masonry Unit: A masonry unit whose net cross-sectional area in every plane parallel to the bearing
surface is 75 per cent or more of the gross cross-sectional area in the same plane.
Spiral Reinforcement: Continuously wound reinforcement in the form of a cylindrical helix.
Stirrup: Reinforcement used to resist shear and torsion stresses in structural member; typically bars,
wires, or welded wire fabric (smooth or deformed) bent into L, U or rectangular shapes and located
perpendicular to or at an angle to longitudinal reinforcement. (The term "Stirrup" is usually applied to
lateral reinforcement in flexural members and the term "ties" to those in compression members).
Structural GLUED LAMINATED Timber: Any member comprising an assembly of laminations of lumber in
which the grain of all laminations is approximately parallel longitudinally in which the laminations are
bonded with adhesives.
Tendon: Steel element such as wire, cable, bar, rod or strand, or a bundle of such elements, used to
impart prestress to concrete.
Tie: A loop of reinforcing bar or wire enclosing longitudinal reinforcement.
Yield Strength: The stress at which plastic deformation takes place under constant or reduced load.
Part 5
Building Materials 5-3
Chapter 2
BUILDING MATERIALS
2.1 GENERAL
Materials used for the construction of buildings shall conform to standard specifications listed in this part of the
Code. Any deviation from the type design or architectural detail from those specified in these standards may be
accepted by the Building Official as long as the materials standards specified therein are conformed with.
2.1.1 New or Alternative Materials
The provisions of this part are not intended to prevent the use of any new and alternative materials. Any such
material may be approved provided it is shown to be satisfactory for the purpose intended and at least the
equivalent of that required in this part in quality, strength, effectiveness, fire resistivity, durability, safety,
maintenance and compatibility.
Approval in writing shall be obtained by the owner or his agent before any new, alternative or equivalent
materials are used. The Building Official shall base such approval on the principle set forth in the previous
paragraph and shall require that specified tests be made (Sec 2.1.4) or sufficient evidence or proof be submitted,
at the expense of the owner or his agent, to substantiate any claim for the proposed material.
2.1.2 Used Materials
The provisions of this partdo not preclude the use of used or reclaimed materials provided such materials meet
the applicable requirements as for new materials for their intended use.
2.1.3 Storage of Materials
All building materials shall be stored at the building site(s) in such a way as to prevent deterioration or the loss or
impairment of their structural and other essential properties (See Part 7, Construction Practices and Safety).
2.1.4 Methods of Test
Every test of material required in this part, or by the Building Official, for the control of quality and for the
fulfillment of design and specification requirements, shall be carried out in accordance with a standard method of
test issued by the Bangladesh Standards and Testing Institution. In the absence of Bangladesh Standards, the
Building Official shall determine the test procedures. Laboratory tests shall be conducted by recognized
laboratories acceptable to the Building Official.
If, in the opinion of the Building Official, there is insufficient evidence of compliance with any of the provisions of
the Code or there is evidence that any material or construction does not conform to the requirements of this
Code, the Building Official may require tests to be performed as proof of compliance. The cost of any such test
shall be borne by the owner.
The manufacturer or supplier shall satisfy himself that the materials conform to the relevant standards and if
requested shall furnish a certificate or guarantee to this effect.
Part 5
Building Materials

5-4 Vol. 2
2.2 MASONRY
2.2.1 Aggregates
Aggregates for masonry shall conform to the standards listed as follows: ASTM C144 - 04, Aggregates for Masonry
Mortar; ASTM C404 -07, Aggregates for Masonry Grout; ASTM C331 - 05, Lightweight Aggregates for Concrete
Masonry Units (the applicable standards for masonry are listed at the end of this section).
2.2.2 Cement
Cement for masonry shall conform to the standards listed as follows: BDS EN 197-1: 2003Cement Part-1
Composition, specifications and conformity criteria for common cements; or ASTM C150 / C150M - 09, Portland
Cement; ASTM C91 - 05, Masonry Cement; ASTM C595 / C595M - 10, Blended Hydraulic Cements.
2.2.3 Lime
Limes for masonry shall conform to the standards listed as follows: ASTM C5 - 03, Quicklime for Structural
Purposes; ASTM C207 - 06, Hydrated Lime for Masonry Purposes.
2.2.4 Masonry Units
a) Clay : Masonry units of clay (or shale) shall conform to the standards listed as follows: BDS 208: 1980,
Common Building Clay Bricks (First Revision); BDS 1249:1989, Acid Resistant Bricks; BDS 1250: 1989,
Burnt Clay Facing Bricks; BDS 1263: 1990, Burnt Clay Hollow Bricks for Walls and Partitions; BDS 1264 :
1990, Glossary of terms relating to structural clay products; BDS 1432 : 1993, Burnt clay perforated
building bricks; BDS 1803 : 2008, Specification for Hollow Clay Bricks and Blocks; ASTM C34 09,
Structural Clay Load-Bearing Wall Tile; ASTM C212 00(2006), Structural Clay Facing Tile; ASTM C56 09
Structural Clay Non-Load-Bearing Tile; and IS 7556-1975 Burnt Clay Jallies.
b) Concrete: Concrete masonry units shall conform to the standards listed as follows:
BDS EN 771-3: 2009
Specification for masonry units Part: 3 Aggregate concrete masonry
units (dense and lightweight aggregates)
BDS EN 772-1: 2009
Methods of test for masonry units Part 1: Determination of
compressive strength
BDS EN 772-2: 2009
Methods of test for masonry units Part 2: Determination of percentage
area of voids in masonry units (by paper indentation)
BDS EN 772-6: 2009
Methods of test for masonry units Part 6: Determination of bending
tensile strength of aggregate concrete masonry units
BDS EN 772-11: 2009
Methods of test for masonry units Part 11: Determination of water
absorption of aggregate concrete, autoclaved aerated concrete,
manufactured stone and natural stone masonry units due to capillary
action and the initial rate of water absorption of clay masonry units
BDS EN 772-13: 2009
Methods of test for masonry units Part 13: Determination of net and
gross dry density of masonry units (except for natural stone)
BDS EN 772-14: 2009
Methods of test for masonry units Part 14: Determination of moisture
movement of aggregate concrete and manufactured stone masonry units
BDS EN 772-16: 2009
Methods of test for masonry units Part 16: Determination of
dimensions
BDS EN 772-20: 2009
Methods of test for masonry units Part 20: Determination of flatness of
faces of masonry units
Building Materials Chapter 2

Bangladesh National Building Code 2012 5-5
BDS EN 1052-3: 2009 Methods of test for masonry Part 3: Determination of initial shear strength
BDS EN 1745: 2009 Masonry and masonry products Methods for
determining design thermal values
ASTM C90 09 Hollow Load-Bearing Concrete Masonry Units;
ASTM C129 06 Non-Load Bearing Units;
ASTM C90 09 Solid Load-Bearing Units;
ASTM C55 09 Concrete Building Bricks.
c) Others
I. Calcium Silicate: Calcium Silicate Face Brick (Sand-Lime Brick) shall conform to
ASTM C73 05 standardspecification.
II. Glazed Masonry Units: Glazed Masonry building units shall conform to the
standards listed as follows: ASTM C126 09, Ceramic-Glazed Structural Clay
Facing Tile, Facing Brick, and Solid Masonry Units; or ASTM C744 09, Prefaced
Concrete and Calcium Silicate Masonry Units.
III. Glass Block: Glass block may be solid or hollow and contain inserts; all mortar
contact surfaces shall be treated to ensure adhesion between mortar and glass.
IV. Unburnt Clay Masonry Units: Masonry of unburnt clay units including cement
stabilized and lime stabilized blocks shall not be used, in any building more than
one storey in height.
V. Architectural Terra Cotta: All architectural terra cotta units shall be formed with
a strong homogeneous body of hard-burnt weather-resistant clay which gives
off a sharp metallic ring when struck. All units shall be formed to engage
securely with and anchor to the structural frame or masonry wall.
VI. Natural Stone: Natural stone for masonry shall be sound and free from loose
friable inclusions. Natural stone shall have the strength and fire resistance
required for the intended use.
VII. Cast Stone: All cast stone shall be fabricated of concrete or other approved
materials of required strength, durability and fire resistance for the intended
use and shall be reinforced where necessary.
VIII. AAC Masonry: AAC (autoclaved Aerated Concrete) masonry units shall conform
to ASTM C1386 07 for the strength class specified.
IX. Ceramic tile: Ceramic tile shall be as defined in, and shall conform to the
requirements of ANSI A137.1:2008
X. Second Hand Units: Second hand masonry units shall not be used unless the
units conform to the requirements for new units. The units shall be of whole,
sound material and be free form cracks and other defects that would interfere
with proper laying or use. All old mortar shall be cleaned from the units before
reuse.
2.2.5 Mortar
Mortar shall consist of a mixture of cementitious material and aggregates to which sufficient water and approved
additives, if any, have been added to achieve a workable, plastic consistency. Cementitious materials for mortar
Part 5
Building Materials

5-6 Vol. 2
shall be one or more of the following: lime, masonry cement, Portland cement and mortar cement. Mortar for
masonry construction other than the installation of ceramic tile shall conform to the requirements of BDS 1303 :
1990 Chemical resistant mortars; BDS 1304:1990 Methods of test for chemical resistant mortars; ASTM C270
08a, Mortar for Unit Masonry.
2.2.6 Grout
Grout shall consist of a mixture of cementitious materials and aggregates to which water has been added such
that the mixture will flow without segregation of the constituents. Cementitious materials for grout shall be one
or both of the following: Lime and Portland cement. Grout shall have a minimum compressive strength of 13 Mpa.
Grout used in reinforced and nonreinforced masonry construction shall conform to the requirements of ASTM
C476 09, Grout for Masonry.
2.2.7 Mortar for Ceramic Wall and Floor Tile
Portland cement mortars for installing ceramic wall and floor tile shall comply with ANSI A 108.1-2005 listed in Sec
2.2.11 and be of the composition specified in Table 5.2.1.
2.2.7.1 Dry-set 6eveling cement mortars.
Premixed prepared 6eveling cement mortars, which require only the addition of water and are used in the
installation of ceramic tile, shall comply with ANSI A118.1-2009. The shear bond strength for tile set in such
mortar shall be as required in accordance with ANSI A118.1-2009. Tile set in dry-set Portland cement mortar shall
be installed in accordance with ANSI A108.5 -1999 (R2005).
2.2.7.2 Latex-modified 6eveling cement mortar.
Latex-modified 6eveling cement thin-set mortars in which latex is added to dry-set mortar as a replacement for all
or part of the gauging water that are used for the installation of ceramic tile shall comply with ANSI A118.4-2009.
Tile set in latex-modified 6eveling cement shall be installed in accordance with ANSI A108.5-2009.
2.2.7.3 Epoxy mortar.
Ceramic tile set and grouted with chemical-resistant epoxy shall comply with ANSI A118.3-2009. Tile set and
grouted with epoxy shall be installed in accordance with ANSI A108.6-2009.
2.2.7.4 Furan mortar and grout.
Chemical-resistant furan mortar and grout that are used to install ceramic tile shall comply with ANSI A118.5-
2009. Tile set and grouted with furan shall be installed in accordance with ANSI A108.8-2009.
2.2.7.5 Modified epoxy-emulsion mortar and grout.
Modified epoxy-emulsion mortar and grout that are used to install ceramic tile shall comply with ANSI A118.8-
2009. Tile set and grouted with modified epoxy-emulsion mortar and grout shall be installed in accordance with
ANSI A108.9-2009.
2.2.7.6 Organic adhesives.
Water-resistant organic adhesives used for the installation of ceramic tile shall comply with ANSI A136.1-2009.
The shear bond strength after water immersion shall not be less than 40 psi (275 kPa) for Type I adhesive and not
less than 20 psi (138 kPa) for Type II adhesive when tested in accordance with ANSI A136.1-2009. Tile set in
organic adhesives shall be installed in accordance with ANSI A108.4-2009.

2.2.7.7 Portland cement grouts.
Portland cement grouts used for the installation of ceramic tile shall comply with ANSI A118.6-2009. Portland
cement grouts for tile work shall be installed in accordance with ANSI A108.10-2009.
2.2.7.8 Mortar for AAC masonry.
Thin-bed mortar for AAC masonry shall comply with Article 2.1 C.1 of TMS 602/ACI 530.1/ASCE 6. Mortar used for
the leveling courses of AAC masonry shall comply with Article 2.1 C.2 of TMS 602/ACI 530.1/ASCE 6.
Table 5.2.1: Ceramic Tile Mortar Compositions

Walls
Scratch coat 1 cement;
1
5
hydrated lime; *
4 dry or 5 damp sand
Setting bed and 7eveling coat 1 cement;

1
2
hydrated lime;
5 damp sand to 1 cement;
1 hydrated lime; 7 damp sand
Floors Setting bed
1 cement;
10
1
hydrated lime;
5 dry or 6 damp sand; or 1
cement; 5 dry or 6 damp sand
Ceilings Scratch coat and sand bed 1 cement;

1
2
hydrated lime;

2
1
2
dry sand or 3 damp sand
Note : * Lime may be excluded from the mortar if trial mixes indicate that the desired
workability and performance are achieved without lime.
2.2.8 Metal Ties and Anchors
Metal ties and anchors shall conform to the standards listed as follows: ASTM A82 / A82M 07, Wire Anchor and
Ties; and ASTM A1008 / A1008M 10, Sheet Metal Anchors and Ties.
2.2.9 Reinforcement
Reinforcement in masonry shall conform to the standards listed as follows: ASTM A82 / A82M 07, Cold Drawn
Steel Wire for Concrete Reinforcement; ASTM A615 / A615M 09b, Deformed and Plain Billet Steel Bars; ASTM
A996 / A996M 09b, Rail-Steel Deformed and Plain Bars; ASTM A996 / A996M 09b, Axle-Steel Deformed and
Plain Bars; ASTM A706 / A706M 09b, Low-Alloy Steel Deformed Bars; ASTM A767 / A767M 09, Zinc-Coated
(Galvanized) Steel Bars; and ASTM A775 / A775M 07b, Epoxy Coated Reinforcing Steel Bars.
2.2.10 Water
Water used in mortar or grout shall be clean and free of deleterious amounts of acid, alkalis or organic material or
other harmful substances.
2.2.11 Applicable Standards for Masonry
The applicable standards for Masonry are listed below:
BDS EN 197-1:2003
(Reaffirmed 2010)
Cement Part-1 Composition, specifications and conformity
criteria for common cements.
BDS 208 : 2009 Specification for Common Building clay bricks (Third
revision)Specifies the dimensions, quality & strength of common
burnt clay bricks, methods of sampling, testing etc.
BDS 238 Fireclay refractory bricks and shapes for general purposes. This
Standard specifies the requirements for fireclay refractory bricks
Part 5
Building Materials

5-8 Vol. 2
and shapes meant for general purpose; the products are
classified in four grades according to the duty for which they are
suitable.
BDS 1249 : 1989 Acid resistant bricks. It specifies the requirements for acid-
resistant bricks, dimensions, tolerances, test etc.
BDS 1250 : 1990 Burnt clay facing bricks. It specifies the dimensions, quality &
strength of burnt clay facing bricks used in building & other
structure, physical requirements etc.
BDS 1263 : 1990 Burnt Clay hollow bricks for walls & partitions it covers the
dimensions, quality & strength for hollow bricks made from
burnt clay & having perforations through & at right angle to the
bearing surface tests.
BDS 1264 : 1990 Glossary of terms relating to structural clay products. It covers
the definition of common terms applicable to structural clay
products, used in building & civil engineering works.
BDS 1432 : 1993 Burnt clay perforated building bricks. Specifies the requirements
in regard to dimensions, perforations, quality, strength and also
for quality of surface in case of special grade for facing bricks of
perforated burnt clay building bricks for use in walls and
partitions.
BDS 1433 : 1993 Dimensions quantities in general construction work. Specifies
the various dimensional values in S. I units used in general
construction work.
BDS 1803 : 2008 Specification for Hollow Clay Bricks and Blocks
BDS EN 1338: 2009
Concrete paving blocks Requirements and test methods
BDS EN 1339:2009
Concrete paving flags Requirements and test methods
BDS EN 1340:2009
Concrete kerb units Requirements and test methods
BDS EN 13369: 2009 Common rules for precast concrete products
BDS EN 771-3: 2009 Specification for masonry unitsPart: 3 Aggregate concrete
masonry units (dense and lightweight aggregates)
BDS EN 772-1: 2009 Methods of test for masonry units Part 1: Determination of
compressive strength
percentage area of voids in masonry units (by paper indentation)
bending tensile strength of aggregate concrete masonry units

water absorption of aggregate concrete, autoclaved aerated
concrete, manufactured stone and natural stone masonry units
due to capillary action and the initial rate of water absorption of
clay masonry units
net and gross dry density of masonry units (except for natural
stone)
moisture movement of aggregate concrete and manufactured
stone masonry units
dimensions
flatness of faces of masonry units
BDS EN 1052-3: 2009 Methods of test for masonry Part 3: Determination of initial
shear strength
BDS EN 1745: 2009 Masonry and masonry products Methods for determining
design thermal values
ANSI A108.1A2009 Installation of Ceramic Tile in the Wet-set Method, with Portland
Cement Mortar
ANSI A108.1B2009 Installation of Ceramic Tile, quarry Tile on a Cured Portland
Cement Mortar Setting Bed with Dry-set or Latex-portland
Mortar
ANSI A108.1-2009 Specifications for the Installation of Ceramic Tile with Portland
Cement Mortar;
ASTM A82 / A82M - 07 Specification for Steel Wire, Plain, for Concrete Reinforcement
ASTM A1008 / A1008M -
10
Standard Specification for Steel, Sheet, Cold-Rolled, Carbon,
Structural, High-Strength Low-Alloy, High-Strength Low-Alloy
with Improved Formability, Solution Hardened, and Bake
Hardenable
ASTM A615 / A615M - 09b Standard Specification for Deformed and Plain Carbon-Steel Bars
for Concrete Reinforcement
ASTM A996 / A996M - 09b Standard Specification for Rail-Steel and Axle-Steel Deformed
Bars for Concrete Reinforcement
ASTM A996 / A996M - 09b Standard Specification for Rail-Steel and Axle-Steel Deformed
Part 5
Building Materials

5-10 Vol. 2
ASTM A706 / A706M - 09b Standard Specification for Low-Alloy Steel Deformed and Plain
ASTM A183 - 03(2009) Standard Specification for Carbon Steel Track Bolts and Nuts
ASTM A775 / A775M - 07b Standard Specification for Epoxy-Coated Steel Reinforcing Bars
ASTM C5-03 Standard Specification for Quicklime for Structural Purposes
ASTM C34 - 09 Standard Specification for Structural Clay Load-Bearing Wall Tile
ASTM C55 - 09 Standard Specification for Concrete Building Brick
ASTM C56 - 09 Standard Specification for Structural Clay Non load bearing Tile
ASTM C73 - 05 Standard Specification for Calcium Silicate Brick (Sand-Lime
Brick)
ASTM C90 - 09 Standard Specification for Load bearing Concrete Masonry Units
ASTM C91 - 05 Standard Specification for Masonry Cement
ASTM C126 - 09 Standard Specification for Ceramic Glazed Structural Clay Facing
Tile, Facing Brick, and Solid Masonry Units
ASTM C129 - 06 Standard Specification for Non-load bearing Concrete Masonry
Units
ASTM C144 - 04 Standard Specification for Aggregate for Masonry Mortar
ASTM C90 - 09 Standard Specification for Load bearing Concrete Masonry Units
ASTM C150 / C150M - 09 Standard Specification for Portland Cement
ASTM C207 - 06 Standard Specification for Hydrated Lime for Masonry Purposes
ASTM C212 - 00(2006) Standard Specification for Structural Clay Facing Tile
ASTM C270 - 08a Standard Specification for Mortar for Unit Masonry
ASTM C331 - 05 Standard Specification for Lightweight Aggregates for Concrete
Masonry Units
ASTM C404 - 07 Standard Specification for Aggregates for Masonry Grout
ASTM C476 - 09 Standard Specification for Grout for Masonry
ASTM C595 / C595M - 10 Standard Specification for Blended Hydraulic Cements
ASTM C744 - 09 Standard Specification for Prefaced Concrete and Calcium

Silicate Masonry Units
2.3 CEMENT AND CONCRETE
2.3.1 General
Materials used to produce concrete and admixtures for concrete shall comply with the requirements of this
section and those of Chapter 5, Part 6 of this Code.
2.3.2 Aggregates
Concrete aggregates shall conform to the following standards:
BDS 243 : 1963, Coarse and Fine Aggregates from Natural Sources for Concrete; ASTM C33 / C33M - 08, Concrete
Aggregates; ASTM C330 / C330M - 09, Lightweight Aggregates for Structural Concrete; ASTM C637 - 09,
Aggregates for Radiation-Shielding Concrete; ASTM C332 - 09 , Lightweight Aggregate for Insulating Concrete; IS:
9142 Artificial Lightweight Aggregates for Concrete Masonry Units.
2.3.2.1 Special Tests
Aggregates failing to meet the specifications listed in Sec 2.4.2 shall not be used unless it is shown by special test
or actual service experience to produce concrete of adequate strength and durability and approved by the
Building Official.
2.3.2.2 Nominal Size
Nominal maximum size of coarse aggregate shall not be larger than:
a) One-fifth of the narrowest dimension between sides of forms; or
b) One-third the depth of slabs; or
c) Three fourths the minimum clear spacing between individual reinforcing bars or wires, bundles of
bars, or prestressing tendons or ducts.
Exception:
The above limitations regarding size of coarse aggregate may be waived if, in the judgment of the
Engineer, workability and methods of consolidation are such that concrete can be placed without
honeycomb or voids.
2.3.3 Cement
Cement shall conform to the following standards: BDS EN 197-1:2003 (Reaffirmed 2010), Cement Part-1
Composition, specifications and conformity criteria for common cements; BDS 612, Sulphate Resisting Portland
Cement-Type A; ASTM C150 / C150M - 09, BDS 232 Portland Cement; ASTM C595 / C595M - 10, Blended
Hydraulic Cements; and to other such cements listed in ACI 318.
2.3.4 Water
Water used in mixing concrete shall be clean and free from injurious amounts of oils, alkalies salts, organic
materials or other substances that may be deleterious to concrete or reinforcement.Water shall conform to the
following standards:BDS ISO 12439:2011 Mixing water for concrete.

