User+Manual XDL-L7N+series Eng V1.5

Safety Precautions
Safety Precautions

Introduction
Hello. Thank you for choosing the LSIS XDL-N Series AC Servo.
This user manual describes how to use this product safely and efficiently.
Failure to comply with the guidelines outlined in this manual may cause personal injury or
damage to the product. Be sure to read this manual carefully before using this product and
follow all guidelines contained therein.
The contents of this manual are subject to change without notice.
The reproduction of part or all of the contents of this manual in any form, by any means or for
any purpose is strictly prohibited without the explicit written consent of LSIS.
LSIS retains all patents, trademarks, copyrights and other intellectual property rights to the
material in this manual. The information contained in this manual is only intended for use with
LSIS products.
EtherCAT is registered trademark and patented technology, licensed by Beckhoff Automation
Gmbh, German
Safety Precautions

Safety Precautions
Safety precautions are categorized as either Warnings or Cautions, depending on the
severity of the precaution.
Precautions Definition
Warnings Failure to comply with these guidelines may cause serious injury or death.
Caution
Failure to comply with these guidelines may cause personal injury or property
damage.
Precautions listed as Cautions may also result in serious injury.
Electric Safety Precautions
Warning
Before wiring or inspecting the device, turn off the power, wait 15 minutes, ensure that the
charge lamp is off, and then check the voltage.
Ground both the servo drive and the servo motor.
Only specially trained technicians may perform wiring on this product.
Install both the servo drive and servo motor before performing any wiring.
Do not operate the device with wet hands.
Do not open the servo drive cover during operation.
Do not operate the device with the servo drive cover removed.
Even if the power is off, do not remove the servo drive cover.
Fire Safety Precautions
Caution
Install the servo drive, the servo motor, and the regenerative resistor on non-combustible
materials.
Disconnect the input power if the servo drive malfunctions.

Safety Precautions

Installation Precautions
Store and operate this product under the following environmental conditions.
Environment
Conditions
TheServoDrive TheServoMotor
Operating temp. 0 ~ 50 0 ~ 40
Storage temp. -20 ~ 65 -20 ~ 60
Operating humidity
Below 90% RH (no condensation)
Below 80% RH
Storage humidity Below 90% RH
Altitude 1000m or less
Spacing
When installing 1 unit:
More than 40 mm at the top and
bottom of the control panel
More than 10 mm on the left and
right sides of the control panel
When installing 2 or more units:
More than 100 mm at the top of
the control panel
More than 40 mm at the bottom of
the control panel
More than 30 mm on the left and
right sides of the control panel
More than 2 mm between units
Refer to Section 2.2.2, Wiring the
Control Panel.

Other variables
Ensure the installation location is free from dust, iron, corrosive gas, and
combustible gas.
Ensure the installation location is free from vibrations or the potential for
hard impacts.

Caution
Install the product with the correct orientation.
Do not drop the product or expose it to hard impact.
Install this product in a location that is free from water, corrosive gas, combustible gas, or
flammable materials.
Install this product in a location capable of supporting the weight of this product.
Do not stand on the product or place heavy objects on top of it.
Always maintain the specified spacing when installing the servo drive.
Ensure that there are no conductive or flammable debris inside the servo drive or the servo
motor.
Firmly attach the servo motor to the machine.
Install the servo motor with a correctly oriented decelerator.
Do not touch the rotating unit of the servo motor during operation.
Do not apply excessive force when connecting the couplings to the servo motor shaft.
Do not place loads on the servo motor shaft that exceed the specified amount.

Safety Precautions

Wiring Precautions
Caution
Always use an AC 200-230 V power input for the servo drive.
Always connect the servo drive to a ground terminal.
Do not connect commercial power directly to the servo motor.
Do not connect commercial power directly to the U, V, W output terminals of the servo drive.
Connect the U, V, W output terminals of the servo drive directly to the U, V, W input terminals of
the servo motor, but do not install magnetic contactors between the wires.
Always use pressurized terminals with insulation tubes when connecting the servo drive power
terminal.
Always separate the U, V, and W cables for the servo motor power and encoder cable during
wiring.
Always use the robot cable if the motor moves.
Before performing power line wiring, turn off the input power to the servo drive, and then wait
until the CHARGE lamp turns off.
Startup Precautions
Caution
Check the input voltage (AC 200-230 V) and power unit wiring before supplying power to the
device.
The servo must be off before you turn on the power.
Handling and Operating Precautions
Caution
Check and adjust each parameter before operation.
Do not touch the rotating unit of the motor during operation.
Do not touch the heat sink during operation.
Usage Precautions
Caution
Install an emergency cut-off switch which immediately stops operation in an emergency.
Reset the alarm when the servo is off. The system immediately restarts if the alarm is reset
while the servo is ON.
Use a noise filter or DC reactor to minimize electromagnetic interference. This prevents nearby
electrical devices from malfunctioning due to interference.
Only use approved servo drive and servo motor combinations.
The electric brake on the servo motor stops operation. Do not use it for ordinary braking.
The electric brake may malfunction if the brake degrades or if the mechanical structure is
improper (for example, if the ball screw and servo motor are combined via the timing belt).
Install an emergency stop device to ensure mechanical safety.

Safety Precautions

Malfunction Precautions
Caution
Install a servo motor with an electric brake or separate the brake system for use during
emergencies or device malfunctions.
If an alarm occurs, solve the underlying cause of the problem. After solving the problem and
ensuring safe operation, deactivate the alarm and resume operation.
Do not approach the machine until the problem is solved.
Repair/Inspection Precautions
Caution
Before wiring or inspecting the device, turn off the power, wait 15 minutes, ensure that the
CHARGE lamp is off, and then check the voltage. Enough voltage may remain in the condenser
after the power is off to cause an electric shock.
Only authorized personnel may repair and inspect the device or replace its parts.
Do not modify this device in any way.
General Precautions
Caution
This user manual is subject to change due to product modification or changes in standards. If
such changes occur, we issue a new user manual with a new product number.
Product Application
Caution
This product is not designed or manufactured for machines or systems intended to sustain
human life.
This product is manufactured under strict quality control conditions. Nevertheless, install safety
devices if installing the device in a facility where product malfunctions may result in a major
accident or a significant loss.
EEPROM Lifespan
Caution
The EEPROM is rewritable up to 1 million times for the purpose of recording parameter settings
and other information. The servo drive may malfunction if the total number of the following tasks
exceeds 1 million, depending on the lifespan of the EEPROM.
EEPROM recording as a result of parameter changes
EEPROM recording as a result of an alarm

Safety Precautions

Responding to international regulations
L7 Series responds to international regulations with standard models.
Model Low Voltage Directive EMC Directive
L7NA001B
L7NA002B
L7NA004B
L7NA008B
L7NA010B
L7NA020B
L7NA035B
L7NA050B
EN61800-5-1 EN61800-3
1 : For more information, please feel free to ask LS Mecapion.
2 : Please follow the regulations of destination when exporting.

Table of Contents

Table of Contents
1. Product Configuration .................................................................................................................... 1-1
1.1 Product Verification ............................................................................................................................................. 1-1
1.2 Parts ................................................................................................................................................................... 1-3
1.2.1 Servo Motor Parts ................................................................................................................................... 1-3
1.2.2 Servo Drive Parts .................................................................................................................................... 1-4
1.3 Connector Diagram ............................................................................................................................................ 1-8
2. Installation ........................................................................................................................................ 2-1
2.1 The Servo Motor ................................................................................................................................................. 2-1
2.1.1 Operating Environment ........................................................................................................................... 2-1
2.1.2 Preventing Impact ................................................................................................................................... 2-1
2.1.3 Motor Connection ................................................................................................................................... 2-1
2.1.4 The Load Device Connection ................................................................................................................. 2-2
2.1.5 Cable Installation .................................................................................................................................... 2-2
2.2 The Servo Drive .................................................................................................................................................. 2-3
2.2.1 Operating Environment ........................................................................................................................... 2-3
2.2.2 Wiring the Control Panel ......................................................................................................................... 2-4
2.2.3 Power Supply Wiring .............................................................................................................................. 2-5
3. Wiring................................................................................................................................................ 3-1
3.1 Internal Diagram ................................................................................................................................................. 3-1
3.1.1 L7N Drive Block Diagram [L7NA001B - 7NA004B] .............................................................................. 3-1
3.1.2 L7N Drive Block Diagram [L7NA008B - 7NA035B] .............................................................................. 3-2
3.1.3 L7N Drive Block Diagram [L7NA050B] ................................................................................................... 3-3
3.2 Power Supply Wiring .......................................................................................................................................... 3-4
3.2.1 L7N Drive Wiring Diagram [L7NA001B - 7NA035B] ............................................................................ 3-4
3.2.2 L7 Drive Wiring Diagram [L7N050B] ...................................................................................................... 3-5
3.2.3 Power Circuit Electrical Components ..................................................................................................... 3-6
3.3 Timing Diagram ................................................................................................................................................ 3-10
3.3.1 Timing Diagram During Power Input .................................................................................................... 3-10
3.3.2 Timing Diagram During an Alarm Trigger ............................................................................................. 3-11
3.4 Wiring the Control Signals ................................................................................................................................ 3-12
3.4.1 The Contact Input Signal ...................................................................................................................... 3-12
3.4.2 The Contact Output Signal ................................................................................................................... 3-12
3.5 Connecting Serial Encoder Signals (CN2) ....................................................................................................... 3-13
3.5.1 APCS-ECS Cable .......................................................................................................................... 3-13
3.5.2 APCS-EDS Cable .......................................................................................................................... 3-13
3.5.3 APCS-EES Cable ........................................................................................................................... 3-14
3.6 Connecting Multi-turn Encoder Signals (CN2) ................................................................................................. 3-15
3.6.1 APCS-ECS1 Cable ........................................................................................................................ 3-15
3.6.2 APCS-EDS1 Cable ........................................................................................................................ 3-15
3.6.3 APCS-EES1 Cable ......................................................................................................................... 3-16
3.7 Connecting the Input/Output Signals ............................................................................................................... 3-17
3.7.1 The Names and Functions of the Input Signals (CN1) ......................................................................... 3-17
Table of Contents

3.7.2 The Names and Functions of the Output Signals (CN1) ...................................................................... 3-17
3.7.3 Layout of the Input/Output Signal Connectors ..................................................................................... 3-18
3.7.4 The Names and Functions of Safety Function Signals (CN6) .............................................................. 3-18
3.7.5 The Connector Layout of Safety Function Signals (CN6) .................................................................... 3-18
3.7.6 Operation Method of Safety Function Signals (CN6) ........................................................................... 3-20
3.8 EtherCAT Connection Example ........................................................................................................................ 3-21
3.8.1 Example Connection ............................................................................................................................. 3-21
3.8.2 EtherCAT Connectors and the Pin Map ............................................................................................... 3-22
4. How to use the Loader ................................................................................................................... 4-1
4.1 Name and Function of each parts ...................................................................................................................... 4-1
4.2 Status Summary Display .................................................................................................................................... 4-1
4.3 Display FND Output Object ................................................................................................................................ 4-3
5. EtherCAT Communication ............................................................................................................. 5-1
5.1 The Structure of CANopen over EtherCAT ......................................................................................................... 5-1
5.2 The EtherCAT State Machine ............................................................................................................................. 5-2
5.3 LED State ............................................................................................................................................................ 5-3
5.4 Data Type ........................................................................................................................................................... 5-4
5.5 PDO Mapping ..................................................................................................................................................... 5-5
5.6 Synchronization Using the DC (Distributed Clock) ............................................................................................. 5-8
5.7 Emergency Messages ....................................................................................................................................... 5-11
6. CiA402 Drive Profile ....................................................................................................................... 6-1
6.1 The State Machine .............................................................................................................................................. 6-1
6.2 Operation Modes ................................................................................................................................................ 6-4
6.3 Position Control Modes ...................................................................................................................................... 6-5
6.3.1 Profile Position Mode .............................................................................................................................. 6-5
6.3.2 Interpolated Position Mode ..................................................................................................................... 6-9
6.3.3 Cyclic Synchronous Position Mode ...................................................................................................... 6-11
6.4 Homing ............................................................................................................................................................. 6-13
6.5 Velocity Control Mode ....................................................................................................................................... 6-17
6.5.1 Profile Velocity Mode ............................................................................................................................ 6-17
6.5.2 Cyclic Synchronous Velocity Mode ....................................................................................................... 6-19
6.6 Torque Control Modes ...................................................................................................................................... 6-21
6.6.1 Profile Torque Mode .............................................................................................................................. 6-21
6.6.2 Cyclic Synchronous Torque Mode ........................................................................................................ 6-23
6.7 The Torque Limit Function ................................................................................................................................ 6-25
6.8 Digital Input/Output ........................................................................................................................................... 6-26
6.9 Touch Probe Function ....................................................................................................................................... 6-27
7. L7 Drive Setup ................................................................................................................................. 7-1
7.1 Setting System Parameters ................................................................................................................................ 7-1
7.2 Configuring Control Parameters ......................................................................................................................... 7-4
7.2.1 The Inertia Ratio Setting [0x2100] .......................................................................................................... 7-4
7.2.2 The Position Control Gain....................................................................................................................... 7-5
Table of Contents

7.2.3 The Speed Control Gain ......................................................................................................................... 7-6
7.2.4 The Torque Command Filter Time Constant Time [0x210C] .................................................................. 7-7
7.2.5 Gain 1 Gain 2 Transfer Mode [0x210D] ............................................................................................. 7-7
7.2.6 Gain 1 Gain 2 Transfer Time [0x210E] .............................................................................................. 7-7
7.2.7 P/PI Transfer Mode [0x210D] ................................................................................................................. 7-7
7.2.8 Resonance Avoidance Operations [0x210F], [0x2110], [0x2111] ........................................................... 7-8
7.3 Setting the Input/Output Contact Point Parameters ........................................................................................... 7-9
7.4 Setting Speed Operation Parameters ............................................................................................................... 7-11
7.4.1 Acceleration/Deceleration Time ............................................................................................................ 7-11
7.4.2 The S-Curve Operation [0x2304].......................................................................................................... 7-11
7.4.3 The Manual JOG Operation Speed [0x2305] ....................................................................................... 7-11
7.5 Setting Position Operation Parameters ............................................................................................................. 7-11
7.5.1 Backlash Compensation [0x2403] ........................................................................................................ 7-11
7.6 Setting Parameters for L7N Built-in Functions ................................................................................................. 7-12
7.6.1 Checking/Deleting the Alarm History [0x2700] ..................................................................................... 7-12
7.6.2 Auto Gain Tuning [0x2701] ................................................................................................................... 7-12
7.6.3 Absolute Encoder Reset [0x2702] ........................................................................................................ 7-12
8. Object Dictionary ............................................................................................................................. 8-1
8.1 The Object Dictionary List .................................................................................................................................. 8-1
8.2 General Objects .................................................................................................................................................. 8-4
0x1000, Device Type ........................................................................................................................................... 8-4
0x1001, Error Register ........................................................................................................................................ 8-4
0x1008, Manufacturer Device Name ................................................................................................................... 8-5
0x1009, Hardware Version .................................................................................................................................. 8-5
0x100A, Software Version ................................................................................................................................... 8-5
0x1010, Store Parameters ................................................................................................................................... 8-6
0x1011, Restore Default Parameters .................................................................................................................. 8-8
0x1018, Identity Object ...................................................................................................................................... 8-10
8.3 PDO Mapping Objects ....................................................................................................................................... 8-11
0x1600 to 0x1603, Receive PDO Mapping ....................................................................................................... 8-11
0x1A00 to 0x1A03, Transmit PDO Mapping ..................................................................................................... 8-14
8.4 Sync Manager Communication Objects ........................................................................................................... 8-18
0x1C00, Sync Manager Communication Type .................................................................................................. 8-18
0x1C10 to 0x1C13, Sync Manager PDO Assignment ....................................................................................... 8-19
0x1C32, Sync Manager 2 Synchronization ....................................................................................................... 8-21
0x1C33, Sync Manager 3 Synchronization ....................................................................................................... 8-23
8.5 Manufacturer Specific Objects .......................................................................................................................... 8-25
0x2000, Motor ID ............................................................................................................................................... 8-25
0x2001, Encoder Type ....................................................................................................................................... 8-25
0x2002, Encoder Resolution ............................................................................................................................. 8-25
0x2003, Power Fail Mode .................................................................................................................................. 8-26
0x2004, RST Power Fail Check Time ............................................................................................................... 8-26
0x2005, 7SEG Display Object ........................................................................................................................... 8-26
0x2006, Regenerative Resistor De-rating Factor .............................................................................................. 8-27
0x2007, Regenerative Resistor Value ............................................................................................................... 8-27
0x2008, Regenerative Resistor Capacity .......................................................................................................... 8-27
0x2009, Overload Check Base .......................................................................................................................... 8-27
Table of Contents

0x200A, Overload Warning Level ...................................................................................................................... 8-28
0x200B, PWM Off Delay .................................................................................................................................... 8-28
0x200C, Dynamic Brake Control Mode ............................................................................................................. 8-28
0x200D, Basic Function Configuration .............................................................................................................. 8-29
0x200E, Position Scale Numerator ................................................................................................................... 8-29
0x200F, Position Scale Denominator ................................................................................................................ 8-29
0x2010, Velocity Scale Numerator .................................................................................................................... 8-29
0x2011, Velocity Scale Denominator ................................................................................................................. 8-30
0x2012, Acceleration Scale Numerator ............................................................................................................. 8-30
0x2013, Acceleration Scale Denominator ......................................................................................................... 8-30
0x2015, U Phase Current Offset ....................................................................................................................... 8-33
0x2016, V Phase Current Offset........................................................................................................................ 8-33
0x2017, W Phase Current Offset ...................................................................................................................... 8-33
0x2020, Full Closed Control Mode .................................................................................................................... 8-34
0x2021, External Encoder Pitch ........................................................................................................................ 8-34
0x2022, External Encoder Type ........................................................................................................................ 8-34
0x2023, Dual-Feedback Conversion Level ....................................................................................................... 8-35
0x2024, Dual-Feedback Conversion Filter Time Constant................................................................................ 8-35
0x2025, External Encoder Following Error Window .......................................................................................... 8-35
0x2100, Inertia Ratio Setting ............................................................................................................................. 8-35
0x2101, Position P Gain 1 ................................................................................................................................. 8-36
0x2102, Position P Gain 2 ................................................................................................................................. 8-36
0x2103, The Position Command Filter Time Constant ...................................................................................... 8-36
0x2104, Position Feed-forward Gain ................................................................................................................. 8-36
0x2105, The Position Feed-forward Filter Time Constant ................................................................................. 8-37
0x2106, Speed P Gain 1 .................................................................................................................................... 8-37
0x2107, Speed P Gain 2 .................................................................................................................................... 8-37
0x2108, Speed Integral Time Constant 1 (Speed I Gain 1 Time Constant) ...................................................... 8-37
0x2109, Speed Integral Time Constant 2 (Speed I Gain 2 Time Constant) ...................................................... 8-38
0x210A, The Speed Command Filter Time Constant ........................................................................................ 8-38
0x210B, The Speed Feedback Filter Time Constant ......................................................................................... 8-38
0x210C, The Torque Command Filter Time Constant ....................................................................................... 8-38
0x210D, Conversion Mode ................................................................................................................................ 8-39
0x210E, The Gain Conversion Time ................................................................................................................. 8-40
0x210F, The Resonance Avoidance Operation (Notch Filter Use) ................................................................... 8-40
0x2110, The Resonance Avoidance Frequency (Notch Filter Frequency) ........................................................ 8-40
0x2111, The Resonance Avoidance Range (Notch Filter Bandwidth) ............................................................... 8-40
0x2112, The Velocity Limit Switch ..................................................................................................................... 8-41
0x2113, The Velocity Limit Value ....................................................................................................................... 8-41
0x2114, P Control Conversion Torque (Torque Switch Value) .......................................................................... 8-41
0x2115, The P Control Conversion Speed (Speed Switch Value) ..................................................................... 8-41
0x2116, P Control Conversion Acceleration (Acceleration Switch Value) ......................................................... 8-41
0x2117, P Control Conversion Position Error (Following Error Switch Value) .................................................. 8-41
0x2200, Input Port Define 1 ............................................................................................................................... 8-42
0x2201, Input Port Define 2 ............................................................................................................................... 8-42
0x2202, Output Port Define 1 ............................................................................................................................ 8-42
0x2203, Output Port Define 2 ............................................................................................................................ 8-42
0x2204, The Input Port Logic Set ...................................................................................................................... 8-42
0x2205, The Output Port Logic Set ................................................................................................................... 8-43
0x2206, The Zero Speed Range ....................................................................................................................... 8-43
0x2207, The Break Output Speed ..................................................................................................................... 8-44
Table of Contents

0x2208, The Break Output Delay Time ............................................................................................................. 8-44
0x2300, The Index (Z-phase) Pulse Detection Operation Speed (Index Pulse Search Speed) ....................... 8-44
0x2301, The Speed Command Acceleration Time ............................................................................................ 8-45
0x2302, The Speed Command Deceleration Time ........................................................................................... 8-45
0x2303, The Speed Command S-curve Time ................................................................................................... 8-45
0x2304, The Speed Operation Pattern (Acceleration Pattern) .......................................................................... 8-45
0x2305, The Manual JOG Operation Speed (JOG Speed) ............................................................................... 8-45
0x2306, JOG Operation Speed 1 (Program JOG Speed 1) .............................................................................. 8-46
0x230A, JOG Operation Time 1 (Program JOG Time 1) .................................................................................. 8-46
0x230B, JOG Operation Time 2 (Program JOG Time 2) .................................................................................. 8-47
0x230C, JOG Operation Time 3 (Program JOG Time 3) .................................................................................. 8-47
0x230D, JOG Operation Time 4 (Program JOG Time 4) .................................................................................. 8-47
0x2400, Electric Gear Ratio Mode (Electric Gear Mode) .................................................................................. 8-47
0x2401, The Electric Gear Numerator Offset .................................................................................................... 8-47
0x2402, The Position Limit Function ................................................................................................................. 8-48
0x2403, Backlash Compensation ...................................................................................................................... 8-48
0x2600, The Current Speed (RPM) ................................................................................................................... 8-48
0x2601, The Command Speed (RPM) .............................................................................................................. 8-48
0x2602, The Tracking Position Pulse (Feedback Pulse) .................................................................................. 8-48
0x2603, The Position Command Pulse ............................................................................................................. 8-49
0x2604, The Remaining Position Pulse (Following Error) ................................................................................ 8-49
0x2605, The Input Command Frequency .......................................................................................................... 8-49
0x2606, Current Operation Torque .................................................................................................................... 8-49
0x2607, Current Command Torque ................................................................................................................... 8-49
0x2608, Accumulated Overload ........................................................................................................................ 8-50
0x2609, The Maximum Instantaneous Load ..................................................................................................... 8-50
0x260A, The Torque Limit .................................................................................................................................. 8-50
0x260B, The DC-Link Voltage ........................................................................................................................... 8-50
0x260C, Regenerative Overload ....................................................................................................................... 8-51
0x260D, The Single-turn Data (Pulse) Display (Single-turn Data) .................................................................... 8-51
0x260E, The Single-turn Data (Degree) Display (Single-turn Data (deg)) ........................................................ 8-51
0x2610, The Room Temperature Display .......................................................................................................... 8-51
0x2611, The Motor Rated Speed Display .......................................................................................................... 8-52
0x2612, The Motor Maximum Speed Display ................................................................................................... 8-52
0x2613, The Motor Rated Current Display ........................................................................................................ 8-52
0x2614, The U Phase Current Offset Display ................................................................................................... 8-52
0x2615, The V Phase Current Offset Display ................................................................................................... 8-52
0x2616, The FPGA Version Display .................................................................................................................. 8-53
0x2617, External Encoder Position Feedback .................................................................................................. 8-53
0x2618, External Encoder Following Error ........................................................................................................ 8-53
0x2700, Read/Clear the Alarm History .............................................................................................................. 8-53
0x2701, Auto Gain Tuning (Auto-tuning) ........................................................................................................... 8-54
0x2702, Reset Absolute Encoder ...................................................................................................................... 8-56
0x2703, Calibrate Current Offset ....................................................................................................................... 8-56
8.6 CiA402 Objects ................................................................................................................................................. 8-57
0x603F, Error Code ........................................................................................................................................... 8-57
0x6040, Controlword ......................................................................................................................................... 8-57
Table of Contents

Details on Bits 0 to 3 .......................................................................................................................................... 8-58
Details on Bits 4 to 9 .......................................................................................................................................... 8-58
0x6041, Statusword ........................................................................................................................................... 8-60
0x605A, The Quick Stop Option Code .............................................................................................................. 8-64
0x605B, The Shutdown Option Code ................................................................................................................ 8-65
0x605C, The Disable Operation Option Code ................................................................................................... 8-65
0x605D, The Halt Option Code ......................................................................................................................... 8-66
0x605E, The Fault Reaction Option Code ......................................................................................................... 8-66
0x6060, Modes of Operation ............................................................................................................................. 8-67
0x6061, The Modes of Operation Display ......................................................................................................... 8-67
0x6062, The Position Demand Value ................................................................................................................ 8-68
0x6063, The Position Actual Internal Value ....................................................................................................... 8-68
0x6064, The Position Actual Value .................................................................................................................... 8-68
0x6065, The Position Error Range (Following Error Window) .......................................................................... 8-68
0x6066, Position Error Timeout (Following Error Time Out) ............................................................................. 8-69
0x6067, The Position Reached Range (Position Window) ............................................................................... 8-69
0x6068, The Position Reached Time (Position Window Time) ......................................................................... 8-69
0x606B, The Velocity Demand Value ................................................................................................................ 8-69
0x606C, The Actual Velocity Value .................................................................................................................... 8-69
0x606D, The Velocity Reached Range (Velocity Window) ................................................................................ 8-70
0x606E, The Velocity Window Time .................................................................................................................. 8-70
0x6071, The Target Torque ................................................................................................................................ 8-70
0x6072, Maximum Torque ................................................................................................................................. 8-70
0x6074, The Torque Demand Value .................................................................................................................. 8-71
0x6076, The Motor Rated Torque ...................................................................................................................... 8-71
0x6077, The Torque Actual Value ...................................................................................................................... 8-71
0x607A, The Target Position ............................................................................................................................. 8-71
0x607C, The Home Offset ................................................................................................................................. 8-72
0x607D, The Software Position Limit ................................................................................................................ 8-72
0x607F, Maximum Profile Velocity ..................................................................................................................... 8-73
0x6081, The Profile Velocity .............................................................................................................................. 8-73
0x6083, Profile Acceleration .............................................................................................................................. 8-74
0x6084, Profile Deceleration ............................................................................................................................. 8-74
0x6085, Quick Stop Deceleration ...................................................................................................................... 8-74
0x6087, The Torque Slope ................................................................................................................................ 8-74
0x6098, The Homing Method ............................................................................................................................ 8-74
0x6099, Homing Speeds ................................................................................................................................... 8-75
0x609A, Homing Acceleration ........................................................................................................................... 8-75
0x60B1, The Velocity Offset .............................................................................................................................. 8-76
0x60B2, The Torque Offset ................................................................................................................................ 8-76
0x60B8, The Touch Probe Function .................................................................................................................. 8-76
0x60B9, The Touch Probe Status ...................................................................................................................... 8-77
0x60BA, The Touch Probe 1 Positive Edge Position Value .............................................................................. 8-78
0x60BB, The Touch Probe 1 Negative Edge Position Value ............................................................................. 8-78
0x60BC, The Touch Probe 2 Positive Edge Position Value .............................................................................. 8-78
0x60BD, The Touch Probe 2 Negative Edge Position Value ............................................................................. 8-79
0x60C1, The Interpolation Data Record ............................................................................................................ 8-79
0x60C2, The Interpolation Time Period ............................................................................................................. 8-79
0x60E0, The Positive Torque Limit Value .......................................................................................................... 8-80
0x60E1, The Negative Torque Limit Value ........................................................................................................ 8-80
0x60F4, The Following Error Actual Value ........................................................................................................ 8-80
Table of Contents

0x60FC, The Position Demand Internal Value .................................................................................................. 8-80
0x60FD, The Digital Input .................................................................................................................................. 8-81
0x60FE, The Digital Output ............................................................................................................................... 8-81
0x60FF, The Target Velocity .............................................................................................................................. 8-83
0x6502, Supported Drive Modes ....................................................................................................................... 8-83
9. Handling and Operation .................................................................................................................. 9-1
9.1 Operation Checklist ............................................................................................................................................ 9-1
9.1.1 Wiring Checklist ...................................................................................................................................... 9-1
9.1.2 Drive Signal (CN1) Wiring Checklist ....................................................................................................... 9-1
9.1.3 Surrounding Environment Checklist ....................................................................................................... 9-1
9.1.4 Machine Status Checklist ....................................................................................................................... 9-1
10. Product Specifications .................................................................................................................. 10-1
10.1 The Servo Motor ............................................................................................................................................... 10-1
10.1.1 Product Features .................................................................................................................................. 10-2
10.1.2 Outline Diagram .................................................................................................................................. 10-24
10.2 The Servo Drive .............................................................................................................................................. 10-36
10.2.1 Product Features ................................................................................................................................ 10-36
10.3 Outline Diagram .............................................................................................................................................. 10-38
10.4 Options and Peripheral Devices ..................................................................................................................... 10-40
11. Maintenance and Inspection ........................................................................................................ 11-1
11.1 Maintenance and Inspection ............................................................................................................................. 11-1
11.1.1 Precautions ........................................................................................................................................... 11-1
11.1.2 What to Inspect ..................................................................................................................................... 11-1
11.1.3 Replacing Parts .................................................................................................................................... 11-3
11.2 Diagnosing and Troubleshooting Abnormalities ................................................................................................ 11-4
11.2.1 The Servo Motor ................................................................................................................................... 11-4
11.2.2 The Servo Drive .................................................................................................................................... 11-5
12. Appendix ........................................................................................................................................ 12-1
12.1 Motor Types and IDs ........................................................................................................................................ 12-1
12.2 Test Drive Procedure ........................................................................................................................................ 12-4
1. Product Configuration
1-1
1.1 Product Verification
1. Check the name tag to verify that the product received matches the model ordered.
Does the servo drives name plate match?
Does the servo motors name plate match?
2. Check the product components and options.
Are the type and length of cables correct?
Does the regenerative resistor conform to the required standard?
Is the shape of the shaft correct?
Are there any abnormalities after mounting the oil seal or brake?
Are the gearbox and the gear ratios correct?
Is the encoder format correct?
3. Check the exterior of the device.
Are there any foreign substances or humidity in the device?
Is there any discoloration, contaminant, damage or disconnected wire?
Are the bolts tightly fastened to the joints?
Is there any abnormal sound or excessive friction during operation?
The Servo Drive Product Format

Series
Name

Communication
Type

Input
Voltage
Capacity Encoder Type Option
The Servo
Series

S: Standard I/O
type

N : Network type

A: 220 Vac

B: 400 Vac
001 : 100 W
002 : 200 W
004 : 400 W
008 : 750 W
010 : 1.0 kW
020 : 2.0 kW
035 : 3.5 kW
050 : 5.0 kW
150 : 15.0 kW
B: Serial
(communication-
type)

(Blank)
Standard
product
(Marking)
Exclusive
Option

L7 N A 004 B AA
1-2
Servo Motor Product Format
APM S B 04 A E K 1 G1 03

Motor Shape
S: Real Axis
H: Hollow
Shaft
B: Assembly
F : Flat Type
L : L7 Only
Oil Seal and Brake

Non-existent: None
included
1: Oil Seal attached
2: Brake attached
3: Oil Seal and Brake
attached
Gearbox Specifications

Non-existent: No gearbox
G1: For general industrial
purposes (Floor Mounted)

G2: For general industrial
purposes Flange Mounted)
G3: Precise Gearbox
Motor Capacity
R3 : 30[W]
R5 : 50[W]
01 : 100[W]
02 : 200[W]
03 : 300[W]
04 : 400[W]
05 : 450[W]
06 : 550/600[W]
07 : 650[W]
08 : 750/800[W]
09 : 850/900[W]
10 : 1.0[kW]

150 : 15.0[kW]
220 : 22.0[kW]
300 : 30.0[kW]
370 : 37.0[kW]
Shaft Cross-section

N: Straight
K: One-sided round
key (standard)
D: D Cut
T: Tapering
R: Double-sided round
key
H: Hollow Shaft
Encoder Type
Quadrature (pulse
type)
A: Inc. 1024 P/R
B: Inc. 2000 P/R
C: Inc. 2048 P/R
D: Inc. 2500 P/R
E: Inc. 3000 P/R
F: Inc. 5000 P/R
G: Inc. 6000 P/R
Serial BiSS
(communication type)
N : 19bit S-Turn Abs.
M : 19bit M-Turn Abs.
(18bit SA M-Turn Abs)
Gearbox
classification
03 : 1/3
10 : 1/10
Servo Motor
Rated RPM
A : 3000 [rpm]
D : 2000 [rpm]
G : 1500 [rpm]
M : 1000 [rpm]
Flange Size

A : 40 Flange
B : 60 Flange
C : 80 Flange
D : 100 Flange
E : 130 Flange
F : 180 Flange
G : 220 Flange
H : 250 Flange
J : 280 Flange
1-3
1.2 Parts
1.2.1 Servo Motor Parts
80 Flange or below

80 Flange or below(Flat Type)

130 Flange or higher

Shaft
Flange Frame
Mold Housing Encoder Cover
Power Connector
Encoder Connector
1-4
1.2.2 Servo Drive Parts
L7NA001B, L7NA002B, L7NA004B
Safety connector (CN6)
This connector connects safety
devices.
Note) If you are not using any
safety devices, be sure to install
the safety jump connector on the
L7N.
Input/output signal connector
(CN1)
This connector is for sequence
input/output signals.
Operation keys
These allow you to
check parameters.
Main power connectors (L1,
L2, and L3)
These terminals connect to
the main circuit power input.
DC reactor connectors
These terminals connect to the
DC reactor to suppress high-
frequency power.
(PO and PI)
Short circuit these when not in
use.
Regenerative resistance connectors
(B+, B, and BI)
external regenerative resistor.
- Short B and BI for
basic installations.
- If you are using an external resistor,
connect it to the B+ and B terminals.
CHARGE lamp
This turns on when the main circuit power is on.
It remains turned on as long as an electric charge
is in the L7N condenser, even after the main
circuit power is turned off. Do not touch the power
terminal while turning it on. Doing so may result
in an electric shock.
Control power terminals (C1 and C2)
These terminals are for the control
power input.
Servo motor connecting terminals (U,
V, and W)
These terminals connect to the main
circuit cable (power cable) of the servo
motor.
Ground terminal
The ground terminal prevents electric
shock.
Be sure to connect a grounding line to this
terminal.
Encoder connector (CN2)
This connects to the encoder
installed on the servo motor.
EtherCAT communication port
(output, CN3)
(input, CN4)
Display
This displays numerical values,
such as the L7N state and alarm
number.
USB communication port (CN5)
This port communicates with a
personal computer.
State LEDs
These LED indicate the current
EtherCAT state.

