Scribd
Upload
45 views4 pages

Lab Report271

This lab report summarizes experiments conducted on an Altera DE1 Prototype Board using gates, LEDs, switches, and breadboards. The first experiment connected a switch to an LED using a wire to test connectivity. Subsequent experiments introduced an inverter gate and two inverter gates between switches and LEDs. A final experiment used a two-input NOR gate connected to two switches and an LED. Results were shown in tables confirming expected gate behaviors. The report concludes by presenting a schematic of the NOR gate circuit and describing steps to generate a waveform simulation file.

Uploaded by

Fuzalert
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
45 views4 pages

Lab Report271

This lab report summarizes experiments conducted on an Altera DE1 Prototype Board using gates, LEDs, switches, and breadboards. The first experiment connected a switch to an LED using a wire to test connectivity. Subsequent experiments introduced an inverter gate and two inverter gates between switches and LEDs. A final experiment used a two-input NOR gate connected to two switches and an LED. Results were shown in tables confirming expected gate behaviors. The report concludes by presenting a schematic of the NOR gate circuit and describing steps to generate a waveform simulation file.

Uploaded by

Fuzalert
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Lab 1 Report

Hassan Uraizee
EE271
Introduction:
This lab report was an introduction of a Altera Terasic DE1 Prototype Board
the solder!less bread board and the "A"D #ates "$% as well as in&erters'
(e were introduced to the )wishes *eys and +ED) on the DE1 Prototype
Board' Another introduction in this lab was towards the #uidance of wirin# on
the bread board and the prototype board'
Procedures:
(e were #i&en a laboratory desi#n *its which included, a DE1 Prototypin#
Board a bread board attached to the prototypin# board and the
-nput.$utput /onnectors attached to the prototypin# board one U)B cable
one +o#ic probe and a set of chips 0#ates1' The initial step of startin# this lab
was the assi#n2ent of usin# wires switches #ates and +EDs on the DE1
board and the bread board' (e use the +o#ic Probe to test the polarity of the
switch as #uided in the assi#n2ent' After that after readin# carefully the
instructions we turn of the power to the 2ain board #ettin# ready for the
ne3t e3peri2ent' (e then connect a switch to an +ED by a wire to be
speci4c5 we connected +ED%6 to )(6 and then we turn on and o7 the switch
to test the connection' Easy enou#h the 4rst e3peri2ent was carried out
successfully' (e continued to 2o&e on to the ne3t e3peri2ent and of course
the power was turn o7 as instructed' The ne3t e3peri2ent was to place an
in&erter 0"$T #ate1 between the switch and a +ED' The chip was fully
functional as the connections were carefully e3a2ined and done' The #round
pin and the 8DD pin were correctly connected' (e *new the in&erter had 9
built!in in&erters so pic*ed the in&erter which had input at pin1 and output
at pin2' (e constructed a table after :ippin# the switch a few ti2es' The
table will be shown in the results section' "e3t we connected two in&erters
fro2 pin 1 to pin;' They beha&ed e3actly as what we were e3pected'
"e3t step is to connect a two input "$% ate to two switches and one +ED'
The procedures were pretty si2ilar to the pre&ious e3peri2ent' (e 2ade
sure the connection was accurate' After :ippin# the switches a few ti2e we
constructed a table' The table will be show in later section'
Results/Conclusion:
Inverter experiment result tables
1 inverter:
)witch +ED 0$" or $<<1
$" $<<
$<< $"

2 inverters:
)witch +ED 0$" or $<<1
$" $"
$<< $<<
NOR gates experiment result tables:
)witch 1 )witch 2 +ED
$<< $<< $"
$<< $" $<<
$" $<< $<<
$" $" $<<
<ro2 the e=uation f x1 ! x2 "

x2
! x# we *now that there are 2 A"D
#ates connected to an $% #ate' <inally we ca2e up with the sche2actic of
circuit,
<ro2 this sche2atic window we clic* $le !> ne%& The new tab will pop up'
To 2a*e wa&efor2 for this we choose 'niversit( Program )*+' The
si2ulation wa&efor2 editor will be opened' "e3t we need to i2port data
fro2 sche2atic to editor so that it can 2a*e wa&efor2 for us' (e clic* ,dit
-. Insert -. Insert Node or /us0 Then we need to 4nd node by choosin#
Node +inder' <ro2 there we probably will see ; inputs that we 2ade' Then
clic* O1& And here is our wa&efor2 for the ;!#ate circuit f x1 ! x2 "

x2

! x#&

You might also like