Part 5
Building Materials

5-12 Vol. 2
2.3.4.1 Chloride Ions
Mixing water for prestressedconcrete, or for concrete that will contain aluminiumembededments, including the
portion of mixing water contributed in the form of free moisture on aggregates shall not contain deleterious
amounts of chloride ion. The maximum water-soluble chloride ion concentration in concrete shall not exceed the
limitations specified in Sec 5.5.3 of Part 6.
2.3.4.2 Potability
Nonpotable water shall not be used in concrete unless the following are satisfied:
a) Selection of concrete proportions shall be based on concrete mixes using water from such source.
b) Mortar test cubes made with nonpotable mixing water shall have 7-day and 28-day strengths equal
to at least 90 per cent of strengths of similar specimens made with potable water.
2.3.5 Admixtures
Admixtures to be used in concrete shall be subject to prior approval by the Building Official and shall comply with
Sec. 2.4.5.1 through 2.4.5.5.Admixtures shall conform to the following standards:
BDS EN 934-1:2008
Admixtures for concrete, mortar and grout Part 1: Common requirements
BDS EN 934-2:2008 Admixtures for concrete, mortar and grout Part 2: Concrete admixtures
Definitions, requirements, conformity, marking and
2.3.5.1 Chloride
Calcium chloride or admixtures containing chloride from admixture ingredients shall not be used inprestressed
concrete, concrete containing embedded aluminium in concrete cast against permanent galvanized metal forms,
or in concrete exposed to severe or very severe sulphate-containing solutions (see Sec 5.5.2.1 of Part 6).
2.3.5.2 Standards
Air-entraining admixtures shall conform to ASTM C260 - 06. Water-reducing admixtures, retarding admixtures,
accelerating admixtures, water-reducing and retarding admixtures, and water-reducing and accelerating
admixtures shall conform to ASTM C494 / C494M - 10, Chemical Admixtures for Concrete, or ASTM C1017 /
C1017M - 07, Chemical Admixtures for Use in Producing Flowing Concrete.
2.3.5.3 Pozzolanas
Fly ash (Pulverized Fuel Ash) or other pozzolanas used as admixtures shall conform to ASTM C618 - 08a.
2.3.5.4 Blast Furnace Slag
Ground granulated blast-furnace slag used as an admixture shall conform to ASTM C989 - 09a.
2.3.5.5 Pigment for Coloured Concrete
Pigment for integrally coloured concrete shall conform to ASTM C979 - 05.
2.3.6 Metal Reinforcement
Reinforcement and welding of reinforcement to be placed in concrete shall conform to the requirements of this
section.
a) Deformed Reinforcement : Deformed reinforcing bars shall conform to the following standards;BDS
ISO 6935-2:2010 (1st revision), Steel for the reinforcement of concrete - Part-2: Ribbed bars;

Reinforcement conforming to the ASTM, Standards: A615 / A615M, Deformed and Plain Billet-Steel
Bars; A616M, Rail-Steel Deformed and Plain Bars; A617M, Axle-Steel Deformed and Plain Bars;
A706M, Low-Alloy Steel Deformed Bars; A767M, Zinc Coated (Galvanized) Steel Bars; and A775M,
Epoxy-Coated Reinforcing Steel.
Deformed reinforcing bars with a specified yield strength exceeding 410 MPa may be used,
provided shall be the stress corresponding to a strain of 0.35 per cent and the bars otherwise
conform to ASTM standards noted above. Fabricated deformed steel bar mats conforming to ASTM
A184 / A184M - 06 and deformed steel wire complying with ASTM A496 / A496M - 07 may be used.
Deformed wire for concrete reinforcement shall not be smaller than size D4 (Nominal diameter : 5.72
mm), and for wire with a specified yield strength , exceeding 410 MPa shall be the stress
corresponding to a strain of 0.35 per cent.
Welded deformed steel wire fabric conforming to ASTM A497 / A497M - 07 may be used; for a wire
with a specified yield strength exceeding 410 MPa, shall be the stress corresponding to a strain of
0.35 per cent. Welded intersections shall not be spaced farther apart than 400 mm in direction of
calculated stress, except for wire fabric used as stirrups.
b) Plain Reinforcement : Plain reinforcement shall conform to the following BDS and ASTM
standards. BDS ISO 6935-1:2010 (1st revision); ASTM A615 / A615M - 09b; ASTM A996 / A996M - 09b
andASTM A996 / A996M - 09b. Steel welded wire, fabric plain reinforcement conforming to ASTM
A185 / A185M - 07 may be used, except that for wire with a specified yield strength exceeding 410
MPa, shall be the stress corresponding to a strain of 0.35 per cent. Welded intersections shall not be
spaced farther apart than 300 mm in direction of calculated stress, except for wire fabric used as
stirrups.
Smooth steel wire conforming to ASTM A182 / A182M - 09a may be used in concrete; except that for
a wire with a specified yield strength exceeding 410 MPa, shall be the stress corresponding to a
strain of 0.35 per cent.
c) Cold-worked Steel Reinforcement : Cold-worked steel high strength bars shall conform to IS
1786 : 1985 or BS 4461 : 1978.
d) PrestressingTendons : Wire, strands and bars for tendons in prestressed concrete shall conform
to BDS : 240, Plain Cold Drawn Steel Wire; ASTM A416 / A416M - 06, Steel Strand Uncoated Seven-
Wire Stress Relieved; ASTM A421 / A421M - 05, Uncoated Stress Relieved Steel Wire; and ASTM A722
/ A722M - 07, Uncoated High-Strength Steel Bar.
Wires, strands and bars not specifically listed in the above standards may be used, provided they
conform to minimum requirements of these specifications and do not have properties that make
them less satisfactory than those listed.
e) Stuctural Steel, Steel Pipe or Tubing : Structural steel used with reinforcing bars in
compositecompression members meeting the requirements of the Code shall conform to ASTM A36
/ A36M - 08, Structural Steel; ASTM A242 / A242M - 04(2009), High Strength Low-Alloy Structural
Steel; ASTM A572 / A572M - 07, High-Strength Low-Alloy Columbium-Vanadium Steel; and ASTM
A588 / A588M - 05, High-Strength Low-Alloy Structural Steel.
Steel pipe or tubing for composite compression members composed of a steel-encased concrete core
meeting the requirements of this Code shall conform to ASTM A53 / A53M - 07, Pipe, Steel, Black
and Hot Dipped Zinc Coated Welded and Seamless; ASTM A500 / A500M - 10 Cold-Formed Welded
and Seamless Carbon Steel Structural Tubing in Rounds and Shapes; and ASTM A501 - 07, Hot-
Formed Welded and Seamless Carbon Steel Structural Tubing.
Part 5
Building Materials

5-14 Vol. 2
2.3.7 Applicable Standards
Materials used in concrete shall comply with the applicable standards listed below.
BDS 279:1963 Specification for Abrasion of Coarse Aggregates by Use of Los
Angeles Machine (under revision);
BDS 281:1963 Specification for Organic Impurities in Sands for Concrete (under
revision);
BDS 921:1980 Specification for Standard Sand for Testing of Cement;
BDS 240:1963 Specification for Plain Cold Drawn Steel Wire for Prestressed
Concrete;
BDS 243:1963 Specification for Coarse and Fine Aggregates from Natural Sources
for Concrete;
BDS ISO 1920-8: 2010
Testing of Concrete Part 8: Determination of drying
shrinkage of concrete for samples prepared in the field or in
the laboratory
BDS ISO 1920-9: 2010
Testing of Concrete Part 9: Determination of creep of
concrete cylinders in compression
BDS ISO 1920-10: 2011
Testing of Concrete Part 10: Determination of static
modulus of elasticity in compression
BDS ISO 22965-1: 2008
Concrete Part 1: Methods of specifying and guidance for the
specifier
BDS ISO 22965-2: 2008
Concrete Part 2: Specification of constituent materials,
production of concrete and compliance of concrete
ASTM C31 / C31M - 09 Standard Practice for Making and Curing Concrete Test Specimens
in the Field
ASTM C39 / C39M - 09a Standard Test Method for Compressive Strength of Cylindrical
Concrete Specimens
ASTM C42 / C42M - 04 Standard Test Method for Obtaining and Testing Drilled Cores and
Sawed Beams of Concrete
ASTM C78 - 09 Standard Test Method for Flexural Strength of Concrete (Using
Simple Beam with Third-Point Loading)
ASTM C94 / C94M - 09a Standard Specification for Ready-Mixed Concrete
ASTM C172 - 08 Standard Practice for Sampling Freshly Mixed Concrete
ASTM C192 / C192M - 07 Standard Practice for Making and Curing Concrete Test Specimens
in the Laboratory
ASTM C317 / C317M -
00(2005)
Standard Specification for Gypsum Concrete

ASTM C496 / C496M -
04e1
Standard Test Method for Splitting Tensile Strength of Cylindrical
Concrete Specimens
ASTM C617 - 09a Standard Practice for Capping Cylindrical Concrete Specimens
ASTM C685 / C685M - 10 Standard Specification for Concrete Made by Volumetric Batching
and Continuous Mixing
ASTM C989 - 09a Standard Specification for Slag Cement for Use in Concrete and
Mortars

2.3.8 Concrete Pipe and Precast Sections
Concrete pipes and precast sections shall conform to the standards listed below :
BDS 1626:1999 Concrete pipes (with and without) reinforcement
ASTM C14M - 07 Standard Specification for Nonreinforced Concrete Sewer, Storm
Drain, and Culvert Pipe (Metric)
ASTM C76M - 10a Standard Specification for Reinforced Concrete Culvert, Storm
Drain, and Sewer Pipe (Metric)
ASTM C361M - 08 Standard Specification for Reinforced Concrete Low-Head
Pressure Pipe (Metric)
ASTM C444M - 03(2009) Standard Specification for Perforated Concrete Pipe (Metric)
ASTM C478M - 09 Standard Specification for Precast Reinforced Concrete Manhole
Sections (Metric)
ASTM C507M - 10a Standard Specification for Reinforced Concrete Elliptical Culvert,
Storm Drain, and Sewer Pipe (Metric)
ASTM C654M - 05a Standard Specification for Porous Concrete Pipe (Metric)
ASTM C655M - 09 Standard Specification for Reinforced Concrete D-Load Culvert,
Storm Drain, and Sewer Pipe (Metric)
ASTM C1433M - 10 Standard Specification for Precast Reinforced Concrete Monolithic
Box Sections for Culverts, Storm Drains, and Sewers (Metric)
ASTM C858 - 10 Standard Specification for Underground Precast Concrete Utility
Structures
ASTM C891 - 09 Standard Practice for Installation of Underground Precast
Concrete Utility Structures
ASTM C913 - 08 Standard Specification for Precast Concrete Water and
Wastewater Structures
Part 5
Building Materials

5-16 Vol. 2
ASTM C924M - 02(2009) Standard Practice for Testing Concrete Pipe Sewer Lines by Low-
Pressure Air Test Method (Metric)
IS 458:2003 Specification for precast concrete pipes (with and without
reinforcement) (fourth revision)
IS 784:2001 Specification for prestressed concrete pipes (including specials)
(second revision)
IS 1916:1989 Specification for steel cylinder pipewith concrete lining and
coating(first revision)
IS 3597:1998 Methods of test for concrete pipes (second revision)
IS 4350:1967 Specification for concrete porous pipes for under drainage
IS 7319:1974 Specification for perforated concrete pipes
IS 7322:1985 Specification for specials for steel cylinder reinforced concrete
pipes (first revision)
2.3.9 Asbestos Cement Products
Asbestos cement products shall conform to the following standards:
BDS 428:1964 Specification for Asbestos Cement Pressure Pipes (under revision);
BDS 429:1964 Specification for Asbestos Cement Building and Sanitary Pipes
(under revision);
BDS 430:1964

Specification for Asbestos Cement Corrugated Sheets for Roofing
and Cladding (under revision);
BDS 431:1964

Specification for Asymmetrical Section Corrugated Sheets in
Asbestos Cement for Roofing and Cladding (under revision);
BDS 579:1966

Specification for Asbestos Cement Flat Sheets (under revision);
BDS 1046:1983

Specification for Asbestos Cement Products-Corrugated Sheets and
Fittings for Roofing and Cladding;
ASTM C222 - 97(2008) Standard Specification for Asbestos-Cement Roofing Shingles
ASTM C223 - 98(2008) Standard Specification for Asbestos-Cement Siding
ASTM C500 - 07

Standard Test Methods for Asbestos-Cement Pipe
ASTM C508 / C508M -
00(2009)e1
Standard Specification for Asbestos-Cement Underdrain Pipe

ASTM C663 - 98(2008) Standard Specification for Asbestos-Cement Storm Drain Pipe
ASTM C875 - 98(2008) Standard Specification for Asbestos-Cement Conduit
ASTM C966 - 98(2008) Standard Guide for Installing Asbestos-Cement Nonpressure Pipe
2.4 PRE-STRESSED CONCRETE
2.4.1 Concrete for Pre-stressed Concrete
Cement and concrete required for pre-stressed concrete are elaborately described in section 2.3 of this part. BDS
and other standards for concrete as a material are also contained in the same section.
2.4.2 Steel for Pre-stressed Concrete
Steel and tendons for pre-stressed concrete along with the BDS and other standard requirements are included in
section 2.8 of this part.
Steel material for pre-stressed concrete shall also conform the following standards.
BDS ISO 6934 - 1 : 2008 Steel for the prestressing of concrete - Part 1: General
requirements
BDS ISO 6934 - 2 : 2008 Steel for the prestressing of concrete - Part 2 Cold-drawn wire
BDS ISO 6934 - 3 : 2008 Steel for the prestressing of concrete - Part 3 Quenched and
tempered wire
BDS ISO 6934 - 4 : 2008 Steel for the prestressing of concrete - Part 4 Strand
BDS ISO 6934- 5: 2008 Steel for the prestressing of concrete - Part 5 Hot-rolled steel
bars with or without subsequent processing
BDS ISO 6935 (Part-1): 2010
(1st revision)
Steel for the re-enforcement of concrete - Part-1: Plain bars
BDS ISO 6935 (Part-2): 2010
(1st revision)
Steel for the reinforcement of concrete - Part-2: Ribbed bars
BDS ISO 6935 (Part-3): 2006 Steel for the reinforcement of concrete - Part-3: Welded
Fabric. Specifies technical requirements for factory made
sheets or rolls welded fabric manufacture from steel wires or
bars with diameters from 4 mm to 16 mm and designed for
reinforcement in ordinary concrete structured and for non-
prestressed reinforcement in prestressed concrete structures.
BDS ISO 10065: 2006 Steel bars reinforcement of concrete Bend and Rebend tests
BDS ISO 15835-1:2010 Steel for the reinforcement of concrete Reinforcement
couplers for mechanical splices of bars Part 1: Requirements
Part 5
Building Materials

5-18 Vol. 2
BDS ISO 15835-2:2010 Steel for the reinforcement of concrete Reinforcement
couplers for mechanical splices of bars Part 2: Test methods
BDS ISO 10144:2006 Certification scheme for steel bars and wires for the
reinforcement of concrete structures.
BDS ISO 15630-1 : 2008 Steel for the reinforcement and prestressing of concrete
Test methods Part 1: Reinforcing bars, wire rod and wire
Test methods Part 2: Welded fabric
Test methods Part 3: Prestressing steel
BDS ISO 16020 : 2008 Steel for the reinforcement and prestressing of concrete
Vocabulary
2.5 BUILDING LIMES
2.5.1 Types of Lime
According to the degree of calcinations, slaking and setting actions and depending upon the nature and amount of
foreign matters associated with, the limes are classified as:
i. High calcium, fat, rich, common or pure lime
ii. Lean, meager or poor lime
iii. Hydraulic or water lime
2.5.2 Properties of Lime
A good lime shouid: slake readily in water, dissolve in soft water, free from fuel ashes and unburntparticles and
have good setting poer under water.
Building limes shall comply with the following ASTM standard specifications: ASTM C206 - 03, Finishing Hydrated
Lime; ASTM C207 - 06, Hydrated Lime for Masonry Purposes; ASTM C141 / C141M - 09, Hydraulic Hydrated Lime
for Structural Purposes; ASTM C977 - 03, Quicklime and Hydrated Lime for Soil Stabilization; and ASTM C5 - 03,
Quicklime for Structural Purposes.
The following Indian Standards may also be accepted for lime concrete and testing of building limes:
IS 712:1984 Specification for building limes (third revision)
IS 1624:1986 Method of field testing of building lime (first revision)
IS 712- 1984 Specification for building limes (third revision)
IS 1624 1986 Method of field testing of building lime ( first revision )
IS 2686-1977 Specification for Cinder Aggregates for Use in Lime Concrete
(First Revision);

IS 3068-1986 Specification for Broken Brick (burnt clay) Coarse Aggregates for
Use in Lime Concrete (Second Revision);
IS 3115-1992 Specification for Lime-based Blocks (Second Revision);
IS 3182-1986 Specification for Broken Brick (burnt clay) Fine Aggregates for
Use in Lime Mortar (second revision)
IS 4098-1983 Specification for Lime-Pozzolana Mixture (First Revision);
IS 4139-1989 Specification for Sand-lime Bricks (SecondRevision);
IS 6932 (Parts I to
X - 1973; Part XI-1983)
Method of Tests for Building Limes.
IS 10360-1982 Specification for Lime-Pozzolana Concrete Blocks for Paving;

IS 10772-1983 Specification for quick setting lime pozzolana mixture
IS 12894-2002

Specification for pulverized fuel ash lime bricks (First Revision)
2.6 GYPSUM BASED MATERIALS AND PLASTER
2.6.1 Gypsum Board
Gypsum wallboard, gypsum sheathing, gypsum base for gypsum veneer plaster, exterior gypsum soffitboard,
predecorated gypsum board or water-resistant gypsum backing board complying with the standards listed below
2.6.2 Gypsum Plaster
A mixture of calcined gypsum or calcined gypsum and lime and aggregate and other approved materials as
specified in this code.
2.6.3 Gypsum Veneer Plasteer
Gypsum plaster applied to an approved base in one or more coats normally not exceeding 1/4 inch (6.4 mm) in
total thickness.
2.6.4 Cement Plaster
A mixture of portland or blended cement, portland cement or blended cement and hydrated lime, masonry
cement or plastic cement and aggregate and other approved materials as specified in this code.
Gypsum building materials shall conform to the standards listed below.
ASTM C22 / C22M -
00(2005)e1
Standard Specification for Gypsum
ASTM C28 / C28M - 00(2005) Standard Specification for Gypsum Plasters
Part 5
Building Materials

5-20 Vol. 2
ASTM C35 - 01(2009) Standard Specification for Inorganic Aggregates for Use in
Gypsum Plaster
ASTM C1396 / C1396M - 09a Standard Specification for Gypsum Board
ASTM C59 / C59M - 00(2006) Standard Specification for Gypsum Casting Plaster and
Gypsum Molding Plaster
ASTM C317 / C317M -
00(2005)
Standard Specification for Gypsum Concrete
ASTM C471M - 01(2006)e1 Standard Test Methods for Chemical Analysis of Gypsum and
Gypsum Products [Metric]
ASTM C472 - 99(2009) Standard Test Methods for Physical Testing of Gypsum,
Gypsum Plasters and Gypsum Concrete
ASTM C473 - 09 Standard Test Methods for Physical Testing of Gypsum Panel
Products
ASTM C474 - 05 Standard Test Methods for Joint Treatment Materials for
Gypsum Board Construction
ASTM C587 - 04 Standard Specification for Gypsum Veneer Plaster
IS 2849-1983 Specification for Non-Load Bearing Gypsum Partition Blocks
(Solid and Hollow Types)
2.7 FLOORING MATERIALS
2.7.1 General
Flooring materials are generally of two types; precast systems like tiles, bricks and cast insitu.
2.7.2 Concrete/Terrazzo Tiles
Concrete/Terrazzo tiles shall have good abrasion and impact resistance properties. Factors such as the type of
cement and the type and grading of aggregate used influence the resistance of such tiles to chemicals including
cleaning agents. Terrazzo tiles shall have a wear layer after grinding at least 6 mm composed of graded marble
chipping in white, tinted or grey Portland cement on a layer of fine concrete. They may be ground after
manufacture to expose the marble aggregate and subsequently grouted. Slip resisting grits may be incorporated.
These tiles shall conform to BDS EN 13748-1:2008 Terrazzo tiles Part 1: Terrazzo tiles for internal use; BDS EN
13748-2:2008 Terrazzo tiles Part 2: Terrazzo tiles for external use; BDS 1262 : 1990 Clay flooring tiles; BDS 1248