(EtherCAT IN, CN4)
(EtherCAT OUT, CN3)
1-5
L7NA008B,L7NA010B
Operation keys
These allow you to check
parameters.
Main power connectors (L1, L2,
and L3)
main circuit power input.
DC reactor connector (PO and PI)
These terminals connect to the DC reactor
to suppress high-frequency power.
(PO and PI)
Short circuit these when not in use.
Regenerative resistance connectors (B+,
B, and BI)
These terminals connect to the external
regenerative resistor.
- Short B and BI for
basic installations.
- If you are using an external resistor,
connect it to the B+ and B terminals.
CHARGE lamp
This turns on when the main circuit power is on.
It remains turned on as long as an electric charge is in
the L7N condenser, even after the main circuit power is
turned off. Do not touch the power terminal while turning
it on. Doing so may result in an electric shock.
Control power terminals
(C1 and C2)
These terminals are for the
control power input.
Servo motor connecting
terminals (U, V, and W)
These terminals connect to
the main circuit cable
(power cable) of the servo
motor.
Ground terminal
The ground terminal prevents electric
shock.
Be sure to connect a grounding line to
this terminal.
Safety connector (CN6)
This connector connects safety devices.
Note) If you are not using any safety
devices, be sure to install the safety jump
connector on the L7N.
Input/output signal connector
(CN1)
This connector is for
sequence input/output
signals.
Encoder connector (CN2)
This connects to the encoder
installed on the servo motor.
(input, CN4)
Display
This displays numerical values,
such as the L7N state and alarm
number.
USB communication port (CN5)
This port communicates with a
personal computer.
State LEDs
These LED indicate the
current EtherCAT state.
(output, CN3)

(EtherCAT IN, CN4)
(EtherCAT OUT, CN3)
1-6
L7NA020B,L7NA035B

(EtherCAT IN, CN4)
(EtherCAT OUT, CN3)
1-7
L7NA050B

1-8
1.3 Connector Diagram

Note 1) The input signals (DI4~DI8, output signals (DO1~DO4) are the factory default signals.
Note 2) ** is unallocated signals. You can allocate those signals by setting I/O signal allocation.
Refer to 6.3 I/O Contacts parameter setting for more information.
Note 3) Input signal DI7 and DI8 are always allocated as PROBE1, PROBE2 regardless of the
input signal allocation setting.
2. Installation
2-1
2. Installation
2.1 The Servo Motor
2.1.1 Operating Environment
Item Requirements Notes
Ambient
temperature
0 40[ ]
Consult with our technical support team to customize the
product if temperatures in the installation environment are
outside this range.
Ambient
humidity
80% RH or lower Do not operate this device in an environment with steam.
External
vibration
Vibration acceleration
19.6 or below on
both the X and Y axis.
Excessive vibrations reduce the lifespan of the bearings.
2.1.2 Preventing Impact
Impact to the motor during installation or handling may damage the encoder.

2.1.3 Motor Connection
The motor might burn out if it is connected directly to commercial power.
Always connect the motor via the specified drive.
Connect the ground terminals of the motor to either of the two ground terminals inside the drive,
and attach the remaining terminal to the type-3 ground.

Connect the U, V, and W terminals of the motor in the same way as the U, V, and W terminals of
the drive.
Ensure that the pins on the motor connector are securely attached.
In order to protect against moisture or condensation in the motor, make sure that insulation
resistance is 10 (500 V) or higher before installation.
2. Installation
2-2
2.1.4 The Load Device Connection
For coupling connections: Ensure that the motor shaft and load shaft are aligned within the
tolerance range.

For pulley connections:
Flange
Lateral Load Axial Load
Notes
N kgf N kgf
40 148 15 39 4

60 206 21 69 7
80 255 26 98 10
130 725 74 362 37
180 1548 158 519 53
220 1850 189 781 90
2.1.5 Cable Installation
For vertical installations, make sure that no oil or water flows into the connecting parts.

Do not apply pressure to or damage the cables.
Use robot cables to prevent swaying when the motor moves.

Load shaft
Motor shaft
0.03 or below (peak to peak)
0.03 or below (peak to peak)
Nr: 30 or below
Lateral load
Axial load
2. Installation
2-3
2.2 The Servo Drive
2.2.1 Operating Environment
Item Requirements Notes
Ambient
temperature
0 50[ ]
Caution
Install a cooling fan on the control panel to maintain
an appropriate temperature.
Ambient
humidity
90% RH or lower
Caution
Condensation or moisture may develop inside the drive during
prolonged periods of inactivity and damage it.
Remove all moisture before operating the drive after a
prolonged period of inactivity.
External
vibration
Vibration
acceleration 4.9
or lower
Excessive vibration reduces the lifespan of the machine and
may cause malfunctions.
Ambient
conditions
Do not expose the device to direct sunlight.
Do not expose the device to corrosive or combustible gases.
Do not expose the device to oil or dust.
Ensure that the device receives sufficient ventilation.

2. Installation
2-4
2.2.2 Wiring the Control Panel
Comply with the spacing specified in the following figures when installing the control panel.

Caution
Ensure that during installation the heat from the external regenerative resistor does not affect
the drive.
Ensure that the servo drive control panel is flat against the wall during installation.
Ensure that the metal powder from drilling does not enter the drive when assembling the control
panel.
Ensure that oil, water, and metal dust do not enter the drive through gaps in the casing.
Protect the control panel by spraying compressed air in areas which accumulate harmful gases
or dust.

2. Installation
2-5
2.2.3 Power Supply Wiring
Ensure that the input power voltage is within the acceptable range.
Caution
Overvoltage can damage the drive.
Connecting commercial power to the U, V and W terminals of the drive may damage the drive.
Always supply power via the L1, L2 and L3 terminals.
Connect short-circuit pins to the B and BI terminals. For external regenerative resistors, remove the
short-circuit pins and use standard resistors for the B+ and B terminals.
Model
Resistance
Value
Standard
Capacity
* Notes
L7NA001B
100 Built-in 50 W
Caution
For information about resistance during
regenerative capacity expansion, refer to
Section 9.3, "Otional and Peripheral Devices.
L7NA002B
L7NA004B
L7NA008B
40 Built-in 100 W
L7NA010B
L7NA020B
13 Built-in 150 W
L7NA035B
Configure the system so that the main power (L1, L2, L3) is supplied after the control power (C1,
C2). (Refer to Chapter 3, "Wring.)
High voltages may remain in the device for sometime even after the main power is disconnected.
Warning
After disconnecting the main power, ensure that the charge lamp is off before you start wiring.
Failure to do so may result in electric shock.
Always ground the device over the shortest possible distance.
Long ground wires are susceptible to noise which may cause the device to malfunction.

3. Wiring
3-1
3. Wiring
3.1 Internal Diagram
3.1.1 L7N Drive Block Diagram [L7NA001B - 7NA004B]

Note 1) If using a DC reactor, connect the PO and PI pins.
Note 2) If using an external regenerative resistor, remove the B and BI short-circuit pins and connect the
B+ and B pins.
3. Wiring
3-2
3.1.2 L7N Drive Block Diagram [L7NA008B - 7NA035B]
Main Control
(1Points)
Safety Function Output
DC Voltage
EtherCAT
Communication
U and V Current
Diode
L3
AC200~230V
Three-Phase Power Input
L1
L2
Lamp
Chage
Thermister
Input
P/C Insulation I/F
Upper Controller Connection (CN1)
Contact Input
(8 Points) (4 Points)
Contact Output
POWER Circuit Access
DSP / FPGA
Encoder CN2
M
IGBT
Regenerative
W
Current Sensor
U
V
B B+ BI
E
PO PI
Note 1)
Note 2)
C1
C2
S
M
P
S
T1 T2
Thermister
Single-Phase Power Input
AC200~230V
USB
CN5
CN3,CN4
USB TO UART
BiSS
Thermister
Control Power Failure
Detection Circuit
Main Power
Safety Function Input
Safety Device Connection (CN6)
ESC
A/D Conversion
Resistor
Failure
Detection Circuit
Internal
Temperature
Detection Circuit
Relay
Operation
Circuit
DC Voltage
Detection
Circuit
Regenerative
Breaking
Operation
Circuit
IGBT
Temperature
Detection
Circuit
PWM Signal
SC Detection
Circuit
U and V Current
Detection
Circuit
DB
Operation
Circuit
(2 Points)
Communication
Note 3)
Cooling Fan
N

B+ and B pins.
Note 3) The L7NA008B ~ L7NA035B modesl are cooled by a DC 24V cooling fan.

3. Wiring
3-3
3.1.3 L7N Drive Block Diagram [L7NA050B]
Main Control
(1Points)
Safety Function Output
DC Voltage
EtherCAT
Communication
U and V Current
Diode
L3
AC200~230V
Three-Phase Power Input
L1
L2
Lamp
Chage
Thermister
Input
P/C Insulation I/F
Upper Controller Connection (CN1)
Contact Input
(8 Points) (4 Points)
Contact Output
POWER Circuit Access
DSP / FPGA
Encoder CN2
M
IGBT
Regenerative
W
Current Sensor
U
V
B B+ BI
E
PO PI
Note 1)
Note 2)
C1
C2
S
M
P
S
T1 T2
Thermister
Single-Phase Power Input
AC200~230V
USB
CN5
CN3,CN4
USB TO UART
BiSS
Thermister
Control Power Failure
Detection Circuit
Main Power
Safety Function Input
Safety Device Connection (CN6)
ESC
A/D Conversion
Resistor
Failure
Detection Circuit
Internal
Temperature
Detection Circuit
Relay
Operation
Circuit
DC Voltage
Detection
Circuit
Regenerative
Breaking
Operation
Circuit
IGBT
Temperature
Detection
Circuit
PWM Signal
SC Detection
Circuit
U and V Current
Detection
Circuit
DB
Operation
Circuit
(2 Points)
Communication
Note 3)
Cooling Fan
N

B+ and B pins.
Note 3) The L7NA050B model is cooled by a DC 24V cooling fan.

3. Wiring
3-4
3.2 Power Supply Wiring
3.2.1 L7N Drive Wiring Diagram [L7NA001B - 7NA035B]

Note 1) It takes approximately one to two seconds to output an alarm signal after turning on the main
power. Accordingly, press and hold the main power ON switch for at least two seconds.
Note 2) Check the B and BI short-circuit terminals and the L7NA001B-L7NA004B (50 W, 100 ),
L7NA008B ~ L7NA010B (100 W, 40 ), and L7NA020B ~ L7NA035B (150 W, 13 ) regenerative
resistors before use. If the regenerative capacity is high because of frequent acceleration and
deceleration, open the short-circuit pins (B, BI) and connect an external regenerative resistor to B
and B+.
Note 3) Remove approximately 7-10 of the sheathing from the cables for the main circuit power and
attach crimp terminals. (Refer to Section 3.2.2, "Pwer Circuit Electrical Components.)

Note 4) Press the button on the L7NA001B-L7NA010B drive terminal to attach or remove wires to the
main circuit power unit. For the L7NA020B ~ L7NA035B drive, use a (-) flathead screwdriver to
attach or remove the wires.

3. Wiring
3-5
3.2.2 L7 Drive Wiring Diagram [L7N050B]
U
V
W
L1
L2
L3
C1
C2
B+
B
38
39
CN1
RA
M
E
Alarm-
Alarm+
1Ry
RA
1SK
1Ry 1MC
+24V
NF
1MC
R S T (200~230V)
Main
OFF
Main
ON
Encoder
(Note1)
(Note2)
PO PI
DC Reactor
external
regenerative
resistance
Servo Drive

1) It takes approximately one to two seconds to output an alarm signal after turning on the main power.
Accordingly, press and hold the main power ON swithch for at least two seconds.
2) Check the status of connection of internal regenerative resistnace (B+. B) before using because
L7NA050 (120[W], 6.8[ ]) has internal regenerative resistance. If the value of regenerative voltage is too
high by frequent deceleration and acceleration, install external regenerative resistnace on B and B+
terminal after attatching internal regenerative resistance connected B+, B to NC hole on the case.

3. Wiring
3-6
3.2.3 Power Circuit Electrical Components
Name L7NA001B L7NA002B L7NA004B L7NA008B L7NA010B L7NA020B L7NA035B L7NA050B
MCCB(NFB)
30A Frame 5A
(ABE33b/5)
30A Frame
10A
(ABE33b/10)
30A Frame 15A
(ABE33b/15)
30A Frame 30A
(ABE33b/30)
50A Frame
40A(ABE53b/40)
Noise Filter (NF) TB6-B010LBEI(10A) TB6-B030NBDC(30A)
TB6-
B040A(40A)
DC reactor HFN-10(10A) HFN-15(15A) HFN-30(30A)
HFN-40(40A)
MC
11A / 240V
(GM-9)
18A / 240V
(GM-18)
32A / 240V
(GM-32)
50A / 240V
(GM-50)
Wire
(Note1)
L1,L2
,L3,
PO,PI
,N,B+
,B,BI,
U,V,
W
AWG16
(1.5 )
AWG14
(2.5 )
AWG12
(4.0 )
AWG10 (6.0 )
C1,
C2
AWG16(1.5 ) AWG16(1.5 ) AWG16(1.5 )
AWG16(1.5 )
Crimp terminal
UA-F1510, SEOIL
(10mm Strip & Twist)
UA-F2010, SEOIL
UA-F4010, SEOIL
GP110028
KET
Regenerative
resistor
(Default)
50 W
100
100 W
40
150 W
13
120[W]
6.8
Connector
(L1,L2..IV,W)
BLF 5.08/03/180F SN BK BX
BLF 5.08/11/180F SN BK BX
BLZ7.62HP/03/180LR
SN BK BX SO
BLZ7.62HP/11/180LR
SN BK BX SO

Note1) Use 600V-PVC Insulated wire for wiring.
Use approved UL wire (Temp. 60 or above) for UL(CSA) Regulation.
Use approved wire for any other regulations.
Use equivalent or above components compare to components above for any special applications.

3. Wiring
3-7
(L7NA004B or below)

(L7NA008B ~ L7NA010B)
A B
C

0. 6 3. 5
100
Length of strip
7~10[ ]
0.4~0.5[Nm]
Weidmuellers
SD 0.6x3.5x100
M4 : 1.2[Nm]
Length of strip
7~10[ ]
0.4~0.5[Nm]
M4 : 1.2[Nm]
Weidmuellers
SD 0.6x3.5x100
3. Wiring
3-8
(L7NA020B ~ L7NA035B)
A B
C

1) Refer to the drawings above for wiring with BLF 5.08 or BLZ 7.62HP Series connector.
2) Insert wire into wire-hole when upper screw is untightened and then, use appropriate (-) shaped
screwdriver with 0.4 ~ 0.5[N.m] torque to make tight completely.
3) Cut by vibration, malfunction or fire by short could be occurred if torque of screwing was not enough.
4) Make tight completely by using hooks both sides when connectors are attached to servo drive after
wiring.
5) FG screw which is located the bottom of servo drive has to be M4 and put on the FG screw with
1.2[N.m] torque.
6) Malfunction of drive could be occurred if torque of screwing was not enough.
7) Recommended (-)shaped screwdriver: Weidmuellers SD 0.6x3.5x100.

Length of strip
7~10[ ]
0.4~0.5[Nm]
M4 : 1.2[Nm]
Weidmuellers
SD 0.6x3.5x100
3. Wiring
3-9
(L7NA050B)

0- Malfunction of drive could be occurred if torque of screwing was not enough.

TB1
L1 L2 L3 B+ B U V W FG FG

TB2
N PO P1

TB3
C1 C2
3. Wiring
3-10
3.3 Timing Diagram
3.3.1 Timing Diagram During Power Input
For the L7N Series, connect single-phase power to the C1 and C2 terminals to supply power
to the control circuit, and three-phase power to L1, L2, and L3 to supply power to the main
circuit.
The servo signal becomes Ready after the maximum period of 120 ms that is required to
reset the device elapses. If you change the signal to ON, the servo operates in 40 ms.

Note 1) The Servo Ready turns on after the main power is established and the control program is reset.
Note 2) Servo On begins after the Servo Ready is on and the EtherCAT communication and the servo are
synchronized.

Control power
established 5 V
Control
program reset
Main power
Alarm
(Normally On)
Servo Ready
Servo On
Clear the DB
PWM output
(motor rotation)
150 ms 50 ms
120 ms
10 ms
10 ms
5 ms
40 ms
Main power,
control power
200 ms
2 ms
3. Wiring
3-11
3.3.2 Timing Diagram During an Alarm Trigger
When an alarm is triggered in the servo drive, it blocks the PWM and stops the motor.
Caution
Reset the alarm after solving the problem that triggered the alarm and after changing the
command signal (Servo On) to Off.

200 ms
Control power
established
5 V
Control
program reset
Main power
Alarm
(Normally On)
Servo RDY
Servo On
Clear the DB
PWM
(Motor rotation)
RESET
150 ms
40 ms
10 ms
5 ms
2 ms 30 ms
Alarm triggered by
an anomaly
Remove the
causes that
triggered the
alarm
Main power,
control power
supply
3. Wiring
3-12
3.4 Wiring the Control Signals
3.4.1 The Contact Input Signal
Caution
1. There are two input contacts based on the characteristics of the A and B contact signals.
Configure them in accordance with the input signal logic definition (0x2204).
2. Change the signal definition for each contact in accordance with the input signal definition
(0x2200, 0x2201).

R1: 3.3 K, R2: 680
3.4.2 The Contact Output Signal
Caution
1. There are two input contacts based on the characteristics of the A and B contact signals.
Configure them in accordance with the output signal logic definition (0x2205).
2. Change the signal definition for each contact in accordance with the output signal definition
(0x2202, 0x2203).
3. Overvoltage or over currents may damage the device because it uses an internal transistor
switch.
Rated voltage and current: DC 24 V 10%, 150

Note 1) The alarm and READY output signals are separate in the GND24 terminal.

3. Wiring
3-13
3.5 Connecting Serial Encoder Signals (CN2)
3.5.1 APCS-ECS Cable

3.5.2 APCS-EDS Cable

Servo drive Servo motor
MA
/MA
SL
/SL

+5V
GND
SHD
Encoder
Frame
Cable
Connector(CN2)
Maker-3M
10314-52A0-008
10114-3000VE
AWG24 4Pair Twist
Shield Wire
Cable
Connector
Maker-AMP
172161-1
170361-1
SHD Frame
Cable
Connector(CN2)
Maker-3M
10314-52A0-008
10114-3000VE
Cable
Connector
MS3108B20-29S
AWG24 4Pair Twist
Shield Wire
3. Wiring
3-14
3.5.3 APCS-EES Cable

Servo motor
1
6
2
7

9
4

5
MA
/MA
SL
/SL

5V
GND

SHD
Connector
Tyco Connector
(7Ciruits)
3
4
5
6

14
7

Frame
Servo drive
Cable
Connector(CN2)
Maker 3M
10314-52A0-008
10114-3000VE
AWG24 4Pair Twist
Shield Wire
3. Wiring
3-15
3.6 Connecting Multi-turn Encoder Signals (CN2)
3.6.1 APCS-ECS1 Cable
3.6.2 APCS-EDS1 Cable
A
B
C
D
E
F

H
G

J
MA
/MA
SL
/SL
BAT+
BAT-

5V
GND

SHD
Cable
Connector(CN2)
Maker - 3M
10314-52A0-008
10114-3000VE
Cable
Connector
MS3108S20-29S
Encoder
3
4
5
6

14
7

Frame
1
2
3
4
5
6

7
8

9
MA
/MA
SL
/SL
BAT+
BAT-

5V
GND

SHD
Cable
Connector(CN2)
Maker - 3M
10314-52A0-008
10114-3000VE
Cable
Connector
172161-1(AMP)
170361-1(AMP)
Encoder
3
4
5
6

14
7

Frame
AWG24 4Pair Twist
Shield Wire
Servo motor
Servo drive
AWG24 4Pair Twist
Shield Wire
3. Wiring
3-16
3.6.3 APCS-EES1 Cable
1
6
2
7
8
3

9
4

5
MA
/MA
SL
/SL
BAT+
BAT_

5V
GND

SHD
Cable
Connector(CN2)
Maker - 3M
10314-52A0-008
10114-3000VE
Connector
Tyco Connector
(7Ciruits)
Encoder
3
4
5
6

14
7

Frame
AWG24 4Pair Twist
Shield Wire
3. Wiring
3-17
3.7 Connecting the Input/Output Signals
3.7.1 The Names and Functions of the Input Signals
(CN1)
Pin Number Name Details Function
7 /N-OT
Reverse (CW)
rotation prohibited
The actuator stops the servo motor to
prevent it from moving beyond the motion
range.
8 /P-OT
Forward (CCW)
rotation prohibited
11 HOME Origin sensor
Connects the origin sensor to return to the
origin.
12 ALMRST Alarm reset Deactivates the servo alarm.
13 PCON P control action
When the contact is on, the speed control
loop transfers the mode from PI control to P
control.
14 GAIN2
Transfer of the
gain 1 and gain 2
When gain 2 contact is ON, it transfers from
gain 1 to gain 2.
9
Note 1)
/PROBE1 Touch probe 1
The probe signal to rapidly store the
position value.
10
Note 1)
/PROBE2 Touch probe 2
Note 1) You cannot map touch probe signals.
3.7.2 The Names and Functions of the Output Signals
(CN1)
Pin Number Name Details Function
1 BRAKE+
Brake
Outputs signals to control the brake when
the servo is turned on or off.
2 BRAKE-
3 ALARM+
Alarm Outputs a signal when an alarm occurs.
4 ALARM-
17 /READY+
Servo Ready
This signal is output when the main power
is established and the preparations for
servo operation are complete.
18 /READY-
19 /ZSPD+
Zero speed
reached
Outputs a signal when the current speed
drops below the zero speed.
20 /ZSPD-
Allocated INPOS Location reached
Outputs a signal when the device reaches
the specified location.
Allocated INSPD Speed reached
Outputs a signal when the device reaches
the specified speed.
Allocated WARN Warning Outputs warning signals.

3. Wiring
3-18
3.7.3 Layout of the Input/Output Signal Connectors

3.7.4 The Names and Functions of Safety Function
Signals (CN6)
PinNumber Name function
3 /HWBB1-
For hard-wired base block inputs
Performs a base block (block torque) on signal off.
4 /HWBB1+
5 /HWBB2+
6 /HWBB2-
7 EDM+
Outputs the pilot circuit status.
8 EDM-
3.7.5 The Connector Layout of Safety Function
Signals (CN6)

Note 1) Never use this on a blank terminal because it is connected to an internal circuit.

3. Wiring
3-19
0- How to use Safety Function Signal (CN6) How to use L7N STO Plug
Dummy

Plug Connector Kit : 2040008-1(TE)
Name of product : APC-CN6J

2) How to use EMG Signal on MAIN

3. Wiring
3-20
3.7.6 Operation Method of Safety Function Signals
(CN6)
Setting /HWBB1 /HWBB2 EDM STO State
1 OFF OFF ON STO
2 ON OFF OFF STO
3 OFF ON OFF STO
4 ON ON OFF Normal State

3. Wiring
3-21
3.8 EtherCAT Connection Example
3.8.1 Example Connection
The following figure shows the connection between a master and slave using EtherCAT
communication.
EtherCAT master
Slave axis 1 Slave axis 2 Slave axis n
Slave axis 1 + Slave axis 2 + + Slave axis n

3. Wiring
3-22
3.8.2 EtherCAT Connectors and the Pin Map
The L7N drive uses CN4 and CN3 as I/O Connector for EtherCAT.
Connector Function
CN4 The EtherCAT input
CN3 The EtherCAT output
Pin Number Signal Name Line color
1 TX/RX0 + White/Orange
2 TX/RX0 - Orange
3 TX/RX1+ White/Green
4 TX/RX2 - Blue
5 TX/RX2 + White/Blue
6 TX/RX1 - Green
7 TX/RX3 + White/Brown
8 TX/RX3 - Brown
Plate Shield
Note 1) EtherCAT only uses signals from the No. 1, 2, 3, and 6 wires.
Note 2) Recommended Connector : STP CAT.5E RJ-45 8P8C
Recommended Cable: CAT.5 STP

4. How to use the Loader
4-1
4.1 Name and Function of each parts

Refer to 5.3 LED State for more information.
Display 5-digit FND Data
Botton for moving
FND Object
Display State of
EtherCAT Comm.
or Error
Display decimal point
16Bit : Display
32Bit : Display dot
4-1
4.2 Status Summary Display
(1) Display Status Summary for CSP Mode
Example of state of Servo Off in CSP Mode
DIGT3~1 :
bb OFF
run ON
Pot CCW Limit
not CW Limit
DIGT4_: ZSPD
DIGT4_: INSPD or INPOS
DIGT4_: Command(or )
DIGT4_DOT : READY
DIGT5 :
P Profile Position, Interpolated Position, Cyclic Sync Position
S Profile Velocity, Cyclic Sync Velocity
T Torque Profile, Cyclic Sync Torque
H Homing mode
DIGIT5_: Init state
DIGIT5_,: Pre-Operational state
DIGIT5_,,: Safe-Operational state

Example of state of Servo On in CSP Mode

DIGT3~1 : Display Current state
bb - Servo Off
run - Servo On
Pot - CCW Limit
not CW Limit
DIGT4_Upper : ZSPD
DIGT4_Middle : INSPD or INPOS
DIGT4_Lower : Command(Speed or Torque) State
DIGT4_DOT : READY State
DIGT5 : Display current control mode.
P - Profile Position, Interpolated Position, Cyclic Sync Position
S - Profile Velocity, Cyclic Sync Velocity
T Torque Profile, Cyclic Sync Torque
H Homing mode
DIGIT5_Lower : Init state
DIGIT5_Middle, Lower : Pre-Operational state
DIGIT5_Upper, Middle, Lower : Safe-Operational state
4-2
(2) Chart of status summary for Servo operation.
Refer to chart below for status summary for Servo operation.

Display of DIGT5 Function Note

Disconnect STO Connector.

Init state.

Pre-Op state.

Safe-Op state.

Servo OFF state in PP, IP or CSP Mode.

Servo ON state in PP, IP or CSP Mode.

CCW Limit state in PP, IP or CSP Mode.

CW Limit state in PP, IP or CSP Mode.

Servo OFF state in PV or CSV Mode.

Servo ON state in PV or CSV Mode.

CCW Limit state in PV or CSV Mode.

CW Limit state in PV or CSV Mode.

Servo OFF state in TQ or CST Mode.

Servo ON state in TQ or CST Mode.

CCW Limit state in TQ or CST Mode.

CW Limit state in TQ or CST Mode.

Servo OFF state in Homing Mode.

Servo ON state in Homing Mode.

CCW Limit state in Homing Mode.

CW Limit state in Homing Mode.
4-3
4.3 Display FND Output Object
(1) How to use the button on loader

When clicking the button, display of FND will move to next object and display value of that object.
If holding down the button while number of object is displayed, it will move to state of FND
default.(ex : P-bb, Servo OFF state in Position control Mode)
Object address which is displayed on FND is from 2600 up to 2616. Those data cannot be modified
by button.
- Click the button.
- Move to next object.
- Holding down the button.
- Move to state of FND default.
Value of 2600
Value of 2601
Value of 2615
Value of 2616
5. EtherCAT Communication
5-1
EtherCAT stands for Ethernet for Control Automation Technology. It is a communication
method for masters and slaves which uses Real-Time Ethernet, developed by the German
company BECKHOff and managed by the EtherCAT Technology Group (ETG).
The basic concept of the EtherCAT communication is that, when a DataFrame sent from a
master passes through a slave, the slave inputs the received data to the DataFrame as soon
as it receives the data.
EtherCAT uses a standard Ethernet frame compliant with IEEE802.3.
Since it is based on a 100BASE-TX Ethernet, cable lengths of up to 100 meters are possible
and the maximum number of connected slaves is 65,535, so it is possible to configure a
nearly unlimited network size. In addition to this, when using a separate Ethernet switch, you
can interconnect it to common TCP/IP.
5.1 The Structure of CANopen over EtherCAT

The L7N drive uses a CiA 402 drive profile. The Object Dictionary in the application layer
includes application data and PDO mapping information from the process data interface and
application data.
The Process Data Object (PDO) consists of an Object Dictionary that can be mapped to the
PDO, and the content of the process data is defined by PDO mapping.
The process data communication is able to periodically read and write the PDO. Mailbox
communication can aperiodically read and write all of the Object Dictionaries.

5-2
5.2 The EtherCAT State Machine

State Details
Init
Resets a device.
Unable to perform mailbox or process data communication.
Pre-Operational Able to perform mailbox communication.
Safe-Operational
Able to read the PDO input data (TxPDO).
Unable to receive PDO output data (RxPDO).
Operational
Performs periodical I/O communication and it is possible to process PDO
output data (RxPDO).
Transition State Details
IP Begins mailbox communication.
PI Stops mailbox communication.
PS Begins input data updates.
SP Stops input data updates.
SO Begins output data updates.
OS Stops output data updates.
OP Stops input/output data updates.
SI Stops input data updates and mailbox communication.
OI Stops both input/output data updates and mailbox communication.

