Scribd
Upload
202 views

Network Components, Cables and Connectors: Lab Handout 1

This document discusses network components and cables. It describes common devices like routers, switches, hubs and their functions. It outlines different cable types including coaxial, twisted pair and fiber optic cables. It provides details on creating and identifying straight-through and crossover Ethernet cables using RJ-45 connectors. The objectives are to study network cables, connectors and components and prepare crossover and direct cables in the lab.

Uploaded by

api-3739389
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
202 views

Network Components, Cables and Connectors: Lab Handout 1

This document discusses network components and cables. It describes common devices like routers, switches, hubs and their functions. It outlines different cable types including coaxial, twisted pair and fiber optic cables. It provides details on creating and identifying straight-through and crossover Ethernet cables using RJ-45 connectors. The objectives are to study network cables, connectors and components and prepare crossover and direct cables in the lab.

Uploaded by

api-3739389
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 9

Lab Handout 1

Network Components, Cables and Connectors


Objectives: Study different types of networking cables, connectors and other network
components. Prepare Cross-over and Direct cables.

Equipment:

1. Router
2. Switches
3. HUB
4. CAT-5 UTP Cable
5. Crimping tools
6. RJ-45 Jacks

Background:

Local Area Network (LAN)


There are numerous devices associated with data information flow across a LAN. When adjoined, they
create the infrastructure of a functional LAN. These devices include:

• Repeaters
• Bridges
• Hubs
• Switches
• Routers

Repeaters
Repeaters, located within the physical layer of a network, regenerate and propagate signals from one to
another. They do not change any information being transmitted, and they cannot filter any information.
Repeaters help to extend the distances of networks by boosting weak signals.

Bridges
Bridges are intelligent repeaters. They regenerate transmitted signals, but
unlike repeaters, they can also determine destinations.

Hubs Hubs connect all computer LAN connections into one device. They are
nothing more than multiport repeaters. Hubs cannot determine
destinations; they merely transmit to every line attached in a half-duplex
mode.
Routers
Routers are a step up from bridges. They are able to route and
filter information to different networks. Some routers can
automatically detect problems and redirect information around
the problem area. These are called "intelligent routers."

Switches

Switches connect all computer LAN connections, the same as hubs do.
The difference is that switches can run in full-duplex mode and are able
to direct and filter information to and from specific destinations.

WAN

WAN Infrastructure
As with LANs, there are numerous devices associated with data information flow across a WAN. Together, these
devices create the infrastructure of a functional WAN. These devices include:

• Router
• ATM Switch
• Modem and CSU/DSU
• Communication Server
• Multiplexer
• X.25/Frame Relay Switches

Routers
Routers are a step up from bridges. They are able to route and filter
information to different networks. Some routers can automatically detect
problems and redirect information around the problem area. These are
called "intelligent routers."
ATM Switches
ATM Switches provide
high-speed transfer
between both LANs and
WANs.

Modem (modulator / demodulator)

Modems convert digital and analog signals. At the source, modems convert digital signals to a form suitable
for transmission over analog communication facilities (public telephone lines). At the destination, modems
convert the signal back to a digital format.

CSU/DSU (Channel Service Unit / Data Service Unit)


CSUs/DSUs are similar to modems, however they send data in digital format across digital telephone loops. They
are usually in a physical box, but they may come in two separate units: CSUs or DSUs.

Multiplexers

A Multiplexer combines multiple signals for transmission over a single circuit. This allows for the transfer of
various data simultaneously, such as video, sound, text, etc.
Media / Cabling
Local Area Network Cabling
The earliest LANs used coaxial cables. Over time, the twisted pair cables used in
telephone systems were improved to carry higher frequencies and support LAN traffic.
More recently, fiber optic cables have emerged as a high-speed cabling option.
Local Area Networks use four types of cables:

• Coaxial
• Unshielded Twisted Pair (UTP)
• Shielded Twisted Pair (STP)
• Fiber Optic

Coaxial Cables

A coaxial cable consists of:


• a single copper conductor
• a layer of shielding with a ground wire
• an outer jacket

Coaxial Cable Uses


Coaxial cables are sometimes used for bus topologies, but many LAN products are
dropping support of coaxial cable connectivity.
The Ethernet LAN protocol was originally developed to operate over coaxial cables.
10Base5 / Thicknet cable:
• is an RG/U-8 coaxial cable.
• was the original Ethernet cable.
10Base2 / Thinnet cable:
• is an RG/U-58 coaxial cable.
• has a smaller diameter than Thicknet.
• replaced Thicknet.
• is no longer recommended, but is still used in some very small LANs.