: 1989 Ceramic Unglazed Vitreous acid resistant tiles or IS : 1237-1980, Specification for Cement Concrete Flooring
Tile.
2.7.3 Asphalt Tiles/Flooring
Asphalt tiles/floorings are suitable for industrial flooring in areas where they will not be exposed to solvents,
grease, oil, corrosive chemicals and excessive heat. Bitumen mastic for flooring shall conform to IS: 1195-1978; IS :
8374-1977, Bitumen Mastic, Anti-static and Electrically Conducting Grade and IS : 9510-1980, Bitumen Mastic Acid
Resisting Grade.
2.7.4 Mosaic Tiles
Mosaic tiles of a variety of shapes and sizes may be used. Thickness of the wear layer is dependent on the sizes of
marble chips but shall not be less than 6 mm thick. The tiles shall be wet cured for sufficient time before laying
so that their surfaces are not damaged during grinding and polishing.
2.7.5 Clay Tile
Clay floor tiles shall have sufficient strength and abrasion resistant characteristics to withstand the impact and
abrasion they are likely to be subject to. When glazed earthenware tiles are used in flooring they shall conform to
IS : 777:1970, Glazed Earthenware Tiles.
2.7.6 Vinyl Tiles
The vinyl tiles shall consist of a thoroughly blended composition of thermoplastic binder, asbestos fibre, fillers and
pigments. The thermoplastic binder shall consist substantially of either or both of the following:
a) vinyl chloride polymer
b) vinyl chloride copolymers.
The polymeric material shall be compounded with suitable plasticizers and stabilizers. The tiles may be plain,
patterned or mottled. The thickness shall not be less than 1.5 mm.
2.7.7 Rubber Tiles
These tiles are composed of natural, synthetic or reclaimed rubber, or a combination of these,with reinforcing
fibres, pigments, and fillers, vulcanized and moulded under pressure. The tiles shall have excellent resilience and
resistance to indentation, and good resistance to grease, alkali and abrasion. The thickness shall not be less than 2
mm.
2.7.8 Cast Insitu Floor Coverings
a) Terrazzo : Terrazzo is a marble mosaic with Portland cement matrix and is generally composed of two
parts marble chips to one part Portland cement. Colour pigments may be added. The thickness of
terrazzo topping may vary from 13 mm to 19 mm and may be applied to green concrete of the floor
or bonded with neat Portland cement, or over a sand cushion placed on the concrete floor.
b) Concrete : A concrete topping may be applied to a concrete structural slab before or after the base
slab has hardened. Integral toppings may generally be 25 mm to 40 mm thick; independent toppings
about 25 mm to 50 mm thick. Aggregate sizes shall not exceed 6 mm.
2.7.9 Other Flooring Materials
Other flooring materials i.e. bricks, natural stone, etc. showing satisfactory performance in similar situations may
be allowed. Plastic flooring tile and ceramic unglazed vitreous acid resistant tiles, if used, shall conform to IS :
3464 and IS : 4357 respectively.
Part 5
Building Materials

5-22 Vol. 2
Flooring compositions complying with IS : 657, Materials for Use in the Manufacture of Magnesium Oxychloride
Flooring Composition; and IS: 9197, Epoxy Resin Composition for Floor Topping may be allowed. Linoleum sheets
and tiles shall conform to IS : 653.
Flooring materials shall also conform to the standards listed below.
BDS 1248 : 1989 Ceramic Unglazed Vitreous acid resistant tilesIt covers the
requirements for ceramic unglazed vitreous acid resistant
tiles used in laying of floors & lining of tanks subjected to
corrosive conditions. Manufacture, Finish, Tests etc.
BDS 1262 : 1990 Clay flooring tilesIt specifies the requirements for dimensions,
quality & strength for clay flooring tiles & different types of
tests.
BDS ISO 10545 -1 : 2006 Ceramic tiles, Sampling and basis for acceptance. Specifies
rules for batching, sampling, inspection and
acceptance/rejection of ceramic tiles.
BDS ISO 10545 -2 : 2006 Ceramic tiles, Determination of dimensions and surface
quality Specifies methods for determining the dimensional
characteristics (length, width, thickness, straightness of sides,
rectangularity, and surface flatness) and the surface of
ceramic tiles.
BDS ISO 10545 -3 : 2006

Ceramic tiles, Determination of water absorption, apparent
porosity, apparent relative density and bulk density.
Specifies methods for determining water absorption,
apparent porosity, apparent relative density and bulk density
of ceramic tiles.
BDS ISO 10545 -4 : 2006 Ceramic tiles, Determination of modulus of rupture and
breaking strength
Defines a test method for determining the modulus of
rupture and breaking strength of all ceramic tiles.
BDS ISO 10545 -5 : 2005 Ceramic tiles, Determination of impact resistance by
measurement of coefficient of restitution
Specifies methods for determining the impact resistance of
ceramic tiles by measuring the coefficient of restitution.
BDS ISO 10545 -6 : 2006 Ceramic tiles, Determination of resistance to deep abrasion
for unglazed tiles.
BDS ISO 10545 -7 : 2006 Ceramic tiles, Determination of resistance to surface abrasion
for glazed tiles.
Specifies a method for determining the resistance to surface

abrasion of all glazed ceramic tiles used for floor covering.
BDS ISO 10545 -8 : 2006

Ceramic tiles, Determination of linear thermal expansion
Defines a test method for determining the coefficient of
linear thermal expansion of ceramic tiles.
BDS ISO 10545 -9 : 2006 Ceramic tiles, Determination of resistance to thermal shock.
Defines a test method for determining the resistance to
thermal shock of all ceramic tiles under normal conditions of
use.
BDS ISO 10545 -10 : 2006 Ceramic tiles, Determination of moisture expansion.
Specifies a method for determining the moisture expansion of
all ceramic tiles.
BDS ISO 10545 -11 : 2006 Ceramic tiles, Determination of crazing resistance for glazed
tiles.
Defines a test method for determining the crazing resistance
of all glazed ceramic tiles except when the crazing is an
inherent decorative feature of the product.
BDS ISO 10545 -12 : 2006 Ceramic tiles, Determination of frost resistance.
Specifies a method for determining the frost resistance of all
ceramic tiles intended for use in freezing conditions in the
presence of water.
BDS ISO 10545 -13 : 2006

Ceramic tiles, Determination of chemical resistance.
Specifies a test method for determining the chemical
resistance of all ceramic tiles at room temperature. The
method is applicable to all types of ceramic tiles.
BDS ISO 10545 -14 : 2006

Ceramic tiles, Determination of resistance to stains.
Specifies a method for determining the resistance to stains of
the proper surface of ceramic tiles.
BDS ISO 10545 -15 : 2006

Ceramic tiles, Determination of lead and cadmium given off
by glazed tiles.
Specifies a method for the determination of lead and
cadmium given off by the glaze of ceramic tiles.
Part 5
Building Materials

5-24 Vol. 2
BDS ISO 10545 -16 : 2006 Ceramic tiles, Determination of small color differences.
Describes a method for utilizing color measuring instruments
for quantifying the small color differences between plain
colored glazed ceramic tiles, which are designed to be
uniform and consistent color It permits the specification of a
maximum acceptable value which depends only on the
closeness of match and not on the nature of the color
difference.
BDS EN 490: 2008 Concrete roofing tiles and fittings for roof covering and all
cladding Product specifications.
BDS ISO 13006 : 2006

Ceramic tiles - Definitions, Classification, Characteristics and
Marking.
This Bangladesh Standard defines terms and establishes
classifications characteristics and marking requirements for
ceramic tiles of the best commercial quality (first quality).
BDS EN 491: 2008 Concrete roofing tiles and fittings for roof covering and wall
cladding Test methods
BDS EN 538: 2008 Clay roofing tiles for discontinuous laying Flexural strength
test
BDS EN 539-1: 2008 Clay roofing tiles for discontinuous laying Determination of
physical characteristics Part 1: Impermeability test
BDS EN 1024: 2008 Clay roofing tiles for discontinuous laying Determination of
geometric characteristics
BDS EN 1304: 2008

Clay roofing tiles and fittings Product definitions and
specifications
BDS EN 13748-1: 2008 Terrazzo tiles Part 1: Terrazzo tiles for internal use
BDS EN 13748-2: 2008 Terrazzo tiles Part 2: Terrazzo tiles for external use
2.8 STEEL
2.8.1 Reinforcing Steel
Reinforcing steel shall comply with the requirements specified in Sec 2.4.6 in this Part.
2.8.2 Structural Steel
Structural steel shall conform to Bangladesh Standards BDS 878 : 1978, Specification for Weldable Structural
Steels; BDS 1355 : 1992, Dimensions and Properties of Hot Rolled Steel Beam, Column, Channel and Angle
Sections. Where Bangladesh standards are not available, the relevant standards listed below shall be applicable.

BDS 1429:1993 Light gauge steel sections
BDS ISO 2566-1:2008 Steel Conversion of elongation values Part 1: Carbon
and low alloy steels
BDS ISO 2566-2:2008 Steel - Conversion of elongation values - Part 2: Austenitic
steels
BDS ISO 657-1:2008 Hot-rolled steel sections - Part 1: Equal-leg angles
Dimensions
BDS ISO 657-2:2008 Hot-rolled steel sections - Part 2: Unequal-leg angles
Dimensions
BDS ISO 657-5:2008 Hot-rolled steel sections -Part V Equal-leg angles and
unequal leg angles Tolerances for metric and inch series
BDS ISO 657-11:2008 Hot-rolled steel sections Part 11: Sloping flange channel
sections (Metric series) Dimensions and sectional
properties
BDS ISO 657-15:2008 Hot-rolled steel sections - Part 15 Sloping flange beam
sections (Metric series) - Dimensions and sectional
properties
BDS ISO 657-16:2008 Hot-rolled steel sections Part 16: Sloping flange column
sections (metric series) Dimensions and sectional
properties
BDS ISO 657-18:2008 Hot-rolled steel sections Part 18: L sections for
shipbuilding (metric series) 104 Dimensions, sectional
properties and tolerances
BDS ISO 657-19:2008 Hot-rolled steel sections Part 19: Bulb flats (metric series)
Dimensions, sectional properties and tolerances
BDS ISO 657-21:2008 Hot-rolled steel sections - Part 21 T-sections with equal
depth and flange width - Dimensions
BDS ISO 10474:2008 Steel and steel products Inspection documents
BDS ISO 14284:2008 Steel and iron Sampling and preparation of samples for
the determination of chemical composition
BDS ISO 9769:2008 Steel and iron Review of available methods of analysis
BDS ISO 6929:2008 Steel products Definition and classification
BDS ISO 20723:2008 Structural steels Surface condition of hot-rolled sections
Delivery requirements
Part 5
Building Materials

5-26 Vol. 2
BDS ISO 24314:2008 Structural steels Structural steels for building with
improved seismic resistance Technical delivery conditions
BDS ISO 404:2008 Steel and steel productsGeneral technical delivery
requirements
BDS ISO 1127: 2006 Stainless steel tubes - Dimensions, tolerances and
conventional masses per unit length.
BDS ISO 4200: 2006 Plain end steel tubes, welded and seamless - General tables
of dimensions and masses per unit length.
BDS ISO 6761:2008 Steel tubes Preparation of ends of tubes and fittings for
welding
ASTM A27 / A27M - 08 Standard Specification for Steel Castings, Carbon, for General
Application
ASTM A36 / A36M - 08 Standard Specification for Carbon Structural Steel
ASTM A48 / A48M - 03(2008) Standard Specification for Gray Iron Castings
ASTM A53 / A53M - 07 Standard Specification for Pipe, Steel, Black and Hot-Dipped,
Zinc-Coated, Welded and Seamless
ASTM A148 / A148M - 08 Standard Specification for Steel Castings, High Strength, for
Structural Purposes
ASTM A242 / A242M -
04(2009)
Standard Specification for High-Strength Low-Alloy Structural
Steel
ASTM A252 - 98(2007) Standard Specification for Welded and Seamless Steel Pipe
Piles
ASTM A283 / A283M -
03(2007)
Standard Specification for Low and Intermediate Tensile
Strength Carbon Steel Plates
ASTM A307 - 07b Standard Specification for Carbon Steel Bolts and Studs, 60
000 PSI Tensile Strength
ASTM A325 - 09ae1 Standard Specification for Structural Bolts, Steel, Heat
Treated, 120/105 ksi Minimum Tensile Strength
ASTM A325M - 09 Standard Specification for Structural Bolts, Steel, Heat
Treated 830 MPa Minimum Tensile Strength [Metric]
ASTM A336 / A336M - 09 Standard Specification for Alloy Steel Forgings for Pressure
and High-Temperature Parts
ASTM A653 / A653M - 09a Standard Specification for Steel Sheet, Zinc-Coated
(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the

Hot-Dip Process
ASTM A449 - 07b Standard Specification for Hex Cap Screws, Bolts and Studs,
Steel, Heat Treated, 120/105/90 ksi Minimum Tensile
Strength, General Use
ASTM A490 - 09 Standard Specification for Structural Bolts, Alloy Steel, Heat
Treated, 150 ksi Minimum Tensile Strength
ASTM A500 / A500M - 10 Standard Specification for Cold-Formed Welded and
Seamless Carbon Steel Structural Tubing in Rounds and
Shapes
ASTM A501 - 07 Standard Specification for Hot-Formed Welded and Seamless
Carbon Steel Structural Tubing
ASTM A514 / A514M -
05(2009)
Standard Specification for High-Yield-Strength, Quenched
and Tempered Alloy Steel Plate, Suitable for Welding
ASTM A529 / A529M -
05(2009)
Standard Specification for High-Strength Carbon-Manganese
Steel of Structural Quality
ASTM A563 - 07a Standard Specification for Carbons and Alloy Steel Nuts
ASTM A563M - 07 Standard Specification for Carbon and Alloy Steel Nuts
[Metric]
ASTM A1011 / A1011M - 10

Standard Specification for Steel, Sheet and Strip, Hot-Rolled,
Carbon, Structural, High-Strength Low-Alloy, High-Strength
Low-Alloy with Improved Formability, and Ultra-High
Strength
ASTM A572 / A572M - 07 Standard Specification for High-Strength Low-Alloy
Columbium-Vanadium Structural Steel
ASTM A588 / A588M - 05 Standard Specification for High-Strength Low-Alloy Structural
Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with
Atmospheric Corrosion Resistance
ASTM A606 / A606M - 09a

Standard Specification for Steel, Sheet and Strip, High-
Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, with
Improved Atmospheric Corrosion Resistance
ASTM A1008 / A1008M - 10

Structural, High-Strength Low-Alloy, High-Strength Low-Alloy
with Improved Formability, Solution Hardened, and Bake
Hardenable
ASTM A618 / A618M - 04 Standard Specification for Hot-Formed Welded and Seamless
High-Strength Low-Alloy Structural Tubing
Part 5
Building Materials

5-28 Vol. 2
ASTM A666 - 03 Standard Specification for Annealed or Cold-Worked
Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
ASTM A668 / A668M -
04(2009)
Standard Specification for Steel Forgings, Carbon and Alloy,
for General Industrial Use
ASTM A690 / A690M - 07 Standard Specification for High-Strength Low-Alloy Nickel,
Copper, Phosphorus Steel H-Piles and Sheet Piling with
Atmospheric Corrosion Resistance for Use in Marine
Environments
ASTM A852 / A852M -
03(2007)
Standard Specification for Quenched and Tempered Low-
Alloy Structural Steel Plate with 70 ksi [485 MPa] Minimum
Yield Strength to 4 in. [100 mm] Thick
2.8.3 Steel Plate, Sheet and Strips
These shall conform to the following standards.
BDS 868 : 1978 Code of Practice for Galvanized Corrugated Sheet Roof and Wall
Coverings;
BDS 1122 : 1985 Specification for Hot-dip Galvanized Steel Sheet and Coil;
BDS ISO 9328-1:2009 Steel flat products for pressure purposes Technical delivery
conditions Part 1: General requirements
conditions Part 2: Non-alloy and alloy steels with specified
elevated temperature properties
conditions Part 3: Weldable fine grain steels, normalized
conditions Part 4: Nickel-alloy steels with specified low
temperature properties
conditions Part 5: Weldable fine grain steels, thermo
mechanically rolled
conditions Part 6: Weldable fine grain steels, quenched and
tempered
conditions Part 7: Stainless steels
BDS ISO 4995:2006 Hot-rolled steel sheet of structural quality

BDS ISO 7452:2008 Hot-rolled structural steel plates Tolerances on dimensions and
shape
BDS ISO 7778:2008 Steel plate with specified through-thickness characteristics
BDS ISO 7788:2008 Steel Surface finish of hot-rolled plates and wide flats Delivery
requirements
BDS ISO 9034:2008 Hot-rolled structural steel wide flats Tolerances on dimensions
and shape
BDS ISO 9364:2011 Continuous hot-dip aluminium/zinc coated steel sheet of
commercial, drawing and structural qualities
BDS ISO 16160:2011 Continuously hot-rolled steel sheet products Dimensional and
shape tolerances
BDS ISO16162:2011 Continuously cold-rolled steel sheet products Dimensional and
shape tolerances
BDS ISO 16163:2011 Continuously hot-dipped coated steel sheet products
Dimensional and shape tolerances
IS 412 : 1975 Specification for Expanded Metal Steel Sheets for General
Purposes (Second Revision);
IS 1079 : 1994 Specification for hot rolled carbon steel sheet and strip (fifth
revision)
IS 4030 : 1973 Specification for Cold-Rolled Carbon Steel Strip for General
Engineering Purposes (First Revision);
IS 7226 : 1974 Specification for Cold-Rolled Medium, High Carbon and Low-Alloy
Steel Strip for General Engineering Purposes;
IS 3502 : 1994 Specification for steel chequered plates (second revision)
ASTM A109 / A109M - 08 Standard Specification for Steel, Strip, Carbon (0.25 Maximum
Percent), Cold-Rolled
ASTM A123 / A123M - 09 Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on
Iron and Steel Products
ASTM A167 - 99(2009) Standard Specification for Stainless and Heat-Resisting Chromium-
Nickel Steel Plate, Sheet, and Strip
ASTM A176 - 99(2009) Standard Specification for Stainless and Heat-Resisting Chromium
Steel Plate, Sheet, and Strip
ASTM A240 / A240M - 10

Standard Specification for Chromium and Chromium-Nickel
Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for
Part 5
Building Materials

5-30 Vol. 2
General Applications
ASTM A263 - 09 Standard Specification for Stainless Chromium Steel-Clad Plate
ASTM A264 - 09 Specification for Stainless Chromium-Nickel Steel-Clad Plate
ASTM A285 / A285M -
03(2007)
Standard Specification for Pressure Vessel Plates, Carbon Steel,
Low- and Intermediate-Tensile Strength
ASTM A328 / A328M - 07 Standard Specification for Steel Sheet Piling
ASTM A1008 / A1008M -
10
Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with
Improved Formability, Solution Hardened, and Bake Hardenable
ASTM A414 / A414M - 10 Standard Specification for Steel, Sheet, Carbon, and High-
Strength, Low-Alloy for Pressure Vessels
ASTM A424 / A424M -
09a
Standard Specification for Steel, Sheet, for Porcelain Enameling
ASTM A929 / A929M -
01(2007)
Standard Specification for Steel Sheet, Metallic-Coated by the
Hot-Dip Process for Corrugated Steel Pipe
ASTM A463 / A463M -
09a
Standard Specification for Steel Sheet, Aluminum-Coated, by the
Hot-Dip Process
ASTM A480 / A480M - 10 Standard Specification for General Requirements for Flat-Rolled
Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
ASTM A505 - 00(2005) Standard Specification for Steel, Sheet and Strip, Alloy, Hot-Rolled
and Cold-Rolled, General Requirements for
ASTM A506 - 05 Standard Specification for Alloy and Structural Alloy Steel, Sheet
and Strip, Hot-Rolled and Cold-Rolled
ASTM A507 - 10 Standard Specification for Drawing Alloy Steel, Sheet and Strip,
Hot-Rolled and Cold-Rolled
ASTM A653 / A653M -
09a
Standard Specification for Steel Sheet, Zinc-Coated (Galvanized)
or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
ASTM A568 / A568M -
09a
Standard Specification for Steel, Sheet, Carbon, Structural, and
High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General
Requirements for
ASTM A577 / A577M -
90(2007)
Standard Specification for Ultrasonic Angle-Beam Examination of
Steel Plates
ASTM A578 / A578M - 07 Standard Specification for Straight-Beam Ultrasonic Examination
of Rolled Steel Plates for Special Applications

ASTM A879 / A879M - 06 Standard Specification for Steel Sheet, Zinc Coated by the
Electrolytic Process for Applications Requiring Designation of the
Coating Mass on Each Surface
ASTM A599 / A599M - 07 Standard Specification for Tin Mill Products, Electrolytic Tin-
Coated, Cold-Rolled Sheet
ASTM A606 / A606M -
09a
Standard Specification for Steel, Sheet and Strip, High-Strength,
Low-Alloy, Hot-Rolled and Cold-Rolled, with Improved
Atmospheric Corrosion Resistance
ASTM A635 / A635M -
09b
Standard Specification for Steel, Sheet and Strip, Heavy-Thickness
Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-
Alloy, and High-Strength Low-Alloy with Improved Formability,
General Requirements for
ASTM A653 / A653M -
09a
ASTM A653 / A653M -
09a
ASTM A666 - 03 Standard Specification for Annealed or Cold-Worked Austenitic
Stainless Steel Sheet, Strip, Plate, and Flat Bar
ASTM A690 / A690M - 07 Standard Specification for High-Strength Low-Alloy Nickel,
Copper, Phosphorus Steel H-Piles and Sheet Piling with
Atmospheric Corrosion Resistance for Use in Marine
Environments
ASTM A775 / A775M -
07b
Standard Specification for Epoxy-Coated Steel Reinforcing Bars
ASTM A792 / A792M -
09a
Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-
Coated by the Hot-Dip Process
ASTM A857 / A857M - 07 Standard Specification for Steel Sheet Piling, Cold Formed, Light
Gage
ASTM A875 / A875M -
09a
Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-
Coated by the Hot-Dip Process
2.8.4 Steel Pipe, Tube and Fittings
These items shall conform to the following standards :
BDS ISO 49:2008 Malleable cast iron fittings threaded to ISO 7-1
BDS ISO 3545-3:2008 Steel tubes and fittings Symbols for use in specifications Part
3: Tubular fittings with circular cross-section
Part 5
Building Materials