5-3
5.3 LED State
The LEDs on the operating panel of the L7N drive indicates EtherCAT communication and
error statuses, as shown in the following figure.

The L/A IN and L/A OUT (Link Activity) LEDs
The L/A IN LED and L/A OUT LEDs indicate the status of the CN4 and CN3 communication
ports respectively. The following table outlines what each LED state indicates.
Link/Activity LED Description
Off Not connected for communication.
Flickering
Connected, and communication is enabled.

On Connected, but communication is disabled.
RUN LED
Indicates the status of the L7N in the EtherCAT State Machine.
RUN LED Description
Off The L7N is in the INIT state.
Blinking
The L7N is in the Pre-Operational state.

Single Flash
The L7N is in the Safe-Operational state.

On The L7N is in the Operational state.

L/A IN L/A OUT RUN ERR
5-4
The ERR (Error) LED
The ERR LED indicates the EtherCAT communication status. The following table outlines
what each LED state indicates.
ERROR LED Description
Off EtherCAT communication is normal.
Flickering
A booting error occurred.

Blinking
The object setup command received from the EtherCAT master cannot be
performed in the current state.

Single Flash
The state has changed without a command from the EtherCAT master due to a
L7N drive sync error.

Double Flash
A watchdog error occurred during EtherCAT communication.

On A serious problem occurred in the internal communication of the L7N drive.
5.4 Data Type
The following table outlines the content and range of the data types used in this manual.
Name Description Range
SINT Signed 8-bit -128 ~127
USINT Unsigned 8-bit 0 ~ 255
INT Signed 16-bit -32768 ~ 32767
UINT Unsigned 16-bit 0 ~ 65535
DINT Signed 32-bit -21247483648 ~ 21247483647
UDINT Unsigned 32-bit 0 ~ 4294967295
STRING The String Value

5-5
5.5 PDO Mapping
The EtherCAT uses the Process Data Object (PDO) to perform real-time data transfers.
There are two types of PDOs: RxPDO receives data transferred from the upper level
controller, and TxPDO sends the state from the drive to the upper level controller.
The L7N uses 0x1600 to 0x1603 for RxPDO mapping and 0x1A00 to 0x1A03 for TxPDO
mapping. You can map up to 10 objects on each PDO.
The following figure shows an example of PDO mapping.
Index Sub Name Data Type
0x6040 - Controlword UINT
0x607A - Target Position DINT

Index Sub Name Data Type
0x6041 - Statusword UINT
0x6064 - Position Actual Value DINT
0x606C - Velocity Actual Value DINT

5-6
The SyncManager can be composed of multiple PDOs. SyncManager PDO Assign Object
(RxPD:0x1C12, TxPDO:0x1C13) indicates the relationship between the SyncManager and
the PDO.
The following figure shows the SyncManager PDO mapping.

L7N PDO Mapping
The following tables list the default PDO mapping set in the L7N. These settings are defined
in the EtherCAT Slave Information file (XML file).
1
st
PDO Mapping

2
nd
PDO Mapping

3
rd
PDO Mapping

5-7
4
th
PDO Mapping

5-8
5.6 Synchronization Using the DC
(Distributed Clock)
The Distributed Clock (DC) synchronizes EtherCAT communication. The master and slave
share a reference clock (system time) for synchronization, and the slave synchronizes its
applications with the Sync0 event generated by the reference clock.
The following synchronization modes exist in the L7N. You can change the mode with the
sync control register.
Free-run mode
In free-run mode, the L7N operates each cycle independently from the communication cycle and
master cycle.
DC Synchronous Mode
In DC Synchronous mode, the Sync0, event from the EtherCAT master, synchronizes the drive.
Master Application Master
Slave
Master Application
Frame U U
U U
Frame U
U
Sync0
Event
Sync0
Event
Sync0
Event
Cycle time (0x1C32:02) Cycle time (0x1C32:02)
Master user
shift time
Sync0 shift time
Shift time (0x1C33:03)
Calc + Copy time
(0x1C33:06)
Shift time (0x1C32:03)
Calc + Copy time
(0x1C32:06)
Inputs Latch
Outputs Latch

5-9
Index 0x1C32 Sync Manager 2 (Process Data Output) Synchronization
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 10 USINT RO No - - -
Synchronization modes
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0: Free-Run UINT RO No - -
Cycle time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2
Time between Sync0
events [ns]
UDINT RO No - - -
Shift time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
3 125000 [ns] UDINT RO No - -
Synchronization modes supported
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
4
Synchronization mode
Bit 0 = 1: Free-Run
supported Bit 4:2 = 001:
DC Sync0 supported Bit
6:5 = 00:
No Output Shift sup-
ported
UINT RO No - - -
Minimum cycle time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
5 62500 [ns] UDINT RO No - -
Calc and copy time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
6 62500 [ns] UDINT RO No - - -
Delay time
5-10
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
9 0 [ns] UDINT RO No - - -
Index 0x1C33 Sync Manager 3 (Process Data Intput) Synchronization
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change
0 10 USINT RO No -
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change
1 same as 0x1C32:01 UINT RO No -
Cycle time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change
2 same as 0x1C32:02 UDINT RO No -
Shift time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change
3
125000*n [ns]
(n = 1, 2, 3...) Range: 0 to
(Sync0 event cycle time
125000)
UDINT RO No -
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change
4
Bit 0 = 1
: Free-Run supported Bit
4:2 = 001
: DC Sync0 supported
Bit 6:5 = 01
: Input Shift with local
timer supported
UINT RO No -
Minimum cycle time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change
5 same as 0x1C32:05 UDINT RO No - -
5-11
5.7 Emergency Messages
Emergency messages appear as a L7N alarm or a warning passed to the master via mailbox
communication. Emergency messages may not be sent in the event of communication
failure.
Emergency messages consist of 8-byte data.
Byte 0 1 2 3 4 5 6 7
Details
Emergency
error code
(0xFF00)
Error register
(0x1001)
Reserved
Unique field for each manufacturer
L7N alarm code Reserved

5. CiA402 Drive Profile
6-1
6.1 The State Machine
NotreadytoSwitchon
SwitchonDisabled
Start
Quickstopactive
Error occures
(A) : Low-level power
Control power is on. The main
power can be turned on.
(B) : High-level power
Both control power and main power are
on. Torque cannot be applied to the
motor.
(C) : Torque
Torque can be applied to the motor.
Powerofforreset
State Additional state
State
State changed by the
slave
State that can be
checked by the master
1
0
2
3
6
10
4
5
7
8 9
11
12
13
14
15
16

State Details
Not ready to switch on Reset is in progress by control power on.
Switch on disabled
Reset is complete. You can set servo parameters.
However, you cannot supply main power at this time.
Ready to switch on
Main power may be turned on. You can set servo parameters.
Drive function is disabled.
Switched on
Main power is on. You can set servo parameters.
Drive function is disabled.
Operation enabled
Unless in a fault state, the drive functions correctly and torque can be
applied to the motor. You can also set servo parameters.
Quick Stop active
A quick stop function has been performed.
You can set servo parameters.
Fault reaction active
In a Quick Stop or a fault state due to the servo.
Fault
A fault reaction has been processed. Drive function is deactivated.

6-2
State Machine Control Commands
Command
Controlword bits (0x6040)
State Machine
Movement
Bit 7 Bit 3 Bit 2 Bit 1 Bit 0
Shutdown 0 - 1 1 0 2, 6, 8
Switch on 0 0 1 1 1 3
Switch on
+ Enable operation
0 1 1 1 1 3 + 4
Disable voltage 0 - - 0 - 7, 9, 10,12
Quick stop 0 - 0 1 - 7, 10,11
Disable operation 0 0 1 1 1 5
Enable operation 1 1 1 1 1 4, 16
Fault reset 0 1 - - - - 15
Statusword Bit Names (0x6041)
Bit No. Data Description Note
0 Ready to switch on
For more information, refer to 7.6 CiA 402 Objects.
1 Switched on
2 Operation enabled
3 Fault
4 Voltage enabled
5 Quick stop
6 Switch on disabled
7 Warning
8 -
9 Remote
10 Target reached
11 Internal limit active
12
Operation mode specific
13
14 Torque limit active
15 -

6-3
Related Objects
Index Sub Name
Data
Type
Access
PDO
Mapping
Units
0x6040 - Controlword UNIT RW Yes -
0x6041 - Statusword UINT RO Yes -
0x605A -
Quick Stop option code
(Quick Stop Option Code)
INT RW No -
0x605B -
Shutdown option code
(Shutdown Option Code)
INT RW No -
0x605C -
Disable Operation option code
(Disable Operation Option Code)
INT RW No -
0x605D -
Halt option code
(Halt Option Code)
INT RW No -
0x605E -
FAULT reaction option code
(Fault Reaction Option Code)
INT RW No -

6-4
6.2 Operation Modes
The L7N supports the following operation modes (0x6060):
Profile Position Mode
Homing Mode
Interpolated Position Mode
Profile Velocity Mode
Profile Torque Mode
Cyclic Synchronous Position Mode
Cyclic Synchronous Velocity Mode
Cyclic Synchronous Torque Mode
Related Objects
Index Sub Name
Data
Type
Access
PDO
Mapping
Units
0x6060 -
Drive Mode
(Modes of Operation)
SNIT RW Yes -
0x6061 -
Display the operation mode
(Modes of Operation Display)
SNIT RO Yes -
0x6502 -
Supported drive modes
(Supported Drive Modes)
UDINT RO No -
Dynamic Conversion of Operation Modes
The 0x6060 object can change the operation mode. The master simultaneously selects an
operation mode and changes the related objects. When the master switches to a new
operation mode, the L7N instantly switches to that mode.

6-5
6.3 Position Control Modes
6.3.1 Profile Position Mode
Profile Position Mode drives to a target position using the profile speed (0x6081) and profile
acceleration (0x6083, 0x6084).
The Profile Position Mode Block Diagram
Target position (0x607A)
Software position limit (0x607D)
Profile velocity (0x6081)
Max. profile velocity (0x607F)
Profile acceleration (0x6083)
Profile deceleration (0x6084)
Quick Stop deceleration (0x6085)
Position scale
numerator/denominator
(0x200E/0x200F)
Speed scale numerator/
denominator
(0x2010/0x2011)
Acceleration/
deceleration scale
(0x2012/0x2013)
[Posunit]
[Velunit]
[Accunit]
Position
trajectory
generator
[pulse]
[pulse/s]
Controlword(0x6040)
Quick Stop option code (0x605A)
Position
demand
internal value
(0x60FC)
[pulse/s
2
]
OPMode:ProfilePosition
1

Position
controller
Speed
controller
Torque
controller
Servo
motor
OPMode
Speed scale
denominator/
numerator
(0x2011/0x2010)
Position scale
denominator/
numerator
(0x200F/0x200E)
Enco
der
Velocity actual value (0x606C)
Position actual value
(0x6064)
Torque actual value (0x6077)
FollowingError
and
Positionreached
1
2
2
Speed
calculation
Position
calculation
Position actual internal value
(0x6063)

(0x6064)
Outputofposition
limitfunction
-
+
window
comparator
Position
window time
(0x6068)
Position window
(0x6067)
TargetReachedin
Statusword
(0x6041.10)
`
PositionReached
Position demand
internal value
(0x60FC)
Position scale
denominator/
numerator
(0x200F/0x200E)
Position actual
value
(0x6064)
-
+
window
comparator
Following error
time out
(0x6066)
Following error window (0x6065)
FollowingError
InStatus
word(0x6041.13)
Following error actual
value (0x60F4)
FollowingError
1
2
2
Position
demand
value
(0x6062)

6-6
Related Objects
Index Sub Name
Data
Type
Access
PDO
Mapping
Units
0x607A - Target position DINT RW Yes
Pos
Units
0x607D
- Software position limit - - - -
0 Number of entries USINT RO No -
1 Minimum position limit DINT RW No
Pos
Units
2 Maximum position limit DINT RW No
Pos
Units
0x607F - Maximum profile velocity UDINT RW No
Vel
Units
0x6081 - Profile velocity UDINT RW Yes
Vel
Units
0x6083 - Profile acceleration UDINT RW Yes
Acc
units
0x6084 - Profile deceleration UDINT RW Yes
Acc
units
0x6085 - Quick Stop deceleration UDINT RW Yes
Acc
units
You can use the following three position commands in Profile Position Mode:
Single set point
After reaching the target position, the drive sends a completion signal to the master and receives a
new command.
Change immediately
After receiving a new position command while driving to the target position, it drives to the new
position regardless of the existing target.
Set of Set point
After receiving a new position command while driving to the target position, it subsequently drives
to the new target after reaching the existing target. This mode retains the previous velocity.
The two methods mentioned above are controlled by the New setpoint bit (Controlword,
0x6040.4), the Change set immediately bit (Controlword, 0x6040.5), and the Change
setpoint bit (Controlword, 0x6040.9).

6-7
The single setpoint procedure

1. Specify the target position (0x607A).
2. Set the New setpoint bit to 1 and the Change set immediately bit to 0 to request the position
operation.
3. The drive notifies the operator of its arrival at the target position with the Target reached bit
(Statusword, 0x6041.10). The drive can stay where it is or perform a new position operation if it
receives the New set point bit.
The change immediately procedure

2. Set the New setpoint bit to 1 and the Change set immediately bit to 1 to request the position
operation.
3. You can begin a new position operation (New setpoint) regardless of the previous target position.
4. The drive immediately moves to the new position.
(Statusword, 0x6041.10).

6-8
The set of set point procedure

2. Set the New setpoint bit to 1 and the Change of Set point bit to 1 to request the position operation.
3. After reaching the previous target position, the drive begins to move to the new position (New
setpoint). The drive retains the previous velocity.
(Statusword, 0x6041.10).

6-9
6.3.2 Interpolated Position Mode
Interpolated Position Mode controls multiple axes or a single axis. This mode necessitates
time interpolation of the Set point. It can adjust the time of any drive unit associated via the
time sync technology.
The interpolation cycle is defined by 0x60C2, and the interpolation data can be entered via
0x60C1.
The Interpolated Position Mode diagram

Position
controller
Speed
controller
Torque
controller
Servo
motor
OPMode
Speed scale
denominator/
numerator
(0x2011/0x2010)
Position scale
denominator/
numerator
(0x200F/0x200E)
Enco
der
(0x6064)
FollowingError
and
Positionreached
1
2
2
Speed
calculation
Position
calculation
(0x6063)

(0x6064)
Outputofposition
limitfunction
-
+
window
comparator
Position
window time
(0x6068)
Position window
(0x6067)
TargetReachedin
Statusword
(0x6041.10)
`
PositionReached
Position
demand
internal value
(0x60FC)
Position scale
denominator/
numerator
(0x200F/0x200E)
Position actual
value
(0x6064)
-
+
window
comparator
Following error
time out
(0x6066)
Following error window
(0x6065)
FollowingError
InStatus
word(0x6041.13)
Following error actual value
(0x60F4)
FollowingError
1
2
2
Position
demand value
(0x6062)

6-10
Related Objects
Index Sub Name
Data
Type
Access
PDO
Mapping
Units
0x60C1 1 Interpolation data record DINT RW Yes
Pos
Units
0x607D
Pos
Units
Pos
Units
Acc
units
Acc
units
0x60C2
-
Interpolation cycle
(Interpolation Time Period)
- - - -
1
Interpolation cycle
(Interpolation time period)
USINT RW No -
2 Interpolation time index SINT RW No -

6-11
6.3.3 Cyclic Synchronous Position Mode
Cyclic Synchronous Position Mode drives the L7N by receiving updated target positions
(0x607A) with each POD update cycle from the master. You can use this mode to drive the
L7N by adding a torque offset (0x60B2) and speed offset (0x60B1).
The Cyclic Synchronous Position Mode diagram
OPMode:CyclicSyncronousPosition
Velocity offset (0x60B1)
Target position (0x607A)
Software position limit (0x607D)
(or profile deceleration (0x6084))
Quick Stop option code (0x605A)/
Halt option code (0x605D)
Position scale
(0x200E/0x200F)
Acceleration/
deceleration scale
(0x2012/0x2013)
Position
trajectory
generator
Position
demand internal
value
(0x60FC)
denominator
(0x2010/0x2011)
Torque offset (0x60B2)
[Posunit]
[Velunit]
[Accunit] [pulse/s
2
]
[pulse/s]
1
2
3
[pulse]

Position
controller
Speed
controller
Torque
controller
Servo
motor
OPMode
Speed scale
denominator/
numerator
(0x2011/0x2010)
Position scale
denominator/
numerator
(0x200F/0x200E)
Enco
der
(0x6064)
FollowingError
3
4
4
+
+
+
+
1 2
Velocity offset
(0x60B1)
Speed
calculation
Position
calculation
Position actual internal
value (0x6063)

Position demand
internal value
(0x60FC) Position scale
denominator/
numerator
(0x200F/0x200E)
Position actual
value
(0x6064)
-
+
window
comparator
Following error
time out
(0x6066)
Following error window (0x6065)
FollowingError
InStatus
word(0x6041.13)
Following error actual value
(0x60F4)
3
4
Position
demand value
(0x6062)
FollowingError

6-12
Related Objects
Index Sub Name
Data
Type
Access
PDO
Mapping
Units
0x607A - Target position DINT RW Yes
Pos
Units
0x607D
Pos
Units
Pos
Units
Acc
units
0x6085 - Quick Stop deceleratio UDINT RW Yes
Acc
units
0x60B1 - Velocity offset DINT RW Yes
Vel
units
0x60B2 - Torque offset INT RW Yes 0.1%

6-13
6.4 Homing
The following figure outlines the homing inputs and outputs. You can specify the speed,
acceleration and homing method. The Home offset allows you to input the origin of the use's
coordinate system in the Home, rather than its initial origin.
Homing
method
Controlword(0x6040)
Homing Method (0x6098)
Homing speed (0x6099)
Homing acceleration (0x609A)
Home offset (0x607C)
Statusword(0x6041)
Position demand internal value (0x60FC)
or position demand value (0x6062)
DigitalInput
Homeswitch
Positivelimitswitch
Negativelimitswitch

Related Objects
Index Sub Name
Data
Type
Access
PDO
Mapping
Units
0x607C - Home Offset DINT RW No Pos Units
0x6098 - Homing Method SINT RW Yes -
0x6099
- Homing Velocity - - - -
1
Switch search speed
(Speed during search for switch)
UDINT RW Yes Vel Units
2
Zero search speed
(Speed during search for zero)
UDINT RW Yes Vel Units
0x607D
-
Software position limit
(Software Position Limit)
- - - -
1 Minimum position limit (Min. position limit) DINT RW No Pos Units
2 Maximum position limit (Max. position limit) DINT RW No Pos Units
0x609A - Homing Acceleration UDINT RW Yes Acc Units
0x200D -
Basic function setting (Function Select
Switch)
UINT RW No -
0x200E -
Position scale numerator
(Position Scale Numerator)
INT RW No -
0x200F -
Position scale denominator
(Position Scale Denominator)
INT RW No -
6-14
Homing Method (0x6098)
Value Details
0 No Homing
1, 2
(1) If the NOT switch is OFF, then the initial direction of rotation is CW. The direction
is diverted if the NOT switch is ON. After the NOT switch is turned on, the position
that the first index pulse encounters while driving in the CCW direction becomes the
Home position.
(2) If the POT switch is OFF, then the initial direction of rotation is CCW. The direction
is diverted if the POT switch is ON. After the POT switch is turned on, the position
that the first index pulse encounters while driving in the CW direction becomes the
Home position.

7 to 10
The methods described for 7 to 10 determine the Home position using the Home
switch and the POT switch.
(7) Upper figure: If the POT switch is OFF, then the drive operates at switch search
speed and the initial direction of rotation is CCW. The direction is diverted if the
Home switch is ON. After the Home switch is turned on, the position that the first
index pulse encounters while driving in the CW direction becomes the Home position,
and it drives at zero search speed.
(7) Middle figure: If the POT switch is OFF and the Home switch is ON, then the drive
operates at switch search speed and the initial direction of rotation is CW. If the
Home switch is turned off at this time, it transfers to zero search speed. After the
Home switch is turned off, the position that the first index pulse encounters while
driving in the CW direction becomes the Home position.
(7) Lower figure: If the POT switch is OFF and the Home switch is ON, then the drive
operates at switch search speed and the initial direction of rotation is CCW. The
direction is diverted if the POT switch is ON. If the Home switch is turned from ON to
OFF at this time, it drives at zero search speed, and the position that the first index
pulse encounters while driving in the CW direction becomes the Home position.
The methods from 8 to 10 are identical to the methods for 7 in terms of how they
determine the Home position. The only differences are the initial driving direction and
Home switch polarity. Refer to the following figure.

6-15
Value Details
11 to 14
The methods described for 11 to 14 determine the Home position using the Home
switch and the NOT switch.
(11) Upper figure: If the NOT switch is OFF, then the drive operates at switch search
speed and rotates CW. If the Home switch is turned on at this time, it changes the
direction of rotation, and the position that the first index pulse encounters while
driving CCW at zero search speed becomes the Home position.
(11) Middle figure: If the NOT switch is OFF and the Home switch is ON, then the
drive operates at switch search speed and rotates CCW. If the Home switch is turned
off at this time, it transfers to zero search speed. After the Home switch is turned off,
the position that the first index pulse encounters while driving in the CCW direction
becomes the Home position.
(11) Lower figure: If the NOT switch is OFF, then the drive operates at switch
search speed and rotates CW. If the NOT switch is turned on at this time, it changes
the direction and continues to drive CCW at switch search speed. If the Home switch
is then changed from ON to OFF, then it transfers to zero search speed, and the
position that the first index pulse encounters becomes the Home position.
The methods from 12 to 14 are identical to the methods for 11 in terms of how they
determine the Home position. The only differences are the initial driving direction and
Home switch polarity. Refer to the following figure.
24
It determines the Home position in the same manner as method 8, but it does not use
an index pulse. The point where the Home switch is turned on or off becomes the
Home position.

6-16
Value Details
28
It determines the Home position in the same manner as method 12, but it does not
use an index pulse. The point, where the Home switch is turned on or off, becomes
the Home position.

33, 34
The position that the first index pulse encounters while driving in a CCW/CW
direction becomes the Home position.

35 The starting point of the homing operation becomes the Home position.
Note) : Switch search speed (0x6099:01) : Zero search speed
(0x6099:02) :

6-17
6.5 Velocity Control Mode
6.5.1 Profile Velocity Mode
In Profile Velocity Mode, the L7N accelerates to the target velocity (0x60FF) at the profile
acceleration speed (0x6083) and decelerates at the profile deceleration speed (0x6084). The
max. profile velocity limits the maximum velocity (0x607F).
The Profile Velocity Mode block diagram
OPMode:ProfileVelocity
Target velocity
(0x60FF)
Max. profile velocity (0x607F)
Profile acceleration (0x6083)
Profile deceleration (0x6084)
denominator
(0x2010/0x2011)
Acceleration/
deceleration scale
(0x2012/0x2013)
[Velunit]
[Accunit]
Velocity
trajectory
generator
Required velocity
value
(0x606B)
[pulse/s]
[pulse/s
2
]
1

Speed
controller
Torque
controller
Servo
motor
Speed scale
denominator/
numerator
(0x2011/0x2010)
Position scale
denominator/
numerator
(0x200F/0x200E)
Enco
der
(0x6064)
Velocityreached
1
Speed
calculation
Position
calculation
OPMode
2
(0x6063)

Velocity actual value
(0x606C)
Outputofvelocity
limitfunction
-
+
window
comparator
Velocity window
time
(0x606E)
Velocity window
(0x606D)
TargetReachedin
Statusword
(0x6041.10)
VelocityReached
2

6-18
Related Objects
Index Sub Name
Data
Type
Access
PDO
Mapping
Units
0x60FF - Target velocity DNIT RW Yes
Vel
Units
0x607F - Maximum profile velocity UDINT RW Yes
Vel
Units
0x6083 - Profile acceleration) UDINT RW Yes
Acc
units
Acc
units
0x6085 - Quick UDINT RW Yes
Acc
units
0x606B -
Required velocity value
(Velocity Demand Value)
DINT RO Yes
Vel
Units
0x606C -
Actual velocity value
(Velocity Actual Value)
DINT RO Yes
Vel
Units
0x606D -
Velocity span
(Velocity Window)
UINT RW No
Vel
Units
0x606E -
Time to reach the target velocity
(Velocity Window Time)
UINT RW No ms

6-19
6.5.2 Cyclic Synchronous Velocity Mode
In Cyclic Synchronous Velocity Mode, the master orders the target velocity (0x60FF) for the
drive and performs velocity control. This mode allows you to add the torque offset (0x60B2)
to the master.
The Cyclic Synchronous Velocity Mode block diagram
OPMode:CyclicSyncronousVelocity
Velocity offset (0x60B1)
Target velocity (0x60FF)
(or profile deceleration (0x6084))
denominator
(0x2010/0x2011)
Acceleration/
deceleration scale
(0x2012/0x2013)
Velocity
trajectory
generator
Required
velocity value
(0x606B)
+
+ [Velunit] [pulse/s]
[pulse/s
2
]
2
1

Speed
controller
Torque
controller
Servo
motor
Speed scale
denominator/
numerator
(0x2011/0x2010)
Position scale
denominator/
numerator
(0x200F/0x200E)
Enco
der
(0x6064)
Velocityreached
2
Speed
calculation
Position
calculation
3
+
+
1
OPMode
Torque offset
(0x60B2)
(0x6063)

Actual velocity value
(0x606C)
Outputofvelocity
limitfunction
-
+
window
comparator
Velocity
window time
(0x606E)
Velocity window
(0x606D)
TargetReachedin
Statusword
(0x6041.10)
VelocityReached
3

6-20
Related Objects
Index Sub Name
Data
Type
Access
PDO
Mapping
Units
0x60FF - Target velocity DNIT RW Yes
Vel
Units
0x60B1 - Velocity offset DINT RW Yes Vel units
Acc
units
Acc
units
0x606B - Required velocity value DINT RO Yes
Vel
Units
0x606C - Actual velocity valu DINT RO Yes
Vel
Units
0x606D - Velocity span UINT RW No
Vel
Units
0x606E -
Time to reach the target
velocity
UINT RW No ms

6-21
6.6 Torque Control Modes
6.6.1 Profile Torque Mode
In Profile Torque Mode, the drive torque increases or decreases at the rate of the torque
gradient (0x6087) up to the target torque (0x6071). The forward/reverse torque limit value
(0x60E0, 0x60E1) limits the torque. The max. torque (0x6072) value indicates the maximum
torque that can be applied to the motor regardless of the forward/reverse direction.
The Profile Torque Mode block diagram
OPMode:ProfileTorque
Target torque (0x6071)
Torque slope (0x6087)
Torque
trajectory
generator
Max. torque (0x6072)
Required
torque value
(0x6074)
Positive/negative torque limit value (0x60E0/
0x60E1)
1

Torque
controller
Servo
motor
Speed scale
denominator/
numerator
(0x2011/0x2010)
Position scale
denominator/
numerator
(0x200F/0x200E)
Enco
der
(0x6064)
1
Speed
calculation
Position
calculation
OPMode
(0x6063)

6-22
Related Objects
Index Sub Name
Data
Type
Access
PDO
Mapping
Units
0x6071 - Target torque INT RW Yes 0.1%
0x6087 - Torque gradient UDINT RW Yes 0.1%/s
0x6074 - Required torque value INT RO Yes 0.1%
0x6077 -
Actual torque value

INT RO Yes 0.1%
0x6072 - Max. torque UINT RW Yes 0.1%
0x60E0 -
Forward torque limit value
(Positive Torque Limit Value)
UINT RW Yes 0.1%
0x60E1 -
Reverse torque limit value
(Negative Torque Limit Value)
UINT RW Yes 0.1%

6-23
6.6.2 Cyclic Synchronous Torque Mode
In Cyclic Synchronous Torque Mode, the master orders the target torque (0x6071) for the
drive and performs torque control.
The Cyclic Synchronous Torque Mode block diagram
Torque
trajectory
generator
Max. torque (0x6072)
Positive/negative torque limit value (0x60E0/
0x60E1)
Target torque (0x6071)
+
+ [Velunit]
OPMode:CyclicSyncronousTorque
Required
torque value
(0x6074)
1

Torque
controller
Servo
motor
Speed scale
denominator/
numerator
(0x2011/0x2010)
Position scale
denominator/
numerator
(0x200F/0x200E)
Enco
der
(0x6064)
1
Speed
calculation
Position
calculation
OPMode
(0x6063)

6-24
Related Objects
Index Sub Name
Data
Type
Access
PDO
Mapping
Units
0x6071 - Target torque INT RW Yes 0.1%
0x6074 - Required torque value INT RO Yes 0.1%
0x6077 - Actual torque value INT RO Yes 0.1%
0x6072 - Max. torque UINT RW Yes 0.1%
0x60E0 -
UINT RW Yes 0.1%
0x60E1 -
UINT RW Yes 0.1%

6-25
6.7 The Torque Limit Function
The minimum torque limit value (between the forward (0x60E0), reverse (0x60E1) and max.
torque (0x6072)) determines the torque limit.
The Torque Limit Function block diagram

Related Objects
Index Sub Name
Data
Type
Access
PDO
Mapping
Units
0x6072 -
Max. torque
(Max. Torque)
UINT RW Yes 0.1%
0x60E0 -
UINT RW Yes 0.1%
0x60E1 -
UINT RW Yes 0.1%

6-26
6.8 Digital Input/Output
Digital input/output controls the input/output signal of the CN1 connector on the L7N.
For more information, refer to 7.6 0x60FD (Digital Input) and 0x60FE (Digital Output) of the
CiA402 Objects.
Related Objects
Index Sub Name Data Type Access PDO Mapping Units
0x60FD -
Digital input
(Digital Inputs)
UDINT RO Yes -
0x60FE
-
Digital output
(Digital Outputs)
- - - -
0
Number of entries
(Number of entries)
USINT RO No -
1
Physical output
(Physical outputs)
UDINT RW Yes -
2
Bit mask
(Bit mask)
UDINT RW No -

6-27
6.9 Touch Probe Function

Position feedback is latched to the following trigger events:
Touch probe 1 (CN1, PROBE1 (pin 9))
Touch probe 2 (CN1, PROBE2 (pin 10))
The encoder index pulse
You can use the following two touch probe functions simultaneously:
Touch probe 1 latch function (For more information, see
Section 6.5)
Bits related to latch control: 0x60B8.0~7
Bits related to latch status: 0x60B9.0~7
Position value of the rising edge of touch probe 1: 0x60BA
Position value of the falling edge of touch probe 1: 0x60BB
Trigger signal: Encoder Z signal/probe 1 signal
Touch probe 2 latch function (For more information, see
Section 6.5)
Bits related to latch control: 0x60B8.8~15
Bits related to latch status: 0x60B9.8~15
Position value of the rising edge of touch probe 2: 0x60BC
Position value of the falling edge of touch probe 2: 0x60BD
Trigger signal: Probe 2 signal

Touch
Probe
Function
(0x60B8)

1
2
1 (0x60BB)
2 (0x60BC)
2 (0x60BD)
1 (0x60BA)
(0x60B9)
Touch Probe Function (0x60B8)
Digital input
Touch probe 1
Touch probe 2
Position value of the falling edge of
touch probe 2 (0x60BB)
Touch probe state (0x60B9)
Position value of the rising edge of
6-28
Related Objects
Index Sub Name
Data
Type
Access
PDO
Mapping
Units
0x60B8 - Touch probe function UINT RW Yes -
0x60B9 - Touch probe status UINT RO Yes -
0x60BA -
touch probe 1
(Touch Probe 1 Positive Edge
Position Value)
DINT RO Yes
Pos
units
0x60BB -
touch probe 1
(Touch Probe 1 Negative Edge
Position Value)
DINT RO Yes
Pos
units
0x60BC -
touch probe 2
(Touch Probe 1 Positive Edge
Position Value)
DINT RO Yes
Pos
units
0x60BD -
touch probe 2
(Touch Probe 1 Negative Edge
Position Value)
DINT RO Yes
Pos
units

6-29
Touch Probe Timing Diagrams
Single Trigger Mode (0x60B8.1=0, 0x60B8.9=0)
0x60B8.0
(0x60B8.8)
0x60B8.4
(0x60B8.12)
0x60B9.0
(0x60B9.8)
Probe input
0x60B9.1
(0x60B9.9)
0x60BA
(0x60BC)
Latched position 1
Latched position 3
Latch start Latch start
1 2 3

Continuous Trigger Mode ((0x60B8.1=0, 0x60B8.9=0)
0x60B8.0
(0x60B8.8)
0x60B8.4
(0x60B8.12)
0x60B9.0
(0x60B9.8)
Probe input
0x60B9.1
(0x60B9.9)
0x60BA
(0x60BC)
Latched position 1 Latched position 3
Latch start
1 2 3
0x60B9.7
(0x60B9.15)
Latched position 2

6-30

Z-Phase signal Trigger mode (60B8h bit2 = 1, or bit10 = 1)

5. L7 Drive Setup
7-1
7. L7 Drive Setup
7.1 Setting System Parameters
1. The motor ID setting [0x2000]
Serial encoder: Reads the motor ID from the encoder and configures it.
2. Encoder settings
When connecting a single-turn type encoders motor, it is automatically set motorID(0x2000), encoder
pulse(0x2002)value. In case of Multiturn serial encoder, Set the encorder type.
Encoder type [0x2001]
Number Encoder Type Number Encoder Type
1 Singleturn serial encoder 1 Multiturn serial encoder
Encoder pulse [0x2002]
Indicates the pulses per revolution in a bit for the encoder type (2
n(bit)
).
3. Main power input mode [0x2003]
Specifies the main power input mode and the processing mode if phase loss occurs. You can
specify the handling methods for three-phase and single-phase power inputs and the power phase
loss (Refer to section 7.5).
4. The main power phase loss monitoring interval [0x2004]
Specifies the monitoring interval for main power phase losses.
5. The 7SEG display object setting [0x2005]
Specifies the objects applied when the servo turns on.
The setting values range from [0x2600] to [0x2616]. Choose a number from 2600-2616 and use
that number to set the corresponding parameter. . You can display the number and value of the
variable every time you press the panel operator switch. For 32-bit variables, press and hold the
switch to indicate the upper/middle/lower locations in 4 figures.
6. The regenerative overload derating factor [0x2006]
This specifies the derating factor which checks for regenerative resistance overloads. If the derating
value is 100% or less, then the overload alarm trigger time is proportional to the set value.
7. The regenerative resistance value [0x2007]
This specifies the resistance value for regenerative braking resistance. If it is set to 0, then it uses
the default resistance capacity embedded in the drive.