Unshielded Twisted Pair


Unshielded twisted pair (UTP) cable is used for both
LANs and telephone systems. UTP cables are
composed of four color-coded pairs of copper
conductors twisted around each other. An outer
jacket provides protection and keeps the pairs in
alignment. UTP cable connects to devices via 8 pin
modular connectors called RJ-45 plugs. All LAN
protocols can operate over UTP. Most modern LAN
devices are equipped with RJ-45 jacks.

How is UTP Categorized?


There are 5 categories (levels) for UTP cable. These support low-speed voice signals
and high-speed LAN signals. Category 5 UTP is the recommended minimum category
for LAN installations. It is well-suited to star topologies. The following chart shows the
specifications for each category:

Performance
Category (MHz) Usage
CAT 1 1 Voice, Mainframe, Dumb Terminal
CAT 2 4 4 MB Token Ring
CAT 3 10 10MB Ethernet
CAT 4 20 16 MB Token Ring
CAT 5 100 100 MB Ethernet

• Shielded Twisted Pair


Shielded twisted pair is a special kind of copper telephone wiring used
in some business installations. An outer covering or shield is added to
the ordinary twisted pair.
STP cable is also used for Data Networks. It originated with IBM's Token-Ring
networks. Its shielding allows greater tolerances for protection from EMI interference,
such as from flourescent light fixtures and electric motors.

What are Drawbacks of STP?


STP cable has several drawbacks:

• Its attenuation may increase at high frequencies.


• At high frequencies, balance may decrease if the effects of the shield are not
compensated for leading to crosstalk and signal noise.
• The biggest drawback is the cost and physical size of the cabling.

Fiber Optic Cable

Fiber Optic cables are the


latest development in
cabling technology. They
are constructed from
optical glass. There is a
central glass filament,
called the core, and
surrounding layers of
cladding, buffer coatings,
strengthening materials,
and an outer jacket.

Information is transmitted by wavelengths of light. This is accomplished through


devices that convert electrical signals into rapid pulses of either LED or Laser light.

What Are the Advantages of Fiber Optics?


Fiber optic cables offer several advantages, including:
• high bandwidth capacity (many gigabits per second).
• longer distances between devices (from 2 to over 60 kilometers).
• immunity to electromagnetic interferences
Fiber optic cables are widely used in WANs for both voice and data communications.
The primary barrier to their widespread use in LANs is the cost of electronics. The cost
of the fiber optic cables themselves is comparable to UTP LAN cables.
Cross-over cable: In order to connect to similar devices like two computers, two routers,
two switches, we use cross over cable.

Straight through cable: Used to connect two dissimilar devices, like PC to switch, PC to
Bridge, PC to router etc we use straight through cable.

Crimping Tool: The tool used for making the RJ-45 and RJ-11 connection is called
crimping tool

RJ-45 Straight Through cable Pin assignment

Straight Through Cable Color Code Color


Pin 1 white orange
Pin 2 orange
Pin 3 white green
Pin 4 blue
Pin 5 white blue
Pin 6 green
Pin 7 white brown
Pin 8 brown
RJ-45 Cross-over cable
:
End 1 End 2
Brown Brown
White-Brown White-Brown
Green Orange
White-Blue White-Blue
Blue Blue
White-Green White-Orange
Orange Green
White-Orange White-Green
Procedure
1. Study the Hubs, Switches and Router in detail.
2. Study the Co-axial cable and twisted –pair cable, their characteristics and
properties in detail.
3. Using the RJ-45 crimping tool, prepare the cross over and direct cable.
4. Attach the cables with the computer Network card and the HUB.
5. Check the connectivity. The LED on the switch and computer’s Network interface
card should be ON.
6. Connect the two computers together using Crossover cable you made and check
the connectivity.

You might also like