5-32 Vol. 2
BDS ISO 4144:2008 Pipe work Stainless steel fittings threaded in accordance with
ISO 7-1
BDS ISO 4145:2008 Non-alloy steel fittings threaded to ISO 7-1
BDS ISO 3419:2008 Non alloy and alloy steel buttwelding fittings
BDS ISO 5251:2008 Stainless steel buttwelding fittings
ASTM A105 / A105M - 09 Standard Specification for Carbon Steel Forgings for Piping
Applications
ASTM A106 / A106M - 08 Standard Specification for Seamless Carbon Steel Pipe for High-
Temperature Service
ASTM A134 - 96(2005) Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-
Welded (Sizes NPS 16 and Over)
ASTM A139 / A139M - 04 Standard Specification for Electric-Fusion (Arc)-Welded Steel
Pipe (NPS 4 and Over)
ASTM A181 / A181M - 06 Standard Specification for Carbon Steel Forgings, for General-
Purpose Piping
ASTM A182 / A182M - 09a Standard Specification for Forged or Rolled Alloy and Stainless
Steel Pipe Flanges, Forged Fittings, and Valves and Parts for
High-Temperature Service
ASTM A234 / A234M - 07 Standard Specification for Piping Fittings of Wrought Carbon
Steel and Alloy Steel for Moderate and High Temperature
Service
ASTM A252 - 98(2007) Standard Specification for Welded and Seamless Steel Pipe
Piles
ASTM A254 - 97(2007) Standard Specification for Copper-Brazed Steel Tubing
ASTM A268 / A268M - 10

Standard Specification for Seamless and Welded Ferritic and
Martensitic Stainless Steel Tubing for General Service
ASTM A269 - 10 Standard Specification for Seamless and Welded Austenitic
Stainless Steel Tubing for General Service
ASTM A270 - 03a(2008)e1 Standard Specification for Seamless and Welded Austenitic
Stainless Steel Sanitary Tubing
ASTM A312 / A312M - 09 Standard Specification for Seamless, Welded, and Heavily Cold

Worked Austenitic Stainless Steel Pipes
ASTM A333 / A333M - 10 Standard Specification for Seamless and Welded Steel Pipe for
Low-Temperature Service
ASTM A334 / A334M - 04a Standard Specification for Seamless and Welded Carbon and
Alloy-Steel Tubes for Low-Temperature Service
ASTM A403 / A403M - 09 Standard Specification for Wrought Austenitic Stainless Steel
Piping Fittings
ASTM A420 / A420M - 07 Standard Specification for Piping Fittings of Wrought Carbon
Steel and Alloy Steel for Low-Temperature Service
ASTM A423 / A423M - 09 Standard Specification for Seamless and Electric-Welded Low-
Alloy Steel Tubes
ASTM A450 / A450M - 09 Standard Specification for General Requirements for Carbon
and Low Alloy Steel Tubes
ASTM A500 / A500M - 10 Standard Specification for Cold-Formed Welded and Seamless
Carbon Steel Structural Tubing in Rounds and Shapes
ASTM A501 - 07 Standard Specification for Hot-Formed Welded and Seamless
Carbon Steel Structural Tubing
ASTM A522 / A522M - 07 Standard Specification for Forged or Rolled 8 and 9% Nickel
Alloy Steel Flanges, Fittings, Valves, and Parts for Low-
Temperature Service
ASTM A524 - 96(2005) Standard Specification for Seamless Carbon Steel Pipe for
Atmospheric and Lower Temperatures
ASTM A530 / A530M - 04a Standard Specification for General Requirements for
Specialized Carbon and Alloy Steel Pipe
ASTM A589 / A589M - 06 Standard Specification for Seamless and Welded Carbon Steel
Water-Well Pipe
ASTM A618 / A618M - 04 Standard Specification for Hot-Formed Welded and Seamless
High-Strength Low-Alloy Structural Tubing
ASTM A632 - 04(2009) Standard Specification for Seamless and Welded Austenitic
Stainless Steel Tubing (Small-Diameter) for General Service
ASTM A707 / A707M -
02(2007)
Standard Specification for Forged Carbon and Alloy Steel
Flanges for Low-Temperature Service
ASTM A733 - 03(2009)e1 Standard Specification for Welded and Seamless Carbon Steel
and Austenitic Stainless Steel Pipe Nipples
Part 5
Building Materials

5-34 Vol. 2
ASTM A778 - 01(2009)e1 Standard Specification for Welded, Unannealed Austenitic
Stainless Steel Tubular Products
ASTM A807 / A807M -
02(2008)

Standard Practice for Installing Corrugated Steel Structural
Plate Pipe for Sewers and Other Applications
ASTM A865 / A865M - 06 Standard Specification for Threaded Couplings, Steel, Black or
Zinc-Coated (Galvanized) Welded or Seamless, for Use in Steel
Pipe Joints
2.8.5 Steel Bars, Wire and Wire Rods
These shall conform to the following standards.
BDS ISO 1035-1:2006 Hot-rolled steel bars-Part 1: Dimensions of round bars.
BDS ISO 1035-2:2006 Hot-rolled steel bars-Part 2: Dimensions of square bars.
BDS ISO 1035-3:2006 Hot-rolled steel bars-Part 3: Dimensions of flat bars.
BDS ISO 1035-4:2006 Hot-rolled steel bars-Part 4: Tolerances.
BDS ISO 4951-1:2008 High yield strength steel bars and sections Part 1: General
delivery requirements
BDS ISO 4951-2:2008 High yield strength steel bars and sections Part 2: Delivery
conditions for normalized, normalized rolled and as-rolled
steels
BDS ISO 4951-3:2008 High yield strength steel bars and sections Part 3: Delivery
conditions for thermo mechanically-rolled steels
ASTM A29 / A29M - 05 Standard Specification for Steel Bars, Carbon and Alloy, Hot-
Wrought, General Requirements for
ASTM A49 - 01(2006) Standard Specification for Heat-Treated Carbon Steel Joint
Bars, Microalloyed Joint Bars, and Forged Carbon Steel
Compromise Joint Bars
ASTM A108 - 07 Standard Specification for Steel Bar, Carbon and Alloy, Cold-
Finished
ASTM A116 - 05 Standard Specification for Metallic-Coated, Steel Woven Wire
Fence Fabric
ASTM A185 / A185M - 07 Standard Specification for Steel Welded Wire Reinforcement,
Plain, for Concrete
ASTM A227 / A227M - 06 Standard Specification for Steel Wire, Cold-Drawn for

Mechanical Springs
ASTM A228 / A228M - 07 Standard Specification for Steel Wire, Music Spring Quality
ASTM A229 / A229M -
99(2005)
Standard Specification for Steel Wire, Oil-Tempered for
Mechanical Springs
ASTM A276 - 08a Standard Specification for Stainless Steel Bars and Shapes
ASTM A311 / A311M - 04

Standard Specification for Cold-Drawn, Stress-Relieved Carbon
Steel Bars Subject to Mechanical Property Requirements
ASTM A322 - 07 Standard Specification for Steel Bars, Alloy, Standard Grades
ASTM A108 - 07 Standard Specification for Steel Bar, Carbon and Alloy, Cold-
Finished
ASTM A368 - 95a(2009) Standard Specification for Stainless Steel Wire Strand
ASTM A434 - 06 Standard Specification for Steel Bars, Alloy, Hot-Wrought or
Cold-Finished, Quenched and Tempered
ASTM A475 - 03(2009)e1 Standard Specification for Zinc-Coated Steel Wire Strand
ASTM A478 - 97(2008) Standard Specification for Chromium-Nickel Stainless Steel
Weaving and Knitting Wire
ASTM A479 / A479M - 10 Standard Specification for Stainless Steel Bars and Shapes for
Use in Boilers and Other Pressure Vessels
ASTM A492 - 95(2009) Standard Specification for Stainless Steel Rope Wire
ASTM A499 - 89(2008)

Standard Specification for Steel Bars and Shapes, Carbon Rolled
from T Rails
ASTM A510 - 08

Standard Specification for General Requirements for Wire Rods
and Coarse Round Wire, Carbon Steel
ASTM A575 - 96(2007) Standard Specification for Steel Bars, Carbon, Merchant
Quality, M-Grades
ASTM A576 - 90b(2006) Standard Specification for Steel Bars, Carbon, Hot-Wrought,
Special Quality
ASTM A580 / A580M - 08 Standard Specification for Stainless Steel Wire
ASTM A586 - 04a(2009)e1 Standard Specification for Zinc-Coated Parallel and Helical Steel
Wire Structural Strand
ASTM A603 - 98(2009)e1 Standard Specification for Zinc-Coated Steel Structural Wire
Rope
Part 5
Building Materials

5-36 Vol. 2
ASTM A627 - 03 Standard Test Methods for Tool-Resisting Steel Bars, Flats, and
Shapes for Detention and Correctional Facilities
ASTM A627 - 03 Standard Test Methods for Tool-Resisting Steel Bars, Flats, and
Shapes for Detention and Correctional Facilities
ASTM A663 / A663M -
89(2006)
standard Specification for Steel Bars, Carbon, Merchant
Quality, Mechanical Properties
ASTM A666 - 03 Standard Specification for Annealed or Cold-Worked Austenitic
Stainless Steel Sheet, Strip, Plate, and Flat Bar
ASTM A706 / A706M - 09b Standard Specification for Low-Alloy Steel Deformed and Plain
ASTM A764 - 07

Standard Specification for Metallic Coated Carbon Steel Wire,
Coated at Size and Drawn to Size for Mechanical Springs
ASTM C933 - 09 Standard Specification for Welded Wire Lath

2.8.6 Steel Fasteners
Steel fasteners shall conform to the following standards:
BDS 1373 : 1992 Slotted countersunk flat head tapping screws
BDS 1374 : 1992 Slotted raised counter
BDS 1375 : 1992 Fasteners hexagon products widths across flats
BDS 1405:1993 Bolts, Screws, Nuts and Accessories Terminology and
Nomenclature
BDS 1406:1993 Hexagon nuts style 2 products grades A and B.
BDS 1407:1993 Hexagon nuts style 3 products grades A and B.
BDS 1408:1993 General purpose screw threads general plan
BDS 1409:1993 General purpose screw threads selected sizes for screws, bolts
and nuts
BDS 1410:1993 Thread run-outs for fasteners thread of BDS 1408: 1995 and
BDS 1411:1993 Tapping screws thread
BDS 1412:1993 Thread undercuts of external metric thread fasteners
BDS 1413:1993 Head configuration and gauging of countersunk head screws

BDS 1428 : 1993 Fasteners-bolts, screws, studs and nuts-symbols and
designations of dimensions
ASTM A31 - 04(2009) Standard Specification for Steel Rivets and Bars for Rivets,
Pressure Vessels
ASTM A183 - 03(2009) Standard Specification for Carbon Steel Track Bolts and Nuts
ASTM A193 / A193M - 09 Standard Specification for Alloy-Steel and Stainless Steel
Bolting Materials for High Temperature or High Pressure
Service and Other Special Purpose Applications
ASTM A194 / A194M - 10 Standard Specification for Carbon and Alloy Steel Nuts for Bolts
for High Pressure or High Temperature Service, or Both
ASTM A307 - 07b Standard Specification for Carbon Steel Bolts and Studs, 60 000
PSI Tensile Strength
ASTM A320 / A320M - 08 Standard Specification for Alloy-Steel and Stainless Steel
Bolting Materials for Low-Temperature Service
ASTM A325 - 09ae1 Standard Specification for Structural Bolts, Steel, Heat Treated,
120/105 ksi Minimum Tensile Strength
ASTM A354 - 07a Standard Specification for Quenched and Tempered Alloy Steel
Bolts, Studs, and Other Externally Threaded Fasteners
ASTM A437 / A437M - 10 Standard Specification for Stainless and Alloy-Steel Turbine-
Type Bolting Specially Heat Treated for High-Temperature
Service

ASTM A449 - 07b Standard Specification for Hex Cap Screws, Bolts and Studs,
Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength,
General Use
ASTM A489 - 04e1 Standard Specification for Carbon Steel Lifting Eyes
ASTM A490 - 09 Standard Specification for Structural Bolts, Alloy Steel, Heat
Treated, 150 ksi Minimum Tensile Strength
ASTM A502 - 03(2009) Standard Specification for Rivets, Steel, Structural
ASTM A540 / A540M - 10 Standard Specification for Alloy-Steel Bolting for Special
Applications
ASTM A563 - 07a Standard Specification for Carbons and Alloy Steel Nuts
ASTM C954 - 07

Standard Specification for Steel Drill Screws for the Application
of Gypsum Panel Products or Metal Plaster Bases to Steel Studs
Part 5
Building Materials

5-38 Vol. 2
from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness
ASTM C955 - 09a Standard Specification for Load-Bearing (Transverse and Axial)
Steel Studs, Runners (Tracks), and Bracing or Bridging for Screw
Application of Gypsum Panel Products and Metal Plaster Bases
ASTM F959 - 09 Standard Specification for Compressible-Washer-Type Direct
Tension Indicators for Use with Structural Fasteners
ASTM C1002 - 07 Standard Specification for Steel Self-Piercing Tapping Screws
for the Application of Gypsum Panel Products or Metal Plaster
Bases to Wood Studs or Steel Studs
ASTM F436 - 09 Standard Specification for Hardened Steel Washers
ASTM F593 - 02(2008) Standard Specification for Stainless Steel Bolts, Hex Cap
Screws, and Studs
ASTM F594 - 09 Standard Specification for Stainless Steel Nuts
ASTM F844 - 07a

Standard Specification for Washers, Steel, Plain (Flat),
Unhardened for General Use
ASTM A574 - 08 Standard Specification for Alloy Steel Socket-Head Cap Screws
ASTM C514 - 04(2009)e1 Standard Specification for Nails for the Application of Gypsum
Board
2.8.7 Welding Electrodes and Wires
Welding electrodes and wires shall conform to the following standards :
BDS 1442-1:1994 Filler rods and wire for gas shielded arc-welding-Ferric steel
BDS 1442-2:1994 Filler rods and wire for gas shielded arc-welding-Austenitic
stainless steel
BDS 1442-3:1994 Filler rods and wires for gas shielded arc welding-copper and
copper alloy
BDS 1442-4:1994 Filler rods and wires for gas shielded arc welding-Aluminium
and Aluminium alloy and magnesium alloys
BDS 1442-5:1994 Filler rods and wires for gas shielded arc welding-Nickel and
nickel alloys
IS 814 - 1991 Specification for covered electrodes for manual metal arc
welding of carbon and carbon manganese steel (fifth revision)
IS 815-1974 Classification and Coding of Covered Electrodes for Metal Arc
Welding of Structural Steels (Second Revision);

IS 1278-1972 Specification for Filler Rods and Wires for Gas Welding (Second
Revision);
IS 1395-1982

Specification for Low and Medium Alloy Steel Covered
Electrodes for Manual Metal Arc Welding (Third Revision);
IS 3613-1974

Acceptance Tests for Wire Flux Combinations for Submerged-
Arc Welding of Structural Steel (First Revision);
IS 4972-1968 Specification for Resistance Spot-Welding Electrodes;
IS 6419-1996

Specification for welding rods and bare electrodes for gas
shielded arc welding of structural steel (first revision);
IS 6560-1996 Specification for molybdenum and chromium-molybdenum
low alloy steel welding rods and bare electrodes for gas
shielded arc welding (first revision);
IS 7280-1974 Specification for Base Wire Electrodes for Submerged-Arc
Welding of Structural Steels;
IS 8363-1976 Specification for Bare Wire Electrodes for Electroslag Welding
of Streels;
BDS 239: 1963

Specification for Soft Solder (under revision);
ISO 9453:1990 Soft Solder Alloys-Chemical Compositions and Forms;
ISO 9454:1990

Soft Soldering Fluxes-Classification and Requirements
Part 1 : Classification, Labelling and Packaging;
ISO 9455-1: 1990 Soft Soldering Fluxes- Test Methods
Part 1 : Determination of Non-volatile Matter, Gravimetric
Method;
ISO 9455-8:1991 Soft Soldering Fluxes-Test Methods
Part 8 : Determination of Zinc Content;
Part 11 : Solubility of Flux Residues;
Part 14 : Assessment of Tacriness of Flux Residues.
Part 5
Building Materials

5-40 Vol. 2
2.9 TIMBER & WOOD PRODUCTS
2.9.1 Timber Types and Properties
Timber types for the structural purpose with their engineering characteristics are contained in Table 6.11.1 of
Part-6 of this code. Details of the uses of timber in structures or elements of structures including terminology,
material requirements, moisture content preferred cut sizes of sawn timbers, grading, permissible defects,
suitability in respect of durability and treatability, design criteria, and details of joints are also given in Chapter 11
of Part 6. Timber and timber constructions shall satisfy the requirements of that chapter and conform to the
following standards :
BDS 142: 1961 Specification for Wood Doors (under revision);
BDS 173: 1962 Specification for Wood Windows (under revision);
BDS 230: 1962 Glossary of Terms Applicable to Timber, Plywood and Joinery
(under revision);
BDS 803:1973 Trade Names and Abbreviated Symbols for Timber Species;
BDS 819:1975 Code of Practice for Preservation of Timber;
BDS 820:1978 Recommendation for Maximum Permissible Moisture Content
of Timber used for Different Purposes in Bangladesh;
BDS 857:1977 Specification for Grading Rules for Logs and Sawn Timbers;
BDS 1090:1984 Methods of Test for Plywood;
BDS 1256:1990 Classification of Commercial Timber;
BDS 1311:1990 Key for Identification of Commercial Timber.
2.9.2 Plywood
A wood structural panel comprised of plies of wood veneer arranged in cross-aligned layers. The plies are bonded
with waterproof adhesive that cures on application of heat and pressure.
Plywood shall conform to the following standards:
BDS 799:1983 Specification for Plywood for General Purposes (First Revision);
BDS 1158:1986 Specification for Veneered Decorative Plywood;
For sampling and testing of Plywood, the following Bangladesh Standards are applicable :
BDS 1087:1984 Specification for Method of Sampling of Plywood :
BDS 1090 : 1984 Methods of Test of Plywood.
IS 4990-1993 Specification for plywood for concrete shattering work (second
revision);

IS 5509-2000 Specification for fire retardant plywood (second revision);
IS 5539-1969 Specification for Preservative Treated Plywood.
2.9.3 Particle Boards and Fibre Boards
A panel primarily composed of cellulosic materials (usually wood), generally in the form of discrete pieces or
particles, as distinguished from fibers. The cellulosic material is combined with synthetic resin or other suitable
bonding system by a process in which the interparticle bond is created by the bonding system under heat and
pressure.
Fiber boards are fibrous, homogeneous panel made from lignocellulosic fibers (usually wood or cane) and having
a density of less than 497 kg per cubic meter but more than 160 kg per cubic meter.
These materials shall conform to the following standards:
BDS 619:1967 Specification for Particle Board (medium density) (under
revision);
BDS 620:1967 Specification for Hardboard (under revision);
BDS EN 316:2008 Wood Fiberboards Definition, Classification and Symbols
ISO 820:1975 Particle BoardsDefinition and Classification
ISO 821-1975 Particle BoardsDetermination of Dimensions of Test Pieces;
ISO 822:1975 Particle BoardsDetermination of Density;
ISO 823:1975 Particle BoardsDetermination of Moisture Content;
ISO 766: 1972 Fibre Building BoardsDetermination of Dimensions of Test
Pieces;
ISO 767:1975 Fibre Building BoardsDetermination of Moisture Content;
ISO 768:1972 Fibre Building BoardsDetermination of Bending Strength;
ISO 769:1972 Fibre Building BoardsHard and Medium BoardsDetermination
of
Water Absorption and of Swelling in Thickness after Immersion in Water;
ISO 818:1975 Fibre Building BoardsDefinition-Classification;
ISO 819:1975 Fibre Building Boards Determination of Density;
ISO 2695:1976 Fibre Building BoardsHard and Medium Boards for General
Purposes-Quality Specifications-Appearance, Shape and Dimensional Tolerances;
ISO 2696:1976 Fibre Building Boards-Hard and Medium Boards-Quality
Part 5
Building Materials

5-42 Vol. 2
Specifications- Water Absorption and Swelling in Thickness;
ISO 3340:1976 Fibre Building Boards-Determination of Sand Content;
ISO 3346:1976 Fibre Building Boards-Determination of Surface Finish
(roughness);
ISO 3729:1976 Fibre Building Boards-Determination of Surface Stability;
ISO/TR 7469:1981 Dimensional Stability of Hardboards.
Wood based Laminates
Laminated boards having a core of strips, each not exceeding 7 mm in thickness, glued together face to face to
form a slab which in turn is glued between two or more veneers, with the direction of the grainof the core strips
running at right angles to that of the adjacent outer veneers.
Wood based laminates shall conform to the following standards :
IS 3513:1989 Specification for resin treated compressed wood laminates
(compregs):
Part 3 For general purposes (first revision)
IS 3513:1966 Specification for resin treated compressed wood laminates
(compregs):
Part 4 Sampling and Tests
IS 9307-1979
(Parts I to VIII)
Methods of Tests for Wood-based Structural Sandwich
Construction.
Part I Flexure Test
Part II Edgewise Compression Test
Part III Flatwise Compression Test
Part IV Shear Test
Part V Flatwise Tension Test
Part VI Flexure Creep Test
Part VII Cantilever Vibration Test
Part VIII Weathering Test
2.9.4 Adhesives and Glues
Adhesives and glues are used to join two or more parts so as to form a single unit.
Adhesives shall conform to the following standards :

IS 848-1974 Specification for Synthetic Resign Adhesives for Plywood
(Phenolic and aminoplastic) (First Revision);
IS 849-1994 Specification for cold setting case in glue for wood (first revision)
IS 851-1978 Specification for Synthetic Resin Adhesives for Construction
Work (non structural) in Wood (First Revision);
IS 852-1994 Specification for animal glue for general wood-working purposes
(second revision);
IS 4835-1979 Specification for Polyvinyl Acetate Dispersion-based Adhesives
for Wood (First Revision);
IS 9188-1979 Specification for Adhesive for Structural Laminated Wood
Products for Use Under Exterior Exposure Condition.