7. L7 Drive Setup
7-2
8. The regenerative resistance capacity [0x2008]
This specifies the current capacity for regenerative resistance. If it is set to 0, then it uses the
default resistance capacity embedded in the drive.
9. The overload check default load factor [0x2009]
This indicates the load factor which triggers a continuous overload check. If it is set to 100 or less,
then the overload check starts early and the overload alarm triggers early.

10. The overload warning level [0x200A]
This specifies the level for the continuous overload warning signal output. The warning signal is
issued when it reaches the setting of the percentage value relative to the alarm trigger value.

5. L7 Drive Setup
7-3

11. The PWM Off delay time [0x200B]
This specifies the time span between the servo Off command and actual PWM Off. This prevents
the motor from slipping down the vertical axis while the servo Off command and brake command
order the motor brake to engage. Use a PWM off delay when operating a motor brake through the
output contact point brake signal. (range: 0-1000 ms, initial value: 10).

12. The DB control mode [0x200C]: Specifies the DB control mode. You can use the following four
modes: (Refer to section 7.5)
Mode Operation type
Hold after a DB stop

Release after a DB
stop

Release after a free
run stop

Hold after a free run
stop

13. The basic servo function setting bit [0x200D]: Specifies the drive function. You can set it to move
forward, in reverse or to operate the servo lock function. (refer to section 8.5).

7. L7 Drive Setup
7-4

7.2 Configuring Control Parameters
The control parameter setting sequence is as follows:
Load the inertia ratio [0x2100] setting.
Adjust the proportional gain with [0x2101] and [0x2102].
Increase the gain so that the servo motor does not overshoot or lose control (do not use during
speed operations or torque operations).
Adjust the speed proportional gain with [0x2106] and [0x2107].
Increase the gain so that the servo motor does not vibrate.
Adjust the speed integral time constant with [0x2108] and [0x2109].
Refer to the following table and set it according to the speed proportional gain.
7.2.1 The Inertia Ratio Setting [0x2100]
This sets the inertia ratio by calculating the load inertia from the machine system and rotor
inertia listed on the motor specification table.
Inertia ratio = load inertia / motor rotor inertia x 100
The inertia/load ratio is an important control parameter for the operation of the servo. It is
crucial to set the correct inertia ratio for optimal servo operation.
The following table outlines the recommended control gain for different inertia ratios:
Motor
Flange
Inertia ratio Gain Range
Categor
y
Inertia
(Multiple)
Position
Proportional
Gain
Speed
Proportional
Gain
Speed Integral
Gain
40
~ 80
Low
inertia
1 ~ 5 40 ~ 90 400 ~ 1000 10 ~ 40
Medium
inertia
5 ~ 20 20 ~ 70 200 ~ 500 20 ~ 60
High
inertia
20 ~ 50 10 ~ 40 100 ~ 300 50 ~ 100
* You can tune the inertia ratio during a test drive if it is too hard to calculate the inertia ratio
before operation.

5. L7 Drive Setup
7-5
7.2.2 The Position Control Gain

Position command: Counts the position command pulses entering from outside and converts them
into position commands. It uses them as internal position commands after initial filtering.
Current position: Counts the pulse signals received from the encoder and uses the electronic gear
ratio settings to convert them to the current position.
Position proportional gain [0x2101] and [0x2102]: Converts the difference between the position
command and the current position into a speed command by multiplying it by the position
proportional gain.
Recommended value = speed proportional gain [0x2106] / 10
Feed-forward gain [0x2104]: Uses the differences in value to the position command to calculate
the gradient. Adds the speed command to the gradient to reduce the time needed to reach the
target position. If the value which results is too large, then the position controller may overshoot or
become unstable. It is important to gradually increase the value from a small value while monitoring
the test drive.
Feed-forward filter [0x2105]: The feed-forward control filter vibrates if the position command
changes too drastically. If this occurs, configure the filter value until the vibrations disappear.

7. L7 Drive Setup
7-6
7.2.3 The Speed Control Gain

Speed command: Operates the speed command through the speed command filter [0x210A].
Current speed: Calculates the speed by counting the number of encoder signals as time
progresses. Filters the speed to calculate the current speed. The algorithm uses the current
torque and inertia to project the speed and compensate for errors which occur when calculating the
speed at very low speeds. Therefore, an accurate motor constant and inertia ratio are closely
related to the stability of the motor speed control.
Speed integral time constant [0x2108]: Calculates the integral value of the speed error. The
speed error is the difference between the command speed and the current speed. The speed
integral time constant converts the speed error into a torque command by multiplying it by the
integral time constant.
A decreased integral time constant solves transient response issues and improves speed tracking.
If the integral time constant is too small, however, an overshoot occurs. On the other hand, if the
integral time constant is too large, an excessive response drop occurs and proportional control
takes over.
Recommended value = 10000/speed proportional gain [0x2106]

Speed
Time
Command speed
Tracking speed
Low
High
5. L7 Drive Setup
7-7
Speed proportional gain [0x2106]: Converts the speed error into a torque command by
multiplying it by the proportional gain.
If the resulting value is large, then the speed response accelerates and speed tracking increases.
However, vibrations occur if the value is too large. If the value is too small, then speed response
slows down and speed tracking decreases. This may cause the servo to lose power.

Speed feedback filter time constant [0x210B]: Filters the speed feedback to control vibrations
when the speed of the motor changes due to drive system vibrations or vibrations due to gain and
too much load inertia. If the value is too high, it reduces speed responsiveness and control power
may be compromised.
Recommended value = 0 to speed integral time constant [0x2108]/10
7.2.4 The Torque Command Filter Time Constant
Time [0x210C]
Use a digital filter for the analog torque command voltage to improve the stability of
command signals. If the filter value is set too high, responsiveness to torque commands will
be reduced. It is important to set an appropriate value for your system.
7.2.5 Gain 1 Gain 2 Transfer Mode [0x210D]
Set the gain transfer mode. You can set the transfer method with the zero speed conditions,
position reached status, contact input status, etc. (refer to section 8.5).
7.2.6 Gain 1 Gain 2 Transfer Time [0x210E]
Configure the gain transfer time during operation.
When converting gain 1 to gain 2 or gain 2 to gain 1, the conversion occurs according to the
set time.
7.2.7 P/PI Transfer Mode [0x210D]
Configure the P and PI transfer modes. You can configure the set conditions, set speed, set
acceleration, set position error, etc. for the transfer method (refer to section 7.5 ).
Time
Speed
Command speed
High
Low
7. L7 Drive Setup
7-8
7.2.8 Resonance Avoidance Operations [0x210F],
[0x2110], [0x2111]

Mechanical resonance causes vibrations to occur at certain frequencies in certain systems.
You can control the vibrations by controlling the torque output for specific frequencies.
The resonance avoidance operation [0x210F] (refer to section 8.5).

Resonance avoidance frequency [0x2110]
Torque output
Torque output frequency
Resonance avoidance range
BW [0x2111]
5. L7 Drive Setup
7-9
7.3 Setting the Input/Output Contact Point
Parameters
There are 6 points for digital inputs (totaling 8 functions): + PROBE1, PROBE2
: PCON, GAIN2, ALMRST, HOME, P-OT, N-OT
There are 4 points for digital outputs (totaling 7 functions):
: ALARM, READY, ZSPD, BRAKE, INPOS, INSPD, WARN
You can assign input/output signals by parameter and set the input/output contact logic (A/B
contacts).
: Input signal definition (0x2200, 0x2201)
: Output signal definition (0x2202, 0x2203)
: Input signal logic setting (0x2204)
: Output signal setting (0x2205)
For PROBE1 (CN1-9)/PROBE2 (CN1-10), the pins are assigned separately and interrupted for the
inputs.
Basic settings for input signal definitions
Object
Input
Signal
CN1 Pin Default Allocation Number Default
Setting
Value
Index Bit DI#6(7) DI#5(8) DI#4(14) DI#3(12) DI#2(14) DI#1(13)
0x2200 0 to 3
PCON 6 5 4 3 2 1
0x4000
0x2200 4 to 7
GAIN2 6 5 4 3 2 1
0x2200 8 to11
A-RST 6 5 4 3 2 1
0x2200 12 to 15
HOME 6 5 4 3 2 1
0x2201 0 to 3
P-OT 6 5 4 3 2 1
0x0065
0x2201 4 to 7
N-OT 6 5 4 3 2 1

7. L7 Drive Setup
7-10
Logic definitions for input signals (0x2204)- logic settings for DI#1 to DI#6 by bit.
Bit function
Value
(Hex)
Setting details
0 DI#1 input logic setting
0 Contact B
1 Contact A
Note 1)

0 Contact B
1 Contact A
Note 1)

0 Contact B
1 Contact A
Note 1)

0 Contact B
1 Contact A
Note 1)

0 Contact B
1 Contact A
Note 1)

0 Contact B
1 Contact A
Note 1)

Note 1) The default setting value.
Basic settings for the output signal definitions
Object
output
signal
CN1 Pin Default Allocation Number Default
Setting
Value
Index Bit DO#4
(1,2)
DO#3
(19,20)
DO#2
(17,18)
DO#1
(3,4)
0x2202 0 to 3
ALARM 4 3 2 1
0x4321
0x2202 4 to 7
READY 4 3 2 1
0x2202 8 to11 ZSPD 4 3 2 1
0x2202 12 to 15
BRAKE 4 3 2 1
0x2203 0 to 3 INPOS 4 3 2 1
0x0000
0x2203 4 to 7 INSPD 4 3 2 1
0x2203 8 to11 WARN 4 3 2 1
0x2203 12 to 15 RESERVED 4 3 2 1
Logic definitions for output signals (0x2205)- output logic settings for D0#1 to DO#4 by bit
Bit function
Value
(Hex)
Setting details
0 DO#1 input logic setting
0 Contact B
Note 1)

1 Contact A.
0 Contact B
1 Contact A
Note 1)

0 Contact B
1 Contact A
Note 1)

0 Contact B
Note 1)

1 Contact A

Note 1) The default setting value.
5. L7 Drive Setup
7-11
7.4 Setting Speed Operation Parameters
7.4.1 Acceleration/Deceleration Time
Acceleration time [0x2301]: Specifies the time required, in ms, for the motor to reach the rated
motor speed from zero speed.
Deceleration time [0x2302]: Specifies the time, in ms, required for the motor to stop after running at
the rated motor speed.
7.4.2 The S-Curve Operation [0x2304]
You can configure the acceleration/deceleration operation in an S-curve pattern for smooth
acceleration/deceleration.
0: Trapezoidal -> Configure the acceleration/deceleration time in [0x2301] and [0x2302].
1: Sinusoidal -> Configure the acceleration/deceleration time in [0x2301] and [0x2302] + S-curve
time in [0x2303].
7.4.3 The Manual JOG Operation Speed [0x2305]
Drive the forward/reverse rotation at the JOG operation speed. This ignores the CN1 contact
point input status.
7.5 Setting Position Operation Parameters
7.5.1 Backlash Compensation [0x2403]
If the position operation causes backlashes which change the position, then this setting
converts backlash amount into a number of pulses to compensate for the backlash.

7. L7 Drive Setup
7-12
7.6 Setting Parameters for L7N Built-in
Functions
Configure the default parameters that the L7N provides.
7.6.1 Checking/Deleting the Alarm History [0x2700]
You can check and delete the alarm history.
Delete the Alarm History [0x2700:1]
This allows you to delete the alarm history.
Check the Alarm History [0x2700:2 to 21]
This allows you to check the last 20 alarm history items in sequence (the most recent appear first).
7.6.2 Auto Gain Tuning [0x2701]
Start Auto Gain Tuning [0x2701:1]
Starts auto gain tuning.
Auto Gain Tuning Speed [0x2701:2]
Specifies the auto gain tuning speed in 100 RPM increments.
Auto Gain Tuning Distance [0x2701:3]
Specifies the auto gain tuning distance.
7.6.3 Absolute Encoder Reset [0x2702]
Reset encoder [0x2702:1]
Type"rse" (72 73 65 74) to save the offset in the EEPROM inside the drive. The absolute encoder
resets after a few milliseconds.
When the absolute encoder reset is complete, the multi-turn data (0x260F) and single-turn data
(0x260D) resets to 0.
Check whether the actual position value (0x6064) becomes 0 to confirm the reset.
After resupplying power to the machine, read the absolute encoder position and apply the home
offset (0x607C) to display the actual position value (0x6064). At this time, the actual position value
(0x6064) does not change even if you change the home offset (0x607C) while driving.

8. Object Dictionary
8-1
8.1 The Object Dictionary List
The following table shows the Object Dictionary List.
Object Dictionaries Object Name
General Objects
0x1000 Device Type
0x1001 Error Register
0x1008 Manufacturer Device Name
0x1009 Hardware Version
0x100A Software Version
0x1010 Store Parameters
0x1011 Restore Default Parameters
0x1018 Identity Object
PDO Mapping Objects
0x1600
~ 0x1603
Receive PDO Mapping
0x1A00
~ 0x1A03
Transmit PDO Mapping
Sync Manager
Communication Objects
0x1C00 Sync Manager Communication Type
0x1C10
~ 0x1C13
Sync Manager PDO Assignment
0x1C32
~ 0x1C33
Sync Manager Synchronization
Manufacturer
Specific Objects
0x2000
~0x26FF
L7N Parameters
0x2000
~ 0x2013
Control Setting Parameter
0x200E
0x200F
Position User Unit
0x2010
0x2011
Velocity User Unit
0x2012
0x2013
Acceleration User Unit
0x2700
0x2701
Driving Operation Parameter
8-2
Device Control
0x603F Error Code
0x6040 Controlword
0x6041 Statusword
0x605A Quick Stop Option Code
0x605B Shutdown Option Code
0x605C Disable Operation Option Code
0x605D Halt Option Code
0x605E Fault Reaction Option Code
0x6060 Modes of Operation
0x6061 Modes of Operation Display
0x6502 Supported Drive Modes
0x607A Target Position
0x607D Software Position Limit
0x607F Max. Profile Velocity
0x6081 Profile Velocity
0x6083 Profile Acceleration
0x6084 Profile Deceleration
0x6085 Quick Stop Deceleration
Homing Mode
0x607C Home Offset
0x6098 Homing Method
0x6099 Homing Speeds
0x609A Homing Acceleration
Position Control Function
0x6062 Position Demand Value
0x6063 Position Actual Internal Value
0x6064 Position Actual Value
0x60FC Position Demand Internal Value
0x6065 Following Error Window
0x6066 Following Error Time Out
0x60F4 Following Error Actual Value
0x6067 Position Window
0x6068 Position Window Time
8-3
0x60C1 Interpolation Data Record
0x60C2 Interpolation Time Period
Cyclic Synchronous
Position Mode
0x60B1 Velocity Offset
0x60B2 Torque Offset
Profile Velocity/Cyclic
Synchronous Velocity Mode
0x606B Velocity Demand Value
0x606C Velocity Actual Value
0x606D Velocity Window
0x606E Velocity Window Time
0x60FF Target Velocity
Profile Torque/Cyclic
Synchronous Velocity Mode
0x6071 Target Torque
0x6074 Torque Demand Value
0x6087 Torque Slope
0x6076 Motor Rated Torque
0x6077 Torque Actual Value
Torque Limit Function
0x6072 Max. Torque
0x60E0 Positive Torque Limit Value
0x60E1 Negative Torque Limit Value
Touch Probe Function
0x60B8 Touch Probe Function
0x60B9 Touch Probe Status
0x60BA Touch Probe 1 Position Value
0x60BC Touch Probe 2 Position Value
Digital Inputs/Outputs
0x60FD Digital Inputs
0x60FE Digital Outputs

8-4
8.2 General Objects
0x1000, Device Type
The following table lists device types and their functions.
Index 0x1000 Device Type
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0x00020192- UDINT RO No - - -
Details

Additional information: 0x0002 (Servo drive)
Device profile number: 0x0192 (DS402)

0x1001, Error Register
The following table shows the error register values for each device. This value is stored in
the emergency message.
Index 0x1001 Error Register
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 USINT RO No - - -
Details
Bit function
Value
(Hex)
Setting details
0 General error
0 No error
1 Error
1 to 7 Reserved - 0 : Always

8-5

0x1008, Manufacturer Device Name
The following table shows the device model name.
Index 0x1008 Manufacturer Device Name
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 STRING RO No - - -

0x1009, Hardware Version
The following table shows the hardware version of the device.
Index 0x1009 Hardware Version
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x100A, Software Version
The following table shows the software version included with the device.
Index 0x100A Software Version
Sub
Index

Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit

8-6

0x1010, Store Parameters
The following table shows the parameter settings that you can store in the memory.
Index 0x1010 Store Parameters
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0x04 UDINT RW No 4 - -
Store all parameters
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0x0 UDINT RW No
0x00000000
to
0xFFFFFFF
F
- -
Store communication parameters
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2 0x0 UDINT RW No
0x00000000
to
0xFFFFFFF
F
- -
Store CiA402 parameters
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
3 0x0 UDINT RW No
0x00000000
to
0xFFFFFFF
F
- -
Store L7 specific parameters
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
4 0x0 UDINT RW No
0x00000000
to
0xFFFFFFF
- -
8-7
F
The L7N reads object entries to store parameters.
In order to prevent parameters from being incorrectly stored, the Sub-Index records a
specific"sav" when storing a parameter.

All parameters are stored when"sav" is written to Sub-Index 1.
Communications are stored when"sav" is written to Sub-Index 2.
CiA402 parameters are stored when"sav" is written to Sub-Index 3.
L7N parameters are stored when"sav" is written to Sub-Index 4.

8-8

0x1011, Restore Default Parameters
The following table shows the parameters you can reset.
Index 0x1010 Store Parameters
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0x04 UDINT RW No 4 - -
Restore default parameters
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0x0 UDINT RW No
0x00000000
to
0xFFFFFFF
F
- -
Restore communication default parameters
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2 0x0 UDINT RW No
0x00000000
to
0xFFFFFFF
F
- -
Restore CiA402 parameters
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
3 0x0 UDINT RW No
0x00000000
to
0xFFFFFFF
F
- -
Restore L7 Specific parameters
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
4 0x0 UDINT RW No
0x00000000
to
- -
8-9
0xFFFFFFF
F
The L7N reads object entries to reset parameters.
In order to prevent parameters from being incorrectly reset, the Sub-Index records"loa" when the
parameter is reset.

All parameters are reset when"loa" is written to Sub-Index 1.
Communication parameters are reset when"loa" is written to Sub-Index 2.
CiA402 parameters are reset when"loa" is written to Sub-Index 3.
L7N parameters are reset when"loa" is written to Sub-Index 4.
Turn the power off and then back on to restore the default values.

8-10

0x1018, Identity Object
The following table shows device information.

Index 0x1018 Identity Object
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Vendor ID
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0x00007595 UDINT RO No - - -
Product code
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2 0x0 UDINT RO No - - -
Revision number
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Serial number
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit

8-11
8.3 PDO Mapping Objects
You can map objects to Process Data Objects (PDO) when performing real-time data
transfers through the CANopen over the EtherCAT protocol.
These objects configure the incoming PDO mapping and outgoing PDO mapping.
Information about the mapped application object appears.

Bits 0-7: Bit lengths of mapped objects (ex.: 32-bit is displayed as 0x20)
Bits 8-15: Sub-Indexes of mapped objects
Bits 16-31: Indexes of mapped objects
0x1600 to 0x1603, Receive PDO Mapping

1s
t Receive PDO Mapping
Index 0x1600 1st Receive PDO Mapping
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 5 USINT RW No 0 to 8 - -
Mapping entry 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0x60400010 UDINT RW No
0 to
0xFFFFFFFF
- -
Mapping entry 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -
Mapping entry 3
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
3 0x607A0020 UDINT RW No
0 to
0xFFFFFFFF
- -

8-12

Mapping entry 4
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -
Mapping entry 5
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
5 0x60B80010 UDINT RW No
0 to
0xFFFFFFFF
- -

2n
d Receive PDO Mapping

Index 0x1601 2nd Receive PDO Mapping
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Mapping entry 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -
Mapping entry 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2 0x607A0020 UDINT RW No
0 to
0xFFFFFFFF
- -

8-13

3r
d Receive PDO Mapping
Index 0x1602 3rd Receive PDO Mapping
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting Range Change Unit
Mapping entry 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
0 to
0xFFFFFFFF
- -
Mapping entry 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
2 0x60FF0020 UDINT RW No
0 to
0xFFFFFFFF
- -

4t
h Receive PDO Mapping
Index 0x1603 4th Receive PDO Mapping
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Mapping entry 1
Sub
Index
Initial value
Data
Type
Access Initial value
Setting
Range
Change Unit
1 0x60400010 UDINT RW 0x60400010
0 to
0xFFFFFFFF
- -
Mapping entry 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -

8-14
0x1A00 to 0x1A03, Transmit PDO Mapping

1s
t Transmit PDO Mapping
Index 0x1A00 1st Transmit PDO Mapping
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 10 USINT RW No 0 to 10 - -
Mapping entry 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -
Mapping entry 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -
Mapping entry 3
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -
Mapping entry 4
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
4 0x60F40020 UDINT RW No
0 to
0xFFFFFFFF
- -
Mapping entry 5
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
5 0x60FD0020 UDINT RW No
0 to
0xFFFFFFFF
- -

8-15
Mapping entry 6
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -
Mapping entry 7
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -
Mapping entry 8
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFF
- -
Mapping entry 9
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
9 0x60B90010 UDINT RW No
0 to
0xFFFFFFF
-
Mapping entry 10
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
10 0x60BA0020 UDINT RW No
0 to
0xFFFFFFF
-

8-16

2n
d Transmit PDO Mapping

Index 0x1A01 2nd Transmit PDO Mapping
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Mapping entry 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -
Mapping entry 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -

3r
Index 0x1A02 3rd Transmit PDO Mapping
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Mapping entry 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -
Mapping entry 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -

8-17

4r
Index 0x1A03 4th Transmit PDO Mapping
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Mapping entry 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -
Mapping entry 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
0xFFFFFFFF
- -

8-18
8.4 Sync Manager Communication Objects
0x1C00, Sync Manager Communication Type
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Communication type sync manager 0
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1
1: mailbox receive
(Master to slave)
USINT RO No - - -
Sub
Index
Name
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2
2: mailbox send
(Slave to master)
USINT RO No - - -
Sub
Index
Name
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
3
3: process data
output
(Master to slave)
USINT RO No - - -
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
4
4: process data input
(Slave to master)
USINT RO No - -

8-19
0x1C10 to 0x1C13, Sync Manager PDO Assignment
This assigns the Sync Manager PDO when the PDO is transmitted through the data
communication process.

Index 0x1C10 Sync Manager 0 PDO Assignment
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit

Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit

Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Index of assigned RxPDO 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0x1601 UINT RW No
0x1600 to
0x1603
- -

8-20
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Index of assigned TxPDO 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0x1A01 UINT RW No
0x1A00 to
0x1A03
- -
You can change 0x1C12 and 0x1C13 in the EtherCAT Pre-Operational state.
Set Sub-Index 1 after Sub-Index 0 is registered as 0.

8-21
0x1C32, Sync Manager 2 Synchronization
Sync Manager 2 (Process Data Output) Synchronization

Index 0x1C32 Sync Manager 2 (Process Data Output) Synchronization
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0: Free-Run UINT RO No - -
Cycle time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2
Time between
Sync0 events [ns]
UDINT RO No - - -
Shift time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
3 125000 [ns] UDINT RO No - -
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
4
Bit 0 = 1
:Free-Run
supported
Bit 4:2 = 001
:DC Sync0
supported Bit 6:5 = 00
: No Output Shift
sup-ported
UINT RO No - - -
Minimum cycle time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
5 62500 [ns] UDINT RO No - -

8-22
Calc and copy time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
6 62500 [ns] UDINT RO No - - -
Delay time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
9 0 [ns] UDINT RO No - - -

Sync0 time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
10 same as 1C32:02 UDINT RO No - - -
Cycle exceeded counter
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
11 0 UDINT RO No - -
Shift too short counter
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
13 - UDINT RO No - - -
Sync error
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
32 - BOOL RO No - - -

8-23
0x1C33, Sync Manager 3 Synchronization
Sync Manager 3 (Process Data Input) Synchronization

Index 0x1C33 Sync Manager 3 (Process Data Intput) Synchronization
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 10 USINT RO No - -
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 same as 0x1C32:01 UINT RO No - -
Cycle time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Shift time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
3
125000*n [ns]
(n = 1, 2, 3...) Range:
0 to
(Sync0 event cycle
time 125000)
UDINT RO No - -
Synchronization
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
4
Bit 0 = 1
: Free-Run supported
Bit 4:2 = 001
: DC Sync0 supported
Bit 6:5 = 01
: Input Shift with local
timer supported

UINT RO No - -

8-24

Minimum cycle time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
5 same as 0x1C32:05 UDINT RO No - - -

Calc and copy time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
6 62500 UDINT RO No - - -
Delay time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
9 0 UDINT RO No - - -
Sync0 time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
SM event missed count
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Shift too short counter
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Sync error
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
14 - BOOL RO No - - -

8-25
8.5 Manufacturer Specific Objects
0x2000, Motor ID
This specifies the motor ID.
Index 0x2000 Motor ID
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 999 UINT RW No 0 to 999 PRECYC -

0x2001, Encoder Type
This specifies the current encoder type.

Index 0x2001 Encoder Type
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit

Value Encoder Type value Encoder Type
1 Single turn serial encoder 3 Mult iturn serial encoder

The encoder data is read to display the encoder type.

0x2002, Encoder Resolution
This specifies the encoder bits read for automatic display.

Index 0x2002 Encoder Resolution
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 19 UINT RW No 0 to 21 PRECYC [bit]

8-26
0x2003, Power Fail Mode
This specifies the main power input mode and the processing mode to use if phase loss
occurs.
Index 0x2003 Power Fail Mode
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0b000 UINT RW No
0b000
to 0b111
SV_OFF -
Details
Bit function
Value
(Hex)
Setting details
0
Set the main power input
type
0 Single-phase power input
1 Three-phase power input
1
How to handle phase loss on
the main power
0
Display Error in case of phase loss on the
main power.
1
Display Warning in case of phase loss on
the main power.
1 Use ADC.
Use DC.
0x2004, RST Power Fail Check Time
This specifies the monitoring interval when main power phase loss occurs.
Index 0x2004 RST Power Fail Check Time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 20 UINT RW No
0
to 5000
Always ms
0x2005, 7SEG Display Object
This specifies the 7SEG display objects.
Index 0x2005 7SEG Display Object
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RW Yes
2600
to 2616
Always -
Can specify the objects applied when the servo turns on.
There are 617 values available from Index 0x2600 to 0x2616. Choose one for the specific
parameter.

8-27
0x2006, Regenerative Resistor De-rating Factor
This specifies the derating factor which checks for regenerative resistance overloads. If the
derating value is 100% or less, then the overload alarm trigger time is proportional to the set
value.
Index 0x2006 Regenerative Resistor De-rating Factor
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 100 UINT RW No
0
to 200
SV_OFF [%]
0x2007, Regenerative Resistor Value
This specifies the resistance value for regenerative braking resistance. If it is set to 0, then it
uses the default resistance capacity embedded in the drive.
Index 0x2007 Regenerative Resistor Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RW No
0
to 1000
PRECYC ohm
0x2008, Regenerative Resistor Capacity
This specifies the current capacity for regenerative resistance. If it is set to 0, then it uses the
default resistance capacity embedded in the drive.
Index 0x2008 Regenerative Resistor Capacity
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RW No
0
to
30000
PRECYC Watt
0x2009, Overload Check Base
This indicates the load factor which triggers a continuous overload check. If it is set to 100 or
less, then the overload check starts early and the overload alarm triggers early.
Index 0x2009 Overload Check Base
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 100 UINT RW No
10
to 100
SV_OFF [%]

8-28
0x200A, Overload Warning Level
This specifies the level for the continuous overload warning signal output. The warning signal
is issued when it reaches the percentage value set relative to the alarm trigger value.
Index 0x200A Overload Warning Level
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 50 UINT RW Yes
10
to 100
SV_OFF [%]
0x200B, PWM Off Delay
This specifies the time span between the servo Off command and actual PWM Off. This
prevents the motor from slipping down the vertical axis while the servo Off command and
brake command order the motor brake to engage. Use a PWM off delay when operating a
motor brake through the output contact point brake signal. (range: 0-1000 ms, initial value:
10).
Index 0x200B PWM Off Delay
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 10 UINT RW No
0
to 1000
10 ms
0x200C, Dynamic Brake Control Mode
This specifies the Dynamic Brake (DB) control mode.
Index 0x200C Dynamic Brake Control Mode
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0x0 UINT RW No
0x0
to 0x3
SV_OFF -
Details
Value Setting details
0 Hold after a DB stop
1 Release after a DB stop
2 Release after free run stop
3 Hold after a free run stop

8-29
0x200D, Basic Function Configuration
This specifies the basic drive function.
Index 0x200D Basic Function Configuration
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0x00 UINT RW No
0x00 to
0xFF
SV_OFF -
Details
Bit function
Value
(Hex)
Setting details
0 Sets the servo drive direction
0 CCW (Clockwise), CW (Counterclockwise)
1 CW (Clockwise), CCW (Counterclockwise)
1 Sets the servo lock function
0 Do not use
1 Use
4 Set the multi-turn encoder
0 Use the multi-turn encoder as multi-turn
1 Use the multi-turn encoder as single-turn
0x200E, Position Scale Numerator
Index 0x200E Position Scale Numerator
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 1 INT RW No
1 ~
32767
SV_OFF -
0x200F, Position Scale Denominator
Index 0x200F Position Scale Denominator
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 1 INT RW No
1 ~
32767
SV_OFF -
0x2010, Velocity Scale Numerator
Index 0x2010 Velocity Scale Numerator
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 1 INT RW No
1 ~
32767
SV_OFF -

8-30
0x2011, Velocity Scale Denominator
Index 0x2011 Velocity Scale Denominator
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 1 INT RW No
1 ~
32767
SV_OFF -
0x2012, Acceleration Scale Numerator
Index 0x2012 Acceleration Scale Numerator
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 1 INT RW No
1 ~
32767
SV_OFF -
0x2013, Acceleration Scale Denominator
Index 0x2013 Acceleration Scale Denominator
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 1 INT RW No
1 ~
32767
SV_OFF -

8-31
0x2014, DAC Output
Index 0x2014 DAC Output
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 9 USINT RO No 0 to 9 Always -
Output Mode
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0x3210 UINT RW No
0x0000 to
0xFFFF
Always -
Channel 1 offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2 0 INT RW No
-32768 to
32767
Always Unit/V
Channel 2 offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
3 0 INT RW No
-32768 to
32767
Always Unit/V
Channel 3 offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
4 0 INT RW No
-32768 to
32767
Always Unit/V
Channel 4 offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
5 0 INT RW No
-32768 to
32767
Always Unit/V
Channel 1 Scale
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
6 0 UINT RW No
0
to 65535
Always Unit/V
8-32

Channel 2 Scale
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
7 500 UINT RW No
0
to 65535
Always Unit/V
Channel 3 Scale
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
8 50 UINT RW No
0
to 65535
Always Unit/V
Channel 4 Scale
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
9 50 UINT RW No
0
to 65535
Always Unit/V
Details
There are 4 DAC Output available and send out data according to setting with 200[usec] cycle time.
DAC Output Type
Type Data Type Data
0 Speed Feedback[RPM] 5 Following Error[pulse]
1 Speed Command[RPM] 6 DC Link Voltage[V]
2 Torque Feedback[%] D Speed Command(User)[RPM]
3 Torque Command[%] E Torque Command(User)[RPM]
4
Position Command
Frequency[0.1kpps]

DAC Output Offset
Set Offset[Unit/V] for analog output channel1~4.
(Speed[RPM], Torque[%], Position Command Frequency[0.1kpps], Position[pulse], DC_Link[V])
DAC Output Scale
If value of output is too low or high, output rate can be adjusted to high or low.
Set scale[Unit/V] of analog output channel1~4.
(Speed[RPM], Torque[%], Position Command Frequency[0.1kpps], Position[pulse], DC_Link[V])
8-33
Ex) 1channel scale 100 => Output 1[V] when 100[RPM].

0x2015, U Phase Current Offset
Set value of U Phase current offset. Value of current offset is already set in factory.
If you do not know the correct settings, dont set manually.
Index 0x2015 U Phase Current Offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 - INT RW No
-10000 ~
10000
SV_OFF [mA]

0x2016, V Phase Current Offset
Set value of V Phase current offset. Value of current offset is already set in factory.
Index 0x2016 V Phase Current Offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0
V Phase Current
Offset
INT RW No
-10000 ~
10000
SV_OFF [mA]

0x2017, W Phase Current Offset
Set value of W Phase current offset. Value of current offset is already set in factory.
Index 0x2016 W Phase Current Offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 - INT RW No
-10000 ~
10000
- [mA]

8-34
0x2020, Full Closed Control Mode
Index 0x2020 Full Closed Control Mode
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RW No 0 to 3 0 -
Details
0 Semi-Closed Control(control with only Internal encoder, default)
1 Full-Closed Control(Perform position control with external encoder)
2
Dual-Feedback Control(Semi-Closed Control when operation, Full-Closed
Control when stop)
0x2021, External Encoder Pitch
Index 0x2021 External Encoder Pitch
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 10000 DINT RW No
-1000000
to
1000000
PRECYC -
0x2022, External Encoder Type
Index 0x2022 External Encoder Type
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Details
0 Incremental-Encoder
1 Absolute-Encoder

8-35
0x2023, Dual-Feedback Conversion Level
Index 0x2023 Dual-Feedback Conversion Level
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 500 UINT RW No 0 to 5000 SV_OFF -
0x2024, Dual-Feedback Conversion Filter Time Constant

Index 0x2024 Dual Feedback Conversion Filter Time Constant
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x2025, External Encoder Following Error Window
AL-54(External encoder following error) will occur If following pulse-difference between
internal and external encoder is higher than value of setting in full closed control. Value of
Following error pulse will be reset as 0 when Servo OFF.
Index 0x2025 External Encoder Following Error Window
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 10000 UDINT RW No
0 to
2147483
647
SV_OFF -
0x2100, Inertia Ratio Setting
This sets the inertia ratio by calculating the load inertia from the machine system and rotor
inertia listed on the motor specification table.
Index 0x2100 Inertia Ratio
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 100 UINT RW No
0 to
20000
Always [%]
The inertia/load ratio is an important control parameter for the operation of the servo. It is
crucial to set the correct inertia ratio for optimal servo operation.

8-36
0x2101, Position P Gain 1
Index 0x2101 Position P Gain 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 50 UINT RW No 0 to 500 Always Hz
0x2102, Position P Gain 2
Index 0x2102 Position P Gain 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 70 UINT RW No 0 to 500 Always Hz
Position proportional gain [0x2101] and [0x2102]: Converts the difference between the position
command and the current position into a speed command by multiplying it by the position
proportional gain.
* Recommended value = speed proportional gain [0x2106]/10
0x2103, The Position Command Filter Time Constant
Index 0x2103 Position Command Filter Time Constant
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RW No 0 to 1000 Always ms
0x2104, Position Feed-forward Gain
Index 0x2104 Position Feed-forward Gain
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RW No 0 to 100 Always [%]
Feed-forward gain [0x2104]: Uses the differences in value to the position command to calculate the
gradient. Adds the speed command to the gradient to reduce the time needed to reach the target
position. If the value which results is too large, then the position controller may overshoot or
become unstable. It is important to gradually increase the value from a small value while monitoring
the test drive.

8-37
0x2105, The Position Feed-forward Filter Time Constant
Index 0x2105 Position Feed-forward Filter Time Constant
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
The feed-forward filter time constant [0x2105]: The feed-forward control filter vibrates if the position
command changes too drastically. If this occurs, configure the filter value until the vibrations
disappear.

0x2106, Speed P Gain 1
Index 0x2106 Speed P Gain 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 400 UINT RW No 0 to 5000 Always rad/s

0x2107, Speed P Gain 2
Index 0x2107 Speed P Gain 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 700 UINT RW No 0 to 5000 Always rad/s
Speed proportional gain [0x2106] and [0x2107]: Converts the speed error into a torque command
by multiplying it by the proportional gain.

0x2108, Speed Integral Time Constant 1 (Speed I Gain 1 Time
Constant)
Index 0x2108 Speed I Gain 1 Time Constant
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit

8-38
0x2109, Speed Integral Time Constant 2 (Speed I Gain 2 Time
Constant)
Index 0x2109 Speed I Gain 2 Time Constant
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Speed integral time constants [0x2108] and [0x2109]: Calculates the integral value of the speed
error. The speed error is the difference between the command speed and the current speed. The
speed integral time constant converts the speed error into a torque command by multiplying it by
the integral time constant.
0x210A, The Speed Command Filter Time Constant
Index 0x210A Speed Command Filter Time Constant
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x210B, The Speed Feedback Filter Time Constant
Index 0x210B Speed Feedback Filter Time Constant
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 5 UINT RW No 0 to 1000 Always 0.1ms
Speed feedback filter time constant [0x210B]: Filters the speed feedback to control vibrations when
the speed of the motor changes due to drive system vibrations or vibrations due to gain and too
much load inertia.
0x210C, The Torque Command Filter Time Constant
Use a digital filter for the analog torque command voltage to improve the stability of
command signals. If the filter value is set too high, responsiveness to torque commands
will be reduced. It is important to set a value that is appropriate for your system.
Index 0x210C Torque Command Filter Time Constant
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit

8-39
0x210D, Conversion Mode
Index 0x210D Conversion Mode
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0x00 UINT RW No
0x00 to
0xFF
Always -
1. Set the gain transfer mode.
Details
Bit function
Value
(Hex)
Setting details
0 to 3
Gain 1<->Gain 2 Conversion
Setting
0 Only uses gain 1.
1
ZSPD auto gain transfer
In case of zero speed, transfer from
gain 1 to gain 2.
In the opposite case, transfer from gain
2 to gain 1.
2
INPOS auto gain transfer
In case of IN position, transfer from
gain 1 to gain 2.
2 to gain 1.
3
Manual gain transfer
When the gain 2 contact is on, transfer
from gain 1 to gain 2.
2 to gain 1.
2. Setting the P and PI Control Conversion Modes
Details
Bit function
Value
(Hex)
Setting details
4 to 7 Set the P<->PI conversion
0 Only control PI.
1
Control P if the command torque is
higher than the set torque [0x2114].
2
Control P if the command speed is
higher than the set speed [0x2115].
3
Control P if the current acceleration is
higher than the set torque [0x2116].
4
Control P if the current position error is
higher than the set position error
[0x2117].
Note 1) Control P if the PCON contact is on (highest priority).
These functions allow you to improve position operations by applying the P control operation
stop function after PI control operation.

8-40
0x210E, The Gain Conversion Time
This sets the gain conversion time during gain conversion operation.
Index 0x210E Gain Conversion Time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
When converting gain 1 to gain 2 or gain 2 to gain 1, the conversion occurs according to the set
time.
0x210F, The Resonance Avoidance Operation (Notch Filter
Use)
Index 0x210F Notch Filter Use
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RW No 0 to 1 Always -
Mechanical resonance causes vibrations to occur at certain frequencies in certain systems.
You can control the vibrations by controlling the torque output for specific frequencies.
Details
Bit function
Value
(Hex)
Setting details
0 to 3
Resonance avoidance
operation
0 Do not use
1 Use
0x2110, The Resonance Avoidance Frequency (Notch Filter
Frequency)
Index 0x2110 Notch Filter Frequency
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x2111, The Resonance Avoidance Range (Notch Filter
Bandwidth)
Index 0x2111 Notch Filter Bandwidth
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit

8-41
0x2112, The Velocity Limit Switch
Index 0x2112 Velocity Limit Switch
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x2113, The Velocity Limit Value
Index 0x2113 Velocity Limit Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 2000 UINT RW No
0 to
10000
Always RPM
0x2114, P Control Conversion Torque (Torque Switch Value)
Index 0x2114 Torque Switch Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 200 UINT RW No 0 to 300 Always [%]
0x2115, The P Control Conversion Speed (Speed Switch
Value)
Index 0x2115 Speed Switch Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 50 UINT RW No 0 to 6000 Always [RPM]
0x2116, P Control Conversion Acceleration (Acceleration
Switch Value)
Index 0x2116 Acceleration Switch Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 100 UINT RW No 0 to 5000 Always rpm/s
0x2117, P Control Conversion Position Error (Following Error
Switch Value)
Index 0x2116 Following Error Switch Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 2000 UINT RW No
0 to
10000
Always Pulse
8-42
0x2200, Input Port Define 1
Index 0x2200 Input Port Define 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0x4000 UINT RW No
0x0000 to
0xFFFF
PRECYC -
0x2201, Input Port Define 2
Index 0x2201 Input Port Define 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0x0065 UINT RW No
0x0000 to
0xFFFF
PRECYC -
0x2202, Output Port Define 1
Index 0x2202 Output Port Define 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0x4321 UINT RW No
0x0000
to
0xFFFF
PRECYC -
0x2203, Output Port Define 2
Index 0x2203 Output Port Define 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0x0 UINT RW No
0x0000 to
0xFFFF
PRECYC -
0x2204, The Input Port Logic Set
Index 0x2204 Input Port Logic Set
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 UINT RW No
0b0000000000
to
0b1111111111
PRECYC -

8-43
0x2205, The Output Port Logic Set
Index 0x2205 Output Port Logic Set
Sub
Index
Initial
value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0b0110 UINT RW No
0b0000000000
to
0b1111111111
PRECYC -
0x2206, The Zero Speed Range
Index 0x2206 Zero Speed Range
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 10 UINT RW No 1 to 65535 Always RPM

Zero speed output range [0x2202]: A zero speed signal is output if the current speed drops below
the set speed.
Speed-reached range [0x606D]: The speed-reached signal is output.

Spee
Command speed
Velocity span
[0x606D]
Zero speed output range
[0x2206]
Zero speed (ZSPD)
Speed reached (INSPD)
Time
8-44
0x2207, The Break Output Speed
Index 0x2207 Break Output Speed
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit

0x2208, The Break Output Delay Time
Index 0x2208 Break Output Delay Time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit

The brake signal output operation speed [0x2207] and brake signal output delay time [0x2208]
If an alarm occurs after the servos built-in brake is applied to the vertical axis for motor operation,
then this feature activates to prevent the load on the vertical axis from falling to the motor brake.
This may occur as a result of the brake signal turning off because of the brake signal output
operation speed [0x2206] or the brake signal output delay time [0x2207].
0x2300, The Index (Z-phase) Pulse Detection Operation Speed
(Index Pulse Search Speed)
Index 0x2300 Index Pulse Search Speed
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit

Motor operation speed
Speed
Servo On input
Brake output signal
Within 50 ms
Brake signal output
operation speed
[0x2206]
Time
delay time [0x2208]
In case of servo Off or
alarm trigger
8-45
0x2301, The Speed Command Acceleration Time
Index 0x2301 Speed Command Acceleration Time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RW No
0 to
10000
Always ms
Acceleration time [0x2301]: Specifies the time required, in ms, for the motor to reach the rated
motor speed from zero speed.
0x2302, The Speed Command Deceleration Time
Index 0x2302 Speed Command Deceleration Time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RW No
0 to
10000
Always ms
Deceleration time [0x2302]: Specifies the time, in ms, required for the motor to stop after running at
the rated motor speed.
0x2303, The Speed Command S-curve Time
Index 0x2303 Speed Command S-curve Time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x2304, The Speed Operation Pattern (Acceleration Pattern)
Index 0x2304 Acceleration Pattern
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
You can configure the acceleration/deceleration operation in an S-curve pattern for smooth
acceleration/deceleration.
Details
0
Trapezoidal
-> Configure the acceleration/deceleration time in [0x2301] and [0x2302]
1
Sinusoidal
-> Configure the acceleration/deceleration time [0x2301] and [0x2302] + S-curve
time [0x2303]
0x2305, The Manual JOG Operation Speed (JOG Speed)
8-46
Index 0x2305 JOG Speed
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 500 INT RW No
-6000 to
6000
Always RPM

0x2306, JOG Operation Speed 1 (Program JOG Speed 1)
Index 0x2306 Program JOG Speed 1
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RW No
-6000 to
6000
Always RPM
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 3000 INT RW No
-6000 to
6000
Always RPM
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RW No
-6000 to
6000
Always RPM
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 -3000 INT RW No
-6000 to
6000
Always RPM
0x230A, JOG Operation Time 1 (Program JOG Time 1)
Index 0x230A Program JOG Time 1
Sub
Initial value
Data
Access
PDO Setting
Change Unit
8-47
Index 0x230A Program JOG Time 1
Index Type Mapping Range
0 500 UINT RW No
0 to
65535
Always ms
0x230B, JOG Operation Time 2 (Program JOG Time 2)
Index 0x230B Program JOG Time 2
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 5000 UINT RW No
0 to
65535
Always ms
0x230C, JOG Operation Time 3 (Program JOG Time 3)
Index 0x230C Program JOG Time 3
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 500 UINT RW No
0 to
65535
Always ms
0x230D, JOG Operation Time 4 (Program JOG Time 4)
A test drive repeats step 1 to 4.
Set the operation speed ([0x2306]-[0x2309]) and operation time ([0x230A]-[0x230D]) for
each step.
Index 0x230D Program JOG Time 4
Sub
Index
Name
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 5000 UINT RW No
0 to
65535
Always ms
0x2400, Electric Gear Ratio Mode (Electric Gear Mode)
Index 0x2400 Electric Gear Mode
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x2401, The Electric Gear Numerator Offset
Index 0x2401 Electric Gear Numerator Offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RW No
-30000 to
30000
Always -
8-48
0x2402, The Position Limit Function
Index 0x2402 Position Limit Function
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Details
Value(Hex) Setting details
0 Checking Software Position Limit value of forward direction
1 Checking Software Position Limit value of reverse direction
0x2403, Backlash Compensation
If the position operation causes backlashes which change the position, then this setting
converts backlash amount into a number of pulses to compensate for the backlash.
Index 0x2403 Backlash Compensation
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RW No
0 to
10000
Always -
0x2600, The Current Speed (RPM)
This displays the current operation speed in RPM.
Index 0x2600 Current Speed (RPM)
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 - INT RO Yes - - RPM
0x2601, The Command Speed (RPM)
This displays the current command speed in RPM.
Index 0x2601 Command Speed (RPM)
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 - INT RO Yes - - RPM
0x2602, The Tracking Position Pulse (Feedback Pulse)
This displays the accumulated number of position command pulses that result from servo
motor rotations when the servo turned on.
Index 0x2602 Feedback Pulse
8-49
Index 0x2602 Feedback Pulse
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 - DINT RO No - - Pulse
0x2603, The Position Command Pulse
This displays the accumulated number of position command pulses entered since the servo
turned on.
Index 0x2603 Command Pulse
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 - DINT RO No - - Pulse

0x2604, The Remaining Position Pulse (Following Error)
This displays the difference between command pulses and tracking pulses and the
remaining position pulses for the servo to run.
It ignores the remaining position pulses when a servo that is off is turned back on.
Index 0x2604 Following Error
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RO Yes - - Pulse
0x2605, The Input Command Frequency
This displays the input pulse frequency.
Index 0x2605 Input Command Frequency
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RO No - - KHz
0x2606, Current Operation Torque
This displays the energy (load) output by the servo motor as a percentage of the rated output.
Index 0x2606 Current Torque
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RO No - - [%]
0x2607, Current Command Torque
8-50
This uses the serv's control algorithm to calculate the internal torque command and display
it as a percentage of the rated torque.
Index 0x2607 Command Torque
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RO No - - [%]
0x2608, Accumulated Overload
This displays the current energy (load) as a percentage of the rated energy (load) of the
servo motor.
Index 0x2608 Accumulated Overload
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RO Yes - - [%]
0x2609, The Maximum Instantaneous Load
This displays the maximum (peak) load between the current time and the start of control after
the servo turns on as a percentage of the rated output.
Index 0x2609 Maximum Load
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RO No - - [%]
0x260A, The Torque Limit
This displays the maximum torque that the servo motor can output as a percentage of the
rated torque.
Index 0x260A Torque Limit
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 - INT RO No - - [%]
0x260B, The DC-Link Voltage
This displays the current DC link value of the main power.
The normal DC link voltage of a 220 V standard drive is approximately 300 V. The maximum
allowable DC link voltage is 405 V.
The overvoltage alarm [AL-41] goes off when the DC link voltage threshold is exceeded
because there is either too much or too little regenerative resistance.
The normal DC link voltage in the regenerative section is 385 V or below.
Index 0x260B DC-Link Voltage
8-51
Index 0x260B DC-Link Voltage
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RO Yes - - V
0x260C, Regenerative Overload
This displays the overload rate relative to the regenerative capacity of the servo drive.
Index 0x260C Regenerative Overload
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RO Yes - - [%]

0x260D, The Single-turn Data (Pulse) Display (Single-turn
Data)
This displays the single-turn data of the encoder in pulses.
Index 0x260D Single-turn Data
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x260E, The Single-turn Data (Degree) Display (Single-turn
Data (deg))
This displays the single-turn data of the encoder in degrees.
Index 0x260E Single-turn Data (deg)
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RO Yes - - Degrees
0x260F, The Multi-turn Data Display
This displays the multi-turn data for the encoder.
Index 0x260F Multi-turn Data
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RO Yes - - rev
0x2610, The Room Temperature Display
8-52
This displays the temperature sensor value of the servo drive in [ ].
Index 0x2610 Room temperature
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RO No - - [ ]

0x2611, The Motor Rated Speed Display
This displays the rated speed of the motor in RPM.
Index 0x2611 Motor Rated Speed
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RO No - - RPM
0x2612, The Motor Maximum Speed Display
This displays the peak speed of the motor in RPM.
Index 0x2612 Motor Maximum Speed
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RO No - - RPM
0x2613, The Motor Rated Current Display
This displays the rated current of the motor in A.
Index 0x2613 Motor Rated Current
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RO No - - A
0x2614, The U Phase Current Offset Display
This displays the U phase current offset in mA.
Index 0x2614 U Phase Current Offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RO No - - mA
0x2615, The V Phase Current Offset Display
This displays the V phase current offset in mA.
8-53
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RO No - - mA
0x2616, The FPGA Version Display
This displays the version of the FPGA.
Index 0x2616 FPGA Version
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 - UINT RO No - - -

0x2617, External Encoder Position Feedback
Index 0x2617 External Encoder Position Feedback
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Chan
ge
Unit
0 - DINT RO Yes - - [rev]
0x2618, External Encoder Following Error
Display Following pulse difference between Internal and External encoder.
Index 0x2618 External Encoder Following Error
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Chan
ge
Unit
0 - DINT RO Yes - - [rev]
0x2700, Read/Clear the Alarm History
Index 0x2700 Read/Clear Alarm History
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Clear History
Sub Initial value Data Access PDO Setting Change Unit
8-54
Index Type Mapping Range
1 0 UDINT RW No - - -
Alarm Code 1~20
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2~21 0 USINT RO No - - -
The L7N reads object entries to determine the alarm history of a parameter.
In order to prevent parameters from being incorrectly read, the Sub-Index records "read" when the
parameter is read.

The L7N reads object entries to delete the alarm history of a parameter.
In order to prevent parameters from being incorrectly deleted, record "rset" in the Sub-Index and an
alarm history is deleted.
When "read" is written to Sub-Index 1, all 20 alarm histories are read.
When "rset" is written to Sub-Index 1, all 20 alarm histories are deleted.
Alarm codes 1 to 20 is from 0x2700: 02 to 0x2700: 21.
The first alarm code is the most recent alarm.
You can check the past 20 alarm codes in sequence (the most recent first), by reading Sub-
Indexes 2 to 21.

0x2701, Auto Gain Tuning (Auto-tuning)
Index 0x2701 Auto-tuning
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
8-55
0 3 USINT RO No - SV_OFF -
Start tuning
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0 UDINT RW No - SV_OFF -
Tuning speed
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2 8 UINT RW No 1 to 10 SV_OFF
100
[RPM]
Tuning distance
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
The L7N reads object entries to automatically tune the gain.
In order to prevent parameters from being incorrectly tuned, the parameter is only tuned when the
Sub-Index records "tune."

Automatic tuning is conducted when "tune" is written to the Sub-Index 1.
This should be performed when the servo is off.
When writing "tune," the function begins to operate and repeats three times based on the set speed
and distance parameters.
Automatic gain tuning changes the inertia ratio (0x2100), speed proportional gain 1 (0x2106), and
speed integral time constant 1 (0x2108).
Set the automatic gain tuning speed in Sub-Index 2.
The default value is 8 in *100 RPM units.
Set the automatic gain tuning distance in Sub-Index 3.
It rotates 1.2 to 1.4 turns for motor shafts with a default value of 3, and about 25% of the distance
increases or decreases when the setting value is increased or decreased by 1.
It estimates the inertia based on the speed set in Sub-Index 2 and the distance set in Sub-
Index 3. It stores the inertia ratio [0x2100], speed proportional gain 1 [0x2106], and speed
proportional gain 2 [0x2108].
8-56

0x2702, Reset Absolute Encoder
Index 0x2702 Reset Absolute Encoder
Reset Absolute Encoder
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 1 USINT RW No - PRECYC -
Reset Encoder
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0 UDINT RW No - PRECYC -
0x2703, Calibrate Current Offset
Index 0x2703 Calibrate Current Offset
Calibrate Current Offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 1 USINT RW No - PRECYC -
Transfer distance
3 times
Speed
8-57
Calibrate Offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0 UDINT RW No - PRECYC -
L7N offers calibration-function for current offset.

Current Offset will be calibrated by writing rset in Sub-Index 1.

8.6 CiA402 Objects
0x603F, Error Code
This displays the most recent alarm/warning code generated by the servo drive.
Index 0x603F Error Code
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RO Yes - - -
0x6040, Controlword
This is composed of bits which control the drive state, the operation mode, and
manufacturer-specific options.
Index 0x6040 Controlword
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RW Yes
0 to
0xFFFF
Always -
Controlword Bit
8-58
Bit function Details
0 Switch on
Refer to the section concerning bits 0 to 3.
1 Enable Voltage
2 Quick stop
3 Enable operation
4 to 6
Settings by operation
mode
7 Fault reset 0-> 1: Alarm/warning reset
8 Halt
9
Settings by operation
mode
10 -
11 to
15
-

Details on Bits 0 to 3
Bits 0 to 3: Drive state control
Command
Controlword Bit
Bit 7 Bit 3 Bit 2 Bit 1 Bit 0
Shutdown 0 1 1 0
Switch on 0 0 1 1 1
Switch on +
Enable operation
0 1 1 1 1
Disable voltage 0 0
Quick stop 0 0 1
Disable operation 0 0 1 1 1
Enable operation 0 1 1 1 1
Bits 4, 5 and 9: Applied in Profile position (Pp) mode
Bit 9 Bit 5 Bit 4 Details
0 0 0 1
It proceeds to the next position when the operation at the current
position is complete.
8-59
Bit 9 Bit 5 Bit 4 Details
1 0 1 It drives to the next position immediately.
1 0 0 1
It drives from the current position to the profile position at the
profile speed before it applies the next position.
Bits 6 and 8: Applied in Profile position (Pp) mode
Bit function Value Details
6 Abs/rel
0 Sets the target position to an absolute value.
1 Sets the target position to a relative value.
8 Halt
0 Runs an operation or continues an operation.
1
Halts the operation according to the Halt Option code
(0x605D).
Bits 4, 5, 6, 8 and 9: Applied in Homing mode
4
Homing
operation
start
0 Does not perform the homing operation.
1 Performs or is performing the homing operation.
5 0 -
6 0 -
8 Halt
0 Runs the bit 4 command.
1
(0x605D).
9 0 Reserved

Bits 4, 5, 6, 8 and 9: Applied in Cyclic synchronous position (Csp) mode, velocity mode, or torque
mode.
4 0 -
5 0 -
6 0 -
8 Halt
0 Continues to perform the operation.
1
(0x605D).
9 0 -
Bits 4, 5, 6, 8 and 9: Applied at the Interpolated position (Ip)
Bit Function Value Details
4
Interpolation
enabled
0 Interpolation disabled
1 Interpolation enabled
5 0 -
6 0 -
8 Halt 0 Runs the bit 4 command.
8-60
Bit Function Value Details
1
(0x605D).
9 0 Reserved
Bits 4, 5, 6, 8 and 9: Applied in Profile velocity (Pv) mode or torque mode
4 0 Reserved
5 0 Reserved
6 0 Reserved
8 Halt
0 Continues to perform the operation.
1
(0x605D).
9 0 Reserved

0x6041, Statusword
The Statusword indicates the current state of the drive.
It consists of bits that indicate the state according to the drive and operation mode.
Index 0x6041 Statusword
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Chan
ge
Unit
0 0 UINT RO Yes
0 to
0xFFFF
- -
Statusword Bits
Bit Function Details
0 Ready to switch on
Refer to the section concerning bits 0 to 7. 1 Switched on
2 Operation enabled
8-61
Bit Function Details
3 Fault
4 Voltage enabled
5 Quick stop
6 Switch on disabled

7 Warning
8 Reserved
9 Remote Processed as a Controlword (0x6040)
10 Operation mode specific Refer to the sections concerning bits 10, 12 and 13.
11 Internal limit active Refer to the section concerning bit 11.
12 to 13 Operation mode specific Refer to the sections concerning bits 10, 12 and 13.
14 Torque limit active = 0; no torque limit active = 1; torque limit active
15 Reserved

Bits 0 to 7: Indicates the current state of the drive
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Drive State
0 0 0 0 0 Not ready to switch on
1 0 0 0 0 Switch on disabled
0 1 0 0 0 1 Ready to switch on
0 1 0 0 1 1 Switched on
0 1 0 1 1 1 Operation enabled
0 0 0 1 1 1 Quick stop active
0 1 1 1 1 Fault reaction active
0 1 0 0 0 Fault
1 Main Power On
8-62
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Drive State
1 Warning is occurred
Details about Bit 11
Bit 11: Indicates whether to use an internal limit
Use of an internal limit: Both the software position limit and internal limit are applied to the target
position.
Use N-OT/P-OT contacts
This exceeds the interpolation speed (only used for the interpolated position (Ip) or the cyclic
synchronous position (Csp))

Details on Bits 10, 12 and 13
Bits 10, 12 and13: Profile position (Pp) Mode
Bit State Value Details
10 Target reached
0
Halt (0x6040.8) = 0: Failed to reach the target position
Halt (0x6040.8) = 1: Deceleration
1
Halt (0x6040.8) = 0: Reached the target position
Halt (0x6040.8) = 1: Speed: 0
12
Set-point
acknowledge
0
Prepares the previous set point and waits for a new set
point
1 Changed from the previous set point to the new set point
13 Following error 0 No following error
8-63
1 Following error
Bits 10, 12 and 13: Homing Mode
Bit 13 Bit 12 Bit 10
Details
Homing
error
Homing
attained
Target
reached
0 0 0 Homing in progress
0 0 1 Homing stopped or not started
0 1 0 Performed homing operation, but the not reach the target
0 1 1 Homing completed
1 0 0 Homing error; speed not equal to 0
1 0 1 Homing error; speed equal to 0
Bits 10, 12 and 13: Cyclic synchronous position (Csp)/velocity mode/torque mode
10
Target
reached
0 Unable to reach the target (position/velocity/torque)
1 Reached the target (position/velocity/torque)
12
Target value
ignored
0 Ignores the target value (position/velocity/torque)
1 Uses the target value as the position control input
13 Following error
0 No following error (0 in Csv/constant in torque mode)
1 Following error

Bits 10, 12 and 13: Interpolated position (Ip) mode
10
Target
reached
0
Halt (0x6040.8) = 0: Unable to reach the target position
1
Halt (0x6040.8) = 1: Speed: 0
12 Ip mode active
0 Interpolation deactivated
1 Interpolation activated
13 0 -
10
Target
reached
0
8-64
Bits 10, 12 and 13: Profile velocity (Pv) mode
10
Target
reached
0
1
Halt (0x6040.8) = 1: Speed: 0
12 Speed
0 Not in a zero speed state
1 In zero a speed state
13 0 -
Bits 10, 12 and 13: Profile torque (Pt) mode
10 Target reached
0
Halt (0x6040.8) = 0: Failed to reach the target position
1
Halt (0x6040.8) = 1: Speed: 0
12 0 Reserved
13 0 Reserved

0x605A, The Quick Stop Option Code
This sets the Quick Stop option code.
Index 0x605A Quick Stop Option Code
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 2 INT RW No 0 to 4 - -
Details
Value Details
0 Not used (transits into Switch On Disabled).
1
Slowly decelerates and then stops the drive according to the quick stop
8-65
deceleration (0x6085) setting (Switch On Disabled).
2
Slowly decelerates and then stops the drive according to the quick stop
deceleration (0x6085) setting (Switch On Disabled).
3 Stops using the torque limit value (Switch On Disabled).
0x605B, The Shutdown Option Code
This specifies the operation to shutdown the servo drive (Operation Enabled state -> Ready
to Switch On state).
Index 0x605B Shutdown Option Code
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RW No 0 to 1 Always -
Details
Value Details
0 Not used
1 Decelerates to a stop; enters a Switch On Disabled state; enters a Ready state