2.10 DOORS, WINDOWS AND VENTILATORS
2.10.1 Wooden Doors, Windows and Ventilators
These shall conform to the following standards:
BDS 142:1961 Specification for Wood Door (under revision);
BDS 173:1962

Specification for Wood Windows (under revision);
BDS 820:1978 Recommendation for Maximum Permissible Moisture Content of
Timber Used for Different Purposes in Bangladesh;
BDS 1504:1996 Timber door window and ventilator frames
IS 1003-2003/1994 Specification for Timber Panelled and Glazed Shutters;
Part 1-2003 Door Shutters (Fourth Revision);
Part 2-1994 Window and Ventilator Shutters (Second Revision);
IS 1826-1961 Specification for Venetian Blinds for Windows;
IS 2191-1983

Specification for Wooden Flush Door Shutters (cellular and
hollow core type);
Part 1 Plywood Face Panels (Fourth Revision);
Part 2 Particle Board Face Panels and Hardboard Face Panels
(Third Revision);
Part 5
Building Materials

5-44 Vol. 2
IS 2202-1991/83

Specification for Wooden Flush Door Shutters (solid core type);
Part 1 Plywood Face Panels (Fifth Revision);
Part 2 Particle Board Face Panels and Hardboard Face Panels
(Third Revision);
IS 4020-1998 Method of tests for door shutters:
(Part 1): 1998 General (third revision)
(Part 2): 1998 Measurement of dimensions and squareness (
Third revision)
(Part 3): 1998 Measurement of general flatness (third revision)
(Part 4): 1998 Local planeness test (third revision)
(Part 5): 1998 Impact indentation test (third revision)
(Part 6): 1998 Flexure test (third revision)

(Part 7): 1998 Edge loading test (third revision)
(Part 8): 1998 Shock resistance test (third revision)
(Part 9): 1998 Buckling resistance test (third revision)
(Part 10) :1998 Slamming test (third revision)
(Part 11) :1998 Misuse test (third revision)
(Part 12) :1998 Varying humidity test (third revision)
(Part 13) :1998 End immersion test (third revision)
(Part 14) :1998 Knife test (third revision)
(Part 15) :1998 Glue adhesion test (third revision)
(Part 16) :1998 Screw withdrawal resistance test (third revision)
IS 4021:1995 Specification for timber door, window and ventilator frames
IS 4962:1968 Specification for wooden side sliding doors
IS 6198:1992 Specification for ledged, braced and battened timber shutters
(second revision)Revision);

2.10.2 Metal Doors, Windows Frames and Ventilators
These shall conform to the following standards :
BDS 1270: 1990 Specification for Strong Room Door;
BDS 1273: 1990 Specification for Vault Doors;
IS 1038-1983 Specification for Steel Doors, Windows and Ventilators (Third
Revision);
IS 1361-1978 Specification for Steel Windows for Industrial Buildings (First
Revision);
IS 1948-1961 Specification for Aluminium Doors, Windows and Ventilators;
IS 1949-1961 Specification for Aluminium Windows for Industrial Buildings;
IS 4351-2003 Specification for Steel Door Frames (Second Revision);
IS 6248-1979 Specification for Metal Rolling Shutters and Rolling Grills (First
Revision);
IS 7452-1990 Specification for Hot Rolled Steel Sections for Doors, Windows
and Ventilators (Second Revision);
IS 10451-1983 Specification for Steel Sliding Shutters (top hung type);
IS 10521-1983 Specification for Collapsible Gates;
2.10.3 Plastic Doors and Windows
These shall conform to the following standards :
BDS EN 477: 2008 Unplasticized polyvinylchloride (PVC - U) profiles for the
fabrication of windows and doors Determination of the
resistance to impact of main profiles by falling mass
fabrication of windows and doors Determination of
appearance after exposure at 150 C
fabrication of windows and doors Determination of heat
reversion
resistance to artificial weathering
BDS EN 514: 2008

Unplasticized polyvinylchloride (PVC - U) profiles for the
Part 5
Building Materials

5-46 Vol. 2
strength of welded corners and T-joints
BDS EN 12608: 2008

Unplasticized polyvinylchloride (PVC - U) profiles for the
fabrication of windows and doors Classification, requirements
and test methods
BDS ISO 1163-1:2008 Plastics Unplasticized poly (vinyl chloride) (PVC - U) moulding
and extrusion materials Part 1: Designation system and basis
for specifications
BDS ISO 1163-2:2008 Plastics Unplasticized poly (vinyl chloride) (PVC - U) moulding
and extrusion materials Part 2: Preparation of test specimens
and determination of properties
IS 14856:2000 Specification for glass fibre reinforced (GRP) panel type door
shutters for internal use
IS 15380:2003 Specification for moulded raised high density fibre (HDF) panel
doors
2.11 ALUMINIUM AND ALUMINIUM ALLOYS
Aluminum used for structural purposes in buildings and structures shall comply with AA ASM 35 and AA ADM 1.
Aluminium and Aluminium Alloys shall also conform to the following standards:
BDS EN 755-9:2010 Aluminium and aluminium alloys Extruded rod/bar, tube and
profiles Part 9: Profiles, tolerances on dimensions and form
profiles Part 2: Mechanical properties
profiles Part 1: Technical conditions for inspection and
delivery
profiles Part 3: Round bars, tolerances on dimensions and
form
profiles Part 4: Square bars, tolerances on dimensions and
form
profiles Part 5: Rectangular bars, tolerances on dimensions
and form
profiles Part 6: Hexagonal bars, tolerances on dimensions and

form
profiles Part 7: Seamless tubes, tolerances on dimensions
and form
profiles Part 8: Porthole tubes, tolerances on dimensions and
form
BDS EN 12020-1:2010 Aluminium and aluminium alloys Extruded precision profiles
in alloys EN AW-6060 and EN AW-6063 Part 1: Technical
conditions for inspection and delivery
BDS EN 12020-2:2010 Aluminium and aluminium alloys Extruded precision profiles
in alloys EN AW-6060 and EN AW-6063 Part 2: Tolerances on
dimensions and form
BDS EN 515:2010 Aluminium and aluminium alloys Wrought products
Temper designations
ASTM B26 / B26M - 09 Standard Specification for Aluminum-Alloy Sand Castings
ASTM B85 / B85M - 09 Standard Specification for Aluminum-Alloy Die Castings
ASTM B108 / B108M - 08 Standard Specification for Aluminum-Alloy Permanent Mold
Castings
ASTM B209 - 07 Standard Specification for Aluminum and Aluminum-Alloy Sheet
and Plate
ASTM B210 - 04 Standard Specification for Aluminum and Aluminum-Alloy
Drawn Seamless Tubes
ASTM B211 - 03 Standard Specification for Aluminum and Aluminum-Alloy Bar,
Rod, and Wire
ASTM B221 - 08 Standard Specification for Aluminum and Aluminum-Alloy
Extruded Bars, Rods, Wire, Profiles, and Tubes
ASTM B241 / B241M - 02 Standard Specification for Aluminum and Aluminum-Alloy
Seamless Pipe and Seamless Extruded Tube
ASTM B308 / B308M - 02 Standard Specification for Aluminum-Alloy 6061-T6 Standard
Structural Profiles
Round Welded Tubes
ASTM B316 / B316M - 02 Standard Specification for Aluminum and Aluminum-Alloy Rivet
and Cold-Heading Wire and Rods
Part 5
Building Materials

5-48 Vol. 2
ASTM B429 / B429M - 06 Standard Specification for Aluminum-Alloy Extruded Structural
Pipe and Tube
Drawn Tube and Pipe for General Purpose Applications
Formed and Arc-Welded Round Tube
ASTM B632 / B632M - 08 Standard Specification for Aluminum-Alloy Rolled Tread Plate
ASTM B745 / B745M -
97(2005)
Standard Specification for Corrugated Aluminum Pipe for
Sewers and Drains
ASTM E34 - 94(2002) Standard Test Methods for Chemical Analysis of Aluminum and
Aluminum-Base Alloys
2.12 BUILDERS HARDWARE
The applicable standards are listed below :
BDS 113:1986 Specification for Latches and Locks for Doors in Buildings;
IS 204-1991/1992 Specification for Tower Bolts;

Part 1 Ferrous Metals (Fifth Revision);

Part 2 Nonferrous metals (Fifth Revision);
IS 205-1992 Specification for Nonferrous Metal Butt Hinges (fourth
Revision);
IS 206-1992 Specification for Tee and Strap Hinges (Fourth Revision);
IS 208-1996 Specification for Door Handles (Fifth Revision);
IS 281-1991 Specification for Mild Steel Sliding Door Bolts for Use with
Padlock (Third Revision);
IS 362-1991 Specification for Parliament Hinges (Fifth Revision);
IS 363-1993 Specification for Hasps and Staples (Fourth Revision);
IS 364-1993 Specification for Fanlight Catch (Third Revision);
IS 452-1973 Specification for Door Springs, Rat-tail Type (Second Revision);
IS 453-1993 Specification for Double Acting Spring Hinges (Third Revision);
IS 729-1979 Specification for Drawer Locks, Cupboard Locks and Box Locks
(Third Revision);

IS 1019-1974 Specification for Rim Latches (Second Revision);
IS 1341-1992 Specification for Steel Butt Hinges (Sixth Revision);
IS 1823-1980 Specification for Floor Door Stoppers (Third Revision);
IS 1837-1966 Specification for Fanlight Pivots (First Revision);
IS 2209-1976 Specification for Mortice Locks (vertical type) (Third Revision);
IS 2681-1993 Specification for Nonferrous Metal Sliding Door Bolts for Use
with Padlocks (Third Revision);
IS 3564-1995 Specification for Door Closers (hydraulically regulated) (Second
Revision);
IS 3818-1992 Specification for Continuous (piano) Hinges (Third Revision);
IS 3828-1966 Specification for Ventilator Chains;
IS 3843-1995 Specification for Steel Backflap Hinges; (First Revision)
IS 3847-1992 Specification for Mortice Night Latches; (First Revision)
IS 4621-1975 Specification for Indicating Bolts for use in Public Baths and
Lavatories (First Revision);
IS 4948-2002 Specification for Welded Steel Wire Fabric for General Use
(Second Revision);
IS 4992-1975 Specification for Door Handles for Mortice Locks (vertical type)
(First Revision);
IS 5187-1972 Specification for Flush Bolts (First Revision);
IS 5899-1970 Specification for Bathroom Latches;
IS 5930-1970 Specification for Mortice Latch (vertical type);
IS 6315-1971 Specification for Floor Springs (hydraulically regulated) for
Heavy Doors;
IS 6318-1971 Specification for Plastic Window Stays and Fasteners;
IS 6343-1982 Specification for Door Closers (pneumatically regulated) for
Light Doors Weighing up to 40 kg (First Revision);
IS 6602-1972 Specification for Ventilator Poles;
IS 6607-1972 Specification for Rebated Mortice Locks (vertical type);
IS 7196-1974 Specification for Hold Fast;
Part 5
Building Materials

5-50 Vol. 2
IS 7197-1974

Specification for Double Action Floor Springs (without oil check)
for Heavy Doors;
IS 7534-1985 Specification for sliding locking bolts for use with padlocks (first
revision);
IS 7540-1974 Specification for Mortice Dead Locks;
IS 8756-1978 Specification for Ball Catches for use in Wooden Almirah;
IS 8760-1978 Specification for Mortice Sliding Door Locks, with Lever
Mechanism;
IS 9106-1979 Specification for Rising Butt Hinges;
IS 9131-1979 Specification for Rim Locks;
IS 9460-1980 Specification Flush Drop Handle for Drawer;
IS 9899-1981 Specification for Hat, Coat and Wardrobe Hooks;
IS 10019-1981 Specification for Steel Window Stays and Fasteners;
IS 10090-1982 Specification for Numericals;
IS 10342-1982 Specification for Curtain Rail System
IS 12817:1997 Specification for stainless steel butt hinges (first revision)
IS 12867:1989 Specification for PVC hand rails covers
IS 14912:2001 Specification for door closers concealed type (hydraulically
regulated)
2.13 ROOF COVERINGS
2.13.1 Scope
The provisions of this section shall govern the materials used for roof coverings.
2.13.2 Compatibility of Materials
All roofs and roof coverings shall be of materials that are compatible with each other and with the building or
structure to which the materials are applied.
2.13.3 Material Specifications and Physical Characteristics
All materials to be used in the construction of roofs and roof coverings shall conform to the applicable standards
listed in this section. In the absence of applicable standards or when materials are of questionable suitability,
testing by an approved testing agency may be required by the building official to determine the character, quality
and limitations of use of the materials.

2.13.4 Weather Protection
All roofs shall be covered with approved roof coverings properly secured to the building or structure to resist wind
and rain. Roof coverings shall be designed, installed and maintained in accordance with approved manufacturer's
recommendations such that the roof covering shall serve to protect the building or structure.
2.13.5 Wind Resistance
All roofs and roof coverings shall be secured in place to the building or structure to withstand the wind loads.
2.13.6 Structural and Construction Loads
The structural roof components shall be capable of supporting the roof covering system and the material and
equipment loads that will be encountered during installation of the roof covering system.
2.13.7 Impact Resistance
Roof coverings shall resist impact damage based on the results of tests conducted in accordance with
ASTMD4272 - 09 or D3746 - 85(2008).
2.13.8 Metal-Sheet Roof Coverings
Metal-sheet roof coverings installed over structural framing and decking shall comply with BDS 868, Galvanized
Corrugated Sheet Roof and Wall Coverings; BDS 1122, Hot-dip Galvainzed Steel Sheet and Coil; ASTMA755 /
A755M - 03(2008) or B101 - 07. Metal-sheet roof coverings shall be installed in accordance with approved
manufacturer's installation instructions.
2.13.9 Asbestos Sheet Roof Covering
Asbestos sheets used for roof coverings shall comply with BDS 430, Asbestos Cement Corrugated Sheets for
Roofing and Cladding; BDS 431, Asymmetrical Section Corrugated Sheets in Asbestos Cement Roofing and
Cladding; BDS 579, Abestos Cement Flat Sheets; BDS 1046, Asbestos Cement Products-Corrugated Sheets and
Fittings for Roofing and Cladding.
2.13.10 Interlocking Clay or Cement Tile
Interlocking clay or cement tile shall be installed only over solid sheathing or spaced structural sheathing boards.
Interlocking clay or cement tile shall not be installed on roof slopes below one unit vertical in 3 units horizontal
(1:3). Horizontal battens shall be required on roof slopes over one unit vertical in 2 units horizontal (1:2). Single
layer underlayment is required over solid sheathing on all roof slopes. Reinforced underlayment shall be required
when spaced sheathing is used. Regardless of roof slope, the first three tile courses and all tiles within 900 mm of
roof edges, tiles at changes in roof slope or changes in slope direction, shall be fastened to the roof. For the field
of the roof, fastening is not required on roof slopes below one unit vertical in 2 units horizontal (1:2). Every other
tile course shall be fastened on roof slopes 1:2 to less than 1:1; and every tile shall be fastened on roof slopes 1:1
and over. Tile overlap shall be in accordance with approved manufacturer's installation instructions.
2.13.11 Non-interlocking Clay or Cement Tile
Non-interlocking clay or cement tile shall not be installed on roof slopes below one unit vertical in 5 units
horizontal (1:5). Double layer underlayment is required on roof slopes below one unit vertical in 4 units horizontal
(1:4). Single layer underlayment is required on all other roof slopes. Non-interlocking clay or cement tile shall be
secured to the roof with two fasteners per tile. The minimum tile overlap shall be 75 mm.
Part 5
Building Materials

5-52 Vol. 2
2.13.12 Roof Insulation
Rigid combustible roof insulation shall be permitted, provided the insulation is covered with approved roof
coverings directly applied thereto. Insitu lime concrete may be used on flat roofs of buildings. Minimum
compacted thickness of such a layer shall be 75 mm and have adequate slope for drainage. The materials used in
lime concrete shall conform to the standards specified in Sec 2.5 of this Part.
2.13.13 Recovering and Replacement of Roof Coverings
New roof coverings shall not be installed without first removing existing roof coverings when the existing roof or
roof covering is water soaked or has deteriorated to the point that the existing roof or roof covering is not
acceptable as a base for additional roofing.
2.13.14 Reuse of Materials
Existing slate, clay or cement tile shall be permitted for reuse, except that damaged, cracked or broken slate or
tile shall not be reused. Existing vent flashings, metal edgings, drain outlets, collars and metal counter flashings
shall not be reused where rusted, damaged or deteriorated. Aggregate surfacing materials shall not be reused.
2.13.15 Applicable Standards
The applicable standards for materials used in roofs and roof coverings are listed below:
BDS 430:1964

Specification for Asbestos Cement Corrugated Sheets for
Roofing and Cladding
BDS 431:1964 Specification for Asymmetrical Section Corrugated Sheets in
Asbestos Cement for Roofing and Cladding
BDS 579:1966 Specification for Asbestos Cement Flat Sheets (under revision);
BDS 868:1978 Code of Practice for Galvanized Corrugated Sheet Roof and Wall
Coverings;
BDS 1046:1983 Specification for Asbestos Cement Products - Corrugated Sheets
and Fittings for Roofing and Cladding;
BDS 1122:1985 Specification for Hot-dip Galvanized Steel and Coil.
BDS EN 490: 2008 Concrete roofing tiles and fittings for roof covering and all
cladding Product specifications
BDS EN 49l: 2008 Concrete roofing tiles and fittings for roof covering and wall
cladding Test methods
BDS EN 538: 2008

Clay roofing tiles for discontinuous laying Flexural strength
test
BDS EN 539-l: 2008 Clay roofing tiles for discontinuous laying Determination of
physical characteristics Part 1: Impermeability test
BDS EN 1024: 2008 Clay roofing tiles for discontinuous laying Determination of
geometric characteristics

BDS EN 1304: 2008 Clay roofing tiles and fittings Product definitions and
specifications
ASTM A755 / A755M -
03(2008)

Standard Specification for Steel Sheet, Metallic Coated by the
Hot-Dip Process and Pre-painted by the Coil-Coating Process for
Exterior Exposed Building Products
ASTM B101 - 07 Standard Specification for Lead-Coated Copper Sheet and Strip
for Building Construction
ASTM C222 - 97(2008) Standard Specification for Asbestos-Cement Roofing Shingles
ASTM C406 - 06e1 Standard Specification for Roofing Slate
ASTM C836 / C836M - 10 Standard Specification for High Solids Content, Cold Liquid-
Applied Elastomeric Waterproofing Membrane for Use with
Separate Wearing Course
ASTM C1029 - 09 Standard Specification for Spray-Applied Rigid Cellular
Polyurethane Thermal Insulation
ASTM D6380 - 03(2009) Standard Specification for Asphalt Roll Roofing (Organic Felt)
ASTM D225 - 07 Standard Specification for Asphalt Shingles (Organic Felt)
Surfaced With Mineral Granules
ASTM D226 / D226M - 09 Standard Specification for Asphalt-Saturated Organic Felt Used
in Roofing and Waterproofing
ASTM D227 - 03 Standard Specification for Coal-Tar-Saturated Organic Felt Used
ASTM D6380 - 03(2009) Standard Specification for Asphalt Roll Roofing (Organic Felt)
ASTM D312 - 00(2006) Standard Specification for Asphalt Used in Roofing
ASTM D450 - 07 Standard Specification for Coal-Tar Pitch Used in Roofing,
Dampproofing, and Waterproofing
ASTM D1227 - 95(2007) Standard Specification for Emulsified Asphalt Used as a
Protective Coating for Roofing
ASTM D1863 - 05 Standard Specification for Mineral Aggregate Used on Built-Up
Roofs
ASTM D2178 - 04 Standard Specification for Asphalt Glass Felt Used in Roofing
and Waterproofing
ASTM D2626 - 04 Standard Specification for Asphalt-Saturated and Coated
Organic Felt Base Sheet Used in Roofing
Part 5
Building Materials

5-54 Vol. 2
ASTM D2898 - 10 Standard Practice for Accelerated Weathering of Fire-
Retardant-Treated Wood for Fire Testing
ASTM D3161 - 09 Standard Test Method for Wind-Resistance of Asphalt Shingles
(Fan-Induced Method)
ASTM D4897 / D4897M -
01(2009)
Standard Specification for Asphalt-Coated Glass-Fiber Venting
Base Sheet Used in Roofing
ASTM D3747 - 79(2007) Standard Specification for Emulsified Asphalt Adhesive for
Adhering Roof Insulation
ASTM D3909 -
97b(2004)e1
Standard Specification for Asphalt Roll Roofing (Glass Felt)
Surfaced With Mineral Granules
ASTM D4272 - 09 Standard Test Method for Total Energy Impact of Plastic Films
By Dart Drop
ASTM D4434 / D4434M -
09
Standard Specification for Poly(Vinyl Chloride) Sheet Roofing
ASTM D4601 - 04 Standard Specification for Asphalt-Coated Glass Fiber Base
Sheet Used in Roofing
ASTM D4637 - 08

Standard Specification for EPDM Sheet Used In Single-Ply Roof
Membrane
ASTM E108 - 10a Standard Test Methods for Fire Tests of Roof Coverings
ASTM G90 - 05 Standard Practice for Performing Accelerated Outdoor
Weathering of Nonmetallic Materials Using Concentrated
Natural Sunlight
ASTM G155 - 05a Standard Practice for Operating Xenon Arc Light Apparatus for
Exposure of Non-Metallic Materials
ASTM G154 - 06 Standard Practice for Operating Fluorescent Light Apparatus for
UV Exposure of Nonmetallic Materials
RMA (Rubber
Manufacturer
Association, USA) RP - 4 -
88
Wind Design Guide for Ballasted Single-Ply Roofing Systems;
SPRI (Single Ply Roofing
Institute, USA) - 86
Wind Design Guide for Ballasted Single-Ply Roofing Systems;
FM ( Factory Manual)
4450 - 89

Standard Laboratories Department Approved Standard for Class
I Insulated Steel Deck Roofs;