0x605C, The Disable Operation Option Code
This sets the Disable Operation state (Operation Enabled state -> Switched On state) option
code.
Index 0x605C Disable Operation Option Code
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Details
Value Details
0 Does not use the drive function
8-66
Value Details
1
Decelerates to a stop; moves to the Switch On Disabled state; moves to the Not
Ready state
0x605D, The Halt Option Code
The Halt option code sets the operation method used to move from the Operation Enabled
state to the Switched On state.
Index 0x605D Halt Option Code
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Details
Value Details
1 Decelerates to a stop; moves to the Operation Enabled state
2
Decelerates to a stop based on the quick stop deceleration time; move to the
Operation Enabled state
3
Decelerates to a stop based on the torque limit; moves to the Operation Enabled
state

0x605E, The Fault Reaction Option Code
This sets the operation method which protects the L7N drive system during fault reactions.
Index 0x605D Fault Reaction Option Code
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RW No 0 Always -
Details
Value Details
0
Does not use the servo drive function. The motor maintains the free-run state
8-67
Value Details
(turns the servo Off).
0x6060, Modes of Operation
This sets the servo drive operation mode. The master sets the operation mode when the
power is turned on.
The L7N provides the following operation modes:
Index 0x6060 Modes of Operation
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 SINT RW Yes 0 to 10 Always -
Details
Value Name Details
0 - No mode change/no mode assigned
1 Pp Profile Position mode
2 - Reserved (keep last mode)
3 Pv Profile Velocity mode
4 Tq Profile Torque mode
6 Hm Homing mode
7 Ip Interpolated Position mode
8 Csp Cyclic Sync Position mode
9 Csv Cyclic Sync Velocity mode
10 Cst Cyclic Sync Torque mode
Other - Reserved (keep last mode)

0x6061, The Modes of Operation Display
This displays the current mode of operation.
The value displayed is identical to the operation mode (0x6060).
Index 0x6061 Modes of Operation Display
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 SINT RO Yes 0 to 10 - -
8-68
0x6062, The Position Demand Value
This displays the position demand value in the position units specified by the user.
Index 0x6062 Position Demand Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RO Yes - -
Pos.
unit
0x6063, The Position Actual Internal Value
This displays the actual internal position value in encoder pulses.
Index 0x6063 Position Actual Internal Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x6064, The Position Actual Value
This displays the actual position value in user-defined units.
Index 0x6064 Position Actual Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RO Yes - -
Pos.
unit

0x6065, The Position Error Range (Following Error Window)
This sets the position error range for the Following Error (Statusword, 0x6041.13).
Index 0x6065 Following Error Window
Sub
Inde
x
Initial value
Data
Type
Acces
s
PDO
Mappin
g
Setting
Range
Change
Uni
t
0 2000000
UDIN
T
RW No
0 to
1073741823
Always
Pos.
unit
8-69
0x6066, Position Error Timeout (Following Error Time Out)
This sets the position error timeout period.
Index 0x6066 Following Error Time Out
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x6067, The Position Reached Range (Position Window)
This sets the position reached range for the target.
If the L7N reaches the position window (0x6067) within the position window time (0x6068),
then it sets bit 10 of the Statusword (0x6041) to 1.
Index 0x6067 Position Window
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 100 UDINT RW No
0 to
1073741823
Always
Pos.
unit
0x6068, The Position Reached Time (Position Window Time)
This sets the time it takes to reach the target position.
If the L7N reaches the position window (0x6067) within the position window time (0x6068),
then it sets bit 10 of the Statusword (0x6041) to 1.
Index
0x6068
Position Window Time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit

0x606B, The Velocity Demand Value
This displays the position controller output or the trajectory generator output speed.
Index 0x606B Velocity Demand Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RO Yes - - Vel. unit
0x606C, The Actual Velocity Value
8-70
This displays the actual velocity value in user-defined position units.
Index 0x606C Actual Velocity Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RO Yes - - Vel. unit
0x606D, The Velocity Reached Range (Velocity Window)
This sets the range of the velocity window.
If the difference between the target velocity and the actual velocity is retained within the
velocity window range (0x606D) for the duration of the velocity window time (0x606E), then it
sets bit 10 of Statusword (0x6041) to 1.
This displays the window in user-defined units.
Index 0x606D Velocity Window
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 20000 UINT RW No 0 to 65535 Always
Vel.
unit
0x606E, The Velocity Window Time
This sets the velocity window time.
If the difference between the target velocity and the actual velocity is retained within the
velocity window range (0x606D) for the duration of the velocity window time (0x606E), then it
sets bit 10 of Statusword (0x6041) to 1.
Index 0x606E Velocity Window Time
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RW No
0 to
65535
Always ms

0x6071, The Target Torque
This displays the target torque for the motor in 0.1% increments of the rated torque.
Index 0x6071 Target Torque
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RW Yes
32768 to
+32767
Always [0.1%]
0x6072, Maximum Torque
8-71
This sets the maximum torque that the motor can output in 0.1% increments of the rated
torque.
This is the default maximum motor torque when power is first supplied to the servo drive.
Index 0x6072 Max. Torque
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 3000 UINT RW Yes 0 to 65535 Always [0.1%]
0x6074, The Torque Demand Value
This displays the current torque demand value in 0.1% increments of the rated torque.
Index 0x6074 Torque Demand Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RO Yes - Always [0.1%]
0x6076, The Motor Rated Torque
This displays the rated torque of the motor (mNm).
Index 0x6076 Motor Rated Torque
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UDINT RO No Always mNm

0x6077, The Torque Actual Value
This displays the actual torque value of the L7N in 0.1% increments of the rated torque.
Index 0x6077 Torque Actual Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RO Yes - - [0.1%]
0x607A, The Target Position
8-72
This sets the target position in Profile Position (Pp) mode and Cyclic Synchronous Position
(Csp) mode.
This position is applied as an abs/rel flag of the Controlword in Profile Position (Pp) mode
according to absolute/relative value setting. It is always applied as an absolute value in Csp
mode.
Index 0x607A Target Position
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 1310720 DINT RW Yes
2147483648
to
+2147483647
Always -
0x607C, The Home Offset
This sets the offset value for the origin of the absolute encoder or absolute external scale
and the zero position of the actual position value (0x6064).
Index 0x607C Home Offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RW No
536870912
to
+536870911
Always
Pos.
unit
Incremental encoder
If it finds the home position or it is at the home position, then the position moved by the home offset
value becomes the zero position.
Absolute encoder
If the absolute encoder is connected, then the home offset value is added to the absolute position
(the actual position value).

0x607D, The Software Position Limit
This sets the software limit value.
It limits the range of the position demand value (0x6062) and position actual value (0x6064)
and checks the new target positions for these ranges every time.
The software limit value is always relative to the mechanical origin.
The minimum software limit value is the reverse rotation limit. The maximum software limit
value is the forward rotation limit.
8-73
Index 0x607D Software Position Limit
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 2 DINT RW No Always -
Min. position limit
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 -2000000000 DINT RW No
536870912
to
536870911
Always
[Pos.
unit]
Max. position limit
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2 2000000000 DINT RW No
536870912
to
536870911
Always
[Pos.
unit]
0x607F, Maximum Profile Velocity
This sets the maximum profile velocity in profile mode.
Index 0x607F Max. Profile Velocity
Sub
Inde
x
Initial value
Data
Type
Acces
s
PDO
Mappin
g
Setting
Range
Change
Uni
t
0 2147483647
UDIN
T
RW Yes
0 to
429496729
5
Always
Vel.
unit

0x6081, The Profile Velocity
This sets the profile velocity in profile mode.
Index 0x6081 Profile Velocity
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 10000 UDINT RW Yes
0 to
4294967295
Always
Vel.
unit
8-74
0x6083, Profile Acceleration
This sets the acceleration in profile mode.
Index 0x6083 Profile Acceleration
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 20000 UDINT RW No
0 to
4294967295
Always
Acc.
unit
0x6084, Profile Deceleration
This sets the deceleration in profile mode.
Index 0x6084 Profile Deceleration
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 20000 UDINT RW No
0 to
4294967295
Always
Acc.
unit
0x6085, Quick Stop Deceleration
The system uses quick stop deceleration if the quick stop option code (0x605A) is set to 2.
Index 0x6085 Quick Stop Deceleration
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 100000 UDINT RW No
0 to
4294967295
Always
Acc.
unit
0x6087, The Torque Slope
This sets the torque slope in profile torque mode. It adjusts the rated torque per second in
0.1% increments.
Index 0x6087 Torque Slope
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 1000 UDINT RW Yes
0 to
4294967295
Always 0.1%/s
0x6098, The Homing Method
This sets the homing method. Refer to section 5.4, "Homing."
Index 0x6098 Homing Method
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 34 SINT RW Yes 0 to 35 Always -
Details
8-75
Value Details
0 Disabled
1 Homing using the index pulse and reverse limit contact
2 Homing using the index pulse and forward limit contact
7 to 14 Homing using the index pulse and home contact
24 Same as method 8 (does not use the index pulse)
28 Same as method 12 (does not use the index pulse)
33, 34 Homing to the index pulse
35 Homing to the current position
0x6099, Homing Speeds
This sets the homing speed in user-defined units.
Index 0x6099 Homing Speeds
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 2 UDINT RO No - - -
Speed during search for switch
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
4294967295
Always
[Vel.
unit]
Speed during search for zero
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 to
4294967295
Always
[Vel.
unit]
Setting value equation: X = (Pulses per revolution) * Setting speed (RPM) / 60
Ex) 19bit motor 3000 [RPM]setting X = 2
19
* 3000 / 60 X = 26214400
0x609A, Homing Acceleration
This sets the homing acceleration in user-defined units.
Index 0x609A Homing Acceleration
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 50000 UDINT RW No
0 to
4294967295
Always
Acc.
unit
Setting value equation: X = (Pulses per revolution) * Setting acceleration speed / 60
8-76
Ex) 19bit motor acceleration 3000 setting X = 2
19
* 3000 / 60 X = 26214400
0x60B1, The Velocity Offset
This sets the speed feed-forward value in Cyclic Synchronous Position (Csp) mode.
This also sets the offset value added to the speed reference in Cyclic Synchronous Position
(Csp) mode.
Index 0x60B1 Velocity Offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RW Yes
2147483648
to
+2147483647
Always
Vel.
unit
0x60B2, The Torque Offset
This sets the torque feed-forward value in Cyclic Synchronous Position (Csp) mode and
Cyclic Synchronous Velocity (Csv) mode. It also sets the offset value added to the torque
reference.
Index 0x60B2 Torque Offset
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 INT RW Yes
32768 to
+32767
Always [0.1%]
0x60B8, The Touch Probe Function
This sets the touch probe function.
Index 0x60B8 Touch Probe Function
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 51 UINT RW Yes
0 to
0xFFFF
Always -

Data Description
Bit Value Definition
0
0 Do not use touch probe 1.
1 Use touch probe 1.
1
0 Single trigger mode (latch at the first trigger event of the touch probe)
1
Continuous trigger mode (latch at the trigger event for each position
of the touch probe)
2
0 Trigger the input of touch probe 1.
1 Trigger the index pulse signal.
8-77
3 Reserved
4
0 Do not use sampling for the rising edge of touch probe 1.
1 Use sampling for the rising edge of touch probe 1.
5
0 Do not use sampling for the falling edge of touch probe 1.
1 Use sampling for the falling edge of touch probe 1.
6 to 7 Reserved
8
9
0 Single trigger mode (latch at the first trigger event of the touch probe)
1
Continuous trigger mode (latch at the trigger event for each position
of the touch probe)
10
0 Trigger the input of touch probe 2.
1 Trigger the index pulse signal.
11 Reserved
12
13
14 to 15 Reserved
0x60B9, The Touch Probe Status
This displays the status of the touch probe.
Index 0x60B8 Touch Probe Status
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UINT RO Yes - -
Data Description
0
1
0 Do not store the position value of the rising edge of touch probe 1.
1 Store the position value of the rising edge of touch probe 1.
2
0 Do not store the position value for the falling edge of touch probe 1.
1 Store the position value for the falling edge of touch probe 1.
3 to 5 Reserved
6 0, 1
Toggle whether to store all update values for the rising edge of touch
probe 1.
7 0, 1
Toggle whether to store all update values for the falling edge of touch
probe 1.
8
8-78
9
10
11 to 13 Reserved
14
probe 2.
15 1
probe 2.
In continuous trigger mode, you can toggle whether to save all update values for 6, 7, 14 and
15 bits on the rising/falling edge of the touch probe.
To disable bits 1, 2, 9 and 10 (saving the position values on the rising/falling edges of touch
probes 1 and 2) of the touch probe state (0x60B9), disable bits 4, 5, 12 and 13 (using
sampling on the rising/falling edges of touch probes 1 and 2) of the touch probe function
(0x60B8) and enable them.

0x60BA, The Touch Probe 1 Positive Edge Position Value
This displays the rising edge position value of touch probe 2.
Index 0x60BA Touch Probe 1 Positive Edge Position Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RO Yes -
Pos.
unit
0x60BB, The Touch Probe 1 Negative Edge Position Value
This displays the falling edge position value of touch probe 1.
Index 0x60BB Touch Probe 1 Negative Edge Position Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RO Yes -
Pos.
unit
0x60BC, The Touch Probe 2 Positive Edge Position Value
This displays the rising edge position value of touch probe 2.
Index 0x60BC Touch Probe 2 Positive Edge Position Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RO Yes -
Pos.
unit
8-79
0x60BD, The Touch Probe 2 Negative Edge Position Value
This displays the falling edge position value of touch probe 2.
Index 0x60BD Touch Probe 2 Negative Edge Position Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RO Yes -
Pos.
unit
0x60C1, The Interpolation Data Record
This records the interpolation data in Interpolated Position (Ip) mode.
Index 0x60C1 Interpolation Data Record
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 1 USINT RW No - - -
Interpolation data record
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
1 0 DINT RW Yes
2147483648
to
+2147483647
Always
[Pos.
unit]

0x60C2, The Interpolation Time Period
This sets the update interval for the interpolated position.
In the DC Sync0 mode, the interpolation time period is automatically set to the Sync0 cycle
time.
In the DC Free-run mode, the interpolation time period is set to the application cycle time of
the master.
The interpolation time period can be changed in a Switch on Disabled state.
8-80
Index 0x60C2 Interpolation time period
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
Interpolation time period
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 1 USINT RW No 1 to 250 Always -
Interpolation time index
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2 -3 SINT RW No 6 to 3 Always -
0x60E0, The Positive Torque Limit Value
This sets the torque limit value for forward driving in 0.1% increments of the rated torque.
Index 0x60E0 Positive Torque Limit Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x60E1, The Negative Torque Limit Value
This sets the torque limit value for reverse driving in 0.1% increments of the rated torque.
Index 0x60E1 Negative Torque Limit Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x60F4, The Following Error Actual Value
The following error actual value appears if a following error occurs.
Index 0x60F4 Following Error Actual Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RO Yes - -
Pos.
unit
0x60FC, The Position Demand Internal Value
8-81
This displays the values output by the trajectory generator in position mode. These values
appear as encoder increments.
Index 0x60FC Position Demand Internal Value
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0x60FD, The Digital Input
This indicates the digital input state of the L7N's CN1.
Index 0x60FD Digital Inputs
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 UDINT RO Yes - -
Details
Bit Input Details
0
N-OT: The reverse limit
switch
0: Off, 1: On
1
P-OT: The forward limit
switch
0: Off 1: On
2 Home switch 0: Off, 1: On
3 to 15 Reserved
16 DI#1:CN1-16pin 0: Switched off (Open), 1: Switched on (Close)
22 HWBB Hardwired base block signal input (0: Open, 1: Close)
23 to 31 Reserved

0x60FE, The Digital Output
This indicates the digital output state of the L7N's CN1.
Sub-Index 1 controls the actual output state.
Sub-Index 2 defines the logic of the Sub-Index 1 activated.
Index 0x60FE Digital Outputs
8-82
Number of entries
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 2 UDINT RW No - -
Physical outputs
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
1 0 UDINT RW Yes
0 to
0xFFFFFFF
F
Always -
Bit mask
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
2 0 UDINT RW No
0 to
0xFFFFFFF
F
Always -
Description of physical outputs
Bit Output Details
0 to 15 Reserved
16 DO#1:CN1 03-04 pin
Forced output (0: off, 1: on). Provided that 0x60FE:02.16 is
set to 1.
17 DO#2:CN1 23-24 pin
set to 1.
18 DO#3:CN1 25-26 pin
set to 1.
19 DO#4:CN1 01-02 pin
set to 1.
20 to 23 Reserved
24 DO#1:CN1 03-04 pin Hardware output state (0: off, 1: on).
28 to 31 Reserved
Description of the output mask
Bit Output Details
0 to 15 Reserved
16 DO#1:CN1 03-04 pin DO#1 Forced output enabled
8-83
Bit Output Details
20 to 31 Reserved

0x60FF, The Target Velocity
This sets the target velocity in user-defined units [Vel. unit] in Profile Velocity (Pv) mode and
Cyclic Synchronous Velocity (Csv) mode.
Index 0x60FF Target Velocity
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 0 DINT RW Yes
2147483648
to
+2147483647
Always
Vel.
unit
0x6502, Supported Drive Modes
This displays the drive modes that the L7N supports.
Index 0x6502 Supported Drive Modes
Sub
Index
Initial value
Data
Type
Access
PDO
Mapping
Setting
Range
Change Unit
0 1005 UDINT RO No - - -
Details
Bit Supported modes Details
0 Pp (Profile Position mode) 1: Supported
1 Vl (Velocity mode) 0: Not supported
2 Pv (Profile Velocity mode) 1: Supported
3 Tq (Profile Torque mode) 1: Supported
4 Reserved 0
5 Hm (Homing mode) 1: Supported
6 Ip (Interpolated Position mode) 1: Supported
7 Csp (Cyclic Sync Position mode) 1: Supported
8 Csv (Cyclic Sync Velocity mode) 1: Supported
9 Cst (Cyclic Sync Torque mode) 1: Supported
10 to 31 Reserved 0
10. Handling and Operation
9-1
9. Handling and Operation
9.1 Operation Checklist
Thoroughly check the following items during the test drive to prevent injuries or damage to
the servo motor.
9.1.1 Wiring Checklist
1. Is the voltage (AC 200 V) appropriate for the power input terminals?
2. Are the power cables (U, V, W, and FG) between the drive and the motor connected correctly?
3. Is the voltage (24 V) connected to the control signal correctly?
4. Is the regenerative resistance appropriate for the capacity and correctly connected?
5. Are the wiring cables free from bends or kinks?
6. Is the ground and wire insulation free from defects?
9.1.2 Drive Signal (CN1) Wiring Checklist
Confirm that the wire and contacts for the drive signals are in the state listed on the following
table.
Pin Number Pin Name
State of
Contact
Pin Number Pin Name
State of
Contact
16 PCON Off 14 HOME Off
17 GAIN2 Off 8 P-OT On
15 ALMRST Off 7 N-OT On
The previous table lists the factory default settings. You can allocate different values
according to the setting value of the input signal allocations ([0x2200] and [0x2201]) and
input signal logic definition ([0x2204]).
9.1.3 Surrounding Environment Checklist
Are there any metal filings or water around the wires?
9.1.4 Machine Status Checklist
1. Is the servo motor coupling in good condition?
2. Are the locking bolts fastened tightly?
3. Are there any obstacles that may prohibit operation of the machine?
10. Product Specifications
10-1
10.1 The Servo Motor
Heat Sink specification
Classification Standard (mm) Classification
AP04 250x250x6

Aluminum
AP06 250x250x6
AP08 250x250x12
AP13 350x350x20
AP18 550x550x30
AP22 650x650x35
Note 1) The data on the product features is measured when those heat sinks were applied.

10-2
10.1.1 Product Features
Servo Motor Type (APM-) SAR3A SAR5A SA01A SA015A
Applicable Drive (L7A) L7A001 L7A002
Rated Output [kW] 0.03 0.05 0.1 0.15
Rated torque
[Nm] 0.10 0.16 0.32 0.48
[kgfcm] 0.97 1.62 3.25 4.87
Instantaneous
maximum torque
[Nm] 0.29 0.48 0.96 1.43
[kgfcm] 2.92 4.87 9.74 14.62
Rated rotation
speed
[r/min] 3000
Maximum rotation
speed
[r/min] 5000
Inertia moment
[kgm2x10-4] 0.0164 0.02 0.05 0.06
[gfcms2] 0.0167 0.02 0.05 0.07
Allowable load inertia Motor inertia x 30 x 20
Rated power rate [kW/s] 5.56 10.55 23.78 35.34
Speed and
position detector
Standard Quad. Type Incremental 2048[P/R]
Option Serial Type (Coming soon)
Specifications
and features
Method of
protection
Fully closedself-cooling IP55 (excluding axis penetration)
Time rating Continuous
Ambient
temperature
0-40 [C]
Ambient
humidity
20-80[%] RH (no condensation)
Atmosphere No direct sunlight, corrosive gas, or combustible gas
Anti-
vibration
Vibration acceleration 49 [m/s2] (5G)
Weight [kg] 0.3 0.4 0.5 0.7
Rotation Speed - Torque Characteristics

APM-SAR3A
Repeatedly used area
Continuously used area
APM-SAR5A
APM-SAR015A
APM-SA01A
10-3
Product Features
Servo Motor Type (APM-) SB01A SB02A SB04A
Rated Output [kW] 0.10 0.2 0.4
Rated torque
[Nm] 0.32 0.64 1.27
[kgfcm] 3.25 6.49 12.99
Instantaneous
maximum torque
[Nm] 0.96 1.91 3.82
[kgfcm] 9.74 19.48 38.96
Rated rotation
speed
[r/min] 3000
Maximum rotation
speed
[r/min] 5000
Inertia moment
[kgm2x10-4] 0.11 0.18 0.32
[gfcms2] 0.12 0.19 0.33
Allowable load inertia Motor inertia x 20
Rated power rate [kW/s] 8.89 22.26 50.49
Speed and
position detector
Standard Quad. Type Incremental 3000[P/R]
Option Serial Type 19[bit]
Specifications
and features
Method of
protection
Fully closedself-cooling IP65 (excluding
axis penetration)

Ambient
temperature
0-40 [C]
Ambient
humidity
Atmosphere
No direct sunlight, corrosive gas, or
combustible gas

Anti-
vibration
Weight [kg] 0.8 1.1 1.6

APM-SB01A
APM-SB02A
APM-SB04A
10-4
Product Features
Servo Motor Type (APM-) SC04A SC06A SC08A SC10A
Applicable Drive (L7A) L7A004 L7A008 L7A010
Rated Output [kW] 0.4 0.6 0.8 1.0
Rated torque
[Nm] 1.27 1.91 2.55 3.19
[kgfcm] 12.99 19.49 25.98 32.48
Instantaneous
maximum torque
[Nm] 3.82 5.73 7.64 9.56
[kgfcm] 38.96 58.47 77.95 97.43
Rated rotation
speed
[r/min] 3000
Maximum rotation
speed
[r/min] 5000
Inertia moment
[kgm2x10-4] 0.67 1.09 1.51 1.93
[gfcms2] 0.69 1.11 1.54 1.97
Speed and
position detector
Standard Quadrature Type Incremental 3000[P/R]
Specifications
and features
Method of
protection
Ambient
temperature
0-40 [C]
Ambient
humidity
Anti-
vibration
Weight [kg] 1.9 2.5 3.2 3.8

APM-SC08A
APM-SC04A
APM-SC06A
APM-SC10A
10-5
Product Features
Servo Motor Type (APM-) SC03D SC05D SC06D SC07D
Rated Output [kW] 0.30 0.45 0.55 0.65
Rated torque
[Nm] 1.43 2.15 2.63 3.10
[kgfcm] 14.61 21.92 26.79 31.66
Instantaneous
maximum torque
[Nm] 4.30 6.45 7.88 9.31
[kgfcm] 43.84 65.77 80.38 94.99
Rated rotation
speed
[r/min] 2000
Maximum rotation
speed
[r/min] 3000
Inertia moment
[kgm2x10-4] 0.67 1.09 1.51 1.93
[gfcms2] 0.69 1.11 1.54 1.97
Speed and
position detector
Specifications
and features
Method of
protection
Ambient
temperature
0-40 [C]
Ambient
humidity
Anti-
vibration
Weight [kg] 1.9 2.5 3.2 3.9

APM-SC03D
APM-SC06D
APM-SC05D
APM-SC07D
10-6
Product Features
Servo Motor Type (APM-) SE09A SE15A SE22A SE30A SE06D SE11D
Applicable Drive (L7A) L7A008 L7A020 L7A035 L7A008 L7A010
Rated Output [kW] 0.9 1.5 2.2 3.0 0.6 1.1
Rated torque
[Nm] 2.86 4.77 7.00 9.55 2.86 5.25
[kgfcm] 29.23 48.72 71.45 97.43 29.23 53.59
Instantaneous
maximum
torque
[Nm] 8.59 14.32 21.01 28.64 8.59 15.75
[kgfcm] 87.69 146.15 214.3 292.29 87.69 160.76
Rated rotation
speed
[r/min] 3000 2000
Maximum
rotation speed
[r/min] 5000 3000
Inertia moment
[kgm2x10-4] 6.66 12.00 17.34 22.68 6.66 12.00
[gfcms2] 6.80 12.24 17.69 23.14 6.80 12.24
Rated power
rate
[kW/s] 12.32 18.99 28.28 40.20 12.32 22.98
Speed and
position
detector
Specifications
and features
Method of
protection
Ambient
temperature
0-40 [C]
Ambient
humidity
Anti-vibration Vibration acceleration 49 [m/s2] (5G)
Weight [kg] 5.5 7.5 9.7 11.8 5.5 7.5

APM-SE09A
APM-SE30A
APM-SE06D
APM-SE11D
APM-SE15A
APM-SE22A
10-7
Product Features
Servo Motor Type (APM-) SE16D SE22D SE03M SE06M SE09M SE12M
Rated Output [kW] 1.6 2.2 0.3 0.6 0.9 1.2
Rated torque
[Nm] 7.64 10.50 2.86 5.73 8.59 11.46
[kgfcm] 77.94 107.17 29.23 58.46 87.69 116.92
Instantaneous
maximum torque
[Nm] 22.92 31.51 8.59 17.19 25.78 34.37
[kgfcm] 233.83 321.52 87.69 175.30 263.06 350.75
Rated rotation
speed
[r/min] 2000 1000
Maximum
rotation speed
[r/min] 3000 2000
Inertia moment
[kgm2x10-4] 17.34 22.679 6.66 12.00 17.34 22.68
[gfcms2] 17.69 23.14 6.80 12.24 17.69 23.14
Rated power rate [kW/s] 33.65 48.64 12.32 27.35 42.59 57.89
Speed and
position detector
Specifications
and features
Method of
protection
Ambient
temperature
0-40 [C]
Ambient
humidity
Weight [kg] 9.7 11.8 5.5 7.5 9.7 11.8

APM-SE16D
APM-SE12M
APM-SE03M
APM-SE06M
APM-SE09M
APM-SE22D
10-8
Product Features
Servo Motor Type (APM-) SE05G SE09G SE13G SE17G SF30A SF50A
Applicable Drive (L7A) L7A008 L7A010 L7A020 L7 A035 L7 A050
Rated Output [kW] 0.45 0.85 1.3 1.7 3.0 5.0
Rated torque
[Nm] 2.86 5.41 8.28 10.82 9.55 15.91
[kgfcm] 29.23 55.21 84.44 110.42 97.43 162.38
Instantaneous
maximum torque
[Nm] 8.59 16.23 24.83 32.46 28.64 47.74
[kgfcm] 87.69 165.63 253.32 331.26 292.29 487.15
Rated rotation
speed
[r/min] 1500 3000
Maximum rotation
speed
[r/min] 3000 5000
Inertia moment
[kgm2x10-4] 6.66 12.00 17.34 22.68 30.74 52.13
[gfcms2] 6.80 12.24 17.69 23.14 31.37 53.19
Allowable load inertia Motor inertia x 10 Motor inertia x 5
Speed and
position detector
Specifications and
features
Method of
protection
Ambient
temperature
0-40 [C]
Ambient
humidity
Weight [kg] 5.5 7.5 9.7 11.8 12.4 17.7

APM-SE09G
APM-SE13G
APM-SE05G
APM-SE17G
APM-SF30A APM-SF50A
Repeatedly used area Repeatedly used area
Continuously used area Continuously used area
10-9
Product Features
Servo Motor Type (APM-) SF22D LF35D SF55D SF20G LF30G SF44G
Rated Output [kW] 2.2 3.5 5.5 1.8 2.9 4.4
Rated torque
[Nm] 10.50 16.71 26.26 11.46 18.46 28.01
[kgfcm] 107.17 170.50 267.93 116.92 188.37 285.80
Instantaneous
maximum torque
[Nm] 31.51 50.13 78.77 34.37 55.38 84.02
[kgfcm] 321.52 511.51 803.80 350.75 565.10 857.39
Rated rotation
speed
[r/min] 2000 1500
Maximum
rotation speed
[r/min] 3000 3000 2700 3000
Inertia moment
[kgm
2
x10
-4
] 30.74 52.13 85.31 30.74 52.13 83.60
[gfcms
2
] 31.35 53.16 83.60 31.37 53.19 85.31
Speed and
position detector
Standard Quadrature Type Incremental 3000[P/R] , L7N No application
Specifications
and features
Method of
protection
Ambient
temperature
0~40[C]
ambient humidity 20-80[%] RH (no condensation)
Atmosphere No direct sunlight, corrosive gas, or combustible gas.
Weight [kg] 12.4 17.7 26.3 12.4 17.7 26.3

APM-SF22D
APM-LF35D
APM-LF55D
10-10
Product Features
Servo Motor Type (APM-) SF12M SF20M LF30M SF44M
Rated torque [kW] 1.2 2.0 3.0 4.4
Rated torque
[Nm] 11.46 19.10 28.64 42.01
[kgfcm] 116.92 194.86 292.29 428.69
Instantaneous
maximum torque
[Nm] 34.37 57.29 85.93 126.04
[kgfcm] 350.75 584.58 876.88 1286.08
Rated rotation
speed
[r/min] 1000
Maximum
rotation speed
[r/min] 2000 1700 2000
Inertia moment
[kgm
2
x10
-4
] 30.74 52.13 83.60 121.35
[gfcms
2
] 31.37 53.19 85.31 123.83
Speed and
position detector
Standard
Quadrature Type Incremental 3000[P/R] , L7N No
application

Specifications
and features
Method of
protection
Ambient
temperature
0~40[C]
Weight [kg] 12.4 17.7 26.3 35.6

Continuously used area Continuously used area
10-11
Product Features
Servo Motor Type (APM-) SG20G LG30G SG44G SG22D LG35D SG55D
Applicable Drive (L7A) L7A020 L7A035 L7A050 L7A020 L7A035 L7A050
Rated torque [kW] 1.8 2.9 4.4 2.2 3.5 5.5
Rated torque
[Nm] 11.46 18.46 28.01 10.50 16.71 26.26
[kgfcm] 116.92 188.37 285.80 107.20 170.52 267.9
Instantaneous
maximum torque
[Nm] 34.47 55.38 84.02 31.51 50.13 78.77
[kgfcm] 350.80 565.10 857.39 321.52 511.51 803.8
Rated rotation
speed
[r/min] 1500 2000
Maximum
rotation speed
[r/min] 3000 2700 3000 3000
Inertia moment
[kgm
2
x10
-4
] 51.42 80.35 132.41 51.42 80.35 135.11
[gfcms
2
] 52.47 81.99 135.11 52.47 81.99 132.41
Speed and
position detector
Standard Quadrature Type Incremental 3000[P/R] , L7N No application
Specifications
and features
Method of
protection
Ambient
temperature
0~40[C]
Weight [kg] 17.0 22.0 30.8 17.0 22.0 30.8
APM-SG20G
APM-LG30G APM-SG44G
APM-SG55D
APM-SG22D
APM-LG35D
10-12
Product Features
Servo Motor Type (APM-) SG12M SG20M LG30M SG44M
Rated torque [kW] 1.2 2.0 3.0 4.4
Rated torque
[Nm] 11.46 19.10 28.64 42.01
[kgfcm] 116.92 194.86 292.29 428.69
Instantaneous
maximum torque
[Nm] 34.37 57.29 85.93 126.04
[kgfcm] 350.75 584.58 876.88 1286.08
Rated rotation
speed
[r/min] 1000
Maximum
rotation speed
[r/min] 2000 1700 2000
Inertia moment
[kgm
2
x10
-4
] 51.42 80.35 132.41 172.91
[gfcms
2
] 52.47 81.99 135.11 176.44
Speed and
position detector
Standard
Quadrature Type Incremental 3000[P/R] , L7N No
application

Specifications
and features
Method of
protection
Ambient
temperature
0~40[C]
Weight [kg] 17.0 22.0 30.8 37.5
10-13
Product Features
Servo Motor Type (APM-) HB01A HB02A HB04A HE09A HE15A
Applicable Drive (L7A) L7A002A L7A004A L7A008A L7A020A
Rated Output [kW] 0.1 0.2 0.4 0.9 1.5
Rated torque
[Nm] 0.32 0.64 1.27 2.86 4.77
[kgfcm] 3.25 6.49 12.99 29.23 48.72
Instantaneous
maximum torque
[Nm] 0.96 1.91 3.82 8.59 14.32
[kgfcm] 9.74 19.48 38.96 87.69 146.15
Rated rotation
speed
[r/min] 3000
Maximum
rotation speed
[r/min] 3500
Inertia moment
[kgm2x10-4] 0.27 0.333 0.46 19.56 22.27
[gfcms2] 0.274 0.34 0.47 19.96 22.72
Rated power rate [kW/s] 3.34 11.98 34.47 4.10 10.01
Speed and
position detector
Standard Quadrature Type Incremental 1024P/R 2048 P/R
Option x
Specifications
and features
Method of
protection
Ambient
temperature
0-40 [C]
Ambient
humidity
Weight [kg] 0.9 1.2 1.7 5.8 7.4

APM-HB01A
APM-HB02A
APM-HB04A
APM-HE09A
APM-HE15A
10-14
Product Features
Servo Motor Type (APM-)
Applicable Drive (L7A)
Rated Output
Rated torque

Instantaneous
maximum torque

Rated rotation
speed
Maximum
rotation speed
Inertia moment

Rated power rate
Speed and
position detector
Standard Serial Type 19[bit]
Option
Specifications
and features
Method of
protection
Ambient
temperature
0-40 [C]
Ambient humidity 20-80[%] RH (no condensation)
Weight

APM-FB01A
APM-FB04A
APM-FB02A
APM-FC04A
APM-FC06A
10-15
Product Features
Servo Motor Type
Rated Output
Rated torque

Instantaneous
maximum torque

Rated rotation
speed
Maximum
rotation speed
Inertia moment

Rated power rate
Speed and
position detector
Standard x
Option Fully closedself-cooling IP65 (excluding axis penetration)
Specifications
and features
Method of
protection
Continuous
Time rating 0-40 [C]
Ambient
temperature
Ambient humidity No direct sunlight, corrosive gas, or combustible gas
Atmosphere Vibration acceleration 49 [m/s2] (5G)
Anti-vibration x
Weight

10-16
Product Features
Servo Motor Type (APM-) FE09A FE15A FE22A FE30A FE06D FE11D
Rated output [kW] 0.9 1.5 2.2 3.0 0.6 1.1
Rated torque
[Nm] 2.86 4.77 7.00 9.55 2.86 5.25
[kgfcm] 29.20 48.70 71.40 97.40 29.2 0 53.60
Maximum
instantaneous
torque
[Nm] 8.59 14.32 21.01 28.65 8.59 15.75
[kgfcm] 87.70 146.10 214.30 292.20 87.70 160.70
Rated rotation
speed
[r/min] 3000 2000
Maximum rotation
speed
[r/min] 5000 3000
Inertia moment
[kgm2x10-4] 5.66 10.18 14.62 19.04 5.66 10.18
[gfcms2] 5.77 10.39 14.92 19.43 5.77 10.39
Speed and
position detector
Standard Serial Type 19 [bit]
Option X
Specifications
and features
Protection
method
Fully closedself-cooling IP65(excluding axis penetration)
Ambient
temperature
0~40[C]
Ambient
humidity
20~80[%]RH(no condensation)
Anti-vibration Vibration acceleration 49[m/s2](5G)
Weight [kg] 5.0 6.7 8.5 10.1 5.0 6.7
Rotation speed Torque Characteristics

10-17
Product Features
Servo Motor Type (APM-) FE16D FE22D FE03M FE06M FE09M FE12M
Rated output [kW] 1.6 2.2 0.3 0.6 0.9 1.2
Rated torque
[Nm] 7.63 10.5 2.86 5.72 8.59 11.46
[kgfcm] 77.90 107.10 29.22 58.4 87.7 116.9
Maximum
instantaneous
torque
[Nm] 22.92 31.51 8.59 17.18 25.77 34.22
[kgfcm] 233.80 321.40 87.66 175.3 262.9 349.1
Rated rotation
speed
[r/min] 2000 1000
Maximum rotation
speed
[r/min] 3000 2000
Inertia moment
[kgm2x10-4] 14.62 19.04 5.66 10.18 14.62 19.04
[gfcms2] 14.92 19.43 5.77 10.39 14.92 19.43
Speed and
position detector
Option X
Specifications
and features
Protection
method
Ambient
temperature
0~40[C]
Ambient
humidity
20~80[%]RH(no condensation_
Weight [kg] 8.5 10.1 5.0 6.7 8.5 10.1

10-18
Product Features
Servo Motor Type (APM-) FE05G FE09G FE13G FE17G FF30A FF50A
Rated output [kW] 0.45 0.85 1.3 1.7 3.0 5.0
Rated torque
[Nm] 2.86 5.41 8.27 10.82 9.55 15.91
[kgfcm] 29.22 55.19 84.41 110.38 97.40 162.30
Maximum
instantaneous
torque
[Nm] 8.59 16.23 24.82 32.46 28.65 47.74
[kgfcm] 87.66 165.57 253.23 331.14 292.3 487.00
Rated rotation
speed
[r/min] 1500 3000
Maximum rotation
speed
[r/min] 3000 5000
Inertia moment
[kgm2x10-4] 5.66 10.18 14.62 19.04 27.96 46.56
[gfcms2] 5.77 10.39 14.92 19.43 28.53 47.51
Speed and
position detector
Option X
Specifications
and features
Protection
method
Ambient
temperature
0~40[C]
Ambient
humidity
Weight [kg] 5.0 6.7 8.5 10.1 12.5 17.4

10-19
Product Features
Servo Motor Type (APM-)
Rated output
Rated torque

Maximum
instantaneous
torque
Rated rotation
speed
Maximum
rotation speed
Inertia moment

Rated power
rate
Speed and
position
detector
Option
Specifications
and features
Protection
method
Ambient
temperature
0~40[C]
Ambient
humidity
Weight

Continuously used
10-20
Protect Features
Servo Motor Type (APM-) FF12M FF20M FF30M FF44M
Applicable Drive (L7A) L7A020 L7A020 L7A035 L7A050
Rated output [kW] 1.2 2.0 3.0 4.4
Rated torque
[Nm] 11.46 19.09 28.64 42.02
[kgfcm] 116.9 194.8 292.2 428.7
Maximum
instantaneous
torque
[Nm] 34.38 57.29 85.94 126.1
[kgfcm] 350.70 584.40 876.60 128.60
Rated rotation
speed
[r/min] 1000
Maximum
rotation speed
[r/min] 2000 1700 2000
Inertia moment
[kgm
2
x10
-4
] 27.96 46.56 73.85 106.7
[gfcms
2
] 28.53 47.51 75.36 108.9
Rated power
rate
[kW/s] 46.94 78.27 111.04 165.38
Speed and
position
detector
Option X
Specifications
and features
Protection
method
Ambient
temperature
0~40[C]
Ambient
humidity
Weight [kg] 12.5 17.4 25.2 33.8

Continuously used
Continuously used
Continuously used
Continuously used
10-21
Protect Features
Servo Motor Type (APM-) FG22D FG35D FG55D FG20G FG30G FG44G
Rated output [kW] 2.2 3.5 5.5 1.8 2.9 4.4
Rated torque
[Nm] 10.50 16.71 26.25 11.50 18.50 28.00
[kgfcm] 107.1 170.4 267.8 116.9 188.4 285.8
Maximum
instantaneous
torque
[Nm] 31.51 50.12 78.76 34.40 55.40 84.00
[kgfcm] 321.30 511.30 803.4 350.80 565.1 857.4
Rated rotation
speed
[r/min] 2000 1500
Maximum
rotation speed
[r/min] 3000 2700 3000 3000 2700 3000
Inertia moment
[kgm
2
x10
-4
] 41.13 71.53 117.72 14.13 71.53 117.72
[gfcms
2
] 41.97 72.99 120.12 41.97 72.99 120.12
Rated power
rate
[kW/s] 26.78 38.99 58.51 31.91 47.66 66.64
Speed and
position
detector
Option X
Specifications
and features
Protection
method
Ambient
temperature
0~40[C]
Ambient
humidity
Weight [kg] 15.4 20.2 28.12 15.4 20.2 28.0

Continuously used Continuously used Continuously used
Continuously used
Continuously used
Continuously used
10-22
Product Features
Servo Motor Type (APM-) FG12M FG20M FG30M FG44M
Rated output [kW] 1.2 2.0 3.0 4.4
Rated torque
[Nm] 11.50 19.10 28.60
42.00

[kgfcm] 116.9 194.9 292.3
428.7

Maximum
instantaneous
torque
[Nm] 34.40 57.30 85.90
126.00

[kgfcm] 350.8 584.6 876.9
128.61

Rated rotation
speed
[r/min] 1000
Maximum
rotation speed
[r/min] 2000 1700 2000
Inertia moment
[kgm
2
x10
-4
] 41.13 71.53 117.72 149.40
[gfcms
2
] 41.97 72.99 120.12
152.45

Speed and
position detector
Option X
Specifications
and features
Protection
method
Ambient
temperature
0~40[C]
Ambient humidity 20~80[%]RH(no condensation)
Weight [kg] 15.4 20.2 28.0 33.5

Repeatedly used area Repeatedly used area Repeatedly used area
10-23
Electric Brake Specifications

Applicable Motor
Series
APM-SA APM-SB APM-SC APM-SE APM-SF APM-SG
Purpose Maintenance of stop(Refer to Note 2 below)
Input voltage [V] DC 24V DC 90V
Static friction torque
[Nm]
0.32 1.47 3.23 10.4 40 74
Capacity [W] 6 6.5 9 19.4 25 32
Coil resistance [] 96 89 64 29.6 23 327
Rated current [A] 0.25 0.27 0.38 0.81 1.04 0.28
Braking mechanism Spring brake
Insulation grade Grade F
Applicable Motor
Series
APM-FB APM-FC
Purpose
Maintenance of stop(Refer to
Note 2 below)

Input voltage [V] DC 24V
Static friction torque
[Nm]
1.47 3.23
Capacity [W] 6.5 9
Coil resistance [] 89 64
Rated current [A] 0.27 0.38
Braking mechanism Spring brake
Insulation grade Grade F
Note 1) The same specifications apply to all electric brakes installed in our servo motors.
Note 2) Electric brakes are designed to maintain a stop. Never use them for absolute braking.
Note 3) The characteristics of the electric brakes were measured at 20C.
Note 4) These brake specifications are subject to change. Check the voltage specifications on your
specific motor.
10-24
10.1.2 Outline Diagram
SA Series | APM-SAR3A, APM-SAR5A, APM-SA01A,
APM-SA015A

Name
ExternalDimensions
Weight(kg)
L LM LC CB
SAR3A 101.3(137.6) 76.3(112.6) 42.5(42.4) 66.3(102.3) 0.32(0.67)
SAR5A 108.3(144.6) 83.3(119.6) 49.5(49.4) 73.3(109.3) 0.38(0.73)
SA01A 125.3(161.6) 100.3(136.6) 66.5(66.4) 90.3(126.3) 0.5(0.85)
SA015A 145.3 120.3 86.5 110.3 0.7

Note 1) The standard shaft end for 40 flange model is a straight shaft end.
Note 2) Use DC power (24 V) to operate the brake.
Note 3) The sizes in parentheses apply when attached to the brakes.(Except SA015A)

10-25
SB Series | APM-SB01A, APM-SB02A, APM-SB04A

Name
ExternalDimensions
Weight(kg)
L LM LC CB
SB01A 122(162) 92(132) 52.5(52.3) 59.5(99.5) 0.82(1.4)
SB02A 136(176) 106(146) 66.5(66.3) 73.5(113.5) 1.08(1.66)
SB04A 1634(199) 134(169) 94.5(94.3) 101.5(141.5) 1.58(2.16)

Note 2) The sizes in parentheses apply when attached to the brakes.

10-26
SC Series | APM-SC04A,SC03D, APM-SC06A,SC05D,
APM-SC08A,SC06D, APM-SC10A,SC07D

Name
ExternalDimensions
Weight
(kg)
L LM LC CB S
SC04A,SC03D 158.5(199.8) 118.5(158.8) 79(78.8) 86(126.3) 14 1.88(2.92)
SC06A,SC05D 178.5(218.8) 138.5(178.8) 99(98.8) 106(146.3) 16 2.52(3.56)
SC08A,SC06D 198.5(238.8) 158.5(198.8) 119(118.8) 126(166.3) 16 3.15(4.22)
SC10A,SC07D 218.5(258.8) 178.5(218.8) 139(138.8) 146(186.3) 16 3.80(4.94)


SE Series | APM-SE09A, SE06D, SE05G, SE03M,
APM-SE15A, SE11D, SE09G, SE06M,
APM-SE22A, SE16D, SE13G, SE09M,
APM-SE30A, SE22D, SE17G, SE12M
10-27

Name
ExternalDimensions
Key
Dimension
s
Weight(kg)
L LM LC S T W U
SE09A,SE06D,SE05G,SE03M 201.3(239.3) 143.3(181.3) 93.8(93.6) 19 5 5 3 5.5(7.04)
SE15A,SE11D,SE09G,SE06M 225.3(263.3) 167.3(205.3) 117.8(117.6) 19 5 5 3 7.54(9.08)
SE22A,SE16D,SE13G,SE09M 249.3(287.3) 191.3(229.3) 141.8(141.6) 22 6 6 3.5 9.68(11.22)
SE30A,SE22D,SE17G,SE12M 273.3(311.3) 215.3(253.3) 165.8(165.6) 22 6 6 3.5 11.78(13.32)


SF Series | APM-SF30A, SF22D, SF20G, SF12M,
APM-SF50A, LF35D, LF30G, SF20M,
APM-SF55D, SF44G, LF30M
APM-SF44M
10-28

Name
External Dimensions
Weight
(kg)
L LM LC
SF30A, SF22D, SF20G, SF12M 261.5(312.9) 182.5(233.9) 133(132.7) 12.4(19.2)
SF50A, LF35D, LF30G, SF20M 295.5(346.9) 216.5(267.9) 167(166.7) 17.7(24.9)
SF55D, SF44G LF30M 345.5(396.9) 266.5(317.9) 217(216.7) 26.3(33.4)
SF44M 405.5(456.9) 326.5(377.9) 277(276.7) 35.6(42.8)

Note 1) SF30M or above models have eye bolts.

SG Series | APM-SG22D, SG20G, SG12M,
APM-LG35D, LG30G, SG20M,
APM-SG55D, SG44G, LG30M,
APM-SG44M
10-29

Name
External Dimensions
Weight(kg)
L LM LC
SG22D, SG20G,SG12M 236.5(302.7) 171.5(237.7) 122(121.2) 16.95(30.76)
LG35D,LG30G,SG20M 256.5(322.7) 191.5(257.7) 142(142.2) 21.95(35.7)
SG55D, SG44G,LG30M 292.5(358.7) 227.5(293.7) 178(177.2) 30.8(44.94)
SG44M 320.5(386.7) 255.5(321.7) 206(205.2) 37.52(50.94)


APM-HB01A (Hollow Shaft), APM-HB02A (Hollow Shaft),
APM-HB04A (Hollow Shaft)
10-30

Name
External Dimensions
Weight (kg)
L LM LC CB
Hollow
Shaft
Diameter
HB01A 140.5 98.5 63.5 25 15 0.89
HB02A 154.5 112.5 77.5 39 15 1.16
HB04A 182.5 140.5 105.5 66 15 1.69
APM-HE09A (Hollow Shaft), APM-HE15A (Hollow Shaft)

Name
External Dimensions
Weight (kg)
L LM LC
Hollow
Shaft
Diameter
HE09A 207 150 111.5 40 5.82
HE15A 231 174 135.5 40 7.43
FB Series : APM-FB01A, APM-FB02A, APM-FB04A
10-31

Name
External Dimensions
Weight(kg)
L LM LC
FB01A 109(149.2) 79(119.2) 43.5(43) 0.72(1.3)
FB02A 120(160.2) 90(130.2) 54.5(54) 0.94(1.49)
FB04A 140(150.2) 110(150.2) 74.5(74) 1.32(1.87)
Note 1) Use DC power (24V) to operate the brake.
10-32
FC Series | APM-FC04A,FC03D, APM-FC06A,FC05D,
APM-FC08A,FC06D, APM-FC10A,FC07D

Name
External Dimensions Shaft, Key Dimensions
Weight(kg)
L LM LC S H T W U
FC04A,FC03D 136.5(177) 96.5(137) 61(60.5) 14 -0.018 5 5 3 1.56(2.6)
FC06A,FC05D 154.5(195) 114.5(155) 79(78.5) 19 -0.021 6 6 3.5 2.18(3.22)
FC08A,FC06D 172.5(213) 132.5(173) 97(96.5) 19 -0.021 6 6 3.5 2.72(3.76)
FC10A,FC07D 190.5(231) 150.5(191) 115(114.5) 19 -0.021 6 6 3.5 3.30(4.34)

10-33
FE Series | APM-FE09A, FE06D, FE05G, FE03M,
APM-FE15A, FE11D, FE09G, FE06M,
APM-FE22A, FE16D, FE13G, FE09M,
APM-FE30A, FE22D, FE17G, FE12M

<Standard>
Name
External Dimensions Key Dimensions
Weight(kg)
L LM LC S QW T W U
FE09A,FE06D,FE05G,FE03M 197.3 139.3 89.8 19 25 5 5 3 5.04
FE15A,FE11D,FE09G,FE06M 217.3 159.3 109.8 19 25 5 5 3 6.74
FE22A,FE16D,FE13G,FE09M 237.3 179.3 129.8 22 25 6 6 3.5 8.48
FE30A,FE22D,FE17G,FE12M 255.3 197.3 147.8 24 25 7 8 4 10.05

<Brake>
Name
Weight(kg)
L LM LC S QW T W U
FE09A,FE06D,FE05G,FE03M 235.3 177.3 89.6 19 25 5 5 3 6.58
FE15A,FE11D,FE09G,FE06M 255.3 197.3 109.6 19 25 5 5 3 8.28
FE22A,FE16D,FE13G,FE09M 275.3 217.3 129.6 22 25 6 6 3.5 10.02
FE30A,FE22D,FE17G,FE12M 294 236 148 24 36 7 8 4 11.59
10-34
FF Series | APM-FF30A, FF22D, FF20G, FF12M,
APM-FF50A, FF35D, FF30G, FF20M,
APM-FF30M, FF55D, FF44G, APM-FF44M

<Standard>
Name
Weight(kg)
L LM LC LR S QK T W U
FF30A,22D,20G,12M 258 179 129
79
35 60 8 10 5
12.5
FF50A,35D,30G,20M 288 209 159 17.4
44G,30M 332 253 203 25.2
44M 385 306 256 42 60 8 12 5 33.8

<Brake>
Name
Weight(kg)
L LM LC S T W U
FF30A,FF22D,FF20G,FF12M 308.9 229.9 128.7
35
(0~+0.01)
8 10 5
19.7
FF50A,FF35D,FF30G,FF20M 338.9 259.9 158.7 24.6
FF55D,FF44G,FF30M 382.9 303.9 202.7 32.4
FF44M 435.9 356.9 234.7
42
(-0.016~0)
8 12 5 41.0
10-35

Note 1) FF30M or above models have eye bolts.
FG Series | APM-FG22D, FG20G, FG12M,
APM-FG35D, FG30G, FG20M,
APM-FG55D, FG44G, FG30M,
APM-FG44M

<Standard>
Name
Weight(kg)
L LM LC S T W U
FG22D,FG20G,FG12M 229.5 164.5 115
35
(0~+0.01)
8 10 5
15.42
FG35D,FG30G,FG20M 250.5 185.5 136 20.22
FG55D,FG44G,FG30M 282.5 217.5 168 28.02
FG44M 304.5 239.5 190
42
(-0.016~0)
8 12 5 33.45

<Brake>
Name
Weight(kg)
L LM LC LR S QK T W U
FG22D,FG20G,FG12M 296 231 115
65 35 60 50 8 10
29.23
FG35D,FG30G,FG20M 317 252 136 34.03
10-36
FG44G,FG30M 349 284 168 41.83
FG44M 371 306 190 42 60 50 8 12 47.26
10.2 The Servo Drive
10.2.1 Product Features
Name
Item
L7NA
001B
L7NA
002B
L7NA
004B
L7NA
008B
L7NA
010B
L7NA
020B
L7NA
035B
L7NA
050B
Input power
Main power 3-phase AC 200-230 V (-15-10[%]), 50-60 [Hz]
Control power Single-phase AC 200-230 V (-15-10[%]), 50-60 [Hz]
Rated current (A) 1.4 1.7 3.0 5.2 6.75 13.5 16.7 32
Peak current (A) 4.2 5.1 9.0 15.6 20.25 40.5 50.1 96
Encoder Type Serial 17 bit/19 bit/21 bit
Control
performance
Speed control
range
Maximum 1: 5000
Frequency response Maximum 1 kHz or more (when the 19-bit serial encoder is applied)
Speed change rate
0.01% or lower (when the load changes between 0 and 100%)
0.1% or less (temperature of 25 (10))
Torque control
repetition accuracy
Within 1%
Supported drive modes
(CiA402)

Profile Velocity Mode
Profile Torque Mode
Cyclic Synchronous Position Mode
Cyclic Synchronous Velocity Mode
Cyclic Synchronous Torque Mode
Homing Mode
Digital
input/output
Digital input
Total 6 input channels (allocable)
PCON, GAIN2, ALMRST, HOME, P-OT, N-OT
Above 6 functions can be used selectively for assignment.
Signal can be set as positive logic or negative logic.
Touch probe input
There are 2 input channels.
Provides rising and falling edge detection functions for each channel.
Digital output
Total 4 channels (allocable)
ALARM, READY, ZSPD, BRAKE, INPOS, INSPD, WARN
Above 7 outputs can be used selectively for assignment.
10-37
Name
Item
L7NA
001B
L7NA
002B
L7NA
004B
L7NA
008B
L7NA
010B
L7NA
020B
L7NA
035B
L7NA
050B
Signal can be set as positive logic or negative logic.
Additional
communication
USB Program download is available with USB Communication.
Built-in functions
Dynamic
braking
Standard built-in brake (activated when the servo alarm goes off or when the servo
is off).
Regenerative
braking
Both the default built-in brake and an externally installed brake are possible.
Display
function
Seven segments (5 DIGIT)
Self-setting
function
The [Mode] key changes the content displayed in the 7 segments.
Additional
function
Auto gain tuning function
Protection
function
Overcurrent, overload, overvoltage, low voltage, main power input error, control
power input error, overspeed, motor cable, heating error (power module heating,
drive temperature error), encoder error, excessive regeneration, sensor error,
communication error
Environment
Temperature 0 ~ 50[ ]
Humidity 90% RH or less (no condensation)
Environment Indoors in an area free from corrosive or combustible gases, liquids, or dust.

10-38

10.3 Outline Diagram
L7NA001B - L7NA004B

Weight: 1kg
L7NA008B ~ L7NA010B
10-39

Weight: 1.5 kg (including the cooling fan)
L7NA020B ~ L7NA035B


10-40
L7NA050B

10.4 Options and Peripheral Devices
Option (serial encoder cable)
Category
Product
Name
Name (Note 1)
Applicable
Motors
Specifications
For
signaling
Serial type
encoder
cable
(Small
capacity)
APCS-
ECS
All models
of
APM-SA,
(Coming)
APM-SB,
and
APM-SC
Series

1. Motor connection
a. Cap specifications (9 positions): 172161-1 (AMP)
b. Socket specifications: 170361-1 (AMP)
2. Drive connection (CN2)
a. Case specifications: 10314-52A0-008 (3M)
b. Connector specifications: 10114-3000VE (3M)
3. Cable specifications: 3Px0.2SQ or 3Px24AWG
Drive connection (CN2) Motor connection
10-41
For
signaling

Multiturn
type
encoder
cable
(Small
capacity)

APCS-
ECS1

All models
of
APM-SA,
(Coming)
APM-SB,
and
APM-SC
Series

1. Motor connection
a. Case specifications: 10314-52A0-008 (3M) or
SM-14J(Suntone)
b. Connector specifications: 10114-3000VE (3M) or
SM-14J(Suntone)
Note 1) The in the name indicates the type and length of each cable. Refer to the following table for
this information
Cable length (m) 3 5 10 20
Robot cable F03 F05 F10 F20
Regular cable N03 N05 N10 N20

Category
Product
Name
Name (Note
1)
Applicable
Motors
Specifications
For
signaling
Flat motor
type
encoder
cable
(small
capacity)
APCS-
EES-

*Front :
APCS-
EES
(Load
direction)

* Rear :
APCS-
EES-R
(Rear
direction)
All models
of
APM-FB
APM-FC
Series
1.
1. Motor connection
a. Cap specifications: 2201825-1(Tyco)
b. Socket specifications : 2174065-4(Tyco )
a. Case specifications: 10314-52A0-008(3M) or
SM-14J(Suntone)
b. Connector specifications: 10114-3000VE(3M) or
SM-14J(Suntone)
3. Cablespecifications:3Px0.2SQor3Px24AWG
Motor connection Drive connection (CN2)
10-42
For
signaling
Multiturn
type
encoder
cable
(small
capacity)
APCS-
EES1-

*Front :
APCS-
EES1
(Load
direction)

* Rear :
APCS-
EES1-R
(Rear
direction)
All models
of
APM-FB
APM-FC
Series

1. Motor connection
a. Cap specifications: 2201825-1(Tyco)
b. Socket specifications : 2174065-4(Tyco )
SM-14J(Suntone)
b.Connector specifications: 10114-3000VE(3M) or
SM-14J(Suntone)

this information

Category
Product
Name
Name (Note
1)
Applicable
Motors
Specifications
For
signaling
Serial type
encoder
cable
(medium
capacity)
APCS-
EDS
All models
of
APM-SE
APM-SF
APM-SG
APM-LF
APM-LG
APM-FE
APM-FF
APM-FG
Series

1. Motor connection (MS:Military Standard)
a. Plug specifications : MS3108B(MS3106B) 20-29S
SM-14J(Suntone)
b. Connector specifications: 10114-3000VE(3M) or
10-43
SM-14J(Suntone)
For
signaling
Multiturn
type
encoder
cable
(medium
capacity)
ACS-
EDS1
All models
of
APM-SE
APM-SF
APM-SG
APM-LF
APM-LG
APM-FE
APM-FF
APM-FG
Series

1. Motor connection
a. Cap specifications (9 Position) : 172161-1(AMP)
b. Socket specifications : 170361-1(AMP)
a. Case specifications : 10314-52A0-008(3M) or
SM-14J(Suntone)
b. Connector specifications : 10114-3000VE(3M) or
SM-14J(Suntone)
3. Cable specifications : 4Px0.2SQ or 4Px24AWG
Note 1) The in the name indicates the type and length of each cable. Refer to the following table
for this information
Optional power cable
Category
Product
Name
Name
(Note 1)
Applicable
Motors
Specifications
For power
Standard
power
cable
(Small
capacity)
APCS-
PGS
All models
of
APM-SA,
APM-SB,
APM-SC
and
APM-HB
Series

1. Motor connection
2. Drive connection (U, V, W, and FG)
a. 1) U,Vand W pin specifications:UA-F1512(SEOIL)
b. 2) FG pin specifications: 1.5-4 (Ring terminal)
Motor connection
Drive connection
10-44
Category
Product
Name
Name
(Note 1)
Applicable
Motors
Specifications
3. Cable specifications: 4Cx0.75SQ or 4Cx18(AWG18)

For power
Brake
power
cable
(Small
capacity)
APC-
PKB
All models
of
APM-SA
APM-SB
APM-SC
Series

1. Motor connection
2. For braking power
a. Connection terminal specifications: 1.5x3 (Ring Terminal)
b. Cable specifications: 2Cx0.75SQ or 2Cx18 (AWG18)

(DC24V) Motor connection Power Supply
10-45
Category
Product
Name
Name
(Note 1)
Applicable
Motors
Specifications
For power
Standard
power
cable
APCS-
PHS
All models
of
APM-SE
APM-FE
APM-HE
Series

1. Motor connection (MS : Military Standard)
a. Plug specifications: MS3108B(MS3106B)20-4S
2. Drive connection (U,V,W,FG)
a. U, V and W pin specifications: 2512
b. FG pin specifications: 2.5x4(Ring Terminal)
3. Cable specifications: 4Cx2.5SQ or 4Cx14AWG

For power

Power
cable
(brake
type)

APCS-
PNB

All models
of
APM-SE
APM-FE
Series

1. Motor connection
a. Plug specifications: MS3108B20-15S(MS )
2. Drive connection
a. U, V and W pin specifications: 2012
b. Cable specifications: 4C x 2.5SQ or 4C x 12AWG
c. FG pin specifications: 2.5 x 4(Ring Terminal)
3. Brake power connection
a. BK pin specifications: 1.5 x 3(Ring Terminal)
b. Cable specifications: 2C x 0.75SQ or 2C x 18AWG
Motor connection Drive connection
<Motor connection>
10-46
Category
Product
Name
Name
(Note 1)
Applicable
Motors
Specifications
For power
Standard
power
cable
APCS-
PIS
All models
of
APM-SF
APM-SG
APM-FF
APM-FG
Series
Below
3.5KW

a. U, V and W pin specifications: F2512
b. FG pin specifications: 2.5x4 (Ring Terminal)

For power

Power
cable
(brake
type)

APCS-
PPB

All models
of
APM-SF
APM-LF
APM-FF
Series
Below
3.5KW

1. Motor connection
a. Plug specifications: MS3108B24-10S(MS )
2. Drive connection
a. Cable specifications: 4C x 2.5SQ or 4C x 14AWG
b. pin specifications: 2.5 x 4(Ring Terminal)
b. pin specifications: 2C x 0.75SQ or 2C x 18AW
<Motor connection>
10-47
Category
Product
Name
Name
(Note 1)
Applicable
Motors
Specifications

For power

Standard
power
cable
APCS-
PJS
(new
model)
All models
of
APM-SF
APM-SG
APM-FF
APM-FG
Series
above
3.5KW
below
5KW
a. U,V and W pin specifications: 6012
b. FG pin specifications: 6.0 x 5 (Ring Terminal)

For power

Power
cable
(brake
type)

APCS-
PLB
(new
model)
All models
of
APM-SF
APM-LF
APM-FF
Series
above
3.5KW
below
5KW

1. Motor connection
a. Plug specifications: MS3108B24-10S(MS)
2. Drive connection
a. Cable specifications: 4C x 2.5SQ or 4C x 14AWG
b. pin specifications: 2.5 x 4(Ring Terminal)
4. Cable specifications: 2C x 0.75SQ or 2C x 18AW
Motor connection
Drive connection
10-48
Category
Product
Name
Name
(Note 1)
Applicable
Motors
Specifications
For power

Flat
motor
Power
cable

APCS-
FS-

*Front :
APCS-
PFS
(Load
direction)

* Rear :
APCS-
PFS-R
(Rear
direction)
All models
of
APM-FB
APM-FC
Series

1. Motor connection
a. Plug specifications: KN5FT04SJ1(JAE)
b. Plug specifications: ST-KN-S-C1B-3500 (JAE)
a. U,V and W pin specifications: 1512
b. FG pin specifications: 1.5x4 (Ring Terminal)
For power

Flat
motor
brake
cable

APCS-
BQS

*Front :
APCS-
BQS
(Load
direction)

* Rear :
APCS-
BQS-R
(Rear
direction)
All models
of
APM-FB
APM-FC
Series

1. Motor connection
a. Plug specifications: KN5FT02SJ1(JAE )
b. Socket specifications: ST-KN-S-C1B-3500 (JAE )
a. connection terminal specifications: 1.5x3(Ring Terminal)

10-49
Category
Product
Name
Name
(Note 1)
Applicable
Motors
Specifications
For power

Brake
Power
cable

APCS-
PSB
(new
model)

All models
of
APM-SG
APM-LG
APM-FG
Series

1. Motor connection
a. Plug specifications: MS3108B14-7S(MS)
a. connection terminal specifications: 1.5x3(Ring Terminal)

this information.