FM 447 -86 Approval Standard for Class I Roof Coverings;
CGSB (Canadian General
Standards Board) 37 - GP
- 56M - 80
Membrane, Modified Bituminous, Prefabricated, and
Reinforced for Roofing;
2.14 PAINTS AND VARNISHES
2.14.1 Water Based Paints and Pigments
Water based paints shall conform to the following standards:
BDS 500:1965 Specification for Distemper Dry (under revision);
BDS 1097:1984 Specification for Plastic Emulsion Paint.
Part I for Interior Use;
Part 2 for Exterior Use;
IS 427:1965 Specification for distemper, dry, colour as required (revised)
IS 428:2000 Specification for distemper, washable (second revision)
IS 5410:1992 Specification for cement paint, colour as required (first revision)
IS 5411 Specification for plastic emulsion paint:
(Part 1):1974 For interior use(first revision)
(Part 2): 1972 For exterior use
2.14.2 Ready Mixed Paints, Enamels and Powder Coatings
Ready mixed paints and enamels shall conform to the following standards:
BDS 13:1960 Specification for Ready Mixed Paints, Varnish, Lacquers and
Related Products (under revision);
BDS 14:1960

Specification for Black Bituminous Paint, Brushing for General
Purposes (under revision);
BDS 397:1964

Specification for Ready Mixed Paint, Brushing, Red Oxide Zinc
Chrome, Priming (under revision);
BDS 398:1964 Specification for Ready Mixed Paint, Spraying, Red Oxide Zinc
Chrome, Priming (under revision);
BDS 399:1964 Specification for Aluminum Paint, Spraying for General
Purposes, in Dual Container (under revision);
Part 5
Building Materials

5-56 Vol. 2
BDS 400:1964 Specification for Aluminium Paint, Brushing, for General
Purposes in Dual Container (under revision);
BDS 401:1964

Specification for Varnish, Finishing, Exterior, Type-I, (Synthetic)
(Tentative) (under revision);
BDS 402:1989 Specification for Ready Mixed Paint, Brushing, Finishing,
Semigloss, for General Purposes (First Revision);
BDS 499:1965 Specification for Ready Mixed Paints, Brushing, for Road
Marking (white, yellow and black) (under revision);
BDS 616:1966 Specification for Enamel, Brushing, Exterior (i) Undercoating, (ii)
Finishing, Colour as Required (under revision);
BDS 617:1966

Specification for Enamel, Brushing, Interior (i) Undercoating, (ii)
Finishing, Colour as Required (under revision);
BDS 926:1980 Specification for Ready Mixed Paint, Brushing, Petrol Resisting,
Air Drying, for Exterior Painting of Containers, Colour as
Required;
BDS 927:1980

Specification for Ready Mixed Paint, Brushing, Petrol Resisting,
Air Drying, for Interior Painting of Tanks and Containers, Red
Oxide (colour unspecified);
BDS 928:1980 Specification for Ready Mixed Paint, Brushing, Acid Resisting, for
Protection Against Acid Fumes, Colour as Required;
BDS 973:1981

Specification for Specification and Methods of Test for Linseed
Stand Oil for Paints and Varnishes;
BDS 974:1981 Specification and Methods of Test for Raw Tung Oils for Paints
and Varnishes;
BDS 1005:1981 Specification for Ready Mixed Paint, Brushing, Finishing, Stoving,
Enamel, Colour as Required;
BDS 1141:1986 Specification for Ready Mixed Aluminium Priming Paints for
Woodwork;
BDS 1151:1986 Specification for Pavement Marking Paints.
IS 101 Methods of sampling and test for paints, varnishes and related
products:
(Part l/See 1):1986 Test on liquid paints (general and
physical), Section 1 Sampling (third revision)

physical), Section 2 Preliminary examination and preparation of
samples for testing (third revision)
physical), Section 3 Preparation of panels (third revision)
(Part l/See 4) :1987 Test on liquid paints (general and
physical), Section 4 Brushing test (third revision)
physical), Section 5 Consistency (third revision)
physical), Section 6 Flash point (third revision)
physical), Section 7 Mass per 10 Iitres (third revision)
(Part 2/See 1):1988 Test on liquid paints (chemical
examination), Section 1 Water content (third revision)
(Part 2/See 2):1986 Test on liquid paints (chemical
examination), Section 2 Volatile matter (third revision)
(Part 3/See 1):1986 Tests on paint film formation, Section 1
Drying time (third revision)
Film thickness (third revision)
Finish (third revision)
Fineness of grind (third revision)
(Part 4/See 1):1988 Optical test, Section 1 Opacity (third
revision)
(Part 4/See 2):1989 Optical test, Section 2 Colour (third
revision)
(Part 4/See 3):1988 Optical test, Section 3 Light fastness
test (third revision)
(Part 4/See 4):1986 Optical test, Section 4 Gloss (third
revision)
(Part 5/See 1):1988 Mechanical test on paint films, Section
1 Hardness tests (third revision)
Part 5
Building Materials

5-58 Vol. 2
Part 5/See 2):1988 Mechanical test on paint films, Section
2 Flexibility and adhesion (third revision)
(Part 5/See 3):1986 Mechanical test on paint films, Section
3 Impact resistance (fourth revision)
(Part 5/See 4):1986 Mechanical test on paint films,
Section4 Print free test (third revision)
(Part 6/See 1):1988 Durability tests, Section 1 Resistance to
humidity under conditions of condensation (third revision)
(Part 6/See 2):1989 Durability tests, Section 2 Keeping
properties (third revision)
(Part 6/See 3):1990 Durability tests, Section 3 Moisture
vapour permeability (third revision)
(Part 6/See 4):1991 Durability tests, Section 4 Degradation
of coatings (pictorial aids for evaluation)
(Part 6/See 5):1997 Durability tests, Section 5 Accelerated
weathering test (third revision)
(Part 7/See 1) :1989 Environmental tests on paint films,
Section 1 Resistance to water (third revision)
(Part 7/See 2):1990 Environmental tests on paint films,
Section 2 Resistance to liquids (third revision)
Section 3 Resistance to heat (third revision)
Section 4 Resistance to bleeding of pigments (third revision)
(Part 8/See 1):1989 Tests for pigments and other solids,
Section 1 Residue on sieve (third revision)
Section 2 Pigments and nonvolatile matter (third revision)
Section 3 Ash content
Section 4 Phthalic anhydride
Section 5 Lead restriction test (third revision)

Section 6 Volume solids
(Part 9/See 1):1993 Tests for lacquers and varnish, Section 1
Acid value
(Part 9/See 2):1993 Tests for lacquers and varnish, Section 2
Rosin test
IS 104:1979 Specification for ready mixed paint, brushing, zinc chrome,
priming (second revision)
IS 109:1968 Specification for ready mixed paint, brushing, priming, plaster to
Indian Standard colours No. 361 and 631 (first revision)
IS 123:1962 Specification for ready mixed paint, brushing, finishing, semi-
gloss, for general purposes, to Indian Standard colours No. 445,
446, 448, 449, 451 and 473; and red oxide (colour unspecified)
(revised)
IS 133:1993 Specification for enamel, interior (a) undercoating, (b) finishing
(third revision)
IS 137:1965 Specification for ready mixed paint, brushing, matt or egg-shell
flat, finishing, interior, to Indian Standard colour, as required
(revised)
IS 158:1981 Specification for ready mixed paint, brushing, bituminous, black,
lead-free, acid, alkali, and heat resisting (third revision)
IS 168:1993 Specification for ready mixed paint, air-drying semi-glossy/matt,
for general purposes (third revision)
IS 341:1973 Specification for black Japan, Types A, B and C first revision)
IS 2074:1992 Specification for ready mixed paint, air drying red oxide-zinc
chrome, priming (second revision)
IS 2075:2000 Specification for ready mixed paint, stoving, red oxide-zinc
chrome, priming (second revision)
IS 2339:1963 Specification for aluminium paint for general purposes, in dual
container
IS 2932:2003 Specification for enamel, synthetic, exterior, (a) undercoating,
(b) finishing (third revision)
IS 2933:1975 Specification for enamel, exterior, (a) undercoating, (b) finishing
(first revision)
IS 3536:1999 Specification for ready mixed paint, brushing, wood primer
Part 5
Building Materials

5-60 Vol. 2
(first revision)
IS 3537:1966 Specification for ready mixed paint, finishing, interior for general
purposes, to Indian Standard colours No. 101, 216, 217, 219,
275:281, 352, 353, 358 to 361, 363,364,388,410,442, 444,628,
631,632,634,693,697, white andblack
IS 3539:1966 Specification for ready mixed paint, undercoating, for use under
oil finishes, to Indian Standard colours, as required
IS 3585:1966 Specification for ready mixed paint, aluminium, brushing,
priming, water resistant, for wood work
IS 3678:1966 Specification for ready mixed paint, thick white, for lettering
IS 8662:1993

Specification for enamel, synthetic, exterior, (a) undercoating,
(b) finishing, for railway coaches (first revision)
IS 9862:1981 Specification for ready mixed paint, brushing, bituminous black
lead free, acid, alkali, water and chlorine resisting
IS 11883:1986

Specification for ready mixed paint, brushing, red oxide, priming
for metals
IS 13183:1991 Specification for aluminium paints, heat resistant
IS 13213:1991 Specification for polyurethane full gloss enamel (two pack)
IS 13607:1992 Specification for ready mixed paint, finishing, general purposes,
synthetic
IS 13871:1993 Specification for powder coatings
2.14.3 Thinners and Solvents
IS 324-1959 Specification for Ordinary Denatured Spirit (revised);
IS 82:1992 Methods of sampling and test for thinners and solvents for
paints (first revision)
IS 324:1959 Specification for ordinary denatured spirit (revised)
IS 533:1998 Specification for gum spirit of turpentine (oil of turpentine)
(second revision)
IS 14314:1995 Specification for thinner general purposes for synthetic paints
and varnishes

2.14.4 Varnishes and Lacquers
BDS 401:1964

Specification for Varnish, Finishing, Exterior, Type-I, (synthetic)
(under revision);
BDS 1064:1983

Specification for Varnish, Stoving;
BDS 1065:1983 Specification for Varnish, Acid Resisting;
BDS 1066:1983 Specification for Varnish, Finishing, Interior;
IS 337:1975 Specification for varnish, finishing, interior (first revision)
IS 347-1975 Specification for Varnish, Shellac for general purposes (First
Revision);
IS 348-1968 Specification for French Polish (First Revision);
IS 524:1983 Specification for varnish, finishing, exterior, synthetic (second
revision)
IS 525:196 Specification for varnish, finishing, exterior and general purposes
(first revision)
IS 642:1963 Specification for varnish medium for aluminium paint (revised)
2.15 SANITARY APPLIANCES AND WATER FITTINGS
2.15.1 Sanitary Appliances
Sanitary appliances shall conform to the following standards:
BDS 1162 : 2006 (1st
revision)
Ceramic wash basin and pedestal, ceramic wash basin and
pedestals dimension, design & construction, type, permissible
deviation
BDS 1163 : 1987 Specification for Vitreous Sanitary Appliances,
Part-1, General Requirements;
Part-2, Specific Requirements for Water Closets;
Part-3, Specification Requirements for Urinal (Bowl type);
Part-4, Specific Requirements for Foot Rest;
Part-5, Specific Requirements for Integrated Squatting Pans.
BDS 1361:1992 Faucets
Part 5
Building Materials

5-62 Vol. 2
BDS 1593:1998 Plastic sanitary squatting pan
ASHRA E90A-80 Energy Conservation in New Building Design;
ASHRA E 90B-75

Energy Conservation in New Building Design;
C700-09: Cold-Water Meters--Displacement Type, Bronze Main Case;
C701-07: Cold-Water Meters -- Turbine Type, for Customer Service;
C702-01: Cold-Water Meters -- Compound Type;
BS 1125: 1987 Specification for WC Flushing Cisterns (Including Dual Flash Cisterns
and Flush Pipes);
BS 1244 Metal Sink for Domestic Purposes;
BS 1254:1981 Specification for C Seats (Plastics);
BS 1329:1974 Specification for Metal Hand Rinse Basins;
BS 1876:
1992(1977)
Specification for Automatic Flushing Cistern for Urinals
2.15.2 Pipes and Pipe Fittings for Water Supply and Sanitation
Pipes and pipe fittings for water supply and sanitation shall comply with the following standards.
BDS 428:1964 Specification for Asbestos Cement Pressure Pipe;
BDS 429:1964 Specification for Asbestos Cement Building and Sanitary Pipes
(under revision);
BDS 1111:1984 Centrifugally Cast (spun) Iron Pressure Pipes for Water, Gas and
Sewage;
BDS 1356:1992 Specification for Ferrules for Water Services;
BDS 1357: 1992 Specification for Washers with Fittings for Water Service;
BDS 1361 : 1992 Faucets
This standard specifies the technical requirements of various
types of Faucets.
BDS 1562:1997 Solvent cements for polyvinyl chloride (PVC) plastic pipe and
fitting.
BDS 1593 : 1998 Plastic sanitary squatting pan
Pan lays down the requirement for material, dimension physical

requirements and testing for power flush type injection moulded
high density polyethylene (HDPE) or polypropylene (PP)
squatting pan.
BDS EN 1254-2: 2009 Copper and copper alloys - Plumbing fittings Part 2: Fittings
with compression ends for use with copper tubes
BDS EN 1717: 2009 Protection against pollution of potable water in water
installations and general requirements of devices to prevent
pollution by backflow
BDS EN 14506: 2009 Devices to prevent pollution by backflow of potable water
Automatic diverter Family H, type C
BDS ISO 3419: 2008 Non alloy and alloy steel buttwelding fittings
BDS ISO 5251: 2008 Stainless steel buttwelding fittings
BDS ISO 6761: 2008 Steel tubes Preparation of ends of tubes and fittings for
welding
BDS ISO 3822--1: 2009 Acoustics: Laboratory tests on noise emission from appliances
and equipment used in water supply installations Part 1:
Method of measurement
BDS ISO 3822--2: 2009

Acoustics: Laboratory tests on noise emission from appliances
Mounting and operating conditions for draw-off taps and mixing
valves
BDS ISO 3822--4: 2009 Acoustics: Laboratory tests on noise emission from appliances
Mounting and operating conditions for special appliances
BDS ISO 161-1 : 2008 Thermoplastics pipes for the conveyance of fluids Nominal
outside diameters and Nominal Pressures- Part 1: Metric series
BDS ISO 161-2 : 2008 Thermoplastics pipes for the conveyance of fluids- Nominal
outside diameters and Nominal Pressures- Part 2: Inch based
series
BDS ISO 265-1 : 2008 Pipes and fittings of plastics materials- fittings for domestic and
industrial waste pipes- Basic dimensions: Metric series- Part 1:
Unplasticized Poly (Vinyl chloride) (PVC-U)
BDS ISO 1167-1 : 2008 Thermoplastics pipes fittings and assemblies for the conveyance
of fluids - Determination of the resistance to internal pressure-
Part 1: General method
BDS ISO 1167-2 : 2008 Thermoplastics pipes fittings and assemblies for the conveyance
of fluids- Determination of the resistance to internal pressure-
Part 5
Building Materials

5-64 Vol. 2
Part 2: Preparation of pipe test pieces
BDS ISO 1746 : 2008 Rubber or Plastics hoses and tubing-Bending tests
BDS ISO 2505 : 2008 Thermoplastics pipes- Longitudinal reversion Test method and
parameters
BDS ISO 2507-2 : 2008

Thermoplastics pipes and fittings Vicat softening temperature-
Part 2: Test conditions for Unplasticized poly (Vinyl chloride)
(PVC-U) or chlorinated poly (Vinyl chloride) (PVC-C) pipes and
fittings and for high impact resistance poly (Vinyl chloride) (PVC-
HI) pipes
BDS ISO 3114: 2008 Unplasticized polyvinyl chloride (PVC) pipes for potable water
supply-Extractability of lead and tin- Test method
BDS ISO 3126 : 2008 Plastics piping systems-Plastics components- Determination of
dimensions
BDS ISO 3127: 2008

Thermoplastics pipes- Determination of resistance to external
blows-Round the - clock method
BDS ISO 3501:2010 Assembled joints between fittings and polyethylene (PE)
pressure pipes Test of resistance to pull-out
pressure pipes Test of leakproofness under internal pressure
when subjected to bending
BDS ISO 3633: 2008 Plastics piping systems for soil and waste discharge (Low and
high temperature ) inside buildings- Specifications
BDS ISO 6964:2010 Polyolefin pipes and fittings Determination of carbon black
content by calcination and pyrolysis Test method and basic
specification
BDS ISO 4065: 2008 Thermoplastics pipes- Universal wall thickness table
BDS ISO /TR 4191: 2008 Unplasticized polyvinyl chloride (PVC-U) pipes for water supply-
Recommended practice for laying
BDS ISO 4422-1: 2008 Pipes and fittings made of unplasticized poly (vinyl chloride)
(PVC-U) for water supply - Specifications - Part 1: General
(PVC-U) for water supply - Specifications - Part 2: Pipes (with or
without integral sockets)
BDS ISO 4422-3: 2008 Pipes and fittings made of unplasticized poly (vinyl chloride)(PVC-
U) for water supply- Specifications - Part 3: Fittings and joints

(PVC-U) for water supply- Specifications- Part 4: Valves and
ancillary equipment
(PVC- U) for water supply- Specifications- Part 5: Fitness for
purpose of the system
BDS ISO 4433-3: 2008 Thermoplastics pipes- Resistance to liquid chemicals-
Classification-Part 3: Unplasticized poly (vinyl chloride) (PVC-U),
high- impact poly (vinyl chloride) (PVC-HI) and chlorinated poly
(vinyl chloride) (PVC C) pipes
BDS ISO 4435: 2008

Plastic piping systems for nonpressure underground drainage
and sewerage- Unplasticized poly (vinyl chloride) (PVC-U)
BDS ISO 4439: 2008 Unplasticized polyvinyl chloride (PVC) pipes and fittings
Determination and specification of density
BDS ISO 6259-1: 2008 Thermoplastics pipes- Determination of tensile properties- Part
1: General test method
BDS ISO 6259-2: 2008 Thermoplastics pipes- Determination of tensile properties- Part
2: Pipes made of unplasticized poly (vinyl chloride) (PVC-U),
Chlorinated poly (vinyl chloride) (PVC-C), and high impact poly
(vinyl chloride) (PVC-HI)
BDS ISO 6992: 2008

Unplasticized polyvinyl chloride (PVC-U) pipes for drinking
water supply - Extractability of cadmium and mercury occurring
as impurities
BDS ISO 9624:2010 Thermoplastics pipes for fluids under pressure Mating
dimensions of flange adapters and loose backing flanges
BDS ISO 11413:2010 Plastics pipes and fittings Preparation of test piece assemblies
between a polyethylene (PE) pipe and an electrofusion fitting
BDS ISO 11414, Plastics pipes and fittings Preparation of
polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies
by butt fusion
BDS ISO 12176-2:2010 Plastics pipes and fittings Equipment for fusion jointing
polyethylene systems Part 2: Electrofusion
polyethylene systems Part 3: Operators badge
polyethylene systems Part 4: Traceability coding
BDS ISO 13479:2010 Polyolefin pipes for the conveyance of fluids Determination of
Part 5
Building Materials

5-66 Vol. 2
resistance to crack propagation Test method for slow crack
growth on notched pipes (notch test)
BDS ISO 13761:2010 Plastics pipes and fittings Pressure reduction factors for
polyethylene pipeline systems for use at temperatures above 20
C
BDS ISO 13951:2010 Plastics piping systems Test method for the resistance of
polyolefin pipe/pipe or pipe/fitting assemblies to tensile loading
BDS ISO 13953:2010

Polyethylene (PE) pipes and fittings Determination of the
tensile strength and failure mode of test pieces from a butt-fused
joint
BDS ISO 13954:2010 Plastics pipes and fittings Peel decohesion test for
polyethylene (PE) electrofusion assemblies of nominal outside
diameter greater than or equal to 90 mm
BDS ISO 13955:2010 Plastics pipes and fittings Crushing decohesion test for
polyethylene (PE) electrofusion assemblies
BDS ISO 13957:2010 Plastics pipes and fittings Polyethylene (PE) tapping tees
Test method for impact resistance
BDS ISO 14236:2010 Plastics pipes and fittings Mechanical-joint compression
fittings for use with polyethylene pressure pipes in water supply
systems
BDS ISO 18553:2010 Method for the assessment of the degree of pigment or carbon
black dispersion in polyolefin pipes, fittings and compounds
BDS ISO 18553:2010 Method for the assessment of the degree of pigment or carbon
black dispersion in polyolefin pipes, fittings and compounds
Amendment 1:2010
BDS ISO 4427-1:2010 Plastics piping systems Polyethylene (PE) pipes and fittings for
water supply Part 1: General
water supply Part 2: Pipes
water supply Part 3: Fittings
water supply Part 5: Fitness for purpose of the system
water supply Part 1: General Technical corrigendum 1: 2010

pressure pipes Test of leakproofness under internal pressure
BDS ISO 3459:2010 Polyethylene (PE) pressure pipes Joints assembled with
mechanical fittings Internal under pressure test method and
requirement
ASTM A74 - 09 Standard Specification for Cast Iron Soil Pipe and Fittings
ASTM A377 - 03(2008)e1 Standard Index of Specifications for Ductile-Iron Pressure Pipe
ASTM B42 - 02e1 Standard Specification for Seamless Copper Pipe, Standard Sizes
ASTM B43 - 09 Standard Specification for Seamless Red Brass Pipe, Standard
Sizes
ASTM B75 - 02 Standard Specification for Seamless Copper Tube
ASTM B88 - 09 Standard Specification for Seamless Copper Water Tube
ASTM B251 - 02e1 Standard Specification for General Requirements for Wrought
Seamless Copper and Copper-Alloy Tube
ASTM B302 - 07 Standard Specification for Threadless Copper Pipe, Standard
Sizes
ASTM B306 - 09 Standard Specification for Copper Drainage Tube (DWV)
ASTM B429 / B429M -
06
Standard Specification for Aluminum-Alloy Extruded Structural
Pipe and Tube
ASTM B447 - 07 Standard Specification for Welded Copper Tube
ASTM B745 / B745M -
97(2005)
Standard Specification for Corrugated Aluminum Pipe for Sewers
and Drains
ASTM C14 - 07 Standard Specification for Nonreinforced Concrete Sewer, Storm
Drain, and Culvert Pipe
ASTM C76 - 10a Standard Specification for Reinforced Concrete Culvert, Storm
Drain, and Sewer Pipe
ASTM C508 / C508M -
00(2009)e1
Standard Specification for Asbestos-Cement Underdrain Pipe
ASTM C654 - 05a Standard Specification for Porous Concrete Pipe
ASTM C700 - 09 Standard Specification for Vitrified Clay Pipe, Extra Strength,
Standard Strength, and Perforated
Part 5
Building Materials