Motor connection
Drive connection
10-50
Optional cables
Category
Product
Name
Name
(Note 1)
Applicable
Drive
Specifications
For
signaling
CN1 Cable
APCS-
CN1A
L7N Series
[Upper controller] [Servo drive CN1]

a. Case specifications: 10320-52A0-008(3M)
b. Connector specifications: 10120-3000PE(3M)
2. Cable specifications: ROW-SB0.1Cx20C(AWG28)
T/B CN1 T/B
APCS-
L7NCN1T-

L7N
SERIES

a. CASE specification : 10320-52A0-008(3M)
b. CONNECTOR specification : 10120-3000PE (3M)
c. CABLE specification : AWG28 x 10P
2. Terminal block connection
a. CONNECTOR specification : HIF3BA-20D-
2.54R(Hirose)
b. Terminal block specification : XTB-20H(Samwon Act)
3. Cable length
For
signaling
Communicati
on cable
APCS-
CN5L7U
L7 Series

[PC - USB port] [Servo drive CN5]

1. PC connection: USB A plug
2. Drive connection (CN5): Mini USB 5P plug
3. Electrical requirements:
Double shielded, twisted pair, EMI filter installation
(similar product: KU-AMB518 by SANWA)
Indicates Pin no.
Drive connection
Terminal block connection
10.
10-51
CN
CN1
Connector
APC-
CN2NNA
L7N Series

1. Case specifications: 10320-52A20-008(3M)
2. Connector specifications: 10120-3000PE(3M)
CN
CN6
Connector
APCS-CN6J L7N Series

1. Plug Connector Kit : 2040008-1(TE)
CN
CN3/4
Connector
APCS-
CN4NNA
L7N Series

1. Connector specifications: 44915-0021(MOLEX)
2. Plug Housing specifications: WRJ-45(Wlztek)
Note 1) The in the name indicates the length of each cable. Refer to the following table for this
information.
Indication 01 02 03 05

11
20
1
10
11. Maintenance and Inspection
11-1
11.1 Maintenance and Inspection
This chapter explains how to perform basic maintenance and inspection tasks as well as
diagnose and troubleshoot the servo motor and drive.
11.1.1 Precautions
1. Measuring the motor voltage: The PWM controls the voltage output from the servo amp to the motor.
Because of this, the waves take the form of pulses. Use a rectifier voltmeter for accurate
measurements because different meters may produce different results.
2. Measuring the motor current: Use a moving iron ammeter and wait for the motor's reactance to
smooth the pulse waveform into sine waves.
3. Measuring the electric power: Use an electrodynamometer based on the 3 power meter method.
4. Other gauges: When using an oscilloscope or digital voltmeter, do not allow them to touch the
ground. Use a 1 mA or less input current gauge.
11.1.2 What to Inspect
Wait at least 10 minutes after turning off the power before beginning the inspection because
the condenser can hold enough voltage to cause an electrical accident.
(2) Inspecting the Servo Motor
Caution
Wait at least 10 minutes after turning off the power before beginning the inspection because the
condenser can hold enough voltage to cause an electrical accident.

InspectionItem InspectionPeriod
Inspectionand
Handling
Notes
Vibration and
sound check
Monthly
Touch the motor and
listen for sounds.
The feel and sounds
should be the same as
usual.
Inspect the exterior
of the motor
Depends on the amount
of contamination or
damage.
Clean the motor with a
cloth or air pressure.
-
Measure the
insulation
resistance
At least once a year
Disconnect the motor
from the drive and
measure the insulation
resistance.
A normal resistance
level is 10 or higher.

Note 1)

Contact our service
center if the resistance
is lower than 10 .
Replace the oil
seal
At least once
every 5,000 hours
Remove the oil seal
from the motor and
replace it.
This only applies to
motors with an oil seal.
11-2
InspectionItem InspectionPeriod
Inspectionand
Handling
Notes
General inspection
At least once every
20,000 hours or after 5
years.
Contact our service
center.
Do not disassemble the
servo motor yourself.
Note 1) Measure the resistance between the FG and one of the U, V, and W power lines on the servo
motor.
(3) Inspecting the Servo Drive
Inspection
Item
Inspection
Period
Inspectionprocess
Whattodoifyoufindan
abnormality
Clean the
main body
and control
board
At least once
a year
Check if there is any dust or
oil on the components.
Clean it with air pressure or
a cloth.
Check for
loose screws
At least once
a year
Check whether the screws are
loose on the terminals and
connectors.
Tighten the screws.
Check for
defective
parts on the
main body or
the control
board
At least once
a year
Check for discoloration,
damage, or disconnection
caused by heat.
Contact our company.

11-3
11.1.3 Replacing Parts
Mechanical friction and aging may deteriorate the following parts or even cause them to
malfunction. This makes it important to conduct regular maintenance checks and replace
worn parts.
1. The smoothing condenser: Ripple currents and other factors can cause this part to wear. The
lifespan of this part depends on the operating temperature and environment. It normally lasts for 10
years if used continuously in a normal air-conditioned environment. Inspect the condenser at least
once each year because it can rapidly age over a short period of time once it starts to deteriorate
(inspect it more frequently as it approaches obsolescence).
Visual inspection criteria:
a. The condition of the case: Check for deformations on the sides and bottom.
b. The condition of the lid: Check for notable expansion, severe cracks, or broken parts.
c. The relief valve: Check for notable valve expansion and operation.
d. Also regularly check whether the exterior is cracked, discolored, or leaking and whether there
are any broken parts. The condenser is obsolete when its capacity degrades to less than 85% of
the rated capacity.
2. The relays: Check for bad connections and wear and tear on the contacts caused by switching
currents. A relay is obsolete when its accumulated number of switches reaches 100,000,
depending on the power capacity.
3. Motor bearings: Replace the bearings after 20,000 to 30,000 hours of operation at the rated speed
under the rated load. Replace the bearings if abnormal sounds or vibrations are detected during
inspection, depending on the operating conditions.
The Standard Part Replacement Cycle
Part Name Standard Replacement Cycle Method
Smoothing condenser 7-8 years
Replace (determine after
inspection).
Relays - Determine after inspection
Fuses 10 years Replace
Aluminum electrolytic
condensers on printed
boards
5 years
Replace with new boards
(determined after inspection)
Cooling fans 4-5 years Replace
Motor bearings - Determine after inspection
Motor oil seal 5,000 hours Replace

11-4
11.2 Diagnosing and Troubleshooting
Abnormalities
AL- appears if a problem occurs during operation. If this happens, try to solve the problem
by following the troubleshooting advice given in this section. If the problem persists, contact
our service center.
11.2.1 The Servo Motor
Cause of abnormalities, inspection procedure, and troubleshooting methods
Symptoms Causes Inspection process Remedies
The motor
does not
move.
The P-OT and N-OT inputs
are off.
Refer to section 3.6, "Signals."
Turn on the P-OT and N-OT
inputs.
The motor has defects.
Use a resistance tester to measure
the resistance to the motor lead
terminal (resistance between phases:
several ohms).
Replace the motor.
The locking screws are loose. Check the locking screws. Tighten any loose screws.
The external wiring is
incorrect or the cables are
disconnected.
Check the wires to the motor and the
encoder.
Redo the wiring.
Replace the cables.
The encoder has defects. Check the output waves.
Replace the encoder.
(Contact our service center.)
Motor rotation
is unstable.
The connection is bad.
Check the connection of the motor
lead terminal.
Fix any bad connections.
The input voltage is low. Check the input voltage of the drive. Change the power source.
Overloads occur. Check the condition of the machine.
Remove any foreign substances
from the rotating unit and grease
or lubricate it.
The motor
overheats.
The ambient temperature is
too high.
Check the temperature around the
motor. (40 or lower)
Change heat transfer structure.
Install a cooling fan.
The surface of the motor is
contaminated.
Check whether there are any foreign
substances on the surface of the
motor.
Clean the surface of the motor.
Overloads occur.
Check the load on the drive.
Check the acceleration/deceleration
time.
Reduce the load.
Increase the
acceleration/deceleration time.
Use a motor with a greater
capacity.
The magnetic power of the
magnets is reduced.
Check the counter voltage and
voltage waveforms.
Replace the motor.
The device is
making a
strange
sound.
Coupling is bad.
Tighten the coupling screws and
measure the concentricity of the
connection.
Readjust the coupling.
The bearings are abnormal.
Check the bearings for vibrations and
sounds.
Contact us.
The parameters are set
incorrectly (the inertia, gain,
and time constants).
Check the parameters.
Refer to Chapter 6, "Object
Dictionary."
11-5
11.2.2 The Servo Drive
If an alarm occurs, then the malfunction signal output contact (ALARM) goes off and the dynamic brake stops the
motor.
Alarm Code Name Details What to check

IPM Fault Overcurrent (H/W)
Check for incorrect wiring in the drive
output and encoder.
Check the motor ID, drive ID, and
encoder settings.
Determine whether there is a conflict
or binding in the equipment.

IPM temperature IPM overheat
output and encoder.
encoder settings.

Overcurrent Overcurrent (S/W)
output and encoder.
encoder settings.

Current offset Abnormal current offset
Check whether the U-phase current
offset [0x2614] and V-phase current
offset [0x2615] are 5% of the rated
current or higher. Replace the drive.

Overcurrent (/CL) Overcurrent (H/W)
output and encoder.
encoder settings.

Continuous overload Continuous overload
Check the load and the condition of
the brake.
output and encoder.
Check the motor ID and encoder
settings.

Room temperature Drive overheat
Check the temperature inside the
drive [St-19].
Install a cooling fan and check the
load.

Regen. Overload Regenerative overload
Check the input voltage, regenerative
braking resistance, and wiring.
Replace the drive.

Motor cable open Motor disconnection Check the wiring of the motor.

Encoder comm.
Serial encoder
communication error
Check for incorrect wiring of the serial
encoder.

Encoder cable open
Encoder cable
disconnection
Check whether the encoder cable is
disconnected.
11-6
Alarm Code Name Details What to check

Encoder data error Encoder data error
Check the encoder settings and
wiring.

Motor setting error Motor ID setting error Replace the encoder.

Low Battery Error Low voltage error
Low voltage of Back Up battery, when
Absolute encoder is applied.
Reset the operation after changing
battery.
(Applied after S/W Ver 1.3)

Under voltage Low voltage
Check input voltage and power unit
wiring.

Overvoltage Overvoltage
Check the input voltage and wiring.
Check the braking resistance for
damage.
Check for excessive regenerative
operation. Check the regenerative
resistance.

RST power fail Main power failure
Check the power unit wiring and
power supply.

Control power fail Control power failure
Check the power unit wiring and
power supply.

Over speed limit Overspeed
Check the encoder, encoder settings,
encoder wiring, gain settings, motor
wiring, motor ID, electric gear ratio,
and speed command scale.

Position following Excessive position error
Check the Following Error Window
[0x6065], wiring and limit contacts,
gain setting values, encoder settings,
and electric gear ratio settings. Check
the load on the equipment and
whether there is binding on the
equipment.

Encoder Position
Difference
Difference between 2
encoders
Check value of difference between
internal and external encoder or
external encoder when Full-Closed
control

EtherCAT Comm.Err
1
EtherCAT
communication
malfunction
Check the CN3 and CN4 connectors
and the EtherCAT communication
cable. Replace the drive.
EtherCAT Comm.Err
2

EtherCAT Comm.Err
3

Invalid factory setting Invalid factory settings
Restore the default parameters
[0x1011].

GPIO setting
Output contact point
setting error
Restore the default parameters
[0x1011].

11-7
A warning code appears in the current operation status [St-00] if the servo drive is operating abnormally. Check the
warning code to determine what you need to inspect. For EMG [W-80] errors, however, the dynamic brake stops the
motor.
Warning
State
(CODE)
Name Details and causes What to check

RST_PFAIL Main power phase loss
The equipment does not receive main
power when the handling method for the
main power phase loss [0x2003] is set to 1.

LOW_BATT Low battery
The output voltage of the encoder backup
battery is insufficient when applying an
absolute encoder.

OV_TCMD
Excessive Torque
Command
You have exceeded the maximum number
of torque commands.

OV_VCMD
Excessive speed
command
You have exceeded the maximum number
of speed commands.

OV_LOAD Overload warning
The accumulated overload has reached the
overload warning level [0x200A].

SETUP Capacity settings
The electric current capacity of the motor is
larger than that of the drive.

UD_VTG Low voltage warning
The DC-link voltage is 190V or below when
second bit of [0x2003] is set to 1.

EMG EMG warning
Check the emergency stop contact signal
and the external 24 V power.

STO connection error STO connection error
Check the operation and connection
setting.

CCW Limit CCW Limit on setting
Check the setting and point of contact.

CW Limit CW Limit on setting
Check the setting and point of contact.

11-8
Servo Drive Overload Graphs (400 W or less)
(1) Rotation overload graph
Load
(%)
AL-21
Occurri
ng Time
(sec)
Max Min
Load
(%)
AL-21
Occurri
ng Time
(sec)
Max Min
100% or
less

110 55776.0 89241.6 33465.6 210 66.8 106.9 40.08
120 13944.0 22310.4 8366.4 220 50.1 80.2 30.06
130 6197.3 9915.7 3718.38 230 38.5 61.6 23.1
140 3486.0 5577.6 2091.6 240 30.3 48.5 18.18
150 1183.0 1892.8 709.8 250 24.2 38.7 14.52
160 566.0 905.6 339.6 260 4.2 6.7 2.52
170 318.0 508.8 190.8 270 3.8 6.1 2.28
180 198.0 316.8 118.8 280 3.4 5.4 2.04
190 131.0 209.6 78.6 290 3.0 4.8 1.8
200 92.0 147.2 55.2 300 2.7 4.3 1.62

Load rate (%)
T
i
m
e

(
s
e
c
.
)

Load curve during rotation
11-9
(2) Stoppage overload graph
Load (%)
AL-21
Occurrin
g Time
(sec)
Max Min
Load
(%)
AL-21
Occurri
ng Time
(sec)
Max Min
100% or
less

110 37937.7 60700.3 22762.62 210 50.1 80.2 30.06
120 9483.9 15174.2 5690.34 220 38.5 61.6 23.1
130 4215.1 6744.2 2529.06 230 30.3 48.5 18.18
140 2371.0 3793.6 1422.6 240 9.7 15.5 5.82
150 926.0 1481.6 555.6 250 8.3 13.3 4.98
160 470.0 752.0 282 260 3.8 6.1 2.28
170 273.0 436.8 163.8 270 3.4 5.4 2.04
180 173.0 276.8 103.8 280 3.1 5.0 1.86
190 117.0 187.2 70.2 290 2.7 4.3 1.62
200 66.0 105.6 39.6 300 2.5 4.0 1.5

Load rate (%)
T
i
m
e

(
s
e
c
.
)

Load curve when stopped
11-10
Servo Drive Overload Graphs (SA type,100 W or less)
Load (%)
AL-21
Occurrin
g Time
(sec)
Max Min
Load
(%)
AL-21
Occurri
ng Time
(sec)
Max Min
100% or
less

110 1696.0 2713.6 1017.6 210 5.2 8.3 3.12
120 424.0 678.4 254.4 220 4.4 7.0 2.64
130 188.4 301.5 113.064 230 3.8 6.1 2.28
140 106.0 169.6 63.6 240 3.3 5.3 1.98
150 70.4 112.6 42.24 250 2.9 4.6 1.74
160 26.8 42.9 16.08 260 2.6 4.2 1.56
170 20.6 33.0 12.36 270 2.3 3.7 1.38
180 16.2 25.9 9.72 280 2.0 3.2 1.2
190 13.0 20.8 7.8 290 1.8 2.9 1.08
200 10.5 16.8 6.3 300 1.6 2.6 0.96

T
i
m
e

(
s
e
c
.
)

Load rate (%)
100W or Lower SA Type
11-11
Load
(%)
AL-21
Occurri
ng Time
(sec)
Max Min
Load
(%)
AL-21
Occurri
ng Time
(sec)
Max Min
100% or
less

110 1372.8 2196.5 823.68 210 3.9 6.2 2.34
120 343.2 549.1 205.92 220 3.4 5.4 2.04
130 152.5 244.0 91.518 230 3.0 4.8 1.8
140 85.8 137.3 51.48 240 2.6 4.2 1.56
150 58.6 93.8 35.16 250 2.3 3.7 1.38
160 16.2 25.9 9.72 260 2.0 3.2 1.2
170 13.0 20.8 7.8 270 1.8 2.9 1.08
180 10.5 16.8 6.3 280 1.6 2.6 0.96
190 8.7 13.9 5.22 290 1.5 2.4 0.9
200 7.2 11.5 4.32 300 1.3 2.1 0.78

T
i
m
e

(
s
e
c
.
)

Load rate (%)
100 W or Lower SA Type
11-12
Servo Drive Overload Graphs (800 W and 1 KW)
Load
(%)
AL-21
Occurri
ng Time
(sec)
Max Min
Load
(%)
AL-21
Occurri
ng Time
(sec)
Max Min
100% or
less

110 105800.0 169280.0 63480 210 119.0 190.4 71.4
120 26450.0 42320.0 15870 220 89.2 142.7 53.52
130 11755.0 18808.0 7053 230 49.3 78.9 29.58
140 6612.5 10580.0 3967.5 240 38.8 62.1 23.28
150 2244.0 3590.4 1346.4 250 31.0 49.6 18.6
160 1073.6 1717.8 644.16 260 7.0 11.2 4.2
170 603.2 965.1 361.92 270 6.4 10.2 3.84
180 413.6 661.8 248.16 280 5.7 9.1 3.42
190 273.6 437.8 164.16 290 5.0 8.0 3
200 201.0 321.6 120.6 300 4.6 7.4 2.76

Load rate (%)
T
i
m
e

(
s
e
c
.
)

11-13
Load (%)
AL-21
Occurrin
g Time
(sec)
Max Min
Load
(%)
AL-21
Occurri
ng Time
(sec)
Max Min
100% or
less

110 72512.0 116019.2 43507.2 210 93.4 149.4 56.04
120 18128.0 29004.8 10876.8 220 71.8 114.9 43.08
130 8056.9 12891.0 4834.14 230 53.7 85.9 32.22
140 4532.0 7251.2 2719.2 240 17.2 27.5 10.32
150 1770.0 2832.0 1062 250 14.7 23.5 8.82
160 898.4 1437.4 539.04 260 6.7 10.7 4.02
170 521.8 834.9 313.08 270 6.0 9.6 3.6
180 334.1 534.6 200.46 280 5.7 9.1 3.42
190 226.0 361.6 135.6 290 5.0 8.0 3
200 134.0 214.4 80.4 300 4.6 7.4 2.76

Load rate (%)
T
i
m
e

(
s
e
c
.
)

11-14
Servo Drive Overload Graphs (2 KW and 3.5 KW)
Load
(%)
AL-21
Occurri
ng Time
(sec)
Max Min
Load
(%)
AL-21
Occurri
ng Time
(sec)
Max Min
100% or
less

110 4832.0 7731.2 2899.2 210 66.8 106.9 40.08
120 1208.0 1932.8 724.8 220 50.1 80.2 30.06
130 536.9 859.0 322.1333 230 38.5 61.6 23.1
140 302.0 483.2 181.2 240 30.3 48.5 18.18
150 257.0 411.2 154.2 250 24.2 38.7 14.52
160 229.0 366.4 137.4 260 4.2 6.7 2.52
170 200.0 320.0 120 270 3.8 6.1 2.28
180 165.0 264.0 99 280 3.4 5.4 2.04
190 131.0 209.6 78.6 290 3.0 4.8 1.8
200 103.0 164.8 61.8 300 2.7 4.3 1.62

Load rate (%)
T
i
m
e

(
s
e
c
.
)

11-15
Load (%)
AL-21
Occurrin
g Time
(sec)
Max Min
Load
(%)
AL-21
Occurri
ng Time
(sec)
Max Min
100% or
less

110 4832.0 7731.2 2899.2 210 44.0 70.4 26.4
120 1208.0 1932.8 724.8 220 36.0 57.6 21.6
130 536.9 859.0 322.1333 230 30.3 48.5 18.18
140 302.0 483.2 181.2 240 9.7 15.5 5.82
150 154.0 246.4 92.4 250 8.3 13.3 4.98
160 110.0 176.0 66 260 3.8 6.1 2.28
170 90.0 144.0 54 270 3.4 5.4 2.04
180 75.0 120.0 45 280 3.1 5.0 1.86
190 61.0 97.6 36.6 290 2.7 4.3 1.62
200 52.0 83.2 31.2 300 2.5 4.0 1.5

Load rate (%)
T
i
m
e

(
s
e
c
.
)

12. Appendix
12-1
12. Appendix
12.1 Motor Types and IDs
Model Name ID Watt Notes Model Name ID Watt Notes
SAR3A 1 30 SE13G 75 1300
SAR5A 2 50 SE17G 76 1700
SA01A 3 100 HE09A 77 900 Hollow type
SA015A 5 150 HE15A 78 1500 Hollow type
SB01A 11 100 SF30A 81 3000
SB02A 12 200 SF50A 82 5000
SB04A 13 400 SF22D 85 2200
HB02A 15 200 Hollow type LF35D 190 3500
HB04A 16 400 Hollow type SF55D 87 5500
SF75D 88 7500
SC04A 21 400 SF12M 89 1200
SC06A 22 600 SF20M 90 2000
SC08A 23 800 LF30M 192 3000
SC10A 24 1000 SF44M 92 4400
SC03D 25 300 SF20G 93 1800
SC05D 26 450 LF30G 191 2900
SC06D 27 550 SF44G 95 4400
SC07D 28 650 SF60G 96 6000

SE09A 61 900 SG22D 111 2200
SE15A 62 1500 LG35D 193 3500
SE22A 63 2200 SG55D 113 5500
SE30A 64 3000 SG75D 114 7500
SE06D 65 600 SG110D 115 11000
SE11D 66 1100 SG12M 121 1200
SE16D 67 1600 SG20M 122 2000
SE22D 68 2200 LG30M 195 3000
SE03M 69 300 SG44M 124 4400
SE06M 70 600 SG60M 125 6000
SE09M 71 900 SG20G 131 1800
SE12M 72 1200

LG30G 194 2900
SE05G 73 450 SG44G 133 4400
SE09G 74 850 SG60G 134 6000
12. Appendix
12-2
SG85G 135 8500 FF30A 781 3000
SG110G 136 11000 FF50A 782 5000
SG150G 137 15000 FF22D 785 2200
FF35D 786 3500
FB01A 711 100 FF55D 787 5500
FB02A 712 200 FF75D 788 7500
FB04A 713 400 FF12M 789 1200
FF20M 790 2000
FC04A 721 400 FF30M 791 3000
FC06A 722 600 FF44M 792 4000
FC08A 723 800 FF20G 793 1800
FC10A 724 1000 FF30G 794 2900
FF44G 795 4400
FC03D 725 300 FF60G 796 6000
FC05D 726 500 FF75G 804 7500
FC06D 727 600
FC07D 728 700 FG22D 811 2200
FG35D 812 3500
FE09A 761 900 FG55D 813 5500
FE15A 762 1500 FG75D 814 7500
FE22A 763 2200 FG12M 821 1200
FE30A 764 3000 FG20M 822 2000
FE06D 765 600 FG30M 823 3000
FE11D 766 1100 FG44M 824 4400
FE16D 767 1600 FG20G 831 1800
FE22D 768 2200 FG30G 832 2900
FE03M 769 300
FE06M 770 600
FE09M 771 900
FE12M 772 1200
FE05G 773 450
FE09G 774 850
FE13G 775 1300
FE17G 776 1700

12. Appendix
12-3
DB03D 601 63
DB06D 602 126
DB09D 603 188
DC06D 611 126
DC12D 612 251
DC18D 613 377
DD12D 621 251
DD22D 622 461
DD34D 623 712
DE40D 632 838
DE60D 633 1257
DFA1G 641 1728
DFA6G 642 2513

12. Appendix
12-4
12.2 Test Drive Procedure
Thank you for purchasing our product. Perform the following process to conduct the initial
test drive:
Caution
After attaching the servo motor to your equipment, perform the initial operation test and test drive
without any load (without any coupling or belt) for safety. Connect the load to the motor for the final
test drive.

Order Details
Product check
Check the name tag to verify that the product received matches the model ordered
(refer to section 1.1).
Check the name tag attached to the right side of the product (to the right side of
the shaft on the motor).
Main check point: Check the product capacity and options.
Power
connectivity
Wire a single-phase AC 220 V power supply to control power input C1 and C2, and
a three-phase AC 220 V power supply to main power input L1, L2, and L3 (refer to
section 3.2).
The product can run on a single-phase AC 220 V power supply, but this reduces
torque and the lifespan of the product. Be sure to input a three-phase AC 220 V
power supply.
Signal line
wiring
Connect the CN1 (I/O), CN3, CN4, CN5 (communication), CN6 and CN2 encoder
cables, and motor power cable based on the operation mode (refer to section 1.2
and chapter 3).
Always use robot cables if the motor moves.
Use twist shield cables for the signal and encoder cables.
Tighten the bolts after locking the encoder cable connector (drive direction).
Do not modify the U, V, and W wiring of the motor power cable.
Do not confuse the CN3 EtherCAT communication port input and the CN4
EtherCAT communication port output cables during wiring.
Install a safety jump cable when you are not using a CN6 safety connector.
Control power
on
Supply single-phase AC 220 V power to C1 and C2.
Check the external input voltage before turning on the servo drive.
Check whether the display operates normally (there should not be any broken
7-segments or alarms).
Main power
on
Supply three-phase AC 220 V power to L1, L2, and L3.
Check the external input voltage before turning on the servo drive.
The red charge LED at the bottom of the loader window turns on when the drive
receives power.
If an alarm appears, it indicates that there is an error in the power circuit, servo
motor wiring, or encoder wiring.
Turn off the power and fix the error using the information in "Alarm Codes and
Descriptions."
PDO Mapping
Set the PDO mapping. ex) CSP Mode
Define the Status Word [0x6041], the Position Actual Value [0x6064], and the
Mode of Operation [0x6060] in 2nd Transmit PDO mapping.
Define the Control Word [0x6040] and the Target Position [0x607A] in 2nd
Receive PDO mapping.
The content above is the built-in PDO mapping of the L7N. These settings are
defined in the EtherCAT Slave Information file (XML file). In addition, the user can
change the PDO mapping (however, PDO mapping can be done for up to 8
variables).
12. Appendix
12-5
Order Details
State Machine
Convert the state machine to operational status (refer to section 4.3).
Perform the conversion in the following order: Init Pre-Op Safe-Op Op.
The L/A0 and the L/A1 LEDs blink and the Run LED turns on when the state
machine is operational.
Check the
motor
Read the motor ID [0x2000] and the encoder type [0x2001] from the EtherCAT
master to check whether they match the motor ID and encoder type on the product
name plate attached to the right side of the motor.
Set the
control mode
Change the Mode of Operation [0x6060] to CSP.
Write Dec. 8 in the Mode of Operation [0x6060].
0: no mode 1: Pp 3: Pv 4: Tp 6: Hm
7: Ip 8: Csp 9: Csv 10: Cst
Operation 1
Activate the Controlword bit, according to the control mode, to drive the L7N to the
target position
(refer to section 7.6, "CiA402 Objects").
Operation 2
11. Adjust the following parameter data to perform the Csv mode operation with the
upper level controller.
Target Velocity: [0x60FF]
Velocity Offset: [0x60B1]
Torque Offset: [0x60B2]
Profile Deceleration Time: [0x6084]
Quick Stop Deceleration Time : [0x6085]
Velocity Demand Value: [0x606B]
Velocity Actual Value: [0x606C]
Velocity Window: [0x606D]
Velocity Window Time: [0x606E]

12. Appendix
12-7

User Manual Revision History

Number Date issued Revised content Version number Notes
1 2012.09.10 Add contents 1.1
2 2012.11.19
Add Multi turn encoder
contents, parameters.
1.2
3 2013.02.18
Revise product features of
servo motor.
1.3
4 2013.07.20 Add contents 2.0

Green Management
LS Mecapion considers protecting the
environment a high priority. We work hard
to protect the Earth.
The LS Mecapion servo drive is
environmentally friendly.
You can disassemble the drive and recycle
the iron, aluminum, bronze, and synthetic
resin (cover) components.

HEAD OFFICE
LS tower, Hogye-dong, Dongan-gu, Anyang-si, Gyeonggi-do 1026-6,
Korea http://eng.lsis.biz
Tel : (82-2)2034-4870/Fax : 82-2-2034-4648 e-mail : [email protected]
LSIS Tokyo Office _ Tokyo, Japan
Address: 16FL. Higashi-Kan. Akasaka Twin Tower 17-22,
Akasaka.Monato-ku Tokyo 107-8470. Japan
Tel : 81-3-3582-9128/Fax : 81-3-3582-2667 e-mail : [email protected]
LSIS (ME) FZE _ Dubai, U.A.E.
Address : Jafza View Tower Lob 19, Room 205 Along Sheikh Zayed
Road Jebel Aali Free Zone Dubai, United Arab Emirates
LSIS Shanghai Office _ Shanghai, China
Address : Room E-G. 12FL Hiamin Empire Plaza. No.726. West.
Yan'an Road Shanghai 200050. P.R. China e-mail : [email protected]
Tel : 86-21-5237-9977(609)/Fax : 89-21-5237-7189
LSIS Beijing Office _ Beijing, China
Address : B-Tower 17FL. Beijing Global Trade Center B/D. No. 36.
East BeisanHuan-Road. DongCheng-District. Beijing 100013. P.R. China
Tel : 86-10-5825-6027(666)/Fax : 86-10-5825-6028 e-mail : [email protected]
LSIS Guangzhou Office _ Guangzhou, China
Address : Room 1403.14FL. New Poly Tower.
2 Zhongshan Liu Road.Guangzhou.P.R China

LSIS Chengdu Office _ Chengdu, China
Address : 12FL. Guodong Buiding. No.52 Jindun
Road Chengdu.610041. P.R. China
Tel : 86-28-8612-9151(9226)/Fax : 86-28-8612-9236 e-mail : [email protected]
LSIS Qingdao Office _ Qingdao, China
Address : YinHe Bldg. 402 Room No. 2P Shandong Road,
Qingdao-City,Shandong-province 266071, P.R. China
LSIS Europe B.V. , Netherlands
Address : 1st. Floor, Tupolevlaan 48, 1119NZ, Schiphol-Rijk, The Netherlands
Tel : +31 (0)20 654 1420/Fax : +31 (0)20 654 1429 e-mail : [email protected]
Wuxi LSIS Co., Ltd _ Wuxi, China
Address : 102-A. National High & New Tech Industrial Development Area.
Wuxi. Jiangsu. 214028. P.R. China
Dalian LSIS Co., Ltd. _ Dalian, China
Address : No. 15. Liaohexi 3-Road. Economic and Technical Development zone.
Dalian 116600. China

LSIS constantly endeavors to improve its product so that
information in this manual is subject to change without notice.
2013 LSIS Co., Ltd All Rights Reserved.

2014. 2
LSIS values every single customers.
Quality and service come first at LSIS.
Always at your service, standing for our customers.
http://www.lsis.com

User+Manual XDL-L7N+series Eng V1.5

Uploaded by

Copyright:

Available Formats

User+Manual XDL-L7N+series Eng V1.5

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

User+Manual XDL-L7N+series Eng V1.5

Uploaded by

Copyright:

Available Formats

Safety Precautions

You might also like