5-68 Vol. 2
ASTM D1527 - 99(2005) Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS)
Plastic Pipe, Schedules 40 and 80
ASTM D1785 - 06 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe,
Schedules 40, 80, and 120
ASTM D2239 - 03 Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-
PR) Based on Controlled Inside Diameter
ASTM D2241 - 09 Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-
Rated Pipe (SDR Series)
ASTM D2321 - 09 Standard Practice for Underground Installation of Thermoplastic
Pipe for Sewers and Other Gravity-Flow Applications ASTM
D2464 - 06 Standard Specification for Threaded Poly(Vinyl
Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
ASTM D2466 - 06 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe
Fittings, Schedule 40ASTM D2467 - 06 Standard Specification for
Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
ASTM D2609 - 02(2008) Standard Specification for Plastic Insert Fittings for Polyethylene
(PE) Plastic Pipe
ASTM D2661 - 08 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS)
Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

ASTM D2665 - 09
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic
Drain, Waste, and Vent Pipe and Fittings
ASTM D2672 - 96a(2009) Standard Specification for Joints for IPS PVC Pipe Using Solvent
Cement
ASTM D2729 - 03 Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe
and Fittings
ASTM D2737 - 03 Standard Specification for Polyethylene (PE) Plastic Tubing
Sewer Pipe and Fittings
ASTM D2846 / D2846M -
09b
Standard Specification for Chlorinated Poly(Vinyl Chloride)
(CPVC) Plastic Hot- and Cold-Water Distribution Systems
ASTM D2949 -
01a(2008)e1
Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl
Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
ASTM D3034 - 08 Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC)
Sewer Pipe and Fittings

ASTM F405 - 05 Standard Specification for Corrugated Polyethylene (PE) Pipe and
Fittings
ASTM F409 - 02(2008) Standard Specification for Thermoplastic Accessible and
Replaceable Plastic Tube and Tubular Fittings
ASTM F437 - 09 Standard Specification for Threaded Chlorinated Poly(Vinyl
Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
ASTM F438 - 09 Standard Specification for Socket-Type Chlorinated Poly(Vinyl
Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40
ASTM B209 - 07 Standard Specification for Aluminum and Aluminum-Alloy Sheet
and Plate
ASTM F441 / F441M - 09 Standard Specification for Chlorinated Poly(Vinyl Chloride)
(CPVC) Plastic Pipe, Schedules 40 and 80
ASTM F442 / F442M - 09 Standard Specification for Chlorinated Poly(Vinyl Chloride)
(CPVC) Plastic Pipe (SDRPR)
ASTM F628 - 08 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS)
Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular
Core
ASTM F891 - 09 Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC)
Plastic Pipe With a Cellular Core
IS 404 (Part-I)-1993

Specification for Lead Pipes Part I for other than Chemical
Purpose (third Revision);
ISO 160: 1980 Asbestos-Cement Pressure Pipes and Joints;
ISO 392:1986 Asbestos-Cement Pipe Fittings for Building and Sanitary
Purposes;
ISO 881:1980 Asbestos-Cement Pipes, Joints and Fittings for Sewerage and
Drainage;
ISO 2531-1991 Ductile Iron Pipes, Fittings and Accessories for Pressure Pipelines;
ASME/ANSI B16.3-
2006
Malleable Iron Threaded Fittings: Classes 150 and 300;
ASME/ANSI B16.485 Cast Iron Threaded Fittings;
ASME/ANSI B16.9-
2007
Factory Made Wrought Steel Buttwelding Fittings;
ASME/ANSI B16.11-
2009
Forged Steel Fittings, Socket-Welding and Threaded;
Part 5
Building Materials

5-70 Vol. 2
ASME/ABSI B16.12-
2009
Cast-Iron Threaded Drainage Fittings;
ASME/ANSI B16.15-
2006
Cast Copper Alloy Threaded Fittings: Classes 125 and 250;
ASME/ANSI B16.18-
2001
Cast Copper Alloy Solder Joint Pressure Fittings;
ASME/ANSI B16.22-
2001
Wrought Copper and Copper Alloy Solder Joint Pressure Fittings;
ASME/ANSI B16.23-
2002
Cast Copper Alloy Solder Joint Drainage Fittings (DWV);
ASME/ANSI B16.28-
1994
Wrought Steel Butt welding Short radius Elbows and Returns;
ASME/ANSI B16.29-
2007
Wrought Copper and Wrought Copper Alloy Solder Joint Fittings
for solvent Drainage Systems;
ASME/ANSI B16.32-
84
Cast Copper Alloy Solder Joint Fittings for Solvent Drainage
Systems;
AWWA C110-08 Standard for Grey Iron and Ductile Iron Fittings, 76 mm to 1220
mm (3 in. through 48 inches), for Water and Other Liquids.
2.15.3 Joints and Connections Between Pipes and Fittings
Applicable standards for joints and connections between pipes and fittings are listed below:
BDS EN 681-1: 2008 Elastomeric seals Materials requirements for pipe joint seals
used in water and drainage applications Part 1: Vulcanized
rubber
BDS EN 681-2 : 2008 Elastomeric seals Materials requirements for pipe joint seals
used in water and drainage applications Part 2: Thermoplastic
elastomers
ASTM B42 - 02e1 Standard Specification for Seamless Copper Pipe, Standard Sizes
ASTM C425 - 04(2009)

Standard Specification for Compression Joints for Vitrified Clay
Pipe and Fittings
ASTM C443 - 05ae1 Standard Specification for Joints for Concrete Pipe and Manholes,
Using Rubber Gaskets
ASTM C564 - 09a Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe
and Fittings

ASTM D1869 -
95(2005)e1
Standard Specification for Rubber Rings for Asbestos-Cement Pipe
ASTM D2235 - 04 Standard Specification for Solvent Cement for Acrylonitrile-
Butadiene-Styrene (ABS) Plastic Pipe and Fittings
ASTM D2564 -
04(2009)e1
Standard Specification for Solvent Cements for Poly(Vinyl
Chloride) (PVC) Plastic Piping Systems
ASTM D2657 - 07 Standard Practice for Heat Fusion Joining of Polyolefin Pipe and
Fittings
Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
ASTM D2846 / D2846M -
09b
Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC)
Plastic Hot- and Cold-Water Distribution Systems
ASTM D2855 - 96(2010)

Standard Practice for Making Solvent-Cemented Joints with
Poly(Vinyl Chloride) (PVC) Pipe and Fittings
ASTM D3139 - 98(2005) Standard Specification for Joints for Plastic Pressure Pipes Using
Flexible Elastomeric Seals
ASTM D3212 - 07 Standard Specification for Joints for Drain and Sewer Plastic Pipes
Using Flexible Elastomeric Seals
ASTM F402 - 05 Standard Practice for Safe Handling of Solvent Cements, Primers,
and Cleaners Used for Joining Thermoplastic Pipe and Fittings
ASTM F493 - 04

Standard Specification for Solvent Cements for Chlorinated
Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings
ASTM F628 - 08 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS)
Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular
Core
ASTM F656 - 08 Standard Specification for Primers for Use in Solvent Cement
Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings
ASME/ANSI B1.20.1-
1983 (R2006)
Pillar taps used in water supply

2.15.4 Taps and Valves
Taps and valves shall conform to the following standards :
BDS 1507 : 1995 Bib taps used in water supply
Part 5
Building Materials

5-72 Vol. 2
BDS 1508:1995 Stop taps used in water supply.
BDS 1509:1995 Pillar taps used in water supply
BDS 987 : 1981

Sand cast brass screw-down bib taps and stop taps for water
services.
It covers the requirements regarding materials, dimensions,
constructions, workmanship, finish and testing of tapes for water
services.
BDS 1508 : 1995 Stop taps used in water supply.Specifies the requirements,
dimensions construction, materials and test methods of stop taps
used in water supply.
BDS EN 200: 2009 Sanitary tapware Single taps and combination taps for water
supply systems of type 1 and type 2 General technical
specification
BDS EN 246: 2009

Sanitary tapware General specifications for flow rate regulators
BDS EN 248: 2009 Sanitary tapware General specification for electrodeposited
coatings of Ni-Cr
BDS EN 1112: 2009

Sanitary tapware - Shower outlets for sanitary tapware for water
specification
BDS EN 1113: 2009 Sanitary tapware Shower hoses for sanitary tapware for water
specification
BS 1212 3 (Parts) Specification for Float Operated Valves (excluding floats);
BS 1010 Specification for Draw-Off Taps and Stopvalves for Water
Services;
BS 1968 Specification for Floats for Ball Valves (copper);
BS 5433: 1976 Specification for Underground Stop valves for Water Services
(copper);
BS 2456: 1973 Specification for Floats for Ball Valves (plastic) for Cold and Hot
Water
BS 1415 ( 2 parts) Mixing Valves (Manullay Operated);
BS 5163: 1986 Specification for Predominantly Key-Operated Cast Iron Wedge
Gate Valve for Water Works;

BS 3377:1985 Specification for Boilers for Use with Domestic Solid Mineral Fuel
Appliances;
BS 843: 1976 Specification for Thermal Storage Electric Water Heaters;
BS 855:1976 Specification for Welded Steel Boilers for Central Heating and
Indirect Hot Water Supply.
2.16 MISCELLANEOUS MATERIALS
2.16.1 Ferrocement
Details including material requirements are given in Chapter 12 of Part 6.
2.16.2 Plastics
Plastics may be used in buildings or structures as light transmitting materials such as glazing, skylights, lighting
lenses, luminous ceilings, roof panels, signs and similar purposes. Foam plastics are also used in buildings.
Applicants for approval of a plastic material shall furnish all necessary technical data required by the Building
Official. The data shall include chemical composition; applicable physical, mechanical and thermal properties such
as fire resistance, flammability and flame spread; weather resistance; electrical properties; products of
combustion; and coefficient of expansion.
The requirements for light transmitting plastics, including roof panels and foam plastics are given below.
2.16.2.1 Light Transmitting Plastics
An approved light transmitting plastic shall be any thermoplastic, thermosetting or reinforced thermosetting
plastic material which has a self-ignition temperature of 343
o
C or greater when tested in accordance with , Test
Method for Ignition Properties of Plastics; a smoke density rating not greater than 450 when tested in the manner
intended for use in accordance with ASTM E84 - 10, Test Method for Surface Burning Characteristics of Building
Materials; or not greater than 75 when tested in the thickness intended for use in accordance with ASTM D2843 -
10, Test Method for Density of Smoke from the Burning or Decomposition of Plastics; and which conforms to one
of the following combustibility classifications:
Class C1 : Plastic materials which have a burning extent of 25 mm or less when tested at a nominal thickness of
1.5 mm, or in the thickness intended for use, in accordance with ASTM D635 - 06, Test Method for Rate of
Burning and/or Extent and Time of Burning of Self-Supporting Plastics in Horizontal Position; or
Class C2: Plastic materials which have a burning rate of 63 mm/min or less when tested at a nominal thickness of
1.5 mm, or in the thickness intended for use, in accordance with ASTM D635 - 06.
2.16.2.2 Foam Plastics
All foam plastics and foam plastic cores of manufactured assemblies shall have a flame spread rating of not more
than 75 and shall have a smoke developed rating of not more than 450 when tested in the maximum thickness
intended for use in accordance with ASTM E84 - 10.
All foam plastics, unless otherwise indicated in this section, shall be separated from the interior of a building by an
approved thermal barrier of 13 mm gypsum wall board or equivalent thermal barrier material which will limit the
average temperature rise of the unexposed surface to not more than 121
o
C after 15 minutes of fire exposure
complying with the standard time-temperature curve of ASTM E119 - 09c, Test Methods for Fire Tests of Building
Construction and Materials. The thermal barrier shall be installed in such a manner that it will stay in place for a
Part 5
Building Materials

5-74 Vol. 2
minimum of 15 minutes under the same testing conditions. The thermal barrier is not required when the foam
plastic is protected by a 25 mm minimum thickness of masonry or concrete.
2.16.2.3 Applicable Standards
A list of applicable standards for plastics is given below:
BDS 885:1979

Method for Measuring Viscosity Number and K-Value of PVC Resins;
BDS 886:1978

Method for Direct Measuring the Specific Gravity of Plastics;
BDS 887:1978

Method for Measuring Deformation under Heat of Flexible Rigid
PVC Compounds;
BDS 888:1978

Method for Measuring Temperature of Deflection under Load;
BDS 889:1978

Method for Measuring the Vicat Softening Temperature (VST) of
Thermoplastics;
BDS 890:1978

Method for Measuring the Water Absorption at Room Temperature
and Bolling Water Absorption of Plastics;
BDS 891:1978

Method for Measuring the Flexural Modulus of Plastics;
BDS 892:1978

Method for Measuring the Resistance to Tear Propagation of
Flexible Plastics, Film or Sheeting;
ASTM D543 - 06 Standard Practices for Evaluating the Resistance of Plastics to
Chemical Reagents
ASTM D635 - 06 Standard Test Method for Rate of Burning and/or Extent and Time
of Burning of Plastics in a Horizontal Position
ASTM D638 - 08 Standard Test Method for Tensile Properties of Plastics
ASTM D695 - 08 Standard Test Method for Compressive Properties of Rigid Plastics
ASTM D882 - 09 Standard Test Method for Tensile Properties of Thin Plastic Sheeting
ASTM D1003 - 07e1 Standard Test Method for Haze and Luminous Transmittance of
Transparent Plastics
ASTM D1044 - 08 Standard Test Method for Resistance of Transparent Plastics to
Surface Abrasion
ASTM D1204 - 08 Standard Test Method for Linear Dimensional Changes of Nonrigid

Thermoplastic Sheeting or Film at Elevated Temperature
ASTM D1593 - 09 Standard Specification for Nonrigid Vinyl Chloride Plastic Film and
Sheeting
ASTM D2103 - 08 Standard Specification for Polyethylene Film and Sheeting
ASTM D2126 - 09 Standard Test Method for Response of Rigid Cellular Plastics to
Thermal and Humid Aging
ASTM D2842 - 06 Standard Test Method for Water Absorption of Rigid Cellular
Plastics
ASTM D2843 - 10 Standard Test Method for Density of Smoke from the Burning or
Decomposition of Plastics
ASTM D3294 - 09 Standard Specification for PTFE Resin Molded Sheet and Molded
Basic Shapes
ASTM D3678 -
97(2008)e1
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-
Profile Extrusions
ASTM D3679 - 09a Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
ASTM D3841 -
97(2008)e1
Standard Specification for Glass-Fiber-Reinforced Polyester Plastic
Panels
ASTM D4802 - 02 Standard Specification for Poly(Methyl Methacrylate) Acrylic Plastic
Sheet
ASTM E84 - 10 Standard Test Method for Surface Burning Characteristics of
Building Materials
ASTM E119 - 09c Standard Test Methods for Fire Tests of Building Construction and
Materials
2.16.3 Ballies and Wood Poles
Ballies of Sal/Gazari, Sundari and Garjan are used in building construction. These shall be free from rots, knots
and sap, and straight and uniform in size. These should conform to the following standards:
BDS 809:1973 Specification for Wood Poles for Overhead Power and
Telecommunication Lines;
ASTM D25 - 99(2005) Standard Specification for Round Timber Piles
IS 3337:1978 Specification for Ballies for General Purposes (First Revision);
IS 1900:1974 Method of Testing Wood Poles;
IS 6711:1972

Code of Practice for Maintenance of Wood Poles for Overhead
Power and Telecommunications Lines.
Part 5
Building Materials

5-76 Vol. 2

2.16.4 Bamboos
The following standards shall be applicable for bamboos used for structural and nonstructural purposes:
IS 1902:1961

Code of Practice for Preservation of Bamboo and Cane for Non-
structural Purposes;
IS 6874:1973 Method of Tests for Round Bamboos;
IS 8242:1976 Methods of Tests for Split Bamboo;
IS 8295:1976 Specification for Bamboo Chicks, Part I Fine;
IS 9096:1979 Code of Practice for Preservation of Bamboos for Structural
Purposes.
2.16.5 Fillers, Stoppers and Putties
IS 110:1968

Specification for Ready Mixed Paint, Brushing, Grey Filler, for
Enamels, for Use Over Primers (First Revision);
IS 345:1952 Specification for Wood Filler, Transparent, Liquid;
IS 419:1967 Specification for Putty for Use on Window Frames (First Revision);
IS 421:1953 Specification for Jointing Paste, for Bedding Moldings on Coaching
Stock;
IS 423:1961 Specification for Plastic Wood, for Joiners' Filler (revised);
IS 424:1965 Specification for Plastic Asphalt (revised);
IS 3709:1966 Specification for Mastic Cement for Bedding of Metal Windows;
IS 7164:1973 Specification for Stopper.
2.16.6 Wire Ropes and Wire Products
ASTM A116 - 05 ASTM
A121 - 07
Standard Specification for Metallic-Coated Carbon Steel Barbed
Wire
ASTM A368 -
95a(2009)
Standard Specification for Stainless Steel Wire Strand
ASTM A392 - 07 Standard Specification for Zinc-Coated Steel Chain-Link Fence
Fabric

ASTM A475 -
03(2009)e1
Standard Specification for Zinc-Coated Steel Wire Strand
ASTM A492 - 95(2009) Standard Specification for Stainless Steel Rope Wire
ASTM A510 - 08 Standard Specification for General Requirements for Wire Rods
and Coarse Round Wire, Carbon Steel
ASTM A121 - 07 Standard Specification for Metallic-Coated Carbon Steel Barbed
Wire
ASTM A586 -
04a(2009)e1
Standard Specification for Zinc-Coated Parallel and Helical Steel
Wire Structural Strand
ASTM A603 -
98(2009)e1
Standard Specification for Zinc-Coated Steel Structural Wire Rope
ASTM A817 - 07 Standard Specification for Metallic-Coated Steel Wire for Chain-
Link Fence Fabric and Marcelled Tension Wire
ASTM A824 - 01(2007) Standard Specification for Metallic-Coated Steel Marcelled Tension
Wire for Use With Chain Link Fence
ASTM F1183 -
96(2006)
Standard Specification for Aluminum Alloy Chain Link Fence Fabric
IS 2365:1977

Specification for Steel Wire Suspension Ropes for Lifts, Elevators
and Hoists (First Revision).

2.16.7 Waterproofing and Damp-proofing Materials
Waterproofing and damp-proofing materials shall conform to the following standards:
ASTM D41 - 05 Standard Specification for Asphalt Primer Used in Roofing, Damp
proofing, and Waterproofing
ASTM D43 - 00(2006) Standard Specification for Coal Tar Primer Used in Roofing, Damp
ASTM D146 - 04 Standard Test Methods for Sampling and Testing Bitumen-
Saturated Felts and Woven Fabrics for Roofing and Waterproofing
ASTM D173 - 03 Standard Specification for Bitumen-Saturated Cotton Fabrics Used
ASTM D6380 -
03(2009)
Standard Specification for Asphalt Roll Roofing (Organic Felt)
ASTM D226 / D226M -
09
Standard Specification for Asphalt-Saturated Organic Felt Used in
Roofing and Waterproofing
Part 5
Building Materials

5-78 Vol. 2
ASTM D227 - 03 Standard Specification for Coal-Tar-Saturated Organic Felt Used in
ASTM D449 - 03(2008) Standard Specification for Asphalt Used in Damp proofing and
Waterproofing
ASTM D450 - 07 Standard Specification for Coal-Tar Pitch Used in Roofing, Damp
ASTM D1327 - 04 Standard Specification for Bitumen-Saturated Woven Burlap
Fabrics Used in Roofing and Waterproofing
ASTM D1668 -
97a(2006)
Standard Specification for Glass Fabrics (Woven and Treated) for
ASTM D2178 - 04 Standard Specification for Asphalt Glass Felt Used in Roofing and
Waterproofing
ASTM D2626 - 04 Standard Specification for Asphalt-Saturated and Coated Organic
Felt Base Sheet Used in Roofing
ASTM D3468 -
99(2006)e1
Standard Specification for Liquid-Applied Neoprene and
Chlorosulfonated Polyethylene Used in Roofing and Waterproofing
2.16.8 Glazed Tiles and Tile-setting Mortars
Glazed tiles shall conform to the following standards:
BDS 1301:1990 Specification for Glazed Earthenware Wall Tiles;
ASTM C126 - 09

Standard Specification for Ceramic Glazed Structural Clay Facing
ANSI A137.1-2008 Specification for Ceramic Tile;
BS 6431 Part 1
to Part 23
Ceramic Floor and Wall Tiles.
2.16.8.1 Mortars for Ceramic Wall and Floor Tile
a) Portland Cement Mortars: Portland cement mortars for installing ceramic wall and floor tile shall comply
with ANSI A108.1-2009 and be of the compositions indicated in Table 5.2.1.
b) Dry-set Portland Cement Mortars: Premixed prepared Portland cement mortars, which require only the
addition of water and which are used in the installation of ceramic tile, shall comply with ANSI A 118.1-
2009. The shear bond strength for tile set in such mortar shall be as required in accordance with that
standard. Tile set in dry-set Portland cement mortar shall be installed in accordance with ANSI A 108.5-
2009.
c) Electrically Conductive Dry-Set Mortars: Premixed prepared Portland cement mortars, which require only
the addition of water and which comply with ANSI A118.2-2009, shall be used in the installation of

electrically conductive ceramic tile. Tile set in electrically conductive dry-set mortar shall be installed in
accordance with ANSI A 108.7-2009.
d) Latex-modified Portland Cement Mortars: Latex-modified Portland cement thin set mortars in which
Lalex is added to dry-set mortar as a replacement for all or part of the gauging water which are used for
the installation of ceramic tile shall comply with ANSI A 118.4-2009. Tile set in latex-modified Portland
cement mortar shall be installed in accordance with ANSI A 108.5-2009.
e) Epoxy Mortar: Chemical-resistant epoxy for setting and grouting ceramic tile shall comply with ANSI A
118.3-2009. Tile set and grouted with epoxy shall be installed in accordance with ANSI A 108.6-2009.
f) Furan Mortar and Grout: Chemical resistant furan mortar and grout which are used to install ceramic tile
shall comply with ANSI A 118.5-2009. Tile set and grouted with furan shall be installed in accordance with
ANSI A 108.8-2009.
g) Modified Epoxy-Emulsion Mortar and Grout: Modified epoxy-emulsion mortar and grout which are used
to install ceramic tile shall comply with ANSI A 118.8-2009. Tile set and grouted with modified epoxy-
emulsion mortar and grout shall be installed in accordance with ANSI A 108.9-2009.
h) Organic Adhesives: Water-resistant organic adhesives used for the installation of ceramic tile shall comply
with ANSI A 136.1-2009. The shear bond strength after water immersion shall not be less than 0.25
kN/mm2 for Type I adhesive, and not less than 0.13 kN/mm2 for Type II adhesive when tested in
accordance with ANSI A 136.1-2009. Tile set in organic adhesive shall be installed in accordance with
ANSI A 108.4-2009.
i) Portland Cement Grouts: Portland cement grouts used for the installation of ceramic tile shall comply
with ANSI A 118.6-2009. Portland cement grouts for tilework shall be installed in accordance with ANSI A
108.10-2009.
2.16.8.2 Applicable Standards
A list of applicable standards for tiles, mortars and adhesives is given below.
BDS 1301 : 1990

Specification for Glazed Earthenware Wall Tiles;
ASTM C126 - 09 Standard Specification for Ceramic Glazed Structural Clay Facing
ANSI A108.1-2009

Specification for the Installation of Ceramic Tile with Portland
Cement Mortar;
ANSI A108.4-2009

Installation of Ceramic Tile with Organic Adhesives or Water
Cleanable Tile Setting Epoxy Adhesive;
ANSI A108.5-2009

Installation of Ceramic Tile with Dry-Set Portland Cement Mortar or
Latex-Portland Cement Mortar;
ANSI A108.6-2009

Installation of Ceramic Tile with Chemical Resistant, Water
Cleanable Tile Setting and Grouting Epoxy;
ANSI A108.7-2009

Specification for Electrically Conductive Ceramic Tile Installed with
Conductive Dry-Set Portland Cement Mortar;
Part 5
Building Materials

5-80 Vol. 2
ANSI A108.8-2009

Installation of Ceramic Tile with Chemical Resistant Furan Mortar
and Grout;
ANSI A108.9-2009 Installation of Ceramic Tile with Modified Epoxy Emulsion
Mortar/Grout;
ANSI A108.10-2009 Installation of Grout in Tilework;
ANSI A118.1-2009 Specification for Dry-Set Portland Cement Mortar;
ANSI A118.2-2009 Specifications for Conductive Dry-set Portland Cement Mortar;
ANSI A118.3-2009

Specifications for Chemical Resistant Water Cleanable Tile Setting
and Grouting Epoxy and Water Cleanable Tile Setting Epoxy
Adhesive;
ANSI A118.4-2009 Specifications Furan Latex - Portland Cement Mortar;
ANSI A118.5-2009 Specifications for Chemical Resistant Furan;
ANSI A118.6-2009 Specifications for Ceramic Tile Grouts;
ANSI A118.8-2009 Specifications for Modified Epoxy Emulsion Mortar/Grout;
ANSI A136.1-2009 Organic Adhesives for Installation of Ceramic Tile;
ANSI A137.1-2008 Specifications for Ceramic Tile;
BS 6431 Floor and Wall Tiles;
BS 6431 Part 1
1983
Specification for Classification and Making, Including Definitions
and Characteristics;
BS 6431 Part 2
1984
Specification for Struded Ceramic Tiles with Low Water Absorption
(E< 3%) Group A1;
BS 6431 Part 3

Extruded Ceramic Tiles with a Water Absorption of 3% < 6%. Group
A 11a;
BS 6431 Part 3
Section 3.1 1986
Specification for General Products;
BS 6431 Part 3
Section 3.2 1986

Specification for Products Terre Cuite, Cotto, Baldosion Catalan;
BS 6431 Part 4

Extruded Ceramic Tiles with a Water Absorption of 6% <E< 10%.
Group A11b;
BS 6431 Part 4 Specification for General Products;

1986
BS 6431 Part 4
Section 4.2
1986
Specification for Specific Products (Terre Cuite, Cotto, Baldosion
Catalan);
BS 6431 Part 5
1986
Specification for Extruded Ceramic Tiles with a Water Absorption of
E>10%, Group A111;
BS 6431 Part 6
1984
Specification for Dust-prestressed Ceramic Tiles with a Low-Water
Absorption (E<3%)Group B1;
BS 6431 Part 7
1986
Specification for Dust-prestressed Ceramic Tiles with a Water
Absorption of 3% <E 6%. Group B11a;
BS 6431 Part 8
1986
Specification for Dust-prestressed Ceramic Tiles with Water
Absorption of 6% < E 10%. Group B11b;
BS 6431 Part 9
1984
Specification for Dust-Prestressed Ceramic Tiles with a Water
Absorption of E >10%. Group B111;
BS 6431 Part 10
1984
Method for Determination of Dimensions and Surface Quality;
BS 6431 Part 11
1983
Method for Determination of Water Absorption;
BS 6431 Part 12
1983
Method for Determination of Modulus of;
BS 6431 Part 13
1986
Method for Determination of Scratch Hardness of Surface
According to Mhos;
BS 6431 Part 14
1983
Method for Determination of Resistance to Abrasion of Unglazed
Tiles;
BS 6431 Part 15
1983
Method for Determination of Linear Thermal Expansion;
BS 6431 Part 16
1983
Method for Determination of Resistance to Thermal Shock;
BS 6431 Part 17
1983
Method for Determination of Crazing Resistance-Glazed Tiles;
BS 6431 Part 18
1983
Method for Determination of Chemical Resistance-Unglazed Tiles;
BS 6431 Part 19
1984
Method for Determination of Chemical Resistance-Unglazed Tiles;

Part 5
Building Materials

5-82 Vol. 2
BS 6431 Part 20
1984
Method for Determination of Resistance to Surface Abrasion-
Glazed Tiles;
BS 6431 Part 23
1986
Specification for Sampling and Basis for Acceptance;
2.16.9 Refractories
Refractories shall conform to the following standards:
BDS 1493:1994 Glossary of terms used in refractory
BDS 1494:1994 Dimension of refractory bricks
BDS 1495:1994 High aluminium refractory bricks
ISO 528:1983

Refractory Products-Determination of Pyrometric Cone Equivalent
(refractoriness);
ISO 1109:1975

Refractory Products-Classification of Dense Shaped Refractory
Products;
ISO 1146:1988

Pyrometric Reference Cones for Laboratory Use-Specification;
ISO 1893:1989

Refractory Products-Determination of Refractoriness-Under-Load
(differential with rising temperature);
ISO 1927:1984

Prepared Unshaped Refractory Materials (Dense and Insulating)
Classification;
ISO 2245:1990 Shaped Insulating Refractory Products-Classification;
ISO 2477:1987 Shaped Insulating Refractory Products-Determination of
Permanent Change in Dimensions on Heating;
ISO 2478:1987

Dense Shaped Refractory Products-Determination of Permanent
Change in Dimensions on Heating;
ISO 3187:1989

Refractory Products-Determination of Creep in Compression;
ISO 5013:1985

Refractory Products-Determination of Modulus of Rupture at
Elevated Temperatures;
ISO 5014:1986

Refractory Products-Determination of Modulus of Rupture at
Ambient Temperature;
ISO 5016:1986

Shaped Insulating Refractory Products-Determination of Bulk
Density and True Porosity;
ISO 5017:1988 Dense Shaped Refractory Products-Determination of Bulk Density,

Apparent Porosity and True Porosity;
ISO 5018:1983 Refractory Materials-Determination of True Density;
ISO 5019-1:1984 Refractory Bricks-Dimensions-Part I: Rectangular Bricks;
ISO 5019-2:1984 Refractory Bricks-Dimensions-Part 2: Arch Bricks;
ISO 5019-3:1984

Refractory Bricks-Dimensions-Part 3: Rectangular Checker Bricks
for Regenerative Furnace;
ISO 5419-4:1988

Refractory Bricks-Dimensions-Part 4: Dome Bricks for Electric arc
Furnace Roofs;
ISO 5015-6:1984

Refractory Bricks-Dimensions-Part 6: Basic Bricks for Oxygen Steel
Making Converters;
ISO 5022:1979 Shaped Refractory Products-Sampling and Acceptance Testing;
ISO 5417-1986 Refractory Bricks for Use in Rotary Kilns-Dimensions;
ISO 8656:1988

Refractory Products-Sampling of Raw Materials and Unshaped
Products;
Part 1; Sampling Scheme;
ISO 8840:1987 Refractory Materials-Determination of Bulk Density of Granular
Materials (Grain Density);
ISO 8890:1988

Dense Shaped Refractory Products-Determination of Resistance to
Sulfuric Acid;
ISO 8894-1:1987 Refractory Materials-Determination of Thermal Conductivity-
Part 1: Hot-Wire Method (Cross-Array);
ISO 8894-2:1990 Refractory Materials-Determination of Thermal Conductivity-
Part 2: Hot-Wire Method (Parallel);
ISO 8895:1986 Shaped Insulating Refractory Products-Determination of Cold
Crushing Strength;
ISO 9205:1988

Refractory Bricks for Use in Rotary Kilns-Hot-face Identification
Marking;
ISO 10080:1990

Refractory Products-Classification of Dense, Shaped Acid-Resisting
Products;
ISO 10081:1991

Basic Refractory Products-Classification-Part I: Products Containing
Less Than 7% Residual Carbon.
Part 5
Building Materials

5-84 Vol. 2
2.16.10 Thermal Insulating Materials
Thermal insulation may be in the following physical forms:
Loose fill dry granules or nodules poured or below in place;
Flexible or semi rigid blankets and bolts of wool like material;
Rigid boards and blocks;
Membrane reflective insulation;
Spray applied mineral fibre or insulating concrete;
Poured in plain-insulating concrete;
Foamed in place-polyurethane;
Gypsum plaster.
Thermal insulating materials shall conform to the standards listed below.
ASTM C167 - 09 Standard Test Methods for Thickness and Density of Blanket or
Batt Thermal Insulations
ASTM C177 - 04 Standard Test Method for Steady-State Heat Flux Measurements
and Thermal Transmission Properties by Means of the Guarded-
Hot-Plate Apparatus
ASTM C195 - 07 Standard Specification for Mineral Fiber Thermal Insulating
Cement
ASTM C196 - 00(2005) Standard Specification for Expanded or Exfoliated Vermiculite
Thermal Insulating Cement
ASTM C208 - 08a Standard Specification for Cellulosic Fiber Insulating Board
ASTM C209 - 07ae1 Standard Test Methods for Cellulosic Fiber Insulating Board
ASTM C1363 - 05 Standard Test Method for Thermal Performance of Building
Materials and Envelope Assemblies by Means of a Hot Box
Apparatus
ASTM C240 - 08e1 Standard Test Methods of Testing Cellular Glass Insulation Block
ASTM C335 - 05ae1 Standard Test Method for Steady-State Heat Transfer Properties of
Pipe Insulation
ASTM C411 - 05 Standard Test Method for Hot-Surface Performance of High-
Temperature Thermal Insulation
ASTM C449 - 07 Standard Specification for Mineral Fiber Hydraulic-Setting Thermal
Insulating and Finishing Cement
ASTM C516 - 08 Standard Specification for Vermiculite Loose Fill Thermal Insulation

ASTM C518 - 04

Standard Test Method for Steady-State Thermal Transmission
Properties by Means of the Heat Flow Meter Apparatus
ASTM C520 - 04 Standard Test Methods for Density of Granular Loose Fill
Insulations
ASTM C533 - 09 Standard Specification for Calcium Silicate Block and Pipe Thermal
Insulation
ASTM C534 / C534M -
08
Standard Specification for Preformed Flexible Elastomeric Cellular
Thermal Insulation in Sheet and Tubular Form
ASTM C547 - 07e1 Standard Specification for Mineral Fiber Pipe Insulation
ASTM C549 - 06 Standard Specification for Perlite Loose Fill Insulation
ASTM C552 - 07 Standard Specification for Cellular Glass Thermal Insulation
ASTM C553 - 08 Standard Specification for Mineral Fiber Blanket Thermal
Insulation for Commercial and Industrial Applications
ASTM C578 - 09e1 Standard Specification for Rigid, Cellular Polystyrene Thermal
Insulation
ASTM C591 - 09 Standard Specification for Unfaced Preformed Rigid Cellular
Polyisocyanurate Thermal Insulation
ASTM C592 - 08a Standard Specification for Mineral Fiber Blanket Insulation and
Blanket-Type Pipe Insulation (Metal-Mesh Covered) (Industrial
Type)
ASTM C610 - 09e1 Standard Specification for Molded Expanded Perlite Block and Pipe
Thermal Insulation
ASTM C612 - 09 Standard Specification for Mineral Fiber Block and Board Thermal
Insulation
ASTM C665 - 06 Standard Specification for Mineral-Fiber Blanket Thermal
Insulation for Light Frame Construction and Manufactured Housing
ASTM C726 - 05e1 Standard Specification for Mineral Fiber Roof Insulation Board
ASTM C728 - 05(2010) Standard Specification for Perlite Thermal Insulation Board
ASTM C739 - 08 Standard Specification for Cellulosic Fiber Loose-Fill Thermal
Insulation
ASTM C764 - 07 Standard Specification for Mineral Fiber Loose-Fill Thermal
Insulation
ASTM C916 - 85(2007) Standard Specification for Adhesives for Duct Thermal Insulation
Part 5
Building Materials

5-86 Vol. 2
ASTM C991 - 08e1 Standard Specification for Flexible Fibrous Glass Insulation for
Metal Buildings
ASTM C1014 - 08 Standard Specification for Spray-Applied Mineral Fiber Thermal
and Sound Absorbing Insulation
ASTM C1029 - 09 Standard Specification for Spray-Applied Rigid Cellular
Polyurethane Thermal Insulation
ASTM C1071 - 05e1 Standard Specification for Fibrous Glass Duct Lining Insulation
(Thermal and Sound Absorbing Material)

2.16.11 Screw Threads and Rivets
IS 554:1975

Dimensions for Pipe Threads where Pressure Tight Joints are
Required on the Threads (Second Revision);
IS 1929:1982

Specification for Hot Forged Steel Rivets for Hot Closing (12 to 36
mm diameter) (First Revision);
IS 2155:1982

Specification for Cold-Forged Solid Steel Rivets for Hot Closing (6
to 16 mm diameter) (First Revision);
IS 2643:1975 Dimensions for Pipe Threads for Fastening Purposes;
Part I - Basic Profile and Dimensions (First Revision);
Part II - Tolerances (First Revision);
Part III - Limits of Sizes;
IS 2907:1964 Specification for Non-ferrous Rivets (1.6 mm to 10 mm)
IS 2998:1981

Specification for Cold Forged Steel Rivets for Cold Closing (1 to 16
mm diameter) (First Revision);
IS 10102:1982 Technical supply conditions for Rivets.
2.16.12 Sealants
Sealants shall conform to the following standards:
ASTM C509 - 06 Standard Specification for Elastomeric Cellular Preformed Gasket
and Sealing Material
ASTM C542 - 05 Standard Specification for Lock-Strip Gaskets

ASTM C564 - 09a

Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe
and Fittings
ASTM C716 - 06 Standard Specification for Installing Lock-Strip Gaskets and Infill
Glazing Materials
ASTM C719 - 93(2005) Standard Test Method for Adhesion and Cohesion of Elastomeric
Joint Sealants Under Cyclic Movement (Hockman Cycle)
ASTM C1193 - 09 Standard Guide for Use of Joint Sealants
ASTM C794 - 06 Standard Test Method for Adhesion-in-Peel of Elastomeric Joint
Sealants
ASTM C834 - 10 Standard Specification for Latex Sealants
ASTM C864 - 05 Standard Specification for Dense Elastomeric Compression Seal
Gaskets, Setting Blocks, and Spacers
ASTM C919 - 08 Standard Practice for Use of Sealants in Acoustical Applications
ASTM C920 - 08 Standard Specification for Elastomeric Joint Sealants
ASTM C1193 - 09 Standard Guide for Use of Joint Sealants
ASTM D2628 - 91(2005) Standard Specification for Preformed Polychloroprene Elastomeric
Joint Seals for Concrete Pavements
ASTM D6690 - 07 Standard Specification for Joint and Crack Sealants, Hot Applied,
for Concrete and Asphalt Pavements
ASTM D3406 - 95(2006) Standard Specification for Joint Sealant, Hot-Applied, Elastomeric-
Type, for Portland Cement Concrete Pavements
ASTM D3667 - 05 Standard Specification for Rubber Seals Used in Flat-Plate Solar
Collectors
ASTM D3771 - 03(2007) Standard Specification for Rubber Seals Used in Concentrating
Solar Collectors
ASTM D3832 - 79(2006)

Standard Specification for Rubber Seals Contacting Liquids in Solar
Energy Systems
ISO 3934:1978

Rubber Building Gaskets-Materials in Preformed Solid
Vulcanizates Used for Sealing Glazing and Panels-Specification;
ISO 4633:1983

Rubber Seals-Joint Rings for Water Supply, Drainage and
Sewerage Pipelines-Specifications for Materials;
ISO 4635:1982 Rubber, Vulcanized-Preformed Compression Seals for Use
Part 5
Building Materials

5-88 Vol. 2
Between Concrete Motorway Paving Sections-Specifications for
Material;
ISO 5892:1981

Rubber Building Gaskets-Materials for Preformed Solid Vulcanized
Structural Gaskets-Specification;
ISO 6447:1991

Rubber Seals-Joint Rings Used for Gas Supply Pipes and Fittings-
Specification for Material;
ISO 9331:1991

Rubber Seals Joint Rings for Hot Water Supply Pipelines up to
110oC Specifications for the Material.
2.16.13 Joints and Jointing Products
Joints and jointing products shall conform to the following standards:
ISO 2444 : 1988 Joints in Buildings-Vocabulary;
ISO 3867:1982

Agglomerated Cork-Material of Expansion Joints for Construction
and Building Test-Methods;
ISO 3869:1981 Agglomerated Cork-Filler Material of Expansion Joints for
Construction and Buildings -Characteristics, Sampling and Packing;
ISO 3934:1978 Rubber Building Gaskets-Materials in Preformed Solid
Vulcanizates Used for Sealing Glazing and Panels-Specification;
ISO 4633:1983 Rubber Seals-Joint Rings for Water Supply, Drainage and
Sewerage Pipelines-Specification for Materials;
ISO 4635:1982

Rubber, Vulcanized-Preformed Compression Seals for Use
Between Concrete Motorway Paving Sections-Specification for
Material;
ISO 5892:1981

Rubber Building Gaskets-Materials for Preformed Solid Vulcanized
Structural Gaskets-Specification;
ISO 6447:1983

Rubber Seals-Joint Rings Used for Gas Supply Pipes and Fittings-
Specification for Material;
ISO 6589:1983

Joints in Building-Laboratory Method of Test for Air Permeability
of Joints;
ISO 7389:1987 Building Construction-Jointing Products-Determination of Elastic
Recovery;
ISO 7390:1987

Building Construction-Jointing Products-Determination of
Resistance to Flow;
ISO 7727:1984

Joints in Building-Principles for Jointing of Building Components-
Accommodation of Dimensional Deviations During Construction;

ISO 8339:1984

Building Construction-Jointing Products-Sealants-Determination of
Tensile Properties;
ISO 8340:1984 Building Construction-Jointing Products-Sealants-Determination of
Tensile Properties at Maintained Extension;
ISO 8394:1988

Building Construction-Jointing Products-Determination of
Extrudability of One-Component Sealants;
ISO 9046:1987

Building Construction-Sealants-Determination of Adhesion/
Cohesion Properties at Constant Temperature;
ISO 9047:1989

Building Construction-Sealants-Determination of Adhesion/
Cohesion Properties at Variable Temperatures;
ISO 9631:1991 Rubber Seals-Joint Rings for Hot Water Supply Pipelines up to
110oC Specifications for the Material;
ISO 10563:1991 Building Construction-Sealants for Joints-Determination of Change
in Mass and Volume;
ISO 10590:1991

Building Construction-Sealants-Determination of
Adhesion/Cohesion Properties at Maintained Extension after
Immersion in Water;
ISO 10591 : 1991

Building Construction-Sealants-Determination of
Adhesion/Cohesion Properties after Immersion in Water.
2.16.14 Glass and Glazing
The applicable standards for glass and glazing are listed below :
ASTM C1036 - 06 Standard Specification for Flat Glass
ASTM C1048 - 04 Standard Specification for Heat-Treated Flat GlassKind HS,
Kind FT Coated and Uncoated Glass
ANSI Z 97.1-2009 Safety Performance Specifications and Methods of Tests for
Transport Safety Glazing Materials Used in Building;
CPSC 16 CFR

Safety Standard for Architectural Glazing Materials.
Part 1201A

2.17 CGI SHEET ROOFING AND WALLING
Galvanized corrugated steel sheets conforming to BDS 868, Galvanized Corrugated Sheet Roof and Wall
Coverings, may be used over structural framing for construction of roofs and walls. Requirements for various
roofing materials including CGI sheet have been specified in Sec 2.13 above.
Part 5
Building Materials

5-90 Vol. 2

BNBC Part 05 - Building Materials

Uploaded by

Copyright:

Available Formats

BNBC Part 05 - Building Materials

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BNBC Part 05 - Building Materials

Uploaded by

Copyright:

Available Formats

5-i Vol.

You might also like